OSDN Git Service
Yan-Hsuan Chuang [Thu, 13 Apr 2017 18:06:54 +0000 (13:06 -0500)]
rtlwifi: btcoex: 21a 2ant: monitor wifi counter to check network status
If there are a lot of low-rate packets, then the connection of wifi is
unstable. If so, we should switch resource to bt to have a higher
transmission quality, or wifi resource will be wasted
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 13 Apr 2017 18:06:53 +0000 (13:06 -0500)]
rtlwifi: btcoex: 21a 2ant: monitor if bt is slave or not
We monitor the packet counter to guess if the bt is slave or not, and
when bt is slave, it may receive packet at any time, so we will have to
take care about it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 13 Apr 2017 18:06:52 +0000 (13:06 -0500)]
rtlwifi: btcoex: 21a 2ant: limit rx aggregation size to avoid bt interrupt
Larger packets have higher opportunity to be interrupt by bt signal.
In order to shorten the transmission time, control the packet
aggregation size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Wed, 19 Apr 2017 17:12:35 +0000 (10:12 -0700)]
MAINTAINERS: update Amitkumar's email address
His email is bouncing, and he'd like to use this new one.
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Fri, 14 Apr 2017 21:51:20 +0000 (14:51 -0700)]
mwifiex: don't leak 'chan_stats' on reset
'chan_stats' is (re)allocated in _mwifiex_fw_dpc() ->
mwifiex_init_channel_scan_gap(), which is called whenever the device is
initialized -- at probe or at reset.
But we only free it in we completely unregister the adapter, meaning we
leak a copy of it during every reset.
Let's free it in the shutdown / removal paths instead (and in the
error-handling path), to avoid the leak.
Ideally, we can eventually unify much of mwifiex_shutdown_sw() and
mwifiex_remove_card() (way too much copy-and-paste) to reduce the burden
on bugfixes like this. But that's work for tomorrow.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Fri, 14 Apr 2017 21:51:19 +0000 (14:51 -0700)]
mwifiex: pcie: clear outstanding work when resetting
When we shut down the device (i.e., during 'reset'), we cancel any
outstanding work, but we don't clear any work-related flags. This can
cause problems if, e.g., we begin to queue a new firmware dump or card
reset while the other one is in progress. That might leave work_flags
with a stale value, and we might begin one of these *after* we've
completely reset the device. That doesn't make sense, because all
firmware context will have been lost by then.
This fixes some forms of cascading failures, where I:
(a) force a firmware dump (cat /sys/kernel/debug/mwifiex/mlan0/device_dump)
(b) run a Wifi scan in parallel (iw mlan0 scan)
(c) the scan times out due to (a) hogging the interface
(d) the command timeout triggers another firmware dump and a reset [*]
(e) the 2nd firmware dump flag persists across the reset
(f) as soon as the interface comes back up, we trigger the pending
firmware dump
(g) subsequent commands time out again, while we are processing the
firmware dump; return to (d)
[*] Note that automatic card_reset() support is not yet implemented for
the mwifiex PCIe driver, so we won't hit *exactly* this behavior yet.
But we can see similarly-confusing behaviors today.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Fri, 14 Apr 2017 21:51:18 +0000 (14:51 -0700)]
mwifiex: reset timeout flag when resetting device
If we reset because of a command timeout, we should reset this flag.
Otherwise, we might erroneously think the next command after reset is
timing out, and trigger another reset.
The above behavior effectively neuters the automatic card_reset()
behavior, as it means we will never recover from a command timeout
properly (and in fact, we might enter an infinite loop:
timeout -> reset -> (fake) timeout -> reset -> ...
This fixes a bug introduced with introduction of PCIe function level
reset support, but it was carried into the SDIO driver when it was
converted to use the same codepaths. And this is currently mostly a
problem only in the SDIO driver, because it's the only one with
automatic card_reset() support (e.g., on command timeout). But it will
be a problem for PCIe too, as I'm working on supporting automatic
card_reset() for PCIe.
Fixes:
c742e623e941 ("mwifiex: sdio card reset enhancement")
Fixes:
4c5dae59d2e9 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Fri, 14 Apr 2017 21:51:17 +0000 (14:51 -0700)]
mwifiex: pcie: fix cmd_buf use-after-free in remove/reset
Command buffers (skb's) are allocated by the main driver, and freed upon
the last use. That last use is often in mwifiex_free_cmd_buffer(). In
the meantime, if the command buffer gets used by the PCI driver, we map
it as DMA-able, and store the mapping information in the 'cb' memory.
However, if a command was in-flight when resetting the device (and
therefore was still mapped), we don't get a chance to unmap this memory
until after the core has cleaned up its command handling.
Let's keep a refcount within the PCI driver, so we ensure the memory
only gets freed after we've finished unmapping it.
Noticed by KASAN when forcing a reset via:
echo 1 > /sys/bus/pci/.../reset
The same code path can presumably be exercised in remove() and
shutdown().
[ 205.390377] mwifiex_pcie 0000:01:00.0: info: shutdown mwifiex...
[ 205.400393] ==================================================================
[ 205.407719] BUG: KASAN: use-after-free in mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] at addr
ffffffc0ad471b28
[ 205.419040] Read of size 16 by task bash/1913
[ 205.423421] =============================================================================
[ 205.431625] BUG skbuff_head_cache (Tainted: G B ): kasan: bad access detected
[ 205.439815] -----------------------------------------------------------------------------
[ 205.439815]
[ 205.449534] INFO: Allocated in __build_skb+0x48/0x114 age=1311 cpu=4 pid=1913
[ 205.456709] alloc_debug_processing+0x124/0x178
[ 205.461282] ___slab_alloc.constprop.58+0x528/0x608
[ 205.466196] __slab_alloc.isra.54.constprop.57+0x44/0x54
[ 205.471542] kmem_cache_alloc+0xcc/0x278
[ 205.475497] __build_skb+0x48/0x114
[ 205.479019] __netdev_alloc_skb+0xe0/0x170
[ 205.483244] mwifiex_alloc_cmd_buffer+0x68/0xdc [mwifiex]
[ 205.488759] mwifiex_init_fw+0x40/0x6cc [mwifiex]
[ 205.493584] _mwifiex_fw_dpc+0x158/0x520 [mwifiex]
[ 205.498491] mwifiex_reinit_sw+0x2c4/0x398 [mwifiex]
[ 205.503510] mwifiex_pcie_reset_notify+0x114/0x15c [mwifiex_pcie]
[ 205.509643] pci_reset_notify+0x5c/0x6c
[ 205.513519] pci_reset_function+0x6c/0x7c
[ 205.517567] reset_store+0x68/0x98
[ 205.521003] dev_attr_store+0x54/0x60
[ 205.524705] sysfs_kf_write+0x9c/0xb0
[ 205.528413] INFO: Freed in __kfree_skb+0xb0/0xbc age=131 cpu=4 pid=1913
[ 205.535064] free_debug_processing+0x264/0x370
[ 205.539550] __slab_free+0x84/0x40c
[ 205.543075] kmem_cache_free+0x1c8/0x2a0
[ 205.547030] __kfree_skb+0xb0/0xbc
[ 205.550465] consume_skb+0x164/0x178
[ 205.554079] __dev_kfree_skb_any+0x58/0x64
[ 205.558304] mwifiex_free_cmd_buffer+0xa0/0x158 [mwifiex]
[ 205.563817] mwifiex_shutdown_drv+0x578/0x5c4 [mwifiex]
[ 205.569164] mwifiex_shutdown_sw+0x178/0x310 [mwifiex]
[ 205.574353] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.580398] pci_reset_notify+0x5c/0x6c
[ 205.584274] pci_dev_save_and_disable+0x24/0x6c
[ 205.588837] pci_reset_function+0x30/0x7c
[ 205.592885] reset_store+0x68/0x98
[ 205.596324] dev_attr_store+0x54/0x60
[ 205.600017] sysfs_kf_write+0x9c/0xb0
...
[ 205.800488] Call trace:
[ 205.802980] [<
ffffffc00020a69c>] dump_backtrace+0x0/0x190
[ 205.808415] [<
ffffffc00020a96c>] show_stack+0x20/0x28
[ 205.813506] [<
ffffffc0005d020c>] dump_stack+0xa4/0xcc
[ 205.818598] [<
ffffffc0003be44c>] print_trailer+0x158/0x168
[ 205.824120] [<
ffffffc0003be5f0>] object_err+0x4c/0x5c
[ 205.829210] [<
ffffffc0003c45bc>] kasan_report+0x334/0x500
[ 205.834641] [<
ffffffc0003c3994>] check_memory_region+0x20/0x14c
[ 205.840593] [<
ffffffc0003c3b14>] __asan_loadN+0x14/0x1c
[ 205.845879] [<
ffffffbffc46171c>] mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie]
[ 205.854282] [<
ffffffbffc461864>] mwifiex_pcie_delete_cmdrsp_buf+0x94/0xa8 [mwifiex_pcie]
[ 205.862421] [<
ffffffbffc462028>] mwifiex_pcie_free_buffers+0x11c/0x158 [mwifiex_pcie]
[ 205.870302] [<
ffffffbffc4620d4>] mwifiex_pcie_down_dev+0x70/0x80 [mwifiex_pcie]
[ 205.877736] [<
ffffffbffc1397a8>] mwifiex_shutdown_sw+0x190/0x310 [mwifiex]
[ 205.884658] [<
ffffffbffc4606b4>] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.892446] [<
ffffffc000635f54>] pci_reset_notify+0x5c/0x6c
[ 205.898048] [<
ffffffc00063a044>] pci_dev_save_and_disable+0x24/0x6c
[ 205.904350] [<
ffffffc00063cf0c>] pci_reset_function+0x30/0x7c
[ 205.910134] [<
ffffffc000641118>] reset_store+0x68/0x98
[ 205.915312] [<
ffffffc000771588>] dev_attr_store+0x54/0x60
[ 205.920750] [<
ffffffc00046f53c>] sysfs_kf_write+0x9c/0xb0
[ 205.926182] [<
ffffffc00046dfb0>] kernfs_fop_write+0x184/0x1f8
[ 205.931963] [<
ffffffc0003d64f4>] __vfs_write+0x6c/0x17c
[ 205.937221] [<
ffffffc0003d7164>] vfs_write+0xf0/0x1c4
[ 205.942310] [<
ffffffc0003d7da0>] SyS_write+0x78/0xd8
[ 205.947312] [<
ffffffc000204634>] el0_svc_naked+0x24/0x28
...
[ 205.998268] ==================================================================
This bug has been around in different forms for a while. It was sort of
noticed in commit
955ab095c51a ("mwifiex: Do not kfree cmd buf while
unregistering PCIe"), but it just fixed the double-free, without
acknowledging the potential for use-after-free.
Fixes:
fc3314609047 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Thu, 13 Apr 2017 20:10:33 +0000 (13:10 -0700)]
mwifiex: pcie: extract wifi part from combo firmware during function level reset
A separate wifi-only firmware was download during pcie function level
reset. It is in fact the tail part of wifi/bt combo firmware. Per
Brian's and Dmitry's suggestion, this patch extract the wifi part from
combo firmware.
After that, the mrvl/pcie8997_wlan_v4.bin image in linux-firmware repo
is redundant (though I guess we keep it around to support older
kernels).
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Thu, 13 Apr 2017 06:48:21 +0000 (06:48 +0000)]
mwifiex: pcie: correct scratch register name
This patch correct pcie scratch register name, to keep the same with
chipset side definition.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Thu, 13 Apr 2017 06:48:20 +0000 (06:48 +0000)]
mwifiex: fall back mwifiex_dbg to pr_info when adapter->dev not set
mwifiex_dbg will do nothing before adapter->dev get assigned. several logs
lost in this case. it can be avoided by fall back to pr_info.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Thu, 13 Apr 2017 06:48:19 +0000 (06:48 +0000)]
mwifiex: remove unnecessary wakeup interrupt number sanity check
If wakeup interrupt handler is called, we know that the wakeup
interrupt number is valid, there is no need to check it.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Wed, 5 Apr 2017 22:26:40 +0000 (15:26 -0700)]
mwifiex: MAC randomization should not be persistent
nl80211 provides the NL80211_SCAN_FLAG_RANDOM_ADDR for every scan
request that should be randomized; the absence of such a flag means we
should not randomize. However, mwifiex was stashing the latest
randomization request and *always* using it for future scans, even those
that didn't set the flag.
Let's zero out the randomization info whenever we get a scan request
without NL80211_SCAN_FLAG_RANDOM_ADDR. I'd prefer to remove
priv->random_mac entirely (and plumb the randomization MAC properly
through the call sequence), but the spaghetti is a little difficult to
unravel here for me.
Fixes:
c2a8f0ff9c6c ("mwifiex: support random MAC address for scanning")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Fri, 14 Apr 2017 21:27:37 +0000 (22:27 +0100)]
brcmfmac: only build fwsignal module for CONFIG_BRCMFMAC_PROTO_BCDC
The fwsignal module is only referenced by the bcdc module and part of the
bcdc protocol. So only build it when CONFIG_BRCMFMAC_PROTO_BCDC is selected.
Fixes:
acf8ac41dd73 ("brcmfmac: remove reference to fwsignal data from struct brcmf_pub")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Tue, 18 Apr 2017 06:41:45 +0000 (09:41 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2017-04-13' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
Patches intended for v4.12:
* Some small fixes here and there;
* The usual cleanups and small improvements;
* Work to support A000 devices continues;
* New FW API version;
* Some debugging improvements;
Daniel Golle [Mon, 10 Apr 2017 13:29:45 +0000 (15:29 +0200)]
rt2x00: reverse external PA capability flag logic
Consequently refer to external PA instead of inverting the logic and
use an internal PA capability flag which is a bit confusing.
Currently this is used for Rt3352 only, but MT7620A also allows for an
external PA which will be supported by a follow up patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:10 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: avoid LPS/IPS mismatch for pnp notify
When driver is going to sleep, it does not leave LPS/IPS, thus the
BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex
needs to clear the IPS/LPS state when it receives a pnp notify, then
it can properly set up the hw when driver wakes up.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:09 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: do not switch antenna when wifi is under 5G channel
When wifi is on a 5G channel, the 5G signal will not interfere bt 2.4G
signal, and they can transmit simultaneously, hence there is no need to
switch antenna between wifi and bt.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:08 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: monitor bt profiling when scan
When wifi is scanning and not connected, set the tdma and coex table
properly to control the priority of the packets to make the wifi bt
coexistence operate smoothly
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:07 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: consider more cases when bt inquiry
With bt inquiry, the wifi may start as a softap or the wifi and bt are
busy, we take these scenarios into consider to avoid bt inquiry to
degrade the performance of the network
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:06 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: move bt_disabled to global struct
Move the bt disable flag to a global structure to indicate that bt is
turned off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:05 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: If wifi only, do not initiate coex mechanism
If the device has wifi mode only, there is no need to initiate the
hardware for wifi and bt coexistence, so just return to avoid it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:04 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: action when associating/authenticating
When wifi is associating or authenticating, set the coex table for wifi
to establish link. These packets should have higher priority.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:03 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: add multi port action for miracast and P2P
To support miracast and P2P, the chip may operate under concurrent mode,
In this situation, do not aggregate tx packet and properly set the rx
aggregation size.
We detect it by monitoring the number of link established.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:02 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: set antenna control path for PTA
Set antenna control path if PTA is in control of the packet path of wifi
and bt. If wifi is turned off, tell the PTA about it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:01 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: remove setting for 2 antennas
The antenna position setting is useless for 1 antenna chip.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:23:00 +0000 (11:23 -0500)]
rtlwifi: btcoex: 21a 1ant: mask profile bit for connect-ilde
Mask out the connect-idle bit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:22:59 +0000 (11:22 -0500)]
rtlwifi: btcoex: 21a 1ant: coex table setting for new fw
For newer fw, the coex table setting needs to be modified to operate
correctly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:22:58 +0000 (11:22 -0500)]
rtlwifi: btcoex: 21a 1ant: add function to check wifi status
This function checks if wifi has changed its statusi. It will be needed
in the future.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Mon, 10 Apr 2017 16:22:57 +0000 (11:22 -0500)]
rtlwifi: btcoex: 21a 1ant: fw settings for softap mode
For ap mode, adjust fw settings to operate properly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:58 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: some hi-prio pkt will cause hid_exist
Clear the hid_exist flag by monitoring the packet counter.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:57 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: notify more bt information
These bt information are displayed in display coex
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:56 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: fine tune for bt hid_a2dp
Let bt control the aggregation size to improve stability.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:55 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: fine tune for bt pan_edr_a2dp
If we don't limit the rx aggregation size, and set tdma instead, the bt profile can
get more stable.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:54 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: before firmware ready settings
Before firmware is ready, set GNT_BT to high to let bt transmit
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:53 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: power on settings for coex
When power on, the wifi could be initiating, force the antenna to
transmit bt packets to avoid bt unstable problems
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:52 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: wifi is not actually off in mp mode
In mp mode, the wifi will not turn off and still has control of the PTA,
so the driver needs to distinguish whether it is mp mode or not
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:51 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: need those information when scan
For scan notify, we need to supervise some registers to make sure that
coexistence is operating as we expected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:50 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: remove debugging code for 0x948
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:49 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: treat too many low prio packets as retry
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Thu, 6 Apr 2017 20:19:48 +0000 (15:19 -0500)]
rtlwifi: btcoex: 23b 2ant: set coex table when wifi is idle
When wifi is idle, the bt should have more resource to transmit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:50:06 +0000 (11:50 -0500)]
rtlwifi: btcoex: 23b 2ant: set coex table when wifi is linking
When wifi is under linking process, those packets are important. Mark
them as high priority to protect the linking process
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:50:05 +0000 (11:50 -0500)]
rtlwifi: btcoex: 23b 2ant: turn off antenna when rssi is too high/low
For 2-antenna combo card, the signal of the neighbor antenna could be
over noise level and cause be severe interference. So we monitor the
rssi and turn off one of the antennas when the other is transmitting
and the rssi level is beyond a threshold.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:50:04 +0000 (11:50 -0500)]
rtlwifi: btcoex: 23b 2ant: turn off ps and tdma mechanism when in concurrent mode
When wifi is in concurrent mode, we can not distinguish if it is the
real PS or just a fake one by sending null data, so we turn it off
in case of miracast scenario.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:50:03 +0000 (11:50 -0500)]
rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done
During hw initialisation, wifi may be ready after bt has already been
ready, which causes bt to act abnormally. To avoid this, set GNT_BT to
high during hw init.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Stable <stable@vger.kernel.org>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:50:02 +0000 (11:50 -0500)]
rtlwifi: btcoex: 23b 2ant: tell fw if external or internal switch is used
Some chips use an external antenna switch, but fw may not realize it.
Here we tell fw exactly that which type of switch we are using.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:50:01 +0000 (11:50 -0500)]
rtlwifi: btcoex: 23b 2ant: workaround for bt a2dp and hid
For a2dp and hid, we need extra process to avoid voice degradation
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:50:00 +0000 (11:50 -0500)]
rtlwifi: btcoex: 23b 2ant: check more cases when bt is queuing
If bt is queing, we need to set the packet priority properly.
Originally we only consider if wifi was connected or not, but now we
also consider if bt is under abnormal scan or wifi is scanning, roaming
or linking, and set the coex table.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:49:59 +0000 (11:49 -0500)]
rtlwifi: btcoex: 23b 2ant: add pnp notidy to avoid LPS/IPS mismatch
When driver is going to sleep, it does not leave LPS/IPS, thus the
BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex
needs to clear the IPS/LPS state when it receives a pnp notify, then
it can properly set up the hw when driver wakes up.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:49:58 +0000 (11:49 -0500)]
rtlwifi: btcoex: 23b 2ant: fix PTA unstable problem when hw init
In the hardware initialisation stage, the PTA circuits may be unstable,
so we reset it after 6 secs to fix the problem.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:49:57 +0000 (11:49 -0500)]
rtlwifi: btcoex: 23b 2ant: more cases for adjusting tdma duration
These cases are for the btcoex to tune the performance
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:49:56 +0000 (11:49 -0500)]
rtlwifi: btcoex: 23b 2ant: detect ap num and set GNT_BT properly
If ap num < 10, let wifi and bt transmit simultaneously, otherwise set
wifi into standy when bt is transmitting
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:49:55 +0000 (11:49 -0500)]
rtlwifi: btcoex: 23b 2ant: rename tdma_adj_type to ps_tdma_du_adj_type
The variable is for PS tdma duration adjust, so rename it to clearly
to specify its usage.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yan-Hsuan Chuang [Tue, 4 Apr 2017 16:49:54 +0000 (11:49 -0500)]
rtlwifi: btcoex: 23b 2ant: check PS state before setting tdma duration
For time division multiple access, the wifi and bt take turns to
transmit, but we need to let AP know that wifi is under standby mode by
sending null data to "pretend" entering power saving state using lps
rpwm.
But, the fw does not know if it is the actual power saving mode or just a
fake one to cheat to the AP. Hence, before fw setting the tdma duration,
the fw needs the driver to check the power saving state first.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Thu, 6 Apr 2017 12:14:42 +0000 (13:14 +0100)]
brcmfmac: only add channels and ssids once in scan request
When receiving pno results there may be duplicate channels and/or
ssids. Assure each is added only once when preparing the internal
escan request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Thu, 6 Apr 2017 12:14:41 +0000 (13:14 +0100)]
brcmfmac: remove bogus check in scheduled scan result handler
Checking whether the address of an array element is null is bogus
so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Thu, 6 Apr 2017 12:14:40 +0000 (13:14 +0100)]
brcmfmac: add length checks in scheduled scan result handler
Assure the event data buffer is long enough to hold the array
of netinfo items and that SSID length does not exceed the maximum
of 32 characters as per 802.11 spec.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Thu, 6 Apr 2017 12:14:39 +0000 (13:14 +0100)]
brcmfmac: remove reference to fwsignal data from struct brcmf_pub
The fwsignal module is part of the bcdc protocol and as such does
its instance data is not needed in core structure. Moving it into
struct brcmf_bcdc instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Thu, 6 Apr 2017 12:14:38 +0000 (13:14 +0100)]
brcmfmac: ignore interfaces when fwsignal is disabled
When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc
field is initialized regardless the state of the fwsignal functionality,
ie. the fcmode. This is not needed when fcmode is NONE, which is the
default mode.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Thu, 6 Apr 2017 12:14:37 +0000 (13:14 +0100)]
brcmfmac: rename brcmf_fws_{de,}init to brcmf_fws{at,de}tach
This is a non-functional change to align the fwsignal module to
the naming pattern used throughout the driver.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Heiner Kallweit [Wed, 5 Apr 2017 18:33:26 +0000 (20:33 +0200)]
brcmfmac: properly align buffers on certain platforms with 64 bit DMA
Systems with 64 bit DMA at least partially require buffers to be used
for DMA to be 8-byte-aligned. One example is Amlogic Meson GX.
Switching the MMC/SDIO driver for this platform to SG DMA mode
resulted in problems due to unaligned buffers.
Fortunately the brcmfmac driver has a global define for the alignment.
Changing it to 8 fixed the issues with Meson GX.
Suggested-by: Helmut Klein <hgkr.klein@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ganapathi Bhat [Tue, 4 Apr 2017 04:46:28 +0000 (10:16 +0530)]
mwifiex: Fix invalid port issue
We have to use start port, for TX/RX of single packet,
instead of current aggregating port. This will fix SDIO
CMD53(TX/RX) returning -ETIMEDOUT and halting the data path.
Fixes:
0cb52aac4d19 ("mwifiex: do not set multiport flag for tx/rx single packet")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Alexey Dobriyan [Mon, 10 Apr 2017 08:25:26 +0000 (11:25 +0300)]
net: make struct net_device::min_header_len 8-bit
This field is never big enough to warrant 16-bitness.
8-bit accesses enjoy shorted encoding on i386/x86_64 than 16-bit
accesses:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10)
function old new delta
loopback_setup 169 164 -5
ether_setup 148 143 -5
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Mon, 10 Apr 2017 08:11:17 +0000 (11:11 +0300)]
net: neigh: make ->hh_len 32-bit
Using 16-bit ->hh_len doesn't save any memory, save some .text instead:
add/remove: 0/0 grow/shrink: 1/6 up/down: 2/-19 (-17)
function old new delta
neigh_update 2312 2314 +2
fwnet_header_cache 199 197 -2
eth_header_cache 101 99 -2
ip6_finish_output2 2371 2368 -3
vrf_finish_output6 1522 1518 -4
vrf_finish_output 1413 1409 -4
ip_finish_output2 1627 1623 -4
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilan Tayari [Fri, 7 Apr 2017 23:07:08 +0000 (02:07 +0300)]
gso: Support frag_list splitting with head_frag
A driver may use build_skb() for received packets.
These SKBs then have a head_frag.
Since commit
d7e8883cfcf4 ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.
Commit
07b26c9454a2 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.
A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.
This causes low performance when forwarding those packets
that were built with build_skb()
Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.
Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Apr 2017 14:44:03 +0000 (10:44 -0400)]
Merge branch 'l2tp-const'
Guillaume Nault says:
====================
l2tp: constify l2tp_session_get*() and l2tp_tunnel_find*()
Declare parameters of these functions as "const" where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Wed, 12 Apr 2017 08:05:30 +0000 (10:05 +0200)]
l2tp: define parameters of l2tp_tunnel_find*() as "const"
l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net".
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Wed, 12 Apr 2017 08:05:29 +0000 (10:05 +0200)]
l2tp: define parameters of l2tp_session_get*() as "const"
Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Apr 2017 14:17:03 +0000 (10:17 -0400)]
Merge branch 'ftgmac100-rework-batch4-misc'
Benjamin Herrenschmidt says:
====================
ftgmac100: Rework batch 4 - Misc
This is v2 of the fourth batch of updates to the ftgmac100 driver.
This is a bunch of misc cleanups and fixes, such as properly
disabling HW checksum generation on AST2400 where it's known
to be broken and some chip init updates.
This also adds the ability to turn HW checksum on/off and
configure the ring sizes via ethtool.
v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion)
The next (and last) batch will add a few more "features" such
as netpoll, multicast/promist, vlan offload...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:10 +0000 (13:27 +1000)]
ftgmac100: Set default ring sizes to 128 entries
I haven't seen any improvement above that size on the machines
I've tested with.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:09 +0000 (13:27 +1000)]
ftgmac100: Make ring sizes configurable via ethtool
We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:08 +0000 (13:27 +1000)]
ftgmac100: Add more register inits in ftgmac100_init_hw()
Clear stale interrupts on entry, configure FIFO sizes, set FIFO
thresholds, configure interrupt mitigation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:07 +0000 (13:27 +1000)]
ftgmac100: Open code remaining register writes
The helpers just take space but don't provide much value. Simple
one line comments are more explanatory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:06 +0000 (13:27 +1000)]
ftgmac100: Rename ftgmac100_setup_mac to ftgmac100_initial_mac
To remove more confusion. This function is about obtaining the
initial MAC address at driver probe time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:05 +0000 (13:27 +1000)]
ftgmac100: Rename ftgmac100_set_mac to ftgmac100_write_mac_addr
To avoid confusion with the ndo callback and generally be
clearer about the purpose of that function
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:04 +0000 (13:27 +1000)]
ftgmac100: Set netdev->hw_features
So features can be turned on/off via ethtool
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:03 +0000 (13:27 +1000)]
ftgmac100: Disable HW checksum generation on AST2400, enable on others
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:02 +0000 (13:27 +1000)]
ftgmac100: Use device "compatible" property, not machine.
We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.
Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Wed, 12 Apr 2017 03:27:01 +0000 (13:27 +1000)]
ftgmac100: Upgrade to NETIF_F_HW_CSUM
The documentation describes NETIF_F_IP_CSUM as deprecated
so let's switch to NETIF_F_HW_CSUM and use the helper to
handle unhandled protocols.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Apr 2017 03:01:15 +0000 (23:01 -0400)]
Merge branch 'net-smc-next'
Ursula Braun says:
====================
net/smc: patches for net-next
here are some patches for net/smc. Most important are
improvements for socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:05 +0000 (14:58 +0200)]
net/smc: do not use IB_SEND_INLINE together with mapped data
smc specifies IB_SEND_INLINE for IB_WR_SEND ib_post_send calls, but
provides a mapped buffer to be sent. This is inconsistent, since
IB_SEND_INLINE works without mapped buffer. Problem has not been
detected in the past, because tests had been limited to Connect X3 cards
from Mellanox, whose mlx4 driver just ignored the IB_SEND_INLINE flag.
For now, the IB_SEND_INLINE flag is removed.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:04 +0000 (14:58 +0200)]
net/smc: destruct non-accepted sockets
Make sure sockets never accepted are removed cleanly.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:03 +0000 (14:58 +0200)]
net/smc: remove duplicate unhash
unhash is already called in sock_put_work. Remove the second call.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:02 +0000 (14:58 +0200)]
net/smc: guarantee ConnClosed send after shutdown SHUT_WR
State SMC_CLOSED should be reached only, if ConnClosed has been sent to
the peer. If ConnClosed is received from the peer, a socket with
shutdown SHUT_WR done, switches errorneously to state SMC_CLOSED, which
means the peer socket is dangling. The local SMC socket is supposed to
switch to state APPFINCLOSEWAIT to make sure smc_close_final() is called
during socket close.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:01 +0000 (14:58 +0200)]
net/smc: no socket state changes in tasklet context
Several state changes occur during SMC socket closing. Currently
state changes triggered locally occur in process context with
lock_sock() taken while state changes triggered by peer occur in
tasklet context with bh_lock_sock() taken. bh_lock_sock() does not
wait till a lock_sock(() task in process context is finished. This
may lead to races in socket state transitions resulting in dangling
SMC-sockets, or it may lead to duplicate SMC socket freeing.
This patch introduces a closing worker to run all state changes under
lock_sock().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:58:00 +0000 (14:58 +0200)]
net/smc: always call the POLL_IN part of sk_wake_async
Wake up reading file descriptors for a closing socket as well, otherwise
some socket applications may stall.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:59 +0000 (14:57 +0200)]
net/smc: guarantee reset of write_blocked for heavy workload
If peer indicates write_blocked, the cursor state of the received data
should be send to the peer immediately (in smc_tx_consumer_update()).
Afterwards the write_blocked indicator is cleared.
If there is no free slot for another write request, sending is postponed
to worker smc_tx_work, and the write_blocked indicator is not cleared.
Therefore another clearing check is needed in smc_tx_work().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:58 +0000 (14:57 +0200)]
net/smc: return active RoCE port only
SMC requires an active ib port on the RoCE device.
smc_pnet_find_roce_resource() determines the matching RoCE device port
according to the configured PNET table. Do not return the found
RoCE device port, if it is not flagged active.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:57 +0000 (14:57 +0200)]
net/smc: remove useless smc_ib_devices_list check
The global event handler is created only, if the ib_device has already
been used by at least one link group. It is guaranteed that there exists
the corresponding entry in the smc_ib_devices list. Get rid of this
superfluous check.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 10 Apr 2017 12:57:56 +0000 (14:57 +0200)]
net/smc: get rid of old comment
This patch removes an outdated comment.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joao Pinto [Mon, 10 Apr 2017 10:32:14 +0000 (11:32 +0100)]
net: stmmac: use netif_set_real_num_{rx,tx}_queues
In the submission of the lastest multiple buffer patch set, this fix was lost.
I am sending this patch to put it right again. The fix was originally proposed
by Arnd Bergmann.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Tue, 11 Apr 2017 18:08:08 +0000 (14:08 -0400)]
bpf: pass sk to helper functions
BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.
Temporarily set skb->sk to sk in these cases.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 11 Apr 2017 16:02:02 +0000 (16:02 +0000)]
devlink: fix return value check in devlink_dpipe_header_put()
Fix the return value check which testing the wrong variable
in devlink_dpipe_header_put().
Fixes:
1555d204e743 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 11 Apr 2017 18:51:36 +0000 (14:51 -0400)]
Merge branch 's390-qeth-updates'
Julian Wiedmann says:
====================
more s390/net updates
here's a second batch of s390/net patches for net-next.
A mixed bunch of qeth cleanups, and a few patches to add support for
ETHTOOL_GLINKSETTINGS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:19 +0000 (16:11 +0200)]
s390/qeth: remove unimplemented gdev routines
prepare() and complete() are not implemented by any discipline, so just
drop all the indirection.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:18 +0000 (16:11 +0200)]
s390/qeth: use LINK_MODE_* to report the link characteristics
LINK_MODE_* replaces the u32-limited SUPPORTED_* / ENABLED_*
definitions.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:17 +0000 (16:11 +0200)]
s390/qeth: convert to ETHTOOL_GLINKSETTINGS API
get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:16 +0000 (16:11 +0200)]
s390/qeth: clean up qeth_set_ecmd_adv_sup()
In preparation for moving to get_link_ksettings(), clean up how
we build the supported and advertised port/speed masks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:15 +0000 (16:11 +0200)]
s390/qeth: use and remove some defines
1. a buffer has 16 is_header flags, because that's its # of elements
2. replace the last occurrence of QETH_HEADER_SIZE, and remove it
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 11 Apr 2017 14:11:14 +0000 (16:11 +0200)]
s390/qeth: use correct return type for hard_start_xmit()
ndo_start_xmit() expects us to return netdev_tx_t here...
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>