OSDN Git Service
Andrew Elble [Thu, 9 Nov 2017 18:41:10 +0000 (13:41 -0500)]
nfsd: check for use of the closed special stateid
[ Upstream commit
ae254dac721d44c0bfebe2795df87459e2e88219 ]
Prevent the use of the closed (invalid) special stateid by clients.
Signed-off-by: Andrew Elble <aweits@rit.edu>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vasily Averin [Mon, 6 Nov 2017 13:22:48 +0000 (16:22 +0300)]
grace: replace BUG_ON by WARN_ONCE in exit_net hook
[ Upstream commit
b872285751c1af010e12d02bce7069e2061a58ca ]
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Fri, 3 Nov 2017 12:00:15 +0000 (08:00 -0400)]
nfsd: Ensure we check stateid validity in the seqid operation checks
[ Upstream commit
9271d7e509c1bfc0b9a418caec29ec8d1ac38270 ]
After taking the stateid st_mutex, we want to know that the stateid
still represents valid state before performing any non-idempotent
actions.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Fri, 3 Nov 2017 12:00:12 +0000 (08:00 -0400)]
nfsd: CLOSE SHOULD return the invalid special stateid for NFSv4.x (x>0)
[ Upstream commit
fb500a7cfee7f2f447d2bbf30cb59629feab6ac1 ]
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eduardo Otubo [Thu, 23 Nov 2017 14:18:35 +0000 (15:18 +0100)]
xen-netfront: remove warning when unloading module
[ Upstream commit
5b5971df3bc2775107ddad164018a8a8db633b81 ]
v2:
* Replace busy wait with wait_event()/wake_up_all()
* Cannot garantee that at the time xennet_remove is called, the
xen_netback state will not be XenbusStateClosed, so added a
condition for that
* There's a small chance for the xen_netback state is
XenbusStateUnknown by the time the xen_netfront switches to Closed,
so added a condition for that.
When unloading module xen_netfront from guest, dmesg would output
warning messages like below:
[ 105.236836] xen:grant_table: WARNING: g.e. 0x903 still in use!
[ 105.236839] deferring g.e. 0x903 (pfn 0x35805)
This problem relies on netfront and netback being out of sync. By the time
netfront revokes the g.e.'s netback didn't have enough time to free all of
them, hence displaying the warnings on dmesg.
The trick here is to make netfront to wait until netback frees all the g.e.'s
and only then continue to cleanup for the module removal, and this is done by
manipulating both device states.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wanpeng Li [Mon, 20 Nov 2017 22:52:21 +0000 (14:52 -0800)]
KVM: VMX: Fix rflags cache during vCPU reset
[ Upstream commit
c37c28730bb031cc8a44a130c2555c0f3efbe2d0 ]
Reported by syzkaller:
*** Guest State ***
CR0: actual=0x0000000080010031, shadow=0x0000000060000010, gh_mask=
fffffffffffffff7
CR4: actual=0x0000000000002061, shadow=0x0000000000000000, gh_mask=
ffffffffffffe8f1
CR3 = 0x000000002081e000
RSP = 0x000000000000fffa RIP = 0x0000000000000000
RFLAGS=0x00023000 DR7 = 0x00000000000000
^^^^^^^^^^
------------[ cut here ]------------
WARNING: CPU: 6 PID: 24431 at /home/kernel/linux/arch/x86/kvm//x86.c:7302 kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm]
CPU: 6 PID: 24431 Comm: reprotest Tainted: G W OE 4.14.0+ #26
RIP: 0010:kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm]
RSP: 0018:
ffff880291d179e0 EFLAGS:
00010202
Call Trace:
kvm_vcpu_ioctl+0x479/0x880 [kvm]
do_vfs_ioctl+0x142/0x9a0
SyS_ioctl+0x74/0x80
entry_SYSCALL_64_fastpath+0x23/0x9a
The failed vmentry is triggered by the following beautified testcase:
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <linux/kvm.h>
#include <fcntl.h>
#include <sys/ioctl.h>
long r[5];
int main()
{
struct kvm_debugregs dr = { 0 };
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7);
struct kvm_guest_debug debug = {
.control = 0xf0403,
.arch = {
.debugreg[6] = 0x2,
.debugreg[7] = 0x2
}
};
ioctl(r[4], KVM_SET_GUEST_DEBUG, &debug);
ioctl(r[4], KVM_RUN, 0);
}
which testcase tries to setup the processor specific debug
registers and configure vCPU for handling guest debug events through
KVM_SET_GUEST_DEBUG. The KVM_SET_GUEST_DEBUG ioctl will get and set
rflags in order to set TF bit if single step is needed. All regs' caches
are reset to avail and GUEST_RFLAGS vmcs field is reset to 0x2 during vCPU
reset. However, the cache of rflags is not reset during vCPU reset. The
function vmx_get_rflags() returns an unreset rflags cache value since
the cache is marked avail, it is 0 after boot. Vmentry fails if the
rflags reserved bit 1 is 0.
This patch fixes it by resetting both the GUEST_RFLAGS vmcs field and
its cache to 0x2 during vCPU reset.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Wed, 15 Nov 2017 21:20:52 +0000 (16:20 -0500)]
btrfs: fix deadlock when writing out space cache
[ Upstream commit
b77000ed558daa3bef0899d29bf171b8c9b5e6a8 ]
If we fail to prepare our pages for whatever reason (out of memory in
our case) we need to make sure to drop the block_group->data_rwsem,
otherwise hilarity ensues.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add label and use existing unlocking code ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chun-Yeow Yeoh [Tue, 14 Nov 2017 15:20:05 +0000 (23:20 +0800)]
mac80211: fix the update of path metric for RANN frame
[ Upstream commit
fbbdad5edf0bb59786a51b94a9d006bc8c2da9a2 ]
The previous path metric update from RANN frame has not considered
the own link metric toward the transmitting mesh STA. Fix this.
Reported-by: Michael65535
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zhangliping [Sat, 25 Nov 2017 14:02:12 +0000 (22:02 +0800)]
openvswitch: fix the incorrect flow action alloc size
[ Upstream commit
67c8d22a73128ff910e2287567132530abcf5b71 ]
If we want to add a datapath flow, which has more than 500 vxlan outputs'
action, we will get the following error reports:
openvswitch: netlink: Flow action size 32832 bytes exceeds max
openvswitch: netlink: Flow action size 32832 bytes exceeds max
openvswitch: netlink: Actions may not be safe on all matching packets
... ...
It seems that we can simply enlarge the MAX_ACTIONS_BUFSIZE to fix it, but
this is not the root cause. For example, for a vxlan output action, we need
about 60 bytes for the nlattr, but after it is converted to the flow
action, it only occupies 24 bytes. This means that we can still support
more than 1000 vxlan output actions for a single datapath flow under the
the current 32k max limitation.
So even if the nla_len(attr) is larger than MAX_ACTIONS_BUFSIZE, we
shouldn't report EINVAL and keep it move on, as the judgement can be
done by the reserve_sfa_size.
Signed-off-by: zhangliping <zhangliping02@baidu.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Kuehling [Wed, 1 Nov 2017 23:21:57 +0000 (19:21 -0400)]
drm/amdkfd: Fix SDMA oversubsription handling
[ Upstream commit
8c946b8988acec785bcf67088b6bd0747f36d2d3 ]
SDMA only supports a fixed number of queues. HWS cannot handle
oversubscription.
Signed-off-by: shaoyun liu <shaoyun.liu@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
shaoyunl [Wed, 1 Nov 2017 23:21:56 +0000 (19:21 -0400)]
drm/amdkfd: Fix SDMA ring buffer size calculation
[ Upstream commit
d12fb13f23199faa7e536acec1db49068e5a067d ]
ffs function return the position of the first bit set on 1 based.
(bit zero returns 1).
Signed-off-by: shaoyun liu <shaoyun.liu@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Kuehling [Wed, 1 Nov 2017 23:21:55 +0000 (19:21 -0400)]
drm/amdgpu: Fix SDMA load/unload sequence on HWS disabled mode
[ Upstream commit
cf21654b40968609779751b34e7923180968fe5b ]
Fix the SDMA load and unload sequence as suggested by HW document.
Signed-off-by: shaoyun liu <shaoyun.liu@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Lyle [Fri, 24 Nov 2017 23:14:27 +0000 (15:14 -0800)]
bcache: check return value of register_shrinker
[ Upstream commit
6c4ca1e36cdc1a0a7a84797804b87920ccbebf51 ]
register_shrinker is now __must_check, so check it to kill a warning.
Caller of bch_btree_cache_alloc in super.c appropriately checks return
value so this is fully plumbed through.
This V2 fixes checkpatch warnings and improves the commit description,
as I was too hasty getting the previous version out.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Vojtech Pavlik <vojtech@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Hogan [Wed, 15 Nov 2017 21:17:55 +0000 (21:17 +0000)]
cpufreq: Add Loongson machine dependencies
[ Upstream commit
0d307935fefa6389eb726c6362351c162c949101 ]
The MIPS loongson cpufreq drivers don't build unless configured for the
correct machine type, due to dependency on machine specific architecture
headers and symbols in machine specific platform code.
More specifically loongson1-cpufreq.c uses RST_CPU_EN and RST_CPU,
neither of which is defined in asm/mach-loongson32/regs-clk.h unless
CONFIG_LOONGSON1_LS1B=y, and loongson2_cpufreq.c references
loongson2_clockmod_table[], which is only defined in
arch/mips/loongson64/lemote-2f/clock.c, i.e. when
CONFIG_LEMOTE_MACH2F=y.
Add these dependencies to Kconfig to avoid randconfig / allyesconfig
build failures (e.g. when based on BMIPS which also has a cpufreq
driver).
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Sun, 15 Oct 2017 19:24:49 +0000 (21:24 +0200)]
ACPI / bus: Leave modalias empty for devices which are not present
[ Upstream commit
10809bb976648ac58194a629e3d7af99e7400297 ]
Most Bay and Cherry Trail devices use a generic DSDT with all possible
peripheral devices present in the DSDT, with their _STA returning 0x00 or
0x0f based on AML variables which describe what is actually present on
the board.
Since ACPI device objects with a 0x00 status (not present) still get an
entry under /sys/bus/acpi/devices, and those entry had an acpi:PNPID
modalias, userspace would end up loading modules for non present hardware.
This commit fixes this by leaving the modalias empty for non present
devices. This results in 10 modules less being loaded with a generic
distro kernel config on my Cherry Trail test-device (a GPD pocket).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikita Leshenko [Sun, 5 Nov 2017 13:52:33 +0000 (15:52 +0200)]
KVM: x86: ioapic: Preserve read-only values in the redirection table
[ Upstream commit
b200dded0a6974a3b69599832b2203483920ab25 ]
According to
82093AA (IOAPIC) manual, Remote IRR and Delivery Status are
read-only. QEMU implements the bits as RO in commit
479c2a1cb7fb
("ioapic: keep RO bits for IOAPIC entry").
Signed-off-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikita Leshenko [Sun, 5 Nov 2017 13:52:32 +0000 (15:52 +0200)]
KVM: x86: ioapic: Clear Remote IRR when entry is switched to edge-triggered
[ Upstream commit
a8bfec2930525808c01f038825d1df3904638631 ]
Some OSes (Linux, Xen) use this behavior to clear the Remote IRR bit for
IOAPICs without an EOI register. They simulate the EOI message manually
by changing the trigger mode to edge and then back to level, with the
entry being masked during this.
QEMU implements this feature in commit
ed1263c363c9
("ioapic: clear remote irr bit for edge-triggered interrupts")
As a side effect, this commit removes an incorrect behavior where Remote
IRR was cleared when the redirection table entry was rewritten. This is not
consistent with the manual and also opens an opportunity for a strange
behavior when a redirection table entry is modified from an interrupt
handler that handles the same entry: The modification will clear the
Remote IRR bit even though the interrupt handler is still running.
Signed-off-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikita Leshenko [Sun, 5 Nov 2017 13:52:29 +0000 (15:52 +0200)]
KVM: x86: ioapic: Fix level-triggered EOI and IOAPIC reconfigure race
[ Upstream commit
0fc5a36dd6b345eb0d251a65c236e53bead3eef7 ]
KVM uses ioapic_handled_vectors to track vectors that need to notify the
IOAPIC on EOI. The problem is that IOAPIC can be reconfigured while an
interrupt with old configuration is pending or running and
ioapic_handled_vectors only remembers the newest configuration;
thus EOI from the old interrupt is not delievered to the IOAPIC.
A previous commit
db2bdcbbbd32
("KVM: x86: fix edge EOI and IOAPIC reconfig race")
addressed this issue by adding pending edge-triggered interrupts to
ioapic_handled_vectors, fixing this race for edge-triggered interrupts.
The commit explicitly ignored level-triggered interrupts,
but this race applies to them as well:
1) IOAPIC sends a level triggered interrupt vector to VCPU0
2) VCPU0's handler deasserts the irq line and reconfigures the IOAPIC
to route the vector to VCPU1. The reconfiguration rewrites only the
upper 32 bits of the IOREDTBLn register. (Causes KVM to update
ioapic_handled_vectors for VCPU0 and it no longer includes the vector.)
3) VCPU0 sends EOI for the vector, but it's not delievered to the
IOAPIC because the ioapic_handled_vectors doesn't include the vector.
4) New interrupts are not delievered to VCPU1 because remote_irr bit
is set forever.
Therefore, the correct behavior is to add all pending and running
interrupts to ioapic_handled_vectors.
This commit introduces a slight performance hit similar to
commit
db2bdcbbbd32 ("KVM: x86: fix edge EOI and IOAPIC reconfig race")
for the rare case that the vector is reused by a non-IOAPIC source on
VCPU0. We prefer to keep solution simple and not handle this case just
as the original commit does.
Fixes:
db2bdcbbbd32 ("KVM: x86: fix edge EOI and IOAPIC reconfig race")
Signed-off-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wanpeng Li [Mon, 6 Nov 2017 00:54:47 +0000 (16:54 -0800)]
KVM: X86: Fix operand/address-size during instruction decoding
[ Upstream commit
3853be2603191829b442b64dac6ae8ba0c027bf9 ]
Pedro reported:
During tests that we conducted on KVM, we noticed that executing a "PUSH %ES"
instruction under KVM produces different results on both memory and the SP
register depending on whether EPT support is enabled. With EPT the SP is
reduced by 4 bytes (and the written value is 0-padded) but without EPT support
it is only reduced by 2 bytes. The difference can be observed when the CS.DB
field is 1 (32-bit) but not when it's 0 (16-bit).
The internal segment descriptor cache exist even in real/vm8096 mode. The CS.D
also should be respected instead of just default operand/address-size/66H
prefix/67H prefix during instruction decoding. This patch fixes it by also
adjusting operand/address-size according to CS.D.
Reported-by: Pedro Fonseca <pfonseca@cs.washington.edu>
Tested-by: Pedro Fonseca <pfonseca@cs.washington.edu>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Pedro Fonseca <pfonseca@cs.washington.edu>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liran Alon [Sun, 5 Nov 2017 14:56:34 +0000 (16:56 +0200)]
KVM: x86: Don't re-execute instruction when not passing CR2 value
[ Upstream commit
9b8ae63798cb97e785a667ff27e43fa6220cb734 ]
In case of instruction-decode failure or emulation failure,
x86_emulate_instruction() will call reexecute_instruction() which will
attempt to use the cr2 value passed to x86_emulate_instruction().
However, when x86_emulate_instruction() is called from
emulate_instruction(), cr2 is not passed (passed as 0) and therefore
it doesn't make sense to execute reexecute_instruction() logic at all.
Fixes:
51d8b66199e9 ("KVM: cleanup emulate_instruction")
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liran Alon [Sun, 5 Nov 2017 14:56:33 +0000 (16:56 +0200)]
KVM: x86: emulator: Return to user-mode on L1 CPL=0 emulation failure
[ Upstream commit
1f4dcb3b213235e642088709a1c54964d23365e9 ]
On this case, handle_emulation_failure() fills kvm_run with
internal-error information which it expects to be delivered
to user-mode for further processing.
However, the code reports a wrong return-value which makes KVM to never
return to user-mode on this scenario.
Fixes:
6d77dbfc88e3 ("KVM: inject #UD if instruction emulation fails and exit to
userspace")
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lyude Paul [Tue, 12 Dec 2017 19:31:30 +0000 (14:31 -0500)]
igb: Free IRQs when device is hotplugged
commit
888f22931478a05bc81ceb7295c626e1292bf0ed upstream.
Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon
hotplugging my kernel would immediately crash due to igb:
[ 680.825801] kernel BUG at drivers/pci/msi.c:352!
[ 680.828388] invalid opcode: 0000 [#1] SMP
[ 680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb]
[ 680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G O 4.15.0-rc3Lyude-Test+ #6
[ 680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017
[ 680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn
[ 680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0
[ 680.833271] RSP: 0018:
ffffc9000030fbf0 EFLAGS:
00010286
[ 680.833761] RAX:
ffff8803405f9c00 RBX:
ffff88033e3d2e40 RCX:
000000000000002c
[ 680.834278] RDX:
0000000000000000 RSI:
00000000000000ac RDI:
ffff880340be2178
[ 680.834832] RBP:
0000000000000000 R08:
ffff880340be1ff0 R09:
ffff8803405f9c00
[ 680.835342] R10:
0000000000000000 R11:
0000000000000040 R12:
ffff88033d63a298
[ 680.835822] R13:
ffff88033d63a000 R14:
0000000000000060 R15:
ffff880341959000
[ 680.836332] FS:
0000000000000000(0000) GS:
ffff88034f440000(0000) knlGS:
0000000000000000
[ 680.836817] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 680.837360] CR2:
000055e64044afdf CR3:
0000000001c09002 CR4:
00000000003606e0
[ 680.837954] Call Trace:
[ 680.838853] pci_disable_msix+0xce/0xf0
[ 680.839616] igb_reset_interrupt_capability+0x5d/0x60 [igb]
[ 680.840278] igb_remove+0x9d/0x110 [igb]
[ 680.840764] pci_device_remove+0x36/0xb0
[ 680.841279] device_release_driver_internal+0x157/0x220
[ 680.841739] pci_stop_bus_device+0x7d/0xa0
[ 680.842255] pci_stop_bus_device+0x2b/0xa0
[ 680.842722] pci_stop_bus_device+0x3d/0xa0
[ 680.843189] pci_stop_and_remove_bus_device+0xe/0x20
[ 680.843627] trim_stale_devices+0xf3/0x140
[ 680.844086] trim_stale_devices+0x94/0x140
[ 680.844532] trim_stale_devices+0xa6/0x140
[ 680.845031] ? get_slot_status+0x90/0xc0
[ 680.845536] acpiphp_check_bridge.part.5+0xfe/0x140
[ 680.846021] acpiphp_hotplug_notify+0x175/0x200
[ 680.846581] ? free_bridge+0x100/0x100
[ 680.847113] acpi_device_hotplug+0x8a/0x490
[ 680.847535] acpi_hotplug_work_fn+0x1a/0x30
[ 680.848076] process_one_work+0x182/0x3a0
[ 680.848543] worker_thread+0x2e/0x380
[ 680.848963] ? process_one_work+0x3a0/0x3a0
[ 680.849373] kthread+0x111/0x130
[ 680.849776] ? kthread_create_worker_on_cpu+0x50/0x50
[ 680.850188] ret_from_fork+0x1f/0x30
[ 680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b
[ 680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP:
ffffc9000030fbf0
As it turns out, normally the freeing of IRQs that would fix this is called
inside of the scope of __igb_close(). However, since the device is
already gone by the point we try to unregister the netdevice from the
driver due to a hotplug we end up seeing that the netif isn't present
and thus, forget to free any of the device IRQs.
So: make sure that if we're in the process of dismantling the netdev, we
always allow __igb_close() to be called so that IRQs may be freed
normally. Additionally, only allow igb_close() to be called from
__igb_close() if it hasn't already been called for the given adapter.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes:
9474933caf21 ("igb: close/suspend race in netif_device_detach")
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesse Chan [Mon, 20 Nov 2017 20:57:13 +0000 (12:57 -0800)]
mtd: nand: denali_pci: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
commit
d822401d1c6898a4a4ee03977b78b8cec402e88a upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/mtd/nand/denali_pci.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesse Chan [Mon, 20 Nov 2017 20:54:26 +0000 (12:54 -0800)]
gpio: ath79: add missing MODULE_DESCRIPTION/LICENSE
commit
539340f37e6d6ed4cd93e8e18c9b2e4eafd4b842 upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/gpio/gpio-ath79.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION is also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesse Chan [Mon, 20 Nov 2017 20:54:52 +0000 (12:54 -0800)]
gpio: iop: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
commit
97b03136e1b637d7a9d2274c099e44ecf23f1103 upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/gpio/gpio-iop.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesse Chan [Mon, 20 Nov 2017 20:58:27 +0000 (12:58 -0800)]
power: reset: zx-reboot: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
commit
348c7cf5fcbcb68838255759d4cb45d039af36d2 upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/power/reset/zx-reboot.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephan Mueller [Tue, 2 Jan 2018 07:55:25 +0000 (08:55 +0100)]
crypto: af_alg - whitelist mask and type
commit
bb30b8848c85e18ca7e371d0a869e94b3e383bdf upstream.
The user space interface allows specifying the type and mask field used
to allocate the cipher. Only a subset of the possible flags are intended
for user space. Therefore, white-list the allowed flags.
In case the user space caller uses at least one non-allowed flag, EINVAL
is returned.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephan Mueller [Thu, 18 Jan 2018 19:41:09 +0000 (20:41 +0100)]
crypto: aesni - handle zero length dst buffer
commit
9c674e1e2f9e24fa4392167efe343749008338e0 upstream.
GCM can be invoked with a zero destination buffer. This is possible if
the AAD and the ciphertext have zero lengths and only the tag exists in
the source buffer (i.e. a source buffer cannot be zero). In this case,
the GCM cipher only performs the authentication and no decryption
operation.
When the destination buffer has zero length, it is possible that no page
is mapped to the SG pointing to the destination. In this case,
sg_page(req->dst) is an invalid access. Therefore, page accesses should
only be allowed if the req->dst->length is non-zero which is the
indicator that a page must exist.
This fixes a crash that can be triggered by user space via AF_ALG.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 9 Jan 2018 22:11:03 +0000 (23:11 +0100)]
ALSA: seq: Make ioctls race-free
commit
b3defb791b26ea0683a93a4f49c77ec45ec96f10 upstream.
The ALSA sequencer ioctls have no protection against racy calls while
the concurrent operations may lead to interfere with each other. As
reported recently, for example, the concurrent calls of setting client
pool with a combination of write calls may lead to either the
unkillable dead-lock or UAF.
As a slightly big hammer solution, this patch introduces the mutex to
make each ioctl exclusive. Although this may reduce performance via
parallel ioctl calls, usually it's not demanded for sequencer usages,
hence it should be negligible.
Reported-by: Luo Quan <a4651386@163.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 4.4: ioctl dispatch is done from snd_seq_do_ioctl();
take the mutex and add ret variable there.]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hugh Dickins [Tue, 30 Jan 2018 02:15:33 +0000 (18:15 -0800)]
kaiser: fix intel_bts perf crashes
Vince reported perf_fuzzer quickly locks up on 4.15-rc7 with PTI;
Robert reported Bad RIP with KPTI and Intel BTS also on 4.15-rc7:
honggfuzz -f /tmp/somedirectorywithatleastonefile \
--linux_perf_bts_edge -s -- /bin/true
(honggfuzz from https://github.com/google/honggfuzz) crashed with
BUG: unable to handle kernel paging request at
ffff9d3215100000
(then narrowed it down to
perf record --per-thread -e intel_bts//u -- /bin/ls).
The intel_bts driver does not use the 'normal' BTS buffer which is
exposed through kaiser_add_mapping(), but instead uses the memory
allocated for the perf AUX buffer.
This obviously comes apart when using PTI, because then the kernel
mapping, which includes that AUX buffer memory, disappears while
switched to user page tables.
Easily fixed in old-Kaiser backports, by applying kaiser_add_mapping()
to those pages; perhaps not so easy for upstream, where 4.15-rc8 commit
99a9dc98ba52 ("x86,perf: Disable intel_bts when PTI") disables for now.
Slightly reorganized surrounding code in bts_buffer_setup_aux(),
so it can better match bts_buffer_free_aux(): free_aux with an #ifdef
to avoid the loop when PTI is off, but setup_aux needs to loop anyway
(and kaiser_add_mapping() is cheap when PTI config is off or "pti=off").
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Reported-by: Robert Święcki <robert@swiecki.net>
Analyzed-by: Peter Zijlstra <peterz@infradead.org>
Analyzed-by: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Vince Weaver <vince@deater.net>
Cc: stable@vger.kernel.org
Cc: Jiri Kosina <jkosina@suze.cz>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 10 Jan 2018 22:49:39 +0000 (14:49 -0800)]
x86/pti: Make unpoison of pgd for trusted boot work for real
commit
445b69e3b75e42362a5bdc13c8b8f61599e2228a upstream.
The inital fix for trusted boot and PTI potentially misses the pgd clearing
if pud_alloc() sets a PGD. It probably works in *practice* because for two
adjacent calls to map_tboot_page() that share a PGD entry, the first will
clear NX, *then* allocate and set the PGD (without NX clear). The second
call will *not* allocate but will clear the NX bit.
Defer the NX clearing to a point after it is known that all top-level
allocations have occurred. Add a comment to clarify why.
[ tglx: Massaged changelog ]
[hughd notes: I have not tested tboot, but this looks to me as necessary
and as safe in old-Kaiser backports as it is upstream; I'm not submitting
the commit-to-be-fixed
262b6b30087, since it was undone by
445b69e3b75e,
and makes conflict trouble because of 5-level's p4d versus 4-level's pgd.]
Fixes:
262b6b30087 ("x86/tboot: Unbreak tboot with PTI enabled")
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: "Tim Chen" <tim.c.chen@linux.intel.com>
Cc: gnomes@lxorguk.ukuu.org.uk
Cc: peterz@infradead.org
Cc: ning.sun@intel.com
Cc: tboot-devel@lists.sourceforge.net
Cc: andi@firstfloor.org
Cc: luto@kernel.org
Cc: law@redhat.com
Cc: pbonzini@redhat.com
Cc: torvalds@linux-foundation.org
Cc: gregkh@linux-foundation.org
Cc: dwmw@amazon.co.uk
Cc: nickc@redhat.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180110224939.2695CD47@viggo.jf.intel.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Tue, 30 Jan 2018 02:37:46 +0000 (03:37 +0100)]
bpf: reject stores into ctx via st and xadd
[ upstream commit
f37a8cb84cce18762e8f86a70bd6a49a66ab964c ]
Alexei found that verifier does not reject stores into context
via BPF_ST instead of BPF_STX. And while looking at it, we
also should not allow XADD variant of BPF_STX.
The context rewriter is only assuming either BPF_LDX_MEM- or
BPF_STX_MEM-type operations, thus reject anything other than
that so that assumptions in the rewriter properly hold. Add
test cases as well for BPF selftests.
Fixes:
d691f9e8d440 ("bpf: allow programs to write to certain skb fields")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov [Tue, 30 Jan 2018 02:37:45 +0000 (03:37 +0100)]
bpf: fix 32-bit divide by zero
[ upstream commit
68fda450a7df51cff9e5a4d4a4d9d0d5f2589153 ]
due to some JITs doing if (src_reg == 0) check in 64-bit mode
for div/mod operations mask upper 32-bits of src register
before doing the check
Fixes:
622582786c9e ("net: filter: x86: internal BPF JIT")
Fixes:
7a12b5031c6b ("sparc64: Add eBPF JIT.")
Reported-by: syzbot+48340bb518e88849e2e3@syzkaller.appspotmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 30 Jan 2018 02:37:44 +0000 (03:37 +0100)]
bpf: fix divides by zero
[ upstream commit
c366287ebd698ef5e3de300d90cd62ee9ee7373e ]
Divides by zero are not nice, lets avoid them if possible.
Also do_div() seems not needed when dealing with 32bit operands,
but this seems a minor detail.
Fixes:
bd4cf0ed331a ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Tue, 30 Jan 2018 02:37:43 +0000 (03:37 +0100)]
bpf: avoid false sharing of map refcount with max_entries
[ upstream commit
be95a845cc4402272994ce290e3ad928aff06cb9 ]
In addition to commit
b2157399cc98 ("bpf: prevent out-of-bounds
speculation") also change the layout of struct bpf_map such that
false sharing of fast-path members like max_entries is avoided
when the maps reference counter is altered. Therefore enforce
them to be placed into separate cachelines.
pahole dump after change:
struct bpf_map {
const struct bpf_map_ops * ops; /* 0 8 */
struct bpf_map * inner_map_meta; /* 8 8 */
void * security; /* 16 8 */
enum bpf_map_type map_type; /* 24 4 */
u32 key_size; /* 28 4 */
u32 value_size; /* 32 4 */
u32 max_entries; /* 36 4 */
u32 map_flags; /* 40 4 */
u32 pages; /* 44 4 */
u32 id; /* 48 4 */
int numa_node; /* 52 4 */
bool unpriv_array; /* 56 1 */
/* XXX 7 bytes hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
struct user_struct * user; /* 64 8 */
atomic_t refcnt; /* 72 4 */
atomic_t usercnt; /* 76 4 */
struct work_struct work; /* 80 32 */
char name[16]; /* 112 16 */
/* --- cacheline 2 boundary (128 bytes) --- */
/* size: 128, cachelines: 2, members: 17 */
/* sum members: 121, holes: 1, sum holes: 7 */
};
Now all entries in the first cacheline are read only throughout
the life time of the map, set up once during map creation. Overall
struct size and number of cachelines doesn't change from the
reordering. struct bpf_map is usually first member and embedded
in map structs in specific map implementations, so also avoid those
members to sit at the end where it could potentially share the
cacheline with first map values e.g. in the array since remote
CPUs could trigger map updates just as well for those (easily
dirtying members like max_entries intentionally as well) while
having subsequent values in cache.
Quoting from Google's Project Zero blog [1]:
Additionally, at least on the Intel machine on which this was
tested, bouncing modified cache lines between cores is slow,
apparently because the MESI protocol is used for cache coherence
[8]. Changing the reference counter of an eBPF array on one
physical CPU core causes the cache line containing the reference
counter to be bounced over to that CPU core, making reads of the
reference counter on all other CPU cores slow until the changed
reference counter has been written back to memory. Because the
length and the reference counter of an eBPF array are stored in
the same cache line, this also means that changing the reference
counter on one physical CPU core causes reads of the eBPF array's
length to be slow on other physical CPU cores (intentional false
sharing).
While this doesn't 'control' the out-of-bounds speculation through
masking the index as in commit
b2157399cc98, triggering a manipulation
of the map's reference counter is really trivial, so lets not allow
to easily affect max_entries from it.
Splitting to separate cachelines also generally makes sense from
a performance perspective anyway in that fast-path won't have a
cache miss if the map gets pinned, reused in other progs, etc out
of control path, thus also avoids unintentional false sharing.
[1] https://googleprojectzero.blogspot.ch/2018/01/reading-privileged-memory-with-side.html
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Tue, 30 Jan 2018 02:37:42 +0000 (03:37 +0100)]
bpf: arsh is not supported in 32 bit alu thus reject it
[ upstream commit
7891a87efc7116590eaba57acc3c422487802c6f ]
The following snippet was throwing an 'unknown opcode cc' warning
in BPF interpreter:
0: (18) r0 = 0x0
2: (7b) *(u64 *)(r10 -16) = r0
3: (cc) (u32) r0 s>>= (u32) r0
4: (95) exit
Although a number of JITs do support BPF_ALU | BPF_ARSH | BPF_{K,X}
generation, not all of them do and interpreter does neither. We can
leave existing ones and implement it later in bpf-next for the
remaining ones, but reject this properly in verifier for the time
being.
Fixes:
17a5267067f3 ("bpf: verifier (add verifier core)")
Reported-by: syzbot+93c4904c5c70348a6890@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov [Tue, 30 Jan 2018 02:37:41 +0000 (03:37 +0100)]
bpf: introduce BPF_JIT_ALWAYS_ON config
[ upstream commit
290af86629b25ffd1ed6232c4e9107da031705cb ]
The BPF interpreter has been used as part of the spectre 2 attack CVE-2017-5715.
A quote from goolge project zero blog:
"At this point, it would normally be necessary to locate gadgets in
the host kernel code that can be used to actually leak data by reading
from an attacker-controlled location, shifting and masking the result
appropriately and then using the result of that as offset to an
attacker-controlled address for a load. But piecing gadgets together
and figuring out which ones work in a speculation context seems annoying.
So instead, we decided to use the eBPF interpreter, which is built into
the host kernel - while there is no legitimate way to invoke it from inside
a VM, the presence of the code in the host kernel's text section is sufficient
to make it usable for the attack, just like with ordinary ROP gadgets."
To make attacker job harder introduce BPF_JIT_ALWAYS_ON config
option that removes interpreter from the kernel in favor of JIT-only mode.
So far eBPF JIT is supported by:
x64, arm64, arm32, sparc64, s390, powerpc64, mips64
The start of JITed program is randomized and code page is marked as read-only.
In addition "constant blinding" can be turned on with net.core.bpf_jit_harden
v2->v3:
- move __bpf_prog_ret0 under ifdef (Daniel)
v1->v2:
- fix init order, test_bpf and cBPF (Daniel's feedback)
- fix offloaded bpf (Jakub's feedback)
- add 'return 0' dummy in case something can invoke prog->bpf_func
- retarget bpf tree. For bpf-next the patch would need one extra hunk.
It will be sent when the trees are merged back to net-next
Considered doing:
int bpf_jit_enable __read_mostly = BPF_EBPF_JIT_DEFAULT;
but it seems better to land the patch as-is and in bpf-next remove
bpf_jit_enable global variable from all JITs, consolidate in one place
and remove this jit_init() function.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov [Tue, 30 Jan 2018 02:37:40 +0000 (03:37 +0100)]
bpf: fix bpf_tail_call() x64 JIT
[ upstream commit
90caccdd8cc0215705f18b92771b449b01e2474a ]
- bpf prog_array just like all other types of bpf array accepts 32-bit index.
Clarify that in the comment.
- fix x64 JIT of bpf_tail_call which was incorrectly loading 8 instead of 4 bytes
- tighten corresponding check in the interpreter to stay consistent
The JIT bug can be triggered after introduction of BPF_F_NUMA_NODE flag
in commit
96eabe7a40aa in 4.14. Before that the map_flags would stay zero and
though JIT code is wrong it will check bounds correctly.
Hence two fixes tags. All other JITs don't have this problem.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fixes:
96eabe7a40aa ("bpf: Allow selecting numa node during map creation")
Fixes:
b52f00e6a715 ("x86: bpf_jit: implement bpf_tail_call() helper")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 30 Jan 2018 02:37:39 +0000 (03:37 +0100)]
x86: bpf_jit: small optimization in emit_bpf_tail_call()
[ upstream commit
84ccac6e7854ebbfb56d2fc6d5bef9be49bb304c ]
Saves 4 bytes replacing following instructions :
lea rax, [rsi + rdx * 8 + offsetof(...)]
mov rax, qword ptr [rax]
cmp rax, 0
by :
mov rax, [rsi + rdx * 8 + offsetof(...)]
test rax, rax
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov [Tue, 30 Jan 2018 02:37:38 +0000 (03:37 +0100)]
bpf: fix branch pruning logic
[ Upstream commit
c131187db2d3fa2f8bf32fdf4e9a4ef805168467 ]
when the verifier detects that register contains a runtime constant
and it's compared with another constant it will prune exploration
of the branch that is guaranteed not to be taken at runtime.
This is all correct, but malicious program may be constructed
in such a way that it always has a constant comparison and
the other branch is never taken under any conditions.
In this case such path through the program will not be explored
by the verifier. It won't be taken at run-time either, but since
all instructions are JITed the malicious program may cause JITs
to complain about using reserved fields, etc.
To fix the issue we have to track the instructions explored by
the verifier and sanitize instructions that are dead at run time
with NOPs. We cannot reject such dead code, since llvm generates
it for valid C code, since it doesn't do as much data flow
analysis as the verifier does.
Fixes:
17a5267067f3 ("bpf: verifier (add verifier core)")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 6 Jan 2018 00:26:00 +0000 (16:26 -0800)]
loop: fix concurrent lo_open/lo_release
commit
ae6650163c66a7eff1acd6eb8b0f752dcfa8eba5 upstream.
范龙飞 reports that KASAN can report a use-after-free in __lock_acquire.
The reason is due to insufficient serialization in lo_release(), which
will continue to use the loop device even after it has decremented the
lo_refcnt to zero.
In the meantime, another process can come in, open the loop device
again as it is being shut down. Confusion ensues.
Reported-by: 范龙飞 <long7573@126.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 31 Jan 2018 11:06:14 +0000 (12:06 +0100)]
Linux 4.4.114
Ben Hutchings [Mon, 22 Jan 2018 20:11:06 +0000 (20:11 +0000)]
nfsd: auth: Fix gid sorting when rootsquash enabled
commit
1995266727fa8143897e89b55f5d3c79aa828420 upstream.
Commit
bdcf0a423ea1 ("kernel: make groups_sort calling a responsibility
group_info allocators") appears to break nfsd rootsquash in a pretty
major way.
It adds a call to groups_sort() inside the loop that copies/squashes
gids, which means the valid gids are sorted along with the following
garbage. The net result is that the highest numbered valid gids are
replaced with any lower-valued garbage gids, possibly including 0.
We should sort only once, after filling in all the gids.
Fixes:
bdcf0a423ea1 ("kernel: make groups_sort calling a responsibility ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Streetman [Thu, 18 Jan 2018 21:14:26 +0000 (16:14 -0500)]
net: tcp: close sock if net namespace is exiting
[ Upstream commit
4ee806d51176ba7b8ff1efd81f271d7252e03a1d ]
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Wed, 17 Jan 2018 22:21:13 +0000 (14:21 -0800)]
flow_dissector: properly cap thoff field
[ Upstream commit
d0c081b49137cd3200f2023c0875723be66e7ce5 ]
syzbot reported yet another crash [1] that is caused by
insufficient validation of DODGY packets.
Two bugs are happening here to trigger the crash.
1) Flow dissection leaves with incorrect thoff field.
2) skb_probe_transport_header() sets transport header to this invalid
thoff, even if pointing after skb valid data.
3) qdisc_pkt_len_init() reads out-of-bound data because it
trusts tcp_hdrlen(skb)
Possible fixes :
- Full flow dissector validation before injecting bad DODGY packets in
the stack.
This approach was attempted here : https://patchwork.ozlabs.org/patch/
861874/
- Have more robust functions in the core.
This might be needed anyway for stable versions.
This patch fixes the flow dissection issue.
[1]
CPU: 1 PID: 3144 Comm: syzkaller271204 Not tainted 4.15.0-rc4-mm1+ #49
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:355 [inline]
kasan_report+0x23b/0x360 mm/kasan/report.c:413
__asan_report_load2_noabort+0x14/0x20 mm/kasan/report.c:432
__tcp_hdrlen include/linux/tcp.h:35 [inline]
tcp_hdrlen include/linux/tcp.h:40 [inline]
qdisc_pkt_len_init net/core/dev.c:3160 [inline]
__dev_queue_xmit+0x20d3/0x2200 net/core/dev.c:3465
dev_queue_xmit+0x17/0x20 net/core/dev.c:3554
packet_snd net/packet/af_packet.c:2943 [inline]
packet_sendmsg+0x3ad5/0x60a0 net/packet/af_packet.c:2968
sock_sendmsg_nosec net/socket.c:628 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:638
sock_write_iter+0x31a/0x5d0 net/socket.c:907
call_write_iter include/linux/fs.h:1776 [inline]
new_sync_write fs/read_write.c:469 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:482
vfs_write+0x189/0x510 fs/read_write.c:544
SYSC_write fs/read_write.c:589 [inline]
SyS_write+0xef/0x220 fs/read_write.c:581
entry_SYSCALL_64_fastpath+0x1f/0x96
Fixes:
34fad54c2537 ("net: __skb_flow_dissect() must cap its return value")
Fixes:
a6e544b0a88b ("flow_dissector: Jump to exit code in __skb_flow_dissect")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Westfall [Sun, 14 Jan 2018 12:18:51 +0000 (04:18 -0800)]
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
[ Upstream commit
cd9ff4de0107c65d69d02253bb25d6db93c3dbc1 ]
Map all lookup neigh keys to INADDR_ANY for loopback/point-to-point devices
to avoid making an entry for every remote ip the device needs to talk to.
This used the be the old behavior but became broken in
a263b3093641f
(ipv4: Make neigh lookups directly in output packet path) and later removed
in
0bb4087cbec0 (ipv4: Fix neigh lookup keying over loopback/point-to-point
devices) because it was broken.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Westfall [Sun, 14 Jan 2018 12:18:50 +0000 (04:18 -0800)]
net: Allow neigh contructor functions ability to modify the primary_key
[ Upstream commit
096b9854c04df86f03b38a97d40b6506e5730919 ]
Use n->primary_key instead of pkey to account for the possibility that a neigh
constructor function may have modified the primary_key value.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neil Horman [Mon, 22 Jan 2018 21:06:37 +0000 (16:06 -0500)]
vmxnet3: repair memory leak
[ Upstream commit
848b159835ddef99cc4193083f7e786c3992f580 ]
with the introduction of commit
b0eb57cb97e7837ebb746404c2c58c6f536f23fa, it appears that rq->buf_info
is improperly handled. While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when the mtu of a vmxnet3 interface is changed
frequently.
Fix is pretty straight forward, just move the NULL set to after the
free.
Tested by myself with successful results
Applies to net, and should likely be queued for stable, please
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin Long [Mon, 15 Jan 2018 09:01:36 +0000 (17:01 +0800)]
sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
[ Upstream commit
a0ff660058b88d12625a783ce9e5c1371c87951f ]
After commit
cea0cc80a677 ("sctp: use the right sk after waking up from
wait_buf sleep"), it may change to lock another sk if the asoc has been
peeled off in sctp_wait_for_sndbuf.
However, the asoc's new sk could be already closed elsewhere, as it's in
the sendmsg context of the old sk that can't avoid the new sk's closing.
If the sk's last one refcnt is held by this asoc, later on after putting
this asoc, the new sk will be freed, while under it's own lock.
This patch is to revert that commit, but fix the old issue by returning
error under the old sk's lock.
Fixes:
cea0cc80a677 ("sctp: use the right sk after waking up from wait_buf sleep")
Reported-by: syzbot+ac6ea7baa4432811eb50@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin Long [Mon, 15 Jan 2018 09:02:00 +0000 (17:02 +0800)]
sctp: do not allow the v4 socket to bind a v4mapped v6 address
[ Upstream commit
c5006b8aa74599ce19104b31d322d2ea9ff887cc ]
The check in sctp_sockaddr_af is not robust enough to forbid binding a
v4mapped v6 addr on a v4 socket.
The worse thing is that v4 socket's bind_verify would not convert this
v4mapped v6 addr to a v4 addr. syzbot even reported a crash as the v4
socket bound a v6 addr.
This patch is to fix it by doing the common sa.sa_family check first,
then AF_INET check for v4mapped v6 addrs.
Fixes:
7dab83de50c7 ("sctp: Support ipv6only AF_INET6 sockets.")
Reported-by: syzbot+7b7b518b1228d2743963@syzkaller.appspotmail.com
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Francois Romieu [Fri, 26 Jan 2018 00:53:26 +0000 (01:53 +0100)]
r8169: fix memory corruption on retrieval of hardware statistics.
[ Upstream commit
a78e93661c5fd30b9e1dee464b2f62f966883ef7 ]
Hardware statistics retrieval hurts in tight invocation loops.
Avoid extraneous write and enforce strict ordering of writes targeted to
the tally counters dump area address registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Oliver Freyermuth <o.freyermuth@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guillaume Nault [Mon, 22 Jan 2018 17:06:37 +0000 (18:06 +0100)]
pppoe: take ->needed_headroom of lower device into account on xmit
[ Upstream commit
02612bb05e51df8489db5e94d0cf8d1c81f87b0c ]
In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit
f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom").
But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.
This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.
skbuff: skb_under_panic: text:
000000001d390b3a len:31 put:24
head:
00000000d8ed776f data:
000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-
20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:
ffff8801d9bd7840 EFLAGS:
00010282
RAX:
0000000000000083 RBX:
ffff8801d4f083c0 RCX:
0000000000000000
RDX:
0000000000000083 RSI:
1ffff1003b37ae92 RDI:
ffffed003b37aefc
RBP:
ffff8801d9bd78a8 R08:
1ffff1003b37ae8a R09:
0000000000000000
R10:
0000000000000001 R11:
0000000000000000 R12:
ffffffff86200de0
R13:
ffffffff84a981ad R14:
0000000000000018 R15:
ffff8801d2d34180
FS:
00000000019c4880(0000) GS:
ffff8801db300000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000208bc000 CR3:
00000001d9111001 CR4:
00000000001606e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
skb_under_panic net/core/skbuff.c:114 [inline]
skb_push+0xce/0xf0 net/core/skbuff.c:1714
ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
dev_hard_header include/linux/netdevice.h:2723 [inline]
pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:640
sock_write_iter+0x31a/0x5d0 net/socket.c:909
call_write_iter include/linux/fs.h:1775 [inline]
do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
do_iter_write+0x154/0x540 fs/read_write.c:932
vfs_writev+0x18a/0x340 fs/read_write.c:977
do_writev+0xfc/0x2a0 fs/read_write.c:1012
SYSC_writev fs/read_write.c:1085 [inline]
SyS_writev+0x27/0x30 fs/read_write.c:1082
entry_SYSCALL_64_fastpath+0x29/0xa0
Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.
Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().
Fixes:
f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 19 Jan 2018 03:59:19 +0000 (19:59 -0800)]
net: qdisc_pkt_len_init() should be more robust
[ Upstream commit
7c68d1a6b4db9012790af7ac0f0fdc0d2083422a ]
Without proper validation of DODGY packets, we might very well
feed qdisc_pkt_len_init() with invalid GSO packets.
tcp_hdrlen() might access out-of-bound data, so let's use
skb_header_pointer() and proper checks.
Whole story is described in commit
d0c081b49137 ("flow_dissector:
properly cap thoff field")
We have the goal of validating DODGY packets earlier in the stack,
so we might very well revert this fix in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Reported-by: syzbot+9da69ebac7dddd804552@syzkaller.appspotmail.com
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Craig Gallek [Wed, 10 Feb 2016 16:50:37 +0000 (11:50 -0500)]
tcp: __tcp_hdrlen() helper
commit
d9b3fca27385eafe61c3ca6feab6cb1e7dc77482 upstream.
tcp_hdrlen is wasteful if you already have a pointer to struct tcphdr.
This splits the size calculation into a helper function that can be
used if a struct tcphdr is already available.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Fri, 19 Jan 2018 10:50:46 +0000 (11:50 +0100)]
net: igmp: fix source address check for IGMPv3 reports
[ Upstream commit
ad23b750933ea7bf962678972a286c78a8fa36aa ]
Commit "net: igmp: Use correct source address on IGMPv3 reports"
introduced a check to validate the source address of locally generated
IGMPv3 packets.
Instead of checking the local interface address directly, it uses
inet_ifa_match(fl4->saddr, ifa), which checks if the address is on the
local subnet (or equal to the point-to-point address if used).
This breaks for point-to-point interfaces, so check against
ifa->ifa_local directly.
Cc: Kevin Cernekee <cernekee@chromium.org>
Fixes:
a46182b00290 ("net: igmp: Use correct source address on IGMPv3 reports")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Florian Wolters <florian@florian-wolters.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuiko Oshino [Mon, 15 Jan 2018 18:24:28 +0000 (13:24 -0500)]
lan78xx: Fix failure in USB Full Speed
[ Upstream commit
a5b1379afbfabf91e3a689e82ac619a7157336b3 ]
Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.
Fixes:
55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 12 Jan 2018 06:31:18 +0000 (22:31 -0800)]
ipv6: ip6_make_skb() needs to clear cork.base.dst
[ Upstream commit
95ef498d977bf44ac094778fd448b98af158a3e6 ]
In my last patch, I missed fact that cork.base.dst was not initialized
in ip6_make_skb() :
If ip6_setup_cork() returns an error, we might attempt a dst_release()
on some random pointer.
Fixes:
862c03ee1deb ("ipv6: fix possible mem leaks in ipv6_make_skb()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Maloney [Wed, 10 Jan 2018 17:45:10 +0000 (12:45 -0500)]
ipv6: fix udpv6 sendmsg crash caused by too small MTU
[ Upstream commit
749439bfac6e1a2932c582e2699f91d329658196 ]
The logic in __ip6_append_data() assumes that the MTU is at least large
enough for the headers. A device's MTU may be adjusted after being
added while sendmsg() is processing data, resulting in
__ip6_append_data() seeing any MTU. For an mtu smaller than the size of
the fragmentation header, the math results in a negative 'maxfraglen',
which causes problems when refragmenting any previous skb in the
skb_write_queue, leaving it possibly malformed.
Instead sendmsg returns EINVAL when the mtu is calculated to be less
than IPV6_MIN_MTU.
Found by syzkaller:
kernel BUG at ./include/linux/skbuff.h:2064!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 14216 Comm: syz-executor5 Not tainted 4.13.0-rc4+ #2
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task:
ffff8801d0b68580 task.stack:
ffff8801ac6b8000
RIP: 0010:__skb_pull include/linux/skbuff.h:2064 [inline]
RIP: 0010:__ip6_make_skb+0x18cf/0x1f70 net/ipv6/ip6_output.c:1617
RSP: 0018:
ffff8801ac6bf570 EFLAGS:
00010216
RAX:
0000000000010000 RBX:
0000000000000028 RCX:
ffffc90003cce000
RDX:
00000000000001b8 RSI:
ffffffff839df06f RDI:
ffff8801d9478ca0
RBP:
ffff8801ac6bf780 R08:
ffff8801cc3f1dbc R09:
0000000000000000
R10:
ffff8801ac6bf7a0 R11:
43cb4b7b1948a9e7 R12:
ffff8801cc3f1dc8
R13:
ffff8801cc3f1d40 R14:
0000000000001036 R15:
dffffc0000000000
FS:
00007f43d740c700(0000) GS:
ffff8801dc100000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f7834984000 CR3:
00000001d79b9000 CR4:
00000000001406e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
ip6_finish_skb include/net/ipv6.h:911 [inline]
udp_v6_push_pending_frames+0x255/0x390 net/ipv6/udp.c:1093
udpv6_sendmsg+0x280d/0x31a0 net/ipv6/udp.c:1363
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:762
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
SYSC_sendto+0x352/0x5a0 net/socket.c:1750
SyS_sendto+0x40/0x50 net/socket.c:1718
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4512e9
RSP: 002b:
00007f43d740bc08 EFLAGS:
00000216 ORIG_RAX:
000000000000002c
RAX:
ffffffffffffffda RBX:
00000000007180a8 RCX:
00000000004512e9
RDX:
000000000000002e RSI:
0000000020d08000 RDI:
0000000000000005
RBP:
0000000000000086 R08:
00000000209c1000 R09:
000000000000001c
R10:
0000000000040800 R11:
0000000000000216 R12:
00000000004b9c69
R13:
00000000ffffffff R14:
0000000000000005 R15:
00000000202c2000
Code: 9e 01 fe e9 c5 e8 ff ff e8 7f 9e 01 fe e9 4a ea ff ff 48 89 f7 e8 52 9e 01 fe e9 aa eb ff ff e8 a8 b6 cf fd 0f 0b e8 a1 b6 cf fd <0f> 0b 49 8d 45 78 4d 8d 45 7c 48 89 85 78 fe ff ff 49 8d 85 ba
RIP: __skb_pull include/linux/skbuff.h:2064 [inline] RSP:
ffff8801ac6bf570
RIP: __ip6_make_skb+0x18cf/0x1f70 net/ipv6/ip6_output.c:1617 RSP:
ffff8801ac6bf570
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Mike Maloney <maloney@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Mon, 22 Jan 2018 20:06:42 +0000 (20:06 +0000)]
ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
[ Upstream commit
e9191ffb65d8e159680ce0ad2224e1acbde6985c ]
Commit
513674b5a2c9 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.
The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled. Fix it to return the effective value, whether
that has been set at the socket or net namespace level.
Fixes:
513674b5a2c9 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Kodanev [Fri, 26 Jan 2018 12:14:16 +0000 (15:14 +0300)]
dccp: don't restart ccid2_hc_tx_rto_expire() if sk in closed state
[ Upstream commit
dd5684ecae3bd8e44b644f50e2c12c7e57fdfef5 ]
ccid2_hc_tx_rto_expire() timer callback always restarts the timer
again and can run indefinitely (unless it is stopped outside), and after
commit
120e9dabaf55 ("dccp: defer ccid_hc_tx_delete() at dismantle time"),
which moved ccid_hc_tx_delete() (also includes sk_stop_timer()) from
dccp_destroy_sock() to sk_destruct(), this started to happen quite often.
The timer prevents releasing the socket, as a result, sk_destruct() won't
be called.
Found with LTP/dccp_ipsec tests running on the bonding device,
which later couldn't be unloaded after the tests were completed:
unregister_netdevice: waiting for bond0 to become free. Usage count = 148
Fixes:
2a91aa396739 ("[DCCP] CCID2: Initial CCID2 (TCP-Like) implementation")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Fri, 26 Jan 2018 13:54:32 +0000 (14:54 +0100)]
hrtimer: Reset hrtimer cpu base proper on CPU hotplug
commit
d5421ea43d30701e03cadc56a38854c36a8b4433 upstream.
The hrtimer interrupt code contains a hang detection and mitigation
mechanism, which prevents that a long delayed hrtimer interrupt causes a
continous retriggering of interrupts which prevent the system from making
progress. If a hang is detected then the timer hardware is programmed with
a certain delay into the future and a flag is set in the hrtimer cpu base
which prevents newly enqueued timers from reprogramming the timer hardware
prior to the chosen delay. The subsequent hrtimer interrupt after the delay
clears the flag and resumes normal operation.
If such a hang happens in the last hrtimer interrupt before a CPU is
unplugged then the hang_detected flag is set and stays that way when the
CPU is plugged in again. At that point the timer hardware is not armed and
it cannot be armed because the hang_detected flag is still active, so
nothing clears that flag. As a consequence the CPU does not receive hrtimer
interrupts and no timers expire on that CPU which results in RCU stalls and
other malfunctions.
Clear the flag along with some other less critical members of the hrtimer
cpu base to ensure starting from a clean state when a CPU is plugged in.
Thanks to Paul, Sebastian and Anna-Maria for their help to get down to the
root cause of that hard to reproduce heisenbug. Once understood it's
trivial and certainly justifies a brown paperbag.
Fixes:
41d2e4949377 ("hrtimer: Tune hrtimer_interrupt hang logic")
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801261447590.2067@nanos
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jia Zhang [Tue, 23 Jan 2018 10:41:32 +0000 (11:41 +0100)]
x86/microcode/intel: Extend BDW late-loading further with LLC size check
commit
7e702d17ed138cf4ae7c00e8c00681ed464587c7 upstream.
Commit
b94b73733171 ("x86/microcode/intel: Extend BDW late-loading with a
revision check") reduced the impact of erratum BDF90 for Broadwell model
79.
The impact can be reduced further by checking the size of the last level
cache portion per core.
Tony: "The erratum says the problem only occurs on the large-cache SKUs.
So we only need to avoid the update if we are on a big cache SKU that is
also running old microcode."
For more details, see erratum BDF90 in document #334165 (Intel Xeon
Processor E7-8800/4800 v4 Product Family Specification Update) from
September 2017.
Fixes:
b94b73733171 ("x86/microcode/intel: Extend BDW late-loading with a revision check")
Signed-off-by: Jia Zhang <zhang.jia@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/1516321542-31161-1-git-send-email-zhang.jia@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg KH [Wed, 8 Mar 2017 18:03:44 +0000 (19:03 +0100)]
eventpoll.h: add missing epoll event masks
commit
7e040726850a106587485c21bdacc0bfc8a0cbed upstream.
[resend due to me forgetting to cc: linux-api the first time around I
posted these back on Feb 23]
From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason these values are not in the uapi header file, so any
libc has to define it themselves. To prevent them from needing to do
this, just have the kernel provide the correct values.
Reported-by: Elliott Hughes <enh@google.com>
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Fri, 26 Jan 2018 16:23:02 +0000 (16:23 +0000)]
vsyscall: Fix permissions for emulate mode with KAISER/PTI
The backport of KAISER to 4.4 turned vsyscall emulate mode into native
mode. Add a vsyscall_pgprot variable to hold the correct page
protections, like Borislav and Hugh did for 3.2 and 3.18.
Cc: Borislav Petkov <bp@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Meyer [Sun, 20 Aug 2017 11:26:04 +0000 (13:26 +0200)]
um: link vmlinux with -no-pie
commit
883354afbc109c57f925ccc19840055193da0cc0 upstream.
Debian's gcc defaults to pie. The global Makefile already defines the -fno-pie option.
Link UML dynamic kernel image also with -no-pie to fix the build.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Bernie Innocenti <codewiz@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuah Khan [Fri, 15 Dec 2017 17:50:09 +0000 (10:50 -0700)]
usbip: prevent leaking socket pointer address in messages
commit
90120d15f4c397272aaf41077960a157fc4212bf upstream.
usbip driver is leaking socket pointer address in messages. Remove
the messages that aren't useful and print sockfd in the ones that
are useful for debugging.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuah Khan [Thu, 7 Dec 2017 21:16:48 +0000 (14:16 -0700)]
usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input
commit
c6688ef9f29762e65bce325ef4acd6c675806366 upstream.
Harden CMD_SUBMIT path to handle malicious input that could trigger
large memory allocations. Add checks to validate transfer_buffer_length
and number_of_packets to protect against bad input requesting for
unbounded memory allocations. Validate early in get_pipe() and return
failure.
Reported-by: Secunia Research <vuln@secunia.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuah Khan [Thu, 7 Dec 2017 21:16:47 +0000 (14:16 -0700)]
usbip: fix stub_rx: get_pipe() to validate endpoint number
commit
635f545a7e8be7596b9b2b6a43cab6bbd5a88e43 upstream.
get_pipe() routine doesn't validate the input endpoint number
and uses to reference ep_in and ep_out arrays. Invalid endpoint
number can trigger BUG(). Range check the epnum and returning
error instead of calling BUG().
Change caller stub_recv_cmd_submit() to handle the get_pipe()
error return.
Reported-by: Secunia Research <vuln@secunia.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Goodbody [Tue, 2 Feb 2016 17:36:39 +0000 (17:36 +0000)]
usb: usbip: Fix possible deadlocks reported by lockdep
commit
21619792d1eca7e772ca190ba68588e57f29595b upstream.
Change spin_lock calls to spin_lock_irqsave to prevent
attmpted recursive lock taking in interrupt context.
This patch fixes Bug 109351
https://bugzilla.kernel.org/show_bug.cgi?id=109351
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aaron Ma [Fri, 19 Jan 2018 17:43:39 +0000 (09:43 -0800)]
Input: trackpoint - force 3 buttons if 0 button is reported
commit
f5d07b9e98022d50720e38aa936fc11c67868ece upstream.
Lenovo introduced trackpoint compatible sticks with minimum PS/2 commands.
They supposed to reply with 0x02, 0x03, or 0x04 in response to the
"Read Extended ID" command, so we would know not to try certain extended
commands. Unfortunately even some trackpoints reporting the original IBM
version (0x01 firmware 0x0e) now respond with incorrect data to the "Get
Extended Buttons" command:
thinkpad_acpi: ThinkPad BIOS R0DET87W (1.87 ), EC unknown
thinkpad_acpi: Lenovo ThinkPad E470, model 20H1004SGE
psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 0/0
Since there are no trackpoints without buttons, let's assume the trackpoint
has 3 buttons when we get 0 response to the extended buttons query.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196253
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 24 Jan 2018 14:28:17 +0000 (15:28 +0100)]
Revert "module: Add retpoline tag to VERMAGIC"
commit
5132ede0fe8092b043dae09a7cc32b8ae7272baa upstream.
This reverts commit
6cfb521ac0d5b97470883ff9b7facae264b7ab12.
Turns out distros do not want to make retpoline as part of their "ABI",
so this patch should not have been merged. Sorry Andi, this was my
fault, I suggested it when your original patch was the "correct" way of
doing this instead.
Reported-by: Jiri Kosina <jikos@kernel.org>
Fixes:
6cfb521ac0d5 ("module: Add retpoline tag to VERMAGIC")
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Thumshirn [Mon, 9 Oct 2017 11:33:19 +0000 (13:33 +0200)]
scsi: libiscsi: fix shifting of DID_REQUEUE host byte
commit
eef9ffdf9cd39b2986367bc8395e2772bc1284ba upstream.
The SCSI host byte should be shifted left by 16 in order to have
scsi_decide_disposition() do the right thing (.i.e. requeue the
command).
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes:
661134ad3765 ("[SCSI] libiscsi, bnx2i: make bound ep check common")
Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Cc: Chris Leech <cleech@redhat.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Tue, 13 Jun 2017 11:35:51 +0000 (13:35 +0200)]
fs/fcntl: f_setown, avoid undefined behaviour
commit
fc3dc67471461c0efcb1ed22fb7595121d65fad9 upstream.
fcntl(0, F_SETOWN, 0x80000000) triggers:
UBSAN: Undefined behaviour in fs/fcntl.c:118:7
negation of -
2147483648 cannot be represented in type 'int':
CPU: 1 PID: 18261 Comm: syz-executor Not tainted 4.8.1-0-syzkaller #1
...
Call Trace:
...
[<
ffffffffad8f0868>] ? f_setown+0x1d8/0x200
[<
ffffffffad8f19a9>] ? SyS_fcntl+0x999/0xf30
[<
ffffffffaed1fb00>] ? entry_SYSCALL_64_fastpath+0x23/0xc1
Fix that by checking the arg parameter properly (against INT_MAX) before
"who = -who". And return immediatelly with -EINVAL in case it is wrong.
Note that according to POSIX we can return EINVAL:
http://pubs.opengroup.org/onlinepubs/
9699919799/functions/fcntl.html
[EINVAL]
The cmd argument is F_SETOWN and the value of the argument
is not valid as a process or process group identifier.
[v2] returns an error, v1 used to fail silently
[v3] implement proper check for the bad value INT_MIN
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jeff Layton <jlayton@poochiereds.net>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Thu, 22 Jun 2017 07:32:49 +0000 (09:32 +0200)]
reiserfs: Don't clear SGID when inheriting ACLs
commit
6883cd7f68245e43e91e5ee583b7550abf14523f upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__reiserfs_set_acl() into reiserfs_set_acl(). That way the function will
not be called when inheriting ACLs which is what we want as it prevents
SGID bit clearing and the mode has been properly set by
posix_acl_create() anyway.
Fixes:
073931017b49d9458aa351605b43a7e34598caef
CC: reiserfs-devel@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Mahoney [Thu, 22 Jun 2017 20:35:04 +0000 (16:35 -0400)]
reiserfs: don't preallocate blocks for extended attributes
commit
54930dfeb46e978b447af0fb8ab4e181c1bf9d7a upstream.
Most extended attributes will fit in a single block. More importantly,
we drop the reference to the inode while holding the transaction open
so the preallocated blocks aren't released. As a result, the inode
may be evicted before it's removed from the transaction's prealloc list
which can cause memory corruption.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Mahoney [Thu, 22 Jun 2017 20:47:34 +0000 (16:47 -0400)]
reiserfs: fix race in prealloc discard
commit
08db141b5313ac2f64b844fb5725b8d81744b417 upstream.
The main loop in __discard_prealloc is protected by the reiserfs write lock
which is dropped across schedules like the BKL it replaced. The problem is
that it checks the value, calls a routine that schedules, and then adjusts
the state. As a result, two threads that are calling
reiserfs_prealloc_discard at the same time can race when one calls
reiserfs_free_prealloc_block, the lock is dropped, and the other calls
reiserfs_free_prealloc_block with the same block number. In the right
circumstances, it can cause the prealloc count to go negative.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Wed, 21 Jun 2017 12:34:15 +0000 (14:34 +0200)]
ext2: Don't clear SGID when inheriting ACLs
commit
a992f2d38e4ce17b8c7d1f7f67b2de0eebdea069 upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by creating __ext2_set_acl() function that does not call
posix_acl_update_mode() and use it when inheriting ACLs. That prevents
SGID bit clearing and the mode has been properly set by
posix_acl_create() anyway.
Fixes:
073931017b49d9458aa351605b43a7e34598caef
CC: stable@vger.kernel.org
CC: linux-ext4@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kevin Cernekee [Tue, 5 Dec 2017 23:42:41 +0000 (15:42 -0800)]
netfilter: xt_osf: Add missing permission checks
commit
916a27901de01446bcf57ecca4783f6cff493309 upstream.
The capability check in nfnetlink_rcv() verifies that the caller
has CAP_NET_ADMIN in the namespace that "owns" the netlink socket.
However, xt_osf_fingers is shared by all net namespaces on the
system. An unprivileged user can create user and net namespaces
in which he holds CAP_NET_ADMIN to bypass the netlink_net_capable()
check:
vpnns -- nfnl_osf -f /tmp/pf.os
vpnns -- nfnl_osf -f /tmp/pf.os -d
These non-root operations successfully modify the systemwide OS
fingerprint list. Add new capable() checks so that they can't.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kevin Cernekee [Sun, 3 Dec 2017 20:12:45 +0000 (12:12 -0800)]
netfilter: nfnetlink_cthelper: Add missing permission checks
commit
4b380c42f7d00a395feede754f0bc2292eebe6e5 upstream.
The capability check in nfnetlink_rcv() verifies that the caller
has CAP_NET_ADMIN in the namespace that "owns" the netlink socket.
However, nfnl_cthelper_list is shared by all net namespaces on the
system. An unprivileged user can create user and net namespaces
in which he holds CAP_NET_ADMIN to bypass the netlink_net_capable()
check:
$ nfct helper list
nfct v1.4.4: netlink error: Operation not permitted
$ vpnns -- nfct helper list
{
.name = ftp,
.queuenum = 0,
.l3protonum = 2,
.l4protonum = 6,
.priv_data_len = 24,
.status = enabled,
};
Add capable() checks in nfnetlink_cthelper, as this is cleaner than
trying to generalize the solution.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso [Fri, 29 Apr 2016 08:39:34 +0000 (10:39 +0200)]
netfilter: fix IS_ERR_VALUE usage
commit
92b4423e3a0bc5d43ecde4bcad871f8b5ba04efd upstream.
This is a forward-port of the original patch from Andrzej Hajda,
he said:
"IS_ERR_VALUE should be used only with unsigned long type.
Otherwise it can work incorrectly. To achieve this function
xt_percpu_counter_alloc is modified to return unsigned long,
and its result is assigned to temporary variable to perform
error checking, before assigning to .pcnt field.
The patch follows conclusion from discussion on LKML [1][2].
[1]: http://permalink.gmane.org/gmane.linux.kernel/
2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/
2150581"
Original patch from Andrzej is here:
http://patchwork.ozlabs.org/patch/582970/
This patch has clashed with input validation fixes for x_tables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Pau Espin Pedrol [Fri, 6 Jan 2017 19:33:27 +0000 (20:33 +0100)]
netfilter: use fwmark_reflect in nf_send_reset
commit
cc31d43b4154ad5a7d8aa5543255a93b7e89edc2 upstream.
Otherwise, RST packets generated by ipt_REJECT always have mark 0 when
the routing is checked later in the same code path.
Fixes:
e110861f8609 ("net: add a sysctl to reflect the fwmark on replies")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Pau Espin Pedrol <pau.espin@tessares.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ulrich Weber [Mon, 24 Oct 2016 16:07:23 +0000 (18:07 +0200)]
netfilter: nf_conntrack_sip: extend request line validation
commit
444f901742d054a4cd5ff045871eac5131646cfb upstream.
on SIP requests, so a fragmented TCP SIP packet from an allow header starting with
INVITE,NOTIFY,OPTIONS,REFER,REGISTER,UPDATE,SUBSCRIBE
Content-Length: 0
will not bet interpreted as an INVITE request. Also Request-URI must start with an alphabetic character.
Confirm with RFC 3261
Request-Line = Method SP Request-URI SP SIP-Version CRLF
Fixes:
30f33e6dee80 ("[NETFILTER]: nf_conntrack_sip: support method specific request/response handling")
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
Acked-by: Marco Angaroni <marcoangaroni@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Westphal [Thu, 25 Aug 2016 13:33:29 +0000 (15:33 +0200)]
netfilter: restart search if moved to other chain
commit
95a8d19f28e6b29377a880c6264391a62e07fccc upstream.
In case nf_conntrack_tuple_taken did not find a conflicting entry
check that all entries in this hash slot were tested and restart
in case an entry was moved to another chain.
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes:
ea781f197d6a ("netfilter: nf_conntrack: use SLAB_DESTROY_BY_RCU and get rid of call_rcu()")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liping Zhang [Mon, 8 Aug 2016 14:07:27 +0000 (22:07 +0800)]
netfilter: nfnetlink_queue: reject verdict request from different portid
commit
00a3101f561816e58de054a470484996f78eb5eb upstream.
Like NFQNL_MSG_VERDICT_BATCH do, we should also reject the verdict
request when the portid is not same with the initial portid(maybe
from another process).
Fixes:
97d32cf9440d ("netfilter: nfnetlink_queue: batch verdict support")
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liping Zhang [Mon, 8 Aug 2016 13:57:58 +0000 (21:57 +0800)]
netfilter: nf_ct_expect: remove the redundant slash when policy name is empty
commit
b173a28f62cf929324a8a6adcc45adadce311d16 upstream.
The 'name' filed in struct nf_conntrack_expect_policy{} is not a
pointer, so check it is NULL or not will always return true. Even if the
name is empty, slash will always be displayed like follows:
# cat /proc/net/nf_conntrack_expect
297 l3proto = 2 proto=6 src=1.1.1.1 dst=2.2.2.2 sport=1 dport=1025 ftp/
^
Fixes:
3a8fc53a45c4 ("netfilter: nf_ct_helper: allocate 16 bytes for the helper and policy names")
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Abeni [Thu, 26 May 2016 17:08:10 +0000 (19:08 +0200)]
netfilter: nf_dup_ipv6: set again FLOWI_FLAG_KNOWN_NH at flowi6_flags
commit
83170f3beccccd7ceb4f9a0ac0c4dc736afde90c upstream.
With the commit
48e8aa6e3137 ("ipv6: Set FLOWI_FLAG_KNOWN_NH at
flowi6_flags") ip6_pol_route() callers were asked to to set the
FLOWI_FLAG_KNOWN_NH properly and xt_TEE was updated accordingly,
but with the later refactor in commit
bbde9fc1824a ("netfilter:
factor out packet duplication for IPv4/IPv6") the flowi6_flags
update was lost.
This commit re-add it just before the routing decision.
Fixes:
bbde9fc1824a ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hongxu Jia [Wed, 30 Nov 2016 02:56:26 +0000 (21:56 -0500)]
netfilter: arp_tables: fix invoking 32bit "iptable -P INPUT ACCEPT" failed in 64bit kernel
commit
17a49cd549d9dc8707dc9262210166455c612dde upstream.
Since
09d9686047db ("netfilter: x_tables: do compat validation via
translate_table"), it used compatr structure to assign newinfo
structure. In translate_compat_table of ip_tables.c and ip6_tables.c,
it used compatr->hook_entry to replace info->hook_entry and
compatr->underflow to replace info->underflow, but not do the same
replacement in arp_tables.c.
It caused invoking 32-bit "arptbale -P INPUT ACCEPT" failed in 64bit
kernel.
--------------------------------------
root@qemux86-64:~# arptables -P INPUT ACCEPT
root@qemux86-64:~# arptables -P INPUT ACCEPT
ERROR: Policy for `INPUT' offset 448 != underflow 0
arptables: Incompatible with this kernel
--------------------------------------
Fixes:
09d9686047db ("netfilter: x_tables: do compat validation via translate_table")
Signed-off-by: Hongxu Jia <hongxu.jia@windriver.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Westphal [Thu, 14 Jul 2016 15:51:26 +0000 (17:51 +0200)]
netfilter: x_tables: speed up jump target validation
commit
f4dc77713f8016d2e8a3295e1c9c53a21f296def upstream.
The dummy ruleset I used to test the original validation change was broken,
most rules were unreachable and were not tested by mark_source_chains().
In some cases rulesets that used to load in a few seconds now require
several minutes.
sample ruleset that shows the behaviour:
echo "*filter"
for i in $(seq 0 100000);do
printf ":chain_%06x - [0:0]\n" $i
done
for i in $(seq 0 100000);do
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
done
echo COMMIT
[ pipe result into iptables-restore ]
This ruleset will be about 74mbyte in size, with ~500k searches
though all 500k[1] rule entries. iptables-restore will take forever
(gave up after 10 minutes)
Instead of always searching the entire blob for a match, fill an
array with the start offsets of every single ipt_entry struct,
then do a binary search to check if the jump target is present or not.
After this change ruleset restore times get again close to what one
gets when reverting
36472341017529e (~3 seconds on my workstation).
[1] every user-defined rule gets an implicit RETURN, so we get
300k jumps + 100k userchains + 100k returns -> 500k rule entries
Fixes:
36472341017529e ("netfilter: x_tables: validate targets of jumps")
Reported-by: Jeff Wu <wujiafu@gmail.com>
Tested-by: Jeff Wu <wujiafu@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seunghun Han [Wed, 26 Apr 2017 08:18:08 +0000 (16:18 +0800)]
ACPICA: Namespace: fix operand cache leak
commit
3b2d69114fefa474fca542e51119036dceb4aa6f upstream.
ACPICA commit
a23325b2e583556eae88ed3f764e457786bf4df6
I found some ACPI operand cache leaks in ACPI early abort cases.
Boot log of ACPI operand cache leak is as follows:
>[ 0.174332] ACPI: Added _OSI(Module Device)
>[ 0.175504] ACPI: Added _OSI(Processor Device)
>[ 0.176010] ACPI: Added _OSI(3.0 _SCP Extensions)
>[ 0.177032] ACPI: Added _OSI(Processor Aggregator Device)
>[ 0.178284] ACPI: SCI (IRQ16705) allocation failed
>[ 0.179352] ACPI Exception: AE_NOT_ACQUIRED, Unable to install
System Control Interrupt handler (
20160930/evevent-131)
>[ 0.180008] ACPI: Unable to start the ACPI Interpreter
>[ 0.181125] ACPI Error: Could not remove SCI handler
(
20160930/evmisc-281)
>[ 0.184068] kmem_cache_destroy Acpi-Operand: Slab cache still has
objects
>[ 0.185358] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.10.0-rc3 #2
>[ 0.186820] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
>[ 0.188000] Call Trace:
>[ 0.188000] ? dump_stack+0x5c/0x7d
>[ 0.188000] ? kmem_cache_destroy+0x224/0x230
>[ 0.188000] ? acpi_sleep_proc_init+0x22/0x22
>[ 0.188000] ? acpi_os_delete_cache+0xa/0xd
>[ 0.188000] ? acpi_ut_delete_caches+0x3f/0x7b
>[ 0.188000] ? acpi_terminate+0x5/0xf
>[ 0.188000] ? acpi_init+0x288/0x32e
>[ 0.188000] ? __class_create+0x4c/0x80
>[ 0.188000] ? video_setup+0x7a/0x7a
>[ 0.188000] ? do_one_initcall+0x4e/0x1b0
>[ 0.188000] ? kernel_init_freeable+0x194/0x21a
>[ 0.188000] ? rest_init+0x80/0x80
>[ 0.188000] ? kernel_init+0xa/0x100
>[ 0.188000] ? ret_from_fork+0x25/0x30
When early abort is occurred due to invalid ACPI information, Linux kernel
terminates ACPI by calling acpi_terminate() function. The function calls
acpi_ns_terminate() function to delete namespace data and ACPI operand cache
(acpi_gbl_module_code_list).
But the deletion code in acpi_ns_terminate() function is wrapped in
ACPI_EXEC_APP definition, therefore the code is only executed when the
definition exists. If the define doesn't exist, ACPI operand cache
(acpi_gbl_module_code_list) is leaked, and stack dump is shown in kernel log.
This causes a security threat because the old kernel (<= 4.9) shows memory
locations of kernel functions in stack dump, therefore kernel ASLR can be
neutralized.
To fix ACPI operand leak for enhancing security, I made a patch which
removes the ACPI_EXEC_APP define in acpi_ns_terminate() function for
executing the deletion code unconditionally.
Link: https://github.com/acpica/acpica/commit/a23325b2
Signed-off-by: Seunghun Han <kkamagui@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Fri, 30 Dec 2016 01:27:31 +0000 (02:27 +0100)]
ACPI / scan: Prefer devices without _HID/_CID for _ADR matching
commit
c2a6bbaf0c5f90463a7011a295bbdb7e33c80b51 upstream.
The way acpi_find_child_device() works currently is that, if there
are two (or more) devices with the same _ADR value in the same
namespace scope (which is not specifically allowed by the spec and
the OS behavior in that case is not defined), the first one of them
found to be present (with the help of _STA) will be returned.
This covers the majority of cases, but is not sufficient if some of
the devices in question have a _HID (or _CID) returning some valid
ACPI/PNP device IDs (which is disallowed by the spec) and the
ASL writers' expectation appears to be that the OS will match
devices without a valid ACPI/PNP device ID against a given bus
address first.
To cover this special case as well, modify find_child_checks()
to prefer devices without ACPI/PNP device IDs over devices that
have them.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Wed, 1 Jun 2016 23:57:50 +0000 (01:57 +0200)]
ACPI / processor: Avoid reserving IO regions too early
commit
86314751c7945fa0c67f459beeda2e7c610ca429 upstream.
Roland Dreier reports that one of his systems cannot boot because of
the changes made by commit
ac212b6980d8 (ACPI / processor: Use common
hotplug infrastructure).
The problematic part of it is the request_region() call in
acpi_processor_get_info() that used to run at module init time before
the above commit and now it runs much earlier. Unfortunately, the
region(s) reserved by it fall into a range the PCI subsystem attempts
to reserve for AHCI IO BARs. As a result, the PCI reservation fails
and AHCI doesn't work, while previously the PCI reservation would
be made before acpi_processor_get_info() and it would succeed.
That request_region() call, however, was overlooked by commit
ac212b6980d8, as it is not necessary for the enumeration of the
processors. It only is needed when the ACPI processor driver
actually attempts to handle them which doesn't happen before
loading the ACPI processor driver module. Therefore that call
should have been moved from acpi_processor_get_info() into that
module.
Address the problem by moving the request_region() call in question
out of acpi_processor_get_info() and use the observation that the
region reserved by it is only needed if the FADT-based CPU
throttling method is going to be used, which means that it should
be sufficient to invoke it from acpi_processor_get_throttling_fadt().
Fixes:
ac212b6980d8 (ACPI / processor: Use common hotplug infrastructure)
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rui Wang [Wed, 8 Jun 2016 06:59:52 +0000 (14:59 +0800)]
x86/ioapic: Fix incorrect pointers in ioapic_setup_resources()
commit
9d98bcec731756b8688b59ec998707924d716d7b upstream.
On a 4-socket Brickland system, hot-removing one ioapic is fine.
Hot-removing the 2nd one causes panic in mp_unregister_ioapic()
while calling release_resource().
It is because the iomem_res pointer has already been released
when removing the first ioapic.
To explain the use of &res[num] here: res is assigned to ioapic_resources,
and later in ioapic_insert_resources() we do:
struct resource *r = ioapic_resources;
for_each_ioapic(i) {
insert_resource(&iomem_resource, r);
r++;
}
Here 'r' is treated as an arry of 'struct resource', and the r++ ensures
that each element of the array is inserted separately. Thus we should call
release_resouce() on each element at &res[num].
Fix it by assigning the correct pointers to ioapics[i].iomem_res in
ioapic_setup_resources().
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: tony.luck@intel.com
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1465369193-4816-3-git-send-email-rui.y.wang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Wed, 14 Dec 2016 23:06:07 +0000 (15:06 -0800)]
ipc: msg, make msgrcv work with LONG_MIN
commit
999898355e08ae3b92dfd0a08db706e0c6703d30 upstream.
When LONG_MIN is passed to msgrcv, one would expect to recieve any
message. But convert_mode does *msgtyp = -*msgtyp and -LONG_MIN is
undefined. In particular, with my gcc -LONG_MIN produces -LONG_MIN
again.
So handle this case properly by assigning LONG_MAX to *msgtyp if
LONG_MIN was specified as msgtyp to msgrcv.
This code:
long msg[] = { 100, 200 };
int m = msgget(IPC_PRIVATE, IPC_CREAT | 0644);
msgsnd(m, &msg, sizeof(msg), 0);
msgrcv(m, &msg, sizeof(msg), LONG_MIN, 0);
produces currently nothing:
msgget(IPC_PRIVATE, IPC_CREAT|0644) = 65538
msgsnd(65538, {100, "\310\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"}, 16, 0) = 0
msgrcv(65538, ...
Except a UBSAN warning:
UBSAN: Undefined behaviour in ipc/msg.c:745:13
negation of -
9223372036854775808 cannot be represented in type 'long int':
With the patch, I see what I expect:
msgget(IPC_PRIVATE, IPC_CREAT|0644) = 0
msgsnd(0, {100, "\310\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"}, 16, 0) = 0
msgrcv(0, {100, "\310\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"}, 16, -
9223372036854775808, 0) = 16
Link: http://lkml.kernel.org/r/20161024082633.10148-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vlastimil Babka [Thu, 16 Nov 2017 01:38:30 +0000 (17:38 -0800)]
mm, page_alloc: fix potential false positive in __zone_watermark_ok
commit
b050e3769c6b4013bb937e879fc43bf1847ee819 upstream.
Since commit
97a16fc82a7c ("mm, page_alloc: only enforce watermarks for
order-0 allocations"), __zone_watermark_ok() check for high-order
allocations will shortcut per-migratetype free list checks for
ALLOC_HARDER allocations, and return true as long as there's free page
of any migratetype. The intention is that ALLOC_HARDER can allocate
from MIGRATE_HIGHATOMIC free lists, while normal allocations can't.
However, as a side effect, the watermark check will then also return
true when there are pages only on the MIGRATE_ISOLATE list, or (prior to
CMA conversion to ZONE_MOVABLE) on the MIGRATE_CMA list. Since the
allocation cannot actually obtain isolated pages, and might not be able
to obtain CMA pages, this can result in a false positive.
The condition should be rare and perhaps the outcome is not a fatal one.
Still, it's better if the watermark check is correct. There also
shouldn't be a performance tradeoff here.
Link: http://lkml.kernel.org/r/20171102125001.23708-1-vbabka@suse.cz
Fixes:
97a16fc82a7c ("mm, page_alloc: only enforce watermarks for order-0 allocations")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doug Berger [Mon, 10 Jul 2017 22:49:44 +0000 (15:49 -0700)]
cma: fix calculation of aligned offset
commit
e048cb32f69038aa1c8f11e5c1b331be4181659d upstream.
The align_offset parameter is used by bitmap_find_next_zero_area_off()
to represent the offset of map's base from the previous alignment
boundary; the function ensures that the returned index, plus the
align_offset, honors the specified align_mask.
The logic introduced by commit
b5be83e308f7 ("mm: cma: align to physical
address, not CMA region position") has the cma driver calculate the
offset to the *next* alignment boundary. In most cases, the base
alignment is greater than that specified when making allocations,
resulting in a zero offset whether we align up or down. In the example
given with the commit, the base alignment (8MB) was half the requested
alignment (16MB) so the math also happened to work since the offset is
8MB in both directions. However, when requesting allocations with an
alignment greater than twice that of the base, the returned index would
not be correctly aligned.
Also, the align_order arguments of cma_bitmap_aligned_mask() and
cma_bitmap_aligned_offset() should not be negative so the argument type
was made unsigned.
Fixes:
b5be83e308f7 ("mm: cma: align to physical address, not CMA region position")
Link: http://lkml.kernel.org/r/20170628170742.2895-1-opendmb@gmail.com
Signed-off-by: Angus Clark <angus@angusclark.org>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Cc: Doug Berger <opendmb@gmail.com>
Cc: Angus Clark <angus@angusclark.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Shiraz Hashim <shashim@codeaurora.org>
Cc: Jaewon Kim <jaewon31.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Hocko [Fri, 12 May 2017 22:46:26 +0000 (15:46 -0700)]
hwpoison, memcg: forcibly uncharge LRU pages
commit
18365225f0440d09708ad9daade2ec11275c3df9 upstream.
Laurent Dufour has noticed that hwpoinsoned pages are kept charged. In
his particular case he has hit a bad_page("page still charged to
cgroup") when onlining a hwpoison page. While this looks like something
that shouldn't happen in the first place because onlining hwpages and
returning them to the page allocator makes only little sense it shows a
real problem.
hwpoison pages do not get freed usually so we do not uncharge them (at
least not since commit
0a31bc97c80c ("mm: memcontrol: rewrite uncharge
API")). Each charge pins memcg (since
e8ea14cc6ead ("mm: memcontrol:
take a css reference for each charged page")) as well and so the
mem_cgroup and the associated state will never go away. Fix this leak
by forcibly uncharging a LRU hwpoisoned page in delete_from_lru_cache().
We also have to tweak uncharge_list because it cannot rely on zero ref
count for these pages.
[akpm@linux-foundation.org: coding-style fixes]
Fixes:
0a31bc97c80c ("mm: memcontrol: rewrite uncharge API")
Link: http://lkml.kernel.org/r/20170502185507.GB19165@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Hocko [Mon, 10 Jul 2017 22:49:51 +0000 (15:49 -0700)]
mm/mmap.c: do not blow on PROT_NONE MAP_FIXED holes in the stack
commit
561b5e0709e4a248c67d024d4d94b6e31e3edf2f upstream.
Commit
1be7107fbe18 ("mm: larger stack guard gap, between vmas") has
introduced a regression in some rust and Java environments which are
trying to implement their own stack guard page. They are punching a new
MAP_FIXED mapping inside the existing stack Vma.
This will confuse expand_{downwards,upwards} into thinking that the
stack expansion would in fact get us too close to an existing non-stack
vma which is a correct behavior wrt safety. It is a real regression on
the other hand.
Let's work around the problem by considering PROT_NONE mapping as a part
of the stack. This is a gros hack but overflowing to such a mapping
would trap anyway an we only can hope that usespace knows what it is
doing and handle it propely.
Fixes:
1be7107fbe18 ("mm: larger stack guard gap, between vmas")
Link: http://lkml.kernel.org/r/20170705182849.GA18027@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vlastimil Babka [Tue, 11 Oct 2016 20:51:14 +0000 (13:51 -0700)]
fs/select: add vmalloc fallback for select(2)
commit
2d19309cf86883f634a4f8ec55a54bda87db19bf upstream.
The select(2) syscall performs a kmalloc(size, GFP_KERNEL) where size grows
with the number of fds passed. We had a customer report page allocation
failures of order-4 for this allocation. This is a costly order, so it might
easily fail, as the VM expects such allocation to have a lower-order fallback.
Such trivial fallback is vmalloc(), as the memory doesn't have to be physically
contiguous and the allocation is temporary for the duration of the syscall
only. There were some concerns, whether this would have negative impact on the
system by exposing vmalloc() to userspace. Although an excessive use of vmalloc
can cause some system wide performance issues - TLB flushes etc. - a large
order allocation is not for free either and an excessive reclaim/compaction can
have a similar effect. Also note that the size is effectively limited by
RLIMIT_NOFILE which defaults to 1024 on the systems I checked. That means the
bitmaps will fit well within single page and thus the vmalloc() fallback could
be only excercised for processes where root allows a higher limit.
Note that the poll(2) syscall seems to use a linked list of order-0 pages, so
it doesn't need this kind of fallback.
[eric.dumazet@gmail.com: fix failure path logic]
[akpm@linux-foundation.org: use proper type for size]
Link: http://lkml.kernel.org/r/20160927084536.5923-1-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
yangbo lu [Wed, 25 Nov 2015 02:05:37 +0000 (10:05 +0800)]
mmc: sdhci-of-esdhc: add/remove some quirks according to vendor version
commit
1ef5e49e46b919052474d9b54a15debc79ff0133 upstream.
A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
u32 vvn;
vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
if (vvn == VENDOR_V_22)
host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
if (vvn > VENDOR_V_22)
host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}
This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Fixes:
f4932cfd22f1 ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minghuan Lian [Mon, 29 Feb 2016 23:24:15 +0000 (17:24 -0600)]
PCI: layerscape: Fix MSG TLP drop setting
commit
1195c103f6c98d9ff381cac3a8760d4f8a133627 upstream.
Some kinds of Layerscape PCIe controllers will forward the received message
TLPs to system application address space, which could corrupt system memory
or lead to a system hang. Enable MSG_DROP to fix this issue.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>