OSDN Git Service
Heiner Kallweit [Wed, 30 Dec 2020 18:33:34 +0000 (19:33 +0100)]
r8169: work around power-saving bug on some chip versions
A user reported failing network with RTL8168dp (a quite rare chip
version). Realtek confirmed that few chip versions suffer from a PLL
power-down hw bug.
Fixes:
07df5bd874f0 ("r8169: power down chip in probe")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a1c39460-d533-7f9e-fa9d-2b8990b02426@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bjørn Mork [Wed, 30 Dec 2020 15:24:51 +0000 (16:24 +0100)]
net: usb: qmi_wwan: add Quectel EM160R-GL
New modem using ff/ff/30 for QCDM, ff/00/00 for AT and NMEA,
and ff/ff/ff for RMNET/QMI.
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=2c7c ProdID=0620 Rev= 4.09
S: Manufacturer=Quectel
S: Product=EM160R-GL
S: SerialNumber=
e31cedc1
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20201230152451.245271-1-bjorn@mork.no
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Wed, 30 Dec 2020 11:42:51 +0000 (13:42 +0200)]
selftests: mlxsw: Set headroom size of correct port
The test was setting the headroom size of the wrong port. This was not
visible because of a firmware bug that canceled this bug.
Set the headroom size of the correct port, so that the test will pass
with both old and new firmware versions.
Fixes:
bfa804784e32 ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20201230114251.394009-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Charles Keepax [Mon, 4 Jan 2021 10:38:02 +0000 (10:38 +0000)]
net: macb: Correct usage of MACB_CAPS_CLK_HW_CHG flag
A new flag MACB_CAPS_CLK_HW_CHG was added and all callers of
macb_set_tx_clk were gated on the presence of this flag.
- if (!clk)
+ if (!bp->tx_clk || !(bp->caps & MACB_CAPS_CLK_HW_CHG))
However the flag was not added to anything other than the new
sama7g5_gem, turning that function call into a no op for all other
systems. This breaks the networking on Zynq.
The commit message adding this states: a new capability so that
macb_set_tx_clock() to not be called for IPs having this
capability
This strongly implies that present of the flag was intended to skip
the function not absence of the flag. Update the if statement to
this effect, which repairs the existing users.
Fixes:
daafa1d33cc9 ("net: macb: add capability to not set the clock rate")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210104103802.13091-1-ckeepax@opensource.cirrus.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
YANG LI [Wed, 30 Dec 2020 07:23:14 +0000 (15:23 +0800)]
ibmvnic: fix: NULL pointer dereference.
The error is due to dereference a null pointer in function
reset_one_sub_crq_queue():
if (!scrq) {
netdev_dbg(adapter->netdev,
"Invalid scrq reset. irq (%d) or msgs(%p).\n",
scrq->irq, scrq->msgs);
return -EINVAL;
}
If the expression is true, scrq must be a null pointer and cannot
dereference.
Fixes:
9281cf2d5840 ("ibmvnic: avoid memset null scrq msgs")
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Reported-by: Abaci <abaci@linux.alibaba.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/1609312994-121032-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Baruch Siach [Tue, 29 Dec 2020 09:08:39 +0000 (11:08 +0200)]
docs: networking: packet_mmap: fix old config reference
Before commit
889b8f964f2f ("packet: Kill CONFIG_PACKET_MMAP.") there
used to be a CONFIG_PACKET_MMAP config symbol that depended on
CONFIG_PACKET. The text still implies that PACKET_MMAP can be disabled.
Remove that from the text, as well as reference to old kernel versions.
Also, drop reference to broken link to information for pre 2.6.5
kernels.
Make a slight working improvement (s/In/On/) while at it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/80089f3783372c8fd7833f28ce774a171b2ef252.1609232919.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Baruch Siach [Tue, 29 Dec 2020 09:08:38 +0000 (11:08 +0200)]
docs: networking: packet_mmap: fix formatting for C macros
The citation of macro definitions should appear in a code block.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/5cb47005e7a59b64299e038827e295822193384c.1609232919.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yunjian Wang [Tue, 29 Dec 2020 02:01:48 +0000 (10:01 +0800)]
vhost_net: fix ubuf refcount incorrectly when sendmsg fails
Currently the vhost_zerocopy_callback() maybe be called to decrease
the refcount when sendmsg fails in tun. The error handling in vhost
handle_tx_zerocopy() will try to decrease the same refcount again.
This is wrong. To fix this issue, we only call vhost_net_ubuf_put()
when vq->heads[nvq->desc].len == VHOST_DMA_IN_PROGRESS.
Fixes:
bab632d69ee4 ("vhost: vhost TX zero-copy support")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/1609207308-20544-1-git-send-email-wangyunjian@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Taehee Yoo [Mon, 28 Dec 2020 15:21:46 +0000 (15:21 +0000)]
bareudp: Fix use of incorrect min_headroom size
In the bareudp6_xmit_skb(), it calculates min_headroom.
At that point, it uses struct iphdr, but it's not correct.
So panic could occur.
The struct ipv6hdr should be used.
Test commands:
ip netns add A
ip netns add B
ip link add veth0 netns A type veth peer name veth1 netns B
ip netns exec A ip link set veth0 up
ip netns exec A ip a a 2001:db8:0::1/64 dev veth0
ip netns exec B ip link set veth1 up
ip netns exec B ip a a 2001:db8:0::2/64 dev veth1
for i in {10..1}
do
let A=$i-1
ip netns exec A ip link add bareudp$i type bareudp dstport $i \
ethertype 0x86dd
ip netns exec A ip link set bareudp$i up
ip netns exec A ip -6 a a 2001:db8:$i::1/64 dev bareudp$i
ip netns exec A ip -6 r a 2001:db8:$i::2 encap ip6 src \
2001:db8:$A::1 dst 2001:db8:$A::2 via 2001:db8:$i::2 \
dev bareudp$i
ip netns exec B ip link add bareudp$i type bareudp dstport $i \
ethertype 0x86dd
ip netns exec B ip link set bareudp$i up
ip netns exec B ip -6 a a 2001:db8:$i::2/64 dev bareudp$i
ip netns exec B ip -6 r a 2001:db8:$i::1 encap ip6 src \
2001:db8:$A::2 dst 2001:db8:$A::1 via 2001:db8:$i::1 \
dev bareudp$i
done
ip netns exec A ping 2001:db8:7::2
Splat looks like:
[ 66.436679][ C2] skbuff: skb_under_panic: text:
ffffffff928614c8 len:454 put:14 head:
ffff88810abb4000 data:
ffff88810abb3ffa tail:0x1c0 end:0x3ec0 dev:veth0
[ 66.441626][ C2] ------------[ cut here ]------------
[ 66.443458][ C2] kernel BUG at net/core/skbuff.c:109!
[ 66.445313][ C2] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 66.447606][ C2] CPU: 2 PID: 913 Comm: ping Not tainted 5.10.0+ #819
[ 66.450251][ C2] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 66.453713][ C2] RIP: 0010:skb_panic+0x15d/0x15f
[ 66.455345][ C2] Code: 98 fe 4c 8b 4c 24 10 53 8b 4d 70 45 89 e0 48 c7 c7 60 8b 78 93 41 57 41 56 41 55 48 8b 54 24 20 48 8b 74 24 28 e8 b5 40 f9 ff <0f> 0b 48 8b 6c 24 20 89 34 24 e8 08 c9 98 fe 8b 34 24 48 c7 c1 80
[ 66.462314][ C2] RSP: 0018:
ffff888119209648 EFLAGS:
00010286
[ 66.464281][ C2] RAX:
0000000000000089 RBX:
ffff888003159000 RCX:
0000000000000000
[ 66.467216][ C2] RDX:
0000000000000089 RSI:
0000000000000008 RDI:
ffffed10232412c0
[ 66.469768][ C2] RBP:
ffff88810a53d440 R08:
ffffed102328018d R09:
ffffed102328018d
[ 66.472297][ C2] R10:
ffff888119400c67 R11:
ffffed102328018c R12:
000000000000000e
[ 66.474833][ C2] R13:
ffff88810abb3ffa R14:
00000000000001c0 R15:
0000000000003ec0
[ 66.477361][ C2] FS:
00007f37c0c72f00(0000) GS:
ffff888119200000(0000) knlGS:
0000000000000000
[ 66.480214][ C2] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 66.482296][ C2] CR2:
000055a058808570 CR3:
000000011039e002 CR4:
00000000003706e0
[ 66.484811][ C2] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 66.487793][ C2] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 66.490424][ C2] Call Trace:
[ 66.491469][ C2] <IRQ>
[ 66.492374][ C2] ? eth_header+0x28/0x190
[ 66.494054][ C2] ? eth_header+0x28/0x190
[ 66.495401][ C2] skb_push.cold.99+0x22/0x22
[ 66.496700][ C2] eth_header+0x28/0x190
[ 66.497867][ C2] neigh_resolve_output+0x3de/0x720
[ 66.499615][ C2] ? __neigh_update+0x7e8/0x20a0
[ 66.501176][ C2] __neigh_update+0x8bd/0x20a0
[ 66.502749][ C2] ndisc_update+0x34/0xc0
[ 66.504010][ C2] ndisc_recv_na+0x8da/0xb80
[ 66.505041][ C2] ? pndisc_redo+0x20/0x20
[ 66.505888][ C2] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 66.506965][ C2] ndisc_rcv+0x3a0/0x470
[ 66.507797][ C2] icmpv6_rcv+0xad9/0x1b00
[ 66.508645][ C2] ip6_protocol_deliver_rcu+0xcd6/0x1560
[ 66.509719][ C2] ip6_input_finish+0x5b/0xf0
[ 66.510615][ C2] ip6_input+0xcd/0x2d0
[ 66.511406][ C2] ? ip6_input_finish+0xf0/0xf0
[ 66.512327][ C2] ? rcu_read_lock_held+0x91/0xa0
[ 66.513279][ C2] ? ip6_protocol_deliver_rcu+0x1560/0x1560
[ 66.514414][ C2] ipv6_rcv+0xe8/0x300
[ ... ]
Acked-by: Guillaume Nault <gnault@redhat.com>
Fixes:
571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20201228152146.24270-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Taehee Yoo [Mon, 28 Dec 2020 15:21:36 +0000 (15:21 +0000)]
bareudp: set NETIF_F_LLTX flag
Like other tunneling interfaces, the bareudp doesn't need TXLOCK.
So, It is good to set the NETIF_F_LLTX flag to improve performance and
to avoid lockdep's false-positive warning.
Test commands:
ip netns add A
ip netns add B
ip link add veth0 netns A type veth peer name veth1 netns B
ip netns exec A ip link set veth0 up
ip netns exec A ip a a 10.0.0.1/24 dev veth0
ip netns exec B ip link set veth1 up
ip netns exec B ip a a 10.0.0.2/24 dev veth1
for i in {2..1}
do
let A=$i-1
ip netns exec A ip link add bareudp$i type bareudp \
dstport $i ethertype ip
ip netns exec A ip link set bareudp$i up
ip netns exec A ip a a 10.0.$i.1/24 dev bareudp$i
ip netns exec A ip r a 10.0.$i.2 encap ip src 10.0.$A.1 \
dst 10.0.$A.2 via 10.0.$i.2 dev bareudp$i
ip netns exec B ip link add bareudp$i type bareudp \
dstport $i ethertype ip
ip netns exec B ip link set bareudp$i up
ip netns exec B ip a a 10.0.$i.2/24 dev bareudp$i
ip netns exec B ip r a 10.0.$i.1 encap ip src 10.0.$A.2 \
dst 10.0.$A.1 via 10.0.$i.1 dev bareudp$i
done
ip netns exec A ping 10.0.2.2
Splat looks like:
[ 96.992803][ T822] ============================================
[ 96.993954][ T822] WARNING: possible recursive locking detected
[ 96.995102][ T822] 5.10.0+ #819 Not tainted
[ 96.995927][ T822] --------------------------------------------
[ 96.997091][ T822] ping/822 is trying to acquire lock:
[ 96.998083][ T822]
ffff88810f753898 (_xmit_NONE#2){+.-.}-{2:2}, at: __dev_queue_xmit+0x1f52/0x2960
[ 96.999813][ T822]
[ 96.999813][ T822] but task is already holding lock:
[ 97.001192][ T822]
ffff88810c385498 (_xmit_NONE#2){+.-.}-{2:2}, at: __dev_queue_xmit+0x1f52/0x2960
[ 97.002908][ T822]
[ 97.002908][ T822] other info that might help us debug this:
[ 97.004401][ T822] Possible unsafe locking scenario:
[ 97.004401][ T822]
[ 97.005784][ T822] CPU0
[ 97.006407][ T822] ----
[ 97.007010][ T822] lock(_xmit_NONE#2);
[ 97.007779][ T822] lock(_xmit_NONE#2);
[ 97.008550][ T822]
[ 97.008550][ T822] *** DEADLOCK ***
[ 97.008550][ T822]
[ 97.010057][ T822] May be due to missing lock nesting notation
[ 97.010057][ T822]
[ 97.011594][ T822] 7 locks held by ping/822:
[ 97.012426][ T822] #0:
ffff888109a144f0 (sk_lock-AF_INET){+.+.}-{0:0}, at: raw_sendmsg+0x12f7/0x2b00
[ 97.014191][ T822] #1:
ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: ip_finish_output2+0x249/0x2020
[ 97.016045][ T822] #2:
ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x1fd/0x2960
[ 97.017897][ T822] #3:
ffff88810c385498 (_xmit_NONE#2){+.-.}-{2:2}, at: __dev_queue_xmit+0x1f52/0x2960
[ 97.019684][ T822] #4:
ffffffffbce2f600 (rcu_read_lock){....}-{1:2}, at: bareudp_xmit+0x31b/0x3690 [bareudp]
[ 97.021573][ T822] #5:
ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: ip_finish_output2+0x249/0x2020
[ 97.023424][ T822] #6:
ffffffffbce2f5a0 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x1fd/0x2960
[ 97.025259][ T822]
[ 97.025259][ T822] stack backtrace:
[ 97.026349][ T822] CPU: 3 PID: 822 Comm: ping Not tainted 5.10.0+ #819
[ 97.027609][ T822] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 97.029407][ T822] Call Trace:
[ 97.030015][ T822] dump_stack+0x99/0xcb
[ 97.030783][ T822] __lock_acquire.cold.77+0x149/0x3a9
[ 97.031773][ T822] ? stack_trace_save+0x81/0xa0
[ 97.032661][ T822] ? register_lock_class+0x1910/0x1910
[ 97.033673][ T822] ? register_lock_class+0x1910/0x1910
[ 97.034679][ T822] ? rcu_read_lock_sched_held+0x91/0xc0
[ 97.035697][ T822] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 97.036690][ T822] lock_acquire+0x1b2/0x730
[ 97.037515][ T822] ? __dev_queue_xmit+0x1f52/0x2960
[ 97.038466][ T822] ? check_flags+0x50/0x50
[ 97.039277][ T822] ? netif_skb_features+0x296/0x9c0
[ 97.040226][ T822] ? validate_xmit_skb+0x29/0xb10
[ 97.041151][ T822] _raw_spin_lock+0x30/0x70
[ 97.041977][ T822] ? __dev_queue_xmit+0x1f52/0x2960
[ 97.042927][ T822] __dev_queue_xmit+0x1f52/0x2960
[ 97.043852][ T822] ? netdev_core_pick_tx+0x290/0x290
[ 97.044824][ T822] ? mark_held_locks+0xb7/0x120
[ 97.045712][ T822] ? lockdep_hardirqs_on_prepare+0x12c/0x3e0
[ 97.046824][ T822] ? __local_bh_enable_ip+0xa5/0xf0
[ 97.047771][ T822] ? ___neigh_create+0x12a8/0x1eb0
[ 97.048710][ T822] ? trace_hardirqs_on+0x41/0x120
[ 97.049626][ T822] ? ___neigh_create+0x12a8/0x1eb0
[ 97.050556][ T822] ? __local_bh_enable_ip+0xa5/0xf0
[ 97.051509][ T822] ? ___neigh_create+0x12a8/0x1eb0
[ 97.052443][ T822] ? check_chain_key+0x244/0x5f0
[ 97.053352][ T822] ? rcu_read_lock_bh_held+0x56/0xa0
[ 97.054317][ T822] ? ip_finish_output2+0x6ea/0x2020
[ 97.055263][ T822] ? pneigh_lookup+0x410/0x410
[ 97.056135][ T822] ip_finish_output2+0x6ea/0x2020
[ ... ]
Acked-by: Guillaume Nault <gnault@redhat.com>
Fixes:
571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20201228152136.24215-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David S. Miller [Mon, 28 Dec 2020 23:20:48 +0000 (15:20 -0800)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2020-12-28
The following pull-request contains BPF updates for your *net* tree.
There is a small merge conflict between bpf tree commit
69ca310f3416
("bpf: Save correct stopping point in file seq iteration") and net tree
commit
66ed594409a1 ("bpf/task_iter: In task_file_seq_get_next use
task_lookup_next_fd_rcu"). The get_files_struct() does not exist anymore
in net, so take the hunk in HEAD and add the `info->tid = curr_tid` to
the error path:
[...]
curr_task = task_seq_get_next(ns, &curr_tid, true);
if (!curr_task) {
info->task = NULL;
info->tid = curr_tid;
return NULL;
}
/* set info->task and info->tid */
[...]
We've added 10 non-merge commits during the last 9 day(s) which contain
a total of 11 files changed, 75 insertions(+), 20 deletions(-).
The main changes are:
1) Various AF_XDP fixes such as fill/completion ring leak on failed bind and
fixing a race in skb mode's backpressure mechanism, from Magnus Karlsson.
2) Fix latency spikes on lockdep enabled kernels by adding a rescheduling
point to BPF hashtab initialization, from Eric Dumazet.
3) Fix a splat in task iterator by saving the correct stopping point in the
seq file iteration, from Jonathan Lemon.
4) Fix BPF maps selftest by adding retries in case hashtab returns EBUSY
errors on update/deletes, from Andrii Nakryiko.
5) Fix BPF selftest error reporting to something more user friendly if the
vmlinux BTF cannot be found, from Kamal Mostafa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xie He [Mon, 28 Dec 2020 02:53:39 +0000 (18:53 -0800)]
net: hdlc_ppp: Fix issues when mod_timer is called while timer is running
ppp_cp_event is called directly or indirectly by ppp_rx with "ppp->lock"
held. It may call mod_timer to add a new timer. However, at the same time
ppp_timer may be already running and waiting for "ppp->lock". In this
case, there's no need for ppp_timer to continue running and it can just
exit.
If we let ppp_timer continue running, it may call add_timer. This causes
kernel panic because add_timer can't be called with a timer pending.
This patch fixes this problem.
Fixes:
e022c2f07ae5 ("WAN: new synchronous PPP implementation for generic HDLC.")
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Léo Le Bouter [Sun, 27 Dec 2020 16:11:36 +0000 (17:11 +0100)]
atlantic: remove architecture depends
This was tested on a RaptorCS Talos II with IBM POWER9 DD2.2 CPUs and an
ASUS XG-C100F PCI-e card without any issue. Speeds of ~8Gbps could be
attained with not-very-scientific (wget HTTP) both-ways measurements on
a local network. No warning or error reported in kernel logs. The
drivers seems to be portable enough for it not to be gated like such.
Signed-off-by: Léo Le Bouter <lle-bout@zaclys.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 26 Dec 2020 23:44:53 +0000 (15:44 -0800)]
erspan: fix version 1 check in gre_parse_header()
Both version 0 and version 1 use ETH_P_ERSPAN, but version 0 does not
have an erspan header. So the check in gre_parse_header() is wrong,
we have to distinguish version 1 from version 0.
We can just check the gre header length like is_erspan_type1().
Fixes:
cb73ee40b1b3 ("net: ip_gre: use erspan key field for tunnel lookup")
Reported-by: syzbot+f583ce3d4ddf9836b27a@syzkaller.appspotmail.com
Cc: William Tu <u9012063@gmail.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunjian Wang [Sat, 26 Dec 2020 08:10:05 +0000 (16:10 +0800)]
net: hns: fix return value check in __lb_other_process()
The function skb_copy() could return NULL, the return value
need to be checked.
Fixes:
b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Fri, 25 Dec 2020 06:23:44 +0000 (22:23 -0800)]
net: sched: prevent invalid Scell_log shift count
Check Scell_log shift size in red_check_params() and modify all callers
of red_check_params() to pass Scell_log.
This prevents a shift out-of-bounds as detected by UBSAN:
UBSAN: shift-out-of-bounds in ./include/net/red.h:252:22
shift exponent 72 is too large for 32-bit type 'int'
Fixes:
8afa10cbe281 ("net_sched: red: Avoid illegal values")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+97c5bd9cc81eca63d36e@syzkaller.appspotmail.com
Cc: Nogah Frankel <nogahf@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
weichenchen [Fri, 25 Dec 2020 05:44:45 +0000 (13:44 +0800)]
net: neighbor: fix a crash caused by mod zero
pneigh_enqueue() tries to obtain a random delay by mod
NEIGH_VAR(p, PROXY_DELAY). However, NEIGH_VAR(p, PROXY_DELAY)
migth be zero at that point because someone could write zero
to /proc/sys/net/ipv4/neigh/[device]/proxy_delay after the
callers check it.
This patch uses prandom_u32_max() to get a random delay instead
which avoids potential division by zero.
Signed-off-by: weichenchen <weichen.chen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Thu, 24 Dec 2020 19:01:09 +0000 (20:01 +0100)]
ipv4: Ignore ECN bits for fib lookups in fib_compute_spec_dst()
RT_TOS() only clears one of the ECN bits. Therefore, when
fib_compute_spec_dst() resorts to a fib lookup, it can return
different results depending on the value of the second ECN bit.
For example, ECT(0) and ECT(1) packets could be treated differently.
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/24 dev veth01
$ ip -netns ns1 address add 192.0.2.11/24 dev veth10
$ ip -netns ns1 address add 192.0.2.21/32 dev lo
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10 src 192.0.2.21
$ ip netns exec ns1 sysctl -wq net.ipv4.icmp_echo_ignore_broadcasts=0
With TOS 4 and ECT(1), ns1 replies using source address 192.0.2.21
(ping uses -Q to set all TOS and ECN bits):
$ ip netns exec ns0 ping -c 1 -b -Q 5 192.0.2.255
[...]
64 bytes from 192.0.2.21: icmp_seq=1 ttl=64 time=0.544 ms
But with TOS 4 and ECT(0), ns1 replies using source address 192.0.2.11
because the "tos 4" route isn't matched:
$ ip netns exec ns0 ping -c 1 -b -Q 6 192.0.2.255
[...]
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.597 ms
After this patch the ECN bits don't affect the result anymore:
$ ip netns exec ns0 ping -c 1 -b -Q 6 192.0.2.255
[...]
64 bytes from 192.0.2.21: icmp_seq=1 ttl=64 time=0.591 ms
Fixes:
35ebf65e851c ("ipv4: Create and use fib_compute_spec_dst() helper.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Chulski [Wed, 23 Dec 2020 18:35:21 +0000 (20:35 +0200)]
net: mvpp2: fix pkt coalescing int-threshold configuration
The packet coalescing interrupt threshold has separated registers
for different aggregated/cpu (sw-thread). The required value should
be loaded for every thread but not only for 1 current cpu.
Fixes:
213f428f5056 ("net: mvpp2: add support for TX interrupts and RX queue distribution modes")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608748521-11033-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Dec 2020 22:13:24 +0000 (14:13 -0800)]
Merge branch 'net-ipa-fix-some-new-build-warnings'
Alex Elder says:
====================
net: ipa: fix some new build warnings
I got a super friendly message from the Intel kernel test robot that
pointed out that two patches I posted last week caused new build
warnings. I already had these problems fixed in my own tree but
the fix was not included in what I sent out last week.
====================
Link: https://lore.kernel.org/r/20201226213737.338928-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Sat, 26 Dec 2020 21:37:37 +0000 (15:37 -0600)]
net: ipa: don't return a value from evt_ring_command()
Callers of evt_ring_command() no longer care whether the command
times out, and don't use what evt_ring_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes:
428b448ee764a ("net: ipa: use state to determine event ring command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Sat, 26 Dec 2020 21:37:36 +0000 (15:37 -0600)]
net: ipa: don't return a value from gsi_channel_command()
Callers of gsi_channel_command() no longer care whether the command
times out, and don't use what gsi_channel_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes:
6ffddf3b3d182 ("net: ipa: use state to determine channel command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Dec 2020 22:10:57 +0000 (14:10 -0800)]
Merge branch 'bnxt_en-bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
The first patch fixes recovery of fatal AER errors. The second one
fixes a potential array out of bounds issue.
====================
Link: https://lore.kernel.org/r/1609096698-15009-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Sun, 27 Dec 2020 19:18:18 +0000 (14:18 -0500)]
bnxt_en: Check TQM rings for maximum supported value.
TQM rings are hardware resources that require host context memory
managed by the driver. The driver supports up to 9 TQM rings and
the number of rings to use is requested by firmware during run-time.
Cap this number to the maximum supported to prevent accessing beyond
the array. Future firmware may request more than 9 TQM rings. Define
macros to remove the magic number 9 from the C code.
Fixes:
ac3158cb0108 ("bnxt_en: Allocate TQM ring context memory according to fw specification.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vasundhara Volam [Sun, 27 Dec 2020 19:18:17 +0000 (14:18 -0500)]
bnxt_en: Fix AER recovery.
A recent change skips sending firmware messages to the firmware when
pci_channel_offline() is true during fatal AER error. To make this
complete, we need to move the re-initialization sequence to
bnxt_io_resume(), otherwise the firmware messages to re-initialize
will all be skipped. In any case, it is more correct to re-initialize
in bnxt_io_resume().
Also, fix the reverse x-mas tree format when defining variables
in bnxt_io_slot_reset().
Fixes:
b340dc680ed4 ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Dec 2020 22:04:03 +0000 (14:04 -0800)]
Merge branch '1GbE' of git://git./linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-12-23
Commit
e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME
systems") disabled S0ix flows for systems that have various incarnations of
the i219-LM ethernet controller. This was done because of some regressions
caused by an earlier commit
632fbd5eb5b0e ("e1000e: fix S0ix flows for
cable connected case") with i219-LM controller.
Per discussion with Intel architecture team this direction should be
changed and allow S0ix flows to be used by default. This patch series
includes directional changes for their conclusions in
https://lkml.org/lkml/2020/12/13/15.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: Export S0ix flags to ethtool
Revert "e1000e: disable s0ix entry and exit flows for ME systems"
e1000e: bump up timeout to wait when ME un-configures ULP mode
e1000e: Only run S0ix flows if shutdown succeeded
====================
Link: https://lore.kernel.org/r/20201223233625.92519-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Davide Caratti [Mon, 21 Dec 2020 21:07:25 +0000 (22:07 +0100)]
net: mptcp: cap forward allocation to 1M
the following syzkaller reproducer:
r0 = socket$inet_mptcp(0x2, 0x1, 0x106)
bind$inet(r0, &(0x7f0000000080)={0x2, 0x4e24, @multicast2}, 0x10)
connect$inet(r0, &(0x7f0000000480)={0x2, 0x4e24, @local}, 0x10)
sendto$inet(r0, &(0x7f0000000100)="f6", 0xffffffe7, 0xc000, 0x0, 0x0)
systematically triggers the following warning:
WARNING: CPU: 2 PID: 8618 at net/core/stream.c:208 sk_stream_kill_queues+0x3fa/0x580
Modules linked in:
CPU: 2 PID: 8618 Comm: syz-executor Not tainted 5.10.0+ #334
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.1-4.module+el8.1.0+4066+
0f1aadab 04/04
RIP: 0010:sk_stream_kill_queues+0x3fa/0x580
Code: df 48 c1 ea 03 0f b6 04 02 84 c0 74 04 3c 03 7e 40 8b ab 20 02 00 00 e9 64 ff ff ff e8 df f0 81 2
RSP: 0018:
ffffc9000290fcb0 EFLAGS:
00010293
RAX:
ffff888011cb8000 RBX:
0000000000000000 RCX:
ffffffff86eecf0e
RDX:
0000000000000000 RSI:
ffffffff86eecf6a RDI:
0000000000000005
RBP:
0000000000000e28 R08:
ffff888011cb8000 R09:
fffffbfff1f48139
R10:
ffffffff8fa409c7 R11:
fffffbfff1f48138 R12:
ffff8880215e6220
R13:
ffffffff8fa409c0 R14:
ffffc9000290fd30 R15:
1ffff92000521fa2
FS:
00007f41c78f4800(0000) GS:
ffff88802d000000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f95c803d088 CR3:
0000000025ed2000 CR4:
00000000000006f0
Call Trace:
__mptcp_destroy_sock+0x4f5/0x8e0
mptcp_close+0x5e2/0x7f0
inet_release+0x12b/0x270
__sock_release+0xc8/0x270
sock_close+0x18/0x20
__fput+0x272/0x8e0
task_work_run+0xe0/0x1a0
exit_to_user_mode_prepare+0x1df/0x200
syscall_exit_to_user_mode+0x19/0x50
entry_SYSCALL_64_after_hwframe+0x44/0xa9
userspace programs provide arbitrarily high values of 'len' in sendmsg():
this is causing integer overflow of 'amount'. Cap forward allocation to 1
megabyte: higher values are not really useful.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Fixes:
e93da92896bc ("mptcp: implement wmem reservation")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/3334d00d8b2faecafdfab9aa593efcbf61442756.1608584474.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yunjian Wang [Fri, 25 Dec 2020 02:52:16 +0000 (10:52 +0800)]
tun: fix return value when the number of iovs exceeds MAX_SKB_FRAGS
Currently the tun_napi_alloc_frags() function returns -ENOMEM when the
number of iovs exceeds MAX_SKB_FRAGS + 1. However this is inappropriate,
we should use -EMSGSIZE instead of -ENOMEM.
The following distinctions are matters:
1. the caller need to drop the bad packet when -EMSGSIZE is returned,
which means meeting a persistent failure.
2. the caller can try again when -ENOMEM is returned, which means
meeting a transient failure.
Fixes:
90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/1608864736-24332-1-git-send-email-wangyunjian@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Grygorii Strashko [Thu, 24 Dec 2020 16:24:05 +0000 (18:24 +0200)]
net: ethernet: ti: cpts: fix ethtool output when no ptp_clock registered
The CPTS driver registers PTP PHC clock when first netif is going up and
unregister it when all netif are down. Now ethtool will show:
- PTP PHC clock index 0 after boot until first netif is up;
- the last assigned PTP PHC clock index even if PTP PHC clock is not
registered any more after all netifs are down.
This patch ensures that -1 is returned by ethtool when PTP PHC clock is not
registered any more.
Fixes:
8a2c9a5ab4b9 ("net: ethernet: ti: cpts: rework initialization/deinitialization")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201224162405.28032-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Dec 2020 21:26:48 +0000 (13:26 -0800)]
Merge branch 'net-sysfs-fix-race-conditions-in-the-xps-code'
Antoine Tenart says:
====================
net-sysfs: fix race conditions in the xps code
This series fixes race conditions in the xps code, where out of bound
accesses can occur when dev->num_tc is updated, triggering oops. The
root cause is linked to locking issues. An explanation is given in each
of the commit logs.
We had a discussion on the v1 of this series about using the xps_map
mutex instead of the rtnl lock. While that seemed a better compromise,
v2 showed the added complexity wasn't best for fixes. So we decided to
go back to v1 and use the rtnl lock.
Because of this, the only differences between v1 and v3 are improvements
in the commit messages.
====================
Link: https://lore.kernel.org/r/20201223212323.3603139-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Antoine Tenart [Wed, 23 Dec 2020 21:23:23 +0000 (22:23 +0100)]
net-sysfs: take the rtnl lock when accessing xps_rxqs_map and num_tc
Accesses to dev->xps_rxqs_map (when using dev->num_tc) should be
protected by the rtnl lock, like we do for netif_set_xps_queue. I didn't
see an actual bug being triggered, but let's be safe here and take the
rtnl lock while accessing the map in sysfs.
Fixes:
8af2c06ff4b1 ("net-sysfs: Add interface for Rx queue(s) map per Tx queue")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Antoine Tenart [Wed, 23 Dec 2020 21:23:22 +0000 (22:23 +0100)]
net-sysfs: take the rtnl lock when storing xps_rxqs
Two race conditions can be triggered when storing xps rxqs, resulting in
various oops and invalid memory accesses:
1. Calling netdev_set_num_tc while netif_set_xps_queue:
- netif_set_xps_queue uses dev->tc_num as one of the parameters to
compute the size of new_dev_maps when allocating it. dev->tc_num is
also used to access the map, and the compiler may generate code to
retrieve this field multiple times in the function.
- netdev_set_num_tc sets dev->tc_num.
If new_dev_maps is allocated using dev->tc_num and then dev->tc_num
is set to a higher value through netdev_set_num_tc, later accesses to
new_dev_maps in netif_set_xps_queue could lead to accessing memory
outside of new_dev_maps; triggering an oops.
2. Calling netif_set_xps_queue while netdev_set_num_tc is running:
2.1. netdev_set_num_tc starts by resetting the xps queues,
dev->tc_num isn't updated yet.
2.2. netif_set_xps_queue is called, setting up the map with the
*old* dev->num_tc.
2.3. netdev_set_num_tc updates dev->tc_num.
2.4. Later accesses to the map lead to out of bound accesses and
oops.
A similar issue can be found with netdev_reset_tc.
One way of triggering this is to set an iface up (for which the driver
uses netdev_set_num_tc in the open path, such as bnx2x) and writing to
xps_rxqs in a concurrent thread. With the right timing an oops is
triggered.
Both issues have the same fix: netif_set_xps_queue, netdev_set_num_tc
and netdev_reset_tc should be mutually exclusive. We do that by taking
the rtnl lock in xps_rxqs_store.
Fixes:
8af2c06ff4b1 ("net-sysfs: Add interface for Rx queue(s) map per Tx queue")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Antoine Tenart [Wed, 23 Dec 2020 21:23:21 +0000 (22:23 +0100)]
net-sysfs: take the rtnl lock when accessing xps_cpus_map and num_tc
Accesses to dev->xps_cpus_map (when using dev->num_tc) should be
protected by the rtnl lock, like we do for netif_set_xps_queue. I didn't
see an actual bug being triggered, but let's be safe here and take the
rtnl lock while accessing the map in sysfs.
Fixes:
184c449f91fe ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Antoine Tenart [Wed, 23 Dec 2020 21:23:20 +0000 (22:23 +0100)]
net-sysfs: take the rtnl lock when storing xps_cpus
Two race conditions can be triggered when storing xps cpus, resulting in
various oops and invalid memory accesses:
1. Calling netdev_set_num_tc while netif_set_xps_queue:
- netif_set_xps_queue uses dev->tc_num as one of the parameters to
compute the size of new_dev_maps when allocating it. dev->tc_num is
also used to access the map, and the compiler may generate code to
retrieve this field multiple times in the function.
- netdev_set_num_tc sets dev->tc_num.
If new_dev_maps is allocated using dev->tc_num and then dev->tc_num
is set to a higher value through netdev_set_num_tc, later accesses to
new_dev_maps in netif_set_xps_queue could lead to accessing memory
outside of new_dev_maps; triggering an oops.
2. Calling netif_set_xps_queue while netdev_set_num_tc is running:
2.1. netdev_set_num_tc starts by resetting the xps queues,
dev->tc_num isn't updated yet.
2.2. netif_set_xps_queue is called, setting up the map with the
*old* dev->num_tc.
2.3. netdev_set_num_tc updates dev->tc_num.
2.4. Later accesses to the map lead to out of bound accesses and
oops.
A similar issue can be found with netdev_reset_tc.
One way of triggering this is to set an iface up (for which the driver
uses netdev_set_num_tc in the open path, such as bnx2x) and writing to
xps_cpus in a concurrent thread. With the right timing an oops is
triggered.
Both issues have the same fix: netif_set_xps_queue, netdev_set_num_tc
and netdev_reset_tc should be mutually exclusive. We do that by taking
the rtnl lock in xps_cpus_store.
Fixes:
184c449f91fe ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Roland Dreier [Thu, 24 Dec 2020 03:21:16 +0000 (19:21 -0800)]
CDC-NCM: remove "connected" log message
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonathan Lemon [Fri, 18 Dec 2020 18:50:31 +0000 (10:50 -0800)]
bpf: Use thread_group_leader()
Instead of directly comparing task->tgid and task->pid, use the
thread_group_leader() helper. This helps with readability, and
there should be no functional change.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201218185032.2464558-3-jonathan.lemon@gmail.com
Jonathan Lemon [Fri, 18 Dec 2020 18:50:30 +0000 (10:50 -0800)]
bpf: Save correct stopping point in file seq iteration
On some systems, some variant of the following splat is
repeatedly seen. The common factor in all traces seems
to be the entry point to task_file_seq_next(). With the
patch, all warnings go away.
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: \x0926-....: (20992 ticks this GP) idle=d7e/1/0x4000000000000002 softirq=
81556231/
81556231 fqs=4876
\x09(t=21033 jiffies g=
159148529 q=223125)
NMI backtrace for cpu 26
CPU: 26 PID:
2015853 Comm: bpftool Kdump: loaded Not tainted 5.6.13-0_fbk4_3876_gd8d1f9bf80bb #1
Hardware name: Quanta Twin Lakes MP/Twin Lakes Passive MP, BIOS F09_3A12 10/08/2018
Call Trace:
<IRQ>
dump_stack+0x50/0x70
nmi_cpu_backtrace.cold.6+0x13/0x50
? lapic_can_unplug_cpu.cold.30+0x40/0x40
nmi_trigger_cpumask_backtrace+0xba/0xca
rcu_dump_cpu_stacks+0x99/0xc7
rcu_sched_clock_irq.cold.90+0x1b4/0x3aa
? tick_sched_do_timer+0x60/0x60
update_process_times+0x24/0x50
tick_sched_timer+0x37/0x70
__hrtimer_run_queues+0xfe/0x270
hrtimer_interrupt+0xf4/0x210
smp_apic_timer_interrupt+0x5e/0x120
apic_timer_interrupt+0xf/0x20
</IRQ>
RIP: 0010:get_pid_task+0x38/0x80
Code: 89 f6 48 8d 44 f7 08 48 8b 00 48 85 c0 74 2b 48 83 c6 55 48 c1 e6 04 48 29 f0 74 19 48 8d 78 20 ba 01 00 00 00 f0 0f c1 50 20 <85> d2 74 27 78 11 83 c2 01 78 0c 48 83 c4 08 c3 31 c0 48 83 c4 08
RSP: 0018:
ffffc9000d293dc8 EFLAGS:
00000202 ORIG_RAX:
ffffffffffffff13
RAX:
ffff888637c05600 RBX:
ffffc9000d293e0c RCX:
0000000000000000
RDX:
0000000000000001 RSI:
0000000000000550 RDI:
ffff888637c05620
RBP:
ffffffff8284eb80 R08:
ffff88831341d300 R09:
ffff88822ffd8248
R10:
ffff88822ffd82d0 R11:
00000000003a93c0 R12:
0000000000000001
R13:
00000000ffffffff R14:
ffff88831341d300 R15:
0000000000000000
? find_ge_pid+0x1b/0x20
task_seq_get_next+0x52/0xc0
task_file_seq_get_next+0x159/0x220
task_file_seq_next+0x4f/0xa0
bpf_seq_read+0x159/0x390
vfs_read+0x8a/0x140
ksys_read+0x59/0xd0
do_syscall_64+0x42/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f95ae73e76e
Code: Bad RIP value.
RSP: 002b:
00007ffc02c1dbf8 EFLAGS:
00000246 ORIG_RAX:
0000000000000000
RAX:
ffffffffffffffda RBX:
000000000170faa0 RCX:
00007f95ae73e76e
RDX:
0000000000001000 RSI:
00007ffc02c1dc30 RDI:
0000000000000007
RBP:
00007ffc02c1ec70 R08:
0000000000000005 R09:
0000000000000006
R10:
fffffffffffff20b R11:
0000000000000246 R12:
00000000019112a0
R13:
0000000000000000 R14:
0000000000000007 R15:
00000000004283c0
If unable to obtain the file structure for the current task,
proceed to the next task number after the one returned from
task_seq_get_next(), instead of the next task number from the
original iterator.
Also, save the stopping task number from task_seq_get_next()
on failure in case of restarts.
Fixes:
eaaacd23910f ("bpf: Add task and task/file iterator targets")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201218185032.2464558-2-jonathan.lemon@gmail.com
Andrii Nakryiko [Wed, 23 Dec 2020 20:06:52 +0000 (12:06 -0800)]
selftests/bpf: Work-around EBUSY errors from hashmap update/delete
20b6cc34ea74 ("bpf: Avoid hashtab deadlock with map_locked") introduced
a possibility of getting EBUSY error on lock contention, which seems to happen
very deterministically in test_maps when running 1024 threads on low-CPU
machine. In libbpf CI case, it's a 2 CPU VM and it's hitting this 100% of the
time. Work around by retrying on EBUSY (and EAGAIN, while we are at it) after
a small sleep. sched_yield() is too agressive and fails even after 20 retries,
so I went with usleep(1) for backoff.
Also log actual error returned to make it easier to see what's going on.
Fixes:
20b6cc34ea74 ("bpf: Avoid hashtab deadlock with map_locked")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201223200652.3417075-1-andrii@kernel.org
Mario Limonciello [Mon, 14 Dec 2020 19:29:35 +0000 (13:29 -0600)]
e1000e: Export S0ix flags to ethtool
This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.
If you need this flag to be persisted across reboots, it's suggested
to use a udev rule to call adjust it until the kernel could have your
configuration in a disallow list.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mario Limonciello [Mon, 14 Dec 2020 19:29:34 +0000 (13:29 -0600)]
Revert "e1000e: disable s0ix entry and exit flows for ME systems"
commit
e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME
systems") disabled s0ix flows for systems that have various incarnations of
the i219-LM ethernet controller. This changed caused power consumption
regressions on the following shipping Dell Comet Lake based laptops:
* Latitude 5310
* Latitude 5410
* Latitude 5410
* Latitude 5510
* Precision 3550
* Latitude 5411
* Latitude 5511
* Precision 3551
* Precision 7550
* Precision 7750
This commit was introduced because of some regressions on certain Thinkpad
laptops. This comment was potentially caused by an earlier
commit
632fbd5eb5b0e ("e1000e: fix S0ix flows for cable connected case").
or it was possibly caused by a system not meeting platform architectural
requirements for low power consumption. Other changes made in the driver
with extended timeouts are expected to make the driver more impervious to
platform firmware behavior.
Fixes:
e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME systems")
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mario Limonciello [Mon, 14 Dec 2020 19:29:33 +0000 (13:29 -0600)]
e1000e: bump up timeout to wait when ME un-configures ULP mode
Per guidance from Intel ethernet architecture team, it may take
up to 1 second for unconfiguring ULP mode.
However in practice this seems to be taking up to 2 seconds on
some Lenovo machines. Detect scenarios that take more than 1 second
but less than 2.5 seconds and emit a warning on resume for those
scenarios.
Suggested-by: Aaron Ma <aaron.ma@canonical.com>
Suggested-by: Sasha Netfin <sasha.neftin@intel.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
CC: Mark Pearson <markpearson@lenovo.com>
Fixes:
f15bb6dde738cc8fa0 ("e1000e: Add support for S0ix")
BugLink: https://bugs.launchpad.net/bugs/1865570
Link: https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20200323191639.48826-1-aaron.ma@canonical.com/
Link: https://lkml.org/lkml/2020/12/13/15
Link: https://lkml.org/lkml/2020/12/14/708
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mario Limonciello [Mon, 14 Dec 2020 19:29:32 +0000 (13:29 -0600)]
e1000e: Only run S0ix flows if shutdown succeeded
If the shutdown failed, the part will be thawed and running
S0ix flows will put it into an undefined state.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Lijun Pan [Wed, 23 Dec 2020 20:49:04 +0000 (14:49 -0600)]
ibmvnic: continue fatal error reset after passive init
Commit
f9c6cea0b385 ("ibmvnic: Skip fatal error reset after passive init")
says "If the passive
CRQ initialization occurs before the FATAL reset task is processed,
the FATAL error reset task would try to access a CRQ message queue
that was freed, causing an oops. The problem may be most likely to
occur during DLPAR add vNIC with a non-default MTU, because the DLPAR
process will automatically issue a change MTU request.
Fix this by not processing fatal error reset if CRQ is passively
initialized after client-driven CRQ initialization fails."
The original commit skips a specific reset condition, but that does
not fix the problem it claims to fix, and misses a reset condition.
The effective fix is commit
0e435befaea4 ("ibmvnic: fix NULL pointer
dereference in ibmvic_reset_crq") and commit
a0faaa27c716 ("ibmvnic:
fix NULL pointer dereference in reset_sub_crq_queues"). With above
two fixes, there are no more crashes seen as described even without
the original commit, so I would like to revert the original commit.
Fixes:
f9c6cea0b385 ("ibmvnic: Skip fatal error reset after passive init")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201223204904.12677-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dinghao Liu [Wed, 23 Dec 2020 11:06:12 +0000 (19:06 +0800)]
net: ethernet: Fix memleak in ethoc_probe
When mdiobus_register() fails, priv->mdio allocated
by mdiobus_alloc() has not been freed, which leads
to memleak.
Fixes:
e7f4dc3536a4 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201223110615.31389-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
John Wang [Wed, 23 Dec 2020 05:55:23 +0000 (13:55 +0800)]
net/ncsi: Use real net-device for response handler
When aggregating ncsi interfaces and dedicated interfaces to bond
interfaces, the ncsi response handler will use the wrong net device to
find ncsi_dev, so that the ncsi interface will not work properly.
Here, we use the original net device to fix it.
Fixes:
138635cc27c9 ("net/ncsi: NCSI response packet handler")
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Link: https://lore.kernel.org/r/20201223055523.2069-1-wangzhiqiang.bj@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata [Tue, 22 Dec 2020 21:49:44 +0000 (22:49 +0100)]
net: dcb: Validate netlink message in DCB handler
DCB uses the same handler function for both RTM_GETDCB and RTM_SETDCB
messages. dcb_doit() bounces RTM_SETDCB mesasges if the user does not have
the CAP_NET_ADMIN capability.
However, the operation to be performed is not decided from the DCB message
type, but from the DCB command. Thus DCB_CMD_*_GET commands are used for
reading DCB objects, the corresponding SET and DEL commands are used for
manipulation.
The assumption is that set-like commands will be sent via an RTM_SETDCB
message, and get-like ones via RTM_GETDCB. However, this assumption is not
enforced.
It is therefore possible to manipulate DCB objects without CAP_NET_ADMIN
capability by sending the corresponding command in an RTM_GETDCB message.
That is a bug. Fix it by validating the type of the request message against
the type used for the response.
Fixes:
2f90b8657ec9 ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver")
Signed-off-by: Petr Machata <me@pmachata.org>
Link: https://lore.kernel.org/r/a2a9b88418f3a58ef211b718f2970128ef9e3793.1608673640.git.me@pmachata.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 23 Dec 2020 20:17:50 +0000 (12:17 -0800)]
Merge branch 'net-ipa-gsi-interrupt-handling-fixes'
Alex Elder says:
====================
net: ipa: GSI interrupt handling fixes
This series implements fixes for some issues related to handling
interrupts when GSI channel and event ring commands complete.
The first issue is that the completion condition for an event ring
or channel command could occur while the associated interrupt is
disabled. This would cause the interrupt to fire when it is
subsequently enabled, even if the condition it signals had already
been handled. The fix is to clear any pending interrupt conditions
before re-enabling the interrupt.
The second and third patches change how the success of an event ring
or channel command is determined. These commands change the state
of an event ring or channel. Previously the receipt of a completion
interrupt was required to consider a command successful. Instead, a
command is successful if it changes the state of the target event
ring or channel in the way expected. This way the command can
succeed even if the completion interrupt did not arrive while it was
enabled.
====================
Link: https://lore.kernel.org/r/20201222180012.22489-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 22 Dec 2020 18:00:12 +0000 (12:00 -0600)]
net: ipa: use state to determine event ring command success
This patch implements the same basic fix for event rings as the
previous one does for channels.
The result of issuing an event ring control command should be that
the event ring changes state. If enabled, a completion interrupt
signals that the event ring state has changed. This interrupt is
enabled by gsi_evt_ring_command() and disabled again after the
command has completed (or we time out).
There is a window of time during which the command could complete
successfully without interrupting. This would cause the event ring
to transition to the desired new state.
So whether a event ring command ends via completion interrupt or
timeout, we can consider the command successful if the event ring
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes:
b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 22 Dec 2020 18:00:11 +0000 (12:00 -0600)]
net: ipa: use state to determine channel command success
The result of issuing a channel control command should be that the
channel changes state. If enabled, a completion interrupt signals
that the channel state has changed. This interrupt is enabled by
gsi_channel_command() and disabled again after the command has
completed (or we time out).
There is a window of time--after the completion interrupt is disabled
but before the channel state is read--during which the command could
complete successfully without interrupting. This would cause the
channel to transition to the desired new state.
So whether a channel command ends via completion interrupt or
timeout, we can consider the command successful if the channel
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes:
d6c9e3f506ae8 ("net: ipa: only enable generic command completion IRQ when needed");
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 22 Dec 2020 18:00:10 +0000 (12:00 -0600)]
net: ipa: clear pending interrupts before enabling
We enable the completion interrupt for channel or event ring
commands only when we issue them. The interrupt is disabled after
the interrupt has fired, or after we have timed out waiting for it.
If we time out, the command could complete after the interrupt has
been disabled, causing a state change in the channel or event ring.
The interrupt associated with that state change would be delivered
the next time the completion interrupt is enabled.
To avoid previous command completions interfering with new commands,
clear all pending completion interrupts before re-enabling them for
a new command.
Fixes:
b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Noor Azura Ahmad Tarmizi [Tue, 22 Dec 2020 16:03:37 +0000 (00:03 +0800)]
stmmac: intel: Add PCI IDs for TGL-H platform
Add TGL-H PCI info and PCI IDs for the new TSN Controller to the list
of supported devices.
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Link: https://lore.kernel.org/r/20201222160337.30870-1-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Tue, 22 Dec 2020 15:16:13 +0000 (09:16 -0600)]
net: ipa: fix interconnect enable bug
When the core clock rate and interconnect bandwidth specifications
were moved into configuration data, a copy/paste bug was introduced,
causing the memory interconnect bandwidth to be set three times
rather than enabling the three different interconnects.
Fix this bug.
Fixes:
91d02f9551501 ("net: ipa: use config data for clocking")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201222151613.5730-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jeff Dike [Wed, 23 Dec 2020 02:54:21 +0000 (21:54 -0500)]
virtio_net: Fix recursive call to cpus_read_lock()
virtnet_set_channels can recursively call cpus_read_lock if CONFIG_XPS
and CONFIG_HOTPLUG are enabled.
The path is:
virtnet_set_channels - calls get_online_cpus(), which is a trivial
wrapper around cpus_read_lock()
netif_set_real_num_tx_queues
netif_reset_xps_queues_gt
netif_reset_xps_queues - calls cpus_read_lock()
This call chain and potential deadlock happens when the number of TX
queues is reduced.
This commit the removes netif_set_real_num_[tr]x_queues calls from
inside the get/put_online_cpus section, as they don't require that it
be held.
Fixes:
47be24796c13 ("virtio-net: fix the set affinity bug when CPU IDs are not consecutive")
Signed-off-by: Jeff Dike <jdike@akamai.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20201223025421.671-1-jdike@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 23 Dec 2020 03:43:32 +0000 (19:43 -0800)]
Merge tag 'wireless-drivers-2020-12-22' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
First set of fixes for v5.11, more fixes than usual this time. For
ath11k we have several fixes for QCA6390 PCI support and mt76 has
several. Also one build fix for mt76.
mt76
* fix two NULL pointer dereference
* fix build error when CONFIG_MAC80211_MESH is disabled
rtlwifi
* fix use-after-free in firmware handling code
ath11k
* error handling fixes
* fix crash found during connect and disconnect test
* handle HT disable better
* avoid printing qmi memory failure during firmware bootup
* disable ASPM during firmware bootup
* tag 'wireless-drivers-2020-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
MAINTAINERS: switch to different email address
mt76: mt7915: fix MESH ifdef block
mt76: mt76s: fix NULL pointer dereference in mt76s_process_tx_queue
mt76: sdio: remove wake logic in mt76s_process_tx_queue
mt76: usb: remove wake logic in mt76u_status_worker
ath11k: pci: disable ASPM L0sLs before downloading firmware
ath11k: qmi: try to allocate a big block of DMA memory first
rtlwifi: rise completion at the last step of firmware callback
mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker
ath11k: Fix ath11k_pci_fix_l1ss()
ath11k: Fix error code in ath11k_core_suspend()
ath11k: start vdev if a bss peer is already created
ath11k: fix crash caused by NULL rx_channel
ath11k: add missing null check on allocated skb
====================
Link: https://lore.kernel.org/r/20201222163727.D4336C433C6@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Manish Chopra [Mon, 21 Dec 2020 14:55:30 +0000 (06:55 -0800)]
qede: fix offload for IPIP tunnel packets
IPIP tunnels packets are unknown to device,
hence these packets are incorrectly parsed and
caused the packet corruption, so disable offlods
for such packets at run time.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20201221145530.7771-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Baruch Siach [Sun, 20 Dec 2020 08:49:47 +0000 (10:49 +0200)]
docs: netdev-FAQ: fix question headers formatting
Join adjacent questions to a single question line. This fixes the
formatting of questions that were not part of the heading.
Also, drop Q: and A: prefixes. We don't need them now that questions and
answers are visually separated.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/f76078ba5547744f2ec178984c32fbc7dcd29a2b.1608454187.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dinghao Liu [Sun, 20 Dec 2020 08:29:30 +0000 (16:29 +0800)]
net: ethernet: mvneta: Fix error handling in mvneta_probe
When mvneta_port_power_up() fails, we should execute
cleanup functions after label err_netdev to avoid memleak.
Fixes:
41c2b6b4f0f80 ("net: ethernet: mvneta: Add back interface mode validation")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20201220082930.21623-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lijun Pan [Sat, 19 Dec 2020 21:39:19 +0000 (15:39 -0600)]
ibmvnic: fix login buffer memory leak
Commit
34f0f4e3f488 ("ibmvnic: Fix login buffer memory leaks") frees
login_rsp_buffer in release_resources() and send_login()
because handle_login_rsp() does not free it.
Commit
f3ae59c0c015 ("ibmvnic: store RX and TX subCRQ handle array in
ibmvnic_adapter struct") frees login_rsp_buffer in handle_login_rsp().
It seems unnecessary to free it in release_resources() and send_login().
There are chances that handle_login_rsp returns earlier without freeing
buffers. Double-checking the buffer is harmless since
release_login_buffer and release_login_rsp_buffer will
do nothing if buffer is already freed.
Fixes:
f3ae59c0c015 ("ibmvnic: store RX and TX subCRQ handle array in ibmvnic_adapter struct")
Fixes:
34f0f4e3f488 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201219213919.21045-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 19 Dec 2020 18:55:38 +0000 (10:55 -0800)]
MAINTAINERS: remove names from mailing list maintainers
When searching for inactive maintainers it's useful to filter
out mailing list addresses. Such "maintainers" will obviously
never feature in a "From:" line of an email or a review tag.
Since "L:" entries only provide the address of a mailing list
without a fancy name extend this pattern to "M:" entries.
Alternatively we could reserve M: entries for humans only
and move the fake "maintainers" to L:. While I'd personally
prefer to reserve M: for humans only, I'm not 100% that's
a great choice either, given most L: entries are in fact
open mailing lists with public archives.
Link: https://lore.kernel.org/r/20201219185538.750076-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin Blumenstingl [Sat, 19 Dec 2020 13:50:36 +0000 (14:50 +0100)]
net: stmmac: dwmac-meson8b: ignore the second clock input
The dwmac glue registers on Amlogic Meson8b and newer SoCs has two clock
inputs:
- Meson8b and Meson8m2: MPLL2 and MPLL2 (the same parent is wired to
both inputs)
- GXBB, GXL, GXM, AXG, G12A, G12B, SM1: FCLK_DIV2 and MPLL2
All known vendor kernels and u-boots are using the first input only. We
let the common clock framework automatically choose the "right" parent.
For some boards this causes a problem though, specificially with G12A and
newer SoCs. The clock input is used for generating the 125MHz RGMII TX
clock. For the two input clocks this means on G12A:
- FCLK_DIV2: 999999985Hz / 8 =
124999998.125Hz
- MPLL2: 499999993Hz / 4 =
124999998.25Hz
In theory MPLL2 is the "better" clock input because it's gets us 0.125Hz
closer to the requested frequency than FCLK_DIV2. In reality however
there is a resource conflict because MPLL2 is needed to generate some of
the audio clocks. dwmac-meson8b probes first and sets up the clock tree
with MPLL2. This works fine until the audio driver comes and "steals"
the MPLL2 clocks and configures it with it's own rate (294909637Hz). The
common clock framework happily changes the MPLL2 rate but does not
reconfigure our RGMII TX clock tree, which then ends up at 73727409Hz,
which is more than 40% off the requested 125MHz.
Don't use the second clock input for now to force the common clock
framework to always select the first parent. This mimics the behavior
from the vendor driver and fixes the clock resource conflict with the
audio driver on G12A boards. Once the common clock framework can handle
this situation this change can be reverted again.
Fixes:
566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20201219135036.3216017-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Chulski [Sun, 20 Dec 2020 11:02:29 +0000 (13:02 +0200)]
net: mvpp2: Fix GoP port 3 Networking Complex Control configurations
During GoP port 2 Networking Complex Control mode of operation configurations,
also GoP port 3 mode of operation was wrongly set.
Patch removes these configurations.
Fixes:
f84bf386f395 ("net: mvpp2: initialize the GoP")
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608462149-1702-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Sat, 19 Dec 2020 12:19:24 +0000 (13:19 +0100)]
ppp: Fix PPPIOCUNBRIDGECHAN request number
PPPIOCGL2TPSTATS already uses 54. This shouldn't be a problem in
practice, but let's keep the logical decreasing assignment scheme.
Fixes:
4cf476ced45d ("ppp: add PPPIOCBRIDGECHAN and PPPIOCUNBRIDGECHAN ioctls")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/e3a4c355e3820331d8e1fffef8522739aae58b57.1608380117.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Sat, 19 Dec 2020 11:01:44 +0000 (14:01 +0300)]
atm: idt77252: call pci_disable_device() on error path
This error path needs to disable the pci device before returning.
Fixes:
ede58ef28e10 ("atm: remove deprecated use of pci api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X93dmC4NX0vbTpGp@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shannon Nelson [Fri, 18 Dec 2020 21:50:01 +0000 (13:50 -0800)]
ionic: account for vlan tag len in rx buffer len
Let the FW know we have enough receive buffer space for the
vlan tag if it isn't stripped.
Fixes:
0f3154e6bcb3 ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20201218215001.64696-1-snelson@pensando.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 22 Dec 2020 01:29:51 +0000 (17:29 -0800)]
Merge branch 'ucc_geth-fixes'
Rasmus Villemoes says:
====================
ucc_geth fixes
This is three bug fixes that fell out of a series of cleanups of the
ucc_geth driver.
====================
Link: https://lore.kernel.org/r/20201218105538.30563-1-rasmus.villemoes@prevas.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rasmus Villemoes [Fri, 18 Dec 2020 10:55:38 +0000 (11:55 +0100)]
ethernet: ucc_geth: fix use-after-free in ucc_geth_remove()
ugeth is the netdiv_priv() part of the netdevice. Accessing the memory
pointed to by ugeth (such as done by ucc_geth_memclean() and the two
of_node_puts) after free_netdev() is thus use-after-free.
Fixes:
80a9fad8e89a ("ucc_geth: fix module removal")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rasmus Villemoes [Fri, 18 Dec 2020 10:55:37 +0000 (11:55 +0100)]
ethernet: ucc_geth: fix definition and size of ucc_geth_tx_global_pram
Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rasmus Villemoes [Fri, 18 Dec 2020 10:55:36 +0000 (11:55 +0100)]
ethernet: ucc_geth: set dev->max_mtu to 1518
All the buffers and registers are already set up appropriately for an
MTU slightly above 1500, so we just need to expose this to the
networking stack. AFAICT, there's no need to implement .ndo_change_mtu
when the receive buffers are always set up to support the max_mtu.
This fixes several warnings during boot on our mpc8309-board with an
embedded mv88e6250 switch:
mv88e6085 mdio@
e0102120:10: nonfatal error -34 setting MTU 1500 on port 0
...
mv88e6085 mdio@
e0102120:10: nonfatal error -34 setting MTU 1500 on port 4
ucc_geth
e0102000.ethernet eth1: error -22 setting MTU to 1504 to include DSA overhead
The last line explains what the DSA stack tries to do: achieving an MTU
of 1500 on-the-wire requires that the master netdevice connected to
the CPU port supports an MTU of 1500+the tagging overhead.
Fixes:
bfcb813203e6 ("net: dsa: configure the MTU for switch ports")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli [Fri, 18 Dec 2020 17:38:43 +0000 (09:38 -0800)]
net: systemport: set dev->max_mtu to UMAC_MAX_MTU_SIZE
The driver is already allocating receive buffers of 2KiB and the
Ethernet MAC is configured to accept frames up to UMAC_MAX_MTU_SIZE.
Fixes:
bfcb813203e6 ("net: dsa: configure the MTU for switch ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20201218173843.141046-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 21 Dec 2020 19:25:06 +0000 (11:25 -0800)]
bpf: Add schedule point in htab_init_buckets()
We noticed that with a LOCKDEP enabled kernel,
allocating a hash table with 65536 buckets would
use more than 60ms.
htab_init_buckets() runs from process context,
it is safe to schedule to avoid latency spikes.
Fixes:
c50eb518e262 ("bpf: Use separate lockdep class for each hashtab")
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201221192506.707584-1-eric.dumazet@gmail.com
Arend van Spriel [Sun, 20 Dec 2020 14:18:07 +0000 (15:18 +0100)]
MAINTAINERS: switch to different email address
Switching to private mail account as work email is polluted with a legal
disclaimer. Just making it extra clear by changing the email address in
the MAINTAINERS file as well.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201220141807.17278-1-aspriel@gmail.com
Randy Dunlap [Fri, 18 Dec 2020 17:32:02 +0000 (09:32 -0800)]
mt76: mt7915: fix MESH ifdef block
Fix a build error when CONFIG_MAC80211_MESH is not enabled:
../drivers/net/wireless/mediatek/mt76/mt7915/init.c:47:2: error: expected expression before '}' token
}, {
^
Fixes:
af901eb4ab80 ("mt76: mt7915: get rid of dbdc debugfs knob")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Shayne Chen <shayne.chen@mediatek.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: linux-wireless@vger.kernel.org
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201218173202.23159-1-rdunlap@infradead.org
Lorenzo Bianconi [Tue, 8 Dec 2020 09:18:11 +0000 (10:18 +0100)]
mt76: mt76s: fix NULL pointer dereference in mt76s_process_tx_queue
Fix a possible NULL pointer dereference in mt76s_process_tx_queue that
can occur if status thread runs before allocating tx queues
Fixes:
6a618acb7e62 ("mt76: sdio: convert {status/net}_work to mt76_worker")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/b49c1b4edacd87b2241a9fd0431dd4864c8963f6.1607418933.git.lorenzo@kernel.org
Lorenzo Bianconi [Sat, 5 Dec 2020 10:35:26 +0000 (11:35 +0100)]
mt76: sdio: remove wake logic in mt76s_process_tx_queue
Similar to mmio/usb code path, remove wake logic in mt76s_process_tx_queue
routine. Starting from commit
90d494c99a99 ("mt76: improve tx queue
stop/wake"), the wake queue logic on the sdio status path is no longer
necessary since the hw queues are no longer stopped on the mt76 tx path.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/d2d7d9d437f4dec2ef1df0ed070b9cf299f021ad.1607164041.git.lorenzo@kernel.org
Lorenzo Bianconi [Sat, 5 Dec 2020 10:35:25 +0000 (11:35 +0100)]
mt76: usb: remove wake logic in mt76u_status_worker
Similar to mmio code path, remove wake logic in mt76u_status_worker handler.
Starting from commit
90d494c99a99 ("mt76: improve tx queue stop/wake")', the
wake queue logic on the usb status path is no longer necessary since the hw
queues are no longer stopped on the mt76 tx path.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/00009bf0cfdc9565e4432cad3ed51888c667c25d.1607164041.git.lorenzo@kernel.org
Kalle Valo [Sun, 20 Dec 2020 11:57:17 +0000 (13:57 +0200)]
Merge ath-current from git://git./linux/kernel/git/kvalo/ath.git
ath.git fixes for 5.11. Major changes:
ath11k
* add null check for skb allocation
* fix crash found during connect/disconnect stress testing
* fix for HT disabled case
* brown paperbag fixes for my bugs in suspend code
* fix an unnecessary qmi allocation during firmware bootup
* disable ASPM during firmware bootup to avoid issues
Stefan Chulski [Thu, 17 Dec 2020 18:37:46 +0000 (20:37 +0200)]
net: mvpp2: prs: fix PPPoE with ipv6 packet parse
Current PPPoE+IPv6 entry is jumping to 'next-hdr'
field and not to 'DIP' field as done for IPv4.
Fixes:
3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Reported-by: Liron Himi <lironh@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608230266-22111-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Chulski [Thu, 17 Dec 2020 18:30:17 +0000 (20:30 +0200)]
net: mvpp2: Add TCAM entry to drop flow control pause frames
Issue:
Flow control frame used to pause GoP(MAC) was delivered to the CPU
and created a load on the CPU. Since XOFF/XON frames are used only
by MAC, these frames should be dropped inside MAC.
Fix:
According to 802.3-2012 - IEEE Standard for Ethernet pause frame
has unique destination MAC address 01-80-C2-00-00-01.
Add TCAM parser entry to track and drop pause frames by destination MAC.
Fixes:
3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608229817-21951-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Chulski [Thu, 17 Dec 2020 14:52:15 +0000 (16:52 +0200)]
net: mvpp2: disable force link UP during port init procedure
Force link UP can be enabled by bootloader during tftpboot
and breaks NFS support.
Force link UP disabled during port init procedure.
Fixes:
f84bf386f395 ("net: mvpp2: initialize the GoP")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/1608216735-14501-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 19 Dec 2020 02:07:13 +0000 (18:07 -0800)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Incorrect loop in error path of nft_set_elem_expr_clone(),
from Colin Ian King.
2) Missing xt_table_get_private_protected() to access table
private data in x_tables, from Subash Abhinov Kasiviswanathan.
3) Possible oops in ipset hash type resize, from Vasily Averin.
4) Fix shift-out-of-bounds in ipset hash type, also from Vasily.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: ipset: fix shift-out-of-bounds in htable_bits()
netfilter: ipset: fixes possible oops in mtype_resize
netfilter: x_tables: Update remaining dereference to RCU
netfilter: nftables: fix incorrect increment of loop counter
====================
Link: https://lore.kernel.org/r/20201218120409.3659-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Davide Caratti [Thu, 17 Dec 2020 21:29:46 +0000 (22:29 +0100)]
net/sched: sch_taprio: ensure to reset/destroy all child qdiscs
taprio_graft() can insert a NULL element in the array of child qdiscs. As
a consquence, taprio_reset() might not reset child qdiscs completely, and
taprio_destroy() might leak resources. Fix it by ensuring that loops that
iterate over q->qdiscs[] don't end when they find the first NULL item.
Fixes:
44d4775ca518 ("net/sched: sch_taprio: reset child qdiscs before freeing them")
Fixes:
5a781ccbd19e ("tc: Add support for configuring the taprio scheduler")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/13edef6778fef03adc751582562fba4a13e06d6a.1608240532.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 19 Dec 2020 00:39:55 +0000 (16:39 -0800)]
Merge branch '40GbE' of git://git./linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-12-17
Sylwester fixes an issue where PF was not properly being rebuilt
following VF removal for i40e.
Jakub Kicinski fixes a double release of rtnl_lock on
iavf_lan_add_device() error for iavf.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: fix double-release of rtnl_lock
i40e: Fix Error I40E_AQ_RC_EINVAL when removing VFs
====================
Link: https://lore.kernel.org/r/20201217223418.3134992-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Baruch Siach [Wed, 16 Dec 2020 07:28:04 +0000 (09:28 +0200)]
net: af_packet: fix procfs header for 64-bit pointers
On 64-bit systems the packet procfs header field names following 'sk'
are not aligned correctly:
sk RefCnt Type Proto Iface R Rmem User Inode
00000000605d2c64 3 3 0003 7 1 450880 0 16643
00000000080e9b80 2 2 0000 0 0 0 0 17404
00000000b23b8a00 2 2 0000 0 0 0 0 17421
...
With this change field names are correctly aligned:
sk RefCnt Type Proto Iface R Rmem User Inode
000000005c3b1d97 3 3 0003 7 1 21568 0 16178
000000007be55bb7 3 3 fbce 8 1 0 0 16250
00000000be62127d 3 3 fbcd 8 1 0 0 16254
...
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/54917251d8433735d9a24e935a6cb8eb88b4058a.1608103684.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tian Tao [Wed, 16 Dec 2020 02:47:15 +0000 (10:47 +0800)]
bpf: Remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/1608086835-54523-1-git-send-email-tiantao6@hisilicon.com
Colin Ian King [Mon, 14 Dec 2020 22:35:39 +0000 (22:35 +0000)]
selftests/bpf: Fix spelling mistake "tranmission" -> "transmission"
There are two spelling mistakes in output messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20201214223539.83168-1-colin.king@canonical.com
Magnus Karlsson [Fri, 18 Dec 2020 13:45:25 +0000 (14:45 +0100)]
xsk: Rollback reservation at NETDEV_TX_BUSY
Rollback the reservation in the completion ring when we get a
NETDEV_TX_BUSY. When this error is received from the driver, we are
supposed to let the user application retry the transmit again. And in
order to do this, we need to roll back the failed send so it can be
retried. Unfortunately, we did not cancel the reservation we had made
in the completion ring. By not doing this, we actually make the
completion ring one entry smaller per NETDEV_TX_BUSY error we get, and
after enough of these errors the completion ring will be of size zero
and transmit will stop working.
Fix this by cancelling the reservation when we get a NETDEV_TX_BUSY
error.
Fixes:
642e450b6b59 ("xsk: Do not discard packet when NETDEV_TX_BUSY")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20201218134525.13119-3-magnus.karlsson@gmail.com
Magnus Karlsson [Fri, 18 Dec 2020 13:45:24 +0000 (14:45 +0100)]
xsk: Fix race in SKB mode transmit with shared cq
Fix a race when multiple sockets are simultaneously calling sendto()
when the completion ring is shared in the SKB case. This is the case
when you share the same netdev and queue id through the
XDP_SHARED_UMEM bind flag. The problem is that multiple processes can
be in xsk_generic_xmit() and call the backpressure mechanism in
xskq_prod_reserve(xs->pool->cq). As this is a shared resource in this
specific scenario, a race might occur since the rings are
single-producer single-consumer.
Fix this by moving the tx_completion_lock from the socket to the pool
as the pool is shared between the sockets that share the completion
ring. (The pool is not shared when this is not the case.) And then
protect the accesses to xskq_prod_reserve() with this lock. The
tx_completion_lock is renamed cq_lock to better reflect that it
protects accesses to the potentially shared completion ring.
Fixes:
35fcde7f8deb ("xsk: support for Tx")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20201218134525.13119-2-magnus.karlsson@gmail.com
Carl Huang [Thu, 17 Dec 2020 15:22:10 +0000 (17:22 +0200)]
ath11k: pci: disable ASPM L0sLs before downloading firmware
Sometimes QCA6390 doesn't switch to amss state as device enters
L1ss state, so disable L0sL1s during firmware downloading.
Driver recovers the ASPM to default value in start callback
or powerdown callback.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608218530-15426-1-git-send-email-kvalo@codeaurora.org
Carl Huang [Thu, 17 Dec 2020 07:04:57 +0000 (09:04 +0200)]
ath11k: qmi: try to allocate a big block of DMA memory first
Not all firmware versions support allocating DMA memory in smaller blocks so
first try to allocate big block of DMA memory for QMI. If the allocation fails,
let firmware request multiple blocks of DMA memory with smaller size.
This also fixes an unnecessary error message seen during ath11k probe on
QCA6390:
ath11k_pci 0000:06:00.0: Respond mem req failed, result: 1, err: 0
ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-22
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608127593-15192-1-git-send-email-kvalo@codeaurora.org
Jakub Kicinski [Thu, 3 Dec 2020 02:18:06 +0000 (18:18 -0800)]
iavf: fix double-release of rtnl_lock
This code does not jump to exit on an error in iavf_lan_add_device(),
so the rtnl_unlock() from the normal path will follow.
Fixes:
b66c7bc1cd4d ("iavf: Refactor init state machine")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Magnus Karlsson [Mon, 14 Dec 2020 08:51:27 +0000 (09:51 +0100)]
xsk: Fix memory leak for failed bind
Fix a possible memory leak when a bind of an AF_XDP socket fails. When
the fill and completion rings are created, they are tied to the
socket. But when the buffer pool is later created at bind time, the
ownership of these two rings are transferred to the buffer pool as
they might be shared between sockets (and the buffer pool cannot be
created until we know what we are binding to). So, before the buffer
pool is created, these two rings are cleaned up with the socket, and
after they have been transferred they are cleaned up together with
the buffer pool.
The problem is that ownership was transferred before it was absolutely
certain that the buffer pool could be created and initialized
correctly and when one of these errors occurred, the fill and
completion rings did neither belong to the socket nor the pool and
where therefore leaked. Solve this by moving the ownership transfer
to the point where the buffer pool has been completely set up and
there is no way it can fail.
Fixes:
7361f9c3d719 ("xsk: Move fill and completion rings to buffer pool")
Reported-by: syzbot+cfa88ddd0655afa88763@syzkaller.appspotmail.com
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20201214085127.3960-1-magnus.karlsson@gmail.com
Linus Torvalds [Thu, 17 Dec 2020 21:45:24 +0000 (13:45 -0800)]
Merge tag 'net-5.11-rc1' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - always broken:
- net/smc: fix access to parent of an ib device
- devlink: use _BITUL() macro instead of BIT() in the UAPI header
- handful of mptcp fixes
Previous release - regressions:
- intel: AF_XDP: clear the status bits for the next_to_use descriptor
- dpaa2-eth: fix the size of the mapped SGT buffer
Previous release - always broken:
- mptcp: fix security context on server socket
- ethtool: fix string set id check
- ethtool: fix error paths in ethnl_set_channels()
- lan743x: fix rx_napi_poll/interrupt ping-pong
- qca: ar9331: fix sleeping function called from invalid context bug"
* tag 'net-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (32 commits)
net/sched: sch_taprio: reset child qdiscs before freeing them
nfp: move indirect block cleanup to flower app stop callback
octeontx2-af: Fix undetected unmap PF error check
net: nixge: fix spelling mistake in Kconfig: "Instuments" -> "Instruments"
qlcnic: Fix error code in probe
mptcp: fix pending data accounting
mptcp: push pending frames when subflow has free space
mptcp: properly annotate nested lock
mptcp: fix security context on server socket
net/mlx5: Fix compilation warning for 32-bit platform
mptcp: clear use_ack and use_map when dropping other suboptions
devlink: use _BITUL() macro instead of BIT() in the UAPI header
net: korina: fix return value
net/smc: fix access to parent of an ib device
ethtool: fix error paths in ethnl_set_channels()
nfc: s3fwrn5: Remove unused NCI prop commands
nfc: s3fwrn5: Remove the delay for NFC sleep
phy: fix kdoc warning
tipc: do sanity check payload of a netlink message
use __netdev_notify_peers in hyperv
...
Linus Torvalds [Thu, 17 Dec 2020 21:41:27 +0000 (13:41 -0800)]
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
- New drivers and OpenRISC support for the LiteX platform
- A bug fix to support userspace gdb debugging
- Fixes one compile issue with blk-iocost
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: add local64.h to fix blk-iocost build
openrisc: fix trap for debugger breakpoint signalling
openrisc: add support for LiteX
drivers/tty/serial: add LiteUART driver
dt-bindings: serial: document LiteUART bindings
drivers/soc/litex: add LiteX SoC Controller driver
dt-bindings: soc: document LiteX SoC Controller bindings
dt-bindings: vendor: add vendor prefix for LiteX
Linus Torvalds [Thu, 17 Dec 2020 21:34:25 +0000 (13:34 -0800)]
Merge tag 'powerpc-5.11-1' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the
hashed page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core
do not share an L2, allowing the scheduler to make better scheduling
decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various
parts of the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to: Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Ard Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King,
Daniel Axtens, David Hildenbrand, Frederic Barrat, Ganesh Goudar,
Gautham R. Shenoy, Geert Uytterhoeven, Giuseppe Sacco, Greg Kurz,
Harish, Jan Kratochvil, Jordan Niethe, Kaixu Xia, Laurent Dufour,
Leonardo Bras, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu
Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov, Oliver
O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej
Siewior , Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe
Kleine-König, Vincent Stehlé, Youling Tang, and Zhang Xiaoxu.
* tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (304 commits)
powerpc/32s: Fix cleanup_cpu_mmu_context() compile bug
powerpc: Add config fragment for disabling -Werror
powerpc/configs: Add ppc64le_allnoconfig target
powerpc/powernv: Rate limit opal-elog read failure message
powerpc/pseries/memhotplug: Quieten some DLPAR operations
powerpc/ps3: use dma_mapping_error()
powerpc: force inlining of csum_partial() to avoid multiple csum_partial() with GCC10
powerpc/perf: Fix Threshold Event Counter Multiplier width for P10
powerpc/mm: Fix hugetlb_free_pmd_range() and hugetlb_free_pud_range()
KVM: PPC: Book3S HV: Fix mask size for emulated msgsndp
KVM: PPC: fix comparison to bool warning
KVM: PPC: Book3S: Assign boolean values to a bool variable
powerpc: Inline setup_kup()
powerpc/64s: Mark the kuap/kuep functions non __init
KVM: PPC: Book3S HV: XIVE: Add a comment regarding VP numbering
powerpc/xive: Improve error reporting of OPAL calls
powerpc/xive: Simplify xive_do_source_eoi()
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_EOI_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_MASK_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_SHIFT_BUG
...
Linus Torvalds [Thu, 17 Dec 2020 21:22:17 +0000 (13:22 -0800)]
Merge tag 'trace-v5.11' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The major update to this release is that there's a new arch config
option called CONFIG_HAVE_DYNAMIC_FTRACE_WITH_ARGS.
Currently, only x86_64 enables it. All the ftrace callbacks now take a
struct ftrace_regs instead of a struct pt_regs. If the architecture
has HAVE_DYNAMIC_FTRACE_WITH_ARGS enabled, then the ftrace_regs will
have enough information to read the arguments of the function being
traced, as well as access to the stack pointer.
This way, if a user (like live kernel patching) only cares about the
arguments, then it can avoid using the heavier weight "regs" callback,
that puts in enough information in the struct ftrace_regs to simulate
a breakpoint exception (needed for kprobes).
A new config option that audits the timestamps of the ftrace ring
buffer at most every event recorded.
Ftrace recursion protection has been cleaned up to move the protection
to the callback itself (this saves on an extra function call for those
callbacks).
Perf now handles its own RCU protection and does not depend on ftrace
to do it for it (saving on that extra function call).
New debug option to add "recursed_functions" file to tracefs that
lists all the places that triggered the recursion protection of the
function tracer. This will show where things need to be fixed as
recursion slows down the function tracer.
The eval enum mapping updates done at boot up are now offloaded to a
work queue, as it caused a noticeable pause on slow embedded boards.
Various clean ups and last minute fixes"
* tag 'trace-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
tracing: Offload eval map updates to a work queue
Revert: "ring-buffer: Remove HAVE_64BIT_ALIGNED_ACCESS"
ring-buffer: Add rb_check_bpage in __rb_allocate_pages
ring-buffer: Fix two typos in comments
tracing: Drop unneeded assignment in ring_buffer_resize()
tracing: Disable ftrace selftests when any tracer is running
seq_buf: Avoid type mismatch for seq_buf_init
ring-buffer: Fix a typo in function description
ring-buffer: Remove obsolete rb_event_is_commit()
ring-buffer: Add test to validate the time stamp deltas
ftrace/documentation: Fix RST C code blocks
tracing: Clean up after filter logic rewriting
tracing: Remove the useless value assignment in test_create_synth_event()
livepatch: Use the default ftrace_ops instead of REGS when ARGS is available
ftrace/x86: Allow for arguments to be passed in to ftrace_regs by default
ftrace: Have the callbacks receive a struct ftrace_regs instead of pt_regs
MAINTAINERS: assign ./fs/tracefs to TRACING
tracing: Fix some typos in comments
ftrace: Remove unused varible 'ret'
ring-buffer: Add recording of ring buffer recursion into recursed_functions
...
Linus Torvalds [Thu, 17 Dec 2020 21:01:31 +0000 (13:01 -0800)]
Merge tag 'modules-for-v5.11' of git://git./linux/kernel/git/jeyu/linux
Pull modules updates from Jessica Yu:
"Summary of modules changes for the 5.11 merge window:
- Fix a race condition between systemd/udev and the module loader.
The module loader was sending a uevent before the module was fully
initialized (i.e., before its init function has been called). This
means udev can start processing the module uevent before the module
has finished initializing, and some udev rules expect that the
module has initialized already upon receiving the uevent.
This resulted in some systemd mount units failing if udev processes
the event faster than the module can finish init. This is fixed by
delaying the uevent until after the module has called its init
routine.
- Make the linker array sections for kernel params and module version
attributes more robust by switching to use the alignment of the
type in question.
Namely, linker section arrays will be constructed using the
alignment required by the struct (using __alignof__()) as opposed
to a specific value such as sizeof(void *) or sizeof(long). This is
less likely to cause breakages should the size of the type ever
change (Johan Hovold)
- Fix module state inconsistency by setting it back to GOING when a
module fails to load and is on its way out (Miroslav Benes)
- Some comment and code cleanups (Sergey Shtylyov)"
* tag 'modules-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: delay kobject uevent until after module init call
module: drop semicolon from version macro
init: use type alignment for kernel parameters
params: clean up module-param macros
params: use type alignment for kernel parameters
params: drop redundant "unused" attributes
module: simplify version-attribute handling
module: drop version-attribute alignment
module: fix comment style
module: add more 'kernel-doc' comments
module: fix up 'kernel-doc' comments
module: only handle errors with the *switch* statement in module_sig_check()
module: avoid *goto*s in module_sig_check()
module: merge repetitive strings in module_sig_check()
module: set MODULE_STATE_GOING state when a module fails to load
Sylwester Dziedziuch [Thu, 22 Oct 2020 10:39:36 +0000 (12:39 +0200)]
i40e: Fix Error I40E_AQ_RC_EINVAL when removing VFs
When removing VFs for PF added to bridge there was
an error I40E_AQ_RC_EINVAL. It was caused by not properly
resetting and reinitializing PF when adding/removing VFs.
Changed how reset is performed when adding/removing VFs
to properly reinitialize PFs VSI.
Fixes:
fc60861e9b00 ("i40e: start up in VEPA mode by default")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Linus Torvalds [Thu, 17 Dec 2020 20:52:23 +0000 (12:52 -0800)]
Merge tag 'dmaengine-5.11-rc1' of git://git./linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"The last dmaengine updates for this year :)
This contains couple of new drivers, new device support and updates to
bunch of drivers.
New drivers/devices:
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI drivers"
* tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (75 commits)
soc: ti: k3-ringacc: Use correct error casting in k3_ringacc_dmarings_init
dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA
dmaengine: ti: k3-udma: Initial support for K3 PKTDMA
dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling
dmaengine: ti: k3-udma: Initial support for K3 BCDMA
soc: ti: k3-ringacc: add AM64 DMA rings support.
dmaengine: ti: Add support for k3 event routers
dmaengine: ti: k3-psil: Add initial map for AM64
dmaengine: ti: k3-psil: Extend psil_endpoint_config for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 BCDMA
dmaengine: dmatest: Use dmaengine_get_dma_device
dmaengine: doc: client: Update for dmaengine_get_dma_device() usage
dmaengine: Add support for per channel coherency handling
dmaengine: of-dma: Add support for optional router configuration callback
dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings
dmaengine: ti: k3-udma-glue: Get the ringacc from udma_dev
dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API
dmaengine: ti: k3-udma: Add support for second resource range from sysfw
dmaengine: ti: k3-udma: Wait for peer teardown completion if supported
...
Linus Torvalds [Thu, 17 Dec 2020 20:39:39 +0000 (12:39 -0800)]
Merge tag 'mailbox-v5.11' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- arm: added mhu-v2 controller driver
- arm_mhu_db: fix kfree by using devm_ variant
- stm32-ipcc: misc cleanup
* tag 'mailbox-v5.11' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: arm_mhuv2: Add driver
dt-bindings: mailbox : arm,mhuv2: Add bindings
mailbox: stm32-ipcc: cast void pointers to unsigned long
mailbox: stm32-ipcc: remove duplicate error message
mailbox: stm32-ipcc: add COMPILE_TEST dependency
mailbox: arm_mhu_db: Fix mhu_db_shutdown by replacing kfree with devm_kfree
Linus Torvalds [Thu, 17 Dec 2020 20:15:03 +0000 (12:15 -0800)]
Merge tag 'nfs-for-5.11-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- NFSv3: Add emulation of lookupp() to improve open_by_filehandle()
support
- A series of patches to improve readdir performance, particularly
with large directories
- Basic support for using NFS/RDMA with the pNFS files and flexfiles
drivers
- Micro-optimisations for RDMA
- RDMA tracing improvements
Bugfixes:
- Fix a long standing bug with xs_read_xdr_buf() when receiving
partial pages (Dan Aloni)
- Various fixes for getxattr and listxattr, when used over non-TCP
transports
- Fixes for containerised NFS from Sargun Dhillon
- switch nfsiod to be an UNBOUND workqueue (Neil Brown)
- READDIR should not ask for security label information if there is
no LSM policy (Olga Kornievskaia)
- Avoid using interval-based rebinding with TCP in lockd (Calum
Mackay)
- A series of RPC and NFS layer fixes to support the NFSv4.2
READ_PLUS code
- A couple of fixes for pnfs/flexfiles read failover
Cleanups:
- Various cleanups for the SUNRPC xdr code in conjunction with the
READ_PLUS fixes"
* tag 'nfs-for-5.11-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (90 commits)
NFS/pNFS: Fix a typo in ff_layout_resend_pnfs_read()
pNFS/flexfiles: Avoid spurious layout returns in ff_layout_choose_ds_for_read
NFSv4/pnfs: Add tracing for the deviceid cache
fs/lockd: convert comma to semicolon
NFSv4.2: fix error return on memory allocation failure
NFSv4.2/pnfs: Don't use READ_PLUS with pNFS yet
NFSv4.2: Deal with potential READ_PLUS data extent buffer overflow
NFSv4.2: Don't error when exiting early on a READ_PLUS buffer overflow
NFSv4.2: Handle hole lengths that exceed the READ_PLUS read buffer
NFSv4.2: decode_read_plus_hole() needs to check the extent offset
NFSv4.2: decode_read_plus_data() must skip padding after data segment
NFSv4.2: Ensure we always reset the result->count in decode_read_plus()
SUNRPC: When expanding the buffer, we may need grow the sparse pages
SUNRPC: Cleanup - constify a number of xdr_buf helpers
SUNRPC: Clean up open coded setting of the xdr_stream 'nwords' field
SUNRPC: _copy_to/from_pages() now check for zero length
SUNRPC: Cleanup xdr_shrink_bufhead()
SUNRPC: Fix xdr_expand_hole()
SUNRPC: Fixes for xdr_align_data()
SUNRPC: _shift_data_left/right_pages should check the shift length
...