OSDN Git Service
Jani Nikula [Fri, 14 Nov 2014 14:54:21 +0000 (16:54 +0200)]
drm/i915/dsi: clean up MIPI DSI pipe vs. port usage
MIPI DSI works on ports A and C, which map to pipes A and B,
respectively. Things are going to get more complicated with the
introduction of dual link DSI support, so clean up the register defines
and code to match reality.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 26 Nov 2014 15:07:29 +0000 (17:07 +0200)]
drm/i915: Deal with video overlay on GPU reset
Clear the video overlay state on GPU reset. Any pending overlay request
in the ring has been nuked, and the display itself gets reset. So we
pretty much lose all state here. Adjust the software state to match so
that the next "putimage" will restore things to working order.
v2: Ass a locking check into intel_overlay_release_old_vid() (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/0/NULL/ to appease sparse, reported by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:39 +0000 (18:49 +0000)]
drm/i915: Convert 'trace_irq' to use requests rather than seqnos
Updated the trace_irq code to use requests instead of seqnos. This includes
reference counting the request object to ensure it sticks around when required.
Note that getting access to the reference counting functions means moving the
inline i915_trace_irq_get() function from intel_ringbuffer.h to i915_drv.h.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Resolve conflict due to shuffled merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 26 Nov 2014 13:39:48 +0000 (14:39 +0100)]
drm/i915: Remove redundant flip_work->flip_queued_ring
Similar to the patch from John which removed obj->ring.
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
John Harrison [Mon, 24 Nov 2014 18:49:43 +0000 (18:49 +0000)]
drm/i915: Remove the now redundant 'obj->ring'
The ring member of the object structure was always updated with the
last_read_seqno member. Thus with the conversion to last_read_req, obj->ring is
now a direct copy of obj->last_read_req->ring. This makes it somewhat redundant
and potentially misleading (especially as there was no comment to explain its
purpose).
This checkin removes the redundant field. Many uses were simply testing for
non-null to see if the object is active on the GPU. Some of these have been
converted to check 'obj->active' instead. Others (where the last_read_req is
about to be used anyway) have been changed to check obj->last_read_req. The rest
simply pull the ring out from the request structure and proceed as before.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:42 +0000 (18:49 +0000)]
drm/i915: Convert 'i915_seqno_passed' calls into 'i915_gem_request_completed'
Almost everywhere that caled i915_seqno_passed() was really asking 'has the
given seqno popped out of the hardware yet?'. Thus it had to query the current
hardware seqno and then do a signed delta comparison (which copes with wrapping
around zero but not with seqno values more than 2GB apart, although the latter
is unlikely!).
Now that the majority of seqno instances have been replaced with request
structures, it is possible to convert this test to be request based as well.
There is now a 'i915_gem_request_completed()' function which takes a request and
returns true or false as appropriate. Note that this currently just wraps up the
original _passed() test but a later patch in the series will reduce this to
simply returning a cached internal value, i.e.:
_completed(req) { return req->completed; }'
This checkin converts almost all _seqno_passed() calls. The only one left is in
the semaphore code which still requires seqnos not request structures.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Drop hunk touching the trace_irq code since I've dropped the
patch which converts that, and resolve resulting conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:41 +0000 (18:49 +0000)]
drm/i915: Connect requests to rings at creation not submission
It makes a lot more sense (and makes future seqno -> request conversion patches
simpler) to fill in the 'ring' field of the request structure at the point of
creation rather than submission. Given that the request structure is assigned by
ring specific code and thus is locked to a ring from the start, there really is
no reason to defer this assignment.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:40 +0000 (18:49 +0000)]
drm/i915: Convert 'ring_idle()' to use requests not seqnos
More seqno value to request structure conversions. Note, this change temporarily
moves the 'get_seqno()' call inside ring_idle() but this will disappear again in
a later patch when i915_seqno_passed() itself is converted.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:38 +0000 (18:49 +0000)]
drm/i915: Convert trace functions from seqno to request
All the code above is now using requests not seqnos so it is possible to convert
the trace functions across. Note that rather than get into problematic reference
counting issues, the trace code only saves the seqno and ring values from the
request structure not the structure pointer itself.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:37 +0000 (18:49 +0000)]
drm/i915: Convert 'flip_queued_seqno' into 'flip_queued_request'
Converted the flip_queued_seqno value to be a request structure as part of the
on going seqno to request changes. This includes reference counting the request
being saved away to ensure it can not be retired and freed while the flip code
is still waiting on it.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Again get rid of the _irq request unref by simply moving that
into the unpin worker. Doesn't matter when we hang onto the request
for a bit longer, and in the unpin worker we already grab the
dev->struct_mutex anyway.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:36 +0000 (18:49 +0000)]
drm/i915: Remove obsolete seqno parameter from 'i915_add_request'
There is no longer any need to retrieve a seqno value from an i915_add_request()
call. The calling code already knows which request structure is being processed
(it can only be ring->OLR). And as the request itself is now used in preference
to the basic seqno value, the latter is now redundant in this situation.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:35 +0000 (18:49 +0000)]
drm/i915: Convert __wait_seqno() to __wait_request()
Now that all code above is using request structures instead of seqno values, it
is possible to convert __wait_seqno() itself. Internally, it is still calling
i915_seqno_passed(), this will be updated later in the series. This step is just
changing the parameter list and function name.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:34 +0000 (18:49 +0000)]
drm/i915: Convert mmio_flip::seqno to struct request
Converted the mmio_flip 'seqno' value to be a request structure as part of the
on going seqno to request changes. This includes reference counting the request
being saved away to ensure it can not be retired and freed while the flip code
is still waiting on it.
v2: Used the IRQ friendly request dereference call in the notify handler as that
code is called asynchronously without holding any useful mutex locks.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Drop the _irq variant and use the normal reques unref,
wrapped in dev->struct_mutex per the discussion on the m-l.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 26 Nov 2014 09:26:05 +0000 (10:26 +0100)]
drm/i915: Check locking in i915_gem_request_unreference
With refcounting it looks like you can just drop that refcount, but
that's not really the case. So make sure no one forgets.
Motivated by the unlocked call in the mmio flip code.
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Daniel Vetter [Wed, 26 Nov 2014 13:17:05 +0000 (14:17 +0100)]
drm/i915: Convert i915_wait_seqno to i915_wait_request
Updated i915_wait_seqno() to take a request structure instead of a seqno value
and renamed it accordingly. Internally, it just pulls the seqno out of the
request and calls on to __wait_seqno() as before. However, all the code further
up the stack is now simplified as it can just pass the request object straight
through without having to peek inside.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Squash in hunk from an earlier patch which was rebased
wrongly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:31 +0000 (18:49 +0000)]
drm/i915: Convert 'last_flip_req' to be a request not a seqno
Converted 'last_flip_req' to be an actual request rather than a seqno value as
part of the on going seqno to request changes. This includes reference counting
the request being saved away to ensure it can not be retired and freed while the
overlay code is still waiting on it.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:30 +0000 (18:49 +0000)]
drm/i915: Make 'i915_gem_check_olr' actually check by request not seqno
Updated the _check_olr() function to actually take a request object and compare
it to the OLR rather than extracting seqnos and comparing those.
Note that there is one use case where the request object being processed is no
longer available at that point in the call stack. Hence a temporary copy of the
original function is still present (but called _check_ols() instead). This will
be removed in a subsequent patch.
Also, downgraded a BUG_ON to a WARN_ON as apparently the former is frowned upon
for shipping code.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:29 +0000 (18:49 +0000)]
drm/i915: Remove 'outstanding_lazy_seqno'
The OLS value is now obsolete. Exactly the same value is guarateed to be always
available as PLR->seqno. Thus it is safe to remove the OLS completely. And also
to rename the PLR to OLR to keep the 'outstanding lazy ...' naming convention
valid.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:28 +0000 (18:49 +0000)]
drm/i915: Ensure requests stick around during waits
Added reference counting of the request structure around __wait_seqno() calls.
This is a precursor to updating the wait code itself to take the request rather
than a seqno. At that point, it would be a Bad Idea for a request object to be
retired and freed while the wait code is still using it.
v3:
Note that even though the mutex lock is held during a call to i915_wait_seqno(),
it is still necessary to explicitly bump the reference count. It appears that
the shrinker can asynchronously retire items even though the mutex is locked.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Remove wrongly squashed hunk which breaks the build.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:27 +0000 (18:49 +0000)]
drm/i915: Convert i915_gem_ring_throttle to use requests
Convert the throttle code to use the request structure rather than extracting a
ring/seqno pair from it and using those. This is in preparation for
__wait_seqno() becoming __wait_request().
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:26 +0000 (18:49 +0000)]
drm/i915: Replace last_[rwf]_seqno with last_[rwf]_req
The object structure contains the last read, write and fenced seqno values for
use in syncrhonisation operations. These have now been replaced with their
request structure counterparts.
Note that to ensure that objects do not end up with dangling pointers, the
assignments of last_*_req include reference count updates. Thus a request cannot
be freed if an object is still hanging on to it for any reason.
v2: Corrected 'last_rendering_' to 'last_read_' in a number of comments that did
not get updated when 'last_rendering_seqno' became 'last_read|write_seqno'
several millenia ago.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:25 +0000 (18:49 +0000)]
drm/i915: Add helper functions to aid seqno -> request transition
Added helper functions for retrieving the ring and seqno entries from a request
structure. This allows the internal workings of the request structure to be
hidden from code that is using these. It also allows for useful
workarounds/debug code to be added as or when necessary.
Note that it is intended that the majority (if not all) uses of the seqno
accessor will disappear eventually as code is updated to use the request
structure itself rather than working with seqno values.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:24 +0000 (18:49 +0000)]
drm/i915: Add reference count to request structure
The plan is to use request structures everywhere that seqno values were
previously used. This means saving pointers to structures in places that used to
be simple integers. In turn, that means that the target structure now needs much
more stringent lifetime tracking. That is, it must not be freed while some other
random object still holds a pointer to it.
To achieve this tracking, a reference count needs to be added. Whenever a
pointer to the structure is saved away, the count must be incremented and the
free must only occur when all references have been released.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Mon, 24 Nov 2014 18:49:23 +0000 (18:49 +0000)]
drm/i915: Ensure OLS & PLR are always in sync
The aim is to replace seqno values with request structures. A step along the way
is to switch to using the PLR in preference to the OLS. That requires the PLR to
only be valid when and only when the OLS is also valid. I.e., the two must be
kept in lock step. Then, code which was using the OLS can be safely switched
over to using the PLR instead.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 25 Nov 2014 13:45:41 +0000 (13:45 +0000)]
drm/i915: Fix short description of intel_display_power_is_enabled()
That's the version actually taking the dev_priv->power_domains lock.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 25 Nov 2014 11:56:33 +0000 (11:56 +0000)]
drm/i915: Assert that we successfully downclock the GPU before suspend
Before suspending, we wait upon the outstanding GPU requests and flush
our pending idle handlers. This should downclock the GPU to its lowest
power state. Add a WARN to check that the delayed tasks were run and did
their job properly.
Suggested-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 24 Nov 2014 10:21:52 +0000 (11:21 +0100)]
drm/i915: Remove user pinning code
Now unused.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Dave Gordon [Tue, 18 Nov 2014 20:07:21 +0000 (20:07 +0000)]
drm/i915: Don't read 'HEAD' MMIO register in LRC mode
The logical ring code was updating the software ring 'head' value
by reading the hardware 'HEAD' register. In LRC mode, this is not
valid as the hardware is not necessarily executing the same context
that is being processed by the software. Thus reading the h/w HEAD
could put an unrelated (undefined, effectively random) value into
the s/w 'head' -- A Bad Thing for the free space calculations.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Gordon [Tue, 18 Nov 2014 20:07:20 +0000 (20:07 +0000)]
drm/i915: Check for matching ringbuffer in logical_ring_wait_request()
The request queue is per-engine, and may therefore contain requests
from several different contexts/ringbuffers. In determining which
request to wait for, this function should only consider requests
from the ringbuffer that it's checking for space, and ignore any
that it finds that belong to other contexts.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 20 Nov 2014 11:44:37 +0000 (03:44 -0800)]
drm/i915: Enable PSR for Baytrail and Braswell.
This patch is the last in series of VLV/CHV PSR,
that finally enable PSR by adding it to HAS_PSR
and calling the proper enable and disable
functions on the right places.
Although it is still disabled by default.
v2: Rebase over intel_psr and merge Durgadoss's fixes.
v3: Fix typo.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 14 Nov 2014 16:52:40 +0000 (08:52 -0800)]
drm/i915: VLV/CHV PSR debugfs.
Add debugfs support for Valleyview and Cherryview considering that
we have PSR per pipe and we don't have any kind of
performance counter as we have on other platforms that support PSR.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Wed, 19 Nov 2014 15:37:47 +0000 (07:37 -0800)]
drm/i915: VLV/CHV PSR Software timer mode
This patch introduces exit/activate functions for PSR
on VLV+. Since on VLV+ HW cannot track frame updates and force PSR
exit let's use fully SW tracking available.
v2: Rebase over intel_psr.c;
Remove Single Frame update transitioning from state 3 to 5 directly;
Fake a software invalidation for sprites and cursor so we don't miss
any screen update;
v3: As pointed out by Durgadoss msecs_to_jiffies used on wait_for only uses int,
so let's use 1 instead. Althought the 1/4 of this is needed for the
transition let's use 1 for simplicity;
Also fix comments as suggested by Durgadoss
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Wed, 19 Nov 2014 15:37:00 +0000 (07:37 -0800)]
drm/i915: PSR VLV/CHV: Introduce setup, enable and disable functions
The biggest difference from HSW/BDW PSR here is that VLV enable_source
function enables PSR but let it in Inactive state. So it might be called
on early stage along with setup and enable_sink ones.
v2: Rebase over intel_psr.c;
Remove docs from static functions;
Merge vlv_psr_active_on_pipe;
Timeout for psr transition is 250us;
Remove SRC_TRASMITTER_STATE;
v3: Rebase after is_psr_enabled function got removed;
Get SRC_TRANSMITTER_STATE back to be on the safe side since
default for panels is to require link training on exit when
main link off;
As pointed out by Durgadoss msecs_to_jiffies used on wait_for only uses int,
so let's use 1 instead. Althought the 1/4 of this is needed for the
transition let's use 1 for simplicity;
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 14 Nov 2014 16:52:36 +0000 (08:52 -0800)]
drm/i915: Add PSR registers for PSR VLV/CHV.
Baytrail (Valleyview) and Braswell (Cherryview) uses a complete different
implementation of PSR that we currently have supported for
Haswell and Broadwell. So let's start by adding registers definitions.
I usually don't like commit that adds just registers without using,
but after I put all in one commit I realized that no one would want
to take the AR to review it so I decided to split in order to make
reviewer's life easier. Only last commit in this series will actually
enable the PSR on intel enable panel path.
But as it happens currently with HSW/BDW the plan is to let it
disabled by default (protected by kernel parameter)
while we are able to fully validate it.
v2: Remove a unused bit definition that isn't used on vlv and
reserved on chv as pointed out by Durgadoss.
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 20 Nov 2014 10:22:08 +0000 (02:22 -0800)]
drm/i915: Remove intel_psr_is_enabled function.
This function was in use to check if PSR feature got enabled.
However on HSW and BDW we currently force psr exit by disabling
EDP_PSR_ENABLE bit at EDP_PSR_CTL(dev). So this function was actually
returning the active/inactive state that is different from the enable/disable
meaning and had the risk of false negative.
But anyway this check with DRRS was dangerous, since DRRS could try to get enabled
before PSR gets there. So let's just remove it for now.
A proper synchronization mechanism must be implemented later probably
using pipe config.
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Wed, 19 Nov 2014 15:34:04 +0000 (07:34 -0800)]
drm/i915: remove PSR BDW single frame update.
Single frame update is a feature available on BDW for PSR that allows
Source to send Sink only one frame and get it updated. Usually useful
when page flipping. However with our frontbuffer tracking where we force
psr exit on flips we don't need this feature.
Also after it got added here many workaround was added to documentation
to mask some bits when using single frame update. So the safest thing
is to just stop using it.
v2: Rebase after removing skip aux one and fixing typo on commit message.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 14 Nov 2014 16:52:32 +0000 (08:52 -0800)]
drm/i915: PSR get full link off x standby from VBT
OEMs can specify if full_link might be always enabled, i.e. only_standby
over VBT.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 14 Nov 2014 16:52:31 +0000 (08:52 -0800)]
drm/i915: HSW/BDW PSR Set idle_frames = VBT + 1
Let's use VBT + 1 now we parse it.
v2: fix subject
v3: rebase over intel_psr and without counting on previous fix
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 14 Nov 2014 16:52:30 +0000 (08:52 -0800)]
drm/i915: Parse VBT PSR block.
PSR (aka SRD) block is defined at VBT and currently being used.
Mainly/At-least to configure the amount of idle_frames require to get
back to PSR Entry.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Thu, 20 Nov 2014 14:58:16 +0000 (14:58 +0000)]
drm/i915/skl: Implement the skl version of MMIO flips
Because the plane registers are different in Skylake we need to adapt
the MMIO code as well.
v2: Don't introduce yet another vfunc when the direction is do
consolidate the plane updates to use the same code path (Daniel)
v3:
- Use enum pipe instead of int (Ville)
- Also update PLANE_STRIDE when the tiling has changed (Ville)
- Put intel_mark_page_flip_active() in the shared code (Damien)
v4:
- Remove unused variable
v5:
- Fix whitespace Vs tabs (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 21 Nov 2014 16:14:56 +0000 (16:14 +0000)]
drm/i915/skl: Read out crtl1 for eDP/DPLL0
v2: Put the DPLL0 state readout in skylake_get_ddi_pll(), closer to
where the PLL assignement read out is done rather than the frequency
readout function. (Daniel)
v3: Remove stray new line (Damien)
Add Paulo's r-b tag for v1
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 2 Dec 2014 12:10:46 +0000 (14:10 +0200)]
drm/i915: Reject modeset when the same digital port is used more than once
On pre-HSW we have two encoders per digital port: one HDMI, one DP.
However they are the same physical port in hardware and we can't enable
both at the same time. Reject the modeset if the user attempts this.
So far we've been saved by the fact that we never see both HDMI and DP
connectors as connected. But if the user decides to force a mode anyway,
all kinds of funny stuff might happen.
Unfortunately we don't seem to have any way to inform userspace that
such configurations are invalid except by returning an error from
setcrtc. possible_clones only covers real cloning situations, and
looking at the connector names doesn't work either since we don't
always register both connectors for the same port. I suppose the
only way to fix that would be to expose only a single encoder per
digital port like we do on HSW+ but that would be a fairly large
undertaking for little gain.
kms_setmode hits this since it forces modes on non-connected VGA and
HDMI connectors. Previosuly it just resulted in weirdness such as
failed link training. With this patch it will now get an error back
from the kernel and will die with an assert since it thinks that the
configuration should be fine.
v2: Deal with INTEL_OUTPUT_UNKNOWN (Paulo)
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 20 Nov 2014 21:01:47 +0000 (23:01 +0200)]
drm/i915: mask RPS IRQs properly when disabling RPS
Atm, igt/gem_reset_stats can trigger the recently added WARN on
left-over PM_IIR bits in gen6_enable_rps_interrupts(). There are two
reasons for this:
1. we call intel_enable_gt_powersave() without a preceeding
intel_disable_gt_powersave()
2. gen6_disable_rps_interrupts() doesn't mask interrupts in PM_IMR
1. means RPS interrupts will remain enabled and can be serviced during
the HW initialization after a GPU reset. 2. means even if we called
gen6_disable_rps_interrupts() any new RPS interrupt during RPS
initialization would still propagate to PM_IIR too early (though
wouldn't be serviced).
This patch solves the 2. issue by also masking interrupts in PM_IMR, the
following patch fixes 1. getting rid of the WARN. This also makes
intel_enable_gt_powersave() and intel_disable_gt_powersave() more
symmetric.
Since gen6_disable_rps_interrupts() is called during driver loading with
i915 interrupts disabled add a new version of gen6_disable_pm_irq() that
doesn't WARN for this.
Also while at it, get the irq_lock around the whole PM_IMR/IER/IIR
programming sequence and make sure that any queued PM_IIR bit is also
cleared.
The WARN was caught by PRTS after I sent my previous RPS sanitizing
patchset and I could easily reproduce it on HSW. To actually fix it we
also need the next patch.
Reported-by: He, Shuang <shuang.he@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 26 Nov 2014 15:29:04 +0000 (16:29 +0100)]
drm/i915: Tune down spurious CRC interrupt warning
We don't really synchronously turn them off from debugfs. We try to
avoid hitting them too badly by waiting one vblank, but apparently the
irq handler can still race through that gap.
Since this isn't really all that important for testcases, only for
debugging CRC issues let's tune it down to a debug message.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82602
Cc: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Thomas Daniel [Tue, 25 Nov 2014 10:39:25 +0000 (10:39 +0000)]
drm/i915: Fix context object leak for legacy contexts
Dynamic context pinning for LRCs introduced a leak in legacy mode.
Reinstate context unreference in i915_gem_free_request for legacy contexts.
Leak reported by i-g-t/drv_module_reload fixed by this patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86507
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: John Harrison<John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Akash Goel [Tue, 25 Nov 2014 06:59:00 +0000 (12:29 +0530)]
drm/i915/skl: Update in Gen9 multi-engine forcewake range
Updates in forcewake range for Render/Media/Common
power wells for Gen9.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Egbert Eich [Tue, 25 Nov 2014 11:54:57 +0000 (12:54 +0100)]
drm/i915/eDP: When enabling panel VDD cancel pending disable worker
Before testing if the panel VDD is enabled on eDP cancel any pending
disable worker. This makes sure the worker will be triggered with a
delay from the last time edp_panel_vdd_schedule_off() is called, not
the first time. This avoids unnecessary overhead.
https://bugs.freedesktop.org/show_bug.cgi?id=86201
v2: use cancel_delayed_work() instead of cancel_delayed_work_sync()
as the pps_mutexes will provide the required serialization with
edp_panel_vdd_work() while the sync variant may deadlock. Suggested
by Ville Syrjälä <ville.syrjala@linux.intel.com>.
Made commit message a bit clearer.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 25 Nov 2014 13:00:40 +0000 (14:00 +0100)]
drm/i915: Handle runtime pm in the CRC setup code
The crc code doesn't handle anything really that could drop the
register state (by design so that we have less complexity). Which
means userspace may only start crc capture once the pipe is fully set
up.
With an i-g-t patch this will be the case, but there's still the
problem that this results in obscure unclaimed register write
failures. Which is a pain to debug.
So instead make sure we don't have the basic unclaimed register write
failure by grabbing runtime pm references. And reject completely
invalid requests with -EIO. This is still racy of course, but for a
test library we don't really care - if userspace shuts down the pipe
right afterwards the entire setup will be lost anyway.
v2: Put instead of get, spotted by Damien. Also explain the runtime pm
dance.
v3: There's really no need for rpm get/put since power_is_enabled only
checks software state (Damien).
References: https://bugs.freedesktop.org/show_bug.cgi?id=86092
Cc: Damien Lespiau <damien.lespiau@intel.com> (v2)
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Ville Syrjälä [Fri, 21 Nov 2014 19:54:30 +0000 (21:54 +0200)]
drm/i915: Disable crtcs gracefully before GPU reset on gen3/4
The GPU reset also resets the display on gen3/4. The g33 docs say we
should disable all planes before flipping the reset switch. Just
disable all the crtcs instead. That seems a nicer thing to do anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 24 Nov 2014 16:28:11 +0000 (18:28 +0200)]
drm/i915: Grab modeset locks for GPU rest on pre-ctg
On gen4 and earlier the GPU reset also resets the display, so we should
protect against concurrent modeset operations. Grab all the modeset locks
around the entire GPU reset dance, remebering first ti dislogde any
pending page flip to make sure we don't deadlock. Any pageflip coming
in between these two steps should fail anyway due to reset_in_progress,
so this should be safe.
This fixes a lot of failed asserts in the modeset code when there's a
modeset racing with the reset. Naturally the asserts aren't happy when
the expected state has disappeared.
v2: Drop UMS checks, complete pending flips after the reset (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 21 Nov 2014 19:54:28 +0000 (21:54 +0200)]
drm/i915: Implement GPU reset for g33
g33 seems to sit somewhere between the 915/945/965 style and the
g4x style. The bits look like g4x, but we still need to do a full
reset including display.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 21 Nov 2014 19:54:27 +0000 (21:54 +0200)]
drm/i915: Implement GPU reset for 915/945
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 21 Nov 2014 19:54:26 +0000 (21:54 +0200)]
drm/i915: Restore the display config after a GPU reset on gen4
On pre-ctg GPU reset also resets the display hardware. Force a mode
restore after the GPU reset, and also re-init clock gating.
v2: Use intel_modeset_init_hw() instead of intel_init_clock_gating()
in case more relevant stuff gets added there at some point
Restore interrupts after the reset as well
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 21 Nov 2014 19:54:25 +0000 (21:54 +0200)]
drm/i915: Fix gen4 GPU reset
On pre-ctg the reset bit directly controls the reset signal. We must
assert it for >=20usec and then deassert it. Bit 1 is a RO status bit
which should also go down when the reset is no longer asserted.
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 4 Nov 2014 14:52:22 +0000 (15:52 +0100)]
drm/i915: Stop gathering error states for CS error interrupts
There's quite a few bug reports with error states where the error
reasons makes just about no sense at all. Like dying on tlbs for a
display plane that's not even there. Also users don't really report a
lot of bad side effects generally, just the error states.
Furthermore we don't even enable these interrupts any more on gen5+
(though the handling code is still there). So this mostly concerns old
platforms.
Given all that lets make our lives a bit easier and stop capturing
error states, in the hopes that we can just ignore them. In case
that's not true and the gpu indeed dies the hangcheck should
eventually kick in. And I've left some debug log in to make this case
noticeble. Referenced bug is just an example.
v2: Fix missing \n Jani spotted.
References: https://bugs.freedesktop.org/show_bug.cgi?id=82095
References: https://bugs.freedesktop.org/show_bug.cgi?id=85944
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 24 Nov 2014 10:12:42 +0000 (11:12 +0100)]
drm/i915: Disallow pin ioctl completely for kms drivers
The problem here is that SNA pins batchbuffers to etch out a bit more
performance. Iirc it started out as a w/a for i830M (which we've
implemented in the kernel since a long time already). The problem is
that the pin ioctl wasn't added in
commit
d23db88c3ab233daed18709e3a24d6c95344117f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri May 23 08:48:08 2014 +0200
drm/i915: Prevent negative relocation deltas from wrapping
Fix this by simply disallowing pinning from userspace so that the
kernel is in full control of batch placement again. Especially since
distros are moving towards running X as non-root, so most users won't
even be able to see any benefits.
UMS support is dead now, but we need this minimal patch for
backporting. Follow-up patch will remove the pin ioctl code
completely.
Note to backporters: You must have both
commit
b45305fce5bb1abec263fcff9d81ebecd6306ede
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Dec 17 16:21:27 2012 +0100
drm/i915: Implement workaround for broken CS tlb on i830/845
which laned in 3.8 and
commit
c4d69da167fa967749aeb70bc0e94a457e5d00c1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Sep 8 14:25:41 2014 +0100
drm/i915: Evict CS TLBs between batches
which is also marked cc: stable. Otherwise this could introduce a
regression by disabling the userspace w/a without the kernel w/a being
fully functional on i830/45.
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554#c116
Cc: stable@vger.kernel.org # requires c4d69da167fa967749a and v3.8
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Chris Wilson [Mon, 24 Nov 2014 08:03:12 +0000 (08:03 +0000)]
drm/i915: Only warn the first time we attempt to mmio whilst suspended
In all likelihood we will do a few hundred errnoneous register
operations if we do a single invalid register access whilst the device
is suspended. As each instance causes a WARN, this floods the system
logs and can make the system unresponsive.
The warning was first introduced in
commit
b2ec142cb0101f298f8e091c7d75b1ec5b809b65
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Feb 21 13:52:25 2014 -0300
drm/i915: call assert_device_not_suspended at gen6_force_wake_work
and despite the claims the WARN is still encountered in the wild today.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clint Taylor [Fri, 21 Nov 2014 19:13:02 +0000 (11:13 -0800)]
drm/i915/chv: Enable AVI, SPD and HDMI infoframes for CHV.
CHV infoframes were not being enabled.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 21 Nov 2014 19:00:36 +0000 (21:00 +0200)]
drm/i915: Don't clobber crtc->new_config when nothing changes
When doing a nop modeset we currently leave crtc->new_config point at
the already freed temporary pipe_config. That will anger the sanity
checks in intel_modeset_update_state() when the nop modeset gets
followed by a GPU reset on gen3/4 where the display block gets fully
reinitialized during the reset.
So leave crtc->new_config alone until we know a modeset is actually
required.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Laurent Pinchart [Thu, 27 Nov 2014 12:49:07 +0000 (14:49 +0200)]
drm: rcar-du: Fix NULL encoder pointer dereference
The DRM connector's encoder pointer is managed internally by the DRM
core and set to NULL when the DRM connector is disconnected from the
CRTC it was attached to. This results in a NULL pointer dereference in
the HDMI connector functions when trying to call the associated slave
encoder's operations.
Fix this by retrieving the slave encoder pointer from the R-Car
connector structure instead of the DRM connector structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 2 Dec 2014 22:25:59 +0000 (08:25 +1000)]
Merge tag 'drm-intel-next-2014-11-21-fixed' of git://anongit.freedesktop.org/drm-intel into drm-next
drm-intel-next-2014-11-21:
- infoframe tracking (for fastboot) from Jesse
- start of the dri1/ums support removal
- vlv forcewake timeout fixes (Imre)
- bunch of patches to polish the rps code (Imre) and improve it on bdw (Tom
O'Rourke)
- on-demand pinning for execlist contexts
- vlv/chv backlight improvements (Ville)
- gen8+ render ctx w/a work from various people
- skl edp programming (Satheeshakrishna et al.)
- psr docbook (Rodrigo)
- piles of little fixes and improvements all over, as usual
* tag 'drm-intel-next-2014-11-21-fixed' of git://anongit.freedesktop.org/drm-intel: (117 commits)
drm/i915: Don't pin LRC in GGTT when dumping in debugfs
drm/i915: Update DRIVER_DATE to
20141121
drm/i915/g4x: fix g4x infoframe readout
drm/i915: Only call mod_timer() if not already pending
drm/i915: Don't rely upon encoder->type for infoframe hw state readout
drm/i915: remove the IRQs enabled WARN from intel_disable_gt_powersave
drm/i915: Use ggtt error obj capture helper for gen8 semaphores
drm/i915: vlv: increase timeout when setting idle GPU freq
drm/i915: vlv: fix cdclk setting during modeset while suspended
drm/i915: Dump hdmi pipe_config state
drm/i915: Gen9 shadowed registers
drm/i915/skl: Gen9 multi-engine forcewake
drm/i915: Read power well status before other registers for drpc info
drm/i915: Pin tiled objects for L-shaped configs
drm/i915: Update ring freq for full gpu freq range
drm/i915: change initial rps frequency for gen8
drm/i915: Keep min freq above floor on HSW/BDW
drm/i915: Use efficient frequency for HSW/BDW
drm/i915: Can i915_gem_init_ioctl
drm/i915: Sanitize ->lastclose
...
Thomas Daniel [Tue, 2 Dec 2014 13:21:18 +0000 (13:21 +0000)]
drm/i915: Don't pin LRC in GGTT when dumping in debugfs
LRC object does not need to be mapped into the GGTT when dumping. A side-effect
of this patch is that a compiler warning goes away (not checking return value
of i915_gem_obj_ggtt_pin).
v2: Broke out individual context dumping into a new function as the indentation
was getting a bit crazy. Added notification of contexts with no gem object for
debugging purposes. Removed unnecessary pin_pages and unpin_pages, replaced
with explicit get_pages for the context object as there may be no backing store
allocated at this time (Comment for get_pages says "Ensure that the associated
pages are gathered from the backing storage and pinned into our object").
Improved error checking - get_pages and get_page are checked for failure.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Align paramter continuation lines properly. Also add some
braces to the nested loops again for readability.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Tue, 2 Dec 2014 06:13:12 +0000 (16:13 +1000)]
Merge branch 'linux-3.19' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
- Tegra K1 voltage support, and coherency improvements
- GM204 support (modesetting, still waiting on NVIDIA for signed fw to
proceed further), and a lot of bios/i2c/devinit adjustments needed to
support it
- GT21x memory reclocking work
- Various other bits and pieces, most of which are prep-work for a
couple of bigger projects I didn't get finished in time
* 'linux-3.19' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (73 commits)
drm/nv50/kms: drop requirement that framebuffer bos be contig up-front
drm/nv50/kms: directly use cursor image from userspace buffer
drm/nouveau/kms: when pinning display-related buffers, force contig vram
drm/nouveau: teach nouveau_bo_pin() how to force a contig vram allocation
drm/nouveau/volt: add support for GK20A
drm/nouveau/platform: add GPU speedo information to nouveau platform
drm/nouveau/volt: allow non-bios voltage scaling
drm/gf100-/gr: return non-fatal error code when fw not present
drm/nouveau/devinit: bump priv ring timeouts before executing scripts
drm/nouveau/bios: translate ramcfg strap through M0203
drm/nouveau/fb: make use of M0203 routines for ram type determination
drm/nouveau/bios: add parsing of BIT M(v2) +0x03 table
drm/nouveau/core: allow vbios parsing without knowing chipset type
drm/nouveau/lib: add null backend
drm/nouveau/device: store revision
drm/nouveau/core: add some forgotten subdevs to disable mask
drm/gk20a/clk: fix max VCO value
drm/nouveau: we need pin_refcnt for nouveau_bo_placement_set()
drm/nv50-/kms: add some evo tracing ability for debugging
drm/nv50/kms: use sclass() instead of trial-and-error
...
Ben Skeggs [Mon, 10 Nov 2014 02:36:44 +0000 (12:36 +1000)]
drm/nv50/kms: drop requirement that framebuffer bos be contig up-front
We'll move them at pin() time if necessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 10 Nov 2014 05:52:02 +0000 (15:52 +1000)]
drm/nv50/kms: directly use cursor image from userspace buffer
Preparation for transition to planes, which use framebuffers for the
cursor image. We've always done copies from the userspace buffer up
until now for legacy reasons, there's no good reason to do so on the
chipsets this code covers.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 10 Nov 2014 02:35:06 +0000 (12:35 +1000)]
drm/nouveau/kms: when pinning display-related buffers, force contig vram
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 10 Nov 2014 01:24:27 +0000 (11:24 +1000)]
drm/nouveau: teach nouveau_bo_pin() how to force a contig vram allocation
We have the ability to move buffers around in the kernel if necessary,
and should probably use it rather than failing if userspace passes us
a non-contig buffer for a plane.
The NOUVEAU_GEM_TILE_NONCONTIG flag from userspace will become a mere
initial placement hint once all the relevant paths have been updated.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Vince Hsu [Tue, 2 Dec 2014 04:50:35 +0000 (12:50 +0800)]
drm/nouveau/volt: add support for GK20A
The voltage value are calculated by the hardware characterized
result.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Vince Hsu [Tue, 2 Dec 2014 04:50:34 +0000 (12:50 +0800)]
drm/nouveau/platform: add GPU speedo information to nouveau platform
For GK20A we need the GPU speedo value to calculate voltage levels.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Vince Hsu [Tue, 2 Dec 2014 04:50:33 +0000 (12:50 +0800)]
drm/nouveau/volt: allow non-bios voltage scaling
Move the vbios parsing out of init() and call it conditionally if the
platform has a vbios. Non-vbios platforms can use the ctor() to init the
data structures.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 25 Nov 2014 23:03:15 +0000 (09:03 +1000)]
drm/gf100-/gr: return non-fatal error code when fw not present
This allows the module to load without acceleration.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 25 Nov 2014 22:51:10 +0000 (08:51 +1000)]
drm/nouveau/devinit: bump priv ring timeouts before executing scripts
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 4 Nov 2014 05:13:30 +0000 (15:13 +1000)]
drm/nouveau/bios: translate ramcfg strap through M0203
A machine has been spotted where the ramcfg strap is "8", and the ramcfg
xlat table goes 0-7,0-7, resulting in us selecting config 0 for memory
items. On this particular system, config "8" is available and supposed
to be used. It appears that starting from GT21x (where Mv2 appears),
we're supposed to use the value in this table instead.
One concern here is that not all the places we currently use ramcfg xlat
are supposed to be treated the same now. The strap xlat table wasn't
removed from the vbios either, presumably for some kind of good reason.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 4 Nov 2014 03:04:35 +0000 (13:04 +1000)]
drm/nouveau/fb: make use of M0203 routines for ram type determination
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 4 Nov 2014 02:06:25 +0000 (12:06 +1000)]
drm/nouveau/bios: add parsing of BIT M(v2) +0x03 table
We only support one kind of matching here (ramcfg strap), but it appears
alternate methods are possible. I wrote a tool to scan our vbios repo
for other types, but did not see any used. Hopefully this means there
aren't any in the wild that will now break.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 18 Nov 2014 00:51:19 +0000 (10:51 +1000)]
drm/nouveau/core: allow vbios parsing without knowing chipset type
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 18 Nov 2014 00:36:59 +0000 (10:36 +1000)]
drm/nouveau/lib: add null backend
For the moment, just used to speed up vbios-only testing. Have some
ideas for extending in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 17 Nov 2014 12:56:37 +0000 (22:56 +1000)]
drm/nouveau/device: store revision
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 17 Nov 2014 12:52:11 +0000 (22:52 +1000)]
drm/nouveau/core: add some forgotten subdevs to disable mask
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alexandre Courbot [Thu, 13 Nov 2014 09:07:27 +0000 (18:07 +0900)]
drm/gk20a/clk: fix max VCO value
For some reason max_vco was set to a lower value that it can support,
which prevented some clock states to be applied. Fix this by setting it
to the same value as downstream.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 10 Nov 2014 01:12:17 +0000 (11:12 +1000)]
drm/nouveau: we need pin_refcnt for nouveau_bo_placement_set()
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 3 Nov 2014 06:43:59 +0000 (16:43 +1000)]
drm/nv50-/kms: add some evo tracing ability for debugging
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 3 Nov 2014 05:01:33 +0000 (15:01 +1000)]
drm/nv50/kms: use sclass() instead of trial-and-error
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Mon, 3 Nov 2014 04:33:01 +0000 (14:33 +1000)]
drm/nv50/kms: remove a couple of cursor-related stub functions
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Thu, 6 Nov 2014 04:34:31 +0000 (14:34 +1000)]
drm/nouveau: fix pin refcnt leak in failure path
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alexandre Courbot [Mon, 27 Oct 2014 09:49:19 +0000 (18:49 +0900)]
drm/nouveau: synchronize BOs when required
On architectures for which access to GPU memory is non-coherent,
caches need to be flushed and invalidated explicitly when BO control
changes between CPU and GPU.
This patch adds buffer synchronization functions which invokes the
correct API (PCI or DMA) to ensure synchronization is effective.
Based on the TTM DMA cache helper patches by Lucas Stach.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alexandre Courbot [Mon, 27 Oct 2014 09:49:18 +0000 (18:49 +0900)]
drm/nouveau: allocate GPFIFOs and fences coherently
Specify TTM_PL_FLAG_UNCACHED when allocating GPFIFOs and fences to
allow them to be safely accessed by the kernel without being synced
on non-coherent architectures.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alexandre Courbot [Mon, 27 Oct 2014 09:49:17 +0000 (18:49 +0900)]
drm/nouveau: implement explicitly coherent BOs
Allow nouveau_bo_new() to recognize the TTM_PL_FLAG_UNCACHED flag, which
means that we want the allocated BO to be perfectly coherent between the
CPU and GPU. This is useful on non-coherent architectures for which we
do not want to manually sync some rarely-accessed buffers: typically,
fences and pushbuffers.
A TTM BO allocated with the TTM_PL_FLAG_UNCACHED on a non-coherent
architecture will be populated using the DMA API, and accesses to it
performed using the coherent mapping performed by dma_alloc_coherent().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alexandre Courbot [Mon, 27 Oct 2014 09:49:16 +0000 (18:49 +0900)]
drm/nouveau: introduce nv_device_is_cpu_coherent()
Add a function allowing us to know whether a device is CPU-coherent,
i.e. accesses performed by the CPU on GPU-mapped buffers will
be immediately visible on the GPU side and vice-versa.
For now, a device is considered to be coherent if it uses the PCI bus on
a non-ARM architecture.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alexandre Courbot [Mon, 27 Oct 2014 09:11:52 +0000 (18:11 +0900)]
drm/nouveau: warn when moving a pinned object
Pinned BOs are supposed to remain in their current location until
unpinned. Display a warning for the supposedly-erroneous case where we
are trying to move such objects.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 28 Oct 2014 01:21:44 +0000 (11:21 +1000)]
drm/nouveau/disp: clear notify intr status when enabling, to prevent races
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Thu, 2 Oct 2014 05:25:25 +0000 (15:25 +1000)]
drm/nv50-/disp: rename class members to match nvidia channel names
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 21 Oct 2014 05:23:16 +0000 (15:23 +1000)]
drm/nouveau/core: remove some dead code that got forgotten
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Thu, 2 Oct 2014 16:01:58 +0000 (18:01 +0200)]
drm/nouveau/pwr/fuc: Fix thinko in nouveau_memx_wait()
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Thu, 2 Oct 2014 16:01:57 +0000 (18:01 +0200)]
drm/nva3/clock: Allow user reclocking
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Thu, 2 Oct 2014 16:01:56 +0000 (18:01 +0200)]
drm/nouveau/fb/ramnva3: Reclocking script for GDDR3
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Thu, 2 Oct 2014 16:01:55 +0000 (18:01 +0200)]
drm/nouveau/fb/ramnva3: Reclocking script for DDR2
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Thu, 2 Oct 2014 16:01:54 +0000 (18:01 +0200)]
drm/nouveau/fb/ramnva3: Reclocking script for DDR3
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Thu, 2 Oct 2014 16:01:53 +0000 (18:01 +0200)]
drm/nouveau/fb/ramnva3: Ressurect timing calculation code
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Thu, 2 Oct 2014 16:01:52 +0000 (18:01 +0200)]
drm/nouveau/fb/ramnva3: Link training for DDR3
V2: fix whitespace errors in memx.fuc
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>