OSDN Git Service
Saurabh [Tue, 17 Jul 2012 09:44:49 +0000 (09:44 +0000)]
net/ipv4: VTI support rx-path hook in xfrm4_mode_tunnel.
Incorporated David and Steffen's comments.
Add hook for rx-path xfmr4_mode_tunnel for VTI tunnel module.
Signed-off-by: Saurabh Mohan <saurabh.mohan@vyatta.com>
Reviewed-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Riesch [Wed, 18 Jul 2012 10:56:52 +0000 (12:56 +0200)]
asix: Fix return value in AX88172A driver bind function
Return -ENOTSUPP if the initialization fails because the
device is configured for a mode that is not supported by the driver.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Jul 2012 12:29:30 +0000 (12:29 +0000)]
tcp: refine SYN handling in tcp_validate_incoming
Followup of commit
0c24604b68fc (tcp: implement RFC 5961 4.2)
As reported by Vijay Subramanian, we should send a challenge ACK
instead of a dup ack if a SYN flag is set on a packet received out of
window.
This permits the ratelimiting to work as intended, and to increase
correct SNMP counters.
Suggested-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Cc: Kiran Kumar Kella <kkiran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Jul 2012 12:19:48 +0000 (12:19 +0000)]
bonding: refine IFF_XMIT_DST_RELEASE capability
Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.
bonding currently disables IFF_XMIT_DST_RELEASE unconditionally.
If all slaves have the IFF_XMIT_DST_RELEASE bit set, then
bonding master can also have it in its priv_flags
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Tue, 17 Jul 2012 11:14:32 +0000 (11:14 +0000)]
net: qmi_wwan: make dynamic device IDs work
The usbnet API use the device ID table to store a pointer to
a minidriver. Setting a generic pointer for dynamic device
IDs will in most cases make them work as expected. usbnet
will otherwise treat the dynamic IDs as blacklisted. That is
rarely useful.
There is no standard class describing devices supported by
this driver, and most vendors don't even provide enough
information to allow vendor specific wildcard matching. The
result is that most of the supported devices must be
explicitly listed in the device table. Allowing dynamic IDs
to work both simplifies testing and verification of new
devices, and provides a way for end users to use a device
before the ID is added to the driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Groeneveld [Tue, 17 Jul 2012 17:46:01 +0000 (17:46 +0000)]
b44: add 64 bit stats
Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Padmanabh Ratnakar [Wed, 18 Jul 2012 02:52:15 +0000 (02:52 +0000)]
be2net: Ignore physical link async event for Lancer
The ability of driver to transmit packets depends on logical state
of the link. Ignore physical link status.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Padmanabh Ratnakar [Wed, 18 Jul 2012 02:51:58 +0000 (02:51 +0000)]
be2net: Fix VF driver load for Lancer
Lancer FW has added new capability checks for VFs.
Driver should only use those capabilities which are allowed for VFs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jul 2012 16:20:03 +0000 (09:20 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next
Jerr Kirsher says:
====================
This series contains updates to ixgbe & ixgbevf.
...
Alexander Duyck (6):
ixgbe: Ping the VFs on link status change to trigger link change
ixgbe: Handle failures in the ixgbe_setup_rx/tx_resources calls
ixgbe: Move configuration of set_real_num_rx/tx_queues into open
ixgbe: Update the logic for ixgbe_cache_ring_dcb and DCB RSS
configuration
ixgbe: Cleanup logic for MRQC and MTQC configuration
ixgbevf: Update descriptor macros to accept pointers and drop _ADV
suffix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jul 2012 16:10:26 +0000 (09:10 -0700)]
Merge branch 'davem-next.r8169' of git://violet.fr.zoreil.com/romieu/linux
Francois Romieu says:
====================
Francois Romieu (1):
r8169: verbose error message.
Hayes Wang (1):
r8169: remove rtl_ocpdr_cond.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jul 2012 16:08:36 +0000 (09:08 -0700)]
Merge branch 'for-davem' of git://git./linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
1. Fix potential badness when running a self-test with SR-IOV enabled.
2. Fix calculation of some interface statistics that could run backward.
3. Miscellaneous cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Jul 2012 21:38:04 +0000 (21:38 +0000)]
ipv6: fix inet6_csk_xmit()
We should provide to inet6_csk_route_socket a struct flowi6 pointer,
so that net6_csk_xmit() works correctly instead of sending garbage.
Also add some consts
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 11 May 2012 08:33:00 +0000 (08:33 +0000)]
ixgbevf: Update descriptor macros to accept pointers and drop _ADV suffix
This change updates the descriptor macros to accept pointers, updates the
name to drop the _ADV suffix, and include the IXGBEVF name in the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 18 May 2012 06:34:02 +0000 (06:34 +0000)]
ixgbe: Cleanup logic for MRQC and MTQC configuration
This change is meant to make the code much more readable for MTQC and MRQC
configuration.
The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
DCB
En Dis
VMDq En VMDQ/DCB VMDq/RSS
Dis DCB/RSS RSS
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 22 Jun 2012 06:46:33 +0000 (06:46 +0000)]
ixgbe: Update the logic for ixgbe_cache_ring_dcb and DCB RSS configuration
This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.
In this patch I basically did 3 things. I updated the logic for getting
the first register index. I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register. Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 12 Jul 2012 05:52:53 +0000 (05:52 +0000)]
ixgbe: Move configuration of set_real_num_rx/tx_queues into open
It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues. By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 18 May 2012 06:33:47 +0000 (06:33 +0000)]
ixgbe: Handle failures in the ixgbe_setup_rx/tx_resources calls
Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls. Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go. This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Sat, 5 May 2012 05:30:38 +0000 (05:30 +0000)]
ixgbe: Ping the VFs on link status change to trigger link change
When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.
This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Francois Romieu [Wed, 11 Jul 2012 21:39:51 +0000 (23:39 +0200)]
r8169: verbose error message.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Hayes Wang [Wed, 11 Jul 2012 12:31:56 +0000 (20:31 +0800)]
r8169: remove rtl_ocpdr_cond.
It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Francois Romieu <romieu@fr.zoreil.com>
Eric Dumazet [Tue, 17 Jul 2012 20:42:13 +0000 (22:42 +0200)]
ipv4: fix rcu splat
free_nh_exceptions() should use rcu_dereference_protected(..., 1)
since its called after one RCU grace period.
Also add some const-ification in recent code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jul 2012 20:23:08 +0000 (13:23 -0700)]
ipv4: Fix nexthop exception hash computation.
Need to mask it with (FNHE_HASH_SIZE - 1).
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jul 2012 17:48:26 +0000 (10:48 -0700)]
Merge branch 'nexthop_exceptions'
These patches implement the final mechanism necessary to really allow
us to go without the route cache in ipv4.
We need a place to have long-term storage of PMTU/redirect information
which is independent of the routes themselves, yet does not get us
back into a situation where we have to write to metrics or anything
like that.
For this we use an "next-hop exception" table in the FIB nexthops.
The one thing I desperately want to avoid is having to create clone
routes in the FIB trie for this purpose, because that is very
expensive. However, I'm willing to entertain such an idea later
if this current scheme proves to have downsides that the FIB trie
variant would not have.
In order to accomodate this any such scheme, we need to be able to
produce a full flow key at PMTU/redirect time. That required an
adjustment of the interface call-sites used to propagate these events.
For a PMTU/redirect with a fully specified socket, we pass that socket
and use it to produce the flow key.
Otherwise we use a passed in SKB to formulate the key. There are two
cases that need to be distinguished, ICMP message processing (in which
case the IP header is at skb->data) and output packet processing
(mostly tunnels, and in all such cases the IP header is at ip_hdr(skb)).
We also have to make the code able to handle the case where the dst
itself passed into the dst_ops->{update_pmtu,redirect} method is
invalidated. This matters for calls from sockets that have cached
that route. We provide a inet{,6} helper function for this purpose,
and edit SCTP specially since it caches routes at the transport rather
than socket level.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 17 Jul 2012 05:22:36 +0000 (05:22 +0000)]
team: add netpoll support
It's done in very similar way this is done in bonding and bridge.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 17 Jul 2012 05:22:35 +0000 (05:22 +0000)]
netpoll: move np->dev and np->dev_name init into __netpoll_setup()
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jul 2012 11:19:00 +0000 (04:19 -0700)]
ipv4: Add FIB nexthop exceptions.
In a regime where we have subnetted route entries, we need a way to
store persistent storage about destination specific learned values
such as redirects and PMTU values.
This is implemented here via nexthop exceptions.
The initial implementation is a 2048 entry hash table with relaiming
starting at chain length 5. A more sophisticated scheme can be
devised if that proves necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Jul 2012 16:31:04 +0000 (17:31 +0100)]
sfc: Correct some comments on enum reset_type
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Wed, 4 Jul 2012 21:25:07 +0000 (22:25 +0100)]
sfc: Fix interface statistics running backward
Some interface statistics are computed in such a way that they can
sometimes decrease (and even underflow). Since the computed value
will never be greater than the true value, we fix this by only storing
the computed value when it increases.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Wed, 4 Jul 2012 02:58:33 +0000 (03:58 +0100)]
sfc: Disable VF queues during register self-test
Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.
On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again. So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.
In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting. Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Mon, 2 Jul 2012 22:37:40 +0000 (23:37 +0100)]
sfc: Explain why efx_mcdi_exit_assertion() ignores result of efx_mcdi_rpc()
Fix CID 113952 in Coverity report on Linux.
This is the one instance where we don't, and shouldn't, check the
return code from efx_mcdi_rpc(). It wasn't immediately obvious to me
why we didn't, so I think an explanation is in order.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Mon, 2 Jul 2012 22:03:02 +0000 (23:03 +0100)]
sfc: Use dev_kfree_skb() in efx_end_loopback()
Fix CID 102619 in the Coverity report on Linux.
efx_end_loopback() iterates over an array of skb pointers of which
some may be null (if efx_begin_loopback() failed). It should not use
dev_kfree_skb_irq(), which requires non-null pointers. In practice
this is safe because it does not run in interrupt context and
therefore always ends up calling dev_kfree_skb(), which does allow
null pointers. But we should make that explicit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Mon, 2 Jul 2012 20:36:59 +0000 (21:36 +0100)]
sfc: Use strlcpy() to copy ethtool stats names
Fix CID 113703 in the Coverity report on Linux.
ethtool stats names are limited to 32 bytes including a null
terminator. Use strlcpy() to ensure that we will always include the
null terminator even if a source string becomes longer than this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 28 Jun 2012 20:55:15 +0000 (21:55 +0100)]
sfc: Stop changing header offsets on TX
There is nothing in the VLAN driver or core VLAN support that
invalidates the TCP and IP header offsets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 19 Jun 2012 18:57:22 +0000 (19:57 +0100)]
sfc: Remove dead write to tso_state::packet_space
tso_state::packet_space is always set in tso_start_packet(); the
value set in tso_start() is not used, and is also incorrect.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 17 May 2012 16:46:55 +0000 (17:46 +0100)]
sfc: Use generic DMA API, not PCI-DMA API
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 31 May 2012 23:56:22 +0000 (00:56 +0100)]
sfc: Work around bogus 'uninitialised variable' warning
With some gcc versions & optimisations, the compiler will warn that
'depth' in efx_filter_insert_filter() may be used without being
initialised, although this is not the case.
This is related to inlining of efx_filter_search(), which only has
one caller since commit
8db182f4a8a6e2dcb8b65905ea4af56210e65430
('sfc: Remove now-unused filter function').
Shut the compiler up by initialising it to 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Eric Dumazet [Tue, 17 Jul 2012 01:41:30 +0000 (01:41 +0000)]
tcp: implement RFC 5961 4.2
Implement the RFC 5691 mitigation against Blind
Reset attack using SYN bit.
Section 4.2 of RFC 5961 advises to send a Challenge ACK and drop
incoming packet, instead of resetting the session.
Add a new SNMP counter to count number of challenge acks sent
in response to SYN packets.
(netstat -s | grep TCPSYNChallenge)
Remove obsolete TCPAbortOnSyn, since we no longer abort a TCP session
because of a SYN flag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kiran Kumar Kella <kkiran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jul 2012 10:29:28 +0000 (03:29 -0700)]
net: Pass optional SKB and SK arguments to dst_ops->{update_pmtu,redirect}()
This will be used so that we can compose a full flow key.
Even though we have a route in this context, we need more. In the
future the routes will be without destination address, source address,
etc. keying. One ipv4 route will cover entire subnets, etc.
In this environment we have to have a way to possess persistent storage
for redirects and PMTU information. This persistent storage will exist
in the FIB tables, and that's why we'll need to be able to rebuild a
full lookup flow key here. Using that flow key will do a fib_lookup()
and create/update the persistent entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 11 May 2012 08:32:55 +0000 (08:32 +0000)]
ixgbevf: Use igb style interrupt masks instead of ixgbe style
The interrupt registers accessed in ixgbevf are more similar to the igb
style registers than they are to the ixgbe style registers. As such we
would be better off setting up the code for the EICS, EIMS, EICS, EIAM, and
EIAC like we do in igb instead of ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 11 May 2012 08:32:50 +0000 (08:32 +0000)]
ixgbevf: Move Tx clean-up into NAPI context
Currently the VF driver is processing all of the transmits in interrupt
context. This can be messy since the Rx is all handled in NAPI and this
may result in interrupts being disabled. In order to resolve this move all
of the Tx packet processing into NAPI and combine all of the interrupt and
polling routines into just a pair of functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 11 May 2012 08:32:45 +0000 (08:32 +0000)]
ixgbevf: Update q_vector to contain ring pointers instead of bitmaps
For most cases the ixgbevf driver will only ever contain a single Tx and
single Rx queue. In order to track that it makes more sense to use a
pointer instead of using a bitmap which must be search in order to locate
the ring on an adapter index. As such I am changing the code to use
pointers and an iterator to access all rings on a given q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 11 May 2012 08:32:40 +0000 (08:32 +0000)]
ixgbevf: Cleanup accounting for space needed at start of xmit_frame
This change cleans up the accounting needed at the start of xmit_frame so
that we can avoid doing too much work to determine how many descriptors we
will need.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 11 May 2012 08:32:34 +0000 (08:32 +0000)]
ixgbevf: Drop use of eitr_low and eitr_high for hard coded values
This patch drops the use of eitr_low and eitr_high as values being stored
in the adapter structure. Since the values have no external way to be
changed they might as well just be hard coded values and save us the space
on the adapter structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 11 May 2012 08:32:29 +0000 (08:32 +0000)]
ixgbevf: Make use of NETIF_F_RXCSUM instead of keeping our own flag
The IXGBE_FLAG_RX_CSUM_ENABLED flag is redundant since NETIF_F_RXCSUM is
keeping the value we want to already have. As such we can drop the
redundant flag and just make use of NETIF_F_RXCSUM.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 11 May 2012 08:32:24 +0000 (08:32 +0000)]
ixgbevf: Drop netdev_registered value since that is already stored in netdev
There is no need to keep a separate netdev_registered value since that is
already stored in the netdev itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 11 May 2012 08:32:19 +0000 (08:32 +0000)]
ixgbevf: Drop all dead or unnecessary code
There is a large amount of code present in this driver to support features
that either do no exist or are not supported such ask packet split, DCA, or
RSC. This patch strips out almost all of that code and in the case of
conditionals based on unused flags I am flatting the code out to just the
path that would have been selected.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Tue, 17 Jul 2012 08:13:05 +0000 (10:13 +0200)]
tcp: implement RFC 5961 3.2
Implement the RFC 5691 mitigation against Blind
Reset attack using RST bit.
Idea is to validate incoming RST sequence,
to match RCV.NXT value, instead of previouly accepted
window : (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND)
If sequence is in window but not an exact match, send
a "challenge ACK", so that the other part can resend an
RST with the appropriate sequence.
Add a new sysctl, tcp_challenge_ack_limit, to limit
number of challenge ACK sent per second.
Add a new SNMP counter to count number of challenge acks sent.
(netstat -s | grep TCPChallengeACK)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kiran Kumar Kella <kkiran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Wei [Tue, 17 Jul 2012 07:28:59 +0000 (15:28 +0800)]
ipv6: fix unappropriate errno returned for non-multicast address
We need to check the passed in multicast address and return
appropriate errno(EINVAL) if it is not valid. And it's no need
to walk through the ipv6_mc_list in this situation.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jul 2012 08:34:11 +0000 (01:34 -0700)]
Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
the fifth pull request for upcoming v3.6 net-next. The first two
patches (created by me) add const qualifiers to the flexcan and
mpc5xxx_can driver. The next patch by Julia Lawall fixes a return value
problem in the error path of the softing driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Mon, 25 Jun 2012 22:32:50 +0000 (22:32 +0000)]
bnx2x: organize BDs calculation for stop/resume
Put the numbers used for stop/resume queue in a single place and
fix the condition for sanity check.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sat, 14 Jul 2012 16:43:04 +0000 (18:43 +0200)]
can: softing: softing_main: ensure a consistent return value in error case
Typically, the return value desired for the failure of a function with an
integer return value is a negative integer. In these cases, the return
value is sometimes a negative integer and sometimes 0, due to a subsequent
initialization of the return variable within the loop.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
//<smpl>
@r exists@
identifier ret;
position p;
constant C;
expression e1,e3,e4;
statement S;
@@
ret = -C
... when != ret = e3
when any
if@p (...) S
... when any
if (\(ret != 0\|ret < 0\|ret > 0\) || ...) { ... return ...; }
... when != ret = e3
when any
*if@p (...)
{
... when != ret = e4
return ret;
}
//</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 13 Jul 2012 12:54:59 +0000 (14:54 +0200)]
can: mpc5xxx_can: make data in mpc5xxx_can_probe const
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 13 Jul 2012 12:52:48 +0000 (14:52 +0200)]
can: flexcan: make flexcan_priv.devtype_data member point to const data
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Christian Riesch [Fri, 13 Jul 2012 05:26:31 +0000 (05:26 +0000)]
asix: Add a new driver for the AX88172A
The Asix AX88172A is a USB 2.0 Ethernet interface that supports both an
internal PHY as well as an external PHY (connected via MII).
This patch adds a driver for the AX88172A and provides support for
both modes and the phylib.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Riesch [Fri, 13 Jul 2012 05:26:30 +0000 (05:26 +0000)]
asix: Factor out common code
Allow the new driver for the AX88172A to share code with the
existing drivers for ASIX devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Riesch [Fri, 13 Jul 2012 05:26:29 +0000 (05:26 +0000)]
asix: Rename asix.c to asix_devices.c
This patch further creates two additional copies of asix.c.
In another patch these copies will be used to factor out
common code.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Bolle [Sat, 14 Jul 2012 23:11:55 +0000 (23:11 +0000)]
gigaset: silence GCC warning for unused 'format_ie'
Building Gigaset's CAPI support without Gigaset's debugging enabled
triggers this GCC warning:
'format_ie' defined but not used [-Wunused-function]
Silence this warning by wrapping format_ie() in an "#ifdef
CONFIG_GIGASET_DEBUG" and "#endif" pair.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Valentin Ilie [Sat, 14 Jul 2012 13:08:29 +0000 (13:08 +0000)]
drivers: connector: fixed coding style issues
V2: Replaced assignment in if statement.
Fixed coding style issues.
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masanari Iida [Fri, 13 Jul 2012 07:22:47 +0000 (07:22 +0000)]
irda: Fix typo in irda
Correct spelling typo in irda.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioan Orghici [Fri, 13 Jul 2012 07:16:37 +0000 (07:16 +0000)]
sctp: fix sparse warning for sctp_init_cause_fixed
Fix the following sparse warning:
* symbol 'sctp_init_cause_fixed' was not declared. Should it be
static?
Signed-off-by: Ioan Orghici <ioanorghici@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 16 Jul 2012 14:25:56 +0000 (14:25 +0000)]
bnx2: Try to recover from PCI block reset
If the PCI block has reset, the memory enable bit will be reset and
the device will not respond to MMIO access. bnx2_reset_task() currently
will not recover when this happens. Add code to detect this condition
and restore the PCI state. This scenario has been reported by some
users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 16 Jul 2012 16:24:02 +0000 (16:24 +0000)]
tg3: Add hwmon support for temperature
Some tg3 devices have management firmware that can export sensor data.
Export temperature sensor reading via hwmon sysfs.
[hwmon interface suggested by Ben Hutchings <bhutchings@solarflare.com>]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 16 Jul 2012 16:24:01 +0000 (16:24 +0000)]
tg3: Add APE scratchpad read function
for retreiving temperature sensor data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 16 Jul 2012 16:24:00 +0000 (16:24 +0000)]
tg3: Add common function tg3_ape_event_lock()
by refactoring code in tg3_ape_send_event(). The common function will
be used in subsequent patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 16 Jul 2012 16:23:59 +0000 (16:23 +0000)]
tg3: Fix the setting of the APE_HAS_NCSI flag
The driver currently skips setting this flag if the VPD contains the
firmware version string. We fix this by separating the probing of NCSI
from the reading of the NCSI version string. The APE_HAS_NCSI flag is
needed to properly read sensor data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 14 Jul 2012 03:16:27 +0000 (03:16 +0000)]
netem: refine early skb orphaning
netem does an early orphaning of skbs. Doing so breaks TCP Small Queue
or any mechanism relying on socket sk_wmem_alloc feedback.
Ideally, we should perform this orphaning after the rate module and
before the delay module, to mimic what happens on a real link :
skb orphaning is indeed normally done at TX completion, before the
transit on the link.
+-------+ +--------+ +---------------+ +-----------------+
+ Qdisc +---> Device +--> TX completion +--> links / hops +->
+ + + xmit + + skb orphaning + + propagation +
+-------+ +--------+ +---------------+ +-----------------+
< rate limiting > < delay, drops, reorders >
If netem is used without delay feature (drops, reorders, rate
limiting), then we should avoid early skb orphaning, to keep pressure
on sockets as long as packets are still in qdisc queue.
Ideally, netem should be refactored to implement delay module
as the last stage. Current algorithm merges the two phases
(rate limiting + delay) so its not correct.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Mark Gordon <msg@google.com>
Cc: Andreas Terzis <aterzis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jul 2012 06:04:00 +0000 (23:04 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next
Jett Kirsher says:
====================
This series contains updates to e1000e and ixgbe.
...
Alexander Duyck (5):
ixgbe: Simplify logic for getting traffic class from user priority
ixgbe: Cleanup unpacking code for DCB
ixgbe: Populate the prio_tc_map in ixgbe_setup_tc
ixgbe: Add function for obtaining FCoE TC based on FCoE user priority
ixgbe: Merge FCoE set_num and cache_ring calls into RSS/DCB config
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 13 Jul 2012 03:19:41 +0000 (03:19 +0000)]
be2net: dont pull too much data in skb linear part
skb_fill_rx_data() pulls 64 byte of data in skb->data
Its too much for TCP (with no options) on IPv4, as total size of headers
is 14 + 40 = 54
This means tcp stack and splice() are suboptimal, since tcp payload
is in part in tcp->data, and in part in skb frag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Padmanabh Ratnakar [Fri, 13 Jul 2012 02:46:03 +0000 (02:46 +0000)]
be2net: update driver version
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Padmanabh Ratnakar [Fri, 13 Jul 2012 02:45:51 +0000 (02:45 +0000)]
be2net: Add description about various RSS hash types
Incorporated review comment from Eric Dumazet. Added description
about different RSS hash types which adapter is capable of.
Will add support for ETHTOOL_GRXFH and ETHTOOL_SRXFX as suggested
by Ben Hutchings in a later patch.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Tue, 10 Jul 2012 22:29:19 +0000 (22:29 +0000)]
bridge: Fix enforcement of multicast hash_max limit
The hash size is doubled when it needs to grow and compared against
hash_max. The >= comparison will limit the hash table size to half
of what is expected i.e. the default 512 hash_max will not allow
the hash table to grow larger than 256.
Also print the hash table limit instead of the desirable size when
the limit is reached.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 10 Jul 2012 20:34:07 +0000 (20:34 +0000)]
net/mlx4_en: dereferencing freed memory
We dereferenced "mclist" after the kfree().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 10 Jul 2012 20:33:36 +0000 (20:33 +0000)]
net/mlx4: off by one in parse_trans_rule()
This should be ">=" here instead of ">". MLX4_NET_TRANS_RULE_NUM is 6.
We use "spec->id" as an array offset into the __rule_hw_sz[] and
__sw_id_hw[] arrays which have 6 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Ovsienko [Tue, 10 Jul 2012 04:45:50 +0000 (04:45 +0000)]
ipv6: fix RTPROT_RA markup of RA routes w/nexthops
Userspace implementations of network routing protocols sometimes need to
tell RA-originated IPv6 routes from other kernel routes to make proper
routing decisions. This makes most sense for RA routes with nexthops,
namely, default routes and Route Information routes.
The intended mean of preserving RA route origin in a netlink message is
through indicating RTPROT_RA as protocol code. Function rt6_fill_node()
tried to do that for default routes, but its test condition was taken
wrong. This change is modeled after the original mailing list posting
by Jeff Haran. It fixes the test condition for default route case and
sets the same behaviour for Route Information case (both types use
nexthops). Handling of the 3rd RA route type, Prefix Information, is
left unchanged, as it stands for interface connected routes (without
nexthops).
Signed-off-by: Denis Ovsienko <infrastation@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 10 Jul 2012 07:19:22 +0000 (07:19 +0000)]
hyperv: Add support for setting MAC from within guests
This adds support for setting synthetic NIC MAC address from within Linux
guests. Before using this feature, the option "spoofing of MAC address"
should be enabled at the Hyper-V manager / Settings of the synthetic
NIC.
Thanks to Kin Cho <kcho@infoblox.com> for the initial implementation and
tests. And, thanks to Long Li <longli@microsoft.com> for the debugging
works.
Reported-and-tested-by: Kin Cho <kcho@infoblox.com>
Reported-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Cheneau [Wed, 11 Jul 2012 06:51:16 +0000 (06:51 +0000)]
6lowpan: Change byte order when storing/accessing to len field
Lenght field should be encoded using big endian byte order, such as intend in the specs.
As it is currently written, the len field would not be decoded properly on an implementation using the correct byte ordering. Hence, it could lead to interroperability issues.
Also, I rewrote the code so that iphc0 argument of lowpan_alloc_new_frame could be removed.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Cheneau [Wed, 11 Jul 2012 06:51:15 +0000 (06:51 +0000)]
6lowpan: Change byte order when storing/accessing u16 tag
The tag field should be stored and accessed using big endian byte order (as
intended in the specs). Or else, when displayed with a trafic analyser, such a
Wireshark, the field not properly displayed (e.g. 0x01 00 instead of 0x00 01,
and so on).
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Cheneau [Wed, 11 Jul 2012 06:51:14 +0000 (06:51 +0000)]
6lowpan: Fix null pointer dereference in UDP uncompression function
When a UDP packet gets fragmented, a crash will occur at reassembly time.
This is because skb->transport_header is not set during earlier period of fragment reassembly.
As a consequence, call to udp_hdr() return NULL and uh (which is NULL) gets
dereferenced without much test.
Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Fri, 13 Jul 2012 05:33:12 +0000 (22:33 -0700)]
arch: Use eth_random_addr
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Fri, 13 Jul 2012 05:33:11 +0000 (22:33 -0700)]
usb: Use eth_random_addr
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Fri, 13 Jul 2012 05:33:10 +0000 (22:33 -0700)]
s390: Use eth_random_addr
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 12 Jul 2012 19:33:09 +0000 (19:33 +0000)]
drivers/net: Use eth_random_addr
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 12 Jul 2012 19:33:08 +0000 (19:33 +0000)]
wireless: Use eth_random_addr
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 12 Jul 2012 19:33:07 +0000 (19:33 +0000)]
net: usb: Use eth_random_addr
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 12 Jul 2012 19:33:06 +0000 (19:33 +0000)]
ethernet: Use eth_random_addr
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 12 Jul 2012 19:33:05 +0000 (19:33 +0000)]
etherdevice: Rename random_ether_addr to eth_random_addr
Add some API symmetry to eth_broadcast_addr and
add a #define to the old name for backward compatibility.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jul 2012 05:33:32 +0000 (22:33 -0700)]
Merge branch 'tipc_net-next' of git://git./linux/kernel/git/paulg/linux
Paul Gortmaker says:
====================
This is the same eight commits as sent for review last week[1],
with just the incorporation of the pr_fmt change as suggested
by JoeP. There was no additional change requests, so unless you
can see something else you'd like me to change, please pull.
...
Erik Hugne (5):
tipc: use standard printk shortcut macros (pr_err etc.)
tipc: remove TIPC packet debugging functions and macros
tipc: simplify print buffer handling in tipc_printf
tipc: phase out most of the struct print_buf usage
tipc: remove print_buf and deprecated log buffer code
Paul Gortmaker (3):
tipc: factor stats struct out of the larger link struct
tipc: limit error messages relating to memory leak to one line
tipc: simplify link_print by divorcing it from using tipc_printf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Vagin [Mon, 16 Jul 2012 04:28:49 +0000 (04:28 +0000)]
net: make sock diag per-namespace
Before this patch sock_diag works for init_net only and dumps
information about sockets from all namespaces.
This patch expands sock_diag for all name-spaces.
It creates a netlink kernel socket for each netns and filters
data during dumping.
v2: filter accoding with netns in all places
remove an unused variable.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pavel Emelyanov <xemul@parallels.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duan Jiong [Mon, 16 Jul 2012 02:29:05 +0000 (02:29 +0000)]
lpc_eth: remove duplicated include
Remove duplicated #include <linux/delay.h> in
drivers/net/ethernet/nxp/lpc_eth.c
Signed-off-by: Duan Jiong<djduanjiong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 16 Jul 2012 01:41:36 +0000 (01:41 +0000)]
tcp: add OFO snmp counters
Add three SNMP TCP counters, to better track TCP behavior
at global stage (netstat -s), when packets are received
Out Of Order (OFO)
TCPOFOQueue : Number of packets queued in OFO queue
TCPOFODrop : Number of packets meant to be queued in OFO
but dropped because socket rcvbuf limit hit.
TCPOFOMerge : Number of packets in OFO that were merged with
other packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Jul 2012 10:57:14 +0000 (03:57 -0700)]
sctp: Adjust PMTU updates to accomodate route invalidation.
This adjusts the call to dst_ops->update_pmtu() so that we can
transparently handle the fact that, in the future, the dst itself can
be invalidated by the PMTU update (when we have non-host routes cached
in sockets).
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Jul 2012 10:44:56 +0000 (03:44 -0700)]
ipv6: Add helper inet6_csk_update_pmtu().
This is the ipv6 version of inet_csk_update_pmtu().
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Jul 2012 10:28:06 +0000 (03:28 -0700)]
ipv4: Add helper inet_csk_update_pmtu().
This abstracts away the call to dst_ops->update_pmtu() so that we can
transparently handle the fact that, in the future, the dst itself can
be invalidated by the PMTU update (when we have non-host routes cached
in sockets).
So we try to rebuild the socket cached route after the method
invocation if necessary.
This isn't used by SCTP because it needs to cache dsts per-transport,
and thus will need it's own local version of this helper.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 30 Jun 2012 00:14:01 +0000 (00:14 +0000)]
ixgbe: Merge FCoE set_num and cache_ring calls into RSS/DCB config
This change merges the ixgbe_cache_ring_fcoe and ixgbe_set_fcoe_queues
logic into the DCB and RSS initialization calls.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Sat, 2 Jun 2012 00:11:02 +0000 (00:11 +0000)]
ixgbe: Add function for obtaining FCoE TC based on FCoE user priority
In upcoming patches it will become increasingly common to need to determine
the FCoE traffic class in order to determine the correct queues for FCoE.
In order to make this easier I am adding a function for obtaining the FCoE
traffic class based on the user priority.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 18 May 2012 06:33:31 +0000 (06:33 +0000)]
ixgbe: Populate the prio_tc_map in ixgbe_setup_tc
There were cases where the prio_tc_map was not populated when we were
calling open. This will result in us incorrectly configuring the traffic
classes when DCB is enabled. In order to correct this I have updated the
code so that we now populate the values prior to allocating the q_vectors
and calling ixgbe_open.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 17 May 2012 05:14:39 +0000 (05:14 +0000)]
ixgbe: Cleanup unpacking code for DCB
This is meant to be a generic clean-up of the remaining functions for
unpacking data from the DCB structures. The only real changes are:
replaced the variable i with tc for functions that were looping through the
traffic classes, and added a pointer for tc_class instead of path since
that way we only need to pull the pointer once instead of once per loop.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 17 May 2012 05:14:34 +0000 (05:14 +0000)]
ixgbe: Simplify logic for getting traffic class from user priority
This patch is meant to help simplify the logic for getting traffic classes
from user priorities. To do this I am adding a function named
ixgbe_dcb_get_tc_from_up that will go through the traffic classes in
reverse order in order to determine which traffic class contains a bit for
a given user priority.
Adding a declaration for this new function to the header so that
we have a centralized means for sorting out traffic classes belonging to
features such as FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Thu, 12 Jul 2012 00:02:42 +0000 (00:02 +0000)]
e1000e: Program the correct register for ITR when using MSI-X.
When configuring interrupt throttling on 82574 in MSI-X mode, we need to
be programming the EITR registers instead of the ITR register.
-rc2: Renamed e1000_write_itr() to e1000e_write_itr(), fixed whitespace
issues, and removed unnecessary !! operation.
-rc3: Reduced the scope of the loop variable in e1000e_write_itr().
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tushar Dave [Thu, 12 Jul 2012 08:00:15 +0000 (08:00 +0000)]
e1000e: Cleanup code logic in e1000_check_for_serdes_link_82571()
Cleanup code to make it more clean and readable.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>