OSDN Git Service
Sasha Levin [Mon, 10 Dec 2018 23:52:35 +0000 (18:52 -0500)]
arm64: dts: rockchip: remove vdd_log from rock960 to fix a stability issues
[ Upstream commit
13682e524167cbd7e2a26c5e91bec765f0f96273 ]
When the performance governor is set as default, the rock960 hangs
around one minute after booting, whatever the activity is (idle, key
pressed, loaded, ...).
Based on the commit log found at https://patchwork.kernel.org/patch/
10092377/
"vdd_log has no consumer and therefore will not be set to a specific
voltage. Still the PWM output pin gets configured and thence the vdd_log
output voltage will changed from it's default. Depending on the idle
state of the PWM this will slightly over or undervoltage the logic supply
of the RK3399 and cause instability with GbE (undervoltage) and PCIe
(overvoltage). Since the default value set by a voltage divider is the
correct supply voltage and we don't need to change it during runtime we
remove the rail from the devicetree completely so the PWM pin will not
be configured."
After removing the vdd-log from the rock960's specific DT, the board
does no longer hang and shows a stable behavior.
Apply the same change for the rock960 by removing the vdd-log from the
DT.
Fixes:
874846f1fccd ("arm64: dts: rockchip: add 96boards RK3399 Ficus board")
Cc: stable@vger.kernel.org
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sl: adjust filename for 4.19]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mathias Nyman [Wed, 5 Dec 2018 12:22:39 +0000 (14:22 +0200)]
xhci: Prevent U1/U2 link pm states if exit latency is too long
commit
0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream.
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sandeep Singh [Wed, 5 Dec 2018 12:22:38 +0000 (14:22 +0200)]
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
commit
a7d57abcc8a5bdeb53bbf8e87558e8e0a2c2a29d upstream.
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook [Tue, 30 Oct 2018 21:12:56 +0000 (22:12 +0100)]
ARM: 8806/1: kprobes: Fix false positive with FORTIFY_SOURCE
commit
e46daee53bb50bde38805f1823a182979724c229 upstream.
The arm compiler internally interprets an inline assembly label
as an unsigned long value, not a pointer. As a result, under
CONFIG_FORTIFY_SOURCE, the address of a label has a size of 4 bytes,
which was tripping the runtime checks. Instead, we can just cast the label
(as done with the size calculations earlier).
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=
1639397
Reported-by: William Cohen <wcohen@redhat.com>
Fixes:
6974f0c4555e ("include/linux/string.h: add the option of fortified string.h functions")
Cc: stable@vger.kernel.org
Acked-by: Laura Abbott <labbott@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: William Cohen <wcohen@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Mon, 12 Nov 2018 15:43:22 +0000 (09:43 -0600)]
dmaengine: cppi41: delete channel from pending list when stop channel
commit
59861547ec9a9736e7882f6fb0c096a720ff811a upstream.
The driver defines three states for a cppi channel.
- idle: .chan_busy == 0 && not in .pending list
- pending: .chan_busy == 0 && in .pending list
- busy: .chan_busy == 1 && not in .pending list
There are cases in which the cppi channel could be in the pending state
when cppi41_dma_issue_pending() is called after cppi41_runtime_suspend()
is called.
cppi41_stop_chan() has a bug for these cases to set channels to idle state.
It only checks the .chan_busy flag, but not the .pending list, then later
when cppi41_runtime_resume() is called the channels in .pending list will
be transitioned to busy state.
Removing channels from the .pending list solves the problem.
Fixes:
975faaeb9985 ("dma: cppi41: start tear down only if channel is busy")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Bin Liu <b-liu@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:37 +0000 (03:40 +0000)]
dmaengine: imx-sdma: use GFP_NOWAIT for dma descriptor allocations
commit
64068853bc77786d1a28abb4087d6a3e93aedbe2 upstream.
DMA buffer descriptors aren't allocated from atomic context, so they
can use the less heavyweigth GFP_NOWAIT.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:33 +0000 (03:40 +0000)]
dmaengine: imx-sdma: implement channel termination via worker
commit
b8603d2a5795c42f78998e70dc792336e0dc20c9 upstream.
The dmaengine documentation states that device_terminate_all may be
asynchronous and need not wait for the active transfers to stop.
This allows us to move most of the functionality currently implemented
in the sdma channel termination function to run in a worker, outside
of any atomic context. Moving this out of atomic context has two
benefits: we can now sleep while waiting for the channel to terminate,
instead of busy waiting and the freeing of the dma descriptors happens
with IRQs enabled, getting rid of a warning in the dma mapping code.
As the termination is now async, we need to implement the
device_synchronize dma engine function which simply waits for the
worker to finish its execution.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:28 +0000 (03:40 +0000)]
Revert "dmaengine: imx-sdma: alloclate bd memory from dma pool"
commit
ebb853b1bd5f659b92c71dc6a9de44cfc37c78c0 upstream.
This reverts commit
fe5b85c656bc. The SDMA engine needs the descriptors to
be contiguous in memory. As the dma pool API is only able to provide a
single descriptor per alloc invocation there is no guarantee that multiple
descriptors satisfy this requirement. Also the code in question is broken
as it only allocates memory for a single descriptor, without looking at the
number of descriptors required for the transfer, leading to out-of-bounds
accesses when the descriptors are written.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:25 +0000 (03:40 +0000)]
Revert "dmaengine: imx-sdma: Use GFP_NOWAIT for dma allocations"
commit
c06abca69218ac42fa58d1ba7a7b0d9bab5f1b18 upstream.
This reverts commit
c1199875d327, as this depends on another commit
that is going to be reverted.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Wed, 5 Dec 2018 16:33:59 +0000 (18:33 +0200)]
dmaengine: dw: Fix FIFO size for Intel Merrifield
commit
ffe843b18211301ad25893eba09f402c19d12304 upstream.
Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.
Fix this by partitioning it as 64 bytes per channel.
Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.
Fixes:
199244d69458 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuck Lever [Fri, 30 Nov 2018 20:39:57 +0000 (15:39 -0500)]
SUNRPC: Fix leak of krb5p encode pages
commit
8dae5398ab1ac107b1517e8195ed043d5f422bd0 upstream.
call_encode can be invoked more than once per RPC call. Ensure that
each call to gss_wrap_req_priv does not overwrite pointers to
previously allocated memory.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Fri, 7 Dec 2018 12:47:10 +0000 (12:47 +0000)]
arm64: hibernate: Avoid sending cross-calling with interrupts disabled
commit
b4aecf78083d8c6424657c1746c7c3de6e61669f upstream.
Since commit
3b8c9f1cdfc50 ("arm64: IPI each CPU after invalidating the
I-cache for kernel mappings"), a call to flush_icache_range() will use
an IPI to cross-call other online CPUs so that any stale instructions
are flushed from their pipelines. This triggers a WARN during the
hibernation resume path, where flush_icache_range() is called with
interrupts disabled and is therefore prone to deadlock:
| Disabling non-boot CPUs ...
| CPU1: shutdown
| psci: CPU1 killed.
| CPU2: shutdown
| psci: CPU2 killed.
| CPU3: shutdown
| psci: CPU3 killed.
| WARNING: CPU: 0 PID: 1 at ../kernel/smp.c:416 smp_call_function_many+0xd4/0x350
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc4 #1
Since all secondary CPUs have been taken offline prior to invalidating
the I-cache, there's actually no need for an IPI and we can simply call
__flush_icache_range() instead.
Cc: <stable@vger.kernel.org>
Fixes:
3b8c9f1cdfc50 ("arm64: IPI each CPU after invalidating the I-cache for kernel mappings")
Reported-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Hajnoczi [Mon, 5 Nov 2018 10:35:47 +0000 (10:35 +0000)]
vhost/vsock: fix use-after-free in network stack callers
commit
834e772c8db0c6a275d75315d90aba4ebbb1e249 upstream.
If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible. This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.
Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu(). This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.
This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+bd391451452fb0b93039@syzkaller.appspotmail.com
Reported-by: syzbot+e3e074963495f92a89ed@syzkaller.appspotmail.com
Reported-by: syzbot+d5a0a170c5069658b141@syzkaller.appspotmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Halil Pasic [Wed, 26 Sep 2018 16:48:30 +0000 (18:48 +0200)]
virtio/s390: fix race in ccw_io_helper()
commit
78b1a52e05c9db11d293342e8d6d8a230a04b4e7 upstream.
While ccw_io_helper() seems like intended to be exclusive in a sense that
it is supposed to facilitate I/O for at most one thread at any given
time, there is actually nothing ensuring that threads won't pile up at
vcdev->wait_q. If they do, all threads get woken up and see the status
that belongs to some other request than their own. This can lead to bugs.
For an example see:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/
1788432
This race normally does not cause any problems. The operations provided
by struct virtio_config_ops are usually invoked in a well defined
sequence, normally don't fail, and are normally used quite infrequent
too.
Yet, if some of the these operations are directly triggered via sysfs
attributes, like in the case described by the referenced bug, userspace
is given an opportunity to force races by increasing the frequency of the
given operations.
Let us fix the problem by ensuring, that for each device, we finish
processing the previous request before starting with a new one.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Cc: stable@vger.kernel.org
Message-Id: <
20180925121309.58524-3-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Halil Pasic [Wed, 26 Sep 2018 16:48:29 +0000 (18:48 +0200)]
virtio/s390: avoid race on vcdev->config
commit
2448a299ec416a80f699940a86f4a6d9a4f643b1 upstream.
Currently we have a race on vcdev->config in virtio_ccw_get_config() and
in virtio_ccw_set_config().
This normally does not cause problems, as these are usually infrequent
operations. However, for some devices writing to/reading from the config
space can be triggered through sysfs attributes. For these, userspace can
force the race by increasing the frequency.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Cc: stable@vger.kernel.org
Message-Id: <
20180925121309.58524-2-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Thu, 29 Nov 2018 16:05:47 +0000 (17:05 +0100)]
parisc: Enable -ffunction-sections for modules on 32-bit kernel
commit
1e8249b8a4e960018e4baca6b523b8a4500af600 upstream.
Frank Schreiner reported, that since kernel 4.18 he faces sysfs-warnings
when loading modules on a 32-bit kernel. Here is one such example:
sysfs: cannot create duplicate filename '/module/nfs/sections/.text'
CPU: 0 PID: 98 Comm: modprobe Not tainted 4.18.0-2-parisc #1 Debian 4.18.10-2
Backtrace:
[<
1017ce2c>] show_stack+0x3c/0x50
[<
107a7210>] dump_stack+0x28/0x38
[<
103f900c>] sysfs_warn_dup+0x88/0xac
[<
103f8b1c>] sysfs_add_file_mode_ns+0x164/0x1d0
[<
103f9e70>] internal_create_group+0x11c/0x304
[<
103fa0a0>] sysfs_create_group+0x48/0x60
[<
1022abe8>] load_module.constprop.35+0x1f9c/0x23b8
[<
1022b278>] sys_finit_module+0xd0/0x11c
[<
101831dc>] syscall_exit+0x0/0x14
This warning gets triggered by the fact, that due to commit
24b6c22504a2
("parisc: Build kernel without -ffunction-sections") we now get multiple .text
sections in the kernel modules for which sysfs_create_group() can't create
multiple virtual files.
This patch works around the problem by re-enabling the -ffunction-sections
compiler option for modules, while keeping it disabled for the non-module
kernel code.
Reported-by: Frank Scheiner <frank.scheiner@web.de>
Fixes:
24b6c22504a2 ("parisc: Build kernel without -ffunction-sections")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enric Balletbo i Serra [Tue, 4 Dec 2018 15:58:43 +0000 (16:58 +0100)]
Revert "mfd: cros_ec: Use devm_kzalloc for private data"
commit
48a2ca0ee3994df53da230c7079a18a70ec914f9 upstream.
This reverts commit
3aa2177e47878f7e7616da8a2050c44f22301b6e.
That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.
Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.
------------[ cut here ]------------
Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
Modules linked in: btusb btrtl btintel btbcm bluetooth ...
CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
Hardware name: Google Kevin (DT)
pstate:
40000005 (nZcv daif -PAN -UAO)
pc : device_release+0x80/0x90
lr : device_release+0x80/0x90
sp :
ffff00000c47bc70
x29:
ffff00000c47bc70 x28:
ffff8000e86b0d40
x27:
0000000000000000 x26:
0000000000000000
x25:
0000000056000000 x24:
0000000000000015
x23:
ffff8000f0bbf860 x22:
ffff000000d320a0
x21:
ffff8000ee93e100 x20:
ffff8000ed931428
x19:
ffff8000ed931418 x18:
0000000000000020
x17:
0000000000000000 x16:
0000000000000000
x15:
0000000000000400 x14:
0000000000000143
x13:
0000000000000000 x12:
0000000000000400
x11:
0000000000000157 x10:
0000000000000960
x9 :
ffff00000c47b9b0 x8 :
ffff8000e86b1700
x7 :
0000000000000000 x6 :
ffff8000f7d520b8
x5 :
ffff8000f7d520b8 x4 :
0000000000000000
x3 :
ffff8000f7d58e68 x2 :
ffff8000e86b0d40
x1 :
37d859939c964800 x0 :
0000000000000000
Call trace:
device_release+0x80/0x90
kobject_put+0x74/0xe8
device_unregister+0x20/0x30
ec_device_remove+0x34/0x48 [cros_ec_dev]
platform_drv_remove+0x28/0x48
device_release_driver_internal+0x1a8/0x240
driver_detach+0x40/0x80
bus_remove_driver+0x54/0xa8
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
__arm64_sys_delete_module+0x16c/0x1f8
el0_svc_common+0x84/0xd8
el0_svc_handler+0x2c/0x80
el0_svc+0x8/0xc
---[ end trace
a57c4625f3c60ae8 ]---
Cc: stable@vger.kernel.org
Fixes:
3aa2177e4787 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mauro Carvalho Chehab [Fri, 23 Nov 2018 17:10:57 +0000 (12:10 -0500)]
media: dvb-pll: don't re-validate tuner frequencies
commit
3420f65cbbd0555049bd02394bed33a0ef74d860 upstream.
The dvb_frontend core already checks for the frequencies. No
need for any additional check inside the driver.
It is part of the fixes for the following bug:
https://bugzilla.opensuse.org/show_bug.cgi?id=
1116374
Fixes:
a3f90c75b833 ("media: dvb: convert tuner_info frequencies to Hz")
Reported-by: Stakanov Schufter <stakanov@eclipso.eu>
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org # For 4.19
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mauro Carvalho Chehab [Tue, 20 Nov 2018 10:19:36 +0000 (05:19 -0500)]
media: dvb-pll: fix tuner frequency ranges
commit
3d8e450f517cdb33da77827ec75929354753e9c0 upstream.
Tuners should report frequencies in Hz. That works fine on most
drivers, but, in the case of dvb-pll, some settings are for
satellite tuners, while others are for terrestrial/cable ones.
The code was trying to solve it at probing time, but that doesn't
work, as, when _attach is called, the delivery system may be wrong.
Fix it by ensuring that all frequencies are in Hz at the per-tuner
max/min values.
While here, add a debug message, as this would help to debug any
issues there.
It partially fixes the following bug:
https://bugzilla.opensuse.org/show_bug.cgi?id=
1116374
Fixes:
a3f90c75b833 ("media: dvb: convert tuner_info frequencies to Hz")
Reported-by: Stakanov Schufter <stakanov@eclipso.eu>
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org # For 4.19
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans Verkuil [Sat, 17 Nov 2018 11:25:08 +0000 (06:25 -0500)]
media: vicodec: fix memchr() kernel oops
commit
cb3b2ffb757e75fef40fb94bc093cbbf49a6bf6e upstream.
The size passed to memchr is too large as it assumes the search
starts at the start of the buffer, but it can start at an offset.
Cc: <stable@vger.kernel.org> # for v4.19 and up
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans Verkuil [Tue, 20 Nov 2018 10:13:04 +0000 (05:13 -0500)]
media: gspca: fix frame overflow error
commit
f96d84488f7d5f9123428c700cea82a292bca53e upstream.
When converting gspca to vb2 I missed that fact that the buffer sizes
were rounded up to the next page size. As a result some gspca drivers
(spca561 being one of them) reported frame overflows.
Modify the code to align the buffer sizes to the next page size, just
as the original code did.
Fixes:
1f5965c4dfd7 ("media: gspca: convert to vb2")
Tested-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: softwarebugs <softwarebugs@protonmail.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Chiu [Wed, 5 Dec 2018 06:48:56 +0000 (14:48 +0800)]
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G
commit
b72f936f6b325f4fde06b02e4b6ab682f6f2e73f upstream.
Acer AIO Veriton Z4860G/Z6860G with the same ALC286 codec has issues
with the input from external microphone. The issue can be fixed by
the fixup ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE for Veriton Z4660G.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Chiu [Wed, 5 Dec 2018 06:48:55 +0000 (14:48 +0800)]
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G
commit
9f8aefed9623a91dec54eab8908f3810b7f8d73a upstream.
Acer AIO Veriton Z4660G with ALC286 codec has issue with the input
from external microphones connecting via 'Front Mic' jack. The fixup
ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE enables the jack sensing of
the headset and fix the audio input issue of external microphone.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Chiu [Wed, 5 Dec 2018 06:48:54 +0000 (14:48 +0800)]
ALSA: hda/realtek - Add support for Acer Aspire C24-860 headset mic
commit
705b65f107470499442240ff7afee5021a7002a6 upstream.
The Acer AIO Aspire C24-860 with ALC286 can't detect the headset
microphone. Just like another Acer AIO U27-880, it needs a different
pin value for 0x18 and the headset fixup to make headset mic work.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Chiu [Wed, 5 Dec 2018 06:48:53 +0000 (14:48 +0800)]
ALSA: hda/realtek: ALC286 mic and headset-mode fixups for Acer Aspire U27-880
commit
33aaebd48ae2d2c78fef5063a0381e17db19b060 upstream.
Acer Aspire U27-880(AIO) with ALC286 codec can not detect headset mic
and internal mic not working either. It needs the similar quirk like
Sony laptops to fix headphone jack sensing and enables use of the
internal microphone.
Unfortunately jack sensing for the headset mic is still not working.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Mon, 3 Dec 2018 09:44:15 +0000 (10:44 +0100)]
ALSA: hda/realtek - Fix speaker output regression on Thinkpad T570
commit
54947cd64c1b8290f64bb2958e343c07270e3a58 upstream.
We've got a regression report for some Thinkpad models (at least
T570s) which shows the too low speaker output volume. The bisection
leaded to the commit
61fcf8ece9b6 ("ALSA: hda/realtek - Enable Thinkpad
Dock device for ALC298 platform"), and it's basically adding the two
pin configurations for the dock, and looks harmless.
The real culprit seems, though, that the DAC assignment for the
speaker pin is implicitly assumed on these devices, i.e. pin NID 0x14
to be coupled with DAC NID 0x03. When more pins are configured by the
commit above, the auto-parser changes the DAC assignment, and this
resulted in the regression.
As a workaround, just provide the fixed pin / DAC mapping table for
this Thinkpad fixup function. It's no generic solution, but the
problem itself is pretty much device-specific, so must be good
enough.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=
1554304
Fixes:
61fcf8ece9b6 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Thu, 29 Nov 2018 11:05:19 +0000 (12:05 +0100)]
ALSA: pcm: Fix interval evaluation with openmin/max
commit
5363857b916c1f48027e9b96ee8be8376bf20811 upstream.
As addressed in alsa-lib (commit
b420056604f0), we need to fix the
case where the evaluation of PCM interval "(x x+1]" leading to
-EINVAL. After applying rules, such an interval may be translated as
"(x x+1)".
Fixes:
ff2d6acdf6f1 ("ALSA: pcm: Fix snd_interval_refine first/last with open min/max")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Thu, 29 Nov 2018 07:02:49 +0000 (08:02 +0100)]
ALSA: pcm: Call snd_pcm_unlink() conditionally at closing
commit
b51abed8355e5556886623b2772fa6b7598d2282 upstream.
Currently the PCM core calls snd_pcm_unlink() always unconditionally
at closing a stream. However, since snd_pcm_unlink() invokes the
global rwsem down, the lock can be easily contended. More badly, when
a thread runs in a high priority RT-FIFO, it may stall at spinning.
Basically the call of snd_pcm_unlink() is required only for the linked
streams that are already rare occasion. For normal use cases, this
code path is fairly superfluous.
As an optimization (and also as a workaround for the RT problem
above in normal situations without linked streams), this patch adds a
check before calling snd_pcm_unlink() and calls it only when needed.
Reported-by: Chanho Min <chanho.min@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chanho Min [Mon, 26 Nov 2018 05:36:37 +0000 (14:36 +0900)]
ALSA: pcm: Fix starvation on down_write_nonblock()
commit
b888a5f713e4d17faaaff24316585a4eb07f35b7 upstream.
Commit
67ec1072b053 ("ALSA: pcm: Fix rwsem deadlock for non-atomic PCM
stream") fixes deadlock for non-atomic PCM stream. But, This patch
causes antother stuck.
If writer is RT thread and reader is a normal thread, the reader
thread will be difficult to get scheduled. It may not give chance to
release readlocks and writer gets stuck for a long time if they are
pinned to single cpu.
The deadlock described in the previous commit is because the linux
rwsem queues like a FIFO. So, we might need non-FIFO writelock, not
non-block one.
My suggestion is that the writer gives reader a chance to be scheduled
by using the minimum msleep() instaed of spinning without blocking by
writer. Also, The *_nonblock may be changed to *_nonfifo appropriately
to this concept.
In terms of performance, when trylock is failed, this minimum periodic
msleep will have the same performance as the tick-based
schedule()/wake_up_q().
[ Although this has a fairly high performance penalty, the relevant
code path became already rare due to the previous commit ("ALSA:
pcm: Call snd_pcm_unlink() conditionally at closing"). That is, now
this unconditional msleep appears only when using linked streams,
and this must be a rare case. So we accept this as a quick
workaround until finding a more suitable one -- tiwai ]
Fixes:
67ec1072b053 ("ALSA: pcm: Fix rwsem deadlock for non-atomic PCM stream")
Suggested-by: Wonmin Jung <wonmin.jung@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Thu, 29 Nov 2018 08:57:37 +0000 (08:57 +0000)]
ALSA: hda: Add support for AMD Stoney Ridge
commit
3deef52ce10514ccdebba8e8ab85f9cebd0eb3f7 upstream.
It's similar to other AMD audio devices, it also supports D3, which can
save some power drain.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hui Peng [Mon, 3 Dec 2018 15:09:34 +0000 (16:09 +0100)]
ALSA: usb-audio: Fix UAF decrement if card has no live interfaces in card.c
commit
5f8cf712582617d523120df67d392059eaf2fc4b upstream.
If a USB sound card reports 0 interfaces, an error condition is triggered
and the function usb_audio_probe errors out. In the error path, there was a
use-after-free vulnerability where the memory object of the card was first
freed, followed by a decrement of the number of active chips. Moving the
decrement above the atomic_dec fixes the UAF.
[ The original problem was introduced in 3.1 kernel, while it was
developed in a different form. The Fixes tag below indicates the
original commit but it doesn't mean that the patch is applicable
cleanly. -- tiwai ]
Fixes:
362e4e49abe5 ("ALSA: usb-audio - clear chip->probing on error exit")
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Das [Wed, 28 Nov 2018 20:16:37 +0000 (20:16 +0000)]
ALSA: usb-audio: Add SMSL D1 to quirks for native DSD support
commit
44ff57e685f96d0cb9540004cc9d1d880e7a4315 upstream.
This patch adds quirk VID/PID IDs for the SMSL D1 in order to enable
Native DSD support.
[ Moved the added entry in numerical order -- tiwai ]
Signed-off-by: Tony Das <tdas444@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 4 Dec 2018 16:00:36 +0000 (17:00 +0100)]
USB: serial: console: fix reported terminal settings
commit
f51ccf46217c28758b1f3b5bc0ccfc00eca658b2 upstream.
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes:
7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Payer [Wed, 5 Dec 2018 20:19:59 +0000 (21:19 +0100)]
USB: check usb_get_extra_descriptor for proper size
commit
704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Theissen [Tue, 4 Dec 2018 22:43:35 +0000 (23:43 +0100)]
usb: appledisplay: Add 27" Apple Cinema Display
commit
d7859905301880ad3e16272399d26900af3ac496 upstream.
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Harry Pan [Wed, 28 Nov 2018 16:40:41 +0000 (00:40 +0800)]
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device
commit
2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream.
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb
ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yangtao Li [Thu, 22 Nov 2018 12:34:41 +0000 (07:34 -0500)]
net: amd: add missing of_node_put()
[ Upstream commit
c44c749d3b6fdfca39002e7e48e03fe9f9fe37a3 ]
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hangbin Liu [Thu, 22 Nov 2018 08:15:28 +0000 (16:15 +0800)]
team: no need to do team_notify_peers or team_mcast_rejoin when disabling port
[ Upstream commit
5ed9dc99107144f83b6c1bb52a69b58875baf540 ]
team_notify_peers() will send ARP and NA to notify peers. team_mcast_rejoin()
will send multicast join group message to notify peers. We should do this when
enabling/changed to a new port. But it doesn't make sense to do it when a port
is disabled.
On the other hand, when we set mcast_rejoin_count to 2, and do a failover,
team_port_disable() will increase mcast_rejoin.count_pending to 2 and then
team_port_enable() will increase mcast_rejoin.count_pending to 4. We will send
4 mcast rejoin messages at latest, which will make user confused. The same
with notify_peers.count.
Fix it by deleting team_notify_peers() and team_mcast_rejoin() in
team_port_disable().
Reported-by: Liang Li <liali@redhat.com>
Fixes:
fc423ff00df3a ("team: add peer notification")
Fixes:
492b200efdd20 ("team: add support for sending multicast rejoins")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Falcon [Wed, 21 Nov 2018 17:17:59 +0000 (11:17 -0600)]
ibmvnic: Update driver queues after change in ring size support
[ Upstream commit
5bf032ef08e6a110edc1e3bfb3c66a208fb55125 ]
During device reset, queue memory is not being updated to accommodate
changes in ring buffer sizes supported by backing hardware. Track
any differences in ring buffer sizes following the reset and update
queue memory when possible.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Falcon [Wed, 21 Nov 2018 17:17:58 +0000 (11:17 -0600)]
ibmvnic: Fix RX queue buffer cleanup
[ Upstream commit
b7cdec3d699db2e5985ad39de0f25d3b6111928e ]
The wrong index is used when cleaning up RX buffer objects during release
of RX queues. Update to use the correct index counter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tigran Mkrtchyan [Wed, 21 Nov 2018 11:25:41 +0000 (12:25 +0100)]
flexfiles: use per-mirror specified stateid for IO
[ Upstream commit
bb21ce0ad227b69ec0f83279297ee44232105d96 ]
rfc8435 says:
For tight coupling, ffds_stateid provides the stateid to be used by
the client to access the file.
However current implementation replaces per-mirror provided stateid with
by open or lock stateid.
Ensure that per-mirror stateid is used by ff_layout_write_prepare_v4 and
nfs4_ff_layout_prepare_ds.
Signed-off-by: Tigran Mkrtchyan <tigran.mkrtchyan@desy.de>
Signed-off-by: Rick Macklem <rmacklem@uoguelph.ca>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Olga Kornievskaia [Wed, 21 Nov 2018 16:24:22 +0000 (11:24 -0500)]
NFSv4.2 copy do not allocate memory under the lock
[ Upstream commit
99f2c55591fb5c1b536263970d98c2ebc2089906 ]
Bruce pointed out that we shouldn't allocate memory while holding
a lock in the nfs4_callback_offload() and handle_async_copy()
that deal with a racing CB_OFFLOAD and reply to COPY case.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pan Bian [Wed, 21 Nov 2018 09:53:47 +0000 (17:53 +0800)]
iommu/vt-d: Use memunmap to free memremap
[ Upstream commit
829383e183728dec7ed9150b949cd6de64127809 ]
memunmap() should be used to free the return of memremap(), not
iounmap().
Fixes:
dfddb969edf0 ('iommu/vt-d: Switch from ioremap_cache to memremap')
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vincent Chen [Wed, 21 Nov 2018 01:38:11 +0000 (09:38 +0800)]
net: faraday: ftmac100: remove netif_running(netdev) check before disabling interrupts
[ Upstream commit
426a593e641ebf0d9288f0a2fcab644a86820220 ]
In the original ftmac100_interrupt(), the interrupts are only disabled when
the condition "netif_running(netdev)" is true. However, this condition
causes kerenl hang in the following case. When the user requests to
disable the network device, kernel will clear the bit __LINK_STATE_START
from the dev->state and then call the driver's ndo_stop function. Network
device interrupts are not blocked during this process. If an interrupt
occurs between clearing __LINK_STATE_START and stopping network device,
kernel cannot disable the interrupts due to the condition
"netif_running(netdev)" in the ISR. Hence, kernel will hang due to the
continuous interruption of the network device.
In order to solve the above problem, the interrupts of the network device
should always be disabled in the ISR without being restricted by the
condition "netif_running(netdev)".
[V2]
Remove unnecessary curly braces.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
David Abdurachmanov [Thu, 8 Nov 2018 19:07:00 +0000 (20:07 +0100)]
riscv: fix warning in arch/riscv/include/asm/module.h
[ Upstream commit
0138ebb90c633f76bc71617f8f23635ce41c84fd ]
Fixes warning: 'struct module' declared inside parameter list will not be
visible outside of this definition or declaration
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Juliet Kim [Mon, 19 Nov 2018 21:59:22 +0000 (15:59 -0600)]
net/ibmnvic: Fix deadlock problem in reset
[ Upstream commit
a5681e20b541a507c7d4fd48ae4a4040d32ee1ef ]
This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.
Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Denis Bolotin [Mon, 19 Nov 2018 14:28:31 +0000 (16:28 +0200)]
qed: Fix QM getters to always return a valid pq
[ Upstream commit
eb62cca9bee842e5b23bd0ddfb1f271ca95e8759 ]
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes:
b5a9ee7cf3be ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Denis Bolotin [Mon, 19 Nov 2018 14:28:30 +0000 (16:28 +0200)]
qed: Fix bitmap_weight() check
[ Upstream commit
276d43f0ae963312c0cd0e2b9a85fd11ac65dfcc ]
Fix the condition which verifies that only one flag is set. The API
bitmap_weight() should receive size in bits instead of bytes.
Fixes:
b5a9ee7cf3be ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Trond Myklebust [Tue, 20 Nov 2018 01:11:45 +0000 (20:11 -0500)]
NFSv4: Fix a NFSv4 state manager deadlock
[ Upstream commit
aeabb3c96186a0f944fc2b1f25c84d5eb3a93fa9 ]
Fix a deadlock whereby the NFSv4 state manager can get stuck in the
delegation return code, waiting for a layout return to complete in
another thread. If the server reboots before that other thread
completes, then we need to be able to start a second state
manager thread in order to perform recovery.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Arthur Kiyanovski [Mon, 19 Nov 2018 10:05:20 +0000 (12:05 +0200)]
net: ena: fix crash during failed resume from hibernation
[ Upstream commit
e76ad21d070f79e566ac46ce0b0584c3c93e1b43 ]
During resume from hibernation if ena_restore_device fails,
ena_com_dev_reset() is called, and uses the readless read mechanism,
which was already destroyed by the call to
ena_com_mmio_reg_read_request_destroy(). This causes a NULL pointer
reference.
In this commit we switch the call order of the above two functions
to avoid this crash.
Fixes:
d7703ddbd7c9 ("net: ena: fix rare bug when failed restart/resume is followed by driver removal")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thor Thayer [Fri, 16 Nov 2018 14:25:49 +0000 (08:25 -0600)]
mtd: spi-nor: Fix Cadence QSPI page fault kernel panic
[ Upstream commit
a6a66f80c85e8e20573ca03fabf32445954a88d5 ]
The current Cadence QSPI driver caused a kernel panic sporadically
when writing to QSPI. The problem was caused by writing more bytes
than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 11.202044] Unable to handle kernel paging request at virtual address
bffd3000
[ 11.209254] pgd =
e463054d
[ 11.211948] [
bffd3000] *pgd=
2fffb811, *pte=
00000000, *ppte=
00000000
[ 11.218202] Internal error: Oops: 7 [#1] SMP ARM
[ 11.222797] Modules linked in:
[ 11.225844] CPU: 1 PID: 1317 Comm: systemd-hwdb Not tainted 4.17.7-
d0c45cd44a8f
[ 11.235796] Hardware name: Altera SOCFPGA Arria10
[ 11.240487] PC is at __raw_writesl+0x70/0xd4
[ 11.244741] LR is at cqspi_write+0x1a0/0x2cc
</snip>
On a page boundary limit the number of bytes copied from the tx buffer
to remain within the page.
This patch uses a temporary buffer to hold the 4 bytes to write and then
copies only the bytes required from the tx buffer.
Reported-by: Adrian Amborzewicz <adrian.ambrozewicz@intel.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kai-Heng Feng [Wed, 14 Nov 2018 05:35:20 +0000 (05:35 +0000)]
HID: multitouch: Add pointstick support for Cirque Touchpad
[ Upstream commit
12d43aacf9a74d0eb66fd0ea54ebeb79ca28940f ]
Cirque Touchpad/Pointstick combo is similar to Alps devices, it requires
MT_CLS_WIN_8_DUAL to expose its pointstick as a mouse.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
David Herrmann [Wed, 14 Nov 2018 13:16:42 +0000 (14:16 +0100)]
Revert "HID: uhid: use strlcpy() instead of strncpy()"
[ Upstream commit
4d26d1d1e8065bb3326a7c06d5d4698e581443a9 ]
This reverts commit
336fd4f5f25157e9e8bd50e898a1bbcd99eaea46.
Please note that `strlcpy()` does *NOT* do what you think it does.
strlcpy() *ALWAYS* reads the full input string, regardless of the
'length' parameter. That is, if the input is not zero-terminated,
strlcpy() will *READ* beyond input boundaries. It does this, because it
always returns the size it *would* copy if the target was big enough,
not the truncated size it actually copied.
The original code was perfectly fine. The hid device is
zero-initialized and the strncpy() functions copied up to n-1
characters. The result is always zero-terminated this way.
This is the third time someone tried to replace strncpy with strlcpy in
this function, and gets it wrong. I now added a comment that should at
least make people reconsider.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dave Gerlach [Tue, 13 Nov 2018 19:30:40 +0000 (13:30 -0600)]
cpufreq: ti-cpufreq: Only register platform_device when supported
[ Upstream commit
d98ccfc3948ab63152494bb6b9c17e15295c0310 ]
Currently the ti-cpufreq driver blindly registers a 'ti-cpufreq' to force
the driver to probe on any platforms where the driver is built in.
However, this should only happen on platforms that actually can make use
of the driver. There is already functionality in place to match the
SoC compatible so let's factor this out into a separate call and
make sure we find a match before creating the ti-cpufreq platform device.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Olof Johansson [Sat, 17 Nov 2018 03:43:27 +0000 (19:43 -0800)]
mtd: rawnand: qcom: Namespace prefix some commands
[ Upstream commit
33bf5519ae5dd356b182a94e3622f42860274a38 ]
PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Caught by riscv allmodconfig.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Brenda J. Butler [Fri, 16 Nov 2018 22:37:56 +0000 (17:37 -0500)]
tc-testing: tdc.py: Guard against lack of returncode in executed command
[ Upstream commit
c6cecf4ae44e4ce9158ef8806358142c3512cd33 ]
Add some defensive coding in case one of the subprocesses created by tdc
returns nothing. If no object is returned from exec_cmd, then tdc will
halt with an unhandled exception.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lucas Bates [Fri, 16 Nov 2018 22:37:55 +0000 (17:37 -0500)]
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
[ Upstream commit
5aaf6428526bcad98d6f51f2f679c919bb75d7e9 ]
Prevent exceptions from being raised while decoding output
from an executed command. There is no impact on tdc's
execution and the verify command phase would fail the pattern
match.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bartosz Golaszewski [Thu, 8 Nov 2018 16:52:53 +0000 (17:52 +0100)]
gpio: mockup: fix indicated direction
[ Upstream commit
bff466bac59994cfcceabe4d0be5fdc1c20cd5b8 ]
Commit
3edfb7bd76bd ("gpiolib: Show correct direction from the
beginning") fixed an existing issue but broke libgpiod tests by
changing the default direction of dummy lines to output.
We don't break user-space so make gpio-mockup behave as before.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Robert Jarzmik [Thu, 15 Nov 2018 17:16:38 +0000 (18:16 +0100)]
gpio: pxa: fix legacy non pinctrl aware builds again
[ Upstream commit
70cdb6ad6dc342d9643a00c9092e88f0075f2b9a ]
As pointed out by Gregor, spitz keyboard matrix is broken, with or
without CONFIG_PINCTRL set, quoting :
"The gpio matrix keypard on the Zaurus C3x00 (see spitz.c) does not work
properly. Noticeable are that rshift+c does nothing where as lshift+c
creates C. Opposite it is for rshift+a vs lshift+a, here only rshift
works. This affects a few other combinations using the rshift or lshift
buttons."
As a matter of fact, as for platform_data based builds CONFIG_PINCTRL=n
is required for now (as opposed for devicetree builds where it should be
set), this means gpio driver should change the direction, which is what
was attempted by commit
c4e5ffb6f224 ("gpio: pxa: fix legacy non pinctrl
aware builds").
Unfortunately, the input case was inverted, and the direction change was
never done. This wasn't seen up until now because the initial platform
setup (MFP) was setting this direction. Yet in Gregory's case, the
matrix-keypad driver changes back and forth the direction dynamically,
and this is why he's the first to report it.
Fixes:
c4e5ffb6f224 ("gpio: pxa: fix legacy non pinctrl aware builds")
Tested-by: Greg <greguu@null.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrew Morton [Fri, 16 Nov 2018 00:15:20 +0000 (16:15 -0800)]
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
[ Upstream commit
a97b9565338350d70d8d971c4ee6f0d4fa967418 ]
Add missing semicolon.
Fixes:
291d57f67d244973 ("qed: Fix rdma_info structure allocation")
Cc: Michal Kalderon <michal.kalderon@cavium.com>
Cc: Denis Bolotin <denis.bolotin@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aya Levin [Thu, 15 Nov 2018 16:05:15 +0000 (18:05 +0200)]
net/mlx4: Fix UBSAN warning of signed integer overflow
[ Upstream commit
a463146e67c848cbab5ce706d6528281b7cded08 ]
UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow:
1802201963 +
1802201963 cannot be represented
in type 'int'
The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative. Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.
Fixes:
5a0d0a6161ae ("mlx4: Structures and init/teardown for VF resource quotas")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tariq Toukan [Thu, 15 Nov 2018 16:05:14 +0000 (18:05 +0200)]
net/mlx4_core: Fix uninitialized variable compilation warning
[ Upstream commit
3ea7e7ea53c9f6ee41cb69a29c375fe9dd9a56a7 ]
Initialize the uid variable to zero to avoid the compilation warning.
Fixes:
7a89399ffad7 ("net/mlx4: Add mlx4_bitmap zone allocator")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jack Morgenstein [Thu, 15 Nov 2018 16:05:13 +0000 (18:05 +0200)]
net/mlx4_core: Zero out lkey field in SW2HW_MPT fw command
[ Upstream commit
bd85fbc2038a1bbe84990b23ff69b6fc81a32b2c ]
When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.
This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).
The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).
Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.
Fixes:
e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicholas Kazlauskas [Thu, 15 Nov 2018 22:21:34 +0000 (17:21 -0500)]
drm/amd/display: Support amdgpu "max bpc" connector property (v2)
[ Upstream commit
07e3a1cfb0568b6d8d7862077029af96af6690ea ]
[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.
Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.
This should be a user configurable option such that the user can select
what bpc configuration they would like.
[How]
This patch adds support for getting and setting the amdgpu driver
specific "max bpc" property on the connector.
It also adds support for limiting the output bpc based on the property
value. The default limitation is the lowest value in the range, 8bpc.
This was the old value before the range was uncapped.
This patch should be updated/replaced later once common drm support
for max bpc lands.
Bugzilla: https://bugs.freedesktop.org/108542
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201585
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200645
Fixes:
e03fd3f300f6 ("drm/amd/display: Do not limit color depth to 8bpc")
v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicholas Kazlauskas [Thu, 15 Nov 2018 22:19:12 +0000 (17:19 -0500)]
drm/amdgpu: Add amdgpu "max bpc" connector property (v2)
[ Upstream commit
69756c6ff0de478c10100481f16c966dde3b5339 ]
[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.
Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.
This should be a user configurable option such that the user can select
what bpc configuration they would like.
[How]
This patch introduces the "max bpc" amdgpu driver specific connector
property so the user can limit the maximum bpc. It ranges from 8 to 16.
This doesn't directly set the preferred bpc for the panel since it
follows Intel's existing driver conventions.
This proprety should be removed once common drm support for max bpc
lands.
v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vasundhara Volam [Thu, 15 Nov 2018 08:25:42 +0000 (03:25 -0500)]
bnxt_en: Fix filling time in bnxt_fill_coredump_record()
[ Upstream commit
8dc5ae2d48976764cf3498e97963fa06befefb0e ]
Fix the year and month offset while storing it in
bnxt_fill_coredump_record().
Fixes:
6c5657d085ae ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Thu, 15 Nov 2018 00:35:10 +0000 (16:35 -0800)]
nvme-fc: resolve io failures during connect
[ Upstream commit
4cff280a5fccf6513ed9e895bb3a4e7ad8b0cedc ]
If an io error occurs on an io issued while connecting, recovery
of the io falls flat as the state checking ends up nooping the error
handler.
Create an err_work work item that is scheduled upon an io error while
connecting. The work thread terminates all io on all queues and marks
the queues as not connected. The termination of the io will return
back to the callee, which will then back out of the connection attempt
and will reschedule, if possible, the connection attempt.
The changes:
- in case there are several commands hitting the error handler, a
state flag is kept so that the error work is only scheduled once,
on the first error. The subsequent errors can be ignored.
- The calling sequence to stop keep alive and terminate the queues
and their io is lifted from the reset routine. Made a small
service routine used by both reset and err_work.
- During debugging, found that the teardown path can reference
an uninitialized pointer, resulting in a NULL pointer oops.
The aen_ops weren't initialized yet. Add validation on their
initialization before calling the teardown routine.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ursula Braun [Mon, 12 Nov 2018 16:06:12 +0000 (17:06 +0100)]
s390/ism: clear dmbe_mask bit before SMC IRQ handling
[ Upstream commit
007b656851ed7f94ba0fa358ac3e5d7705da6846 ]
SMC-D stress workload showed connection stalls. Since the firmware
decides to skip raising an interrupt if the SBA DMBE mask bit is
still set, this SBA DMBE mask bit should be cleared before the
IRQ handling in the SMC code runs. Otherwise there are small windows
possible with missing interrupts for incoming data.
SMC-D currently does not care about the old value of the SBA DMBE
mask.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shen Jing [Thu, 1 Nov 2018 10:05:17 +0000 (15:35 +0530)]
Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
[ Upstream commit
a9c859033f6ec772f8e3228c343bb1321584ae0e ]
This reverts commit
b4194da3f9087dd38d91b40f9bec42d59ce589a8
since it causes list corruption followed by kernel panic:
Workqueue: adb ffs_aio_cancel_worker
RIP: 0010:__list_add_valid+0x4d/0x70
Call Trace:
insert_work+0x47/0xb0
__queue_work+0xf6/0x400
queue_work_on+0x65/0x70
dwc3_gadget_giveback+0x44/0x50 [dwc3]
dwc3_gadget_ep_dequeue+0x83/0x2d0 [dwc3]
? finish_wait+0x80/0x80
usb_ep_dequeue+0x1e/0x90
process_one_work+0x18c/0x3b0
worker_thread+0x3c/0x390
? process_one_work+0x3b0/0x3b0
kthread+0x11e/0x140
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x3a/0x50
This issue is seen with warm reboot stability testing.
Signed-off-by: Shen Jing <jingx.shen@intel.com>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Carpenter [Thu, 18 Oct 2018 07:36:47 +0000 (10:36 +0300)]
usb: dwc2: pci: Fix an error code in probe
[ Upstream commit
3c135e8900199e3b9375c1eff808cceba2ee37de ]
We added some error handling to this function but forgot to set the
error code on this path.
Fixes:
ecd29dabb2ba ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Denis Bolotin [Mon, 12 Nov 2018 10:50:23 +0000 (12:50 +0200)]
qed: Fix reading wrong value in loop condition
[ Upstream commit
ed4eac20dcffdad47709422e0cb925981b056668 ]
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Kalderon [Mon, 12 Nov 2018 10:50:22 +0000 (12:50 +0200)]
qed: Fix rdma_info structure allocation
[ Upstream commit
291d57f67d2449737d1e370ab5b9a583818eaa0c ]
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes:
51ff17251c9c ("qed: Add support for RoCE hw init")
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Denis Bolotin [Mon, 12 Nov 2018 10:50:21 +0000 (12:50 +0200)]
qed: Fix overriding offload_tc by protocols without APP TLV
[ Upstream commit
e90202ed1cf9672c48a363c84a929932ebfe6fc0 ]
The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Denis Bolotin [Mon, 12 Nov 2018 10:50:20 +0000 (12:50 +0200)]
qed: Fix PTT leak in qed_drain()
[ Upstream commit
9aaa4e8ba12972d674caeefbc5f88d83235dd697 ]
Release PTT before entering error flow.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sudarsana Reddy Kalluru [Mon, 12 Nov 2018 02:27:34 +0000 (18:27 -0800)]
bnx2x: Assign unique DMAE channel number for FW DMAE transactions.
[ Upstream commit
77e461d14ed141253573eeeb4d34eccc51e38328 ]
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Filippo Sironi [Mon, 12 Nov 2018 12:26:30 +0000 (12:26 +0000)]
amd/iommu: Fix Guest Virtual APIC Log Tail Address Register
[ Upstream commit
ab99be4683d9db33b100497d463274ebd23bd67e ]
This register should have been programmed with the physical address
of the memory location containing the shadow tail pointer for
the guest virtual APIC log instead of the base address.
Fixes:
8bda0cfbdc1a ('iommu/amd: Detect and initialize guest vAPIC log')
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: Wei Wang <wawei@amazon.de>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sven Eckelmann [Wed, 7 Nov 2018 22:09:12 +0000 (23:09 +0100)]
batman-adv: Expand merged fragment buffer for full packet
[ Upstream commit
d7d8bbb40a5b1f682ee6589e212934f4c6b8ad60 ]
The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes:
610bfc6bc99b ("batman-adv: Receive fragmented packets and merge")
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sven Eckelmann [Tue, 30 Oct 2018 11:17:10 +0000 (12:17 +0100)]
batman-adv: Use explicit tvlv padding for ELP packets
[ Upstream commit
f4156f9656feac21f4de712fac94fae964c5d402 ]
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
Fixes:
d6f94d91f766 ("batman-adv: ELP - adding basic infrastructure")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Benson Leung [Thu, 8 Nov 2018 23:59:21 +0000 (15:59 -0800)]
HID: input: Ignore battery reported by Symbol DS4308
[ Upstream commit
0fd791841a6d67af1155a9c3de54dea51220721e ]
The Motorola/Zebra Symbol DS4308-HD is a handheld USB barcode scanner
which does not have a battery, but reports one anyway that always has
capacity 2.
Let's apply the IGNORE quirk to prevent it from being treated like a
power supply so that userspaces don't get confused that this
accessory is almost out of power and warn the user that they need to charge
their wired barcode scanner.
Reported here: https://bugs.chromium.org/p/chromium/issues/detail?id=804720
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Colin Ian King [Fri, 19 Oct 2018 12:58:01 +0000 (13:58 +0100)]
test_firmware: fix error return getting clobbered
[ Upstream commit
8bb0a88600f0267cfcc245d34f8c4abe8c282713 ]
In the case where eq->fw->size > PAGE_SIZE the error return rc
is being set to EINVAL however this is being overwritten to
rc = req->fw->size because the error exit path via label 'out' is
not being taken. Fix this by adding the jump to the error exit
path 'out'.
Detected by CoverityScan, CID#
1453465 ("Unused value")
Fixes:
c92316bf8e94 ("test_firmware: add batched firmware tests")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabrizio Castro [Mon, 10 Sep 2018 10:43:13 +0000 (11:43 +0100)]
can: rcar_can: Fix erroneous registration
[ Upstream commit
68c8d209cd4337da4fa04c672f0b62bb735969bc ]
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes:
862e2b6af9413b43 ("can: rcar_can: support all input clocks")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
YueHaibing [Wed, 29 Aug 2018 01:46:54 +0000 (01:46 +0000)]
can: ucan: remove set but not used variable 'udev'
[ Upstream commit
207681fc5f3d5d398f106d1ae0080fc2373f707a ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
struct usb_device *udev;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wei Li [Thu, 8 Nov 2018 17:08:29 +0000 (09:08 -0800)]
scsi: ufs: Fix hynix ufs bug with quirk on hi36xx SoC
[ Upstream commit
8e4829c6f7470722c1f5a1dc5769ebe09ef036d6 ]
Hynix ufs has deviations on hi36xx platform which will result in ufs bursts
transfer failures.
To fix the problem, the Hynix device must set the register
VS_DebugSaveConfigTime to 0x10, which will set time reference for
SaveConfigTime is 250 ns. The time reference for SaveConfigTime is 40 ns by
default.
This patch is necessary to boot on HiKey960 boards that use Hynix UFS chips
(H28U62301AMR model: hB8aL1).
Cc: Vinayak Holikatti <vinholikatti@gmail.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Wei Li <liwei213@huawei.com>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
[jstultz: Forward ported from older code, slight tweak to commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Geert Uytterhoeven [Wed, 7 Nov 2018 13:18:50 +0000 (14:18 +0100)]
iommu/ipmmu-vmsa: Fix crash on early domain free
[ Upstream commit
e5b78f2e349eef5d4fca5dc1cf5a3b4b2cc27abd ]
If iommu_ops.add_device() fails, iommu_ops.domain_free() is still
called, leading to a crash, as the domain was only partially
initialized:
ipmmu-vmsa
e67b0000.mmu: Cannot accommodate DMA translation for IOMMU page tables
sata_rcar
ee300000.sata: Unable to initialize IPMMU context
iommu: Failed to add device
ee300000.sata to group 0: -22
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000038
...
Call trace:
ipmmu_domain_free+0x1c/0xa0
iommu_group_release+0x48/0x68
kobject_put+0x74/0xe8
kobject_del.part.0+0x3c/0x50
kobject_put+0x60/0xe8
iommu_group_get_for_dev+0xa8/0x1f0
ipmmu_add_device+0x1c/0x40
of_iommu_configure+0x118/0x190
Fix this by checking if the domain's context already exists, before
trying to destroy it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Fixes:
d25a2a16f0889 ('iommu: Add driver for Renesas VMSA-compatible IPMMU')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Arnd Bergmann [Mon, 5 Nov 2018 15:51:47 +0000 (16:51 +0100)]
mt76: fix building without CONFIG_LEDS_CLASS
[ Upstream commit
b374e8686fc35ae124e62dc78725ea656ba1ef8a ]
When CONFIG_LEDS_CLASS is disabled, or it is a loadable module while
mt76 is built-in, we run into a link error:
drivers/net/wireless/mediatek/mt76/mac80211.o: In function `mt76_register_device':
mac80211.c:(.text+0xb78): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_of_led_classdev_register'
We don't really need a hard dependency here as the driver can presumably
work just fine without LEDs, so this follows the iwlwifi example and
adds a separate Kconfig option for the LED support, this will be available
whenever it will link, and otherwise the respective code gets left out from
the driver object.
Fixes:
17f1de56df05 ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rafał Miłecki [Fri, 26 Oct 2018 10:50:39 +0000 (12:50 +0200)]
brcmutil: really fix decoding channel info for 160 MHz bandwidth
[ Upstream commit
3401d42c7ea2d064d15c66698ff8eb96553179ce ]
Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.
This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
Before: chnum:50 control_ch_num:36
After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
Before: chnum:114 control_ch_num:100
After: chnum:114 control_ch_num:120
Fixes:
330994e8e8ec ("brcmfmac: fix for proper support of 160MHz bandwidth")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lu Baolu [Mon, 5 Nov 2018 02:18:58 +0000 (10:18 +0800)]
iommu/vt-d: Fix NULL pointer dereference in prq_event_thread()
[ Upstream commit
19ed3e2dd8549c1a34914e8dad01b64e7837645a ]
When handling page request without pasid event, go to "no_pasid"
branch instead of "bad_req". Otherwise, a NULL pointer deference
will happen there.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Fixes:
a222a7f0bb6c9 'iommu/vt-d: Implement page request handling'
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sakari Ailus [Wed, 10 Oct 2018 08:01:05 +0000 (04:01 -0400)]
media: ipu3-cio2: Unregister device nodes first, then release resources
[ Upstream commit
32388d6ef7cffc7d8291b67f8dfa26acd45217fd ]
While there are issues related to object lifetime management, unregister
the media device first, followed immediately by other device nodes when
the driver is being unbound. Only then the resources needed by the driver
may be released. This is slightly safer.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sakari Ailus [Tue, 9 Oct 2018 11:49:49 +0000 (07:49 -0400)]
media: omap3isp: Unregister media device as first
[ Upstream commit
30efae3d789cd0714ef795545a46749236e29558 ]
While there are issues related to object lifetime management, unregister the
media device first when the driver is being unbound. This is slightly
safer.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Wed, 10 Oct 2018 11:12:15 +0000 (07:12 -0400)]
media: cec: check for non-OK/NACK conditions while claiming a LA
[ Upstream commit
55623b4169056d7bb493d1c6f715991f8db67302 ]
During the configuration phase of a CEC adapter it is trying to claim a
free logical address by polling.
However, the code doesn't check if there were errors other than OK or NACK,
those are just treated as if the poll was NACKed.
Instead check for such errors and retry the poll. And if the problem persists
then don't claim this LA since there is something weird going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Wed, 10 Oct 2018 07:03:43 +0000 (03:03 -0400)]
media: vicodec: lower minimum height to 360
[ Upstream commit
7cf7b2e977abf3f992036939e35a8eab60013aff ]
Lower the minimum height to 360 to be consistent with the webcam input of vivid.
The 480 was rather arbitrary but it made it harder to use vivid as a source for
encoding since the default resolution when you load vivid is 640x360.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Sat, 8 Dec 2018 11:59:10 +0000 (12:59 +0100)]
Linux 4.19.8
Jens Axboe [Fri, 7 Dec 2018 05:17:44 +0000 (22:17 -0700)]
blk-mq: punt failed direct issue to dispatch list
commit
c616cbee97aed4bc6178f148a7240206dcdb85a6 upstream.
After the direct dispatch corruption fix, we permanently disallow direct
dispatch of non read/write requests. This works fine off the normal IO
path, as they will be retried like any other failed direct dispatch
request. But for the blk_insert_cloned_request() that only DM uses to
bypass the bottom level scheduler, we always first attempt direct
dispatch. For some types of requests, that's now a permanent failure,
and no amount of retrying will make that succeed. This results in a
livelock.
Instead of making special cases for what we can direct issue, and now
having to deal with DM solving the livelock while still retaining a BUSY
condition feedback loop, always just add a request that has been through
->queue_rq() to the hardware queue dispatch list. These are safe to use
as no merging can take place there. Additionally, if requests do have
prepped data from drivers, we aren't dependent on them not sharing space
in the request structure to safely add them to the IO scheduler lists.
This basically reverts
ffe81d45322c and is based on a patch from Ming,
but with the list insert case covered as well.
Fixes:
ffe81d45322c ("blk-mq: fix corruption with direct issue")
Cc: stable@vger.kernel.org
Suggested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guoqing Jiang [Fri, 19 Oct 2018 04:08:22 +0000 (12:08 +0800)]
tipc: use destination length for copy string
commit
29e270fc32192e7729057963ae7120663856c93e upstream.
Got below warning with gcc 8.2 compiler.
net/tipc/topsrv.c: In function ‘tipc_topsrv_start’:
net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=]
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/topsrv.c:660:27: note: length computed here
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~
So change it to correct length and use strscpy.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Brodkin [Tue, 20 Nov 2018 10:30:19 +0000 (13:30 +0300)]
arc: [devboards] Add support of NFSv3 ACL
commit
6b04114f6fae5e84d33404c2970b1949c032546e upstream.
By default NFSv3 doesn't support ACL (Access Control Lists)
which might be quite convenient to have so that
mounted NFS behaves exactly as any other local file-system.
In particular missing support of ACL makes umask useless.
This among other thigs fixes Glibc's "nptl/tst-umask1".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Cupertino Miranda <cmiranda@synopsys.com>
Cc: stable@vger.kernel.org #4.14+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kevin Hilman [Fri, 30 Nov 2018 12:51:56 +0000 (15:51 +0300)]
ARC: change defconfig defaults to ARCv2
commit
b7cc40c32a8bfa6f2581a71747f6a7d491fe43ba upstream.
Change the default defconfig (used with 'make defconfig') to the ARCv2
nsim_hs_defconfig, and also switch the default Kconfig ISA selection to
ARCv2.
This allows several default defconfigs (e.g. make defconfig, make
allnoconfig, make tinyconfig) to all work with ARCv2 by default.
Note since we change default architecture from ARCompact to ARCv2
it's required to explicitly mention architecture type in ARCompact
defconfigs otherwise ARCv2 will be implied and binaries will be
generated for ARCv2.
Cc: <stable@vger.kernel.org> # 4.4.x
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Fri, 23 Nov 2018 01:06:36 +0000 (09:06 +0800)]
btrfs: tree-checker: Don't check max block group size as current max chunk size limit is unreliable
commit
10950929e994c5ecee149ff0873388d3c98f12b5 upstream.
[BUG]
A completely valid btrfs will refuse to mount, with error message like:
BTRFS critical (device sdb2): corrupt leaf: root=2 block=
239681536 slot=172 \
bg_start=
12018974720 bg_len=
10888413184, invalid block group size, \
have
10888413184 expect (0,
10737418240]
This has been reported several times as the 4.19 kernel is now being
used. The filesystem refuses to mount, but is otherwise ok and booting
4.18 is a workaround.
Btrfs check returns no error, and all kernels used on this fs is later
than 2011, which should all have the 10G size limit commit.
[CAUSE]
For a 12 devices btrfs, we could allocate a chunk larger than 10G due to
stripe stripe bump up.
__btrfs_alloc_chunk()
|- max_stripe_size = 1G
|- max_chunk_size = 10G
|- data_stripe = 11
|- if (1G * 11 > 10G) {
stripe_size =
976128930;
stripe_size = round_up(
976128930, SZ_16M) =
989855744
However the final stripe_size (
989855744) * 11 =
10888413184, which is
still larger than 10G.
[FIX]
For the comprehensive check, we need to do the full check at chunk read
time, and rely on bg <-> chunk mapping to do the check.
We could just skip the length check for now.
Fixes:
fce466eab7ac ("btrfs: tree-checker: Verify block_group_item")
Cc: stable@vger.kernel.org # v4.19+
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adam Wong [Thu, 29 Nov 2018 18:04:35 +0000 (10:04 -0800)]
Input: elan_i2c - add support for ELAN0621 touchpad
commit
bf87ade0dd7f8cf19dac4d3161d5e86abe0c062b upstream.
Added the ability to detect the ELAN0621 touchpad found in some Lenovo
laptops.
Signed-off-by: Adam Wong <adam@adamwong.me>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noah Westervelt [Thu, 29 Nov 2018 18:10:35 +0000 (10:10 -0800)]
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
commit
ad33429cd02565c28404bb16ae7a4c2bdfda6626 upstream.
Add ELAN061E to the ACPI table to support Elan touchpad found in Lenovo
IdeaPad 330-15ARR.
Signed-off-by: Noah Westervelt <nwestervelt@outlook.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patrick Gaskin [Mon, 12 Nov 2018 19:12:24 +0000 (11:12 -0800)]
Input: elan_i2c - add ELAN0620 to the ACPI table
commit
3ed64da3b790be7c63601e8ca6341b7dff74a660 upstream.
Add ELAN0620 to the ACPI table to support the elan touchpad in
the Lenovo IdeaPad 130-15IKB.
Signed-off-by: Patrick Gaskin <patrick@pgaskin.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>