OSDN Git Service
Srinivas Kandagatla [Mon, 30 Jun 2014 17:29:57 +0000 (18:29 +0100)]
usb: phy: msm: Do not do runtime pm if the phy is not idle
Use case is when the phy is configured in host mode and a usb device is
attached to board before bootup. On bootup, with the existing code and
runtime pm enabled, the driver would decrement the pm usage count
without checking the current state of the phy. This pm usage count
decrement would trigger the runtime pm which than would abort the
usb enumeration which was in progress. In my case a usb stick gets
detected and then immediatly the driver goes to low power mode which is
not correct.
log:
[ 1.631412] msm_hsusb_host
12520000.usb: EHCI Host Controller
[ 1.636556] msm_hsusb_host
12520000.usb: new USB bus registered, assigned bus number 1
[ 1.642563] msm_hsusb_host
12520000.usb: irq 220, io mem 0x12520000
[ 1.658197] msm_hsusb_host
12520000.usb: USB 2.0 started, EHCI 1.00
[ 1.659473] hub 1-0:1.0: USB hub found
[ 1.663415] hub 1-0:1.0: 1 port detected
...
[ 1.973352] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[ 2.107707] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.108993] scsi0 : usb-storage 1-1:1.0
[ 2.678341] msm_otg
12520000.phy: USB in low power mode
[ 3.168977] usb 1-1: USB disconnect, device number 2
This issue was detected on IFC6410 board.
This patch fixes the intial runtime pm trigger by checking the phy
state and decrementing the pm use count only when the phy state is IDLE.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Thomas Petazzoni [Mon, 30 Jun 2014 12:09:25 +0000 (14:09 +0200)]
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
On Marvell Armada XP, when a CPU comes back from deep idle state of
cpuidle, it restarts its execution at armada_370_xp_cpu_resume(),
which puts back the CPU into the coherency, and then calls the generic
cpu_resume() function.
While this works on little-endian configurations, it doesn't work on
big-endian configurations because the CPU restarts in little-endian,
and therefore must be switched back to big-endian to operate
properly. To achieve this, a 'setend be' instruction must be executed
in big-endian configurations. However, the ARM_BE8() macro that is
used to implement nice compile-time conditional for ARM LE vs. ARM BE8
is not easily usable in inline assembly.
Therefore, this patch moves the armada_370_xp_cpu_resume() C function,
which was anyway just a block of inline assembly, into a proper
pmsu_ll.S file, and adds the appropriate ARM_BE8(setend be)
instruction.
Without this patch, an Armada XP big endian configuration with cpuidle
enabled fails to boot, as it hangs as soon as one of the CPU hits the
deep idle state.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404130165-3593-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 12 Jun 2014 15:09:32 +0000 (17:09 +0200)]
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
Commit
497a92308af8e9385fa3d135f7f416a997e4b93b ("ARM: mvebu:
implement L2/PCIe deadlock workaround") introduced some logic in
coherency.c to adjust the PL310 cache controller Device Tree node of
Armada 375 and Armada 38x platform to include the 'arm,io-coherent'
property if the system is running with hardware I/O coherency enabled.
However, with the L2CC driver cleanup done by Russell King, the
initialization of the L2CC driver has been moved earlier, and is now
part of the init_IRQ() ARM function in
arch/arm/kernel/irq.c. Therefore, calling coherency_init() in
->init_time() is now too late, as the Device Tree property gets added
too late (after the L2CC driver has been initialized).
In order to fix this, this commit removes the ->init_time() callback
use in board-v7.c and replaces it with an ->init_irq() callback. We
therefore no longer use the default ->init_irq() callback, but we now
use the default ->init_time() callback.
In this newly introduced ->init_irq() callback, we call irqchip_init()
which is the default behavior when ->init_irq() isn't defined, and
then do the initialization related to the coherency: SCU, coherency
fabric, and mvebu-mbus (which is needed to start secondary CPUs).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 12 Jun 2014 15:09:31 +0000 (17:09 +0200)]
ARM: mvebu: move Armada 375 external abort logic as a quirk
In preparation to a small re-organization of the initialization
sequence in board-v7.c, this commit moves the registration of the
custom external abort handler on Armada 375 later in the boot
sequence, and makes it more similar to the other quirks that we
already have. There is indeed no need to register this abort handler
particularly early, it simply needs to be registered before switching
to userspace.
In addition to this, this commit makes the registration of the custom
abort handler conditional on Armada 375 Z1, because Armada 375 A0 and
later iterations are not affected by the issue.
This commit was tested on both Armada 375 Z1 and Armada 375 A0
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402585772-10405-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Oleg Nesterov [Fri, 27 Jun 2014 17:01:46 +0000 (19:01 +0200)]
tracing/uprobes: Fix the usage of uprobe_buffer_enable() in probe_event_enable()
The usage of uprobe_buffer_enable() added by
dcad1a20 is very wrong,
1. uprobe_buffer_enable() and uprobe_buffer_disable() are not balanced,
_enable() should be called only if !enabled.
2. If uprobe_buffer_enable() fails probe_event_enable() should clear
tp.flags and free event_file_link.
3. If uprobe_register() fails it should do uprobe_buffer_disable().
Link: http://lkml.kernel.org/p/20140627170146.GA18332@redhat.com
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Fixes:
dcad1a204f72 "tracing/uprobes: Fetch args before reserving a ring buffer"
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Fri, 27 Jun 2014 17:01:43 +0000 (19:01 +0200)]
tracing/uprobes: Kill the bogus UPROBE_HANDLER_REMOVE code in uprobe_dispatcher()
I do not know why
dd9fa555d7bb "tracing/uprobes: Move argument fetching
to uprobe_dispatcher()" added the UPROBE_HANDLER_REMOVE, but it looks
wrong.
OK, perhaps it makes sense to avoid store_trace_args() if the tracee is
nacked by uprobe_perf_filter(). But then we should kill the same code
in uprobe_perf_func() and unify the TRACE/PROFILE filtering (we need to
do this anyway to mix perf/ftrace). Until then this code actually adds
the pessimization because uprobe_perf_filter() will be called twice and
return T in likely case.
Link: http://lkml.kernel.org/p/20140627170143.GA18329@redhat.com
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Fri, 27 Jun 2014 17:01:40 +0000 (19:01 +0200)]
uprobes: Change unregister/apply to WARN() if uprobe/consumer is gone
Add WARN_ON's into uprobe_unregister() and uprobe_apply() to ensure
that nobody tries to play with the dead uprobe/consumer. This helps
to catch the bugs like the one fixed by the previous patch.
In the longer term we should fix this poorly designed interface.
uprobe_register() should return "struct uprobe *" which should be
passed to apply/unregister. Plus other semantic changes, see the
changelog in commit
41ccba029e94.
Link: http://lkml.kernel.org/p/20140627170140.GA18322@redhat.com
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Oleg Nesterov [Fri, 27 Jun 2014 17:01:36 +0000 (19:01 +0200)]
tracing/uprobes: Revert "Support mix of ftrace and perf"
This reverts commit
43fe98913c9f67e3b523615ee3316f9520a623e0.
This patch is very wrong. Firstly, this change leads to unbalanced
uprobe_unregister(). Just for example,
# perf probe -x /lib/libc.so.6 syscall
# echo 1 >> /sys/kernel/debug/tracing/events/probe_libc/enable
# perf record -e probe_libc:syscall whatever
after that uprobe is dead (unregistered) but the user of ftrace/perf
can't know this, and it looks as if nobody hits this probe.
This would be easy to fix, but there are other reasons why it is not
simple to mix ftrace and perf. If nothing else, they can't share the
same ->consumer.filter. This is fixable too, but probably we need to
fix the poorly designed uprobe_register() interface first. At least
"register" and "apply" should be clearly separated.
Link: http://lkml.kernel.org/p/20140627170136.GA18319@redhat.com
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: "zhangwei(Jovi)" <jovi.zhangwei@huawei.com>
Cc: stable@vger.kernel.org # v3.14
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Paolo Bonzini [Mon, 30 Jun 2014 14:45:40 +0000 (16:45 +0200)]
Merge commit '
33b458d276bb' into kvm-master
Jan Kiszka [Sun, 29 Jun 2014 15:12:43 +0000 (17:12 +0200)]
KVM: SVM: Fix CPL export via SS.DPL
We import the CPL via SS.DPL since
ae9fedc793. However, we fail to
export it this way so far. This caused spurious guest crashes, e.g. of
Linux when accessing the vmport from guest user space which triggered
register saving/restoring to/from host user space.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jesse Barnes [Wed, 25 Jun 2014 15:24:29 +0000 (08:24 -0700)]
drm/i915: only apply crt_present check on VLV
Apparently we can't trust this field on other platforms and need to find
some other way.
This fixes a regression introduced in
commit
27da3bdfcf7f5233cdfe4563f53edf1ecab7cea0
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Apr 4 16:12:07 2014 -0700
drm/i915: use VBT to determine whether to enumerate the VGA port
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Linus Torvalds [Mon, 30 Jun 2014 02:20:43 +0000 (19:20 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Fix a regression when trying to compile ext4 on older versions gcc.
Fix a number of miscellaneous bugs for punch hole as well as a
long-standing potential double buffer head release when failing a
block allocation for an indirect-mapped file"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Fix hole punching for files with indirect blocks
ext4: Fix block zeroing when punching holes in indirect block files
ext4: decrement free clusters/inodes counters when block group declared bad
fs/mbcache: replace __builtin_log2() with ilog2()
ext4: Fix buffer double free in ext4_alloc_branch()
Linus Torvalds [Sun, 29 Jun 2014 21:11:36 +0000 (14:11 -0700)]
Linux 3.16-rc3
Linus Torvalds [Sun, 29 Jun 2014 20:40:08 +0000 (13:40 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
Randy Dunlap [Sat, 28 Jun 2014 01:28:56 +0000 (18:28 -0700)]
MAINTAINERS: exceptions for Documentation maintainer
Note that I don't maintain Documentation/ABI/,
Documentation/devicetree/, or the language translation files.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Sat, 28 Jun 2014 01:28:46 +0000 (18:28 -0700)]
Documentation: add section about git to email-clients.txt
These days most people use git to send patches so I have added a section
about that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Kroah-Hartman [Sun, 29 Jun 2014 16:43:23 +0000 (09:43 -0700)]
Merge tag 'iio-fixes-for-3.16b' of git://git./linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 3.16 cycle.
* A fix for a bug in setting threshold levels within the ad799x driver
which prevents correct setting of the thresholds.
* In ad7291 fix an case where a ERR_PTR value was returned directly
instead of having PTR_ERR applied. Hence it would report success
instead of failure.
* of_iio_channel_get_by_name returned a non null pointer if it fails
and the callee was expecting NULL to indicate failure. Fixed by
returning NULL in the error cases.
Will Deacon [Fri, 27 Jun 2014 16:01:47 +0000 (17:01 +0100)]
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.
This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Laura Abbott [Fri, 27 Jun 2014 09:17:27 +0000 (10:17 +0100)]
ARM: 8086/1: Set memblock limit for nommu
Commit
1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrea Adami [Wed, 25 Jun 2014 21:32:26 +0000 (22:32 +0100)]
ARM: 8085/1: sa1100: collie: add top boot mtd partition
The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrea Adami [Wed, 25 Jun 2014 21:31:15 +0000 (22:31 +0100)]
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
Reverts commit
d26b17edafc45187c30cae134a5e5429d58ad676
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.
Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Nicolas Pitre [Thu, 19 Jun 2014 21:57:01 +0000 (22:57 +0100)]
ARM: 8080/1: mcpm.h: remove unused variable declaration
The sync_phys variable has been replaced by link time computation in
mcpm_head.S before the code was submitted upstream.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thomas Petazzoni [Fri, 13 Jun 2014 09:58:38 +0000 (10:58 +0100)]
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Josef Bacik [Wed, 25 Jun 2014 20:45:41 +0000 (13:45 -0700)]
btrfs: only unlock block in verify_parent_transid if we locked it
This is a regression from my patch
a26e8c9f75b0bfd8cccc9e8f110737b136eb5994, we
need to only unlock the block if we were the one who locked it. Otherwise this
will trip BUG_ON()'s in locking.c Thanks,
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Filipe Manana [Tue, 24 Jun 2014 16:48:28 +0000 (17:48 +0100)]
Btrfs: assert send doesn't attempt to start transactions
When starting a transaction just assert that current->journal_info
doesn't contain a send transaction stub, since send isn't supposed
to start transactions and when it finishes (either successfully or
not) it's supposed to set current->journal_info to NULL.
This is motivated by the change titled:
Btrfs: fix crash when starting transaction
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Sergey Senozhatsky [Tue, 24 Jun 2014 15:00:44 +0000 (00:00 +0900)]
btrfs compression: reuse recently used workspace
Add compression `workspace' in free_workspace() to
`idle_workspace' list head, instead of tail. So we have
better chances to reuse most recently used `workspace'.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Liu Bo [Tue, 24 Jun 2014 07:39:16 +0000 (15:39 +0800)]
Btrfs: fix crash when mounting raid5 btrfs with missing disks
The reproducer is
$ mkfs.btrfs D1 D2 D3 -mraid5
$ mkfs.ext4 D2 && mkfs.ext4 D3
$ mount D1 /btrfs -odegraded
-------------------
[ 87.672992] ------------[ cut here ]------------
[ 87.673845] kernel BUG at fs/btrfs/raid56.c:1828!
...
[ 87.673845] RIP: 0010:[<
ffffffff813efc7e>] [<
ffffffff813efc7e>] __raid_recover_end_io+0x4ae/0x4d0
...
[ 87.673845] Call Trace:
[ 87.673845] [<
ffffffff8116bbc6>] ? mempool_free+0x36/0xa0
[ 87.673845] [<
ffffffff813f0255>] raid_recover_end_io+0x75/0xa0
[ 87.673845] [<
ffffffff81447c5b>] bio_endio+0x5b/0xa0
[ 87.673845] [<
ffffffff81447cb2>] bio_endio_nodec+0x12/0x20
[ 87.673845] [<
ffffffff81374621>] end_workqueue_fn+0x41/0x50
[ 87.673845] [<
ffffffff813ad2aa>] normal_work_helper+0xca/0x2c0
[ 87.673845] [<
ffffffff8108ba2b>] process_one_work+0x1eb/0x530
[ 87.673845] [<
ffffffff8108b9c9>] ? process_one_work+0x189/0x530
[ 87.673845] [<
ffffffff8108c15b>] worker_thread+0x11b/0x4f0
[ 87.673845] [<
ffffffff8108c040>] ? rescuer_thread+0x290/0x290
[ 87.673845] [<
ffffffff810939c4>] kthread+0xe4/0x100
[ 87.673845] [<
ffffffff810938e0>] ? kthread_create_on_node+0x220/0x220
[ 87.673845] [<
ffffffff817e7c7c>] ret_from_fork+0x7c/0xb0
[ 87.673845] [<
ffffffff810938e0>] ? kthread_create_on_node+0x220/0x220
-------------------
It's because that we miscalculate @rbio->bbio->error so that it doesn't
reach maximum of tolerable errors while it should have.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Satoru Takeuchi<takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Anand Jain [Tue, 3 Jun 2014 03:36:03 +0000 (11:36 +0800)]
btrfs: create sprout should rename fsid on the sysfs as well
Creating sprout will change the fsid of the mounted root.
do the same on the sysfs as well.
reproducer:
mount /dev/sdb /btrfs (seed disk)
btrfs dev add /dev/sdc /btrfs
mount -o rw,remount /btrfs
btrfs dev del /dev/sdb /btrfs
mount /dev/sdb /btrfs
Error:
kobject_add_internal failed for
fe350492-dc28-4051-a601-
e017b17e6145 with -EEXIST, don't try to register things with the same name in the same directory.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Anand Jain [Tue, 3 Jun 2014 03:36:02 +0000 (11:36 +0800)]
btrfs: dev replace should replace the sysfs entry
when we replace the device its corresponding sysfs
entry has to be replaced as well
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Anand Jain [Tue, 3 Jun 2014 03:36:01 +0000 (11:36 +0800)]
btrfs: dev add should add its sysfs entry
we would need the device links to be created,
when device is added.
Signed-off-by: Anand Jain <Anand.Jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Anand Jain [Tue, 3 Jun 2014 03:36:00 +0000 (11:36 +0800)]
btrfs: dev delete should remove sysfs entry
when we delete the device from the mounted btrfs,
we would need its corresponding sysfs enty to
be removed as well.
Signed-off-by: Anand Jain <Anand.Jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Anand Jain [Tue, 3 Jun 2014 03:35:59 +0000 (11:35 +0800)]
btrfs: rename add_device_membership to btrfs_kobj_add_device
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Linus Torvalds [Sat, 28 Jun 2014 18:32:32 +0000 (11:32 -0700)]
Merge tag 'spi-v3.16-rc2' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the biggest one being a fix for the newly
added Qualcomm SPI controller driver to make it not use its internal
chip select due to hardware bugs, replacing it with GPIOs"
* tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Remove chip select function
spi: qup: Fix order of spi_register_master
spi: sh-sci: fix use-after-free in sh_sci_spi_remove()
spi/pxa2xx: fix incorrect SW mode chipselect setting for BayTrail LPSS SPI
Linus Torvalds [Sat, 28 Jun 2014 18:31:58 +0000 (11:31 -0700)]
Merge tag 'regulator-v3.16-rc2' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Several driver specific fixes here, the palmas fixes being especially
important for a range of boards - the recent updates to support new
devices have introduced several regressions"
* tag 'regulator-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65218: Correct the the config register for LDO1
regulator: tps65218: Add the missing of_node assignment in probe
regulator: palmas: fix typo in enable_reg calculation
regulator: bcm590xx: fix vbus name
regulator: palmas: Fix SMPS enable/disable/is_enabled
Linus Torvalds [Sat, 28 Jun 2014 16:43:58 +0000 (09:43 -0700)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time around. The highlights include:
- iscsi-target CHAP authentication fixes to enforce explicit key
values (Tejas Vaykole + rahul.rane)
- fix a long-standing OOPs in target-core when a alua configfs
attribute is accessed after port symlink has been removed.
(Sebastian Herbszt)
- fix a v3.10.y iscsi-target regression causing the login reject
status class/detail to be ignored (Christoph Vu-Brugier)
- fix a v3.10.y iscsi-target regression to avoid rejecting an
existing ITT during Data-Out when data-direction is wrong (Santosh
Kulkarni + Arshad Hussain)
- fix a iscsi-target related shutdown deadlock on UP kernels (Mikulas
Patocka)
- fix a v3.16-rc1 build issue with vhost-scsi + !CONFIG_NET (MST)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: fix iscsit_del_np deadlock on unload
iovec: move memcpy_from/toiovecend to lib/iovec.c
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
iscsi-target: Explicily clear login response PDU in exception path
target: Fix left-over se_lun->lun_sep pointer OOPs
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
Mark Brown [Sat, 28 Jun 2014 13:01:23 +0000 (14:01 +0100)]
Merge remote-tracking branches 'spi/fix/pxa2xx', 'spi/fix/qup' and 'spi/fix/sh-sci' into spi-linus
Mark Brown [Sat, 28 Jun 2014 13:01:04 +0000 (14:01 +0100)]
Merge remote-tracking branches 'regulator/fix/bcm590xx', 'regulator/fix/palmas' and 'regulator/fix/tps65218' into regulator-linus
Mikulas Patocka [Mon, 23 Jun 2014 17:42:37 +0000 (13:42 -0400)]
iscsi-target: fix iscsit_del_np deadlock on unload
On uniprocessor preemptible kernel, target core deadlocks on unload. The
following events happen:
* iscsit_del_np is called
* it calls send_sig(SIGINT, np->np_thread, 1);
* the scheduler switches to the np_thread
* the np_thread is woken up, it sees that kthread_should_stop() returns
false, so it doesn't terminate
* the np_thread clears signals with flush_signals(current); and goes back
to sleep in iscsit_accept_np
* the scheduler switches back to iscsit_del_np
* iscsit_del_np calls kthread_stop(np->np_thread);
* the np_thread is waiting in iscsit_accept_np and it doesn't respond to
kthread_stop
The deadlock could be resolved if the administrator sends SIGINT signal to
the np_thread with killall -INT iscsi_np
The reproducible deadlock was introduced in commit
db6077fd0b7dd41dc6ff18329cec979379071f87, but the thread-stopping code was
racy even before.
This patch fixes the problem. Using kthread_should_stop to stop the
np_thread is unreliable, so we test np_thread_state instead. If
np_thread_state equals ISCSI_NP_THREAD_SHUTDOWN, the thread exits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Sat, 28 Jun 2014 02:00:45 +0000 (19:00 -0700)]
Merge tag 'iommu-fixes-v3.16-rc1' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- fix VT-d regression with handling multiple RMRR entries per device
- fix a small race that was left in the mmu_notifier handling in the
AMD IOMMUv2 driver
* tag 'iommu-fixes-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix small race between invalidate_range_end/start
iommu/vt-d: fix bug in handling multiple RMRRs for the same PCI device
Linus Torvalds [Sat, 28 Jun 2014 01:43:03 +0000 (18:43 -0700)]
Merge branch 'x86/urgent' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A pile of fixes related to the VDSO, EFI and 32-bit badsys handling.
It turns out that removing the section headers from the VDSO breaks
gdb, so this puts back most of them. A very simple typo broke
rt_sigreturn on some versions of glibc, with obviously disastrous
results. The rest is pretty much fixes for the corresponding fallout.
The EFI fixes fixes an arithmetic overflow on 32-bit systems and
quiets some build warnings.
Finally, when invoking an invalid system call number on x86-32, we
bypass a bunch of handling, which can make the audit code oops"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi-pstore: Fix an overflow on 32-bit builds
x86/vdso: Error out in vdso2c if DT_RELA is present
x86/vdso: Move DISABLE_BRANCH_PROFILING into the vdso makefile
x86_32, signal: Fix vdso rt_sigreturn
x86_32, entry: Do syscall exit work on badsys (CVE-2014-4508)
x86/vdso: Create .build-id links for unstripped vdso files
x86/vdso: Remove some redundant in-memory section headers
x86/vdso: Improve the fake section headers
x86/vdso2c: Use better macros for ELF bitness
x86/vdso: Discard the __bug_table section
efi: Fix compiler warnings (unused, const, type)
Linus Torvalds [Sat, 28 Jun 2014 01:37:56 +0000 (18:37 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"This is dominated by a large number of changes necessary for the MIPS
BPF code. code. Aside of that there are
- a fix for the MSC system controller support code.
- a Turbochannel fix.
- a recordmcount fix that's MIPS-specific.
- barrier fixes to smp-cps / pm-cps after unrelated changes elsewhere
in the kernel.
- revert support for MSA registers in the signal frames. The
reverted patch did modify the signal stack frame which of course is
inacceptable.
- fix math-emu build breakage with older compilers.
- some related cleanup.
- fix Lasat build error if CONFIG_CRC32 isn't set to y by the user"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (27 commits)
MIPS: Lasat: Fix build error if CRC32 is not enabled.
TC: Handle device_register() errors.
MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region
MIPS: bpf: Fix stack space allocation for BPF memwords on MIPS64
MIPS: BPF: Use 32 or 64-bit load instruction to load an address to register
MIPS: bpf: Fix PKT_TYPE case for big-endian cores
MIPS: BPF: Prevent kernel fall over for >=32bit shifts
MIPS: bpf: Drop update_on_xread and always initialize the X register
MIPS: bpf: Fix is_range() semantics
MIPS: bpf: Use pr_debug instead of pr_warn for unhandled opcodes
MIPS: bpf: Fix return values for VLAN_TAG_PRESENT case
MIPS: bpf: Use correct mask for VLAN_TAG case
MIPS: bpf: Fix branch conditional for BPF_J{GT/GE} cases
MIPS: bpf: Add SEEN_SKB to flags when looking for the PKT_TYPE
MIPS: bpf: Use 'andi' instead of 'and' for the VLAN cases
MIPS: bpf: Return error code if the offset is a negative number
MIPS: bpf: Use the LO register to get division's quotient
MIPS: mm: uasm: Fix lh micro-assembler instruction
MIPS: uasm: Add SLT uasm instruction
MIPS: uasm: Add s3s1s2 instruction builder
...
Linus Torvalds [Sat, 28 Jun 2014 01:36:50 +0000 (18:36 -0700)]
Merge tag 'arc-fixes-for-3.16' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Some SMP changes, a ptrace request for NPTL debugging, bunch of build
breakages/warnings"
* tag 'arc-fixes-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [SMP] Enable icache coherency
ARC: [SMP] Fix IPI IRQ registration
ARC: Implement ptrace(PTRACE_GET_THREAD_AREA)
ARC: optimize kernel bss clearing in early boot code
ARC: Fix build breakage for !CONFIG_ARC_DW2_UNWIND
ARC: fix build warning in devtree
ARC: remove checks for CONFIG_ARC_MMU_V4
Linus Torvalds [Sat, 28 Jun 2014 01:33:49 +0000 (18:33 -0700)]
Merge tag 'compress-3.16-rc3' of git://git./linux/kernel/git/gregkh/driver-core
Pull compress bugfix from Greg KH:
"Here is another lz4 bugfix for 3.16-rc3 that resolves a reported issue
with that compression algorithm"
* tag 'compress-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lz4: fix another possible overrun
Linus Torvalds [Sat, 28 Jun 2014 01:04:22 +0000 (18:04 -0700)]
Merge tag 'stable/for-linus-3.16-rc1-tag' of git://git./linux/kernel/git/konrad/swiotlb
Pull swiotlb bugfix from Konrad Rzeszutek Wilk:
"One bug-fix that had been in tree for quite some time. We had assumed
that the physical address zero was invalid and would fail it. But
that is not true and on some architectures it is not reserved and
valid. This fixes it"
* tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: don't assume PA 0 is invalid
Linus Torvalds [Sat, 28 Jun 2014 00:21:36 +0000 (17:21 -0700)]
Merge tag 'sound-3.16-rc3' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here includes a few patchset for fixing mostly HD-audio issues in
addition to a patch assuring the compress API bytes alignment and a
fix for the die-hard existing race condition at USB-audio
disconnection. The volume looks big in Realtek HD-audio code, but
it's just a translation of the fixup tables, and the actual changes
are rather trivial"
* tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N values when resuming HSW/BDW display controller
ALSA: usb-audio: Fix races at disconnection and PCM closing
ALSA: hda - Adjust speaker HPF and add LED support for HP Spectre 13
ALSA: hda - Make the pin quirk tables use the SND_HDA_PIN_QUIRK macro
ALSA: hda - Make a SND_HDA_PIN_QUIRK macro
ALSA: hda - Add pin quirk for Dell XPS 15
ALSA: hda - hdmi: call overridden init on resume
ALSA: hda - Fix usage of "model" module parameter
ALSA: compress: fix the struct alignment to 4 bytes
Linus Torvalds [Sat, 28 Jun 2014 00:20:48 +0000 (17:20 -0700)]
Merge tag 'mfd-fixes-3.16' of git://git./linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Couple of simple fixes due for the v3.16 -rcs"
* tag 'mfd-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: ab8500: Fix dt irq mapping
mfd: davinci: Voicecodec needs regmap_mmio
mfd: STw481x: Allow modular build
mfd: UCB1x00: Enable modular build
Linus Torvalds [Sat, 28 Jun 2014 00:05:39 +0000 (17:05 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Exynos, i915 and msm fixes and one core fix.
exynos:
hdmi power off and mixer issues
msm:
iommu, build fixes,
i915:
regression races and warning fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
drm: fix NULL pointer access by wrong ioctl
drm/exynos: enable vsync interrupt while waiting for vblank
drm/exynos: soft reset mixer before reconfigure after power-on
drm/exynos: allow multiple layer updates per vsync for mixer
drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
drm/i915: BDW: Adding Reserved PCI IDs.
drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
drm/exynos: stop mixer before gating clocks during poweroff
drm/exynos: set power state variable after enabling clocks and power
drm/exynos: disable unused windows on apply
drm/exynos: Fix de-registration ordering
drm/exynos: change zero to NULL for sparse
drm/exynos: dpi: Fix NULL pointer dereference with legacy bindings
drm/exynos: hdmi: fix power order issue
drm/i915: default to having backlight if VBT not available
drm/i915: cache hw power well enabled state
drm/msm: fix IOMMU cleanup for -EPROBE_DEFER
drm/msm: use PAGE_ALIGNED instead of IS_ALIGNED(PAGE_SIZE)
drm/msm/hdmi: set hdp clock rate before prepare_enable
...
J. Bruce Fields [Thu, 19 Jun 2014 20:44:48 +0000 (16:44 -0400)]
nfsd: fix rare symlink decoding bug
An NFS operation that creates a new symlink includes the symlink data,
which is xdr-encoded as a length followed by the data plus 0 to 3 bytes
of zero-padding as required to reach a 4-byte boundary.
The vfs, on the other hand, wants null-terminated data.
The simple way to handle this would be by copying the data into a newly
allocated buffer with space for the final null.
The current nfsd_symlink code tries to be more clever by skipping that
step in the (likely) case where the byte following the string is already
0.
But that assumes that the byte following the string is ours to look at.
In fact, it might be the first byte of a page that we can't read, or of
some object that another task might modify.
Worse, the NFSv4 code tries to fix the problem by actually writing to
that byte.
In the NFSv2/v3 cases this actually appears to be safe:
- nfs3svc_decode_symlinkargs explicitly null-terminates the data
(after first checking its length and copying it to a new
page).
- NFSv2 limits symlinks to 1k. The buffer holding the rpc
request is always at least a page, and the link data (and
previous fields) have maximum lengths that prevent the request
from reaching the end of a page.
In the NFSv4 case the CREATE op is potentially just one part of a long
compound so can end up on the end of a page if you're unlucky.
The minimal fix here is to copy and null-terminate in the NFSv4 case.
The nfsd_symlink() interface here seems too fragile, though. It should
really either do the copy itself every time or just require a
null-terminated string.
Reported-by: Jeff Layton <jlayton@primarydata.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Michael S. Tsirkin [Thu, 19 Jun 2014 18:22:56 +0000 (21:22 +0300)]
iovec: move memcpy_from/toiovecend to lib/iovec.c
ERROR: "memcpy_fromiovecend" [drivers/vhost/vhost_scsi.ko] undefined!
commit
9f977ef7b671f6169eca78bf40f230fe84b7c7e5
vhost-scsi: Include prot_bytes into expected data transfer length
in target-pending makes drivers/vhost/scsi.c call memcpy_fromiovecend().
This function is not available when CONFIG_NET is not enabled.
socket.h already includes uio.h, so no callers need updating.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Fri, 20 Jun 2014 17:59:57 +0000 (10:59 -0700)]
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
This patch changes iscsit_check_dataout_hdr() to dump the incoming
Data-Out payload when the received ITT is not associated with a
WRITE, instead of calling iscsit_reject_cmd() for the non WRITE
ITT descriptor.
This addresses a bug where an initiator sending an Data-Out for
an ITT associated with a READ would end up generating a reject
for the READ, eventually resulting in list corruption.
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Greg Kroah-Hartman [Tue, 24 Jun 2014 20:59:01 +0000 (16:59 -0400)]
lz4: fix another possible overrun
There is one other possible overrun in the lz4 code as implemented by
Linux at this point in time (which differs from the upstream lz4
codebase, but will get synced at in a future kernel release.) As
pointed out by Don, we also need to check the overflow in the data
itself.
While we are at it, replace the odd error return value with just a
"simple" -1 value as the return value is never used for anything other
than a basic "did this work or not" check.
Reported-by: "Don A. Bailey" <donb@securitymouse.com>
Reported-by: Willy Tarreau <w@1wt.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 27 Jun 2014 17:42:05 +0000 (10:42 -0700)]
Merge tag 'usb-serial-3.16-rc3' of git://git./linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.16-rc3
Here are some USB-serial updates for v3.16-rc3 that fix a reported
NULL-pointer dereference and add some new device IDs.
Included is also two changes to MAINTAINERS dropping individual
maintainership for two small sub-drivers and updating an email address.
Signed-off-by: Johan Hovold <johan@kernel.org>
Thomas Gleixner [Fri, 20 Jun 2014 21:41:24 +0000 (23:41 +0200)]
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
Some TI chips raise the DMA complete interrupt before the actual
transfer has been completed. The code tries to busy wait for a few
microseconds and if that fails it arms an hrtimer to recheck. So far
so good, but that has the following issue:
CPU 0 CPU1
start_next_transfer(RQ1);
DMA interrupt
if (premature_irq(RQ1))
if (!hrtimer_active(timer))
hrtimer_start(timer);
hrtimer expires
timer->state = CALLBACK_RUNNING;
timer->fn()
cppi41_recheck_tx_req()
complete_request(RQ1);
if (requests_pending())
start_next_transfer(RQ2);
DMA interrupt
if (premature_irq(RQ2))
if (!hrtimer_active(timer))
hrtimer_start(timer);
timer->state = INACTIVE;
The premature interrupt of request2 on CPU1 does not arm the timer and
therefor the request completion never happens because it checks for
!hrtimer_active(). hrtimer_active() evaluates:
timer->state != HRTIMER_STATE_INACTIVE
which of course evaluates to true in the above case as timer->state is
CALLBACK_RUNNING.
That's clearly documented:
* A timer is active, when it is enqueued into the rbtree or the
* callback function is running or it's in the state of being migrated
* to another cpu.
But that's not what the code wants to check. The code wants to check
whether the timer is queued, i.e. whether its armed and waiting for
expiry.
We have a helper function for this: hrtimer_is_queued(). This
evaluates:
timer->state & HRTIMER_STATE_QUEUED
So in the above case this evaluates to false and therefor forces the
DMA interrupt on CPU1 to call hrtimer_start().
Use hrtimer_is_queued() instead of hrtimer_active() and evrything is
good.
Reported-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Andreas Larsson [Thu, 26 Jun 2014 11:07:48 +0000 (13:07 +0200)]
usb: gadget: gr_udc: Fix check for invalid number of microframes
The value 0x3 (not 0x11) in the field for additional transaction/microframe
is reserved and should not be let through. Be clear in the error message about
what value caused the error return.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Ezequiel Garcia [Mon, 23 Jun 2014 18:34:22 +0000 (15:34 -0300)]
usb: musb: Fix panic upon musb_am335x module removal
At probe time, the musb_am335x driver register its childs by
calling of_platform_populate(), which registers all childs in
the devicetree hierarchy recursively.
On the other side, the driver's remove() function uses of_device_unregister()
to remove each child of musb_am335x's.
However, when musb_dsps is loaded, its devices are attached to the musb_am335x
device as musb_am335x childs. Hence, musb_am335x remove() will attempt to
unregister the devices registered by musb_dsps, which produces a kernel panic.
In other words, the childs in the "struct device" hierarchy are not the same
as the childs in the "devicetree" hierarchy.
Ideally, we should enforce the removal of the devices registered by
musb_am335x *only*, instead of all its child devices. However, because of the
recursive nature of of_platform_populate, this doesn't seem possible.
Therefore, as the only solution at hand, this commit disables musb_am335x
driver removal capability, preventing it from being ever removed. This was
originally suggested by Sebastian Siewior:
https://www.mail-archive.com/linux-omap@vger.kernel.org/msg104946.html
And for reference, here's the panic upon module removal:
musb-hdrc musb-hdrc.0.auto: remove, state 4
usb usb1: USB disconnect, device number 1
musb-hdrc musb-hdrc.0.auto: USB bus 1 deregistered
Unable to handle kernel NULL pointer dereference at virtual address
0000008c
pgd =
de11c000
[
0000008c] *pgd=
9e174831, *pte=
00000000, *ppte=
00000000
Internal error: Oops: 17 [#1] ARM
Modules linked in: musb_am335x(-) musb_dsps musb_hdrc usbcore usb_common
CPU: 0 PID: 623 Comm: modprobe Not tainted
3.15.0-rc4-00001-g24efd13 #69
task:
de1b7500 ti:
de122000 task.ti:
de122000
PC is at am335x_shutdown+0x10/0x28
LR is at am335x_shutdown+0xc/0x28
pc : [<
c0327798>] lr : [<
c0327794>] psr:
a0000013
sp :
de123df8 ip :
00000004 fp :
00028f00
r10:
00000000 r9 :
de122000 r8 :
c000e6c4
r7 :
de0e3c10 r6 :
de0e3800 r5 :
de624010 r4 :
de1ec750
r3 :
de0e3810 r2 :
00000000 r1 :
00000001 r0 :
00000000
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control:
10c5387d Table:
9e11c019 DAC:
00000015
Process modprobe (pid: 623, stack limit = 0xde122240)
Stack: (0xde123df8 to 0xde124000)
3de0:
de0e3810 bf054488
3e00:
bf05444c de624010 60000013 bf043650 000012fc de624010 de0e3810 bf043a20
3e20:
de0e3810 bf04b240 c0635b88 c02ca37c c02ca364 c02c8db0 de1b7500 de0e3844
3e40:
de0e3810 c02c8e28 c0635b88 de02824c de0e3810 c02c884c de0e3800 de0e3810
3e60:
de0e3818 c02c5b20 bf05417c de0e3800 de0e3800 c0635b88 de0f2410 c02ca838
3e80:
bf05417c de0e3800 bf055438 c02ca8cc de0e3c10 bf054194 de0e3c10 c02ca37c
3ea0:
c02ca364 c02c8db0 de1b7500 de0e3c44 de0e3c10 c02c8e28 c0635b88 de02824c
3ec0:
de0e3c10 c02c884c de0e3c10 de0e3c10 de0e3c18 c02c5b20 de0e3c10 de0e3c10
3ee0:
00000000 bf059000 a0000013 c02c5bc0 00000000 bf05900c de0e3c10 c02c5c48
3f00:
de0dd0c0 de1ec970 de0f2410 bf05929c de0f2444 bf05902c de0f2410 c02ca37c
3f20:
c02ca364 c02c8db0 bf05929c de0f2410 bf05929c c02c94c8 bf05929c 00000000
3f40:
00000800 c02c8ab4 bf0592e0 c007fc40 c00dd820 6273756d 336d615f 00783533
3f60:
c064a0ac de1b7500 de122000 de1b7500 c000e590 00000001 c000e6c4 c0060160
3f80:
00028e70 00028e70 00028ea4 00000081 60000010 00028e70 00028e70 00028ea4
3fa0:
00000081 c000e500 00028e70 00028e70 00028ea4 00000800 becb59f8 00027608
3fc0:
00028e70 00028e70 00028ea4 00000081 00000001 00000001 00000000 00028f00
3fe0:
b6e6b6f0 becb59d4 000160e8 b6e6b6fc 60000010 00028ea4 00000000 00000000
[<
c0327798>] (am335x_shutdown) from [<
bf054488>] (dsps_musb_exit+0x3c/0x4c [musb_dsps])
[<
bf054488>] (dsps_musb_exit [musb_dsps]) from [<
bf043650>] (musb_shutdown+0x80/0x90 [musb_hdrc])
[<
bf043650>] (musb_shutdown [musb_hdrc]) from [<
bf043a20>] (musb_remove+0x24/0x68 [musb_hdrc])
[<
bf043a20>] (musb_remove [musb_hdrc]) from [<
c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<
c02ca37c>] (platform_drv_remove) from [<
c02c8db0>] (__device_release_driver+0x70/0xc8)
[<
c02c8db0>] (__device_release_driver) from [<
c02c8e28>] (device_release_driver+0x20/0x2c)
[<
c02c8e28>] (device_release_driver) from [<
c02c884c>] (bus_remove_device+0xdc/0x10c)
[<
c02c884c>] (bus_remove_device) from [<
c02c5b20>] (device_del+0x104/0x198)
[<
c02c5b20>] (device_del) from [<
c02ca838>] (platform_device_del+0x14/0x9c)
[<
c02ca838>] (platform_device_del) from [<
c02ca8cc>] (platform_device_unregister+0xc/0x20)
[<
c02ca8cc>] (platform_device_unregister) from [<
bf054194>] (dsps_remove+0x18/0x38 [musb_dsps])
[<
bf054194>] (dsps_remove [musb_dsps]) from [<
c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<
c02ca37c>] (platform_drv_remove) from [<
c02c8db0>] (__device_release_driver+0x70/0xc8)
[<
c02c8db0>] (__device_release_driver) from [<
c02c8e28>] (device_release_driver+0x20/0x2c)
[<
c02c8e28>] (device_release_driver) from [<
c02c884c>] (bus_remove_device+0xdc/0x10c)
[<
c02c884c>] (bus_remove_device) from [<
c02c5b20>] (device_del+0x104/0x198)
[<
c02c5b20>] (device_del) from [<
c02c5bc0>] (device_unregister+0xc/0x20)
[<
c02c5bc0>] (device_unregister) from [<
bf05900c>] (of_remove_populated_child+0xc/0x14 [musb_am335x])
[<
bf05900c>] (of_remove_populated_child [musb_am335x]) from [<
c02c5c48>] (device_for_each_child+0x44/0x70)
[<
c02c5c48>] (device_for_each_child) from [<
bf05902c>] (am335x_child_remove+0x18/0x30 [musb_am335x])
[<
bf05902c>] (am335x_child_remove [musb_am335x]) from [<
c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<
c02ca37c>] (platform_drv_remove) from [<
c02c8db0>] (__device_release_driver+0x70/0xc8)
[<
c02c8db0>] (__device_release_driver) from [<
c02c94c8>] (driver_detach+0xb4/0xb8)
[<
c02c94c8>] (driver_detach) from [<
c02c8ab4>] (bus_remove_driver+0x4c/0xa0)
[<
c02c8ab4>] (bus_remove_driver) from [<
c007fc40>] (SyS_delete_module+0x128/0x1cc)
[<
c007fc40>] (SyS_delete_module) from [<
c000e500>] (ret_fast_syscall+0x0/0x48)
Fixes:
97238b35d5bb ("usb: musb: dsps: use proper child nodes")
Cc: <stable@vger.kernel.org> # v3.12+
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Michal Nazarewicz [Fri, 13 Jun 2014 13:38:04 +0000 (15:38 +0200)]
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Even though usb_functionfs_descs_head structure is now deprecated,
it has been used by some user space tools. Its removel in commit
[
ac8dde1: “Add flags to descriptors block”] was an oversight
leading to build breakage for such tools.
Bring it back so that old user space tools can still be build
without problems on newer kernel versions.
Cc: <stable@vger.kernel.org> # 3.14
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reported-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Fri, 27 Jun 2014 15:41:00 +0000 (10:41 -0500)]
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
This reverts commit
f2af74123f8c5a735248547f4286a3adc28633c1.
There is a better fix for this build error coming in a following
patch.
Signed-of-by: Felipe Balbi <balbi@ti.com>
H. Peter Anvin [Fri, 27 Jun 2014 14:55:24 +0000 (07:55 -0700)]
Merge tag 'efi-urgent' into x86/urgent
* Fix a few compiler warnings (one being a real bug) in the arm64 EFI
code that lots of people are running into and reporting - Catalin Marinas
* Use a cast to avoid a 32-bit overflow issue when generating pstore
filenames - Andrzej Zaborowski
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Ville Syrjälä [Tue, 24 Jun 2014 10:59:28 +0000 (13:59 +0300)]
drm/i915: Wait for vblank after enabling the primary plane on BDW
BDW signals the flip done interrupt immediately after the DSPSURF write
when the plane is disabled. This is true even if we've already armed
DSPCNTR to enable the plane at the next vblank. This causes major
problems for our page flip code which relies on the flip done interrupts
happening at vblank time.
So what happens is that we enable the plane, and immediately allow
userspace to submit a page flip. If the plane is still in the process
of being enabled when the page flip is issued, the flip done gets
signalled immediately. Our DSPSURFLIVE check catches this to prevent
premature flip completion, but it also means that we don't get a flip
done interrupt when the plane actually gets enabled, and so the page
flip is never completed.
Work around this by re-introducing blocking vblank waits on BDW
whenever we enable the primary plane.
I removed some of the vblank waits here:
commit
6304cd91e7f05f8802ea6f91287cac09741d9c46
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Apr 25 13:30:12 2014 +0300
drm/i915: Drop the excessive vblank waits from modeset codepaths
To avoid these blocking vblank waits we should start using the vblank
interrupt instead of the flip done interrupt to complete page flips.
But that's material for another patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79354
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Paolo Bonzini [Fri, 27 Jun 2014 14:19:39 +0000 (16:19 +0200)]
Merge tag 'kvms390-
20140626' of git://git./linux/kernel/git/kvms390/linux into kvm-master
Fix sie.h header related problems introduced during the 3.16 development
cycle.
Takashi Iwai [Fri, 27 Jun 2014 10:14:35 +0000 (12:14 +0200)]
ALSA: hda - Add a fixup for Thinkpad T540p
The similar fixup as T440 is needed for supporting the dock on T540.
Reported-by: Jim Minter <jminter@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
David Henningsson [Fri, 27 Jun 2014 06:41:59 +0000 (08:41 +0200)]
ALSA: hda - Add another headset pin quirk for some Dell machines
Another quirk to make the headset mic work on some new Dell machines.
Cc: Hui Wang <hui.wang@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1297581
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Andrzej Zaborowski [Mon, 9 Jun 2014 14:50:40 +0000 (16:50 +0200)]
efi-pstore: Fix an overflow on 32-bit builds
In generic_id the long int timestamp is multiplied by 100000 and needs
an explicit cast to u64.
Without that the id in the resulting pstore filename is wrong and
userspace may have problems parsing it, but more importantly files in
pstore can never be deleted and may fill the EFI flash (brick device?).
This happens because when generic pstore code wants to delete a file,
it passes the id to the EFI backend which reinterpretes it and a wrong
variable name is attempted to be deleted. There's no error message but
after remounting pstore, deleted files would reappear.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Olof Johansson [Fri, 27 Jun 2014 06:10:55 +0000 (23:10 -0700)]
ARM: bcm: Fix bcm and multi_v7 defconfigs
BCM (Kona/capri platform) has regressed in two ways on this release. First,
bcm_defconfig no longer selected the appropriate MMC driver options due to
changes in dependencies. Secondly, the new MFD and regulator drivers were not
enabled on multi_v7_defconfig, so that caused the system to fail probing MMC
there.
Fix by enabling the new options as needed.
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Dave Airlie [Fri, 27 Jun 2014 05:04:06 +0000 (15:04 +1000)]
Merge tag 'drm-intel-fixes-2014-06-26' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Fixes for 3.16-rc2; regressions, races, and warns; Broadwell PCI IDs.
* tag 'drm-intel-fixes-2014-06-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
drm/i915: BDW: Adding Reserved PCI IDs.
drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
drm/i915: default to having backlight if VBT not available
drm/i915: cache hw power well enabled state
Nicholas Bellinger [Tue, 17 Jun 2014 22:23:03 +0000 (22:23 +0000)]
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
This patch fixes a tcm_loop_cmd descriptor memory leak in the
tcm_loop_submission_work() error path, and would result in
warnings about leaked tcm_loop_cmd_cache objects at module
unload time.
Go ahead and invoke kmem_cache_free() to release tl_cmd back to
tcm_loop_cmd_cache before calling sc->scsi_done().
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Tue, 17 Jun 2014 21:54:38 +0000 (21:54 +0000)]
iscsi-target: Explicily clear login response PDU in exception path
This patch adds a explicit memset to the login response PDU
exception path in iscsit_tx_login_rsp().
This addresses a regression bug introduced in commit
baa4d64b
where the initiator would end up not receiving the login
response and associated status class + detail, before closing
the login connection.
Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Mon, 16 Jun 2014 20:25:54 +0000 (20:25 +0000)]
target: Fix left-over se_lun->lun_sep pointer OOPs
This patch fixes a left-over se_lun->lun_sep pointer OOPs when one
of the /sys/kernel/config/target/$FABRIC/$WWPN/$TPGT/lun/$LUN/alua*
attributes is accessed after the $DEVICE symlink has been removed.
To address this bug, go ahead and clear se_lun->lun_sep memory in
core_dev_unexport(), so that the existing checks for show/store
ALUA attributes in target_core_fabric_configfs.c work as expected.
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Fri, 13 Jun 2014 04:28:31 +0000 (04:28 +0000)]
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
This patch adds a check in chap_server_compute_md5() to enforce a
1024 byte maximum for the CHAP_C key value following the requirement
in RFC-3720 Section 11.1.4:
"..., C and R are large-binary-values and their binary length (not
the length of the character string that represents them in encoded
form) MUST not exceed 1024 bytes."
Reported-by: rahul.rane <rahul.rane@calsoftinc.com>
Tested-by: rahul.rane <rahul.rane@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Fri, 13 Jun 2014 04:05:16 +0000 (04:05 +0000)]
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
This patch converts chap_server_compute_md5() from simple_strtoul() to
kstrtoul usage().
This addresses the case where a empty 'CHAP_I=' key value received during
mutual authentication would be converted to a '0' by simple_strtoul(),
instead of failing the login attempt.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Tested-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Suman Anna [Tue, 24 Jun 2014 05:24:25 +0000 (00:24 -0500)]
staging: tidspbridge: fix an erroneous removal of parentheses
Commit
4a9fdbb (staging: core: tiomap3430.c Fix line over 80 characters.)
erroneously removed the parentheses around the function pointer leading
to the following build error (when enabling the build of TI DSP/Bridge
driver):
drivers/staging/tidspbridge/core/tiomap3430.c: In function 'bridge_brd_monitor':
drivers/staging/tidspbridge/core/tiomap3430.c:283:10: error: invalid type argument of unary '*' (have 'u32')
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430.o] Error 1
Fix this build error properly.
Fixes:
4a9fdbb (staging: core: tiomap3430.c Fix line over 80 characters.)
Cc: Aybuke Ozdemir <aybuke.147@gmail.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Omar Ramirez Luna <omar.ramirez@copitl.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 26 Jun 2014 20:06:13 +0000 (13:06 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A small collection of fixes/changes for the current series. This
contains:
- Removal of dead code from Gu Zheng.
- Revert of two bad fixes that went in earlier in this round, marking
things as __init that were not purely used from init.
- A fix for blk_mq_start_hw_queue() using the __blk_mq_run_hw_queue(),
which could place us wrongly. Make it use the non __ variant,
which handles cases where we are called from the wrong CPU set.
From me.
- A fix for drbd, which allocates discard requests without room for
the SCSI payload. From Lars Ellenberg.
- A fix for user-after-free in the blkcg code from Tejun.
- Addition of limiting gaps in SG lists, if the hardware needs it.
This is the last pre-req patch for blk-mq to enable the full NVMe
conversion. Could wait until 3.17, but it's simple enough so would
be nice to have everything we need for the NVMe port in the 3.17
release. From me"
* 'for-linus' of git://git.kernel.dk/linux-block:
drbd: fix NULL pointer deref in blk_add_request_payload
blk-mq: blk_mq_start_hw_queue() should use blk_mq_run_hw_queue()
block: add support for limiting gaps in SG lists
bio: remove unused macro bip_vec_idx()
Revert "block: add __init to elv_register"
Revert "block: add __init to blkcg_policy_register"
blkcg: fix use-after-free in __blkg_release_rcu() by making blkcg_gq refcnt an atomic_t
floppy: format block0 read error message properly
Al Viro [Mon, 23 Jun 2014 07:44:40 +0000 (08:44 +0100)]
Fix 32-bit regression in block device read(2)
blkdev_read_iter() wants to cap the iov_iter by the amount of data
remaining to the end of device. That's what iov_iter_truncate() is for
(trim iter->count if it's above the given limit). So far, so good, but
the argument of iov_iter_truncate() is size_t, so on 32bit boxen (in
case of a large device) we end up with that upper limit truncated down
to 32 bits *before* comparing it with iter->count.
Easily fixed by making iov_iter_truncate() take 64bit argument - it does
the right thing after such change (we only reach the assignment in there
when the current value of iter->count is greater than the limit, i.e.
for anything that would get truncated we don't reach the assignment at
all) and that argument is not the new value of iter->count - it's an
upper limit for such.
The overhead of passing u64 is not an issue - the thing is inlined, so
callers passing size_t won't pay any penalty.
Reported-and-tested-by: Theodore Tso <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Thu, 26 Jun 2014 16:30:54 +0000 (12:30 -0400)]
ext4: Fix hole punching for files with indirect blocks
Hole punching code for files with indirect blocks wrongly computed
number of blocks which need to be cleared when traversing the indirect
block tree. That could result in punching more blocks than actually
requested and thus effectively cause a data loss. For example:
fallocate -n -p
10240000 4096
will punch the range
10240000 -
12632064 instead of the range
1024000 -
10244096. Fix the calculation.
CC: stable@vger.kernel.org
Fixes:
8bad6fc813a3a5300f51369c39d315679fd88c72
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jan Kara [Thu, 26 Jun 2014 16:28:57 +0000 (12:28 -0400)]
ext4: Fix block zeroing when punching holes in indirect block files
free_holes_block() passed local variable as a block pointer
to ext4_clear_blocks(). Thus ext4_clear_blocks() zeroed out this local
variable instead of proper place in inode / indirect block. We later
zero out proper place in inode / indirect block but don't dirty the
inode / buffer again which can lead to subtle issues (some changes e.g.
to inode can be lost).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Laura Abbott [Fri, 20 Jun 2014 03:13:38 +0000 (20:13 -0700)]
of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch
The common early_init_dt_add_memory_arch takes the base and size
of a memory region as u64 types. The function never checks if
the base and size can actually fit in a phys_addr_t which may
be smaller than 64-bits. This may result in incorrect memory
being passed to memblock_add if the memory falls outside the
range of phys_addr_t. Add range checks for the base and size if
phys_addr_t is smaller than u64.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Namjae Jeon [Thu, 26 Jun 2014 14:11:53 +0000 (10:11 -0400)]
ext4: decrement free clusters/inodes counters when block group declared bad
We should decrement free clusters counter when block bitmap is marked
as corrupt and free inodes counter when the allocation bitmap is
marked as corrupt to avoid misunderstanding due to incorrect available
size in statfs result. User can get immediately ENOSPC error from
write begin without reaching for the writepages.
Cc: Darrick J. Wong<darrick.wong@oracle.com>
Reported-by: Amit Sahrawat <amit.sahrawat83@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Mengdong Lin [Thu, 26 Jun 2014 10:45:16 +0000 (18:45 +0800)]
ALSA: hda - restore BCLK M/N values when resuming HSW/BDW display controller
For Intel Haswell/Broadwell display HD-A controller, the 24MHz HD-A link BCLK
is converted from Core Display Clock (CDCLK): BCLK = CDCLK * M / N
And there are two registers EM4 and EM5 to program M, N value respectively.
The EM4/EM5 values will be lost and when the display power well is disabled.
BIOS programs CDCLK selected by OEM and EM4/EM5, but BIOS has no idea about
display power well on/off at runtime. So the M/N can be wrong if non-default
CDCLK is used when the audio controller resumes, which results in an invalid
BCLK and abnormal audio playback rate. So this patch saves and restores valid
M/N values on controller suspend/resume.
And 'struct hda_intel' is defined to contain standard HD-A 'struct azx' and
Intel specific fields, as Takashi suggested.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ralf Baechle [Thu, 26 Jun 2014 13:43:01 +0000 (14:43 +0100)]
MIPS: Lasat: Fix build error if CRC32 is not enabled.
Kconfig doesn't select CRC32 so it's possible to build a Lasat kernel
without CONFIG_CRC32 resulting in a build error:
LD vmlinux
arch/mips/built-in.o: In function `lasat_init_board_info':
(.text+0x22c): undefined reference to `crc32_le'
arch/mips/built-in.o: In function `lasat_write_eeprom_info':
(.text+0x7fc): undefined reference to `crc32_le'
make: *** [vmlinux] Error 1
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Grygorii Strashko [Mon, 2 Jun 2014 16:27:58 +0000 (19:27 +0300)]
mfd: ab8500: Fix dt irq mapping
The AD8500 defines itself as interrupt-controller in DT,
but it doesn't assign DT node to IRQ domain when creates it.
As result, of_irq_xx() helpers don't work because they can't
find necessary IRQ domain.
Hence, fix it by assigning AD8500 core device DT node to IRQ
domain when it's created.
This patch fixes STE u8500 Snowball boot failure reported by Kevin Hilman
https://lkml.org/lkml/2014/5/27/624
Reported-and-tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Arnd Bergmann [Thu, 5 Jun 2014 21:24:13 +0000 (23:24 +0200)]
mfd: davinci: Voicecodec needs regmap_mmio
Without REGMAP_MMIO, building that driver results in a link error:
drivers/built-in.o: In function `davinci_vc_probe':
:(.init.text+0x3c1c): undefined reference to `devm_regmap_init_mmio_clk'
This adds a Kconfig 'select' statement as the usual way to ensure
that REGMAP_MMIO is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Arnd Bergmann [Thu, 5 Jun 2014 21:24:14 +0000 (23:24 +0200)]
mfd: STw481x: Allow modular build
This driver depends on I2C, which may be a loadable module.
While you'd probably want both to be built-in in practice,
allowing a modular build avoids possible randconfig link
errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Arnd Bergmann [Thu, 5 Jun 2014 21:24:12 +0000 (23:24 +0200)]
mfd: UCB1x00: Enable modular build
The UCB1200 / UCB1300 driver uses the MCP_SA11X0 driver, which
can be a loadable module, but this results in a link error
when UCB1200 itself is built-in:
drivers/built-in.o: In function `ucb1x00_io_set_dir':
:(.text+0x4a364): undefined reference to `mcp_reg_write'
drivers/built-in.o: In function `ucb1x00_io_write':
:(.text+0x4a3dc): undefined reference to `mcp_reg_write'
drivers/built-in.o: In function `ucb1x00_io_read':
:(.text+0x4a400): undefined reference to `mcp_reg_read'
drivers/built-in.o: In function `ucb1x00_adc_enable':
:(.text+0x4a460): undefined reference to `mcp_enable'
...
This can easily be resolved by making CONFIG_MCP_UCB1200 itself
a tristate option, since that causes Kconfig to track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Sachin Kamat [Fri, 30 May 2014 10:26:34 +0000 (15:56 +0530)]
video: omapdss: Fix potential null pointer dereference
kmalloc can return null. Add a check to avoid potential null
pointer dereference error when the pointer is accessed later.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Emil Goode [Fri, 20 Jun 2014 21:50:37 +0000 (23:50 +0200)]
video: vt8500lcdfb: Remove kfree call since devm_kzalloc() is used
We use devm_kzalloc() to allocate memory for the struct vt8500lcd_info
pointer fbi, so there is no need to free it in vt8500lcd_remove().
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Russell King [Fri, 7 Feb 2014 19:52:33 +0000 (19:52 +0000)]
drm/i2c: tda998x: add some basic mode validation
The TDA998x can't handle modes with clocks above 150MHz, or resolutions
larger than 8192x2048.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 3 Mar 2014 14:09:36 +0000 (14:09 +0000)]
drm/i2c: tda998x: faster polling for edid
One of Jean-Francois patches changed the EDID polling to once every
10ms for 10 interations, whereas the original code did 1ms for 100
interations. This appears to cause boot-time detection to take
noticably longer. Revert this change.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Guido Martínez [Tue, 17 Jun 2014 14:17:03 +0000 (11:17 -0300)]
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
Currently tda998x_encoder_destroy() calls cec_write() and reg_clear(),
as part of the release procedure. Such calls need to access the I2C bus
and therefore, we need to call them before drm_i2c_encoder_destroy()
which unregisters the I2C device.
This commit moves the latter so it's done afterwards.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Ezequiel García <ezequiel@vanguardiasur.com.ar>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Levente Kurusa [Wed, 2 Apr 2014 10:00:37 +0000 (12:00 +0200)]
TC: Handle device_register() errors.
Make the TURBOchannel driver bail out if the call to device_register()
failed.
Signed-off-by: Levente Kurusa <levex@linux.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6673/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 08:48:51 +0000 (09:48 +0100)]
MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region
Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:
CPU 0 Unable to handle kernel paging request at virtual address
e75c0200,
epc ==
8058dba4, ra ==
8058db90
[...]
Call Trace:
[<
8058dba4>] init_msc_irqs+0x104/0x154
[<
8058b5bc>] arch_init_irq+0xd8/0x154
[<
805897b0>] start_kernel+0x220/0x36c
Kernel panic - not syncing: Attempted to kill the idle task!
This patch fixes the problem
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7118/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:39:00 +0000 (10:39 +0100)]
MIPS: bpf: Fix stack space allocation for BPF memwords on MIPS64
When allocating stack space for BPF memwords we need to use the
appropriate 32 or 64-bit instruction to avoid losing the top 32 bits
of the stack pointer.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Wed, 25 Jun 2014 08:39:38 +0000 (09:39 +0100)]
MIPS: BPF: Use 32 or 64-bit load instruction to load an address to register
When loading a pointer to register we need to use the appropriate
32 or 64bit instruction to preserve the pointers' top 32bits.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7180/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:58 +0000 (10:38 +0100)]
MIPS: bpf: Fix PKT_TYPE case for big-endian cores
The skb->pkt_type field is defined as follows:
u8 pkt_type:3,
fclone:2,
ipvs_property:1,
peeked:1,
nf_trace:1
resulting to the following layout in big-endian systems
[pkt_type][fclone][ipvs_propery][peeked][nf_trace]
^ ^
| |
LSB MSB
As a result, the existing code did not work because it was trying to
match pkt_type == 7 whereas in reality it is 7<<5 on big-endian
systems.
This has been fixed in the interpreter in
0dcceabb0c1bf2d4c12a748df9933fad303072a7
"net: filter: fix SKF_AD_PKTTYPE extension on big-endian"
The fix is to look for 7<<5 on big-endian systems for the pkt_type
field, and shift by 5 so the packet type will be at the lower 3 bits
of the A register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Wed, 25 Jun 2014 08:37:21 +0000 (09:37 +0100)]
MIPS: BPF: Prevent kernel fall over for >=32bit shifts
Remove BUG_ON() if the shift immediate is >=32 to avoid kernel crashes
due to malicious user input. If the shift immediate is >= 32,
we simply load the destination register with 0 since only
32-bit instructions are used by JIT so this will do the
correct thing even on MIPS64.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:56 +0000 (10:38 +0100)]
MIPS: bpf: Drop update_on_xread and always initialize the X register
Previously, update_on_xread() only set the reset flag if SEEN_X hasn't
been set already. However, SEEN_X is used to indicate that X is used
as destination or source register so there are some cases where X
is only used as source register and we really need to make sure that it
has been initialized in time. As a result of which, drop this function and
always set X to zero if it's used in any of the opcodes.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:55 +0000 (10:38 +0100)]
MIPS: bpf: Fix is_range() semantics
is_range() was meant to check whether the number is within
the s16 range or not. However the return values and consumers expected
the exact opposite. We fix that by inverting the logic in the function
to return 'true' for < s16 and 'false' for > s16.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7131/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:54 +0000 (10:38 +0100)]
MIPS: bpf: Use pr_debug instead of pr_warn for unhandled opcodes
We should prevent spamming the logs during normal execution of bpf-jit.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Suggested-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7129/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:53 +0000 (10:38 +0100)]
MIPS: bpf: Fix return values for VLAN_TAG_PRESENT case
If VLAN_TAG_PRESENT is not zero, then return 1 as expected by
classic BPF. Otherwise return 0.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7128/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:52 +0000 (10:38 +0100)]
MIPS: bpf: Use correct mask for VLAN_TAG case
Using VLAN_VID_MASK is not correct to get the vlan tag. Use
~VLAN_PRESENT_MASK instead and make sure it's u16 so the top 16-bits
will be removed. This will ensure that the emit_andi() code will not
treat this as a big 32-bit unsigned value.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7127/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:51 +0000 (10:38 +0100)]
MIPS: bpf: Fix branch conditional for BPF_J{GT/GE} cases
The sltiu and sltu instructions will set the scratch register
to 1 if A <= X|K so fix the emitted branch conditional to check
for scratch != zero rather than scratch >= zero which would complicate
the resuling branch logic given that MIPS does not have a BGT or BGET
instructions to compare general purpose registers directly.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7126/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>