OSDN Git Service
Martin K. Petersen [Wed, 16 Jan 2019 00:49:59 +0000 (16:49 -0800)]
scsi: sd: Simplify misaligned I/O check
Avoid open coding the checks for the supported logical block sizes and use
a mask to check for misaligned I/O. Use our helper functions to scale lba
and block count.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin K. Petersen [Wed, 16 Jan 2019 00:49:58 +0000 (16:49 -0800)]
scsi: sd: Be consistent about blocks vs. sectors
We have had several bugs due mixing sector and logical block size
terminology. In the block layer, a sector is a 512-byte unit regardless of
the logical block size of the underlying device. But the term "sector" is
still widely used in sd.c when referring to logical block sized units.
We previously introduced helper functions such as sectors_to_logical() and
logical_to_sectors() to make the distinction clear. Use these to make the
code in sd.c consistent wrt. logical blocks and block layer sectors.
Use "lba" to describe a logical block address and "nr_blocks" when counting
logical blocks. SBC uses "TRANSFER LENGTH" to describe the latter but this
term was avoided to prevent confusion with the very similar DMA transfer
size (->transfersize) which is counted in bytes.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Wed, 16 Jan 2019 00:49:57 +0000 (16:49 -0800)]
scsi: sd: Remove a local variable
This patch does not change any functionality.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Evan Green [Fri, 11 Jan 2019 23:31:59 +0000 (15:31 -0800)]
scsi: ufs: Remove select of phy-qcom-ufs from ufs-qcom
CONFIG_SCSI_UFS_QCOM selects CONFIG_PHY_QCOM_UFS, assuming that this was
the only possible PHY driver Qualcomm's UFS controller would use. But in
SDM845, the UFS driver is bundled into phy-qcom-qmp, and phy-qcom-ufs is
unused.
Remove the select, since for SDM845 it adds useless drivers to the build.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Otto Sabart [Wed, 9 Jan 2019 19:08:56 +0000 (20:08 +0100)]
scsi: doc: remove reference to tmscsim.txt file
The tmscsim.txt doc file was removed in
c121107d0f84.
Fixes:
c121107d0f84 ("scsi: documentation: Obsolete documentation references")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Fri, 4 Jan 2019 16:01:28 +0000 (00:01 +0800)]
scsi: libsas: Support SATA PHY connection rate unmatch fixing during discovery
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Fri, 4 Jan 2019 16:01:27 +0000 (00:01 +0800)]
scsi: libsas: Check SMP PHY control function result
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Fri, 4 Jan 2019 16:01:26 +0000 (00:01 +0800)]
scsi: libsas: Fix some indentation in libsas.h
Currently much indentation in this file is done with whitespaces instead of
tabs, which can make reading difficult, so fix this up.
Some other little minor tidy-up is done, but this file still has many other
checkpatch warnings (generally linelength > 80 or function arguments have
no identifier names).
All libsas code can be audited for checkpatch issues later.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Giridhar Malavali [Fri, 21 Dec 2018 17:33:45 +0000 (09:33 -0800)]
scsi: qla2xxx: Fix DMA error when the DIF sg buffer crosses 4GB boundary
When SGE buffer containing DIF information crosses 4G boundary, it results
in DMA error. This patch fixes this issue by calculating SGE buffer size
and if it crosses 4G boundary, driver will split it into multiple SGE
buffers to avoid DMA error.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin K. Petersen [Fri, 21 Dec 2018 17:33:44 +0000 (09:33 -0800)]
scsi: qla2xxx: Add protection mask module parameters
Allow user to selectively enable/disable DIF/DIX protection
capabilities mask.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 28 Nov 2018 04:26:19 +0000 (22:26 -0600)]
scsi: aic7xxx: aic79xx: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in some cases, I replaced "FALLTHROUGH" with a "fall through"
annotation and then placed it at the bottom of the corresponding switch
case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 114961 ("Missing break in switch")
Addresses-Coverity-ID: 114962 ("Missing break in switch")
Addresses-Coverity-ID: 114963 ("Missing break in switch")
Addresses-Coverity-ID: 114964 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 28 Nov 2018 04:27:32 +0000 (22:27 -0600)]
scsi: bfa: bfa_ioc: Mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
comment with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 146155 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 28 Nov 2018 04:27:23 +0000 (22:27 -0600)]
scsi: bfa: bfa_fcs_rport: Mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that I replaced "!! fall through !!" and "!!! fall through !!!"
comments with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 744899 ("Missing break in switch")
Addresses-Coverity-ID: 744900 ("Missing break in switch")
Addresses-Coverity-ID: 744901 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 28 Nov 2018 04:27:15 +0000 (22:27 -0600)]
scsi: bfa: bfa_fcs_lport: Mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
with a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 28 Nov 2018 04:28:57 +0000 (22:28 -0600)]
scsi: esas2r: esas2r_init: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bradley Grove <bgrove@atto.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 28 Nov 2018 04:33:54 +0000 (22:33 -0600)]
scsi: st: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 114994 ("Missing break in switch")
Addresses-Coverity-ID: 114995 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gustavo A. R. Silva [Wed, 28 Nov 2018 04:33:43 +0000 (22:33 -0600)]
scsi: qla4xxx: ql4_os: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "allow fall-through" with
a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Fri, 4 Jan 2019 17:02:24 +0000 (17:02 +0000)]
scsi: bnx2i: fix indentation issue, remove a tab
The return statement is indented incorrectly, fix this by removing a single
tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 8 Jan 2019 15:14:52 +0000 (23:14 +0800)]
scsi: sd: Make protection lookup tables static and relocate functions
Currently the protection lookup tables in sd_prot_flag_mask() and
sd_prot_op() are declared as non-static. As such, they will be rebuilt for
each respective function call.
Optimise by making them static.
This saves ~100B object code for sd.c:
Before:
text data bss dec hex filename
25403 1024 16 26443 674b drivers/scsi/sd.o
After:
text data bss dec hex filename
25299 1024 16 26339 66e3 drivers/scsi/sd.o
In addition, since those same functions are declared in sd.h, but each are
only referenced in sd.c, relocate them to that same c file.
The inline specifier is dropped also, since gcc should be able to make the
decision to inline.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:46 +0000 (23:56 +0800)]
scsi: hisi_sas: Add debugfs IOST file and add file operations
This patch create debugfs file for IOST and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:45 +0000 (23:56 +0800)]
scsi: hisi_sas: Add debugfs DQ file and add file operations
This patch create debugfs file for DQ and add file operations
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:44 +0000 (23:56 +0800)]
scsi: hisi_sas: Add debugfs CQ file and add file operations
This patch create debugfs file for CQ and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:43 +0000 (23:56 +0800)]
scsi: hisi_sas: Add debugfs for port registers
This patch create debugfs file for port register and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:42 +0000 (23:56 +0800)]
scsi: hisi_sas: Debugfs global register create file and add file operations
This patch create debugfs file for global register and add file
operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:41 +0000 (23:56 +0800)]
scsi: hisi_sas: Take debugfs snapshot for all regs
This patch takes snapshot for global regs, port regs, CQ, DQ, IOST, ITCT.
Add code for snapshot trig and generate dump directory.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:40 +0000 (23:56 +0800)]
scsi: hisi_sas: Alloc debugfs snapshot buffer memory for all registers
This patch allocates snapshot memory for global reg, port regs, CQ, DQ,
IOST, ITCT.
When we fail to allocate memory for some registers, we free the memory
and set hisi_sas_debugfs_enable as 0 to stop loading debugfs from running.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Wed, 19 Dec 2018 15:56:39 +0000 (23:56 +0800)]
scsi: hisi_sas: Create root and device debugfs directories
This patch creates root directory at hisi_sas_init() and generates device
directory when we probe device driver.
And we remove the root directory at hisi_sas_exit(), but recursively
delete device directory when we remove device driver.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 09:02:08 +0000 (17:02 +0800)]
scsi: arcmsr: Update driver version to v1.40.00.10-
20181217
From Ching Huang <ching2048@areca.com.tw>
Update driver version to v1.40.00.10-
20181217
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:59:48 +0000 (16:59 +0800)]
scsi: arcmsr: Fix suspend/resume of ACB_ADAPTER_TYPE_B
From Ching Huang <ching2048@areca.com.tw>
Fix suspend/resume of ACB_ADAPTER_TYPE_B
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:56:34 +0000 (16:56 +0800)]
scsi: arcmsr: Separate 'set dma mask' as a function
From Ching Huang <ching2048@areca.com.tw>
Separate 'set dma mask' as a function
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:53:44 +0000 (16:53 +0800)]
scsi: arcmsr: Add an option of set dma_mask_64 for ACB_ADAPTER_TYPE_A
From Ching Huang <ching2048@areca.com.tw>
Add an option of set dma_mask_64 for ACB_ADAPTER_TYPE_A
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:51:14 +0000 (16:51 +0800)]
scsi: arcmsr: Update ACB_ADAPTER_TYPE_D for >4GB ccb addressing
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_D for >4gb ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:48:16 +0000 (16:48 +0800)]
scsi: arcmsr: Update ACB_ADAPTER_TYPE_C for >4GB ccb addressing
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_C for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:45:46 +0000 (16:45 +0800)]
scsi: arcmsr: Update ACB_ADAPTER_TYPE_B for >4GB ccb addressing
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_B for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:43:15 +0000 (16:43 +0800)]
scsi: arcmsr: Update ACB_ADAPTER_TYPE_A for >4GB ccb addressing
From Ching Huang <ching2048@areca.com.tw>
Update ACB_ADAPTER_TYPE_A for >4GB ccb addressing
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:34:58 +0000 (16:34 +0800)]
scsi: arcmsr: Update arcmsr_alloc_ccb_pool for ccb buffer address above 4GB
From Ching Huang <ching2048@areca.com.tw>
Update arcmsr_alloc_ccb_pool for ccb buffer address above 4GB
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:31:00 +0000 (16:31 +0800)]
scsi: arcmsr: Merge arcmsr_alloc_io_queue to arcmsr_alloc_ccb_pool
From Ching Huang <ching2048@areca.com.tw>
Merge arcmsr_alloc_io_queue to arcmsr_alloc_ccb_pool
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:27:20 +0000 (16:27 +0800)]
scsi: arcmsr: Rename arcmsr_free_mu to arcmsr_free_io_queue
From Ching Huang <ching2048@areca.com.tw>
Rename arcmsr_free_mu to arcmsr_free_io_queue
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Dec 2018 08:24:03 +0000 (16:24 +0800)]
scsi: arcmsr: Rename acb structure member roundup_ccbsize to ioqueue_size
From Ching Huang <ching2048@areca.com.tw>
Rename acb structure member roundup_ccbsize to ioqueue_size
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:27 +0000 (08:41 +0100)]
scsi: gdth: use generic DMA API
Switch from the legacy PCI DMA API to the generic DMA API. Also switch
to dma_map_single from pci_map_page in one case where this makes the code
simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:26 +0000 (08:41 +0100)]
scsi: gdth: remove interrupt coalescing support
This code has been under a never defined ifdef since the beginning
of time (or at least history), and has just bitrotted. Nuke it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:25 +0000 (08:41 +0100)]
scsi: gdth: remove dead code under #ifdef GDTH_IOCTL_PROC
This can't ever be compiled into the kernel, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:24 +0000 (08:41 +0100)]
scsi: gdth: remove dead dma statistics code
This code can't be built into the kernel without editing the source
file and is not generally useful.
[mkp: typo]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:23 +0000 (08:41 +0100)]
scsi: gdth: remove dead rtc code
This code has been under the never defined GDTH_RTC ifdef forever,
nuke it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:22 +0000 (08:41 +0100)]
scsi: gdth: remove direct serial port access
Remove never compile in support for sending debug traces straight to
the serial port using direct port access.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:21 +0000 (08:41 +0100)]
scsi: gdth: remove ISA and EISA support
The non-PCI code has bitrotted for quite a while and will just oops
on load because it passes a NULL pointer to the PCI DMA routines.
Lets kill it for good - if someone really wants to use one of these
cards I'll help mentoring them to write a proper driver glue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:20 +0000 (08:41 +0100)]
scsi: gdth: remove gdth_{alloc,free}_ioctl
Out of the three callers once insists on the scratch buffer, and the
others are fine with a new allocation. Switch those two to just use
pci_alloc_consistent directly, and open code the scratch buffer
allocation in the remaining one. This avoids a case where we might
be doing a memory allocation under a spinlock with irqs disabled.
[mkp: typo]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:19 +0000 (08:41 +0100)]
scsi: gdth: reuse dma coherent allocation in gdth_show_info
gdth_show_info currently allocs and frees a dma buffer four times which
isn't very efficient. Reuse a single allocation instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Wed, 12 Dec 2018 07:41:18 +0000 (08:41 +0100)]
scsi: gdth: refactor ioc_general
This function is a huge mess with duplicated error handling. Split out
a few useful helpers and use goto labels to untangle the error handling
and no-data ioctl handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linus Torvalds [Mon, 7 Jan 2019 01:08:20 +0000 (17:08 -0800)]
Linux 5.0-rc1
Linus Torvalds [Mon, 7 Jan 2019 00:33:10 +0000 (16:33 -0800)]
Merge tag 'kbuild-v4.21-3' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Linus Torvalds [Mon, 7 Jan 2019 00:30:14 +0000 (16:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tooling updates form Ingo Molnar:
"A final batch of perf tooling changes: mostly fixes and small
improvements"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
perf session: Add comment for perf_session__register_idle_thread()
perf thread-stack: Fix thread stack processing for the idle task
perf thread-stack: Allocate an array of thread stacks
perf thread-stack: Factor out thread_stack__init()
perf thread-stack: Allow for a thread stack array
perf thread-stack: Avoid direct reference to the thread's stack
perf thread-stack: Tidy thread_stack__bottom() usage
perf thread-stack: Simplify some code in thread_stack__process()
tools gpio: Allow overriding CFLAGS
tools power turbostat: Override CFLAGS assignments and add LDFLAGS to build command
tools thermal tmon: Allow overriding CFLAGS assignments
tools power x86_energy_perf_policy: Override CFLAGS assignments and add LDFLAGS to build command
perf c2c: Increase the HITM ratio limit for displayed cachelines
perf c2c: Change the default coalesce setup
perf trace beauty ioctl: Beautify USBDEVFS_ commands
perf trace beauty: Export function to get the files for a thread
perf trace: Wire up ioctl's USBDEBFS_ cmd table generator
perf beauty ioctl: Add generator for USBDEVFS_ ioctl commands
tools headers uapi: Grab a copy of usbdevice_fs.h
perf trace: Store the major number for a file when storing its pathname
...
Linus Torvalds [Sun, 6 Jan 2019 01:50:59 +0000 (17:50 -0800)]
Change mincore() to count "mapped" pages rather than "cached" pages
The semantics of what "in core" means for the mincore() system call are
somewhat unclear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache" rather than "page is mapped in the mapping".
The problem with that traditional semantic is that it exposes a lot of
system cache state that it really probably shouldn't, and that users
shouldn't really even care about.
So let's try to avoid that information leak by simply changing the
semantics to be that mincore() counts actual mapped pages, not pages
that might be cheaply mapped if they were faulted (note the "might be"
part of the old semantics: being in the cache doesn't actually guarantee
that you can access them without IO anyway, since things like network
filesystems may have to revalidate the cache before use).
In many ways the old semantics were somewhat insane even aside from the
information leak issue. From the very beginning (and that beginning is
a long time ago: 2.3.52 was released in March 2000, I think), the code
had a comment saying
Later we can get more picky about what "in core" means precisely.
and this is that "later". Admittedly it is much later than is really
comfortable.
NOTE! This is a real semantic change, and it is for example known to
change the output of "fincore", since that program literally does a
mmmap without populating it, and then doing "mincore()" on that mapping
that doesn't actually have any pages in it.
I'm hoping that nobody actually has any workflow that cares, and the
info leak is real.
We may have to do something different if it turns out that people have
valid reasons to want the old semantics, and if we can limit the
information leak sanely.
Cc: Kevin Easton <kevin@guarana.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Masatake YAMATO <yamato@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 19:15:04 +0000 (11:15 -0800)]
Fix 'acccess_ok()' on alpha and SH
Commit
594cc251fdd0 ("make 'user_access_begin()' do 'access_ok()'")
broke both alpha and SH booting in qemu, as noticed by Guenter Roeck.
It turns out that the bug wasn't actually in that commit itself (which
would have been surprising: it was mostly a no-op), but in how the
addition of access_ok() to the strncpy_from_user() and strnlen_user()
functions now triggered the case where those functions would test the
access of the very last byte of the user address space.
The string functions actually did that user range test before too, but
they did it manually by just comparing against user_addr_max(). But
with user_access_begin() doing the check (using "access_ok()"), it now
exposed problems in the architecture implementations of that function.
For example, on alpha, the access_ok() helper macro looked like this:
#define __access_ok(addr, size) \
((get_fs().seg & (addr | size | (addr+size))) == 0)
and what it basically tests is of any of the high bits get set (the
USER_DS masking value is 0xfffffc0000000000).
And that's completely wrong for the "addr+size" check. Because it's
off-by-one for the case where we check to the very end of the user
address space, which is exactly what the strn*_user() functions do.
Why? Because "addr+size" will be exactly the size of the address space,
so trying to access the last byte of the user address space will fail
the __access_ok() check, even though it shouldn't. As a result, the
user string accessor functions failed consistently - because they
literally don't know how long the string is going to be, and the max
access is going to be that last byte of the user address space.
Side note: that alpha macro is buggy for another reason too - it re-uses
the arguments twice.
And SH has another version of almost the exact same bug:
#define __addr_ok(addr) \
((unsigned long __force)(addr) < current_thread_info()->addr_limit.seg)
so far so good: yes, a user address must be below the limit. But then:
#define __access_ok(addr, size) \
(__addr_ok((addr) + (size)))
is wrong with the exact same off-by-one case: the case when "addr+size"
is exactly _equal_ to the limit is actually perfectly fine (think "one
byte access at the last address of the user address space")
The SH version is actually seriously buggy in another way: it doesn't
actually check for overflow, even though it did copy the _comment_ that
talks about overflow.
So it turns out that both SH and alpha actually have completely buggy
implementations of access_ok(), but they happened to work in practice
(although the SH overflow one is a serious serious security bug, not
that anybody likely cares about SH security).
This fixes the problems by using a similar macro on both alpha and SH.
It isn't trying to be clever, the end address is based on this logic:
unsigned long __ao_end = __ao_a + __ao_b - !!__ao_b;
which basically says "add start and length, and then subtract one unless
the length was zero". We can't subtract one for a zero length, or we'd
just hit an underflow instead.
For a lot of access_ok() users the length is a constant, so this isn't
actually as expensive as it initially looks.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 20:21:11 +0000 (12:21 -0800)]
Merge tag 'fscrypt_for_linus' of git://git./linux/kernel/git/tytso/fscrypt
Pull fscrypt updates from Ted Ts'o:
"Add Adiantum support for fscrypt"
* tag 'fscrypt_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: add Adiantum support
Linus Torvalds [Sun, 6 Jan 2019 20:19:23 +0000 (12:19 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Fix a number of ext4 bugs"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix special inode number checks in __ext4_iget()
ext4: track writeback errors using the generic tracking infrastructure
ext4: use ext4_write_inode() when fsyncing w/o a journal
ext4: avoid kernel warning when writing the superblock to a dead device
ext4: fix a potential fiemap/page fault deadlock w/ inline_data
ext4: make sure enough credits are reserved for dioread_nolock writes
Linus Torvalds [Sun, 6 Jan 2019 19:47:26 +0000 (11:47 -0800)]
Merge tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions introduced in this cycles:
- fix dma-debug tracking for the map_page / map_single
consolidatation
- properly stub out DMA mapping symbols for !HAS_DMA builds to avoid
link failures
- fix AMD Gart direct mappings
- setup the dma address for no kernel mappings using the remap
allocator"
* tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING for remapped allocations
x86/amd_gart: fix unmapping of non-GART mappings
dma-mapping: remove a few unused exports
dma-mapping: properly stub out the DMA API for !CONFIG_HAS_DMA
dma-mapping: remove dmam_{declare,release}_coherent_memory
dma-mapping: implement dmam_alloc_coherent using dmam_alloc_attrs
dma-mapping: implement dma_map_single_attrs using dma_map_page_attrs
Linus Torvalds [Sun, 6 Jan 2019 19:40:06 +0000 (11:40 -0800)]
Merge tag 'tag-chrome-platform-for-v4.21' of git://git./linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- Changes for EC_MKBP_EVENT_SENSOR_FIFO handling.
- Also, maintainership changes. Olofj out, Enric balletbo in.
* tag 'tag-chrome-platform-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
MAINTAINERS: add maintainers for ChromeOS EC sub-drivers
MAINTAINERS: platform/chrome: Add Enric as a maintainer
MAINTAINERS: platform/chrome: remove myself as maintainer
platform/chrome: don't report EC_MKBP_EVENT_SENSOR_FIFO as wakeup
platform/chrome: straighten out cros_ec_get_{next,host}_event() error codes
Linus Torvalds [Sun, 6 Jan 2019 19:37:44 +0000 (11:37 -0800)]
Merge tag 'hwlock-v4.21' of git://github.com/andersson/remoteproc
Pull hwspinlock updates from Bjorn Andersson:
"This adds support for the hardware semaphores found in STM32MP1"
* tag 'hwlock-v4.21' of git://github.com/andersson/remoteproc:
hwspinlock: fix return value check in stm32_hwspinlock_probe()
hwspinlock: add STM32 hwspinlock device
dt-bindings: hwlock: Document STM32 hwspinlock bindings
Eric Biggers [Sun, 6 Jan 2019 13:36:21 +0000 (08:36 -0500)]
fscrypt: add Adiantum support
Add support for the Adiantum encryption mode to fscrypt. Adiantum is a
tweakable, length-preserving encryption mode with security provably
reducible to that of XChaCha12 and AES-256, subject to a security bound.
It's also a true wide-block mode, unlike XTS. See the paper
"Adiantum: length-preserving encryption for entry-level processors"
(https://eprint.iacr.org/2018/720.pdf) for more details. Also see
commit
059c2a4d8e16 ("crypto: adiantum - add Adiantum support").
On sufficiently long messages, Adiantum's bottlenecks are XChaCha12 and
the NH hash function. These algorithms are fast even on processors
without dedicated crypto instructions. Adiantum makes it feasible to
enable storage encryption on low-end mobile devices that lack AES
instructions; currently such devices are unencrypted. On ARM Cortex-A7,
on 4096-byte messages Adiantum encryption is about 4 times faster than
AES-256-XTS encryption; decryption is about 5 times faster.
In fscrypt, Adiantum is suitable for encrypting both file contents and
names. With filenames, it fixes a known weakness: when two filenames in
a directory share a common prefix of >= 16 bytes, with CTS-CBC their
encrypted filenames share a common prefix too, leaking information.
Adiantum does not have this problem.
Since Adiantum also accepts long tweaks (IVs), it's also safe to use the
master key directly for Adiantum encryption rather than deriving
per-file keys, provided that the per-file nonce is included in the IVs
and the master key isn't used for any other encryption mode. This
configuration saves memory and improves performance. A new fscrypt
policy flag is added to allow users to opt-in to this configuration.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Sun, 6 Jan 2019 02:35:02 +0000 (18:35 -0800)]
Merge tag 'docs-5.0-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes"
* tag 'docs-5.0-fixes' of git://git.lwn.net/linux:
doc: filesystems: fix bad references to nonexistent ext4.rst file
Documentation/admin-guide: update URL of LKML information link
Docs/kernel-api.rst: Remove blk-tag.c reference
Linus Torvalds [Sun, 6 Jan 2019 02:33:21 +0000 (18:33 -0800)]
Merge tag 'firewire-update' of git://git./linux/kernel/git/ieee1394/linux1394
Pull firewire fixlet from Stefan Richter:
"Remove an explicit dependency in Kconfig which is implied by another
dependency"
* tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: Remove depends on HAS_DMA in case of platform dependency
Linus Torvalds [Sun, 6 Jan 2019 02:29:13 +0000 (18:29 -0800)]
Merge tag 'for-linus-
20190104' of git://git.kernel.dk/linux-block
Pull block updates and fixes from Jens Axboe:
- Pulled in MD changes that Shaohua had queued up for 4.21.
Unfortunately we lost Shaohua late 2018, I'm sending these in on his
behalf.
- In conjunction with the above, I added a CREDITS entry for Shaoua.
- sunvdc queue restart fix (Ming)
* tag 'for-linus-
20190104' of git://git.kernel.dk/linux-block:
Add CREDITS entry for Shaohua Li
block: sunvdc: don't run hw queue synchronously from irq context
md: fix raid10 hang issue caused by barrier
raid10: refactor common wait code from regular read/write request
md: remvoe redundant condition check
lib/raid6: add option to skip algo benchmarking
lib/raid6: sort algos in rough performance order
lib/raid6: check for assembler SSSE3 support
lib/raid6: avoid __attribute_const__ redefinition
lib/raid6: add missing include for raid6test
md: remove set but not used variable 'bi_rdev'
Linus Torvalds [Sun, 6 Jan 2019 02:25:19 +0000 (18:25 -0800)]
Merge tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Happy New Year, just decloaking from leave to get some stuff from the
last week in before rc1:
core:
- two regression fixes for damage blob and atomic
i915 gvt:
- Some missed GVT fixes from the original pull
amdgpu:
- new PCI IDs
- SR-IOV fixes
- DC fixes
- Vega20 fixes"
* tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm: (53 commits)
drm: Put damage blob when destroy plane state
drm: fix null pointer dereference on null state pointer
drm/amdgpu: Add new VegaM pci id
drm/ttm: Use drm_debug_printer for all ttm_bo_mem_space_debug output
drm/amdgpu: add Vega20 PSP ASD firmware loading
drm/amd/display: Fix MST dp_blank REG_WAIT timeout
drm/amd/display: validate extended dongle caps
drm/amd/display: Use div_u64 for flip timestamp ns to ms
drm/amdgpu/uvd:Change uvd ring name convention
drm/amd/powerplay: add Vega20 LCLK DPM level setting support
drm/amdgpu: print process info when job timeout
drm/amdgpu/nbio7.4: add hw bug workaround for vega20
drm/amdgpu/nbio6.1: add hw bug workaround for vega10/12
drm/amd/display: Optimize passive update planes.
drm/amd/display: verify lane status before exiting verify link cap
drm/amd/display: Fix bug with not updating VSP infoframe
drm/amd/display: Add retry to read ddc_clock pin
drm/amd/display: Don't skip link training for empty dongle
drm/amd/display: Wait edp HPD to high in detect_sink
drm/amd/display: fix surface update sequence
...
Linus Torvalds [Sun, 6 Jan 2019 02:20:51 +0000 (18:20 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Over the break a few defects were found, so this is a -rc style pull
request of various small things that have been posted.
- An attempt to shorten RCU grace period driven delays showed crashes
during heavier testing, and has been entirely reverted
- A missed merge/rebase error between the advise_mr and ib_device_ops
series
- Some small static analysis driven fixes from Julia and Aditya
- Missed ability to create a XRC_INI in the devx verbs interop
series"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
infiniband/qedr: Potential null ptr dereference of qp
infiniband: bnxt_re: qplib: Check the return value of send_message
IB/ipoib: drop useless LIST_HEAD
IB/core: Add advise_mr to the list of known ops
Revert "IB/mlx5: Fix long EEH recover time with NVMe offloads"
IB/mlx5: Allow XRC INI usage via verbs in DEVX context
Linus Torvalds [Sun, 6 Jan 2019 02:15:37 +0000 (18:15 -0800)]
Merge tag 'fbdev-v4.21' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"This time the pull request is really small.
The most notable changes are fixing fbcon to not cause crash on
unregister_framebuffer() operation when there is more than one
framebuffer, adding config option to center the bootup logo and making
FB_BACKLIGHT config option tristate (which in turn uncovered incorrect
FB_BACKLIGHT usage by DRM's nouveau driver).
Summary:
- fix fbcon to not cause crash on unregister_framebuffer() when there
is more than one framebuffer (Noralf Trønnes)
- improve support for small rotated displays (Peter Rosin)
- fix probe failure handling in udlfb driver (Dan Carpenter)
- add config option to center the bootup logo (Peter Rosin)
- make FB_BACKLIGHT config option tristate (Rob Clark)
- remove superfluous HAS_DMA dependency for goldfishfb driver (Geert
Uytterhoeven)
- misc fixes (Alexey Khoroshilov, YueHaibing, Colin Ian King, Lubomir
Rintel)
- misc cleanups (Yangtao Li, Wen Yang)
also there is DRM's nouveau driver fix for wrong FB_BACKLIGHT config
option usage (FB_BACKLIGHT is for internal fbdev subsystem use only)"
* tag 'fbdev-v4.21' of git://github.com/bzolnier/linux:
drm/nouveau: fix incorrect FB_BACKLIGHT usage in Kconfig
fbdev: fbcon: Fix unregister crash when more than one framebuffer
fbdev: Remove depends on HAS_DMA in case of platform dependency
pxa168fb: trivial typo fix
fbdev: fsl-diu: remove redundant null check on cmap
fbdev: omap2: omapfb: convert to DEFINE_SHOW_ATTRIBUTE
fbdev: uvesafb: fix spelling mistake "memoery" -> "memory"
fbdev: fbmem: add config option to center the bootup logo
fbdev: fbmem: make fb_show_logo_line return the end instead of the height
video: fbdev: pxafb: Fix "WARNING: invalid free of devm_ allocated data"
fbdev: fbmem: behave better with small rotated displays and many CPUs
video: clps711x-fb: release disp device node in probe()
fbdev: make FB_BACKLIGHT a tristate
udlfb: fix some inconsistent NULL checking
Linus Torvalds [Sun, 6 Jan 2019 02:13:35 +0000 (18:13 -0800)]
Merge branch 'i2c/for-5.0' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has only driver updates for you this time.
Mostly new IDs/DT compatibles, also SPDX conversions, small cleanups.
STM32F7 got FastMode+ and PM support, Axxia some reliabilty
improvements"
* 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (26 commits)
i2c: Add Actions Semiconductor Owl family S700 I2C support
dt-bindings: i2c: Add S700 support for Actions Semi Soc's
i2c: ismt: Add support for Intel Cedar Fork
i2c: tegra: Switch to SPDX identifier
i2c: tegra: Add missing kerneldoc for some fields
i2c: tegra: Cleanup kerneldoc comments
i2c: axxia: support sequence command mode
dt-bindings: i2c: rcar: Add r8a774c0 support
dt-bindings: i2c: sh_mobile: Add r8a774c0 support
i2c: sh_mobile: Add support for r8a774c0 (RZ/G2E)
i2c: i2c-cros-ec-tunnel: Switch to SPDX identifier.
i2c: powermac: Use of_node_name_eq for node name comparisons
i2c-axxia: check for error conditions first
i2c-axxia: dedicated function to set client addr
dt-bindings: i2c: Use correct vendor prefix for Atmel
i2c: tegra: replace spin_lock_irqsave with spin_lock in ISR
eeprom: at24: add support for
24c2048
dt-bindings: eeprom: at24: add "atmel,
24c2048" compatible string
i2c: i2c-stm32f7: add PM Runtime support
i2c: sh_mobile: add support for r8a77990 (R-Car E3)
...
Linus Torvalds [Sun, 6 Jan 2019 01:57:34 +0000 (17:57 -0800)]
Merge tag 'pci-v4.21-changes' of git://git./linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Remove unused lists from ASPM pcie_link_state (Frederick Lawler)
- Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
King)
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
- Clean up P2PDMA documentation (Randy Dunlap)
- Allow runtime PM even if driver doesn't supply callbacks (Jarkko
Nikula)
- Remove status check after submitting Switchtec MRPC Firmware Download
commands to avoid Completion Timeouts (Kelvin Cao)
- Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)
- Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
(Joey Zhang)
- Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)
- Add Switchtec MRPC DMA mode support (Wesley Sheng)
- Skip VF scanning on powerpc, which does this in firmware (Sebastian
Ott)
- Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)
- Constify histb dw_pcie_host_ops structure (Julia Lawall)
- Support multiple power domains for imx6 (Leonard Crestez)
- Constify layerscape driver data (Stefan Agner)
- Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)
- Support armada8k GPIO reset (Baruch Siach)
- Support suspend/resume support on imx6 (Leonard Crestez)
- Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)
- Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)
- Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)
- Mask DesignWare interrupts instead of disabling them to avoid lost
interrupts (Marc Zyngier)
- Add locking when acking DesignWare interrupts (Marc Zyngier)
- Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)
- Use devm resource parser in mediatek (Honghui Zhang)
- Remove unused mediatek "num-lanes" DT property (Honghui Zhang)
- Add UniPhier PCIe controller driver and DT bindings (Kunihiko
Hayashi)
- Enable MSI for imx6 downstream components (Richard Zhu)
* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
PCI: imx: Enable MSI from downstream components
s390/pci: skip VF scanning
PCI/IOV: Add flag so platforms can skip VF scanning
PCI/IOV: Factor out sriov_add_vfs()
PCI: uniphier: Add UniPhier PCIe host controller support
dt-bindings: PCI: Add UniPhier PCIe host controller description
PCI: amlogic: Add the Amlogic Meson PCIe controller driver
dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
arm64: dts: mt7622: Remove un-used property for PCIe
arm: dts: mt7623: Remove un-used property for PCIe
dt-bindings: PCI: MediaTek: Remove un-used property
PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
PCI: dwc: Don't hard-code DBI/ATU offset
PCI: imx: Add imx6sx suspend/resume support
PCI: armada8k: Add support for gpio controlled reset signal
PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
PCI: dwc: layerscape: Constify driver data
PCI: imx: Add multi-pd support
PCI: Override Synopsys USB 3.x HAPS device class
...
Linus Torvalds [Sun, 6 Jan 2019 01:53:40 +0000 (17:53 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- high-resolution scrolling support that gracefully handles differences
between MS and Logitech implementations in HW, from Peter Hutterer
and Harry Cutts
- MSI IRQ support for intel-ish driver, from Song Hongyan
- support for new hardware (Cougar 700K, Odys Winbook 13, ASUS FX503VD,
ASUS T101HA) from Daniel M. Lambea, Hans de Goede and Aleix Roca
Nonell
- other small assorted fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: i2c-hid: Add Odys Winbook 13 to descriptor override
HID: lenovo: Add checks to fix of_led_classdev_register
HID: intel-ish-hid: add MSI interrupt support
HID: debug: Change to use DEFINE_SHOW_ATTRIBUTE macro
HID: doc: fix wrong data structure reference for UHID_OUTPUT
HID: intel-ish-hid: fixes incorrect error handling
HID: asus: Add support for the ASUS T101HA keyboard dock
HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice
HID: logitech: Enable high-resolution scrolling on Logitech mice
HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration"
HID: logitech-hidpp: fix typo, hiddpp to hidpp
HID: input: use the Resolution Multiplier for high-resolution scrolling
HID: core: process the Resolution Multiplier
HID: core: store the collections as a basic tree
Input: add `REL_WHEEL_HI_RES` and `REL_HWHEEL_HI_RES`
HID: input: support Microsoft wireless radio control hotkey
HID: use macros in IS_INPUT_APPLICATION
HID: asus: Add support for the ASUS FX503VD laptop
HID: asus: Add event handler to catch unmapped Asus Vendor UsagePage codes
HID: cougar: Add support for Cougar 700K Gaming Keyboard
...
Linus Torvalds [Sun, 6 Jan 2019 01:51:36 +0000 (17:51 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/livepatching
Pull livepatch update from Jiri Kosina:
"Return value checking fixup in livepatching samples, from Nicholas Mc
Guire"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: check kzalloc return values
Masahiro Yamada [Sat, 5 Jan 2019 03:01:51 +0000 (12:01 +0900)]
kconfig: rename generated .*conf-cfg to *conf-cfg
Remove the dot-prefixing since it is just a matter of the
.gitignore file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 3 Jan 2019 01:47:05 +0000 (10:47 +0900)]
kbuild: remove unnecessary stubs for archheader and archscripts
Make simply skips a missing rule when it is marked as .PHONY.
Remove the dummy targets.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 3 Jan 2019 01:16:54 +0000 (10:16 +0900)]
kbuild: use assignment instead of define ... endef for filechk_* rules
You do not have to use define ... endef for filechk_* rules.
For simple cases, the use of assignment looks cleaner, IMHO.
I updated the usage for scripts/Kbuild.include in case somebody
misunderstands the 'define ... endif' is the requirement.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Masahiro Yamada [Thu, 3 Jan 2019 01:10:39 +0000 (10:10 +0900)]
arch: remove redundant UAPI generic-y defines
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Thu, 3 Jan 2019 01:10:38 +0000 (10:10 +0900)]
kbuild: generate asm-generic wrappers if mandatory headers are missing
Some time ago, Sam pointed out a certain degree of overwrap between
generic-y and mandatory-y. (https://lkml.org/lkml/2017/7/10/121)
I tweaked the meaning of mandatory-y a little bit; now it defines the
minimum set of ASM headers that all architectures must have.
If arch does not have specific implementation of a mandatory header,
Kbuild will let it fallback to the asm-generic one by automatically
generating a wrapper. This will allow to drop lots of redundant
generic-y defines.
Previously, "mandatory" was used in the context of UAPI, but I guess
this can be extended to kernel space ASM headers.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Thu, 3 Jan 2019 01:10:37 +0000 (10:10 +0900)]
arch: remove stale comments "UAPI Header export list"
These comments are leftovers of commit
fcc8487d477a ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 3 Jan 2019 01:10:36 +0000 (10:10 +0900)]
riscv: remove redundant kernel-space generic-y
This commit removes redundant generic-y defines in
arch/riscv/include/asm/Kbuild.
[1] It is redundant to define the same generic-y in both
arch/$(ARCH)/include/asm/Kbuild and
arch/$(ARCH)/include/uapi/asm/Kbuild.
Remove the following generic-y:
errno.h
fcntl.h
ioctl.h
ioctls.h
ipcbuf.h
mman.h
msgbuf.h
param.h
poll.h
posix_types.h
resource.h
sembuf.h
setup.h
shmbuf.h
signal.h
socket.h
sockios.h
stat.h
statfs.h
swab.h
termbits.h
termios.h
types.h
[2] It is redundant to define generic-y when arch-specific
implementation exists in arch/$(ARCH)/include/asm/*.h
Remove the following generic-y:
cacheflush.h
module.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 31 Dec 2018 08:24:09 +0000 (17:24 +0900)]
kbuild: change filechk to surround the given command with { }
filechk_* rules often consist of multiple 'echo' lines. They must be
surrounded with { } or ( ) to work correctly. Otherwise, only the
string from the last 'echo' would be written into the target.
Let's take care of that in the 'filechk' in scripts/Kbuild.include
to clean up filechk_* rules.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 31 Dec 2018 08:24:08 +0000 (17:24 +0900)]
kbuild: remove redundant target cleaning on failure
Since commit
9c2af1c7377a ("kbuild: add .DELETE_ON_ERROR special
target"), the target file is automatically deleted on failure.
The boilerplate code
... || { rm -f $@; false; }
is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 31 Dec 2018 04:09:00 +0000 (13:09 +0900)]
kbuild: clean up rule_dtc_dt_yaml
Commit
3a2429e1faf4 ("kbuild: change if_changed_rule for multi-line
recipe") and commit
4f0e3a57d6eb ("kbuild: Add support for DT binding
schema checks") came in via different sub-systems.
This is a follow-up cleanup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 31 Dec 2018 01:05:01 +0000 (10:05 +0900)]
kbuild: remove UIMAGE_IN and UIMAGE_OUT
The only/last user of UIMAGE_IN/OUT was removed by commit
4722a3e6b716
("microblaze: fix multiple bugs in arch/microblaze/boot/Makefile").
The input and output should always be $< and $@.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Sun, 30 Dec 2018 15:14:15 +0000 (00:14 +0900)]
jump_label: move 'asm goto' support test to Kconfig
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Mathias Krause [Sun, 30 Dec 2018 12:36:00 +0000 (13:36 +0100)]
kallsyms: lower alignment on ARM
As mentioned in the info pages of gas, the '.align' pseudo op's
interpretation of the alignment value is architecture specific.
It might either be a byte value or taken to the power of two.
On ARM it's actually the latter which leads to unnecessary large
alignments of 16 bytes for 32 bit builds or 256 bytes for 64 bit
builds.
Fix this by switching to '.balign' instead which is consistent
across all architectures.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Julia Lawall [Sat, 29 Dec 2018 06:14:16 +0000 (07:14 +0100)]
scripts: coccinelle: boolinit: drop warnings on named constants
Coccinelle doesn't always have access to the values of named
(#define) constants, and they may likely often be bound to true
and false values anyway, resulting in false positives. So stop
warning about them.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Julia Lawall [Fri, 28 Dec 2018 14:49:01 +0000 (15:49 +0100)]
scripts: coccinelle: check for redeclaration
Avoid reporting on the use of an iterator index variable when
the variable is redeclared.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 21 Dec 2018 06:23:02 +0000 (15:23 +0900)]
kconfig: remove unused "file" field of yylval union
This has never been used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Sun, 16 Dec 2018 14:14:11 +0000 (23:14 +0900)]
nds32: remove redundant kernel-space generic-y
This commit removes redundant generic-y defines in
arch/nds32/include/asm/Kbuild.
[1] It is redundant to define the same generic-y in both
arch/$(ARCH)/include/asm/Kbuild and
arch/$(ARCH)/include/uapi/asm/Kbuild.
Remove the following generic-y:
bitsperlong.h
bpf_perf_event.h
errno.h
fcntl.h
ioctl.h
ioctls.h
mman.h
shmbuf.h
stat.h
[2] It is redundant to define generic-y when arch-specific
implementation exists in arch/$(ARCH)/include/asm/*.h
Remove the following generic-y:
ftrace.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 26 Nov 2018 07:42:10 +0000 (16:42 +0900)]
nios2: remove unneeded HAS_DMA define
kernel/dma/Kconfig globally defines HAS_DMA as follows:
config HAS_DMA
bool
depends on !NO_DMA
default y
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Linus Torvalds [Sun, 6 Jan 2019 00:07:28 +0000 (16:07 -0800)]
Merge branch 'next' of git://git./linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Add locking for cooling device sysfs attribute in case the cooling
device state is changed by userspace and thermal framework
simultaneously. (Thara Gopinath)
- Fix a problem that passive cooling is reset improperly after system
suspend/resume. (Wei Wang)
- Cleanup the driver/thermal/ directory by moving intel and qcom
platform specific drivers to platform specific sub-directories. (Amit
Kucheria)
- Some trivial cleanups. (Lukasz Luba, Wolfram Sang)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/intel: fixup for Kconfig string parsing tightening up
drivers: thermal: Move QCOM_SPMI_TEMP_ALARM into the qcom subdir
drivers: thermal: Move various drivers for intel platforms into a subdir
thermal: Fix locking in cooling device sysfs update cur_state
Thermal: do not clear passive state during system sleep
thermal: zx2967_thermal: simplify getting .driver_data
thermal: st: st_thermal: simplify getting .driver_data
thermal: spear_thermal: simplify getting .driver_data
thermal: rockchip_thermal: simplify getting .driver_data
thermal: int340x_thermal: int3400_thermal: simplify getting .driver_data
thermal: remove unused function parameter
Linus Torvalds [Sun, 6 Jan 2019 00:01:16 +0000 (16:01 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC updates from Eduardo Valentin:
- Tegra DT binding documentation for Tegra194
- Armada now supports ap806 and cp110
- RCAR thermal now supports R8A774C0 and R8A77990
- Fixes on thermal_hwmon, IMX, generic-ADC, ST, RCAR, Broadcom,
Uniphier, QCOM, Tegra, PowerClamp, and Armada thermal drivers.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (22 commits)
thermal: generic-adc: Fix adc to temp interpolation
thermal: rcar_thermal: add R8A77990 support
dt-bindings: thermal: rcar-thermal: add R8A77990 support
thermal: rcar_thermal: add R8A774C0 support
dt-bindings: thermal: rcar-thermal: add R8A774C0 support
dt-bindings: cp110: document the thermal interrupt capabilities
dt-bindings: ap806: document the thermal interrupt capabilities
MAINTAINERS: thermal: add entry for Marvell MVEBU thermal driver
thermal: armada: add overheat interrupt support
thermal: st: fix Makefile typo
thermal: uniphier: Convert to SPDX identifier
thermal/intel_powerclamp: Change to use DEFINE_SHOW_ATTRIBUTE macro
thermal: tegra: soctherm: Change to use DEFINE_SHOW_ATTRIBUTE macro
dt-bindings: thermal: tegra-bpmp: Add Tegra194 support
thermal: imx: save one condition block for normal case of nvmem initialization
thermal: imx: fix for dependency on cpu-freq
thermal: tsens: qcom: do not create duplicate regmap debugfs entries
thermal: armada: Use PTR_ERR_OR_ZERO in armada_thermal_probe_legacy()
dt-bindings: thermal: rcar-gen3-thermal: All variants use 3 interrupts
thermal: broadcom: use devm_thermal_zone_of_sensor_register
...
Linus Torvalds [Sat, 5 Jan 2019 22:08:00 +0000 (14:08 -0800)]
Merge tag 'trace-v4.21-1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull ftrace sh build fix from Steven Rostedt:
"It appears that the zero-day bot did find a bug in my sh build.
And that I didn't have the bad code in my config file when I cross
compiled it, although there are a few other errors in sh that makes it
not build for me, I missed that I added one more"
* tag 'trace-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
sh: ftrace: Fix missing parenthesis in WARN_ON()
Linus Torvalds [Sat, 5 Jan 2019 22:05:06 +0000 (14:05 -0800)]
Merge tag '4.21-smb3-small-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb3 fixes from Steve French:
"Three fixes, one for stable, one adds the (most secure) SMB3.1.1
dialect to default list requested"
* tag '4.21-smb3-small-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: add smb3.1.1 to default dialect list
cifs: fix confusing warning message on reconnect
smb3: fix large reads on encrypted connections
Linus Torvalds [Sat, 5 Jan 2019 22:02:22 +0000 (14:02 -0800)]
Merge tag 'iomap-4.21-merge-3' of git://git./fs/xfs/xfs-linux
Pull iomap maintainer update from Darrick Wong:
"Christoph Hellwig and I have decided to take responsibility for the fs
iomap code rather than let it languish further"
* tag 'iomap-4.21-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: take responsibility for the filesystem iomap code
Linus Torvalds [Sat, 5 Jan 2019 22:00:56 +0000 (14:00 -0800)]
Merge tag 'xfs-4.21-merge-3' of git://git./fs/xfs/xfs-linux
Pull xfs fixlets from Darrick Wong:
"Remove a couple of unnecessary local variables"
* tag 'xfs-4.21-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: xfs_fsops: drop useless LIST_HEAD
xfs: xfs_buf: drop useless LIST_HEAD
Linus Torvalds [Sat, 5 Jan 2019 21:58:08 +0000 (13:58 -0800)]
Merge tag 'ceph-for-4.21-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A fairly quiet round: a couple of messenger performance improvements
from myself and a few cap handling fixes from Zheng"
* tag 'ceph-for-4.21-rc1' of git://github.com/ceph/ceph-client:
ceph: don't encode inode pathes into reconnect message
ceph: update wanted caps after resuming stale session
ceph: skip updating 'wanted' caps if caps are already issued
ceph: don't request excl caps when mount is readonly
ceph: don't update importing cap's mseq when handing cap export
libceph: switch more to bool in ceph_tcp_sendmsg()
libceph: use MSG_SENDPAGE_NOTLAST with ceph_tcp_sendpage()
libceph: use sock_no_sendpage() as a fallback in ceph_tcp_sendpage()
libceph: drop last_piece logic from write_partial_message_data()
ceph: remove redundant assignment
ceph: cleanup splice_dentry()
Olof Johansson [Sat, 5 Jan 2019 21:21:18 +0000 (13:21 -0800)]
lib/genalloc.c: include vmalloc.h
Fixes build break on most ARM/ARM64 defconfigs:
lib/genalloc.c: In function 'gen_pool_add_virt':
lib/genalloc.c:190:10: error: implicit declaration of function 'vzalloc_node'; did you mean 'kzalloc_node'?
lib/genalloc.c:190:8: warning: assignment to 'struct gen_pool_chunk *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
lib/genalloc.c: In function 'gen_pool_destroy':
lib/genalloc.c:254:3: error: implicit declaration of function 'vfree'; did you mean 'kfree'?
Fixes:
6862d2fc8185 ('lib/genalloc.c: use vzalloc_node() to allocate the bitmap')
Cc: Huang Shijie <sjhuang@iluvatar.ai>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Skidanov <alexey.skidanov@intel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 5 Jan 2019 21:25:58 +0000 (13:25 -0800)]
Merge branch 'mount.part1' of git://git./linux/kernel/git/viro/vfs
Pull vfs mount API prep from Al Viro:
"Mount API prereqs.
Mostly that's LSM mount options cleanups. There are several minor
fixes in there, but nothing earth-shattering (leaks on failure exits,
mostly)"
* 'mount.part1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (27 commits)
mount_fs: suppress MAC on MS_SUBMOUNT as well as MS_KERNMOUNT
smack: rewrite smack_sb_eat_lsm_opts()
smack: get rid of match_token()
smack: take the guts of smack_parse_opts_str() into a new helper
LSM: new method: ->sb_add_mnt_opt()
selinux: rewrite selinux_sb_eat_lsm_opts()
selinux: regularize Opt_... names a bit
selinux: switch away from match_token()
selinux: new helper - selinux_add_opt()
LSM: bury struct security_mnt_opts
smack: switch to private smack_mnt_opts
selinux: switch to private struct selinux_mnt_opts
LSM: hide struct security_mnt_opts from any generic code
selinux: kill selinux_sb_get_mnt_opts()
LSM: turn sb_eat_lsm_opts() into a method
nfs_remount(): don't leak, don't ignore LSM options quietly
btrfs: sanitize security_mnt_opts use
selinux; don't open-code a loop in sb_finish_set_opts()
LSM: split ->sb_set_mnt_opts() out of ->sb_kern_mount()
new helper: security_sb_eat_lsm_opts()
...
Linus Torvalds [Sat, 5 Jan 2019 21:18:59 +0000 (13:18 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull trivial vfs updates from Al Viro:
"A few cleanups + Neil's namespace_unlock() optimization"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
exec: make prepare_bprm_creds static
genheaders: %-<width>s had been there since v6; %-*s - since v7
VFS: use synchronize_rcu_expedited() in namespace_unlock()
iov_iter: reduce code duplication
Linus Torvalds [Sat, 5 Jan 2019 20:48:25 +0000 (12:48 -0800)]
Merge tag 'mips_fixes_4.21_1' of git://git./linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few early MIPS fixes for 4.21:
- The Broadcom BCM63xx platform sees a fix for resetting the BCM6368
ethernet switch, and the removal of a platform device we've never
had a driver for.
- The Alchemy platform sees a few fixes for bitrot that occurred
within the past few cycles.
- We now enable vectored interrupt support for the MediaTek MT7620
SoC, which makes sense since they're supported by the SoC but in
this case also works around a bug relating to the location of
exception vectors when using a recent version of U-Boot.
- The atomic64_fetch_*_relaxed() family of functions see a fix for a
regression in MIPS64 kernels since v4.19.
- Cavium Octeon III CN7xxx systems will now disable their RGMII
interfaces rather than attempt to enable them & warn about the lack
of support for doing so, as they did since initial CN7xxx ethernet
support was added in v4.7.
- The Microsemi/Microchip MSCC SoCs gain a MAINTAINERS entry.
- .mailmap now provides consistency for Dengcheng Zhu's name &
current email address"
* tag 'mips_fixes_4.21_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: OCTEON: mark RGMII interface disabled on OCTEON III
MIPS: Fix a R10000_LLSC_WAR logic in atomic.h
MIPS: BCM63XX: drop unused and broken DSP platform device
mailmap: Update name spelling and email for Dengcheng Zhu
MIPS: ralink: Select CONFIG_CPU_MIPSR2_IRQ_VI on MT7620/8
MAINTAINERS: Add a maintainer for MSCC MIPS SoCs
MIPS: Alchemy: update dma masks for devboard devices
MIPS: Alchemy: update cpu-feature-overrides
MIPS: Alchemy: drop DB1000 IrDA support bits
MIPS: alchemy: cpu_all_mask is forbidden for clock event devices
MIPS: BCM63XX: fix switch core reset on BCM6368
Linus Torvalds [Sat, 5 Jan 2019 19:48:44 +0000 (11:48 -0800)]
Merge tag 'powerpc-4.21-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A fix for the recent access_ok() change, which broke the build. We
recently added a use of type in order to squash a warning elsewhere
about type being unused.
A handful of other minor build fixes, and one defconfig update.
Thanks to: Christian Lamparter, Christophe Leroy, Diana Craciun,
Mathieu Malaterre"
* tag 'powerpc-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Drop use of 'type' from access_ok()
KVM: PPC: Book3S HV: radix: Fix uninitialized var build error
powerpc/configs: Add PPC4xx_OCM to ppc40x_defconfig
powerpc/4xx/ocm: Fix phys_addr_t printf warnings
powerpc/4xx/ocm: Fix compilation error due to PAGE_KERNEL usage
powerpc/fsl: Fixed warning: orphan section `__btb_flush_fixup'