OSDN Git Service
Florian Westphal [Mon, 31 Oct 2022 12:34:07 +0000 (13:34 +0100)]
netlink: introduce bigendian integer types
Jakub reported that the addition of the "network_byte_order"
member in struct nla_policy increases size of 32bit platforms.
Instead of scraping the bit from elsewhere Johannes suggested
to add explicit NLA_BE types instead, so do this here.
NLA_POLICY_MAX_BE() macro is removed again, there is no need
for it: NLA_POLICY_MAX(NLA_BE.., ..) will do the right thing.
NLA_BE64 can be added later.
Fixes:
08724ef69907 ("netlink: introduce NLA_POLICY_MAX_BE")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20221031123407.9158-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Mon, 31 Oct 2022 13:34:21 +0000 (14:34 +0100)]
net: lan966x: Fix unmapping of received frames using FDMA
When lan966x was receiving a frame, then it was building the skb and
after that it was calling dma_unmap_single with frame size as the
length. This actually has 2 issues:
1. It is using a length to map and a different length to unmap.
2. When the unmap was happening, the data was sync for cpu but it could
be that this will overwrite what build_skb was initializing.
The fix for these two problems is to change the order of operations.
First to sync the frame for cpu, then to build the skb and in the end to
unmap using the correct size but without sync the frame again for cpu.
Fixes:
c8349639324a ("net: lan966x: Add FDMA functionality")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221031133421.1283196-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 2 Nov 2022 04:18:20 +0000 (21:18 -0700)]
Merge branch 'net-lan966x-fixes-for-when-mtu-is-changed'
Horatiu Vultur says:
====================
net: lan966x: Fixes for when MTU is changed
There were multiple problems in different parts of the driver when
the MTU was changed.
The first problem was that the HW was missing to configure the correct
value, it was missing ETH_HLEN and ETH_FCS_LEN. The second problem was
when vlan filtering was enabled/disabled, the MRU was not adjusted
corretly. While the last issue was that the FDMA was calculated wrongly
the correct maximum MTU.
====================
Link: https://lore.kernel.org/r/20221030213636.1031408-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Sun, 30 Oct 2022 21:36:36 +0000 (22:36 +0100)]
net: lan966x: Fix FDMA when MTU is changed
When MTU is changed, FDMA is required to calculate what is the maximum
size of the frame that it can received. So it can calculate what is the
page order needed to allocate for the received frames.
The first problem was that, when the max MTU was calculated it was
reading the value from dev and not from HW, so in this way it was
missing L2 header + the FCS.
The other problem was that once the skb is created using
__build_skb_around, it would reserve some space for skb_shared_info.
So if we received a frame which size is at the limit of the page order
then the creating will failed because it would not have space to put all
the data.
Fixes:
2ea1cbac267e ("net: lan966x: Update FDMA to change MTU.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Sun, 30 Oct 2022 21:36:35 +0000 (22:36 +0100)]
net: lan966x: Adjust maximum frame size when vlan is enabled/disabled
When vlan filtering is enabled/disabled, it is required to adjust the
maximum received frame size that it can received. When vlan filtering is
enabled, it would all to receive extra 4 bytes, that are the vlan tag.
So the maximum frame size would be 1522 with a vlan tag. If vlan
filtering is disabled then the maximum frame size would be 1518
regardless if there is or not a vlan tag.
Fixes:
6d2c186afa5d ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Sun, 30 Oct 2022 21:36:34 +0000 (22:36 +0100)]
net: lan966x: Fix the MTU calculation
When the MTU was changed, the lan966x didn't take in consideration
the L2 header and the FCS. So the HW was configured with a smaller
value than what was desired. Therefore the correct value to configure
the HW would be new_mtu + ETH_HLEN + ETH_FCS_LEN.
The vlan tag is not considered here, because at the time when the
blamed commit was added, there was no vlan filtering support. The
vlan fix will be part of the next patch.
Fixes:
d28d6d2e37d1 ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christophe JAILLET [Sat, 29 Oct 2022 20:57:11 +0000 (22:57 +0200)]
sfc: Fix an error handling path in efx_pci_probe()
If an error occurs after the first kzalloc() the corresponding memory
allocation is never freed.
Add the missing kfree() in the error handling path, as already done in the
remove() function.
Fixes:
7e773594dada ("sfc: Separate efx_nic memory from net_device memory")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/dc114193121c52c8fa3779e49bdd99d4b41344a9.1667077009.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Sat, 29 Oct 2022 09:41:01 +0000 (17:41 +0800)]
net: tun: fix bugs for oversize packet when napi frags enabled
Recently, we got two syzkaller problems because of oversize packet
when napi frags enabled.
One of the problems is because the first seg size of the iov_iter
from user space is very big, it is
2147479538 which is bigger than
the threshold value for bail out early in __alloc_pages(). And
skb->pfmemalloc is true, __kmalloc_reserve() would use pfmemalloc
reserves without __GFP_NOWARN flag. Thus we got a warning as following:
========================================================
WARNING: CPU: 1 PID: 17965 at mm/page_alloc.c:5295 __alloc_pages+0x1308/0x16c4 mm/page_alloc.c:5295
...
Call trace:
__alloc_pages+0x1308/0x16c4 mm/page_alloc.c:5295
__alloc_pages_node include/linux/gfp.h:550 [inline]
alloc_pages_node include/linux/gfp.h:564 [inline]
kmalloc_large_node+0x94/0x350 mm/slub.c:4038
__kmalloc_node_track_caller+0x620/0x8e4 mm/slub.c:4545
__kmalloc_reserve.constprop.0+0x1e4/0x2b0 net/core/skbuff.c:151
pskb_expand_head+0x130/0x8b0 net/core/skbuff.c:1654
__skb_grow include/linux/skbuff.h:2779 [inline]
tun_napi_alloc_frags+0x144/0x610 drivers/net/tun.c:1477
tun_get_user+0x31c/0x2010 drivers/net/tun.c:1835
tun_chr_write_iter+0x98/0x100 drivers/net/tun.c:2036
The other problem is because odd IPv6 packets without NEXTHDR_NONE
extension header and have big packet length, it is
2127925 which is
bigger than ETH_MAX_MTU(65535). After ipv6_gso_pull_exthdrs() in
ipv6_gro_receive(), network_header offset and transport_header offset
are all bigger than U16_MAX. That would trigger skb->network_header
and skb->transport_header overflow error, because they are all '__u16'
type. Eventually, it would affect the value for __skb_push(skb, value),
and make it be a big value. After __skb_push() in ipv6_gro_receive(),
skb->data would less than skb->head, an out of bounds memory bug occurred.
That would trigger the problem as following:
==================================================================
BUG: KASAN: use-after-free in eth_type_trans+0x100/0x260
...
Call trace:
dump_backtrace+0xd8/0x130
show_stack+0x1c/0x50
dump_stack_lvl+0x64/0x7c
print_address_description.constprop.0+0xbc/0x2e8
print_report+0x100/0x1e4
kasan_report+0x80/0x120
__asan_load8+0x78/0xa0
eth_type_trans+0x100/0x260
napi_gro_frags+0x164/0x550
tun_get_user+0xda4/0x1270
tun_chr_write_iter+0x74/0x130
do_iter_readv_writev+0x130/0x1ec
do_iter_write+0xbc/0x1e0
vfs_writev+0x13c/0x26c
To fix the problems, restrict the packet size less than
(ETH_MAX_MTU - NET_SKB_PAD - NET_IP_ALIGN) which has considered reserved
skb space in napi_alloc_skb() because transport_header is an offset from
skb->head. Add len check in tun_napi_alloc_frags() simply.
Fixes:
90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221029094101.1653855-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rick Lindsley [Fri, 28 Oct 2022 20:35:11 +0000 (13:35 -0700)]
ibmvnic: change maintainers for vnic driver
Changed maintainers for vnic driver, since Dany has new responsibilities.
Also added Nick Child as reviewer.
Signed-off-by: Rick Lindsley <ricklind@us.ibm.com>
Link: https://lore.kernel.org/r/20221028203509.4070154-1-ricklind@us.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Fri, 28 Oct 2022 15:05:00 +0000 (18:05 +0300)]
net: sched: Fix use after free in red_enqueue()
We can't use "skb" again after passing it to qdisc_enqueue(). This is
basically identical to commit
2f09707d0c97 ("sch_sfb: Also store skb
len before calling child enqueue").
Fixes:
d7f4f332f082 ("sch_red: update backlog as well")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Changzhong [Fri, 28 Oct 2022 02:09:11 +0000 (10:09 +0800)]
net: fec: fix improper use of NETDEV_TX_BUSY
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fix it by returning NETDEV_TX_OK in case of dma_map_single() fails.
Fixes:
79f339125ea3 ("net: fec: Add software TSO support")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 30 Oct 2022 21:43:26 +0000 (21:43 +0000)]
Merge branch 'nfc-skb-leaks'
Shang XiaoJing says:
====================
nfc: Fix potential memory leak of skb
There are 6 kinds of send functions can be called by nci_send_frame():
virtual_nci_send(),
fdp_nci_send(),
nxp_nci_send(),
s3fwrn5_nci_send(),
nfcmrvl_nci_send(),
st_nci_send();
1. virtual_nci_send() will memleak the skb, and has been fixed before.
2. fdp_nci_send() won't free the skb no matter whether write() succeed.
3-4. nxp_nci_send() and s3fwrn5_nci_send() will only free the skb when
write() failed, however write() will not free the skb by itself for when
succeeds.
5. nfcmrvl_nci_send() will call nfcmrvl_XXX_nci_send(), where some of
them will free the skb, but nfcmrvl_i2c_nci_send() only free the skb
when i2c_master_send() return >=0, and memleak will happen when
i2c_master_send() failed in nfcmrvl_i2c_nci_send().
6. st_nci_send() will queue the skb into other list and finally be
freed.
Fix the potential memory leak of skb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:32 +0000 (22:03 +0800)]
nfc: nfcmrvl: Fix potential memory leak in nfcmrvl_i2c_nci_send()
nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb
should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send()
will only free skb when i2c_master_send() return >=0, which means skb
will memleak when i2c_master_send() failed. Free skb no matter whether
i2c_master_send() succeeds.
Fixes:
b5b3e23e4cac ("NFC: nfcmrvl: add i2c driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:31 +0000 (22:03 +0800)]
nfc: s3fwrn5: Fix potential memory leak in s3fwrn5_nci_send()
s3fwrn5_nci_send() will call s3fwrn5_i2c_write() or s3fwrn82_uart_write(),
and free the skb if write() failed. However, even if the write() run
succeeds, the skb will not be freed in write(). As the result, the skb
will memleak. s3fwrn5_nci_send() should also free the skb when write()
succeeds.
Fixes:
c04c674fadeb ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:30 +0000 (22:03 +0800)]
nfc: nxp-nci: Fix potential memory leak in nxp_nci_send()
nxp_nci_send() will call nxp_nci_i2c_write(), and only free skb when
nxp_nci_i2c_write() failed. However, even if the nxp_nci_i2c_write()
run succeeds, the skb will not be freed in nxp_nci_i2c_write(). As the
result, the skb will memleak. nxp_nci_send() should also free the skb
when nxp_nci_i2c_write() succeeds.
Fixes:
dece45855a8b ("NFC: nxp-nci: Add support for NXP NCI chips")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:29 +0000 (22:03 +0800)]
nfc: fdp: Fix potential memory leak in fdp_nci_send()
fdp_nci_send() will call fdp_nci_i2c_write that will not free skb in
the function. As a result, when fdp_nci_i2c_write() finished, the skb
will memleak. fdp_nci_send() should free skb after fdp_nci_i2c_write()
finished.
Fixes:
a06347c04c13 ("NFC: Add Intel Fields Peak NFC solution driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 27 Oct 2022 14:54:39 +0000 (17:54 +0300)]
net: dsa: fall back to default tagger if we can't load the one from DT
DSA tagging protocol drivers can be changed at runtime through sysfs and
at probe time through the device tree (support for the latter was added
later).
When changing through sysfs, it is assumed that the module for the new
tagging protocol was already loaded into the kernel (in fact this is
only a concern for Ocelot/Felix switches, where we have tag_ocelot.ko
and tag_ocelot_8021q.ko; for every other switch, the default and
alternative protocols are compiled within the same .ko, so there is
nothing for the user to load).
The kernel cannot currently call request_module(), because it has no way
of constructing the modalias name of the tagging protocol driver
("dsa_tag-%d", where the number is one of DSA_TAG_PROTO_*_VALUE).
The device tree only contains the string name of the tagging protocol
("ocelot-8021q"), and the only mapping between the string and the
DSA_TAG_PROTO_OCELOT_8021Q_VALUE is present in tag_ocelot_8021q.ko.
So this is a chicken-and-egg situation and dsa_core.ko has nothing based
on which it can automatically request the insertion of the module.
As a consequence, if CONFIG_NET_DSA_TAG_OCELOT_8021Q is built as module,
the switch will forever defer probing.
The long-term solution is to make DSA call request_module() somehow,
but that probably needs some refactoring.
What we can do to keep operating with existing device tree blobs is to
cancel the attempt to change the tagging protocol with the one specified
there, and to remain operating with the default one. Depending on the
situation, the default protocol might still allow some functionality
(in the case of ocelot, it does), and it's better to have that than to
fail to probe.
Fixes:
deff710703d8 ("net: dsa: Allow default tag protocol to be overridden from DT")
Link: https://lore.kernel.org/lkml/20221027113248.420216-1-michael@walle.cc/
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027145439.3086017-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandru Tachici [Thu, 27 Oct 2022 09:56:55 +0000 (12:56 +0300)]
net: ethernet: adi: adin1110: Fix notifiers
ADIN1110 was registering netdev_notifiers on each device probe.
This leads to warnings/probe failures because of double registration
of the same notifier when to adin1110/2111 devices are connected to
the same system.
Move the registration of netdev_notifiers in module init call,
in this way multiple driver instances can use the same notifiers.
Fixes:
bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20221027095655.89890-2-alexandru.tachici@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 29 Oct 2022 03:21:29 +0000 (20:21 -0700)]
Merge branch 'a-few-corrections-for-sock_support_zc'
Pavel Begunkov says:
====================
a few corrections for SOCK_SUPPORT_ZC
There are several places/cases that got overlooked in regards to
SOCK_SUPPORT_ZC. We're lacking the flag for IPv6 UDP sockets and
accepted TCP sockets. We also should clear the flag when someone
tries to hijack a socket by replacing the ->sk_prot callbacks.
====================
Link: https://lore.kernel.org/r/cover.1666825799.git.asml.silence@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Metzmacher [Wed, 26 Oct 2022 23:25:59 +0000 (00:25 +0100)]
net: also flag accepted sockets supporting msghdr originated zerocopy
Without this only the client initiated tcp sockets have SOCK_SUPPORT_ZC.
The listening socket on the server also has it, but the accepted
connections didn't, which meant IORING_OP_SEND[MSG]_ZC will always
fails with -EOPNOTSUPP.
Fixes:
e993ffe3da4b ("net: flag sockets supporting msghdr originated zerocopy")
Cc: <stable@vger.kernel.org> # 6.0
CC: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/io-uring/20221024141503.22b4e251@kernel.org/T/#m38aa19b0b825758fb97860a38ad13122051f9dda
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Begunkov [Wed, 26 Oct 2022 23:25:58 +0000 (00:25 +0100)]
net/ulp: remove SOCK_SUPPORT_ZC from tls sockets
Remove SOCK_SUPPORT_ZC when we're setting ulp as it might not support
msghdr::ubuf_info, e.g. like TLS replacing ->sk_prot with a new set of
handlers.
Cc: <stable@vger.kernel.org> # 6.0
Reported-by: Jakub Kicinski <kuba@kernel.org>
Fixes:
e993ffe3da4bc ("net: flag sockets supporting msghdr originated zerocopy")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Begunkov [Wed, 26 Oct 2022 23:25:57 +0000 (00:25 +0100)]
net: remove SOCK_SUPPORT_ZC from sockmap
sockmap replaces ->sk_prot with its own callbacks, we should remove
SOCK_SUPPORT_ZC as the new proto doesn't support msghdr::ubuf_info.
Cc: <stable@vger.kernel.org> # 6.0
Reported-by: Jakub Kicinski <kuba@kernel.org>
Fixes:
e993ffe3da4bc ("net: flag sockets supporting msghdr originated zerocopy")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Begunkov [Wed, 26 Oct 2022 23:25:56 +0000 (00:25 +0100)]
udp: advertise ipv6 udp support for msghdr::ubuf_info
Mark udp ipv6 as supporting msghdr::ubuf_info. In the original commit
SOCK_SUPPORT_ZC was supposed to be set by a udp_init_sock() call from
udp6_init_sock(), but
d38afeec26ed4 ("tcp/udp: Call inet6_destroy_sock() in IPv6 ...")
removed it and so ipv6 udp misses the flag.
Cc: <stable@vger.kernel.org> # 6.0
Fixes:
e993ffe3da4bc ("net: flag sockets supporting msghdr originated zerocopy")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Govindarajulu Varadarajan [Fri, 28 Oct 2022 04:21:59 +0000 (21:21 -0700)]
enic: MAINTAINERS: Update enic maintainers
Update enic maintainers.
Signed-off-by: Govindarajulu Varadarajan <govind.varadar@gmail.com>
Link: https://lore.kernel.org/r/20221028042159.735670-1-govind.varadar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 28 Oct 2022 03:25:01 +0000 (20:25 -0700)]
net: openvswitch: add missing .resv_start_op
I missed one of the families in OvS when annotating .resv_start_op.
This triggers the warning added in commit
ce48ebdd5651 ("genetlink:
limit the use of validation workarounds to old ops").
Reported-by: syzbot+40eb8c0447c0e47a7e9b@syzkaller.appspotmail.com
Fixes:
9c5d03d36251 ("genetlink: start to validate reserved header bytes")
Link: https://lore.kernel.org/r/20221028032501.2724270-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 27 Oct 2022 21:21:07 +0000 (14:21 -0700)]
netlink: hide validation union fields from kdoc
Mark the validation fields as private, users shouldn't set
them directly and they are too complicated to explain in
a more succinct way (there's already a long explanation
in the comment above).
The strict_start_type field is set directly and has a dedicated
comment so move that above the "private" section.
Link: https://lore.kernel.org/r/20221027212107.2639255-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Radhey Shyam Pandey [Wed, 26 Oct 2022 15:15:24 +0000 (20:45 +0530)]
net: emaclite: update reset_lock member documentation
Instead of generic description, mention what reset_lock actually
protects i.e. lock to serialize xmit and tx_timeout execution.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chen Zhongjin [Wed, 26 Oct 2022 02:03:21 +0000 (10:03 +0800)]
net: dsa: Fix possible memory leaks in dsa_loop_init()
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies
4295040478 (age 238.976s)
backtrace:
[<
000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<
00000000a9c44622>] phy_device_create+0x5d/0x970
[<
00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<
00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<
000000008a834798>] fixed_phy_register+0x84/0xb0
[<
0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes:
98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 27 Oct 2022 20:36:59 +0000 (13:36 -0700)]
Merge tag 'net-6.1-rc3-2' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from 802.15.4 (Zigbee et al).
Current release - regressions:
- ipa: fix bugs in the register conversion for IPA v3.1 and v3.5.1
Current release - new code bugs:
- mptcp: fix abba deadlock on fastopen
- eth: stmmac: rk3588: allow multiple gmac controllers in one system
Previous releases - regressions:
- ip: rework the fix for dflt addr selection for connected nexthop
- net: couple more fixes for misinterpreting bits in struct page
after the signature was added
Previous releases - always broken:
- ipv6: ensure sane device mtu in tunnels
- openvswitch: switch from WARN to pr_warn on a user-triggerable path
- ethtool: eeprom: fix null-deref on genl_info in dump
- ieee802154: more return code fixes for corner cases in
dgram_sendmsg
- mac802154: fix link-quality-indicator recording
- eth: mlx5: fixes for IPsec, PTP timestamps, OvS and conntrack
offload
- eth: fec: limit register access on i.MX6UL
- eth: bcm4908_enet: update TX stats after actual transmission
- can: rcar_canfd: improve IRQ handling for RZ/G2L
Misc:
- genetlink: piggy back on the newly added resv_op_start to enforce
more sanity checks on new commands"
* tag 'net-6.1-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
net: enetc: survive memory pressure without crashing
kcm: do not sense pfmemalloc status in kcm_sendpage()
net: do not sense pfmemalloc status in skb_append_pagefrags()
net/mlx5e: Fix macsec sci endianness at rx sa update
net/mlx5e: Fix wrong bitwise comparison usage in macsec_fs_rx_add_rule function
net/mlx5e: Fix macsec rx security association (SA) update/delete
net/mlx5e: Fix macsec coverity issue at rx sa update
net/mlx5: Fix crash during sync firmware reset
net/mlx5: Update fw fatal reporter state on PCI handlers successful recover
net/mlx5e: TC, Fix cloned flow attr instance dests are not zeroed
net/mlx5e: TC, Reject forwarding from internal port to internal port
net/mlx5: Fix possible use-after-free in async command interface
net/mlx5: ASO, Create the ASO SQ with the correct timestamp format
net/mlx5e: Update restore chain id for slow path packets
net/mlx5e: Extend SKB room check to include PTP-SQ
net/mlx5: DR, Fix matcher disconnect error flow
net/mlx5: Wait for firmware to enable CRS before pci_restore_state
net/mlx5e: Do not increment ESN when updating IPsec ESN state
netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir failed
netdevsim: fix memory leak in nsim_drv_probe() when nsim_dev_resources_register() failed
...
Linus Torvalds [Thu, 27 Oct 2022 20:16:36 +0000 (13:16 -0700)]
Merge tag 'execve-v6.1-rc3' of git://git./linux/kernel/git/kees/linux
Pull execve fixes from Kees Cook:
- Fix an ancient signal action copy race (Bernd Edlinger)
- Fix a memory leak in ELF loader, when under memory pressure (Li
Zetao)
* tag 'execve-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
fs/binfmt_elf: Fix memory leak in load_elf_binary()
exec: Copy oldsighand->action under spin-lock
Linus Torvalds [Thu, 27 Oct 2022 19:31:57 +0000 (12:31 -0700)]
Merge tag 'hardening-v6.1-rc3' of git://git./linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- Fix older Clang vs recent overflow KUnit test additions (Nick
Desaulniers, Kees Cook)
- Fix kern-doc visibility for overflow helpers (Kees Cook)
* tag 'hardening-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
overflow: Refactor test skips for Clang-specific issues
overflow: disable failing tests for older clang versions
overflow: Fix kern-doc markup for functions
Linus Torvalds [Thu, 27 Oct 2022 19:21:57 +0000 (12:21 -0700)]
Merge tag 'media/v6.1-3' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A bunch of patches addressing issues in the vivid driver and adding
new checks in V4L2 to validate the input parameters from some ioctls"
* tag 'media/v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vivid.rst: loop_video is set on the capture devnode
media: vivid: set num_in/outputs to 0 if not supported
media: vivid: drop GFP_DMA32
media: vivid: fix control handler mutex deadlock
media: videodev2.h: V4L2_DV_BT_BLANKING_HEIGHT should check 'interlaced'
media: v4l2-dv-timings: add sanity checks for blanking values
media: vivid: dev->bitmap_cap wasn't freed in all cases
media: vivid: s_fbuf: add more sanity checks
Linus Torvalds [Thu, 27 Oct 2022 18:44:18 +0000 (11:44 -0700)]
Merge tag 'fscrypt-for-linus' of git://git./fs/fscrypt/fscrypt
Pull fscrypt fix from Eric Biggers:
"Fix a memory leak that was introduced by a change that went into -rc1"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
fscrypt: fix keyring memory leak on mount failure
Vladimir Oltean [Thu, 27 Oct 2022 18:29:25 +0000 (21:29 +0300)]
net: enetc: survive memory pressure without crashing
Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes:
d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Thu, 27 Oct 2022 04:06:37 +0000 (04:06 +0000)]
kcm: do not sense pfmemalloc status in kcm_sendpage()
Similar to changes done in TCP in blamed commit.
We should not sense pfmemalloc status in sendpage() methods.
Fixes:
326140063946 ("tcp: TX zerocopy should not sense pfmemalloc status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221027040637.1107703-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Thu, 27 Oct 2022 04:03:46 +0000 (04:03 +0000)]
net: do not sense pfmemalloc status in skb_append_pagefrags()
skb_append_pagefrags() is used by af_unix and udp sendpage()
implementation so far.
In commit
326140063946 ("tcp: TX zerocopy should not sense
pfmemalloc status") we explained why we should not sense
pfmemalloc status for pages owned by user space.
We should also use skb_fill_page_desc_noacc()
in skb_append_pagefrags() to avoid following KCSAN report:
BUG: KCSAN: data-race in lru_add_fn / skb_append_pagefrags
write to 0xffffea00058fc1c8 of 8 bytes by task 17319 on cpu 0:
__list_add include/linux/list.h:73 [inline]
list_add include/linux/list.h:88 [inline]
lruvec_add_folio include/linux/mm_inline.h:323 [inline]
lru_add_fn+0x327/0x410 mm/swap.c:228
folio_batch_move_lru+0x1e1/0x2a0 mm/swap.c:246
lru_add_drain_cpu+0x73/0x250 mm/swap.c:669
lru_add_drain+0x21/0x60 mm/swap.c:773
free_pages_and_swap_cache+0x16/0x70 mm/swap_state.c:311
tlb_batch_pages_flush mm/mmu_gather.c:59 [inline]
tlb_flush_mmu_free mm/mmu_gather.c:256 [inline]
tlb_flush_mmu+0x5b2/0x640 mm/mmu_gather.c:263
tlb_finish_mmu+0x86/0x100 mm/mmu_gather.c:363
exit_mmap+0x190/0x4d0 mm/mmap.c:3098
__mmput+0x27/0x1b0 kernel/fork.c:1185
mmput+0x3d/0x50 kernel/fork.c:1207
copy_process+0x19fc/0x2100 kernel/fork.c:2518
kernel_clone+0x166/0x550 kernel/fork.c:2671
__do_sys_clone kernel/fork.c:2812 [inline]
__se_sys_clone kernel/fork.c:2796 [inline]
__x64_sys_clone+0xc3/0xf0 kernel/fork.c:2796
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffffea00058fc1c8 of 8 bytes by task 17325 on cpu 1:
page_is_pfmemalloc include/linux/mm.h:1817 [inline]
__skb_fill_page_desc include/linux/skbuff.h:2432 [inline]
skb_fill_page_desc include/linux/skbuff.h:2453 [inline]
skb_append_pagefrags+0x210/0x600 net/core/skbuff.c:3974
unix_stream_sendpage+0x45e/0x990 net/unix/af_unix.c:2338
kernel_sendpage+0x184/0x300 net/socket.c:3561
sock_sendpage+0x5a/0x70 net/socket.c:1054
pipe_to_sendpage+0x128/0x160 fs/splice.c:361
splice_from_pipe_feed fs/splice.c:415 [inline]
__splice_from_pipe+0x222/0x4d0 fs/splice.c:559
splice_from_pipe fs/splice.c:594 [inline]
generic_splice_sendpage+0x89/0xc0 fs/splice.c:743
do_splice_from fs/splice.c:764 [inline]
direct_splice_actor+0x80/0xa0 fs/splice.c:931
splice_direct_to_actor+0x305/0x620 fs/splice.c:886
do_splice_direct+0xfb/0x180 fs/splice.c:974
do_sendfile+0x3bf/0x910 fs/read_write.c:1255
__do_sys_sendfile64 fs/read_write.c:1323 [inline]
__se_sys_sendfile64 fs/read_write.c:1309 [inline]
__x64_sys_sendfile64+0x10c/0x150 fs/read_write.c:1309
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x0000000000000000 -> 0xffffea00058fc188
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 17325 Comm: syz-executor.0 Not tainted
6.1.0-rc1-syzkaller-00158-g440b7895c990-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/11/2022
Fixes:
326140063946 ("tcp: TX zerocopy should not sense pfmemalloc status")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221027040346.1104204-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raed Salem [Wed, 26 Oct 2022 13:51:53 +0000 (14:51 +0100)]
net/mlx5e: Fix macsec sci endianness at rx sa update
The cited commit at rx sa update operation passes the sci object
attribute, in the wrong endianness and not as expected by the HW
effectively create malformed hw sa context in case of update rx sa
consequently, HW produces unexpected MACsec packets which uses this
sa.
Fix by passing sci to create macsec object with the correct endianness,
while at it add __force u64 to prevent sparse check error of type
"sparse: error: incorrect type in assignment".
Fixes:
aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-16-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raed Salem [Wed, 26 Oct 2022 13:51:52 +0000 (14:51 +0100)]
net/mlx5e: Fix wrong bitwise comparison usage in macsec_fs_rx_add_rule function
The cited commit produces a sparse check error of type
"sparse: error: restricted __be64 degrades to integer". The
offending line wrongly did a bitwise operation between two different
storage types one of 64 bit when the other smaller side is 16 bit
which caused the above sparse error, furthermore bitwise operation
usage here is wrong in the first place as the constant MACSEC_PORT_ES
is not a bitwise field.
Fix by using the right mask to get the lower 16 bit if the sci number,
and use comparison operator '==' instead of bitwise '&' operator.
Fixes:
3b20949cb21b ("net/mlx5e: Add MACsec RX steering rules")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-15-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raed Salem [Wed, 26 Oct 2022 13:51:51 +0000 (14:51 +0100)]
net/mlx5e: Fix macsec rx security association (SA) update/delete
The cited commit adds the support for update/delete MACsec Rx SA,
naturally, these operations need to check if the SA in question exists
to update/delete the SA and return error code otherwise, however they
do just the opposite i.e. return with error if the SA exists
Fix by change the check to return error in case the SA in question does
not exist, adjust error message and code accordingly.
Fixes:
aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-14-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raed Salem [Wed, 26 Oct 2022 13:51:50 +0000 (14:51 +0100)]
net/mlx5e: Fix macsec coverity issue at rx sa update
The cited commit at update rx sa operation passes object attributes
to MACsec object create function without initializing/setting all
attributes fields leaving some of them with garbage values, therefore
violating the implicit assumption at create object function, which
assumes that all input object attributes fields are set.
Fix by initializing the object attributes struct to zero, thus leaving
unset fields with the legal zero value.
Fixes:
aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-13-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Suresh Devarakonda [Wed, 26 Oct 2022 13:51:49 +0000 (14:51 +0100)]
net/mlx5: Fix crash during sync firmware reset
When setting Bluefield to DPU NIC mode using mlxconfig tool + sync
firmware reset flow, we run into scenario where the host was not
eswitch manager at the time of mlx5 driver load but becomes eswitch manager
after the sync firmware reset flow. This results in null pointer
access of mpfs structure during mac filter add. This change prevents null
pointer access but mpfs table entries will not be added.
Fixes:
5ec697446f46 ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Suresh Devarakonda <ramad@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Roy Novich [Wed, 26 Oct 2022 13:51:48 +0000 (14:51 +0100)]
net/mlx5: Update fw fatal reporter state on PCI handlers successful recover
Update devlink health fw fatal reporter state to "healthy" is needed by
strictly calling devlink_health_reporter_state_update() after recovery
was done by PCI error handler. This is needed when fw_fatal reporter was
triggered due to PCI error. Poll health is called and set reporter state
to error. Health recovery failed (since EEH didn't re-enable the PCI).
PCI handlers keep on recover flow and succeed later without devlink
acknowledgment. Fix this by adding devlink state update at the end of
the PCI handler recovery process.
Fixes:
6181e5cb752e ("devlink: add support for reporter recovery completion")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Roi Dayan [Wed, 26 Oct 2022 13:51:47 +0000 (14:51 +0100)]
net/mlx5e: TC, Fix cloned flow attr instance dests are not zeroed
On multi table split the driver creates a new attr instance with
data being copied from prev attr instance zeroing action flags.
Also need to reset dests properties to avoid incorrect dests per attr.
Fixes:
8300f225268b ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-10-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ariel Levkovich [Wed, 26 Oct 2022 13:51:46 +0000 (14:51 +0100)]
net/mlx5e: TC, Reject forwarding from internal port to internal port
Reject TC rules that forward from internal port to internal port
as it is not supported.
This include rules that are explicitly have internal port as
the filter device as well as rules that apply on tunnel interfaces
as the route device for the tunnel interface can be an internal
port.
Fixes:
27484f7170ed ("net/mlx5e: Offload tc rules that redirect to ovs internal port")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-9-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan [Wed, 26 Oct 2022 13:51:45 +0000 (14:51 +0100)]
net/mlx5: Fix possible use-after-free in async command interface
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr
ffff888139cd12f4 by task swapper/5/0
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x7d
print_report.cold+0x2d5/0x684
? do_raw_spin_lock+0x23d/0x270
kasan_report+0xb1/0x1a0
? do_raw_spin_lock+0x23d/0x270
do_raw_spin_lock+0x23d/0x270
? rwlock_bug.part.0+0x90/0x90
? __delete_object+0xb8/0x100
? lock_downgrade+0x6e0/0x6e0
_raw_spin_lock_irqsave+0x43/0x60
? __wake_up_common_lock+0xb9/0x140
__wake_up_common_lock+0xb9/0x140
? __wake_up_common+0x650/0x650
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kasan_set_track+0x21/0x30
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kfree+0x1ba/0x520
? do_raw_spin_unlock+0x54/0x220
mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core]
? dump_command+0xcc0/0xcc0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
? irq_release+0x140/0x140 [mlx5_core]
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x1f2/0x620
handle_irq_event+0xb2/0x1d0
handle_edge_irq+0x21e/0xb00
__common_interrupt+0x79/0x1a0
common_interrupt+0x78/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x42/0x60
Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 <c3> 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00
RSP: 0018:
ffff888100dbfdf0 EFLAGS:
00000242
RAX:
0000000000000001 RBX:
ffffffff84ecbd48 RCX:
1ffffffff0afe110
RDX:
0000000000000004 RSI:
0000000000000000 RDI:
ffffffff835cc9bc
RBP:
0000000000000005 R08:
0000000000000001 R09:
ffff88881dec4ac3
R10:
ffffed1103bd8958 R11:
0000017d0ca571c9 R12:
0000000000000005
R13:
ffffffff84f024e0 R14:
0000000000000000 R15:
dffffc0000000000
? default_idle_call+0xcc/0x450
default_idle_call+0xec/0x450
do_idle+0x394/0x450
? arch_cpu_idle_exit+0x40/0x40
? do_idle+0x17/0x450
cpu_startup_entry+0x19/0x20
start_secondary+0x221/0x2b0
? set_cpu_sibling_map+0x2070/0x2070
secondary_startup_64_no_verify+0xcd/0xdb
</TASK>
Allocated by task 49502:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
kvmalloc_node+0x48/0xe0
mlx5e_bulk_async_init+0x35/0x110 [mlx5_core]
mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 49502:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
____kasan_slab_free+0x11d/0x1b0
kfree+0x1ba/0x520
mlx5e_tls_priv_tx_list_cleanup+0x2e7/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes:
e355477ed9e4 ("net/mlx5: Make mlx5_cmd_exec_cb() a safe API")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed [Wed, 26 Oct 2022 13:51:44 +0000 (14:51 +0100)]
net/mlx5: ASO, Create the ASO SQ with the correct timestamp format
mlx5 SQs must select the timestamp format explicitly according to the
active clock mode, select the current active timestamp mode so ASO SQ create
will succeed.
This fixes the following error prints when trying to create ipsec ASO SQ
while the timestamp format is real time mode.
mlx5_cmd_out_err:778:(pid 34874): CREATE_SQ(0x904) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xd61c0b), err(-22)
mlx5_aso_create_sq:285:(pid 34874): Failed to open aso wq sq, err=-22
mlx5e_ipsec_init:436:(pid 34874): IPSec initialization failed, -22
Fixes:
cdd04f4d4d71 ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-7-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Blakey [Wed, 26 Oct 2022 13:51:43 +0000 (14:51 +0100)]
net/mlx5e: Update restore chain id for slow path packets
Currently encap slow path rules just forward to software without
setting the chain id miss register, so driver doesn't restore
the chain, and packets hitting this rule will restart from tc chain
0 instead of continuing to the chain the encap rule was on.
Fix this by setting the chain id miss register to the chain id mapping.
Fixes:
8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-6-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aya Levin [Wed, 26 Oct 2022 13:51:42 +0000 (14:51 +0100)]
net/mlx5e: Extend SKB room check to include PTP-SQ
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes:
1880bc4e4a96 ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rongwei Liu [Wed, 26 Oct 2022 13:51:41 +0000 (14:51 +0100)]
net/mlx5: DR, Fix matcher disconnect error flow
When 2nd flow rules arrives, it will merge together with the
1st one if matcher criteria is the same.
If merge fails, driver will rollback the merge contents, and
reject the 2nd rule. At rollback stage, matcher can't be
disconnected unconditionally, otherise the 1st rule can't be
hit anymore.
Add logic to check if the matcher should be disconnected or not.
Fixes:
cc2295cd54e4 ("net/mlx5: DR, Improve steering for empty or RX/TX-only matchers")
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Moshe Shemesh [Wed, 26 Oct 2022 13:51:40 +0000 (14:51 +0100)]
net/mlx5: Wait for firmware to enable CRS before pci_restore_state
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Fixes:
eabe8e5e88f5 ("net/mlx5: Handle sync reset now event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hyong Youb Kim [Wed, 26 Oct 2022 13:51:39 +0000 (14:51 +0100)]
net/mlx5e: Do not increment ESN when updating IPsec ESN state
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes:
cb01008390bb ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 27 Oct 2022 17:47:31 +0000 (10:47 -0700)]
Merge branch 'fix-some-issues-in-netdevsim-driver'
Zhengchao Shao says:
====================
fix some issues in netdevsim driver
When strace tool is used to perform memory injection, memory leaks and
files not removed issues are found. Fix them.
====================
Link: https://lore.kernel.org/r/20221026014642.116261-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Wed, 26 Oct 2022 01:46:42 +0000 (09:46 +0800)]
netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir failed
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed.
Otherwise, the netdevsim device will not be created next time. Kernel
reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim'
already present!
Fixes:
ab1d0cc004d7 ("netdevsim: change debugfs tree topology")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Wed, 26 Oct 2022 01:46:41 +0000 (09:46 +0800)]
netdevsim: fix memory leak in nsim_drv_probe() when nsim_dev_resources_register() failed
If some items in nsim_dev_resources_register() fail, memory leak will
occur. The following is the memory leak information.
unreferenced object 0xffff888074c02600 (size 128):
comm "echo", pid 8159, jiffies
4294945184 (age 493.530s)
hex dump (first 32 bytes):
40 47 ea 89 ff ff ff ff 01 00 00 00 00 00 00 00 @G..............
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
backtrace:
[<
0000000011a31c98>] kmalloc_trace+0x22/0x60
[<
0000000027384c69>] devl_resource_register+0x144/0x4e0
[<
00000000a16db248>] nsim_drv_probe+0x37a/0x1260
[<
000000007d1f448c>] really_probe+0x20b/0xb10
[<
00000000c416848a>] __driver_probe_device+0x1b3/0x4a0
[<
00000000077e0351>] driver_probe_device+0x49/0x140
[<
0000000054f2465a>] __device_attach_driver+0x18c/0x2a0
[<
000000008538f359>] bus_for_each_drv+0x151/0x1d0
[<
0000000038e09747>] __device_attach+0x1c9/0x4e0
[<
00000000dd86e533>] bus_probe_device+0x1d5/0x280
[<
00000000839bea35>] device_add+0xae0/0x1cb0
[<
000000009c2abf46>] new_device_store+0x3b6/0x5f0
[<
00000000fb823d7f>] bus_attr_store+0x72/0xa0
[<
000000007acc4295>] sysfs_kf_write+0x106/0x160
[<
000000005f50cb4d>] kernfs_fop_write_iter+0x3a8/0x5a0
[<
0000000075eb41bf>] vfs_write+0x8f0/0xc80
Fixes:
37923ed6b8ce ("netdevsim: Add simple FIB resource controller via devlink")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Wed, 26 Oct 2022 01:54:05 +0000 (09:54 +0800)]
netdevsim: fix memory leak in nsim_bus_dev_new()
If device_register() failed in nsim_bus_dev_new(), the value of reference
in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be
released.
unreferenced object 0xffff88810352c480 (size 16):
comm "echo", pid 5691, jiffies
4294945921 (age 133.270s)
hex dump (first 16 bytes):
6e 65 74 64 65 76 73 69 6d 31 00 00 00 00 00 00 netdevsim1......
backtrace:
[<
000000005e2e5e26>] __kmalloc_node_track_caller+0x3a/0xb0
[<
0000000094ca4fc8>] kvasprintf+0xc3/0x160
[<
00000000aad09bcc>] kvasprintf_const+0x55/0x180
[<
000000009bac868d>] kobject_set_name_vargs+0x56/0x150
[<
000000007c1a5d70>] dev_set_name+0xbb/0xf0
[<
00000000ad0d126b>] device_add+0x1f8/0x1cb0
[<
00000000c222ae24>] new_device_store+0x3b6/0x5e0
[<
0000000043593421>] bus_attr_store+0x72/0xa0
[<
00000000cbb1833a>] sysfs_kf_write+0x106/0x160
[<
00000000d0dedb8a>] kernfs_fop_write_iter+0x3a8/0x5a0
[<
00000000770b66e2>] vfs_write+0x8f0/0xc80
[<
0000000078bb39be>] ksys_write+0x106/0x210
[<
00000000005e55a4>] do_syscall_64+0x35/0x80
[<
00000000eaa40bbc>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes:
40e4fe4ce115 ("netdevsim: move device registration and related code to bus.c")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221026015405.128795-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 27 Oct 2022 17:30:41 +0000 (10:30 -0700)]
Merge tag 'linux-can-fixes-for-6.1-
20221027' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-27
Anssi Hannula fixes the use of the completions in the kvaser_usb
driver.
Biju Das contributes 2 patches for the rcar_canfd driver. A IRQ storm
that can be triggered by high CAN bus load and channel specific IRQ
handlers are fixed.
Yang Yingliang fixes the j1939 transport protocol by moving a
kfree_skb() out of a spin_lock_irqsave protected section.
* tag 'linux-can-fixes-for-6.1-
20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb()
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
can: kvaser_usb: Fix possible completions during init_completion
====================
Link: https://lore.kernel.org/r/20221027114356.1939821-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rafał Miłecki [Thu, 27 Oct 2022 11:24:30 +0000 (13:24 +0200)]
net: broadcom: bcm4908_enet: update TX stats after actual transmission
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes:
4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 27 Oct 2022 17:16:56 +0000 (10:16 -0700)]
Merge branch 'ip-rework-the-fix-for-dflt-addr-selection-for-connected-nexthop'
Nicolas Dichtel says:
====================
ip: rework the fix for dflt addr selection for connected nexthop"
This series reworks the fix that is reverted in the second commit.
As Julian explained, nhc_scope is related to nhc_gw, it's not the scope of
the route.
====================
Link: https://lore.kernel.org/r/20221020100952.8748-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nicolas Dichtel [Thu, 20 Oct 2022 10:09:52 +0000 (12:09 +0200)]
nh: fix scope used to find saddr when adding non gw nh
As explained by Julian, fib_nh_scope is related to fib_nh_gw4, but
fib_info_update_nhc_saddr() needs the scope of the route, which is
the scope "before" fib_nh_scope, ie fib_nh_scope - 1.
This patch fixes the problem described in commit
747c14307214 ("ip: fix
dflt addr selection for connected nexthop").
Fixes:
597cfe4fc339 ("nexthop: Add support for IPv4 nexthops")
Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nicolas Dichtel [Thu, 20 Oct 2022 10:09:51 +0000 (12:09 +0200)]
Revert "ip: fix dflt addr selection for connected nexthop"
This reverts commit
747c14307214b55dbd8250e1ab44cad8305756f1.
As explained by Julian, nhc_scope is related to nhc_gw, not to the route.
Revert the original patch. The initial problem is fixed differently in the
next commit.
Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nicolas Dichtel [Thu, 20 Oct 2022 10:09:50 +0000 (12:09 +0200)]
Revert "ip: fix triggering of 'icmp redirect'"
This reverts commit
eb55dc09b5dd040232d5de32812cc83001a23da6.
The patch that introduces this bug is reverted right after this one.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 26 Oct 2022 00:15:24 +0000 (17:15 -0700)]
genetlink: limit the use of validation workarounds to old ops
During review of previous change another thing came up - we should
limit the use of validation workarounds to old commands.
Don't list the workarounds one by one, as we're rejecting all existing
ones. We can deal with the masking in the unlikely event that new flag
is added.
Link: https://lore.kernel.org/all/6ba9f727e555fd376623a298d5d305ad408c3d47.camel@sipsolutions.net/
Link: https://lore.kernel.org/r/20221026001524.1892202-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli [Tue, 25 Oct 2022 23:42:01 +0000 (16:42 -0700)]
net: bcmsysport: Indicate MAC is in charge of PHY PM
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT
driver essentially does exactly what mdio_bus_phy_resume() does by
calling phy_resume().
Fixes:
fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221025234201.2549360-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Yang Yingliang [Thu, 27 Oct 2022 09:12:37 +0000 (17:12 +0800)]
can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb()
It is not allowed to call kfree_skb() from hardware interrupt context
or with interrupts being disabled. The skb is unlinked from the queue,
so it can be freed after spin_unlock_irqrestore().
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20221027091237.2290111-1-yangyingliang@huawei.com
Cc: stable@vger.kernel.org
[mkl: adjust subject]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yang Yingliang [Tue, 25 Oct 2022 13:00:11 +0000 (21:00 +0800)]
net: ehea: fix possible memory leak in ehea_register_port()
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
Fixes:
1acf2318dd13 ("ehea: dynamic add / remove port")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221025130011.1071357-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 27 Oct 2022 10:31:45 +0000 (12:31 +0200)]
Merge branch 'openvswitch-syzbot-splat-fix-and-introduce-selftest'
Aaron Conole says:
====================
openvswitch: syzbot splat fix and introduce selftest
Syzbot recently caught a splat when dropping features from
openvswitch datapaths that are in-use. The WARN() call is
definitely too large a hammer for the situation, so change
to pr_warn.
Second patch in the series introduces a new selftest suite which
can help show that an issue is fixed. This change might be
more suited to net-next tree, so it has been separated out
as an additional patch and can be either applied to either tree
based on preference.
====================
Link: https://lore.kernel.org/r/20221025105018.466157-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Aaron Conole [Tue, 25 Oct 2022 10:50:18 +0000 (06:50 -0400)]
selftests: add openvswitch selftest suite
Previous commit resolves a WARN splat that can be difficult to reproduce,
but with the ovs-dpctl.py utility, it can be trivial. Introduce a test
case which creates a DP, and then downgrades the feature set. This will
include a utility 'ovs-dpctl.py' that can be extended to do additional
tests and diagnostics.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Aaron Conole [Tue, 25 Oct 2022 10:50:17 +0000 (06:50 -0400)]
openvswitch: switch from WARN to pr_warn
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com
Fixes:
44da5ae5fbea ("openvswitch: Drop user features if old user space attempted to create datapath")
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Marc Kleine-Budde [Thu, 27 Oct 2022 07:34:24 +0000 (09:34 +0200)]
Merge patch series "R-Car CAN-FD fixes"
Biju Das <biju.das.jz@bp.renesas.com> says:
This patch series fixes the below issues in R-Car CAN-FD driver.
1) Race condition in CAN driver under heavy CAN load condition
with both channels enabled results in IRQ storm on global FIFO
receive IRQ line.
2) Add channel specific TX interrupts handling for RZ/G2L SoC as it has
separate IRQ lines for each TX.
changes since v1: https://lore.kernel.org/all/
20221022081503.
1051257-1-biju.das.jz@bp.renesas.com
* Added check for IRQ active and enabled before handling the IRQ on a
particular channel.
Link: https://lore.kernel.org/all/20221025155657.1426948-1-biju.das.jz@bp.renesas.com
[mkl: adjust message, add link, take only patches 1 + 2, upstream 3 via can-next]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Biju Das [Tue, 25 Oct 2022 15:56:56 +0000 (16:56 +0100)]
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes:
76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Biju Das [Tue, 25 Oct 2022 15:56:55 +0000 (16:56 +0100)]
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes:
dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Mon, 10 Oct 2022 18:52:27 +0000 (20:52 +0200)]
can: kvaser_usb: Fix possible completions during init_completion
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes:
080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kunihiko Hayashi [Mon, 24 Oct 2022 07:22:27 +0000 (16:22 +0900)]
net: ethernet: ave: Fix MAC to be in charge of PHY PM
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes:
fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Juergen Borleis [Mon, 24 Oct 2022 08:05:52 +0000 (10:05 +0200)]
net: fec: limit register access on i.MX6UL
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes:
a51d3ab50702 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 27 Oct 2022 03:12:50 +0000 (20:12 -0700)]
Merge tag 'linux-can-fixes-for-6.1-
20221025' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-25
The 1st patch adds a missing cleanup call in the error path of the
probe function in mpc5xxx glue code for the mscan driver.
The 2nd patch adds a missing cleanup call in the error path of the
probe function of the mcp251x driver.
* tag 'linux-can-fixes-for-6.1-
20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path
can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path
====================
Link: https://lore.kernel.org/r/20221026075520.1502520-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 27 Oct 2022 00:44:10 +0000 (17:44 -0700)]
Merge tag 'perf-tools-fixes-for-v6.1-2022-10-26' of git://git./linux/kernel/git/acme/linux
Pull perf tool fixes from Arnaldo Carvalho de Melo:
- Fix some aspects of building with an older (than the one in the
kernel sources) libbpf present in a distro, when building with
LIBBPF_DYNAMIC=1.
- Fix errno setting races with event_fd and the signal handler in 'perf
record'.
- Fix Power10 hv-24x7 metric events when some events may have a zero
count based on system configuration.
- Do not fail Intel-PT misc test w/o libpython, just skip it.
- Fix incorrect arm64 Hisi hip08 L3 metrics (IF_BP_MISP_BR_RET,
IF_BP_MISP_BR_RET, IF_BP_MISP_BR_BL) due to mistakes in the
documentation used to generate the JSON files for these metrics.
- Fix auxtrace (Intel PT, ARM Coresight) address filter symbol name
match for modules, we need to skip the module name.
- Sync copies of files with the kernel sources, including ppc syscall
tables and assorted headers, some resulting in tools being able to
decode new network protocols (IPPROTO_L2TP) and statx masks
(STATX_DIOALIGN).
- Fix PMU name pai_crypto in the vendor events file (JSON) for s390.
- Fix man page build wrt perf-arm-coresight.txt as the build process
assumes files starting with 'perf-' are man pages, and this file
isn't one.
* tag 'perf-tools-fixes-for-v6.1-2022-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf vendor events arm64: Fix incorrect Hisi hip08 L3 metrics
perf auxtrace: Fix address filter symbol name match for modules
tools headers UAPI: Sync linux/perf_event.h with the kernel sources
tools headers cpufeatures: Sync with the kernel sources
tools headers uapi: Sync linux/stat.h with the kernel sources
tools include UAPI: Sync sound/asound.h copy with the kernel sources
tools headers uapi: Update linux/in.h copy
tools headers: Update the copy of x86's memcpy_64.S used in 'perf bench'
tools headers arm64: Sync arm64's cputype.h with the kernel sources
perf test: Do not fail Intel-PT misc test w/o libpython
perf list: Fix PMU name pai_crypto in perf list on s390
perf record: Fix event fd races
perf bpf: Fix build with libbpf 0.7.0 by checking if bpf_program__set_insns() is available
perf bpf: Fix build with libbpf 0.7.0 by adding prototype for bpf_load_program()
perf vendor events power10: Fix hv-24x7 metric events
perf docs: Fix man page build wrt perf-arm-coresight.txt
tools headers UAPI: Sync powerpc syscall tables with the kernel sources
Linus Torvalds [Thu, 27 Oct 2022 00:38:46 +0000 (17:38 -0700)]
Merge tag 'spi-fix-v6.1-rc2' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description"
* tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: aspeed: Fix window offset of CE1
spi: qup: support using GPIO as chip select line
spi: intel: Fix the offset to get the 64K erase opcode
spi: aspeed: Fix typo in mode_bits field for AST2600 platform
spi: mpc52xx: Replace NO_IRQ by 0
spi: spi-mem: Fix typo (of -> or)
spi: spi-gxp: fix typo in SPDX identifier line
spi: tegra210-quad: Fix combined sequence
Linus Torvalds [Wed, 26 Oct 2022 18:15:00 +0000 (11:15 -0700)]
Merge tag 'arc-6.1-fixes' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- fix for Page Table mem leak
- defconfig updates
- misc other fixes
* tag 'arc-6.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: fix leakage of memory allocated for PTE
arc: update config files
arc: iounmap() arg is volatile
arc: dts: Harmonize EHCI/OHCI DT nodes name
ARC: bitops: Change __fls to return unsigned long
ARC: Fix comment typo
ARC: Fix comment typo
Shang XiaoJing [Fri, 21 Oct 2022 10:50:33 +0000 (18:50 +0800)]
perf vendor events arm64: Fix incorrect Hisi hip08 L3 metrics
Commit
0cc177cfc95d565e ("perf vendor events arm64: Add Hisi hip08 L3
metrics") add L3 metrics of hip08, but some metrics (IF_BP_MISP_BR_RET,
IF_BP_MISP_BR_RET, IF_BP_MISP_BR_BL) have incorrect event number due to
the mistakes in document, which caused incorrect result. Fix the
incorrect metrics.
Before:
65,811,214,308 armv8_pmuv3_0/event=0x1014/ # 18.87 push_branch
# -40.19 other_branch
3,564,316,780 BR_MIS_PRED # 0.51 indirect_branch
# 21.81 pop_branch
After:
6,537,146,245 BR_MIS_PRED # 0.48 indirect_branch
# 0.47 pop_branch
# 0.00 push_branch
# 0.05 other_branch
Fixes:
0cc177cfc95d565e ("perf vendor events arm64: Add Hisi hip08 L3 metrics")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Acked-by: James Clark <james.clark@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221021105035.10000-2-shangxiaojing@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Wed, 26 Oct 2022 07:27:36 +0000 (10:27 +0300)]
perf auxtrace: Fix address filter symbol name match for modules
For modules, names from kallsyms__parse() contain the module name which
meant that module symbols did not match exactly by name.
Fix by matching the name string up to the separating tab character.
Fixes:
1b36c03e356936d6 ("perf record: Add support for using symbols in address filters")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026072736.2982-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Fri, 21 May 2021 19:00:31 +0000 (16:00 -0300)]
tools headers UAPI: Sync linux/perf_event.h with the kernel sources
To pick the changes in:
cfef80bad4cf79cd ("perf/uapi: Define PERF_MEM_SNOOPX_PEER in kernel header file")
ee3e88dfec23153d ("perf/mem: Introduce PERF_MEM_LVLNUM_{EXTN_MEM|IO}")
b4e12b2d70fd9ecc ("perf: Kill __PERF_SAMPLE_CALLCHAIN_EARLY")
There is a kernel patch pending that renames PERF_MEM_LVLNUM_EXTN_MEM to
PERF_MEM_LVLNUM_CXL, tooling this time is ahead of the kernel :-)
This thus partially addresses this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/perf_event.h' differs from latest version at 'include/uapi/linux/perf_event.h'
diff -u tools/include/uapi/linux/perf_event.h include/uapi/linux/perf_event.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/lkml/Y1k53KMdzypmU0WS@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Rolf Eike Beer [Fri, 21 Oct 2022 13:47:03 +0000 (15:47 +0200)]
rhashtable: make test actually random
The "random rhlist add/delete operations" actually wasn't very random, as all
cases tested the same bit. Since the later parts of this loop depend on the
first case execute this unconditionally, and then test on different bits for the
remaining tests. While at it only request as much random bits as are actually
used.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caleb Connolly [Mon, 24 Oct 2022 23:48:50 +0000 (00:48 +0100)]
net: ipa: don't configure IDLE_INDICATION on v3.1
IPA v3.1 doesn't support the IDLE_INDICATION_CFG register, this was
causing a harmless splat in ipa_idle_indication_cfg(), add a version
check to prevent trying to fetch this register on v3.1
Fixes:
6a244b75cfab ("net: ipa: introduce ipa_reg()")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Tested-by: Jami Kettunen <jami.kettunen@somainline.org>
Link: https://lore.kernel.org/r/20221024234850.4049778-1-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Caleb Connolly [Mon, 24 Oct 2022 21:03:32 +0000 (22:03 +0100)]
net: ipa: fix v3.1 resource limit masks
The resource group limits for IPA v3.1 mistakenly used 6 bit wide mask
values, when the hardware actually uses 8. Out of range values were
silently ignored before, so the IPA worked as expected. However the
new generalised register definitions introduce stricter checking here,
they now cause some splats and result in the value 0 being written
instead. Fix the limit bitmask widths so that the correct values can be
written.
Fixes:
1c418c4a929c ("net: ipa: define resource group/type IPA register fields")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Tested-by: Jami Kettunen <jami.kettunen@somainline.org>
Link: https://lore.kernel.org/r/20221024210336.4014983-2-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Caleb Connolly [Mon, 24 Oct 2022 21:03:31 +0000 (22:03 +0100)]
net: ipa: fix v3.5.1 resource limit max values
Some resource limits on IPA v3.5.1 have their max values set to
255, this causes a few splats in ipa_reg_encode and prevents the
IPA from booting properly. The limits are all 6 bits wide so
adjust the max values to 63.
Fixes:
1c418c4a929c ("net: ipa: define resource group/type IPA register fields")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20221024210336.4014983-1-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yang Yingliang [Mon, 24 Oct 2022 13:13:38 +0000 (21:13 +0800)]
net: ksz884x: fix missing pci_disable_device() on error in pcidev_init()
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Fixes:
8ca86fd83eae ("net: Micrel KSZ8841/2 PCI Ethernet driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Slawomir Laba [Mon, 24 Oct 2022 10:05:26 +0000 (03:05 -0700)]
i40e: Fix flow-type by setting GL_HASH_INSET registers
Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.
Fixes:
eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sylwester Dziedziuch [Mon, 24 Oct 2022 10:05:25 +0000 (03:05 -0700)]
i40e: Fix VF hang when reset is triggered on another VF
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes:
3ba9bcb4b68f ("i40e: add locking around VF reset")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Slawomir Laba [Mon, 24 Oct 2022 10:05:24 +0000 (03:05 -0700)]
i40e: Fix ethtool rx-flow-hash setting for X722
When enabling flow type for RSS hash via ethtool:
ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes:
eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 24 Oct 2022 02:01:24 +0000 (19:01 -0700)]
ipv6: ensure sane device mtu in tunnels
Another syzbot report [1] with no reproducer hints
at a bug in ip6_gre tunnel (dev:ip6gretap0)
Since ipv6 mcast code makes sure to read dev->mtu once
and applies a sanity check on it (see commit
b9b312a7a451
"ipv6: mcast: better catch silly mtu values"), a remaining
possibility is that a layer is able to set dev->mtu to
an underflowed value (high order bit set).
This could happen indeed in ip6gre_tnl_link_config_route(),
ip6_tnl_link_config() and ipip6_tunnel_bind_dev()
Make sure to sanitize mtu value in a local variable before
it is written once on dev->mtu, as lockless readers could
catch wrong temporary value.
[1]
skbuff: skb_over_panic: text:
ffff80000b7a2f38 len:40 put:40 head:
ffff000149dcf200 data:
ffff000149dcf2b0 tail:0xd8 end:0xc0 dev:ip6gretap0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:120
Internal error: Oops - BUG:
00000000f2000800 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 10241 Comm: kworker/1:1 Not tainted
6.0.0-rc7-syzkaller-18095-gbbed346d5a96 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/30/2022
Workqueue: mld mld_ifc_work
pstate:
60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : skb_panic+0x4c/0x50 net/core/skbuff.c:116
lr : skb_panic+0x4c/0x50 net/core/skbuff.c:116
sp :
ffff800020dd3b60
x29:
ffff800020dd3b70 x28:
0000000000000000 x27:
ffff00010df2a800
x26:
00000000000000c0 x25:
00000000000000b0 x24:
ffff000149dcf200
x23:
00000000000000c0 x22:
00000000000000d8 x21:
ffff80000b7a2f38
x20:
ffff00014c2f7800 x19:
0000000000000028 x18:
00000000000001a9
x17:
0000000000000000 x16:
ffff80000db49158 x15:
ffff000113bf1a80
x14:
0000000000000000 x13:
00000000ffffffff x12:
ffff000113bf1a80
x11:
ff808000081c0d5c x10:
0000000000000000 x9 :
73f125dc5c63ba00
x8 :
73f125dc5c63ba00 x7 :
ffff800008161d1c x6 :
0000000000000000
x5 :
0000000000000080 x4 :
0000000000000001 x3 :
0000000000000000
x2 :
ffff0001fefddcd0 x1 :
0000000100000000 x0 :
0000000000000089
Call trace:
skb_panic+0x4c/0x50 net/core/skbuff.c:116
skb_over_panic net/core/skbuff.c:125 [inline]
skb_put+0xd4/0xdc net/core/skbuff.c:2049
ip6_mc_hdr net/ipv6/mcast.c:1714 [inline]
mld_newpack+0x14c/0x270 net/ipv6/mcast.c:1765
add_grhead net/ipv6/mcast.c:1851 [inline]
add_grec+0xa20/0xae0 net/ipv6/mcast.c:1989
mld_send_cr+0x438/0x5a8 net/ipv6/mcast.c:2115
mld_ifc_work+0x38/0x290 net/ipv6/mcast.c:2653
process_one_work+0x2d8/0x504 kernel/workqueue.c:2289
worker_thread+0x340/0x610 kernel/workqueue.c:2436
kthread+0x12c/0x158 kernel/kthread.c:376
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860
Code:
91011400 aa0803e1 a90027ea 94373093 (
d4210000)
Fixes:
c12b395a4664 ("gre: Support GRE over IPv6")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221024020124.3756833-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Li Zetao [Mon, 24 Oct 2022 15:44:21 +0000 (23:44 +0800)]
fs/binfmt_elf: Fix memory leak in load_elf_binary()
There is a memory leak reported by kmemleak:
unreferenced object 0xffff88817104ef80 (size 224):
comm "xfs_admin", pid 47165, jiffies
4298708825 (age 1333.476s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
60 a8 b3 00 81 88 ff ff a8 10 5a 00 81 88 ff ff `.........Z.....
backtrace:
[<
ffffffff819171e1>] __alloc_file+0x21/0x250
[<
ffffffff81918061>] alloc_empty_file+0x41/0xf0
[<
ffffffff81948cda>] path_openat+0xea/0x3d30
[<
ffffffff8194ec89>] do_filp_open+0x1b9/0x290
[<
ffffffff8192660e>] do_open_execat+0xce/0x5b0
[<
ffffffff81926b17>] open_exec+0x27/0x50
[<
ffffffff81a69250>] load_elf_binary+0x510/0x3ed0
[<
ffffffff81927759>] bprm_execve+0x599/0x1240
[<
ffffffff8192a997>] do_execveat_common.isra.0+0x4c7/0x680
[<
ffffffff8192b078>] __x64_sys_execve+0x88/0xb0
[<
ffffffff83bbf0a5>] do_syscall_64+0x35/0x80
If "interp_elf_ex" fails to allocate memory in load_elf_binary(),
the program will take the "out_free_ph" error handing path,
resulting in "interpreter" file resource is not released.
Fix it by adding an error handing path "out_free_file", which will
release the file resource when "interp_elf_ex" failed to allocate
memory.
Fixes:
0693ffebcfe5 ("fs/binfmt_elf.c: allocate less for static executable")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221024154421.982230-1-lizetao1@huawei.com
Bernd Edlinger [Mon, 7 Jun 2021 13:54:27 +0000 (15:54 +0200)]
exec: Copy oldsighand->action under spin-lock
unshare_sighand should only access oldsighand->action
while holding oldsighand->siglock, to make sure that
newsighand->action is in a consistent state.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Cc: stable@vger.kernel.org
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/AM8PR10MB470871DEBD1DED081F9CC391E4389@AM8PR10MB4708.EURPRD10.PROD.OUTLOOK.COM
Kees Cook [Thu, 6 Oct 2022 23:00:17 +0000 (16:00 -0700)]
overflow: Refactor test skips for Clang-specific issues
Convert test exclusion into test skipping. This brings the logic for
why a test is being skipped into the test itself, instead of having to
spread ifdefs around the code. This will make cleanup easier as minimum
tests get raised. Drop __maybe_unused so missed tests will be noticed
again and clean up whitespace.
For example, clang-11 on i386:
[15:52:32] ================== overflow (18 subtests) ==================
[15:52:32] [PASSED] u8_u8__u8_overflow_test
[15:52:32] [PASSED] s8_s8__s8_overflow_test
[15:52:32] [PASSED] u16_u16__u16_overflow_test
[15:52:32] [PASSED] s16_s16__s16_overflow_test
[15:52:32] [PASSED] u32_u32__u32_overflow_test
[15:52:32] [PASSED] s32_s32__s32_overflow_test
[15:52:32] [SKIPPED] u64_u64__u64_overflow_test
[15:52:32] [SKIPPED] s64_s64__s64_overflow_test
[15:52:32] [SKIPPED] u32_u32__int_overflow_test
[15:52:32] [PASSED] u32_u32__u8_overflow_test
[15:52:32] [PASSED] u8_u8__int_overflow_test
[15:52:32] [PASSED] int_int__u8_overflow_test
[15:52:32] [PASSED] shift_sane_test
[15:52:32] [PASSED] shift_overflow_test
[15:52:32] [PASSED] shift_truncate_test
[15:52:32] [PASSED] shift_nonsense_test
[15:52:32] [PASSED] overflow_allocation_test
[15:52:32] [PASSED] overflow_size_helpers_test
[15:52:32] ==================== [PASSED] overflow =====================
[15:52:32] ============================================================
[15:52:32] Testing complete. Ran 18 tests: passed: 15, skipped: 3
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Tom Rix <trix@redhat.com>
Cc: Daniel Latypov <dlatypov@google.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: llvm@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20221006230017.1833458-1-keescook@chromium.org
Nick Desaulniers [Thu, 6 Oct 2022 17:17:51 +0000 (10:17 -0700)]
overflow: disable failing tests for older clang versions
Building the overflow kunit tests with clang-11 fails with:
$ ./tools/testing/kunit/kunit.py run --arch=arm --make_options LLVM=1 \
overflow
...
ld.lld: error: undefined symbol: __mulodi4
...
Clang 11 and earlier generate unwanted libcalls for signed output,
unsigned input.
Disable these tests for now, but should these become used in the kernel
we might consider that as justification for dropping clang-11 support.
Keep the clang-11 build alive a little bit longer.
Avoid -Wunused-function warnings via __maybe_unused. To test W=1:
$ make LLVM=1 -j128 defconfig
$ ./scripts/config -e KUNIT -e KUNIT_ALL
$ make LLVM=1 -j128 olddefconfig lib/overflow_kunit.o W=1
Link: https://github.com/ClangBuiltLinux/linux/issues/1711
Link: https://github.com/llvm/llvm-project/commit/3203143f1356a4e4e3ada231156fc6da6e1a9f9d
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221006171751.3444575-1-ndesaulniers@google.com
Kees Cook [Mon, 26 Sep 2022 19:45:32 +0000 (12:45 -0700)]
overflow: Fix kern-doc markup for functions
Fix the kern-doc markings for several of the overflow helpers and move
their location into the core kernel API documentation, where it belongs
(it's not driver-specific).
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: linux-hardening@vger.kernel.org
Reviewed-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Arnaldo Carvalho de Melo [Thu, 1 Jul 2021 16:39:15 +0000 (13:39 -0300)]
tools headers cpufeatures: Sync with the kernel sources
To pick the changes from:
257449c6a50298bd ("x86/cpufeatures: Add LbrExtV2 feature bit")
This only causes these perf files to be rebuilt:
CC /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
CC /tmp/build/perf/bench/mem-memset-x86-64-asm.o
And addresses this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandipan Das <sandipan.das@amd.com>
Link: https://lore.kernel.org/lkml/Y1g6vGPqPhOrXoaN@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Mon, 8 Jun 2020 14:32:48 +0000 (11:32 -0300)]
tools headers uapi: Sync linux/stat.h with the kernel sources
To pick the changes from:
825cf206ed510c4a ("statx: add direct I/O alignment information")
That add a constant that was manually added to tools/perf/trace/beauty/statx.c,
at some point this should move to the shell based automated way.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/stat.h' differs from latest version at 'include/uapi/linux/stat.h'
diff -u tools/include/uapi/linux/stat.h include/uapi/linux/stat.h
Cc: Eric Biggers <ebiggers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/Y1gGQL5LonnuzeYd@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Wed, 12 Feb 2020 14:04:23 +0000 (11:04 -0300)]
tools include UAPI: Sync sound/asound.h copy with the kernel sources
Picking the changes from:
69ab6f5b00b1804e ("ALSA: Remove some left-over license text in include/uapi/sound/")
Which entails no changes in the tooling side as it doesn't introduce new
SNDRV_PCM_IOCTL_ ioctls.
To silence this perf tools build warning:
Warning: Kernel ABI header at 'tools/include/uapi/sound/asound.h' differs from latest version at 'include/uapi/sound/asound.h'
diff -u tools/include/uapi/sound/asound.h include/uapi/sound/asound.h
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Thu, 19 Mar 2020 14:42:56 +0000 (11:42 -0300)]
tools headers uapi: Update linux/in.h copy
To get the changes in:
65b32f801bfbc54d ("uapi: move IPPROTO_L2TP to in.h")
5854a09b49574da5 ("net/ipv4: Use __DECLARE_FLEX_ARRAY() helper")
That ends up automatically adding the new IPPROTO_L2TP to the socket
args beautifiers:
$ tools/perf/trace/beauty/socket.sh > before
$ cp include/uapi/linux/in.h tools/include/uapi/linux/in.h
$ tools/perf/trace/beauty/socket.sh > after
$ diff -u before after
--- before 2022-10-25 12:17:02.
577892416 -0300
+++ after 2022-10-25 12:17:10.
806113033 -0300
@@ -20,6 +20,7 @@
[98] = "ENCAP",
[103] = "PIM",
[108] = "COMP",
+ [115] = "L2TP",
[132] = "SCTP",
[136] = "UDPLITE",
[137] = "MPLS",
$
Now 'perf trace' will decode that 115 into "L2TP" and it will also be
possible to use it in tracepoint filter expressions.
Addresses this tools/perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Wojciech Drewek <wojciech.drewek@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/lkml/Y1f%2FGe6vjQrGjYiK@kernel.org/
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Mon, 2 Dec 2019 14:40:57 +0000 (11:40 -0300)]
tools headers: Update the copy of x86's memcpy_64.S used in 'perf bench'
We also need to add SYM_TYPED_FUNC_START() to util/include/linux/linkage.h
and update tools/perf/check_headers.sh to ignore the include cfi_types.h
line when checking if the kernel original files drifted from the copies
we carry.
This is to get the changes from:
ccace936eec7b805 ("x86: Add types to indirectly called assembly functions")
Addressing these tools/perf build warnings:
Warning: Kernel ABI header at 'tools/arch/x86/lib/memcpy_64.S' differs from latest version at 'arch/x86/lib/memcpy_64.S'
diff -u tools/arch/x86/lib/memcpy_64.S arch/x86/lib/memcpy_64.S
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/lkml/Y1f3VRIec9EBgX6F@kernel.org/
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>