OSDN Git Service
Christian Lamparter [Thu, 29 Dec 2016 14:12:09 +0000 (16:12 +0200)]
ath10k: fix potential memory leak in ath10k_wmi_tlv_op_pull_fw_stats()
[ Upstream commit
097e46d2ae90265d1afe141ba6208ba598b79e01 ]
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ryan Hsu [Thu, 22 Dec 2016 23:02:37 +0000 (15:02 -0800)]
ath10k: ignore configuring the incorrect board_id
[ Upstream commit
d2e202c06ca42d353d95df12437740921a6d05b5 ]
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ryan Hsu [Tue, 13 Dec 2016 22:55:19 +0000 (14:55 -0800)]
ath10k: fix incorrect txpower set by P2P_DEVICE interface
[ Upstream commit
88407beb1b1462f706a1950a355fd086e1c450b6 ]
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Fri, 30 Dec 2016 16:38:52 +0000 (17:38 +0100)]
drm/armada: Fix compile fail
[ Upstream commit
7357f89954b6d005df6ab8929759e78d7d9a80f9 ]
I reported the include issue for tracepoints a while ago, but nothing
seems to have happened. Now it bit us, since the drm_mm_print
conversion was broken for armada. Fix it, so I can re-enable armada
in the drm-misc build configs.
v2: Rebase just the compile fix on top of Chris' build fix.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483115932-19584-1-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Preisner [Fri, 30 Dec 2016 02:37:53 +0000 (03:37 +0100)]
net: 3com: typhoon: typhoon_init_one: fix incorrect return values
[ Upstream commit
107fded7bf616ad6f46823d98b8ed6405d7adf2d ]
In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188841
Reported-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Preisner [Fri, 30 Dec 2016 02:37:54 +0000 (03:37 +0100)]
net: 3com: typhoon: typhoon_init_one: make return values more specific
[ Upstream commit
6b6bbb5922a4b1d4b58125a572da91010295fba3 ]
In some cases the return value of a failing function is not being used
and the function typhoon_init_one() returns another negative error code
instead.
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Ahern [Thu, 29 Dec 2016 23:39:37 +0000 (15:39 -0800)]
net: Allow IP_MULTICAST_IF to set index to L3 slave
[ Upstream commit
7bb387c5ab12aeac3d5eea28686489ff46b53ca9 ]
IP_MULTICAST_IF fails if sk_bound_dev_if is already set and the new index
does not match it. e.g.,
ntpd[15381]: setsockopt IP_MULTICAST_IF 192.168.1.23 fails: Invalid argument
Relax the check in setsockopt to allow setting mc_index to an L3 slave if
sk_bound_dev_if points to an L3 master.
Make a similar change for IPv6. In this case change the device lookup to
take the rcu_read_lock avoiding a refcnt. The rcu lock is also needed for
the lookup of a potential L3 master device.
This really only silences a setsockopt failure since uses of mc_index are
secondary to sk_bound_dev_if if it is set. In both cases, if either index
is an L3 slave or master, lookups are directed to the same FIB table so
relaxing the check at setsockopt time causes no harm.
Patch is based on a suggested change by Darwin for a problem noted in
their code base.
Suggested-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shawn Guo [Thu, 15 Dec 2016 14:03:36 +0000 (22:03 +0800)]
dmaengine: zx: set DMA_CYCLIC cap_mask bit
[ Upstream commit
fc318d64f3d91e15babac00e08354b1beb650b57 ]
The zx_dma driver supports cyclic transfer mode. Let's set DMA_CYCLIC
cap_mask bit to make that clear, and avoid unnecessary failure when
clients request channel via dma_request_chan_by_mask() with DMA_CYCLIC
bit set in mask.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn Helgaas [Mon, 2 Jan 2017 20:04:24 +0000 (14:04 -0600)]
PCI: Apply _HPX settings only to relevant devices
[ Upstream commit
977509f7c5c6fb992ffcdf4291051af343b91645 ]
Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.
We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.
We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings. I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's
ugly to depend on those internals.
Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).
A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:
pci 0000:00:00.0: PCI-X settings not supported
After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Santosh Shilimkar [Tue, 5 Jul 2016 00:04:37 +0000 (17:04 -0700)]
RDS: RDMA: return appropriate error on rdma map failures
[ Upstream commit
584a8279a44a800dea5a5c1e9d53a002e03016b4 ]
The first message to a remote node should prompt a new
connection even if it is RDMA operation. For RDMA operation
the MR mapping can fail because connections is not yet up.
Since the connection establishment is asynchronous,
we make sure the map failure because of unavailable
connection reach to the user by appropriate error code.
Before returning to the user, lets trigger the connection
so that its ready for the next retry.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Poirier [Fri, 21 Jul 2017 18:36:26 +0000 (11:36 -0700)]
e1000e: Separate signaling for link check/link up
commit
19110cfbb34d4af0cdfe14cd243f3b09dc95b013 upstream.
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Poirier [Fri, 21 Jul 2017 18:36:25 +0000 (11:36 -0700)]
e1000e: Fix return value test
commit
d3509f8bc7b0560044c15f0e3ecfde1d9af757a6 upstream.
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Poirier [Fri, 21 Jul 2017 18:36:23 +0000 (11:36 -0700)]
e1000e: Fix error path in link detection
commit
c4c40e51f9c32c6dd8adf606624c930a1c4d9bbb upstream.
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tobias Jordan [Wed, 4 Oct 2017 06:05:03 +0000 (11:35 +0530)]
PM / OPP: Add missing of_node_put(np)
commit
7978db344719dab1e56d05e6fc04aaaddcde0a5e upstream.
The for_each_available_child_of_node() loop in _of_add_opp_table_v2()
doesn't drop the reference to "np" on errors. Fix that.
Fixes:
274659029c9d (PM / OPP: Add support to parse "operating-points-v2" bindings)
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
[ VK: Improved commit log. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuomas Tynkkynen [Wed, 6 Sep 2017 14:59:08 +0000 (17:59 +0300)]
net/9p: Switch to wait_event_killable()
commit
9523feac272ccad2ad8186ba4fcc89103754de52 upstream.
Because userspace gets Very Unhappy when calls like stat() and execve()
return -EINTR on 9p filesystem mounts. For instance, when bash is
looking in PATH for things to execute and some SIGCHLD interrupts
stat(), bash can throw a spurious 'command not found' since it doesn't
retry the stat().
In practice, hitting the problem is rare and needs a really
slow/bogged down 9p server.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Sun, 29 Oct 2017 10:30:19 +0000 (06:30 -0400)]
fscrypt: lock mutex before checking for bounce page pool
commit
a0b3bc855374c50b5ea85273553485af48caf2f7 upstream.
fscrypt_initialize(), which allocates the global bounce page pool when
an encrypted file is first accessed, uses "double-checked locking" to
try to avoid locking fscrypt_init_mutex. However, it doesn't use any
memory barriers, so it's theoretically possible for a thread to observe
a bounce page pool which has not been fully initialized. This is a
classic bug with "double-checked locking".
While "only a theoretical issue" in the latest kernel, in pre-4.8
kernels the pointer that was checked was not even the last to be
initialized, so it was easily possible for a crash (NULL pointer
dereference) to happen. This was changed only incidentally by the large
refactor to use fs/crypto/.
Solve both problems in a trivial way that can easily be backported: just
always take the mutex. It's theoretically less efficient, but it
shouldn't be noticeable in practice as the mutex is only acquired very
briefly once per encrypted file.
Later I'd like to make this use a helper macro like DO_ONCE(). However,
DO_ONCE() runs in atomic context, so we'd need to add a new macro that
allows blocking.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt (Red Hat) [Fri, 6 Oct 2017 18:05:04 +0000 (14:05 -0400)]
sched/rt: Simplify the IPI based RT balancing logic
commit
4bdced5c9a2922521e325896a7bbbf0132c94e56 upstream.
When a CPU lowers its priority (schedules out a high priority task for a
lower priority one), a check is made to see if any other CPU has overloaded
RT tasks (more than one). It checks the rto_mask to determine this and if so
it will request to pull one of those tasks to itself if the non running RT
task is of higher priority than the new priority of the next task to run on
the current CPU.
When we deal with large number of CPUs, the original pull logic suffered
from large lock contention on a single CPU run queue, which caused a huge
latency across all CPUs. This was caused by only having one CPU having
overloaded RT tasks and a bunch of other CPUs lowering their priority. To
solve this issue, commit:
b6366f048e0c ("sched/rt: Use IPI to trigger RT task push migration instead of pulling")
changed the way to request a pull. Instead of grabbing the lock of the
overloaded CPU's runqueue, it simply sent an IPI to that CPU to do the work.
Although the IPI logic worked very well in removing the large latency build
up, it still could suffer from a large number of IPIs being sent to a single
CPU. On a 80 CPU box, I measured over 200us of processing IPIs. Worse yet,
when I tested this on a 120 CPU box, with a stress test that had lots of
RT tasks scheduling on all CPUs, it actually triggered the hard lockup
detector! One CPU had so many IPIs sent to it, and due to the restart
mechanism that is triggered when the source run queue has a priority status
change, the CPU spent minutes! processing the IPIs.
Thinking about this further, I realized there's no reason for each run queue
to send its own IPI. As all CPUs with overloaded tasks must be scanned
regardless if there's one or many CPUs lowering their priority, because
there's no current way to find the CPU with the highest priority task that
can schedule to one of these CPUs, there really only needs to be one IPI
being sent around at a time.
This greatly simplifies the code!
The new approach is to have each root domain have its own irq work, as the
rto_mask is per root domain. The root domain has the following fields
attached to it:
rto_push_work - the irq work to process each CPU set in rto_mask
rto_lock - the lock to protect some of the other rto fields
rto_loop_start - an atomic that keeps contention down on rto_lock
the first CPU scheduling in a lower priority task
is the one to kick off the process.
rto_loop_next - an atomic that gets incremented for each CPU that
schedules in a lower priority task.
rto_loop - a variable protected by rto_lock that is used to
compare against rto_loop_next
rto_cpu - The cpu to send the next IPI to, also protected by
the rto_lock.
When a CPU schedules in a lower priority task and wants to make sure
overloaded CPUs know about it. It increments the rto_loop_next. Then it
atomically sets rto_loop_start with a cmpxchg. If the old value is not "0",
then it is done, as another CPU is kicking off the IPI loop. If the old
value is "0", then it will take the rto_lock to synchronize with a possible
IPI being sent around to the overloaded CPUs.
If rto_cpu is greater than or equal to nr_cpu_ids, then there's either no
IPI being sent around, or one is about to finish. Then rto_cpu is set to the
first CPU in rto_mask and an IPI is sent to that CPU. If there's no CPUs set
in rto_mask, then there's nothing to be done.
When the CPU receives the IPI, it will first try to push any RT tasks that is
queued on the CPU but can't run because a higher priority RT task is
currently running on that CPU.
Then it takes the rto_lock and looks for the next CPU in the rto_mask. If it
finds one, it simply sends an IPI to that CPU and the process continues.
If there's no more CPUs in the rto_mask, then rto_loop is compared with
rto_loop_next. If they match, everything is done and the process is over. If
they do not match, then a CPU scheduled in a lower priority task as the IPI
was being passed around, and the process needs to start again. The first CPU
in rto_mask is sent the IPI.
This change removes this duplication of work in the IPI logic, and greatly
lowers the latency caused by the IPIs. This removed the lockup happening on
the 120 CPU machine. It also simplifies the code tremendously. What else
could anyone ask for?
Thanks to Peter Zijlstra for simplifying the rto_loop_start atomic logic and
supplying me with the rto_start_trylock() and rto_start_unlock() helper
functions.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Clark Williams <williams@redhat.com>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: John Kacur <jkacur@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Scott Wood <swood@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170424114732.1aac6dc4@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ricardo Ribalda Delgado [Tue, 17 Oct 2017 15:48:50 +0000 (11:48 -0400)]
media: v4l2-ctrl: Fix flags field on Control events
commit
9cac9d2fb2fe0e0cadacdb94415b3fe49e3f724f upstream.
VIDIOC_DQEVENT and VIDIOC_QUERY_EXT_CTRL should give the same output for
the control flags field.
This patch creates a new function user_flags(), that calculates the user
exported flags value (which is different than the kernel internal flags
structure). This function is then used by all the code that exports the
internal flags to userspace.
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 21 Sep 2017 08:40:18 +0000 (05:40 -0300)]
cx231xx-cards: fix NULL-deref on missing association descriptor
commit
6c3b047fa2d2286d5e438bcb470c7b1a49f415f6 upstream.
Make sure to check that we actually have an Interface Association
Descriptor before dereferencing it during probe to avoid dereferencing a
NULL-pointer.
Fixes:
e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Young [Sun, 8 Oct 2017 18:18:52 +0000 (14:18 -0400)]
media: rc: check for integer overflow
commit
3e45067f94bbd61dec0619b1c32744eb0de480c8 upstream.
The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called
with a timeout of 4294968us.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michele Baldessari [Mon, 6 Nov 2017 13:50:22 +0000 (08:50 -0500)]
media: Don't do DMA on stack for firmware upload in the AS102 driver
commit
b3120d2cc447ee77b9d69bf4ad7b452c9adb4d39 upstream.
Firmware load on AS102 is using the stack which is not allowed any
longer. We currently fail with:
kernel: transfer buffer not dma capable
kernel: ------------[ cut here ]------------
kernel: WARNING: CPU: 0 PID: 598 at drivers/usb/core/hcd.c:1595 usb_hcd_map_urb_for_dma+0x41d/0x620
kernel: Modules linked in: amd64_edac_mod(-) edac_mce_amd as102_fe dvb_as102(+) kvm_amd kvm snd_hda_codec_realtek dvb_core snd_hda_codec_generic snd_hda_codec_hdmi snd_hda_intel snd_hda_codec irqbypass crct10dif_pclmul crc32_pclmul snd_hda_core snd_hwdep snd_seq ghash_clmulni_intel sp5100_tco fam15h_power wmi k10temp i2c_piix4 snd_seq_device snd_pcm snd_timer parport_pc parport tpm_infineon snd tpm_tis soundcore tpm_tis_core tpm shpchp acpi_cpufreq xfs libcrc32c amdgpu amdkfd amd_iommu_v2 radeon hid_logitech_hidpp i2c_algo_bit drm_kms_helper crc32c_intel ttm drm r8169 mii hid_logitech_dj
kernel: CPU: 0 PID: 598 Comm: systemd-udevd Not tainted 4.13.10-200.fc26.x86_64 #1
kernel: Hardware name: ASUS All Series/AM1I-A, BIOS 0505 03/13/2014
kernel: task:
ffff979933b24c80 task.stack:
ffffaf83413a4000
kernel: RIP: 0010:usb_hcd_map_urb_for_dma+0x41d/0x620
systemd-fsck[659]: /dev/sda2: clean, 49/128016 files, 268609/512000 blocks
kernel: RSP: 0018:
ffffaf83413a7728 EFLAGS:
00010282
systemd-udevd[604]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
kernel: RAX:
000000000000001f RBX:
ffff979930bce780 RCX:
0000000000000000
kernel: RDX:
0000000000000000 RSI:
ffff97993ec0e118 RDI:
ffff97993ec0e118
kernel: RBP:
ffffaf83413a7768 R08:
000000000000039a R09:
0000000000000000
kernel: R10:
0000000000000001 R11:
00000000ffffffff R12:
00000000fffffff5
kernel: R13:
0000000001400000 R14:
0000000000000001 R15:
ffff979930806800
kernel: FS:
00007effaca5c8c0(0000) GS:
ffff97993ec00000(0000) knlGS:
0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
kernel: CR2:
00007effa9fca962 CR3:
0000000233089000 CR4:
00000000000406f0
kernel: Call Trace:
kernel: usb_hcd_submit_urb+0x493/0xb40
kernel: ? page_cache_tree_insert+0x100/0x100
kernel: ? xfs_iunlock+0xd5/0x100 [xfs]
kernel: ? xfs_file_buffered_aio_read+0x57/0xc0 [xfs]
kernel: usb_submit_urb+0x22d/0x560
kernel: usb_start_wait_urb+0x6e/0x180
kernel: usb_bulk_msg+0xb8/0x160
kernel: as102_send_ep1+0x49/0xe0 [dvb_as102]
kernel: ? devres_add+0x3f/0x50
kernel: as102_firmware_upload.isra.0+0x1dc/0x210 [dvb_as102]
kernel: as102_fw_upload+0xb6/0x1f0 [dvb_as102]
kernel: as102_dvb_register+0x2af/0x2d0 [dvb_as102]
kernel: as102_usb_probe+0x1f3/0x260 [dvb_as102]
kernel: usb_probe_interface+0x124/0x300
kernel: driver_probe_device+0x2ff/0x450
kernel: __driver_attach+0xa4/0xe0
kernel: ? driver_probe_device+0x450/0x450
kernel: bus_for_each_dev+0x6e/0xb0
kernel: driver_attach+0x1e/0x20
kernel: bus_add_driver+0x1c7/0x270
kernel: driver_register+0x60/0xe0
kernel: usb_register_driver+0x81/0x150
kernel: ? 0xffffffffc0807000
kernel: as102_usb_driver_init+0x1e/0x1000 [dvb_as102]
kernel: do_one_initcall+0x50/0x190
kernel: ? __vunmap+0x81/0xb0
kernel: ? kfree+0x154/0x170
kernel: ? kmem_cache_alloc_trace+0x15f/0x1c0
kernel: ? do_init_module+0x27/0x1e9
kernel: do_init_module+0x5f/0x1e9
kernel: load_module+0x2602/0x2c30
kernel: SYSC_init_module+0x170/0x1a0
kernel: ? SYSC_init_module+0x170/0x1a0
kernel: SyS_init_module+0xe/0x10
kernel: do_syscall_64+0x67/0x140
kernel: entry_SYSCALL64_slow_path+0x25/0x25
kernel: RIP: 0033:0x7effab6cf3ea
kernel: RSP: 002b:
00007fff5cfcbbc8 EFLAGS:
00000246 ORIG_RAX:
00000000000000af
kernel: RAX:
ffffffffffffffda RBX:
00005569e0b83760 RCX:
00007effab6cf3ea
kernel: RDX:
00007effac2099c5 RSI:
0000000000009a13 RDI:
00005569e0b98c50
kernel: RBP:
00007effac2099c5 R08:
00005569e0b83ed0 R09:
0000000000001d80
kernel: R10:
00007effab98db00 R11:
0000000000000246 R12:
00005569e0b98c50
kernel: R13:
00005569e0b81c60 R14:
0000000000020000 R15:
00005569dfadfdf7
kernel: Code: 48 39 c8 73 30 80 3d 59 60 9d 00 00 41 bc f5 ff ff ff 0f 85 26 ff ff ff 48 c7 c7 b8 6b d0 92 c6 05 3f 60 9d 00 01 e8 24 3d ad ff <0f> ff 8b 53 64 e9 09 ff ff ff 65 48 8b 0c 25 00 d3 00 00 48 8b
kernel: ---[ end trace
c4cae366180e70ec ]---
kernel: as10x_usb: error during firmware upload part1
Let's allocate the the structure dynamically so we can get the firmware
loaded correctly:
[ 14.243057] as10x_usb: firmware: as102_data1_st.hex loaded with success
[ 14.500777] as10x_usb: firmware: as102_data2_st.hex loaded with success
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Naveen N. Rao [Thu, 31 Aug 2017 16:25:57 +0000 (21:55 +0530)]
powerpc/signal: Properly handle return value from uprobe_deny_signal()
commit
46725b17f1c6c815a41429259b3f070c01e71bc1 upstream.
When a uprobe is installed on an instruction that we currently do not
emulate, we copy the instruction into a xol buffer and single step
that instruction. If that instruction generates a fault, we abort the
single stepping before invoking the signal handler. Once the signal
handler is done, the uprobe trap is hit again since the instruction is
retried and the process repeats.
We use uprobe_deny_signal() to detect if the xol instruction triggered
a signal. If so, we clear TIF_SIGPENDING and set TIF_UPROBE so that the
signal is not handled until after the single stepping is aborted. In
this case, uprobe_deny_signal() returns true and get_signal() ends up
returning 0. However, in do_signal(), we are not looking at the return
value, but depending on ksig.sig for further action, all with an
uninitialized ksig that is not touched in this scenario. Fix the same
by initializing ksig.sig to 0.
Fixes:
129b69df9c90 ("powerpc: Use get_signal() signal_setup_done()")
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John David Anglin [Sat, 11 Nov 2017 22:11:16 +0000 (17:11 -0500)]
parisc: Fix validity check of pointer size argument in new CAS implementation
commit
05f016d2ca7a4fab99d5d5472168506ddf95e74f upstream.
As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS
implementation causes a kernel crash. The attached patch corrects the
off by one error in the argument validity check.
In reviewing the code, I noticed that we only perform word operations
with the pointer size argument. The subi instruction intentionally uses
a word condition on 64-bit kernels. Nullification was used instead of a
cmpib instruction as the branch should never be taken. The shlw
pseudo-operation generates a depw,z instruction and it clears the target
before doing a shift left word deposit. Thus, we don't need to clip the
upper 32 bits of this argument on 64-bit kernels.
Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic
code in libgcc is the only direct user of the new CAS implementation
that I am aware of.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian King [Fri, 17 Nov 2017 17:05:43 +0000 (11:05 -0600)]
ixgbe: Fix skb list corruption on Power systems
commit
0a9a17e3bb4564caf4bfe2a6783ae1287667d188 upstream.
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian King [Fri, 17 Nov 2017 17:05:48 +0000 (11:05 -0600)]
fm10k: Use smp_rmb rather than read_barrier_depends
commit
7b8edcc685b5e2c3c37aa13dc50a88e84a5bfef8 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian King [Fri, 17 Nov 2017 17:05:49 +0000 (11:05 -0600)]
i40evf: Use smp_rmb rather than read_barrier_depends
commit
f72271e2a0ae4277d53c4053f5eed8bb346ba38a upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian King [Fri, 17 Nov 2017 17:05:45 +0000 (11:05 -0600)]
ixgbevf: Use smp_rmb rather than read_barrier_depends
commit
ae0c585d93dfaf923d2c7eb44b2c3ab92854ea9b upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian King [Fri, 17 Nov 2017 17:05:46 +0000 (11:05 -0600)]
igbvf: Use smp_rmb rather than read_barrier_depends
commit
1e1f9ca546556e508d021545861f6b5fc75a95fe upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian King [Fri, 17 Nov 2017 17:05:47 +0000 (11:05 -0600)]
igb: Use smp_rmb rather than read_barrier_depends
commit
c4cb99185b4cc96c0a1c70104dc21ae14d7e7f28 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian King [Fri, 17 Nov 2017 17:05:44 +0000 (11:05 -0600)]
i40e: Use smp_rmb rather than read_barrier_depends
commit
52c6912fde0133981ee50ba08808f257829c4c93 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 9 Jul 2017 11:08:58 +0000 (13:08 +0200)]
NFC: fix device-allocation error return
commit
c45e3e4c5b134b081e8af362109905427967eb19 upstream.
A recent change fixing NFC device allocation itself introduced an
error-handling bug by returning an error pointer in case device-id
allocation failed. This is clearly broken as the callers still expected
NULL to be returned on errors as detected by Dan's static checker.
Fix this up by returning NULL in the event that we've run out of memory
when allocating a new device id.
Note that the offending commit is marked for stable (3.8) so this fix
needs to be backported along with it.
Fixes:
20777bc57c34 ("NFC: fix broken device allocation")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Wed, 11 Oct 2017 17:27:26 +0000 (10:27 -0700)]
IB/srp: Avoid that a cable pull can trigger a kernel crash
commit
8a0d18c62121d3c554a83eb96e2752861d84d937 upstream.
This patch fixes the following kernel crash:
general protection fault: 0000 [#1] PREEMPT SMP
Workqueue: ib_mad2 timeout_sends [ib_core]
Call Trace:
ib_sa_path_rec_callback+0x1c4/0x1d0 [ib_core]
send_handler+0xb2/0xd0 [ib_core]
timeout_sends+0x14d/0x220 [ib_core]
process_one_work+0x200/0x630
worker_thread+0x4e/0x3b0
kthread+0x113/0x150
Fixes: commit
aef9ec39c47f ("IB: Add SCSI RDMA Protocol (SRP) initiator")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Wed, 11 Oct 2017 17:27:22 +0000 (10:27 -0700)]
IB/srpt: Do not accept invalid initiator port names
commit
c70ca38960399a63d5c048b7b700612ea321d17e upstream.
Make srpt_parse_i_port_id() return a negative value if hex2bin()
fails.
Fixes: commit
a42d985bd5b2 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Tue, 26 Sep 2017 18:21:24 +0000 (11:21 -0700)]
libnvdimm, namespace: make 'resource' attribute only readable by root
commit
c1fb3542074fd0c4d901d778bd52455111e4eb6f upstream.
For the same reason that /proc/iomem returns 0's for non-root readers
and acpi tables are root-only, make the 'resource' attribute for
namespace devices only readable by root. Otherwise we disclose physical
address information.
Fixes:
bf9bccc14c05 ("libnvdimm: pmem label sets and namespace instantiation")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Tue, 26 Sep 2017 18:41:28 +0000 (11:41 -0700)]
libnvdimm, namespace: fix label initialization to use valid seq numbers
commit
b18d4b8a25af6fe83d7692191d6ff962ea611c4f upstream.
The set of valid sequence numbers is {1,2,3}. The specification
indicates that an implementation should consider 0 a sign of a critical
error:
UEFI 2.7: 13.19 NVDIMM Label Protocol
Software never writes the sequence number 00, so a correctly
check-summed Index Block with this sequence number probably indicates a
critical error. When software discovers this case it treats it as an
invalid Index Block indication.
While the expectation is that the invalid block is just thrown away, the
Robustness Principle says we should fix this to make both sequence
numbers valid.
Fixes:
f524bf271a5c ("libnvdimm: write pmem label set")
Reported-by: Juston Li <juston.li@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sat, 11 Nov 2017 16:29:29 +0000 (17:29 +0100)]
clk: ti: dra7-atl-clock: fix child-node lookups
commit
33ec6dbc5a02677509d97fe36cd2105753f0f0ea upstream.
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes:
9ac33b0ce81f ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Fixes:
660e15519399 ("clk: ti: dra7-atl-clock: Fix of_node reference counting")
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Ujfalusi [Fri, 11 Mar 2016 14:13:32 +0000 (16:13 +0200)]
clk: ti: dra7-atl-clock: Fix of_node reference counting
commit
660e1551939931657808d47838a3f443c0e83fd0 upstream.
of_find_node_by_name() will call of_node_put() on the node so we need to
get it first to avoid warnings.
The cfg_node needs to be put after we have finished processing the
properties.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Tue, 10 Oct 2017 21:31:42 +0000 (17:31 -0400)]
SUNRPC: Fix tracepoint storage issues with svc_recv and svc_rqst_status
commit
e9d4bf219c83d09579bc62512fea2ca10f025d93 upstream.
There is no guarantee that either the request or the svc_xprt exist
by the time we get round to printing the trace message.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini [Thu, 26 Oct 2017 07:13:27 +0000 (09:13 +0200)]
KVM: SVM: obey guest PAT
commit
15038e14724799b8c205beb5f20f9e54896013c3 upstream.
For many years some users of assigned devices have reported worse
performance on AMD processors with NPT than on AMD without NPT,
Intel or bare metal.
The reason turned out to be that SVM is discarding the guest PAT
setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-,
PA3=UC). The guest might be using a different setting, and
especially might want write combining but isn't getting it
(instead getting slow UC or UC- accesses).
Thanks a lot to geoff@hostfission.com for noticing the relation
to the g_pat setting. The patch has been tested also by a bunch
of people on VFIO users forums.
Fixes:
709ddebf81cb40e3c36c6109a7892e8b93a09464
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Nick Sarnie <commendsarnex@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ladi Prosek [Wed, 11 Oct 2017 14:54:42 +0000 (16:54 +0200)]
KVM: nVMX: set IDTR and GDTR limits when loading L1 host state
commit
21f2d551183847bc7fbe8d866151d00cdad18752 upstream.
Intel SDM 27.5.2 Loading Host Segment and Descriptor-Table Registers:
"The GDTR and IDTR limits are each set to FFFFH."
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Bellinger [Fri, 22 Sep 2017 23:48:28 +0000 (16:48 -0700)]
target: Fix QUEUE_FULL + SCSI task attribute handling
commit
1c79df1f349fb6050016cea4ef1dfbc3853a5685 upstream.
This patch fixes a bug during QUEUE_FULL where transport_complete_qf()
calls transport_complete_task_attr() after it's already been invoked
by target_complete_ok_work() or transport_generic_request_failure()
during initial completion, preceeding QUEUE_FULL.
This will result in se_device->simple_cmds, se_device->dev_cur_ordered_id
and/or se_device->dev_ordered_sync being updated multiple times for
a single se_cmd.
To address this bug, clear SCF_TASK_ATTR_SET after the first call
to transport_complete_task_attr(), and avoid updating SCSI task
attribute related counters for any subsequent calls.
Also, when a se_cmd is deferred due to ordered tags and executed
via target_restart_delayed_cmds(), set CMD_T_SENT before execution
matching what target_execute_cmd() does.
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Bellinger [Sat, 28 Oct 2017 03:52:56 +0000 (20:52 -0700)]
iscsi-target: Fix non-immediate TMR reference leak
commit
3fc9fb13a4b2576aeab86c62fd64eb29ab68659c upstream.
This patch fixes a se_cmd->cmd_kref reference leak that can
occur when a non immediate TMR is proceeded our of command
sequence number order, and CMDSN_LOWER_THAN_EXP is returned
by iscsit_sequence_cmd().
To address this bug, call target_put_sess_cmd() during this
special case following what iscsit_process_scsi_cmd() does
upon CMDSN_LOWER_THAN_EXP.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuomas Tynkkynen [Wed, 6 Sep 2017 14:59:07 +0000 (17:59 +0300)]
fs/9p: Compare qid.path in v9fs_test_inode
commit
8ee031631546cf2f7859cc69593bd60bbdd70b46 upstream.
Commit
fd2421f54423 ("fs/9p: When doing inode lookup compare qid details
and inode mode bits.") transformed v9fs_qid_iget() to use iget5_locked()
instead of iget_locked(). However, the test() callback is not checking
fid.path at all, which means that a lookup in the inode cache can now
accidentally locate a completely wrong inode from the same inode hash
bucket if the other fields (qid.type and qid.version) match.
Fixes:
fd2421f54423 ("fs/9p: When doing inode lookup compare qid details and inode mode bits.")
Reviewed-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Sun, 24 Sep 2017 22:36:44 +0000 (18:36 -0400)]
fix a page leak in vhost_scsi_iov_to_sgl() error recovery
commit
11d49e9d089ccec81be87c2386dfdd010d7f7f6e upstream.
we are advancing sg as we go, so the pages we need to drop in
case of error are *before* the current sg.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kailang Yang [Wed, 22 Nov 2017 07:21:32 +0000 (15:21 +0800)]
ALSA: hda/realtek - Fix ALC700 family no sound issue
commit
2d7fe6185722b0817bb345f62ab06b76a7b26542 upstream.
It maybe the typo for ALC700 support patch.
To fix the bit value on this patch.
Fixes:
6fbae35a3170 ("ALSA: hda/realtek - Add support for new codecs ALC700/ALC701/ALC703")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 21 Nov 2017 15:36:11 +0000 (16:36 +0100)]
ALSA: timer: Remove kernel warning at compat ioctl error paths
commit
3d4e8303f2c747c8540a0a0126d0151514f6468b upstream.
Some timer compat ioctls have NULL checks of timer instance with
snd_BUG_ON() that bring up WARN_ON() when the debug option is set.
Actually the condition can be met in the normal situation and it's
confusing and bad to spew kernel warnings with stack trace there.
Let's remove snd_BUG_ON() invocation and replace with the simple
checks. Also, correct the error code to EBADFD to follow the native
ioctl error handling.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 21 Nov 2017 16:28:06 +0000 (17:28 +0100)]
ALSA: usb-audio: Add sanity checks in v2 clock parsers
commit
0a62d6c966956d77397c32836a5bbfe3af786fc1 upstream.
The helper functions to parse and look for the clock source, selector
and multiplier unit may return the descriptor with a too short length
than required, while there is no sanity check in the caller side.
Add some sanity checks in the parsers, at least, to guarantee the
given descriptor size, for avoiding the potential crashes.
Fixes:
79f920fbff56 ("ALSA: usb-audio: parse clock topology of UAC2 devices")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 21 Nov 2017 16:00:32 +0000 (17:00 +0100)]
ALSA: usb-audio: Fix potential out-of-bound access at parsing SU
commit
f658f17b5e0e339935dca23e77e0f3cad591926b upstream.
The usb-audio driver may trigger an out-of-bound access at parsing a
malformed selector unit, as it checks the header length only after
evaluating bNrInPins field, which can be already above the given
length. Fix it by adding the length check beforehand.
Fixes:
99fc86450c43 ("ALSA: usb-mixer: parse descriptors with structs")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 21 Nov 2017 15:55:51 +0000 (16:55 +0100)]
ALSA: usb-audio: Add sanity checks to FE parser
commit
d937cd6790a2bef2d07b500487646bd794c039bb upstream.
When the usb-audio descriptor contains the malformed feature unit
description with a too short length, the driver may access
out-of-bounds. Add a sanity check of the header size at the beginning
of parse_audio_feature_unit().
Fixes:
23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Henrik Eriksson [Tue, 21 Nov 2017 08:29:28 +0000 (09:29 +0100)]
ALSA: pcm: update tstamp only if audio_tstamp changed
commit
20e3f985bb875fea4f86b04eba4b6cc29bfd6b71 upstream.
commit
3179f6200188 ("ALSA: core: add .get_time_info") had a side effect
of changing the behaviour of the PCM runtime tstamp. Prior to this
change tstamp was not updated by snd_pcm_update_hw_ptr0() unless the
hw_ptr had moved, after this change tstamp was always updated.
For an application using alsa-lib, doing snd_pcm_readi() followed by
snd_pcm_status() to estimate the age of the read samples by subtracting
status->avail * [sample rate] from status->tstamp this change degraded
the accuracy of the estimate on devices where the pcm hw does not
provide a granular hw_ptr, e.g., devices using
soc-generic-dmaengine-pcm.c and a dma-engine with residue_granularity
DMA_RESIDUE_GRANULARITY_DESCRIPTOR. The accuracy of the estimate
depended on the latency between the PCM hw completing a period and the
driver called snd_pcm_period_elapsed() to notify ALSA core, typically
determined by interrupt handling latency. After the change the accuracy
of the estimate depended on the latency between the PCM hw completing a
period and the application calling snd_pcm_status(), determined by the
scheduling of the application process. The maximum error of the
estimate is one period length in both cases, but the error average and
variance is smaller when it depends on interrupt latency.
Instead of always updating tstamp, update it only if audio_tstamp
changed.
Fixes:
3179f6200188 ("ALSA: core: add .get_time_info")
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Henrik Eriksson <henrik.eriksson@axis.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Sat, 7 Oct 2017 03:09:55 +0000 (23:09 -0400)]
ext4: fix interaction between i_size, fallocate, and delalloc after a crash
commit
51e3ae81ec58e95f10a98ef3dd6d7bce5d8e35a2 upstream.
If there are pending writes subject to delayed allocation, then i_size
will show size after the writes have completed, while i_disksize
contains the value of i_size on the disk (since the writes have not
been persisted to disk).
If fallocate(2) is called with the FALLOC_FL_KEEP_SIZE flag, either
with or without the FALLOC_FL_ZERO_RANGE flag set, and the new size
after the fallocate(2) is between i_size and i_disksize, then after a
crash, if a journal commit has resulted in the changes made by the
fallocate() call to be persisted after a crash, but the delayed
allocation write has not resolved itself, i_size would not be updated,
and this would cause the following e2fsck complaint:
Inode 12, end of extent exceeds allowed value
(logical block 33, physical block 33441, len 7)
This can only take place on a sparse file, where the fallocate(2) call
is allocating blocks in a range which is before a pending delayed
allocation write which is extending i_size. Since this situation is
quite rare, and the window in which the crash must take place is
typically < 30 seconds, in practice this condition will rarely happen.
Nevertheless, it can be triggered in testing, and in particular by
xfstests generic/456.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rameshwar Prasad Sahu [Thu, 2 Nov 2017 11:01:07 +0000 (16:31 +0530)]
ata: fixes kernel crash while tracing ata_eh_link_autopsy event
commit
f1601113ddc0339a745e702f4fb1ca37d4875e65 upstream.
When tracing ata link error event, the kernel crashes when the disk is
removed due to NULL pointer access by trace_ata_eh_link_autopsy API.
This occurs as the dev is NULL when the disk disappeared. This patch
fixes this crash by calling trace_ata_eh_link_autopsy only if "dev"
is not NULL.
v2 changes:
Removed direct passing "link" pointer instead of "dev" in trace API.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes:
255c03d15a29 ("libata: Add tracepoints")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Mon, 6 Nov 2017 13:55:35 +0000 (14:55 +0100)]
rtlwifi: fix uninitialized rtlhal->last_suspend_sec time
commit
3f2a162fab15aee243178b5308bb5d1206fc4043 upstream.
We set rtlhal->last_suspend_sec to an uninitialized stack variable,
but unfortunately gcc never warned about this, I only found it
while working on another patch. I opened a gcc bug for this.
Presumably the value of rtlhal->last_suspend_sec is not all that
important, but it does get used, so we probably want the
patch backported to stable kernels.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Thu, 14 Sep 2017 18:17:44 +0000 (13:17 -0500)]
rtlwifi: rtl8192ee: Fix memory leak when loading firmware
commit
519ce2f933fa14acf69d5c8cabcc18711943d629 upstream.
In routine rtl92ee_set_fw_rsvdpagepkt(), the driver allocates an skb, but
never calls rtl_cmd_send_packet(), which will free the buffer. All other
rtlwifi drivers perform this operation correctly.
This problem has been in the driver since it was included in the kernel.
Fortunately, each firmware load only leaks 4 buffers, which likely
explains why it has not previously been detected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Elble [Fri, 3 Nov 2017 18:06:31 +0000 (14:06 -0400)]
nfsd: deal with revoked delegations appropriately
commit
95da1b3a5aded124dd1bda1e3cdb876184813140 upstream.
If a delegation has been revoked by the server, operations using that
delegation should error out with NFS4ERR_DELEG_REVOKED in the >4.1
case, and NFS4ERR_BAD_STATEID otherwise.
The server needs NFSv4.1 clients to explicitly free revoked delegations.
If the server returns NFS4ERR_DELEG_REVOKED, the client will do that;
otherwise it may just forget about the delegation and be unable to
recover when it later sees SEQ4_STATUS_RECALLABLE_STATE_REVOKED set on a
SEQUENCE reply. That can cause the Linux 4.1 client to loop in its
stage manager.
Signed-off-by: Andrew Elble <aweits@rit.edu>
Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuck Lever [Sun, 5 Nov 2017 20:45:22 +0000 (15:45 -0500)]
nfs: Fix ugly referral attributes
commit
c05cefcc72416a37eba5a2b35f0704ed758a9145 upstream.
Before traversing a referral and performing a mount, the mounted-on
directory looks strange:
dr-xr-xr-x. 2
4294967294 4294967294 0 Dec 31 1969 dir.0
nfs4_get_referral is wiping out any cached attributes with what was
returned via GETATTR(fs_locations), but the bit mask for that
operation does not request any file attributes.
Retrieve owner and timestamp information so that the memcpy in
nfs4_get_referral fills in more attributes.
Changes since v1:
- Don't request attributes that the client unconditionally replaces
- Request only MOUNTED_ON_FILEID or FILEID attribute, not both
- encode_fs_locations() doesn't use the third bitmask word
Fixes:
6b97fd3da1ea ("NFSv4: Follow a referral")
Suggested-by: Pradeep Thomas <pradeepthomas@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joshua Watt [Tue, 7 Nov 2017 22:25:47 +0000 (16:25 -0600)]
NFS: Fix typo in nomigration mount option
commit
f02fee227e5f21981152850744a6084ff3fa94ee upstream.
The option was incorrectly masking off all other options.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Thu, 19 Oct 2017 14:47:48 +0000 (16:47 +0200)]
isofs: fix timestamps beyond 2027
commit
34be4dbf87fc3e474a842305394534216d428f5d upstream.
isofs uses a 'char' variable to load the number of years since
1900 for an inode timestamp. On architectures that use a signed
char type by default, this results in an invalid date for
anything beyond 2027.
This changes the function argument to a 'u8' array, which
is defined the same way on all architectures, and unambiguously
lets us use years until 2155.
This should be backported to all kernels that might still be
in use by that date.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coly Li [Fri, 13 Oct 2017 23:35:29 +0000 (16:35 -0700)]
bcache: check ca->alloc_thread initialized before wake up it
commit
91af8300d9c1d7c6b6a2fd754109e08d4798b8d8 upstream.
In bcache code, sysfs entries are created before all resources get
allocated, e.g. allocation thread of a cache set.
There is posibility for NULL pointer deference if a resource is accessed
but which is not initialized yet. Indeed Jorg Bornschein catches one on
cache set allocation thread and gets a kernel oops.
The reason for this bug is, when bch_bucket_alloc() is called during
cache set registration and attaching, ca->alloc_thread is not properly
allocated and initialized yet, call wake_up_process() on ca->alloc_thread
triggers NULL pointer deference failure. A simple and fast fix is, before
waking up ca->alloc_thread, checking whether it is allocated, and only
wake up ca->alloc_thread when it is not NULL.
Signed-off-by: Coly Li <colyli@suse.de>
Reported-by: Jorg Bornschein <jb@capsec.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Tue, 22 Aug 2017 20:41:28 +0000 (23:41 +0300)]
eCryptfs: use after free in ecryptfs_release_messaging()
commit
db86be3a12d0b6e5c5b51c2ab2a48f06329cb590 upstream.
We're freeing the list iterator so we should be using the _safe()
version of hlist_for_each_entry().
Fixes:
88b4a07e6610 ("[PATCH] eCryptfs: Public key transport mechanism")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Rohner [Fri, 17 Nov 2017 23:29:35 +0000 (15:29 -0800)]
nilfs2: fix race condition that causes file system corruption
commit
31ccb1f7ba3cfe29631587d451cf5bb8ab593550 upstream.
There is a race condition between nilfs_dirty_inode() and
nilfs_set_file_dirty().
When a file is opened, nilfs_dirty_inode() is called to update the
access timestamp in the inode. It calls __nilfs_mark_inode_dirty() in a
separate transaction. __nilfs_mark_inode_dirty() caches the ifile
buffer_head in the i_bh field of the inode info structure and marks it
as dirty.
After some data was written to the file in another transaction, the
function nilfs_set_file_dirty() is called, which adds the inode to the
ns_dirty_files list.
Then the segment construction calls nilfs_segctor_collect_dirty_files(),
which goes through the ns_dirty_files list and checks the i_bh field.
If there is a cached buffer_head in i_bh it is not marked as dirty
again.
Since nilfs_dirty_inode() and nilfs_set_file_dirty() use separate
transactions, it is possible that a segment construction that writes out
the ifile occurs in-between the two. If this happens the inode is not
on the ns_dirty_files list, but its ifile block is still marked as dirty
and written out.
In the next segment construction, the data for the file is written out
and nilfs_bmap_propagate() updates the b-tree. Eventually the bmap root
is written into the i_bh block, which is not dirty, because it was
written out in another segment construction.
As a result the bmap update can be lost, which leads to file system
corruption. Either the virtual block address points to an unallocated
DAT block, or the DAT entry will be reused for something different.
The error can remain undetected for a long time. A typical error
message would be one of the "bad btree" errors or a warning that a DAT
entry could not be found.
This bug can be reproduced reliably by a simple benchmark that creates
and overwrites millions of 4k files.
Link: http://lkml.kernel.org/r/1509367935-3086-2-git-send-email-konishi.ryusuke@lab.ntt.co.jp
Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Andreas Rohner <andreas.rohner@gmx.net>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Fri, 17 Nov 2017 23:29:13 +0000 (15:29 -0800)]
autofs: don't fail mount for transient error
commit
ecc0c469f27765ed1e2b967be0aa17cee1a60b76 upstream.
Currently if the autofs kernel module gets an error when writing to the
pipe which links to the daemon, then it marks the whole moutpoint as
catatonic, and it will stop working.
It is possible that the error is transient. This can happen if the
daemon is slow and more than 16 requests queue up. If a subsequent
process tries to queue a request, and is then signalled, the write to
the pipe will return -ERESTARTSYS and autofs will take that as total
failure.
So change the code to assess -ERESTARTSYS and -ENOMEM as transient
failures which only abort the current request, not the whole mountpoint.
It isn't a crash or a data corruption, but having autofs mountpoints
suddenly stop working is rather inconvenient.
Ian said:
: And given the problems with a half dozen (or so) user space applications
: consuming large amounts of CPU under heavy mount and umount activity this
: could happen more easily than we expect.
Link: http://lkml.kernel.org/r/87y3norvgp.fsf@notabene.neil.brown.name
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mirko Parthey [Thu, 18 May 2017 19:30:03 +0000 (21:30 +0200)]
MIPS: BCM47XX: Fix LED inversion for WRT54GSv1
commit
56a46acf62af5ba44fca2f3f1c7c25a2d5385b19 upstream.
The WLAN LED on the Linksys WRT54GSv1 is active low, but the software
treats it as active high. Fix the inverted logic.
Fixes:
7bb26b169116 ("MIPS: BCM47xx: Fix LEDs on WRT54GS V1.0")
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Looks-ok-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16071/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maciej W. Rozycki [Tue, 7 Nov 2017 19:09:20 +0000 (19:09 +0000)]
MIPS: Fix an n32 core file generation regset support regression
commit
547da673173de51f73887377eb275304775064ad upstream.
Fix a commit
7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
regression, then activated by commit
6a9c001b7ec3 ("MIPS: Switch ELF
core dumper to use regsets.)", that caused n32 processes to dump o32
core files by failing to set the EF_MIPS_ABI2 flag in the ELF core file
header's `e_flags' member:
$ file tls-core
tls-core: ELF 32-bit MSB executable, MIPS, N32 MIPS64 rel2 version 1 (SYSV), [...]
$ ./tls-core
Aborted (core dumped)
$ file core
core: ELF 32-bit MSB core file MIPS, MIPS-I version 1 (SYSV), SVR4-style
$
Previously the flag was set as the result of a:
statement placed in arch/mips/kernel/binfmt_elfn32.c, however in the
regset case, i.e. when CORE_DUMP_USE_REGSET is set, ELF_CORE_EFLAGS is
no longer used by `fill_note_info' in fs/binfmt_elf.c, and instead the
`->e_flags' member of the regset view chosen is. We have the views
defined in arch/mips/kernel/ptrace.c, however only an o32 and an n64
one, and the latter is used for n32 as well. Consequently an o32 core
file is incorrectly dumped from n32 processes (the ELF32 vs ELF64 class
is chosen elsewhere, and the 32-bit one is correctly selected for n32).
Correct the issue then by defining an n32 regset view and using it as
appropriate. Issue discovered in GDB testing.
Fixes:
7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Djordje Todorovic <djordje.todorovic@rt-rk.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17617/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hou Tao [Wed, 1 Nov 2017 07:42:36 +0000 (15:42 +0800)]
dm: fix race between dm_get_from_kobject() and __dm_destroy()
commit
b9a41d21dceadf8104812626ef85dc56ee8a60ed upstream.
The following BUG_ON was hit when testing repeat creation and removal of
DM devices:
kernel BUG at drivers/md/dm.c:2919!
CPU: 7 PID: 750 Comm: systemd-udevd Not tainted 4.1.44
Call Trace:
[<
ffffffff81649e8b>] dm_get_from_kobject+0x34/0x3a
[<
ffffffff81650ef1>] dm_attr_show+0x2b/0x5e
[<
ffffffff817b46d1>] ? mutex_lock+0x26/0x44
[<
ffffffff811df7f5>] sysfs_kf_seq_show+0x83/0xcf
[<
ffffffff811de257>] kernfs_seq_show+0x23/0x25
[<
ffffffff81199118>] seq_read+0x16f/0x325
[<
ffffffff811de994>] kernfs_fop_read+0x3a/0x13f
[<
ffffffff8117b625>] __vfs_read+0x26/0x9d
[<
ffffffff8130eb59>] ? security_file_permission+0x3c/0x44
[<
ffffffff8117bdb8>] ? rw_verify_area+0x83/0xd9
[<
ffffffff8117be9d>] vfs_read+0x8f/0xcf
[<
ffffffff81193e34>] ? __fdget_pos+0x12/0x41
[<
ffffffff8117c686>] SyS_read+0x4b/0x76
[<
ffffffff817b606e>] system_call_fastpath+0x12/0x71
The bug can be easily triggered, if an extra delay (e.g. 10ms) is added
between the test of DMF_FREEING & DMF_DELETING and dm_get() in
dm_get_from_kobject().
To fix it, we need to ensure the test of DMF_FREEING & DMF_DELETING and
dm_get() are done in an atomic way, so _minor_lock is used.
The other callers of dm_get() have also been checked to be OK: some
callers invoke dm_get() under _minor_lock, some callers invoke it under
_hash_lock, and dm_start_request() invoke it after increasing
md->open_count.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Thu, 16 Nov 2017 00:38:09 +0000 (16:38 -0800)]
dm bufio: fix integer overflow when limiting maximum cache size
commit
74d4108d9e681dbbe4a2940ed8fdff1f6868184c upstream.
The default max_cache_size_bytes for dm-bufio is meant to be the lesser
of 25% of the size of the vmalloc area and 2% of the size of lowmem.
However, on 32-bit systems the intermediate result in the expression
(VMALLOC_END - VMALLOC_START) * DM_BUFIO_VMALLOC_PERCENT / 100
overflows, causing the wrong result to be computed. For example, on a
32-bit system where the vmalloc area is
520093696 bytes, the result is
1174405 rather than the expected
130023424, which makes the maximum
cache size much too small (far less than 2% of lowmem). This causes
severe performance problems for dm-verity users on affected systems.
Fix this by using mult_frac() to correctly multiply by a percentage. Do
this for all places in dm-bufio that multiply by a percentage. Also
replace (VMALLOC_END - VMALLOC_START) with VMALLOC_TOTAL, which contrary
to the comment is now defined in include/linux/vmalloc.h.
Depends-on:
9993bc635 ("sched/x86: Fix overflow in cyc2ns_offset")
Fixes:
95d402f057f2 ("dm: add bufio")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vijendar Mukunda [Thu, 23 Nov 2017 14:37:00 +0000 (20:07 +0530)]
ALSA: hda: Add Raven PCI ID
commit
9ceace3c9c18c67676e75141032a65a8e01f9a7a upstream.
This commit adds PCI ID for Raven platform
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Kresin [Thu, 11 May 2017 06:11:15 +0000 (08:11 +0200)]
MIPS: ralink: Fix typo in mt7628 pinmux function
commit
05a67cc258e75ac9758e6f13d26337b8be51162a upstream.
There is a typo inside the pinmux setup code. The function is called
refclk and not reclk.
Fixes:
53263a1c6852 ("MIPS: ralink: add mt7628an support")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16047/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Kresin [Thu, 11 May 2017 06:11:14 +0000 (08:11 +0200)]
MIPS: ralink: Fix MT7628 pinmux
commit
8ef4b43cd3794d63052d85898e42424fd3b14d24 upstream.
According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.
Fixes:
53263a1c6852 ("MIPS: ralink: add mt7628an support")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16046/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philip Derrin [Mon, 13 Nov 2017 23:55:26 +0000 (00:55 +0100)]
ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
commit
3b0c0c922ff4be275a8beb87ce5657d16f355b54 upstream.
When CONFIG_ARM_LPAE is set, the PMD dump relies on the software
read-only bit to determine whether a page is writable. This
concealed a bug which left the kernel text section writable
(AP2=0) while marked read-only in the software bit.
In a kernel with the AP2 bug, the dump looks like this:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M ro x SHD
0xc0600000-0xc0800000 2M ro NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
The fix is to check that the software and hardware bits are both
set before displaying "ro". The dump then shows the true perms:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M RW x SHD
0xc0600000-0xc0800000 2M RW NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
Fixes:
ded947798469 ("ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE")
Signed-off-by: Philip Derrin <philip@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philip Derrin [Mon, 13 Nov 2017 23:55:25 +0000 (00:55 +0100)]
ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
commit
400eeffaffc7232c0ae1134fe04e14ae4fb48d8c upstream.
Currently, for ARM kernels with CONFIG_ARM_LPAE and
CONFIG_STRICT_KERNEL_RWX enabled, the 2MiB pages mapping the
kernel code and rodata are writable. They are marked read-only in
a software bit (L_PMD_SECT_RDONLY) but the hardware read-only bit
is not set (PMD_SECT_AP2).
For user mappings, the logic that propagates the software bit
to the hardware bit is in set_pmd_at(); but for the kernel,
section_update() writes the PMDs directly, skipping this logic.
The fix is to set PMD_SECT_AP2 for read-only sections in
section_update(), at the same time as L_PMD_SECT_RDONLY.
Fixes:
1e3479225acb ("ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error")
Signed-off-by: Philip Derrin <philip@cog.systems>
Reported-by: Neil Dick <neil@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masami Hiramatsu [Fri, 24 Nov 2017 04:56:30 +0000 (13:56 +0900)]
x86/decoder: Add new TEST instruction pattern
commit
12a78d43de767eaf8fb272facb7a7b6f2dc6a9df upstream.
The kbuild test robot reported this build warning:
Warning: arch/x86/tools/test_get_len found difference at <jump_table>:
ffffffff8103dd2c
Warning:
ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
Warning: objdump says 3 bytes, but insn_get_length() says 2
Warning: decoded and checked
1569014 instructions with 1 warnings
This sequence seems to be a new instruction not in the opcode map in the Intel SDM.
The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"
In that table, opcodes listed by the index REG bits as:
000 001 010 011 100 101 110 111
TEST Ib/Iz,(undefined),NOT,NEG,MUL AL/rAX,IMUL AL/rAX,DIV AL/rAX,IDIV AL/rAX
So, it seems TEST Ib is assigned to 001.
Add the new pattern.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Tue, 7 Nov 2017 22:15:27 +0000 (14:15 -0800)]
lib/mpi: call cond_resched() from mpi_powm() loop
commit
1d9ddde12e3c9bab7f3d3484eb9446315e3571ca upstream.
On a non-preemptible kernel, if KEYCTL_DH_COMPUTE is called with the
largest permitted inputs (16384 bits), the kernel spends 10+ seconds
doing modular exponentiation in mpi_powm() without rescheduling. If all
threads do it, it locks up the system. Moreover, it can cause
rcu_sched-stall warnings.
Notwithstanding the insanity of doing this calculation in kernel mode
rather than in userspace, fix it by calling cond_resched() as each bit
from the exponent is processed. It's still noninterruptible, but at
least it's preemptible now.
Do the cond_resched() once per bit rather than once per MPI limb because
each limb might still easily take 100+ milliseconds on slow CPUs.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul E. McKenney [Mon, 18 Sep 2017 15:54:40 +0000 (08:54 -0700)]
sched: Make resched_cpu() unconditional
commit
7c2102e56a3f7d85b5d8f33efbd7aecc1f36fdd8 upstream.
The current implementation of synchronize_sched_expedited() incorrectly
assumes that resched_cpu() is unconditional, which it is not. This means
that synchronize_sched_expedited() can hang when resched_cpu()'s trylock
fails as follows (analysis by Neeraj Upadhyay):
o CPU1 is waiting for expedited wait to complete:
sync_rcu_exp_select_cpus
rdp->exp_dynticks_snap & 0x1 // returns 1 for CPU5
IPI sent to CPU5
synchronize_sched_expedited_wait
ret = swait_event_timeout(rsp->expedited_wq,
sync_rcu_preempt_exp_done(rnp_root),
jiffies_stall);
expmask = 0x20, CPU 5 in idle path (in cpuidle_enter())
o CPU5 handles IPI and fails to acquire rq lock.
Handles IPI
sync_sched_exp_handler
resched_cpu
returns while failing to try lock acquire rq->lock
need_resched is not set
o CPU5 calls rcu_idle_enter() and as need_resched is not set, goes to
idle (schedule() is not called).
o CPU 1 reports RCU stall.
Given that resched_cpu() is now used only by RCU, this commit fixes the
assumption by making resched_cpu() unconditional.
Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Suggested-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WANG Cong [Fri, 19 May 2017 18:21:59 +0000 (11:21 -0700)]
vsock: use new wait API for vsock_stream_sendmsg()
commit
499fde662f1957e3cb8d192a94a099ebe19c714b upstream.
As reported by Michal, vsock_stream_sendmsg() could still
sleep at vsock_stream_has_space() after prepare_to_wait():
vsock_stream_has_space
vmci_transport_stream_has_space
vmci_qpair_produce_free_space
qp_lock
qp_acquire_queue_mutex
mutex_lock
Just switch to the new wait API like we did for commit
d9dc8b0f8b4e ("net: fix sleeping for sk_wait_event()").
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: "Jorgen S. Hansen" <jhansen@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Claudio Imbrenda [Tue, 22 Mar 2016 16:05:52 +0000 (17:05 +0100)]
AF_VSOCK: Shrink the area influenced by prepare_to_wait
commit
f7f9b5e7f8eccfd68ffa7b8d74b07c478bb9e7f0 upstream.
When a thread is prepared for waiting by calling prepare_to_wait, sleeping
is not allowed until either the wait has taken place or finish_wait has
been called. The existing code in af_vsock imposed unnecessary no-sleep
assumptions to a broad list of backend functions.
This patch shrinks the influence of prepare_to_wait to the area where it
is strictly needed, therefore relaxing the no-sleep restriction there.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: "Jorgen S. Hansen" <jhansen@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WANG Cong [Tue, 20 Jun 2017 18:42:27 +0000 (11:42 -0700)]
ipv6: only call ip6_route_dev_notify() once for NETDEV_UNREGISTER
commit
76da0704507bbc51875013f6557877ab308cfd0a upstream.
In commit
242d3a49a2a1 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
I assumed NETDEV_REGISTER and NETDEV_UNREGISTER are paired,
unfortunately, as reported by jeffy, netdev_wait_allrefs()
could rebroadcast NETDEV_UNREGISTER event until all refs are
gone.
We have to add an additional check to avoid this corner case.
For netdev_wait_allrefs() dev->reg_state is NETREG_UNREGISTERED,
for dev_change_net_namespace(), dev->reg_state is
NETREG_REGISTERED. So check for dev->reg_state != NETREG_UNREGISTERED.
Fixes:
242d3a49a2a1 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
Reported-by: jeffy <jeffy.chen@rock-chips.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vasily Gorbik [Wed, 15 Nov 2017 13:15:36 +0000 (14:15 +0100)]
s390/disassembler: increase show_code buffer size
commit
b192571d1ae375e0bbe0aa3ccfa1a3c3704454b9 upstream.
Current buffer size of 64 is too small. objdump shows that there are
instructions which would require up to 75 bytes buffer (with current
formating). 128 bytes "ought to be enough for anybody".
Also replaces 8 spaces with a single tab to reduce the memory footprint.
Fixes the following KASAN finding:
BUG: KASAN: stack-out-of-bounds in number+0x3fe/0x538
Write of size 1 at addr
000000005a4a75a0 by task bash/1282
CPU: 1 PID: 1282 Comm: bash Not tainted 4.14.0+ #215
Hardware name: IBM 2964 N96 702 (z/VM 6.4.0)
Call Trace:
([<
000000000011eeb6>] show_stack+0x56/0x88)
[<
0000000000e1ce1a>] dump_stack+0x15a/0x1b0
[<
00000000004e2994>] print_address_description+0xf4/0x288
[<
00000000004e2cf2>] kasan_report+0x13a/0x230
[<
0000000000e38ae6>] number+0x3fe/0x538
[<
0000000000e3dfe4>] vsnprintf+0x194/0x948
[<
0000000000e3ea42>] sprintf+0xa2/0xb8
[<
00000000001198dc>] print_insn+0x374/0x500
[<
0000000000119346>] show_code+0x4ee/0x538
[<
000000000011f234>] show_registers+0x34c/0x388
[<
000000000011f2ae>] show_regs+0x3e/0xa8
[<
000000000011f502>] die+0x1ea/0x2e8
[<
0000000000138f0e>] do_no_context+0x106/0x168
[<
0000000000139a1a>] do_protection_exception+0x4da/0x7d0
[<
0000000000e55914>] pgm_check_handler+0x16c/0x1c0
[<
000000000090639e>] sysrq_handle_crash+0x46/0x58
([<
0000000000000007>] 0x7)
[<
00000000009073fa>] __handle_sysrq+0x102/0x218
[<
0000000000907c06>] write_sysrq_trigger+0xd6/0x100
[<
000000000061d67a>] proc_reg_write+0xb2/0x128
[<
0000000000520be6>] __vfs_write+0xee/0x368
[<
0000000000521222>] vfs_write+0x21a/0x278
[<
000000000052156a>] SyS_write+0xda/0x178
[<
0000000000e555cc>] system_call+0xc4/0x270
The buggy address belongs to the page:
page:
000003d1016929c0 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
raw:
0000000000000000 0000000000000000 0000000000000000 ffffffff00000000
raw:
0000000000000100 0000000000000200 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
000000005a4a7480: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
000000005a4a7500: 00 00 00 00 00 00 00 00 f2 f2 f2 f2 00 00 00 00
>
000000005a4a7580: 00 00 00 00 f3 f3 f3 f3 00 00 00 00 00 00 00 00
^
000000005a4a7600: 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 f8 f8
000000005a4a7680: f2 f2 f2 f2 f2 f2 f8 f8 f2 f2 f3 f3 f3 f3 00 00
==================================================================
Signed-off-by: Vasily Gorbik <gor@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Carstens [Tue, 26 Sep 2017 07:16:48 +0000 (09:16 +0200)]
s390/disassembler: add missing end marker for e7 table
commit
5c50538752af7968f53924b22dede8ed4ce4cb3b upstream.
The e7 opcode table does not have an end marker. Hence when trying to
find an unknown e7 instruction the code will access memory behind the
table until it finds something that matches the opcode, or the kernel
crashes, whatever comes first.
This affects not only the in-kernel disassembler but also uprobes and
kprobes which refuse to set a probe on unknown instructions, and
therefore search the opcode tables to figure out if instructions are
known or not.
Fixes:
3585cb0280654 ("s390/disassembler: add vector instructions")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Carstens [Mon, 11 Sep 2017 09:24:22 +0000 (11:24 +0200)]
s390/runtime instrumention: fix possible memory corruption
commit
d6e646ad7cfa7034d280459b2b2546288f247144 upstream.
For PREEMPT enabled kernels the runtime instrumentation (RI) code
contains a possible use-after-free bug. If a task that makes use of RI
exits, it will execute do_exit() while still enabled for preemption.
That function will call exit_thread_runtime_instr() via
exit_thread(). If exit_thread_runtime_instr() gets preempted after the
RI control block of the task has been freed but before the pointer to
it is set to NULL, then save_ri_cb(), called from switch_to(), will
write to already freed memory.
Avoid this and simply disable preemption while freeing the control
block and setting the pointer to NULL.
Fixes:
e4b8b3f33fca ("s390: add support for runtime instrumentation")
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Carstens [Thu, 9 Nov 2017 11:29:34 +0000 (12:29 +0100)]
s390: fix transactional execution control register handling
commit
a1c5befc1c24eb9c1ee83f711e0f21ee79cbb556 upstream.
Dan Horák reported the following crash related to transactional execution:
User process fault: interruption code 0013 ilc:3 in libpthread-2.26.so[
3ff93c00000+1b000]
CPU: 2 PID: 1 Comm: /init Not tainted 4.13.4-300.fc27.s390x #1
Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
task:
00000000fafc8000 task.stack:
00000000fafc4000
User PSW :
0705200180000000 000003ff93c14e70
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:1 AS:0 CC:2 PM:0 RI:0 EA:3
User GPRS:
0000000000000077 000003ff00000000 000003ff93144d48 000003ff93144d5e
0000000000000000 0000000000000002 0000000000000000 000003ff00000000
0000000000000000 0000000000000418 0000000000000000 000003ffcc9fe770
000003ff93d28f50 000003ff9310acf0 000003ff92b0319a 000003ffcc9fe6d0
User Code:
000003ff93c14e62:
60e0b030 std %f14,48(%r11)
000003ff93c14e66:
60f0b038 std %f15,56(%r11)
#
000003ff93c14e6a:
e5600000ff0e tbegin 0,65294
>
000003ff93c14e70:
a7740006 brc 7,
3ff93c14e7c
000003ff93c14e74:
a7080000 lhi %r0,0
000003ff93c14e78:
a7f40023 brc 15,
3ff93c14ebe
000003ff93c14e7c:
b2220000 ipm %r0
000003ff93c14e80:
8800001c srl %r0,28
There are several bugs with control register handling with respect to
transactional execution:
- on task switch update_per_regs() is only called if the next task has
an mm (is not a kernel thread). This however is incorrect. This
breaks e.g. for user mode helper handling, where the kernel creates
a kernel thread and then execve's a user space program. Control
register contents related to transactional execution won't be
updated on execve. If the previous task ran with transactional
execution disabled then the new task will also run with
transactional execution disabled, which is incorrect. Therefore call
update_per_regs() unconditionally within switch_to().
- on startup the transactional execution facility is not enabled for
the idle thread. This is not really a bug, but an inconsistency to
other facilities. Therefore enable the facility if it is available.
- on fork the new thread's per_flags field is not cleared. This means
that a child process inherits the PER_FLAG_NO_TE flag. This flag can
be set with a ptrace request to disable transactional execution for
the current process. It should not be inherited by new child
processes in order to be consistent with the handling of all other
PER related debugging options. Therefore clear the per_flags field in
copy_thread_tls().
Reported-and-tested-by: Dan Horák <dan@danny.cz>
Fixes:
d35339a42dd1 ("s390: add support for transactional memory")
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 24 Nov 2017 10:26:29 +0000 (11:26 +0100)]
Linux 4.4.102
Michal Hocko [Fri, 24 Nov 2017 10:13:07 +0000 (11:13 +0100)]
mm, hwpoison: fixup "mm: check the return value of lookup_page_ext for all call sites"
Backport of the upstream commit
f86e4271978b ("mm: check the return
value of lookup_page_ext for all call sites") is wrong for hwpoison
pages. I have accidentally negated the condition for bailout. This
basically disables hwpoison pages tracking while the code still
might crash on unusual configurations when struct pages do not have
page_ext allocated. The fix is trivial to invert the condition.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 24 Nov 2017 07:32:25 +0000 (08:32 +0100)]
Linux 4.4.101
Jann Horn [Tue, 14 Nov 2017 00:03:44 +0000 (01:03 +0100)]
mm/pagewalk.c: report holes in hugetlb ranges
commit
373c4557d2aa362702c4c2d41288fb1e54990b7c upstream.
This matters at least for the mincore syscall, which will otherwise copy
uninitialized memory from the page allocator to userspace. It is
probably also a correctness error for /proc/$pid/pagemap, but I haven't
tested that.
Removing the `walk->hugetlb_entry` condition in walk_hugetlb_range() has
no effect because the caller already checks for that.
This only reports holes in hugetlb ranges to callers who have specified
a hugetlb_entry callback.
This issue was found using an AFL-based fuzzer.
v2:
- don't crash on ->pte_hole==NULL (Andrew Morton)
- add Cc stable (Andrew Morton)
Changed for 4.4/4.9 stable backport:
- fix up conflict in the huge_pte_offset() call
Fixes:
1e25a271c8ac ("mincore: apply page table walker on do_mincore()")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jaewon Kim [Thu, 16 Nov 2017 01:39:07 +0000 (17:39 -0800)]
mm/page_ext.c: check if page_ext is not prepared
commit
e492080e640c2d1235ddf3441cae634cfffef7e1 upstream.
online_page_ext() and page_ext_init() allocate page_ext for each
section, but they do not allocate if the first PFN is !pfn_present(pfn)
or !pfn_valid(pfn). Then section->page_ext remains as NULL.
lookup_page_ext checks NULL only if CONFIG_DEBUG_VM is enabled. For a
valid PFN, __set_page_owner will try to get page_ext through
lookup_page_ext. Without CONFIG_DEBUG_VM lookup_page_ext will misuse
NULL pointer as value 0. This incurrs invalid address access.
This is the panic example when PFN 0x100000 is not valid but PFN
0x13FC00 is being used for page_ext. section->page_ext is NULL,
get_entry returned invalid page_ext address as 0x1DFA000 for a PFN
0x13FC00.
To avoid this panic, CONFIG_DEBUG_VM should be removed so that page_ext
will be checked at all times.
Unable to handle kernel paging request at virtual address
01dfa014
------------[ cut here ]------------
Kernel BUG at
ffffff80082371e0 [verbose debug info unavailable]
Internal error: Oops:
96000045 [#1] PREEMPT SMP
Modules linked in:
PC is at __set_page_owner+0x48/0x78
LR is at __set_page_owner+0x44/0x78
__set_page_owner+0x48/0x78
get_page_from_freelist+0x880/0x8e8
__alloc_pages_nodemask+0x14c/0xc48
__do_page_cache_readahead+0xdc/0x264
filemap_fault+0x2ac/0x550
ext4_filemap_fault+0x3c/0x58
__do_fault+0x80/0x120
handle_mm_fault+0x704/0xbb0
do_page_fault+0x2e8/0x394
do_mem_abort+0x88/0x124
Pre-4.7 kernels also need commit
f86e4271978b ("mm: check the return
value of lookup_page_ext for all call sites").
Link: http://lkml.kernel.org/r/20171107094131.14621-1-jaewon31.kim@samsung.com
Fixes:
eefa864b701d ("mm/page_ext: resurrect struct page extending code for debugging")
Signed-off-by: Jaewon Kim <jaewon31.kim@samsung.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yang Shi [Fri, 3 Jun 2016 21:55:38 +0000 (14:55 -0700)]
mm: check the return value of lookup_page_ext for all call sites
commit
f86e4271978bd93db466d6a95dad4b0fdcdb04f6 upstream.
Per the discussion with Joonsoo Kim [1], we need check the return value
of lookup_page_ext() for all call sites since it might return NULL in
some cases, although it is unlikely, i.e. memory hotplug.
Tested with ltp with "page_owner=0".
[1] http://lkml.kernel.org/r/
20160519002809.GA10245@js1304-P5Q-DELUXE
[akpm@linux-foundation.org: fix build-breaking typos]
[arnd@arndb.de: fix build problems from lookup_page_ext]
Link: http://lkml.kernel.org/r/6285269.2CksypHdYp@wuerfel
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1464023768-31025-1-git-send-email-yang.shi@linaro.org
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Harkes [Wed, 27 Sep 2017 19:52:12 +0000 (15:52 -0400)]
coda: fix 'kernel memory exposure attempt' in fsync
commit
d337b66a4c52c7b04eec661d86c2ef6e168965a2 upstream.
When an application called fsync on a file in Coda a small request with
just the file identifier was allocated, but the declared length was set
to the size of union of all possible upcall requests.
This bug has been around for a very long time and is now caught by the
extra checking in usercopy that was introduced in Linux-4.8.
The exposure happens when the Coda cache manager process reads the fsync
upcall request at which point it is killed. As a result there is nobody
servicing any further upcalls, trapping any processes that try to access
the mounted Coda filesystem.
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Tatashin [Thu, 16 Nov 2017 01:38:41 +0000 (17:38 -0800)]
mm/page_alloc.c: broken deferred calculation
commit
d135e5750205a21a212a19dbb05aeb339e2cbea7 upstream.
In reset_deferred_meminit() we determine number of pages that must not
be deferred. We initialize pages for at least 2G of memory, but also
pages for reserved memory in this node.
The reserved memory is determined in this function:
memblock_reserved_memory_within(), which operates over physical
addresses, and returns size in bytes. However, reset_deferred_meminit()
assumes that that this function operates with pfns, and returns page
count.
The result is that in the best case machine boots slower than expected
due to initializing more pages than needed in single thread, and in the
worst case panics because fewer than needed pages are initialized early.
Link: http://lkml.kernel.org/r/20171021011707.15191-1-pasha.tatashin@oracle.com
Fixes:
864b9a393dcb ("mm: consider memblock reservations for deferred memory initialization sizing")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corey Minyard [Sun, 30 Jul 2017 02:14:55 +0000 (21:14 -0500)]
ipmi: fix unsigned long underflow
commit
392a17b10ec4320d3c0e96e2a23ebaad1123b989 upstream.
When I set the timeout to a specific value such as 500ms, the timeout
event will not happen in time due to the overflow in function
check_msg_timeout:
...
ent->timeout -= timeout_period;
if (ent->timeout > 0)
return;
...
The type of timeout_period is long, but ent->timeout is unsigned long.
This patch makes the type consistent.
Reported-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alex chen [Thu, 16 Nov 2017 01:31:40 +0000 (17:31 -0800)]
ocfs2: should wait dio before inode lock in ocfs2_setattr()
commit
28f5a8a7c033cbf3e32277f4cc9c6afd74f05300 upstream.
we should wait dio requests to finish before inode lock in
ocfs2_setattr(), otherwise the following deadlock will happen:
process 1 process 2 process 3
truncate file 'A' end_io of writing file 'A' receiving the bast messages
ocfs2_setattr
ocfs2_inode_lock_tracker
ocfs2_inode_lock_full
inode_dio_wait
__inode_dio_wait
-->waiting for all dio
requests finish
dlm_proxy_ast_handler
dlm_do_local_bast
ocfs2_blocking_ast
ocfs2_generic_handle_bast
set OCFS2_LOCK_BLOCKED flag
dio_end_io
dio_bio_end_aio
dio_complete
ocfs2_dio_end_io
ocfs2_dio_end_io_write
ocfs2_inode_lock
__ocfs2_cluster_lock
ocfs2_wait_for_mask
-->waiting for OCFS2_LOCK_BLOCKED
flag to be cleared, that is waiting
for 'process 1' unlocking the inode lock
inode_dio_end
-->here dec the i_dio_count, but will never
be called, so a deadlock happened.
Link: http://lkml.kernel.org/r/59F81636.70508@huawei.com
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Acked-by: Changwei Ge <ge.changwei@h3c.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keith Busch [Thu, 16 Nov 2017 23:57:10 +0000 (16:57 -0700)]
nvme: Fix memory order on async queue deletion
This patch is a fix specific to the 3.19 - 4.4 kernels. The 4.5 kernel
inadvertently fixed this bug differently (
db3cbfff5bcc0), but is not
a stable candidate due it being a complicated re-write of the entire
feature.
This patch fixes a potential timing bug with nvme's asynchronous queue
deletion, which causes an allocated request to be accidentally released
due to the ordering of the shared completion context among the sq/cq
pair. The completion context saves the request that issued the queue
deletion. If the submission side deletion happens to reset the active
request, the completion side will release the wrong request tag back into
the pool of available tags. This means the driver will create multiple
commands with the same tag, corrupting the queue context.
The error is observable in the kernel logs like:
"nvme XX:YY:ZZ completed id XX twice on qid:0"
In this particular case, this message occurs because the queue is
corrupted.
The following timing sequence demonstrates the error:
CPU A CPU B
----------------------- -----------------------------
nvme_irq
nvme_process_cq
async_completion
queue_kthread_work -----------> nvme_del_sq_work_handler
nvme_delete_cq
adapter_async_del_queue
nvme_submit_admin_async_cmd
cmdinfo->req = req;
blk_mq_free_request(cmdinfo->req); <-- wrong request!!!
This patch fixes the bug by releasing the request in the completion side
prior to waking the submission thread, such that that thread can't muck
with the shared completion context.
Fixes:
a4aea5623d4a5 ("NVMe: Convert to blk-mq")
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Rutland [Mon, 13 Jun 2016 10:15:14 +0000 (11:15 +0100)]
arm64: fix dump_instr when PAN and UAO are in use
commit
c5cea06be060f38e5400d796e61cfc8c36e52924 upstream.
If the kernel is set to show unhandled signals, and a user task does not
handle a SIGILL as a result of an instruction abort, we will attempt to
log the offending instruction with dump_instr before killing the task.
We use dump_instr to log the encoding of the offending userspace
instruction. However, dump_instr is also used to dump instructions from
kernel space, and internally always switches to KERNEL_DS before dumping
the instruction with get_user. When both PAN and UAO are in use, reading
a user instruction via get_user while in KERNEL_DS will result in a
permission fault, which leads to an Oops.
As we have regs corresponding to the context of the original instruction
abort, we can inspect this and only flip to KERNEL_DS if the original
abort was taken from the kernel, avoiding this issue. At the same time,
remove the redundant (and incorrect) comments regarding the order
dump_mem and dump_instr are called in.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Fixes:
57f4959bad0a154a ("arm64: kernel: Add support for User Access Override")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sat, 21 Oct 2017 08:50:18 +0000 (10:50 +0200)]
serial: omap: Fix EFR write on RTS deassertion
commit
2a71de2f7366fb1aec632116d0549ec56d6a3940 upstream.
Commit
348f9bb31c56 ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.
Fixes:
348f9bb31c56 ("serial: omap: Fix RTS handling")
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roberto Sassu [Tue, 7 Nov 2017 10:37:07 +0000 (11:37 +0100)]
ima: do not update security.ima if appraisal status is not INTEGRITY_PASS
commit
020aae3ee58c1af0e7ffc4e2cc9fe4dc630338cb upstream.
Commit
b65a9cfc2c38 ("Untangling ima mess, part 2: deal with counters")
moved the call of ima_file_check() from may_open() to do_filp_open() at a
point where the file descriptor is already opened.
This breaks the assumption made by IMA that file descriptors being closed
belong to files whose access was granted by ima_file_check(). The
consequence is that security.ima and security.evm are updated with good
values, regardless of the current appraisal status.
For example, if a file does not have security.ima, IMA will create it after
opening the file for writing, even if access is denied. Access to the file
will be allowed afterwards.
Avoid this issue by checking the appraisal status before updating
security.ima.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric W. Biederman [Thu, 16 Nov 2017 04:17:48 +0000 (22:17 -0600)]
net/sctp: Always set scope_id in sctp_inet6_skb_msgname
[ Upstream commit
7c8a61d9ee1df0fb4747879fa67a99614eb62fec ]
Alexandar Potapenko while testing the kernel with KMSAN and syzkaller
discovered that in some configurations sctp would leak 4 bytes of
kernel stack.
Working with his reproducer I discovered that those 4 bytes that
are leaked is the scope id of an ipv6 address returned by recvmsg.
With a little code inspection and a shrewd guess I discovered that
sctp_inet6_skb_msgname only initializes the scope_id field for link
local ipv6 addresses to the interface index the link local address
pertains to instead of initializing the scope_id field for all ipv6
addresses.
That is almost reasonable as scope_id's are meaniningful only for link
local addresses. Set the scope_id in all other cases to 0 which is
not a valid interface index to make it clear there is nothing useful
in the scope_id field.
There should be no danger of breaking userspace as the stack leak
guaranteed that previously meaningless random data was being returned.
Fixes:
372f525b495c ("SCTP: Resync with LKSCTP tree.")
History-tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huacai Chen [Thu, 16 Nov 2017 03:07:15 +0000 (11:07 +0800)]
fealnx: Fix building error on MIPS
[ Upstream commit
cc54c1d32e6a4bb3f116721abf900513173e4d02 ]
This patch try to fix the building error on MIPS. The reason is MIPS
has already defined the LONG macro, which conflicts with the LONG enum
in drivers/net/ethernet/fealnx.c.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin Long [Tue, 17 Oct 2017 15:26:10 +0000 (23:26 +0800)]
sctp: do not peel off an assoc from one netns to another one
[ Upstream commit
df80cd9b28b9ebaa284a41df611dbf3a2d05ca74 ]
Now when peeling off an association to the sock in another netns, all
transports in this assoc are not to be rehashed and keep use the old
key in hashtable.
As a transport uses sk->net as the hash key to insert into hashtable,
it would miss removing these transports from hashtable due to the new
netns when closing the sock and all transports are being freeed, then
later an use-after-free issue could be caused when looking up an asoc
and dereferencing those transports.
This is a very old issue since very beginning, ChunYu found it with
syzkaller fuzz testing with this series:
socket$inet6_sctp()
bind$inet6()
sendto$inet6()
unshare(0x40000000)
getsockopt$inet_sctp6_SCTP_GET_ASSOC_ID_LIST()
getsockopt$inet_sctp6_SCTP_SOCKOPT_PEELOFF()
This patch is to block this call when peeling one assoc off from one
netns to another one, so that the netns of all transport would not
go out-sync with the key in hashtable.
Note that this patch didn't fix it by rehashing transports, as it's
difficult to handle the situation when the tuple is already in use
in the new netns. Besides, no one would like to peel off one assoc
to another netns, considering ipaddrs, ifaces, etc. are usually
different.
Reported-by: ChunYu Wang <chunwang@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason A. Donenfeld [Thu, 9 Nov 2017 04:04:44 +0000 (13:04 +0900)]
af_netlink: ensure that NLMSG_DONE never fails in dumps
[ Upstream commit
0642840b8bb008528dbdf929cec9f65ac4231ad0 ]
The way people generally use netlink_dump is that they fill in the skb
as much as possible, breaking when nla_put returns an error. Then, they
get called again and start filling out the next skb, and again, and so
forth. The mechanism at work here is the ability for the iterative
dumping function to detect when the skb is filled up and not fill it
past the brim, waiting for a fresh skb for the rest of the data.
However, if the attributes are small and nicely packed, it is possible
that a dump callback function successfully fills in attributes until the
skb is of size 4080 (libmnl's default page-sized receive buffer size).
The dump function completes, satisfied, and then, if it happens to be
that this is actually the last skb, and no further ones are to be sent,
then netlink_dump will add on the NLMSG_DONE part:
nlh = nlmsg_put_answer(skb, cb, NLMSG_DONE, sizeof(len), NLM_F_MULTI);
It is very important that netlink_dump does this, of course. However, in
this example, that call to nlmsg_put_answer will fail, because the
previous filling by the dump function did not leave it enough room. And
how could it possibly have done so? All of the nla_put variety of
functions simply check to see if the skb has enough tailroom,
independent of the context it is in.
In order to keep the important assumptions of all netlink dump users, it
is therefore important to give them an skb that has this end part of the
tail already reserved, so that the call to nlmsg_put_answer does not
fail. Otherwise, library authors are forced to find some bizarre sized
receive buffer that has a large modulo relative to the common sizes of
messages received, which is ugly and buggy.
This patch thus saves the NLMSG_DONE for an additional message, for the
case that things are dangerously close to the brim. This requires
keeping track of the errno from ->dump() across calls.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cong Wang [Fri, 10 Nov 2017 00:43:13 +0000 (16:43 -0800)]
vlan: fix a use-after-free in vlan_device_event()
[ Upstream commit
052d41c01b3a2e3371d66de569717353af489d63 ]
After refcnt reaches zero, vlan_vid_del() could free
dev->vlan_info via RCU:
RCU_INIT_POINTER(dev->vlan_info, NULL);
call_rcu(&vlan_info->rcu, vlan_info_rcu_free);
However, the pointer 'grp' still points to that memory
since it is set before vlan_vid_del():
vlan_info = rtnl_dereference(dev->vlan_info);
if (!vlan_info)
goto out;
grp = &vlan_info->grp;
Depends on when that RCU callback is scheduled, we could
trigger a use-after-free in vlan_group_for_each_dev()
right following this vlan_vid_del().
Fix it by moving vlan_vid_del() before setting grp. This
is also symmetric to the vlan_vid_add() we call in
vlan_device_event().
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes:
efc73f4bbc23 ("net: Fix memory leak - vlan_info struct")
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>