OSDN Git Service
Olof Johansson [Tue, 11 Jun 2013 04:50:49 +0000 (21:50 -0700)]
Merge tag 'pcie_kw-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11 (round 2)
- kirkwood
- migrate Netgear ReadyNAS Duo v2 to pcie DT init
* tag 'pcie_kw-3.11-2' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: NETGEAR ReadyNAS Duo v2 init PCIe via DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 8 Jun 2013 00:01:42 +0000 (17:01 -0700)]
Merge tag 'zynq-clk-for-3.11' of git://git.xilinx.com/linux-xlnx into next/soc
From Michal Simek:
arm: Xilinx Zynq clock changes for v3.11
Change Xilinx Zynq DT clock description which reflects logical abstraction
of Zynq's clock tree.
- Refactor PLL driver
- Use new clock controller driver
- Change timer and uart drivers
* tag 'zynq-clk-for-3.11' of git://git.xilinx.com/linux-xlnx:
clk: zynq: Remove deprecated clock code
arm: zynq: Migrate platform to clock controller
clk: zynq: Add clock controller driver
clk: zynq: Factor out PLL driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Mon, 3 Jun 2013 13:15:36 +0000 (15:15 +0200)]
drivers/bus: arm-cci: fix combined ARMv6+v7 build
When we build a kernel with support for both ARMv6 and ARMv7,
gas is trying to be helpful by pointing out that the arm-cci
driver would not work on ARMv6:
/tmp/ccu1LDeU.s: Assembler messages:
/tmp/ccu1LDeU.s:450: Error: selected processor does not support ARM mode `wfi '
/tmp/ccu1LDeU.s:451: Error: selected processor does not support ARM mode `wfe '
make[4]: *** [drivers/bus/arm-cci.o] Error 1
We know that the driver will only be used on ARMv7, hence we
can annotate the inline assembly listing to allow those instructions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Dave Martin <dave.martin@linaro.org>
Olof Johansson [Sat, 1 Jun 2013 06:39:35 +0000 (23:39 -0700)]
Merge branch 'VExpress_DCSCB' of git://git.linaro.org/people/nico/linux into next/soc
From Nicolas Pitre:
This is the first MCPM backend submission for VExpress running on RTSM
aka Fast Models implementing the big.LITTLE system architecture. This
enables SMP secondary boot as well as CPU hotplug on this platform.
A big prerequisite for this support is the CCI driver from Lorenzo
included in this pull request.
Also included is Rob Herring's set_auxcr/get_auxcr allowing nicer code.
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'VExpress_DCSCB' of git://git.linaro.org/people/nico/linux:
ARM: vexpress: Select multi-cluster SMP operation if required
ARM: vexpress/dcscb: handle platform coherency exit/setup and CCI
ARM: vexpress/dcscb: do not hardcode number of CPUs per cluster
ARM: vexpress/dcscb: add CPU use counts to the power up/down API implementation
ARM: vexpress: introduce DCSCB support
ARM: introduce common set_auxcr/get_auxcr functions
drivers/bus: arm-cci: function to enable CCI ports from early boot code
drivers: bus: add ARM CCI support
Olof Johansson [Sat, 1 Jun 2013 06:37:22 +0000 (23:37 -0700)]
Merge branch 'depends/rmk-devel-stable' into next/soc
Pulling in base dependencies from rmk's devel-stable branch needed by the
CCI patches for vexpress.
Signed-off-by: Olof Johansson <olof@lixom.net>
* depends/rmk-devel-stable:
ARM: Enable selection of SMP operations at boot time
arm: introduce psci_smp_ops
ARM: ARMv7-M: implement read_cpuid_ext
ARM: ARMv7-M: Allow the building of new kernel port
ARM: ARMv7-M: Add support for exception handling
ARM: Add base support for ARMv7-M
Olof Johansson [Sat, 1 Jun 2013 06:23:25 +0000 (23:23 -0700)]
Merge tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu clock restructuring for v3.11
- clk: mvebu
- reorganize by SoC to remove built up #ifdefs
- add clk flags per clock gate
* tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux:
clk: mvebu: disintegrate obsolete file
ARM: mvebu: move DT boards to SoC-centric clock init
ARM: kirkwood: move DT boards to SoC-centric clock init
ARM: dove: move DT boards to SoC-centric clock init
clk: mvebu: add Armada XP SoC-centric clock init
clk: mvebu: add Armada 370 SoC-centric clock init
clk: mvebu: add Kirkwood SoC-centric clock init
clk: mvebu: add Dove SoC-centric clock init
clk: mvebu: add common clock functions for core clk and clk gating
clk: mvebu: introduce per-clock-gate flags
Olof Johansson [Sat, 1 Jun 2013 06:20:52 +0000 (23:20 -0700)]
Merge tag 'pcie_bridge-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (bridge) for v3.11
- mvebu
- allow enumeration of devices beyond physical bridges
- remove faking the slot location
- fix status register emulation
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_bridge-3.11' of git://git.infradead.org/users/jcooper/linux:
pci: mvebu: fix the emulation of the status register
pci: mvebu: allow the enumeration of devices beyond physical bridges
pci: mvebu: no longer fake the slot location of downstream devices
Olof Johansson [Sat, 1 Jun 2013 06:17:39 +0000 (23:17 -0700)]
Merge tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: convert db-
88f6281/db-
88f6282 to the Device Tree
arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interface
arm: kirkwood: convert MPL CEC4 to use DT for the PCIe interface
arm: kirkwood: convert Iomega Iconnect to use DT for the PCIe interface
arm: kirkwood: add SoC-level Device Tree data for PCIe interfaces
arm: kirkwood: move PCIe window init to legacy driver
pci: mvebu: enable driver usage on Kirkwood
Olof Johansson [Sat, 1 Jun 2013 06:13:24 +0000 (23:13 -0700)]
Merge tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
PCI-e driver for mvebu.
* tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux:
pci: mvebu: fix return value check in mvebu_pcie_probe()
arm: mvebu: PCIe support is now available on mvebu
pci: PCIe driver for Marvell Armada 370/XP systems
clk: mvebu: add more PCIe clocks for Armada XP
clk: mvebu: create parent-child relation for PCIe clocks on Armada 370
of/pci: Add of_pci_parse_bus_range() function
of/pci: Add of_pci_get_devfn() function
of/pci: Provide support for parsing PCI DT ranges property
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 1 Jun 2013 05:46:02 +0000 (22:46 -0700)]
Merge tag 'defconfig-3.11-3' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper, mvebu defconfig changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'defconfig-3.11-3' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: Enable cpufreq and ondemand on kirkwood_defconfig
arm: kirkwood: update defconfig with PCIe driver and board updates
arm: mvebu: update defconfig with PCI and USB support
ARM: Kirkwood: Enable USB 3.0 in kirkwood_defconfig
ARM: kirkwood: enable Sheevaplug DT in defconfig
ARM: mvebu: Add support for USB storage class in mvebu_defconfig
Olof Johansson [Sat, 1 Jun 2013 05:39:49 +0000 (22:39 -0700)]
Merge tag 'soc-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper, mvebu soc changes for v3.11
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'soc-3.11-2' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: Instantiate cpufreq driver
arm: kirkwood: use the default of match table
Jon Medhurst [Wed, 30 Jan 2013 09:12:55 +0000 (09:12 +0000)]
ARM: vexpress: Select multi-cluster SMP operation if required
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Dave Martin [Tue, 17 Jul 2012 13:25:44 +0000 (14:25 +0100)]
ARM: vexpress/dcscb: handle platform coherency exit/setup and CCI
Add the required code to properly handle race free platform coherency exit
to the DCSCB power down method.
The power_up_setup callback is used to enable the CCI interface for
the cluster being brought up. This must be done in assembly before
the kernel environment is entered.
Thanks to Achin Gupta and Nicolas Pitre for their help and
contributions.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Nicolas Pitre [Wed, 18 Jul 2012 20:41:16 +0000 (16:41 -0400)]
ARM: vexpress/dcscb: do not hardcode number of CPUs per cluster
If 4 CPUs are assumed, the A15x1-A7x1 model configuration would never
shut down the initial cluster as the 0xf reset bit mask will never be
observed. Let's construct this mask based on the provided information
in the DCSCB config register for the number of CPUs per cluster.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Nicolas Pitre [Tue, 17 Jul 2012 02:07:10 +0000 (22:07 -0400)]
ARM: vexpress/dcscb: add CPU use counts to the power up/down API implementation
It is possible for a CPU to be told to power up before it managed
to power itself down. Solve this race with a usage count to deal
with this possibility as mandated by the MCPM API definition.
Signed-off-by: nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Nicolas Pitre [Thu, 3 May 2012 00:56:52 +0000 (20:56 -0400)]
ARM: vexpress: introduce DCSCB support
This adds basic CPU and cluster reset controls on RTSM for the
A15x4-A7x4 model configuration using the Dual Cluster System
Configuration Block (DCSCB).
The cache coherency interconnect (CCI) is not handled yet.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Rob Herring [Wed, 16 Jan 2013 23:57:33 +0000 (17:57 -0600)]
ARM: introduce common set_auxcr/get_auxcr functions
Move the private set_auxcr/get_auxcr functions from
drivers/cpuidle/cpuidle-calxeda.c so they can be used across platforms.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Nicolas Pitre [Wed, 22 May 2013 03:34:41 +0000 (23:34 -0400)]
drivers/bus: arm-cci: function to enable CCI ports from early boot code
This provides cci_enable_port_for_self(). This is the counterpart to
cci_disable_port_by_cpu(self).
This is meant to be called from the MCPM machine specific power_up_setup
callback code when the appropriate affinity level needs to be initialized.
The code therefore has to be position independent as the MMU is still off
and it cannot rely on any stack space.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Lorenzo Pieralisi [Fri, 13 Jul 2012 14:55:52 +0000 (15:55 +0100)]
drivers: bus: add ARM CCI support
On ARM multi-cluster systems coherency between cores running on
different clusters is managed by the cache-coherent interconnect (CCI).
It allows broadcasting of TLB invalidates and memory barriers and it
guarantees cache coherency at system level through snooping of slave
interfaces connected to it.
This patch enables the basic infrastructure required in Linux to handle and
programme the CCI component.
Non-local variables used by the CCI management functions called by power
down function calls after disabling the cache must be flushed out to main
memory in advance, otherwise incoherency of those values may occur if they
are sitting in the cache of some other CPU when power down functions
execute. Driver code ensures that relevant data structures are flushed
from inner and outer caches after the driver probe is completed.
CCI slave port resources are linked to set of CPUs through bus masters
phandle properties that link the interface resources to masters node in
the device tree.
Documentation describing the CCI DT bindings is provided with the patch.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Andrew Lunn [Sun, 27 Jan 2013 10:07:23 +0000 (11:07 +0100)]
arm: kirkwood: Instantiate cpufreq driver
Register a platform driver structure for the cpufreq driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Tue, 28 May 2013 15:13:18 +0000 (15:13 +0000)]
clk: mvebu: disintegrate obsolete file
Switch from function-centric to soc-centric clock drivers now makes
a bunch of files obsolete. This deletes all files and Kconfig options
that are not required anymore.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:09 +0000 (03:08 +0200)]
ARM: mvebu: move DT boards to SoC-centric clock init
SoC centric clock init for Armada 370/XP can be used by calling of_clk_init.
Use it and get rid of mvebu_clocks_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:08 +0000 (03:08 +0200)]
ARM: kirkwood: move DT boards to SoC-centric clock init
SoC centric clock init for Kirkwood can be used by calling of_clk_init.
Use it and get rid of mvebu_clocks_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:07 +0000 (03:08 +0200)]
ARM: dove: move DT boards to SoC-centric clock init
SoC centric clock init for Dove can be used by calling of_clk_init.
Use it and get rid of mvebu_clocks_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:06 +0000 (03:08 +0200)]
clk: mvebu: add Armada XP SoC-centric clock init
This is moving core clock and clock gating init for Armada XP to
its own file and adds a Kconfig option. Also init functions are added
and declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:05 +0000 (03:08 +0200)]
clk: mvebu: add Armada 370 SoC-centric clock init
This is moving core clock and clock gating init for Armada 370 to
its own file and adds a Kconfig option. Also init functions are added
and declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:04 +0000 (03:08 +0200)]
clk: mvebu: add Kirkwood SoC-centric clock init
This is moving core clock and clock gating init for Kirkwood to its
own file and adds a Kconfig option. Also init functions are added and
declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:03 +0000 (03:08 +0200)]
clk: mvebu: add Dove SoC-centric clock init
This is moving core clock and clock gating init for Dove to its own
file and adds a Kconfig option. Also init functions are added and
declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:02 +0000 (03:08 +0200)]
clk: mvebu: add common clock functions for core clk and clk gating
Based on the current common functions for core clocks and clock
gating control, new common functions are joined in a single file.
Given the opportunity, names of functions and structs are unified,
and also a Kconfig entry is added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 11 May 2013 01:08:01 +0000 (03:08 +0200)]
clk: mvebu: introduce per-clock-gate flags
Clock gates found on MVEBU SoCs get registered by a common function.
To allow specific SoCs to provide tweaks introduce flags to the clock
gate descriptor instead of filling up the common function SoC specific
tweaks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Arnaud Ebalard [Wed, 29 May 2013 11:37:52 +0000 (11:37 +0000)]
arm: kirkwood: NETGEAR ReadyNAS Duo v2 init PCIe via DT
Now that the mvebu-pcie driver is in place and enabled for kirkwood,
convert to initializing PCIe via devicetree.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:37:01 +0000 (15:37 +0200)]
arm: kirkwood: convert db-
88f6281/db-
88f6282 to the Device Tree
This commit converts the Marvell DB-
88F6281/DB-
88F6282 board to the
Device Tree. In fact, the code was supporting two different boards:
one with the 6281 SoC variant, and one with the 6282 SoC variant. The
difference between the two being that the 6281 has one PCIe interface,
and the 6282 has two PCIe interfaces.
In order to handle that with the Device Tree, we create a
'kirkwood-db.dtsi' file that contains the definitions common to both
boards, and 'kirkwood-db-
88f6281.dts' and 'kirkwood-db-
88f6282.dts'
for the definitions specific to each board. This is similar to what is
done for the QNAP TS219 Kirkwood platform.
We have kept one single Kconfig option, just like it was before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:37:00 +0000 (15:37 +0200)]
arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
Now that the PCIe mvebu driver is usable on Kirkwood, use it instead
of the legacy PCIe code, since it allows to describe the PCIe
interfaces in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:36:59 +0000 (15:36 +0200)]
arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interface
Now that the PCIe mvebu driver is usable on Kirkwood, use it instead
of the legacy PCIe code, since it allows to describe the PCIe
interfaces in the Device Tree.
Since it was the only device left that prevented this platform to use
the Device Tree only, we remove the board-nsa310.c file and the
related Kconfig/Makefile bits.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:36:58 +0000 (15:36 +0200)]
arm: kirkwood: convert MPL CEC4 to use DT for the PCIe interface
Now that the PCIe mvebu driver is usable on Kirkwood, use it instead
of the legacy PCIe code, since it allows to describe the PCIe
interfaces in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:36:57 +0000 (15:36 +0200)]
arm: kirkwood: convert Iomega Iconnect to use DT for the PCIe interface
Now that the PCIe mvebu driver is usable on Kirkwood, use it instead
of the legacy PCIe code, since it allows to describe the PCIe
interfaces in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:36:56 +0000 (15:36 +0200)]
arm: kirkwood: add SoC-level Device Tree data for PCIe interfaces
This commit adds Device Tree details to enable the PCIe interfaces on
Kirkwood. The 6281 has one PCIe interface, the 6282 has two PCIe
interfaces.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:36:55 +0000 (15:36 +0200)]
arm: kirkwood: move PCIe window init to legacy driver
Since we are going to enable the usage of the mvebu PCIe driver on
Kirkwood, we don't want the PCIe windows to be unconditionally created
by kirkwood_setup_wins(). Therefore, we move the PCIe window
initialization into the legacy PCIe driver
(arch/arm/mach-kirkwood/pcie.c).
The platforms using the legacy driver will see their windows
statically allocated by
arch/arm/mach-kirkwood/pcie.c:kirkwood_pcie_init(). The platforms
using the new driver in drivers/pci/ will see their windows
dynamically allocated directly by the driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Wed, 15 May 2013 13:36:54 +0000 (15:36 +0200)]
pci: mvebu: enable driver usage on Kirkwood
We allow the pci-mvebu driver to be compiled on the Kirkwood platform,
and add the 'marvell,kirkwood-pcie' as a compatible string supported
by the driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 23 May 2013 14:32:53 +0000 (16:32 +0200)]
pci: mvebu: fix the emulation of the status register
The status register of the PCI configuration space of PCI-to-PCI
bridges contain some read-only bits, and so write-1-to-clear bits. So,
the Linux PCI core sometimes writes 0xffff to this status register,
and in the current PCI-to-PCI bridge emulation code of the Marvell
driver, we do take all those 1s being written. Even the read-only bits
are being overwritten.
For now, all the read-only bits should be emulated to have the zero
value.
The other bits, that are write-1-to-clear bits are used to report
various kind of errors, and are never set by the emulated bridge, so
there is no need to support this write-1-to-clear bits mechanism.
As a conclusion, the easiest solution is to simply emulate this status
register by returning zero when read, and ignore the writes to it.
This has two visible effects:
* The devsel is no longer 'unknown' in, i.e
Flags: bus master, 66MHz, user-definable features, ?? devsel, latency 0
becomes:
Flags: bus master, 66MHz, user-definable features, fast devsel, latency 0
in lspci -v.
This was caused by a value of 11b being read for devsel, which is
an invalid value. This 11b value being read was due to a previous
write of 0xffff into the status register.
* The capability list is no longer broken, because we indicate to the
Linux PCI core that we don't have a Capabilities Pointer in the PCI
configuration space of this bridge. The following message is
therefore no longer visible in lspci -v:
Capabilities: [fc] <chain broken>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 23 May 2013 14:32:52 +0000 (16:32 +0200)]
pci: mvebu: allow the enumeration of devices beyond physical bridges
Until now, the Marvell PCIe driver was only allowing the enumeration
of the devices in the secondary bus of the emulated PCI-to-PCI
bridge. This works fine when a PCIe device is directly connected into
a PCIe slot of the Marvell board.
However, when the device connected in the PCIe slot is a physical PCIe
bridge, beyond which a real PCIe device is connected, it no longer
worked, as the driver was preventing the Linux PCI core from seeing
such devices.
This commit fixes that by ensuring that configuration transactions on
subordinate busses are properly forwarded on the right PCIe interface.
Thanks to this patch, a PCIe card beyond a PCIe bridge, itself beyond
the emulated PCI-to-PCI bridge is properly detected, with the
following layout:
-[0000:00]-+-01.0-[01]----00.0
+-09.0-[02-07]----00.0-[03-07]--+-01.0-[04]--
| +-05.0-[05]--
| +-07.0-[06]--
| \-09.0-[07]----00.0
\-0a.0-[08]----00.0
Where the PCIe interface that sits beyond the emulated PCI-to-PCI
bridge at 09.0 allows to access the secondary bus 02, on which there
is a PCIe bridge that allows to access the 3 to 7 busses, that are
subordinates to this bridge. And on one of this bus (bus 7), there is
one real PCIe device connected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Thu, 23 May 2013 14:32:51 +0000 (16:32 +0200)]
pci: mvebu: no longer fake the slot location of downstream devices
By default, the Marvell hardware, for each PCIe interface, exhibits
the following devices:
* On slot 0, a "Marvell Memory controller", identical on all PCIe
interfaces, and which isn't useful when the Marvell SoC is the PCIe
root complex (i.e, the normal case when we run Linux on the Marvell
SoC).
* On slot 1, the real PCIe card connected into the PCIe slot of the
board.
So, what the Marvell PCIe driver was doing in its PCI-to-PCI bridge
emulation is that when the Linux PCI core was trying to access the
device in slot 0, we were in fact forwarding the configuration
transaction to the device in slot 1. For all other slots, we were
telling the Linux PCI core that there was no device connected.
However, new versions of bootloaders from Marvell change the default
PCIe configuration, and make the real device appear in slot 0, and the
"Marvell Memory controller" in slot 1.
Therefore, this commit modifies the Marvell PCIe driver to adjust the
PCIe hardware configuration to make sure that this behavior (real
device in slot 0, "Marvell Memory controller" in slot 1) is the one
we'll see regardless of what the bootloader has done. It allows to
remove the little hack that was forwarding configuration transactions
on slot 0 to slot 1, which is nice.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Wei Yongjun [Mon, 27 May 2013 03:38:41 +0000 (11:38 +0800)]
pci: mvebu: fix return value check in mvebu_pcie_probe()
In case of error, function of_clk_get_by_name() returns
ERR_PTR() never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Soren Brinkmann [Mon, 13 May 2013 17:46:39 +0000 (10:46 -0700)]
clk: zynq: Remove deprecated clock code
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Soren Brinkmann [Mon, 13 May 2013 17:46:38 +0000 (10:46 -0700)]
arm: zynq: Migrate platform to clock controller
Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Soren Brinkmann [Mon, 13 May 2013 17:46:37 +0000 (10:46 -0700)]
clk: zynq: Add clock controller driver
Add a clock controller driver and documentation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Linus Torvalds [Sun, 26 May 2013 23:00:47 +0000 (16:00 -0700)]
Linux 3.10-rc3
Manfred Spraul [Sun, 26 May 2013 09:08:52 +0000 (11:08 +0200)]
ipc/sem.c: Fix missing wakeups in do_smart_update_queue()
do_smart_update_queue() is called when an operation (semop,
semctl(SETVAL), semctl(SETALL), ...) modified the array. It must check
which of the sleeping tasks can proceed.
do_smart_update_queue() missed a few wakeups:
- if a sleeping complex op was completed, then all per-semaphore queues
must be scanned - not only those that were modified by *sops
- if a sleeping simple op proceeded, then the global queue must be
scanned again
And:
- the test for "|sops == NULL) before scanning the global queue is not
required: If the global queue is empty, then it doesn't need to be
scanned - regardless of the reason for calling do_smart_update_queue()
The patch is not optimized, i.e. even completing a wait-for-zero
operation causes a rescan. This is done to keep the patch as simple as
possible.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 26 May 2013 19:33:05 +0000 (12:33 -0700)]
Merge tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix to prevent an rpc_task wakeup race
- Fix a NFSv4.1 session drain deadlock
- Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
- Ensure auth_gss pipe detection works in namespaces
- Fix SETCLIENTID fallback if rpcsec_gss is not available
* tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix SETCLIENTID fallback if GSS is not available
SUNRPC: Prevent an rpc_task wakeup race
NFSv4.1 Fix a pNFS session draining deadlock
SUNRPC: Convert auth_gss pipe detection to work in namespaces
SUNRPC: Faster detection if gssd is actually running
SUNRPC: Fix a bug in gss_create_upcall
Andrew Lunn [Sun, 27 Jan 2013 10:07:24 +0000 (11:07 +0100)]
arm: kirkwood: Enable cpufreq and ondemand on kirkwood_defconfig
Now that we have a cpufreq driver for kirkwood, enable it in
kirkwood_defconfig and set the default governer to ondemand.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Linus Torvalds [Sun, 26 May 2013 16:52:26 +0000 (09:52 -0700)]
Merge tag 'edac_fixes_for_3.10' of git://git./linux/kernel/git/bp/bp
Pull amd64 edac fix from Borislav Petkov:
"A sysfs file permissions correction"
* tag 'edac_fixes_for_3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Fix bogus sysfs file permissions
Linus Torvalds [Sun, 26 May 2013 16:36:31 +0000 (09:36 -0700)]
Merge branch 'parisc-for-3.10' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This time we made the kernel- and interruption stack allocation
reentrant which fixed some strange kernel crashes (specifically
protection ID traps).
Furthemore this patchset fixes the interrupt stack in UP and SMP
configurations by using native locking instructions. And finally
usage of floating point calculations on parisc were disabled in the
MPILIB."
* 'parisc-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix irq stack on UP and SMP
parisc/superio: Use module_pci_driver to register driver
parisc: make interrupt and interruption stack allocation reentrant
parisc: show number of FPE and unaligned access handler calls in /proc/interrupts
parisc: add additional parisc git tree to MAINTAINERS file
parisc: use PAGE_SHIFT instead of hardcoded value 12 in pacache.S
parisc: add rp5470 entry to machine database
MPILIB: disable usage of floating point registers on parisc
Linus Torvalds [Sun, 26 May 2013 16:35:02 +0000 (09:35 -0700)]
Merge tag 'for-linus-v3.10-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs fixes from Ben Myers:
"Here are fixes for corruption on 512 byte filesystems, a rounding
error, a use-after-free, some flags to fix lockdep reports, and
several fixes related to CRCs. We have a somewhat larger post -rc1
queue than usual due to fixes related to the CRC feature we merged for
3.10:
- Fix for corruption with FSX on 512 byte blocksize filesystems
- Fix rounding error in xfs_free_file_space
- Fix use-after-free with extent free intents
- Add several missing KM_NOFS flags to fix lockdep reports
- Several fixes for CRC related code"
* tag 'for-linus-v3.10-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: remote attribute lookups require the value length
xfs: xfs_attr_shortform_allfit() does not handle attr3 format.
xfs: xfs_da3_node_read_verify() doesn't handle XFS_ATTR3_LEAF_MAGIC
xfs: fix missing KM_NOFS tags to keep lockdep happy
xfs: Don't reference the EFI after it is freed
xfs: fix rounding in xfs_free_file_space
xfs: fix sub-page blocksize data integrity writes
Linus Torvalds [Sun, 26 May 2013 03:32:49 +0000 (20:32 -0700)]
Merge tag 'for-v3.10-fixes' of git://git.infradead.org/battery-2.6
Pull bettery fixes from Anton Vorontsov:
"Last minute one-liners: wrong kfree usage fix, module alias fixup and
kconfig adjustments"
* tag 'for-v3.10-fixes' of git://git.infradead.org/battery-2.6:
pm2301_charger: Fix module alias prefix
wm831x_backup: Fix wrong kfree call for devdata->backup.name
bq27x00: Fix I2C dependency in KConfig
lp8788-charger: Fix kconfig dependency
Linus Torvalds [Sun, 26 May 2013 03:32:00 +0000 (20:32 -0700)]
Merge tag 'pm+acpi-3.10-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
- Additional CPU ID for the intel_pstate driver from Dirk Brandewie.
- More cpufreq fixes related to ARM big.LITTLE support and locking from
Viresh Kumar.
- VIA C7 cpufreq build fix from Rafał Bilski.
- ACPI power management fix making it possible to use device power
states regardless of the CONFIG_PM setting from Rafael J Wysocki.
- New ACPI video blacklist item from Bastian Triller.
* tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
cpufreq: arm_big_little_dt: Instantiate as platform_driver
cpufreq: arm_big_little_dt: Register driver only if DT has valid data
cpufreq / e_powersaver: Fix linker error when ACPI processor is a module
cpufreq / intel_pstate: Add additional supported CPU ID
cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT
ACPI / PM: Allow device power states to be used for CONFIG_PM unset
Linus Torvalds [Sun, 26 May 2013 03:30:31 +0000 (20:30 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dma fixes from Vinod Koul:
"We have two patches from Andy & Rafael fixing the Lynxpoint dma"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
ACPI / LPSS: register clock device for Lynxpoint DMA properly
dma: acpi-dma: parse CSRT to extract additional resources
Kyle McMartin [Sat, 25 May 2013 16:54:08 +0000 (12:54 -0400)]
score: remove redundant kcore_list entries
kcore_vmalloc is in fs/proc/kcore.c and kcore_mem is unused across
the tree. Noticed while grepping the tree for some other kcore stuff.
(score looks pretty unmaintained to me.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 25 May 2013 17:06:20 +0000 (10:06 -0700)]
Merge tag 'arc-v3.10-fixes' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fallouts/wreckage of Cache Flush optimizations / aliasing dcache
support
- Fix for an interesting bug where piped input to grep was getting
mysteriously clobbered
* tag 'arc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: lazy dcache flush broke gdb in non-aliasing configs
ARC: Use enough bits for determining page's cache color
ARC: Brown paper bag bug in macro for checking cache color
ARC: copy_(to|from)_user() to honor usermode-access permissions
ARC: [mm] Prevent stray dcache lines after__sync_icache_dcach()
ARC: [TB10x] Remove redundant abilis,simple-pinctrl mechanism
Linus Torvalds [Sat, 25 May 2013 17:05:24 +0000 (10:05 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Just three this time, all really quite small"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supported
ARM: 7727/1: remove the .vm_mm value from gate_vma
ARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handling
Vineet Gupta [Sat, 25 May 2013 08:34:25 +0000 (14:04 +0530)]
ARC: lazy dcache flush broke gdb in non-aliasing configs
gdbserver inserting a breakpoint ends up calling copy_user_page() for a
code page. The generic version of which (non-aliasing config) didn't set
the PG_arch_1 bit hence update_mmu_cache() didn't sync dcache/icache for
corresponding dynamic loader code page - causing garbade to be executed.
So now aliasing versions of copy_user_highpage()/clear_page() are made
default. There is no significant overhead since all of special alias
handling code is compiled out for non-aliasing build
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Sat, 25 May 2013 01:12:15 +0000 (18:12 -0700)]
Merge branch 'akpm' (incoming from Andrew Morton)
Merge fixes from Andrew Morton:
"A bunch of fixes and one simple fbdev driver which missed the merge
window because people will still talking about it (to no great
effect)."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (30 commits)
aio: fix kioctx not being freed after cancellation at exit time
mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
random: fix accounting race condition with lockless irq entropy_count update
drivers/char/random.c: fix priming of last_data
mm/memory_hotplug.c: fix printk format warnings
nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
drivers/block/brd.c: fix brd_lookup_page() race
fbdev: FB_GOLDFISH should depend on HAS_DMA
drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
auditfilter.c: fix kernel-doc warnings
aio: fix io_getevents documentation
revert "selftest: add simple test for soft-dirty bit"
drivers/leds/leds-ot200.c: fix error caused by shifted mask
mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
linux/kernel.h: fix kernel-doc warning
mm compaction: fix of improper cache flush in migration code
rapidio/tsi721: fix bug in MSI interrupt handling
hfs: avoid crash in hfs_bnode_create
...
Linus Torvalds [Fri, 24 May 2013 23:27:37 +0000 (16:27 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have any fixes sent up for -rc2, so this is a slightly
larger batch. A bit all over the place platform-wise; OMAP, at91,
marvell, renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig
updates due to new/changing options."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: at91/sama5: fix incorrect PMC pcr div definition
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
ARM: at91: at91sam9n12: move external irq declatation to DT
ARM: shmobile: marzen: Use error values in usb_power_*
ARM: tegra: defconfig fixes
ARM: nomadik: fix IRQ assignment for SMC ethernet
ARM: vt8500: Add missing NULL terminator in dt_compat
clk: tegra: add ac97 controller clock
clk: tegra: remove USB from clk init table
ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
ARM: plat-orion: Fix num_resources and id for ge10 and ge11
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
arm: mvebu: fix the 'ranges' property to handle PCIe
ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
...
Benjamin LaHaise [Fri, 24 May 2013 22:55:38 +0000 (15:55 -0700)]
aio: fix kioctx not being freed after cancellation at exit time
The recent changes overhauling fs/aio.c introduced a bug that results in
the kioctx not being freed when outstanding kiocbs are cancelled at
exit_aio() time. Specifically, a kiocb that is cancelled has its
completion events discarded by batch_complete_aio(), which then fails to
wake up the process stuck in free_ioctx(). Fix this by modifying the
wait_event() condition in free_ioctx() appropriately.
This patch was tested with the cancel operation in the thread based code
posted yesterday.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Zach Brown <zab@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cliff Wickman [Fri, 24 May 2013 22:55:36 +0000 (15:55 -0700)]
mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
A panic can be caused by simply cat'ing /proc/<pid>/smaps while an
application has a VM_PFNMAP range. It happened in-house when a
benchmarker was trying to decipher the memory layout of his program.
/proc/<pid>/smaps and similar walks through a user page table should not
be looking at VM_PFNMAP areas.
Certain tests in walk_page_range() (specifically split_huge_page_pmd())
assume that all the mapped PFN's are backed with page structures. And
this is not usually true for VM_PFNMAP areas. This can result in panics
on kernel page faults when attempting to address those page structures.
There are a half dozen callers of walk_page_range() that walk through a
task's entire page table (as N. Horiguchi pointed out). So rather than
change all of them, this patch changes just walk_page_range() to ignore
VM_PFNMAP areas.
The logic of hugetlb_vma() is moved back into walk_page_range(), as we
want to test any vma in the range.
VM_PFNMAP areas are used by:
- graphics memory manager gpu/drm/drm_gem.c
- global reference unit sgi-gru/grufile.c
- sgi special memory char/mspec.c
- and probably several out-of-tree modules
[akpm@linux-foundation.org: remove now-unused hugetlb_vma() stub]
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Sterba <dsterba@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tomasz Figa [Fri, 24 May 2013 22:55:35 +0000 (15:55 -0700)]
drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
Currently the driver can crash with a NULL pointer dereference if no
pdata is provided, despite of successful registration of the MFD part.
This patch fixes the problem by adding a NULL check before dereferencing
the pdata pointer.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Fri, 24 May 2013 22:55:34 +0000 (15:55 -0700)]
ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
Last time we found there is lock/unlock bug in ocfs2_file_aio_write, and
then we did a thorough search for all lock resources in
ocfs2_inode_info, including rw, inode and open lockres and found this
bug. My kernel version is 3.0.13, and it is also in the lastest version
3.9. In ocfs2_fiemap, once ocfs2_get_clusters_nocache failed, it should
goto out_unlock instead of out, because we need release buffer head, up
read alloc sem and unlock inode.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Kosina [Fri, 24 May 2013 22:55:33 +0000 (15:55 -0700)]
random: fix accounting race condition with lockless irq entropy_count update
Commit
902c098a3663 ("random: use lockless techniques in the interrupt
path") turned IRQ path from being spinlock protected into lockless
cmpxchg-retry update.
That commit removed r->lock serialization between crediting entropy bits
from IRQ context and accounting when extracting entropy on userspace
read path, but didn't turn the r->entropy_count reads/updates in
account() to use cmpxchg as well.
It has been observed, that under certain circumstances this leads to
read() on /dev/urandom to return 0 (EOF), as r->entropy_count gets
corrupted and becomes negative, which in turn results in propagating 0
all the way from account() to the actual read() call.
Convert the accounting code to be the proper lockless counterpart of
what has been partially done by
902c098a3663.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jarod Wilson [Fri, 24 May 2013 22:55:31 +0000 (15:55 -0700)]
drivers/char/random.c: fix priming of last_data
Commit
ec8f02da9ea5 ("random: prime last_data value per fips
requirements") added priming of last_data per fips requirements.
Unfortuantely, it did so in a way that can lead to multiple threads all
incrementing nbytes, but only one actually doing anything with the extra
data, which leads to some fun random corruption and panics.
The fix is to simply do everything needed to prime last_data in a single
shot, so there's no window for multiple cpus to increment nbytes -- in
fact, we won't even increment or decrement nbytes anymore, we'll just
extract the needed EXTRACT_SIZE one time per pool and then carry on with
the normal routine.
All these changes have been tested across multiple hosts and
architectures where panics were previously encoutered. The code changes
are are strictly limited to areas only touched when when booted in fips
mode.
This change should also go into 3.8-stable, to make the myriads of fips
users on 3.8.x happy.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stodola <jstodola@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 24 May 2013 22:55:30 +0000 (15:55 -0700)]
mm/memory_hotplug.c: fix printk format warnings
Fix printk format warnings in mm/memory_hotplug.c by using "%pa":
mm/memory_hotplug.c: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 2 has type 'resource_size_t' [-Wformat]
mm/memory_hotplug.c: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'resource_size_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryusuke Konishi [Fri, 24 May 2013 22:55:29 +0000 (15:55 -0700)]
nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
nilfs2: fix issue of nilfs_set_page_dirty for page at EOF boundary
DESCRIPTION:
There are use-cases when NILFS2 file system (formatted with block size
lesser than 4 KB) can be remounted in RO mode because of encountering of
"broken bmap" issue.
The issue was reported by Anthony Doggett <Anthony2486@interfaces.org.uk>:
"The machine I've been trialling nilfs on is running Debian Testing,
Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc
version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.35-2), but I've
also reproduced it (identically) with Debian Unstable amd64 and Debian
Experimental (using the 3.8-trunk kernel). The problematic partitions
were formatted with "mkfs.nilfs2 -b 1024 -B 8192"."
SYMPTOMS:
(1) System log contains error messages likewise:
[63102.496756] nilfs_direct_assign: invalid pointer: 0
[63102.496786] NILFS error (device dm-17): nilfs_bmap_assign: broken bmap (inode number=28)
[63102.496798]
[63102.524403] Remounting filesystem read-only
(2) The NILFS2 file system is remounted in RO mode.
REPRODUSING PATH:
(1) Create volume group with name "unencrypted" by means of vgcreate utility.
(2) Run script (prepared by Anthony Doggett <Anthony2486@interfaces.org.uk>):
----------------[BEGIN SCRIPT]--------------------
VG=unencrypted
lvcreate --size 2G --name ntest $VG
mkfs.nilfs2 -b 1024 -B 8192 /dev/mapper/$VG-ntest
mkdir /var/tmp/n
mkdir /var/tmp/n/ntest
mount /dev/mapper/$VG-ntest /var/tmp/n/ntest
mkdir /var/tmp/n/ntest/thedir
cd /var/tmp/n/ntest/thedir
sleep 2
date
darcs init
sleep 2
dmesg|tail -n 5
date
darcs whatsnew || true
date
sleep 2
dmesg|tail -n 5
----------------[END SCRIPT]--------------------
REPRODUCIBILITY: 100%
INVESTIGATION:
As it was discovered, the issue takes place during segment
construction after executing such sequence of user-space operations:
open("_darcs/index", O_RDWR|O_CREAT|O_NOCTTY, 0666) = 7
fstat(7, {st_mode=S_IFREG|0644, st_size=0, ...}) = 0
ftruncate(7, 60)
The error message "NILFS error (device dm-17): nilfs_bmap_assign: broken
bmap (inode number=28)" takes place because of trying to get block
number for third block of the file with logical offset #3072 bytes. As
it is possible to see from above output, the file has 60 bytes of the
whole size. So, it is enough one block (1 KB in size) allocation for
the whole file. Trying to operate with several blocks instead of one
takes place because of discovering several dirty buffers for this file
in nilfs_segctor_scan_file() method.
The root cause of this issue is in nilfs_set_page_dirty function which
is called just before writing to an mmapped page.
When nilfs_page_mkwrite function handles a page at EOF boundary, it
fills hole blocks only inside EOF through __block_page_mkwrite().
The __block_page_mkwrite() function calls set_page_dirty() after filling
hole blocks, thus nilfs_set_page_dirty function (=
a_ops->set_page_dirty) is called. However, the current implementation
of nilfs_set_page_dirty() wrongly marks all buffers dirty even for page
at EOF boundary.
As a result, buffers outside EOF are inconsistently marked dirty and
queued for write even though they are not mapped with nilfs_get_block
function.
FIX:
This modifies nilfs_set_page_dirty() not to mark hole blocks dirty.
Thanks to Vyacheslav Dubeyko for his effort on analysis and proposals
for this issue.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Reported-by: Anthony Doggett <Anthony2486@interfaces.org.uk>
Reported-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Brian Behlendorf [Fri, 24 May 2013 22:55:28 +0000 (15:55 -0700)]
drivers/block/brd.c: fix brd_lookup_page() race
The index on the page must be set before it is inserted in the radix
tree. Otherwise there is a small race which can occur during lookup
where the page can be found with the incorrect index. This will trigger
the BUG_ON() in brd_lookup_page().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Chris Wedgwood <cw@f00f.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Fri, 24 May 2013 22:55:27 +0000 (15:55 -0700)]
fbdev: FB_GOLDFISH should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `goldfish_fb_remove':
drivers/video/goldfishfb.c:301: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `goldfish_fb_probe':
drivers/video/goldfishfb.c:247: undefined reference to `dma_alloc_coherent'
drivers/video/goldfishfb.c:280: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lars-Peter Clausen [Fri, 24 May 2013 22:55:26 +0000 (15:55 -0700)]
drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
free_irq() expects the same pointer that was passed to request_irq(),
otherwise the IRQ is not freed.
The issue was found using the following coccinelle script:
<smpl>
@r1@
type T;
T devid;
@@
request_irq(..., devid)
@r2@
type r1.T;
T devid;
position p;
@@
free_irq@p(..., devid)
@@
position p != r2.p;
@@
*free_irq@p(...)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 24 May 2013 22:55:25 +0000 (15:55 -0700)]
auditfilter.c: fix kernel-doc warnings
Fix kernel-doc warnings in kernel/auditfilter.c:
Warning(kernel/auditfilter.c:1029): Excess function parameter 'loginuid' description in 'audit_receive_filter'
Warning(kernel/auditfilter.c:1029): Excess function parameter 'sessionid' description in 'audit_receive_filter'
Warning(kernel/auditfilter.c:1029): Excess function parameter 'sid' description in 'audit_receive_filter'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Moyer [Fri, 24 May 2013 22:55:24 +0000 (15:55 -0700)]
aio: fix io_getevents documentation
In reviewing man pages, I noticed that io_getevents is documented to
update the timeout that gets passed into the library call. This doesn't
happen in kernel space or in the library (even though it's documented to
do so in both places). Unless there is objection, I'd like to fix the
comments/docs to match the code (I will also update the man page upon
consensus).
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Cyril Hrubis <chrubis@suse.cz>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Fri, 24 May 2013 22:55:23 +0000 (15:55 -0700)]
revert "selftest: add simple test for soft-dirty bit"
Revert commit
58c7be84fec8 ("selftest: add simple test for soft-dirty
bit"). This is the self test for Pavel's pagemap2 patches which didn't
actually get merged.
Reported-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian Gmeiner [Fri, 24 May 2013 22:55:22 +0000 (15:55 -0700)]
drivers/leds/leds-ot200.c: fix error caused by shifted mask
During the development of this driver an in-house register documentation
was used. The last week some integration tests were done and this
problem was found. It turned out that the released register
documentation is wrong.
The fix is very simple: shift all masks by one.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aneesh Kumar K.V [Fri, 24 May 2013 22:55:21 +0000 (15:55 -0700)]
mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
We should not use set_pmd_at to update pmd_t with pgtable_t pointer.
set_pmd_at is used to set pmd with huge pte entries and architectures
like ppc64, clear few flags from the pte when saving a new entry.
Without this change we observe bad pte errors like below on ppc64 with
THP enabled.
BUG: Bad page map in process ld mm=0xc000001ee39f4780 pte:
7fc3f37848000001 pmd:
c000001ec0000000
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 24 May 2013 22:55:20 +0000 (15:55 -0700)]
linux/kernel.h: fix kernel-doc warning
Fix kernel-doc warning in <linux/kernel.h>:
Warning(include/linux/kernel.h:590): No description found for parameter 'ip'
scripts/kernel-doc cannot handle macros, functions, or function
prototypes between the function or macro that is being documented and
its definition, so move these prototypes above the function that is
being documented.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leonid Yegoshin [Fri, 24 May 2013 22:55:18 +0000 (15:55 -0700)]
mm compaction: fix of improper cache flush in migration code
Page 'new' during MIGRATION can't be flushed with flush_cache_page().
Using flush_cache_page(vma, addr, pfn) is justified only if the page is
already placed in process page table, and that is done right after
flush_cache_page(). But without it the arch function has no knowledge
of process PTE and does nothing.
Besides that, flush_cache_page() flushes an application cache page, but
the kernel has a different page virtual address and dirtied it.
Replace it with flush_dcache_page(new) which is the proper usage.
The old page is flushed in try_to_unmap_one() before migration.
This bug takes place in Sead3 board with M14Kc MIPS CPU without cache
aliasing (but Harvard arch - separate I and D cache) in tight memory
environment (128MB) each 1-3days on SOAK test. It fails in cc1 during
kernel build (SIGILL, SIGBUS, SIGSEG) if CONFIG_COMPACTION is switched
ON.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Leonid Yegoshin <yegoshin@mips.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Fri, 24 May 2013 22:55:17 +0000 (15:55 -0700)]
rapidio/tsi721: fix bug in MSI interrupt handling
Fix bug in MSI interrupt handling which causes loss of event
notifications.
Typical indication of lost MSI interrupts are stalled message and
doorbell transfers between RapidIO endpoints. To avoid loss of MSI
interrupts all interrupts from the device must be disabled on entering
the interrupt handler routine and re-enabled when exiting it.
Re-enabling device interrupts will trigger new MSI message(s) if Tsi721
registered new events since entering interrupt handler routine.
This patch is applicable to kernel versions starting from v3.2.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Mahoney [Fri, 24 May 2013 22:55:16 +0000 (15:55 -0700)]
hfs: avoid crash in hfs_bnode_create
Commit
634725a92938 ("hfs: cleanup HFS+ prints") removed the BUG_ON in
hfs_bnode_create in hfsplus. This patch removes it from the hfs version
and avoids an fsfuzzer crash.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 24 May 2013 22:55:15 +0000 (15:55 -0700)]
mm: memcg: remove incorrect VM_BUG_ON for swap cache pages in uncharge
Commit
0c59b89c81ea ("mm: memcg: push down PageSwapCache check into
uncharge entry functions") added a VM_BUG_ON() on PageSwapCache in the
uncharge path after checking that page flag once, assuming that the
state is stable in all paths, but this is not the case and the condition
triggers in user environments. An uncharge after the last page table
reference to the page goes away can race with reclaim adding the page to
swap cache.
Swap cache pages are usually uncharged when they are freed after
swapout, from a path that also handles swap usage accounting and memcg
lifetime management. However, since the last page table reference is
gone and thus no references to the swap slot left, the swap slot will be
freed shortly when reclaim attempts to write the page to disk. The
whole swap accounting is not even necessary.
So while the race condition for which this VM_BUG_ON was added is real
and actually existed all along, there are no negative effects. Remove
the VM_BUG_ON again.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Warren [Fri, 24 May 2013 22:55:13 +0000 (15:55 -0700)]
drivers/video: implement a simple framebuffer driver
A simple frame-buffer describes a raw memory region that may be rendered
to, with the assumption that the display hardware has already been set
up to scan out from that buffer.
This is useful in cases where a bootloader exists and has set up the
display hardware, but a Linux driver doesn't yet exist for the display
hardware.
Examples use-cases include:
* The built-in LCD panels on the Samsung ARM chromebook, and Tegra
devices, and likely many other ARM or embedded systems. These cannot
yet be supported using a full graphics driver, since the panel control
should be provided by the CDF (Common Display Framework), which has been
stuck in design/review for quite some time. One could support these
panels using custom SoC-specific code, but there is a desire to use
common infra-structure rather than having each SoC vendor invent their
own code, hence the desire to wait for CDF.
* Hardware for which a full graphics driver is not yet available, and
the path to obtain one upstream isn't yet clear. For example, the
Raspberry Pi.
* Any hardware in early stages of upstreaming, before a full graphics
driver has been tackled. This driver can provide a graphical boot
console (even full X support) much earlier in the upstreaming process,
thus making new SoC or board support more generally useful earlier.
[akpm@linux-foundation.org: make simplefb_formats[] static]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Rob Clark <robclark@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Fri, 24 May 2013 22:55:12 +0000 (15:55 -0700)]
ocfs2: unlock rw lock if inode lock failed
In ocfs2_file_aio_write(), it does ocfs2_rw_lock() first and then
ocfs2_inode_lock().
But if ocfs2_inode_lock() failed, it goes to out_sems without unlocking
rw lock. This will cause a bug in ocfs2_lock_res_free() when testing
res->l_ex_holders, which is increased in __ocfs2_cluster_lock() and
decreased in __ocfs2_cluster_unlock().
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: "Duyongfeng (B)" <du.duyongfeng@huawei.com>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xiao Guangrong [Fri, 24 May 2013 22:55:11 +0000 (15:55 -0700)]
mm: mmu_notifier: re-fix freed page still mapped in secondary MMU
Commit
751efd8610d3 ("mmu_notifier_unregister NULL Pointer deref and
multiple ->release()") breaks the fix
3ad3d901bbcf ("mm: mmu_notifier:
fix freed page still mapped in secondary MMU").
Since hlist_for_each_entry_rcu() is changed now, we can not revert that
patch directly, so this patch reverts the commit and simply fix the bug
spotted by that patch
This bug spotted by commit
751efd8610d3 is:
There is a race condition between mmu_notifier_unregister() and
__mmu_notifier_release().
Assume two tasks, one calling mmu_notifier_unregister() as a result
of a filp_close() ->flush() callout (task A), and the other calling
mmu_notifier_release() from an mmput() (task B).
A B
t1 srcu_read_lock()
t2 if (!hlist_unhashed())
t3 srcu_read_unlock()
t4 srcu_read_lock()
t5 hlist_del_init_rcu()
t6 synchronize_srcu()
t7 srcu_read_unlock()
t8 hlist_del_rcu() <--- NULL pointer deref.
This can be fixed by using hlist_del_init_rcu instead of hlist_del_rcu.
The another issue spotted in the commit is "multiple ->release()
callouts", we needn't care it too much because it is really rare (e.g,
can not happen on kvm since mmu-notify is unregistered after
exit_mmap()) and the later call of multiple ->release should be fast
since all the pages have already been released by the first call.
Anyway, this issue should be fixed in a separate patch.
-stable suggestions: Any version that has commit
751efd8610d3 need to be
backported. I find the oldest version has this commit is 3.0-stable.
[akpm@linux-foundation.org: tweak comments]
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Tested-by: Robin Holt <holt@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Fri, 24 May 2013 22:55:09 +0000 (15:55 -0700)]
wait: fix false timeouts when using wait_event_timeout()
Many callers of the wait_event_timeout() and
wait_event_interruptible_timeout() expect that the return value will be
positive if the specified condition becomes true before the timeout
elapses. However, at the moment this isn't guaranteed. If the wake-up
handler is delayed enough, the time remaining until timeout will be
calculated as 0 - and passed back as a return value - even if the
condition became true before the timeout has passed.
Fix this by returning at least 1 if the condition becomes true. This
semantic is in line with what wait_for_condition_timeout() does; see
commit
bb10ed09 ("sched: fix wait_for_completion_timeout() spurious
failure under heavy load").
Daniel said "We have 3 instances of this bug in drm/i915. One case even
where we switch between the interruptible and not interruptible
wait_event_timeout variants, foolishly presuming they have the same
semantics. I very much like this."
One such bug is reported at
https://bugs.freedesktop.org/show_bug.cgi?id=64133
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Fri, 24 May 2013 22:55:08 +0000 (15:55 -0700)]
fat: fix possible overflow for fat_clusters
Intermediate value of fat_clusters can be overflowed on 32bits arch.
Reported-by: Krzysztof Strasburger <strasbur@chkw386.ch.pwr.wroc.pl>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Fri, 24 May 2013 22:55:07 +0000 (15:55 -0700)]
rapidio: documentation update for enumeration changes
Update RapidIO documentation to reflect changes made to
enumeration/discovery build configuration and user space triggering
mechanism.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Fri, 24 May 2013 22:55:06 +0000 (15:55 -0700)]
rapidio: add enumeration/discovery start from user space
Add RapidIO enumeration/discovery start from user space. User space
start allows to defer RapidIO fabric scan until the moment when all
participating endpoints are initialized avoiding mandatory synchronized
start of all endpoints (which may be challenging in systems with large
number of RapidIO endpoints).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Fri, 24 May 2013 22:55:05 +0000 (15:55 -0700)]
rapidio: make enumeration/discovery configurable
Systems that use RapidIO fabric may need to implement their own
enumeration and discovery methods which are better suitable for needs of
a target application.
The following set of patches is intended to simplify process of
introduction of new RapidIO fabric enumeration/discovery methods.
The first patch offers ability to add new RapidIO enumeration/discovery
methods using kernel configuration options. This new configuration
option mechanism allows to select statically linked or modular
enumeration/discovery method(s) from the list of existing methods or use
external module(s).
This patch also updates the currently existing enumeration/discovery
code to be used as a statically linked or modular method.
The corresponding configuration option is named "Basic
enumeration/discovery" method. This is the only one configuration
option available today but new methods are expected to be introduced
after adoption of provided patches.
The second patch address a long time complaint of RapidIO subsystem
users regarding fabric enumeration/discovery start sequence. Existing
implementation offers only a boot-time enumeration/discovery start which
requires synchronized boot of all endpoints in RapidIO network. While
it works for small closed configurations with limited number of
endpoints, using this approach in systems with large number of endpoints
is quite challenging.
To eliminate requirement for synchronized start the second patch
introduces RapidIO enumeration/discovery start from user space.
For compatibility with the existing RapidIO subsystem implementation,
automatic boot time enumeration/discovery start can be configured in by
specifying "rio-scan.scan=1" command line parameter if statically linked
basic enumeration method is selected.
This patch:
Rework to implement RapidIO enumeration/discovery method selection
combined with ability to use enumeration/discovery as a kernel module.
This patch adds ability to introduce new RapidIO enumeration/discovery
methods using kernel configuration options. Configuration option
mechanism allows to select statically linked or modular
enumeration/discovery method from the list of existing methods or use
external modules. If a modular enumeration/discovery is selected each
RapidIO mport device can have its own method attached to it.
The existing enumeration/discovery code was updated to be used as
statically linked or modular method. This configuration option is named
"Basic enumeration/discovery" method.
Several common routines have been moved from rio-scan.c to make them
available to other enumeration methods and reduce number of exported
symbols.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gernot Vormayr [Fri, 24 May 2013 22:55:03 +0000 (15:55 -0700)]
drivers/block/xsysace.c: fix id with missing port-number
If the port number is missing from the device-tree the device gets named
xs` instead of xsa. This fixes the check for missing ids.
Tested on ml507 board.
Signed-off-by: Gernot Vormayr <gvormayr@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Fri, 24 May 2013 20:17:49 +0000 (13:17 -0700)]
Merge tag 'sunxi-fixes-for-3.10' of git://github.com/mripard/linux into fixes
From Maxime Ripard:
Small set of fixes for 3.10:
- Fix build breakage in pinctrl driver when no other architecture is selected
- Fix Mini X-plus device tree build
* tag 'sunxi-fixes-for-3.10' of git://github.com/mripard/linux:
ARM: sunxi: select ARCH_REQUIRE_GPIOLIB
ARM: sunxi: Fix Mini X-plus device tree build
Signed-off-by: Olof Johansson <olof@lixom.net>
Dave Chinner [Sun, 19 May 2013 23:51:16 +0000 (09:51 +1000)]
xfs: remote attribute lookups require the value length
When reading a remote attribute, to correctly calculate the length
of the data buffer for CRC enable filesystems, we need to know the
length of the attribute data. We get this information when we look
up the attribute, but we don't store it in the args structure along
with the other remote attr information we get from the lookup. Add
this information to the args structure so we can use it
appropriately.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit
e461fcb194172b3f709e0b478d2ac1bdac7ab9a3)
Dave Chinner [Sun, 19 May 2013 23:51:14 +0000 (09:51 +1000)]
xfs: xfs_attr_shortform_allfit() does not handle attr3 format.
xfstests generic/117 fails with:
XFS: Assertion failed: leaf->hdr.info.magic == cpu_to_be16(XFS_ATTR_LEAF_MAGIC)
indicating a function that does not handle the attr3 format
correctly. Fix it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit
b38958d715316031fe9ea0cc6c22043072a55f49)
Dave Chinner [Sun, 19 May 2013 23:51:13 +0000 (09:51 +1000)]
xfs: xfs_da3_node_read_verify() doesn't handle XFS_ATTR3_LEAF_MAGIC
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit
72916fb8cbcf0c2928f56cdc2fbe8c7bf5517758)
Dave Chinner [Sun, 19 May 2013 23:51:12 +0000 (09:51 +1000)]
xfs: fix missing KM_NOFS tags to keep lockdep happy
There are several places where we use KM_SLEEP allocation contexts
and use the fact that they are called from transaction context to
add KM_NOFS where appropriate. Unfortunately, there are several
places where the code makes this assumption but can be called from
outside transaction context but with filesystem locks held. These
places need explicit KM_NOFS annotations to avoid lockdep
complaining about reclaim contexts.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit
ac14876cf9255175bf3bdad645bf8aa2b8fb2d7c)
Helge Deller [Fri, 24 May 2013 21:27:35 +0000 (21:27 +0000)]
parisc: fix irq stack on UP and SMP
The logic to detect if the irq stack was already in use with
raw_spin_trylock() is wrong, because it will generate a "trylock failure
on UP" error message with CONFIG_SMP=n and CONFIG_DEBUG_SPINLOCK=y.
arch_spin_trylock() can't be used either since in the CONFIG_SMP=n case
no atomic protection is given and we are reentrant here. A mutex didn't
worked either and brings more overhead by turning off interrupts.
So, let's use the fastest path for parisc which is the ldcw instruction.
Counting how often the irq stack was used is pretty useless, so just
drop this piece of code.
Signed-off-by: Helge Deller <deller@gmx.de>
Dave Chinner [Sun, 19 May 2013 23:51:10 +0000 (09:51 +1000)]
xfs: Don't reference the EFI after it is freed
Checking the EFI for whether it is being released from recovery
after we've already released the known active reference is a mistake
worthy of a brown paper bag. Fix the (now) obvious use after free
that it can cause.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit
52c24ad39ff02d7bd73c92eb0c926fb44984a41d)
Dave Chinner [Sun, 19 May 2013 23:51:09 +0000 (09:51 +1000)]
xfs: fix rounding in xfs_free_file_space
The offset passed into xfs_free_file_space() needs to be rounded
down to a certain size, but the rounding mask is built by a 32 bit
variable. Hence the mask will always mask off the upper 32 bits of
the offset and lead to incorrect writeback and invalidation ranges.
This is not actually exposed as a bug because we writeback and
invalidate from the rounded offset to the end of the file, and hence
the offset we are actually punching a hole out of will always be
covered by the code. This needs fixing, however, if we ever want to
use exact ranges for writeback/invalidation here...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit
28ca489c63e9aceed8801d2f82d731b3c9aa50f5)