drm/amdgpu/display/dc: add FBC to dc_config

Add FBC to the list of features that can be enabled from the DM.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add DC feature mask module parameter

Similar to ppfeaturemask.  Allows you to selectively enable/disable
DC features.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/display: check if fbc is available in set_static_screen_control (v2)

The value is dependent on whether fbc is available.

v2: only check if num_pipes is valid

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: disable page queue on Vega10 SR-IOV VF

Currently, SDMA page queue is not used under SR-IOV VF, and this queue will
cause ring test failure in amdgpu module reload case. So just disable it.

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: set Vega20 LBPW as disabled at default

For Vega20, LBPW feature is disabled at default.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: always use fast UCLK switching when UCLK DPM enabled

With UCLK DPM enabled, slow switching is not supported any more.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: set a default fclk/gfxclk ratio

Otherwise big gap between these two clocks may causes
some hangs.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: Fix bo_global and mem_global kfree error

ttm_bo_glob and ttm_mem_glob are defined as structure instance, while
not allocated by kzalloc, so kfree should not be invoked to release
them anymore. Otherwise, it will cause the following kernel BUG when
unloading amdgpu module

[   48.419294] kernel BUG at /build/linux-5s7Xkn/linux-4.15.0/mm/slub.c:3894!
[   48.419352] invalid opcode: 0000 [#1] SMP PTI
[   48.419387] Modules linked in: amdgpu(OE-) amdchash(OE) amdttm(OE) amd_sched(OE) amdkcl(OE) amd_iommu_v2 drm_kms_helper drm i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi pcbc snd_seq snd_seq_device snd_timer aesni_intel snd soundcore joydev aes_x86_64 crypto_simd glue_helper cryptd input_leds mac_hid serio_raw binfmt_misc nfsd auth_rpcgss nfs_acl lockd grace sunrpc sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4 8139too psmouse i2c_piix4 8139cp mii floppy pata_acpi
[   48.419782] CPU: 1 PID: 1281 Comm: modprobe Tainted: G           OE    4.15.0-20-generic #21-Ubuntu
[   48.419838] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[   48.419901] RIP: 0010:kfree+0x137/0x180
[   48.419934] RSP: 0018:ffffb02101273bf8 EFLAGS: 00010246
[   48.419974] RAX: ffffeee1418ad7e0 RBX: ffffffffc075f100 RCX: ffff8fed7fca7ed0
[   48.420025] RDX: 0000000000000000 RSI: 000000000003440e RDI: 0000000022400000
[   48.420073] RBP: ffffb02101273c10 R08: 0000000000000010 R09: ffff8fed7ffd3680
[   48.420121] R10: ffffeee1418ad7c0 R11: ffff8fed7ffd3000 R12: ffffffffc075e2c0
[   48.420169] R13: ffffffffc074ec10 R14: ffff8fed73063900 R15: ffff8fed737428e8
[   48.420216] FS:  00007fdc912ec540(0000) GS:ffff8fed7fc80000(0000) knlGS:0000000000000000
[   48.420267] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   48.420308] CR2: 000055fa40c30060 CR3: 000000023470a006 CR4: 00000000003606e0
[   48.420358] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   48.420405] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   48.420452] Call Trace:
[   48.420485]  ttm_bo_global_kobj_release+0x20/0x30 [amdttm]
[   48.420528]  kobject_release+0x6a/0x180
[   48.420562]  kobject_put+0x28/0x50
[   48.420595]  ttm_bo_global_release+0x36/0x50 [amdttm]
[   48.420636]  amdttm_bo_device_release+0x119/0x180 [amdttm]
[   48.420678]  ? amdttm_bo_clean_mm+0xa6/0xf0 [amdttm]
[   48.420760]  amdgpu_ttm_fini+0xc9/0x180 [amdgpu]
[   48.420821]  amdgpu_bo_fini+0x12/0x40 [amdgpu]
[   48.420889]  gmc_v9_0_sw_fini+0x40/0x50 [amdgpu]
[   48.420947]  amdgpu_device_fini+0x36f/0x4c0 [amdgpu]
[   48.421007]  amdgpu_driver_unload_kms+0xb4/0x150 [amdgpu]
[   48.421058]  drm_dev_unregister+0x46/0xf0 [drm]
[   48.421102]  drm_dev_unplug+0x12/0x70 [drm]

Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu/dm: Fix dm_dp_create_fake_mst_encoder()

[why]
Removing connector reusage from DM to match the rest of the tree ended
up revealing an issue that was surprisingly subtle. The original amdgpu
code for DC that was submitted appears to have left a chunk in
dm_dp_create_fake_mst_encoder() that tries to find a "master encoder",
the likes of which isn't actually used or stored anywhere. It does so at
the wrong time as well by trying to access parts of the drm_connector
from the encoder init before it's actually been initialized. This
results in a NULL pointer deref on MST hotplugs:

[  160.696613] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[  160.697234] PGD 0 P4D 0
[  160.697814] Oops: 0010 [#1] SMP PTI
[  160.698430] CPU: 2 PID: 64 Comm: kworker/2:1 Kdump: loaded Tainted: G           O      4.19.0Lyude-Test+ #2
[  160.699020] Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.22 05/17/2018
[  160.699672] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[  160.700322] RIP: 0010:          (null)
[  160.700920] Code: Bad RIP value.
[  160.701541] RSP: 0018:ffffc9000029fc78 EFLAGS: 00010206
[  160.702183] RAX: 0000000000000000 RBX: ffff8804440ed468 RCX: ffff8804440e9158
[  160.702778] RDX: 0000000000000000 RSI: ffff8804556c5700 RDI: ffff8804440ed000
[  160.703408] RBP: ffff880458e21800 R08: 0000000000000002 R09: 000000005fca0a25
[  160.704002] R10: ffff88045a077a3d R11: ffff88045a077a3c R12: ffff8804440ed000
[  160.704614] R13: ffff880458e21800 R14: ffff8804440e9000 R15: ffff8804440e9000
[  160.705260] FS:  0000000000000000(0000) GS:ffff88045f280000(0000) knlGS:0000000000000000
[  160.705854] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  160.706478] CR2: ffffffffffffffd6 CR3: 000000000200a001 CR4: 00000000003606e0
[  160.707124] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  160.707724] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  160.708372] Call Trace:
[  160.708998]  ? dm_dp_add_mst_connector+0xed/0x1d0 [amdgpu]
[  160.709625]  ? drm_dp_add_port+0x2fa/0x470 [drm_kms_helper]
[  160.710284]  ? wake_up_q+0x54/0x70
[  160.710877]  ? __mutex_unlock_slowpath.isra.18+0xb3/0x110
[  160.711512]  ? drm_dp_dpcd_access+0xe7/0x110 [drm_kms_helper]
[  160.712161]  ? drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
[  160.712762]  ? drm_dp_check_and_send_link_address+0xa3/0xd0 [drm_kms_helper]
[  160.713408]  ? drm_dp_mst_link_probe_work+0x4b/0x80 [drm_kms_helper]
[  160.714013]  ? process_one_work+0x1a1/0x3a0
[  160.714667]  ? worker_thread+0x30/0x380
[  160.715326]  ? wq_update_unbound_numa+0x10/0x10
[  160.715939]  ? kthread+0x112/0x130
[  160.716591]  ? kthread_create_worker_on_cpu+0x70/0x70
[  160.717262]  ? ret_from_fork+0x35/0x40
[  160.717886] Modules linked in: amdgpu(O) vfat fat snd_hda_codec_generic joydev i915 chash gpu_sched ttm i2c_algo_bit drm_kms_helper snd_hda_codec_hdmi hp_wmi syscopyarea iTCO_wdt sysfillrect sparse_keymap sysimgblt fb_sys_fops snd_hda_intel usbhid wmi_bmof drm snd_hda_codec btusb snd_hda_core intel_rapl btrtl x86_pkg_temp_thermal btbcm btintel coretemp snd_pcm crc32_pclmul bluetooth psmouse snd_timer snd pcspkr i2c_i801 mei_me i2c_core soundcore mei tpm_tis wmi tpm_tis_core hp_accel ecdh_generic lis3lv02d tpm video rfkill acpi_pad input_polldev hp_wireless pcc_cpufreq crc32c_intel serio_raw tg3 xhci_pci xhci_hcd [last unloaded: amdgpu]
[  160.720141] CR2: 0000000000000000

Somehow the connector reusage DM was using for MST connectors managed to
paper over this issue entirely; hence why this was never caught until
now.

[how]
Since this code isn't used anywhere and seems useless anyway, we can
just drop it entirely. This appears to fix the issue on my HP ZBook with
an AMD WX4150.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Drop reusing drm connector for MST

[why]
It is not safe to keep existing connector while entire topology
has been removed. Could lead potential impact to uapi.
Entirely unregister all the connectors on the topology,
and use a new set of connectors when the topology is plugged back
on.

[How]
Remove the drm connector entirely each time when the
corresponding MST topology is gone.
When hotunplug a connector (e.g., DP2)
1. Remove connector from userspace.
2. Drop it's reference.
When hotplug back on:
1. Detect new topology, and create new connectors.
2. Notify userspace with sysfs hotplug event.
3. Reprobe new connectors, and reassign CRTC from old (e.g., DP2)
to new (e.g., DP3) connector.

Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Cleanup MST non-atomic code workaround

[why]
It is not correct to touch aconnector within atomic_check.

[How]
It was added as workaround before, and no longer needed.

Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix frame size of amdgpu_xgmi_add_devices excceed 1024 bytes

Instead of stack-allocated psp_xgmi_topology_info in function
amdgpu_xgmi_add_device, dynamically allocated this structure to
avoid the frame size of this function excceed 1024 bytes

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add set_topology_info function

set_topology_info is used for driver to set current topology info
to xgmi ta

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add get_topology_info function

get_topology_info function is used for driver to query topology_info
for current device from xgmi ta

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: update topology info structures

topology info structure needs to match with the one defined
in xgmi ta

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add get_hive_id function

get_hive_id is used for driver to query hive_id for current device
from xgmi ta

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add get_node_id function

get_node_id function is used for driver to get node_id
for current device from xgmi ta

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: initialize xgmi session (v2)

Setup and tear down xgmi as part of psp.

v2:
- make psp_xgmi_terminate static
- squash in:
drm/amdgpu: only issue xgmi cmd when it is enabled
drm/amdgpu/psp: terminate xgmi ta in suspend and hw_fini phase

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add helper function to invoke xgmi ta per ta cmd_id

psp_xgmi_invoke is the helper function to issue ta cmd to firmware

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add xgmi ta header

Add the psp xgmi driver interface.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add helper function to load/unload xgmi ta

Add helper functions for the psp xgmi ta.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: init/de-init xgmi ta microcode

Add ucode handling for psp xgmi ta firmware.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/psp: add structure for xgmi ta and its shared buffer

Add data structures for xgmi trusted application.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vega20: add CLK base offset

In case we need to access CLK registers.

Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Stop leaking planes

[Why]
drm_plane_cleanup does not free the plane.

[How]
Call drm_primary_helper_destroy which will also free the plane.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Drop amdgpu_plane

It's unnecessarily duplicating drm_plane_type.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix misleading buffer information

RETIMER_REDRIVER_INFO shows the buffer as a decimal value with a '0x'
prefix, which is somewhat misleading.

Fix it to print hexadecimal, as was intended.

Fixes: 2f14bc89("drm/amd/display: add retimer log for HWQ tuning use.")
Cc: Charlene Liu <charlene.liu@amd.com>
Cc: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: Don't fail on backlight = 0

Amgpu's backlight update status function was
returning 1 (an error value) when the backlight
property was 0.  This breaks users that assume
0 is a valid backlight value (which is a
correct assumption)

If the user passes in a backlight value of 0,
tell them everything is fine, then write a value of
1 to hardware.

Signed-off-by: David Francis <David.Francis@amd.com>
Bugzilla: https://bugs.freedesktop.org/108668
Fixes: 416615ea9578 ("drm/amd/display: set backlight level limit to 1")
Cc: Suresh.Guttula@amd.com
Cc: Harry.Wentland@amd.com
Cc: Samantham@posteo.net
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: Update atom_smu_info_v3_3 structure

Mainly adding the WAFL spread spectrum info, for adjusting display
clocks when XGMI is enabled.

Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use GMC v9 KIQ workaround only for the GFXHUB

The MMHUB is not affected by this.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: drop the busy wait for GMC v9 TLB invalidations

This code is not performance critical.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup GMC v9 TLB invalidation

Move the kiq handling into amdgpu_virt.c and drop the fallback.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: remove nonsense in_interrupt() checks

might_sleep() is supposed to raise if warning if called in interrupt or
atomic context.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

uapi: fix more linux/kfd_ioctl.h userspace compilation errors

Consistently use types provided by <linux/types.h> via <drm/drm.h>
to fix struct kfd_ioctl_get_queue_wave_state_args userspace compilation errors.

Fixes: 5df099e8bc83f ("drm/amdkfd: Add wavefront context save state retrieval ioctl")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

uapi: fix linux/kfd_ioctl.h userspace compilation errors

Consistently use types provided by <linux/types.h> via <drm/drm.h>
to fix the following linux/kfd_ioctl.h userspace compilation errors:

/usr/include/linux/kfd_ioctl.h:250:2: error: unknown type name 'uint32_t'
  uint32_t reset_type;
/usr/include/linux/kfd_ioctl.h:251:2: error: unknown type name 'uint32_t'
  uint32_t reset_cause;
/usr/include/linux/kfd_ioctl.h:252:2: error: unknown type name 'uint32_t'
  uint32_t memory_lost;
/usr/include/linux/kfd_ioctl.h:253:2: error: unknown type name 'uint32_t'
  uint32_t gpu_id;

Fixes: 0c119abad7f0d ("drm/amd: Add kfd ioctl defines for hw_exception event")
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: fix interrupt spin lock

Vega10 has multiple interrupt rings, so this can be called from multiple
calles at the same time resulting in:

[   71.779334] ================================
[   71.779406] WARNING: inconsistent lock state
[   71.779478] 4.19.0-rc1+ #44 Tainted: G        W
[   71.779565] --------------------------------
[   71.779637] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[   71.779740] kworker/6:1/120 [HC0[0]:SC0[0]:HE1:SE1] takes:
[   71.779832] 00000000ad761971 (&(&kfd->interrupt_lock)->rlock){?...},
at: kgd2kfd_interrupt+0x75/0x100 [amdgpu]
[   71.780058] {IN-HARDIRQ-W} state was registered at:
[   71.780115]   _raw_spin_lock+0x2c/0x40
[   71.780180]   kgd2kfd_interrupt+0x75/0x100 [amdgpu]
[   71.780248]   amdgpu_irq_callback+0x6c/0x150 [amdgpu]
[   71.780315]   amdgpu_ih_process+0x88/0x100 [amdgpu]
[   71.780380]   amdgpu_irq_handler+0x20/0x40 [amdgpu]
[   71.780409]   __handle_irq_event_percpu+0x49/0x2a0
[   71.780436]   handle_irq_event_percpu+0x30/0x70
[   71.780461]   handle_irq_event+0x37/0x60
[   71.780484]   handle_edge_irq+0x83/0x1b0
[   71.780506]   handle_irq+0x1f/0x30
[   71.780526]   do_IRQ+0x53/0x110
[   71.780544]   ret_from_intr+0x0/0x22
[   71.780566]   cpuidle_enter_state+0xaa/0x330
[   71.780591]   do_idle+0x203/0x280
[   71.780610]   cpu_startup_entry+0x6f/0x80
[   71.780634]   start_secondary+0x1b0/0x200
[   71.780657]   secondary_startup_64+0xa4/0xb0

Fix this by always using irq save spin locks.

Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Add helper function to get sdma index

Get the sdma index from ring

v2: refine function name

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Flora Cui <flora.cui@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Refine function name

there is no functional changes.just
refine function name to keep
consistence with other files.

change amdgpu_get_sdma_instance to
amdgpu_sdma_get_instance_from_ring.
suggested by alex.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Flora Cui <flora.cui@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: do the comparison in the right Khz granularity

Convert the operands on the two sides into the same granularity.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Modify the argument of emit_ib interface

use the point of struct amdgpu_job as the function
argument instand of vmid, so the other members of
struct amdgpu_job can be visit in emit_ib function.

v2: add a wrapper for getting the VMID
    add the job before the ib on the parameter list.
v3: refine the wrapper name

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Change AMDGPU_CSA_SIZE to 128K

In order to support new asics and MCBP feature
enablement on baremetal.

Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Move csa related code to separate file

In baremetal, also need to reserve csa for preemption.
so move the csa related code out of sriov.

Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Refine CSA related functions

There is no functional changes,
Use function arguments for SRIOV special variables which
is hardcode in those functions.

so we can share those functions in baremetal.

Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Remove useless csa gpu address in vmid0

driver didn't use this address so far.

Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix gfx wptr for sdma v4

The wptr value will be shitfed when function returns.
Remove the redundant shift and clean up.

Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: disable page queue on SDMA for Vega12

It blocks most of sanity tests, so disable it for now.

Tested-by: Chen Gong <Curry.Gong@amd.com>
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: update smu firmware images for VI variants (v2)

Some new variants require updated firmware.

V2: add MODULE_FIRMWARE for new firmwares

Reviewed-by: Huang Rui <ray.huang@amd.com> (v1)
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add condition to sync eDP SW status and HW status

[Why]
Need to disable EDP backlight when enter S4 with EDP only
and resume from S4 with secondary only.

[How]
Align the real hw and sw state via vBios scratch register in
function enable_accelerated_mode when resume from S4.

Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove the check to see if pp_display_cfg is changed

[Why]
When going to full-screen mode commit_planes_for_stream tries to decrease
dcf_deep_sleep value, but safe_to_lower is false, so we don't send the new value
to SMU but dc context gets updated.
Later when dc_post_update_surfaces_to_stream tries to lower dcf_ds when
safe_to_lower is true, this check prevents the message from being sent.

[How]
Remove the check that compares new value with what is stored in dc_context.
This check is not necessary as dcn1_update_clocks already checks if the value
is different from the current dcf_dp value.

Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove CRTC_3D_STRUCTURE_V_UPDATE_MODE bit programming.

[Description]
This is based on HW programming guide update.

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Expose target backlight level

[Why]
DM may want to understand any backlight optimizations
applied, so DM needs a way to query from the HW both
the real current backlight, which may be value during
transition.
And also target backlight, which may be after some
backlight optimizations applied.

[How]
Add interface to query current and target backlight levels
Target level may indicate backlight level after backlight
optimization and reductions are applied.

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Guard against null stream_state in set_crc_source

[Why]

The igt@kms_plane@pixel-format-pipe tests can create a sequence where
stream_state is NULL during amdgpu_dm_crtc_set_crc_source which results
in a null pointer dereference.

[How]

Guard against stream_state being NULL before accessing its fields. This
doesn't fix the root cause of the issue so a DRM_ERROR is generated
to still fail the tests.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix mirror rotation scaling math

Curretly dc will incorrectly calculate viewport when there is
rotation or mirror being applied

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Su Chung <Su.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Retiring set_display_requirements in dm_pp_smu.h - part4

[Why]
In DCN we want direct DC to SMU calls, with minimal interference from
pplib.
The reason for each pp_smu interface mapping to 1 SMU message is so we
can have the sequencing of different SMU message in DC and shared across
different OS's.
This will also simplify debugging as DAL owns this interaction and
there's no confusion about division of ownership.

[How]
Part 4: Change clock units so they match the values PPLib sends to SMU.

Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove program_csc_matrix

[Why] On DCN1/DCE, There are two functions programming OCSC:
program_csc_matrix and program_output_csc. They do the same thing.

[How] Consolidate to use only program_output_csc.

Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix some backlight variable styling

variableNamingsLikeSo aren't to convention. use_this_instead.

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Expand dc to use 16.16 bit backlight

[Why] We want to increase precision for backlight setting.
But DC interface takes 8 bit backlight level value only.

[How] DMCU already takes 16 bit backlight level.
Expand the DC interface to take 16.16 bit value.
Max 32 bit backlight value (0xFFFF) will represent
max backlight (100%)

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove some old TODO's

They are no longer relevant

Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Initial documentation for AMDgpu DC

[Why]
Documentation is helpful for the community to understand our code.
This change does some high-level documentation of some DM interfaces
with DRM, and the amdgpu base driver.

[How]
An entry for AMDgpu DC has been added to Documentation/gpu/drivers.rst
TOC. amdgpu-dc.rst is created to pull in inline doc-strings, which:
- Provides an overview for "What is DM?"
- Documents AMDgpu DM lifecyle
- Documents IRQ management
- Documents atomic_check and commit_tail interfaces

Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix potential nullptr error

[Why]
Fix surface/plane potential nullptr

[How]
add null check

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.04

Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix up coverity issues

[Why]
Coverity found various high-impact issues that need resolving.

[How]
Fix  some buffer overruns and uninitialized variables.

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove interlace scaling adjustment

We do not need to adjust surface scaling when p2i is enabled
and we do not support interlaced timing otherwise

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add missing pipes registers for VGA enable/disable

Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix dml max voltage state

Gabe's formula sometimes uses values from non-existent 'unsupported'
state to do validation.

This change adds this extra state so validation can work correctly.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Clip all remaining regamma points after first clipped point

[Why]
All values computed in the gamma curve after the first upperbound
clipped point will need to be clipped anyways. We can avoid
unnecessary computations and potential fixed point
overflow by instead clipping these values to 1 automatically.

[How]
Track if upper-bound clipping has been done, and clip all values after
this threshold is reached without computing the output gamma
point.

Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.03

Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set gamma not working on MPO planes

[Why]
Set gamma not working on certain planes in MPO configuration
Root cause is that video format (YUV-420) isn't allowed for IGAM where
gamma is applied.
Fix is not easy though:
1. allowing will not work because IGAM is before ICSC so RGB gamma would
be applied on YUV pixels.
2. Moving OS gamma to DGAM or RGAM resulted in weird artifacts.

Ultimately the root cause for these artifacts was due to handling end
points and the fact that YUV->RGB conversion will frequently "overshoot"
FP 1.0 value. DCE  has a single end point and slope, so we would take max.
In nightlight mode, blue channel is reduced, sometimes to flat 0 line,
but red is virtually unchanged. Any "overshot" in blue will be clipped
to 1 (max R,G,B) instead of max blue value.

[How]
Fortunately, this can be fixed on DCN where we have end point and slope
for all three color channels. We cannot fix this problem on DCE.

Other things fixed:
- switch (back) to using RGAM for OS gamma instead of IGAM
- add coeffs for 709 YUV->RGB (we used RGB->YUV for both conversions)
- switch color temperature method to scaled bradford - otherwise we would
have clipping problems that caused us to switch to IGAM for OS gamma
in the first place.
- comments and some minor improvements - there are some more issues but
they will be addressed in separate commits.

Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: drop the remaining uses of ring idx in messages

Consistently use the ring name instead.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup si_dma_ring_test_ib

Accidentially missed during the last cleanup.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup uvd_v6_0_ring_test_ring

Accidentially missed during the last cleanup.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use ring name instead of idx in traces

Further remove using the ring index in messages and traces.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: print an error when the parser can't be initialized

Similar to other error messages, might help for tracking down
issues.

Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/scheduler: Add drm_sched_job_cleanup

This patch adds a new API to clean up the scheduler job resources. This
is primarliy needed in cases the job was created but was not queued to
the scheduler queue. Additionally with this change, the layer which
creates the scheduler job also gets to free up the job's resources and
this entails moving the dma_fence_put(finished_fence) to the drivers
ops free handler routines.

Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: remove messages from IB tests

We already print an error message that an IB test failed in the common
code.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup skipping IB test on KIQ

Instead of hard coding the ring type in the function just never provide
a test_ib callback.

Additional to that remove the emit_ib callback to make sure the nobody
ever tries to execute an IB on the KIQ.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup amdgpu_ib_ring_tests

Test only initialized rings, use the ring name instead of the index in the
error message and note on which device the error occured.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: further ring test cleanups

Move all error messages from IP specific code into the common helper.
This way we now uses the ring name in the messages instead of the index
and note which device is affected as well.

Also cleanup error handling in the IP specific code and consequently use
ETIMEDOUT when the ring test timed out.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/amdkfd: clean up mmhub and gfxhub includes

Use the appropriate mmhub and gfxhub headers rather than adding
them to the gmc9 header.

Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Enable default GPU reset for dGPU on gfx8/9 v3

After testing looks like these subset of ASICs has GPU reset
working for the most part. Enable reset due to job timeout.

v2: Switch from GFX version to ASIC type.
v3: Fix identation

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Retire amdgpu_ring.ready flag v4

Start using drm_gpu_scheduler.ready isntead.

v3:
Add helper function to run ring test and set
sched.ready flag status accordingly, clean explicit
sched.ready sets from the IP specific files.

v4: Add kerneldoc and rebase.

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/sched: Add boolean to mark if sched is ready to work v5

Problem:
A particular scheduler may become unsuable (underlying HW) after
some event (e.g. GPU reset). If it's later chosen by
the get free sched. policy a command will fail to be
submitted.

Fix:
Add a driver specific callback to report the sched status so
rq with bad sched can be avoided in favor of working one or
none in which case job init will fail.

v2: Switch from driver callback to flag in scheduler.

v3: rebase

v4: Remove ready paramter from drm_sched_init, set
uncoditionally to true once init done.

v5: fix missed change in v3d in v4 (Alex)

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm: Remove drm_global.{c,h} v2

The content of drm_global.{c,h} is obsolete.

v2: rebase on dropping TTM functionality

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: initialize globals during device init (v2)

Make sure that the global BO state is always correctly initialized.

This allows removing all the device code to initialize it.

v2: fix up vbox (Alex)

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: use a static ttm_bo_global instance

As the name says we only need one global instance of ttm_bo_global.

Just use a single exported instance which is save to initialize multiple times.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: make the device list mutex static

This way it can protect the whole BO global state.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: use a static ttm_mem_global instance

As the name says we only need one global instance of ttm_mem_global.

Drop all the driver initialization and just use a single exported
instance which is initialized during BO global initialization.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: remove duplicated includes

Remove some duplicated include.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/kms: remove set but not used variable 'pll'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/radeon/radeon_legacy_tv.c: In function 'radeon_legacy_tv_init_restarts':
drivers/gpu/drm/radeon/radeon_legacy_tv.c:435:21: warning:
 variable 'pll' set but not used [-Wunused-but-set-variable]
  struct radeon_pll *pll;

It never used since introduction in commit
4ce001abafaf ("drm/radeon/kms: add initial radeon tv-out support.")
Also remove related variables 'dev, rdev, radeon_crtc'

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Added a few comments for gart

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Use functions from amdgpu to invalidate vmid in kfd

As part of the change, we stop taking the srbm lock, and start to use
the same invalidation engine and software lock as amdgpu.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Reorganize amdgpu_gmc_flush_gpu_tlb() for kfd to use

Add a flush_type parameter to that series of functions.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Remove unnecessary register setting when invalidating tlb in kfd

Those register settings have been done in gfxhub_v1_0_program_invalidation()
and mmhub_v1_0_program_invalidation().

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: page_table_base already have the flags needed

The flags are added when calling amdgpu_gmc_pd_addr().

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Delete a duplicate statement in set_pasid_vmid_mapping()

The same statement is later done in kgd_set_pasid_vmid_mapping(), so no
need to do it in set_pasid_vmid_mapping().

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Add DCC flags for GFX9 amdgpu_bo

[Why]
Hardware support for Delta Color Compression (DCC) decompression is
available in DC for GFX9 but there's no way for userspace to enable
the feature.

Enabling the feature can provide improved GFX performance and
power savings in many situations.

[How]
Extend the GFX9 tiling flags to include DCC parameters. These are
logically grouped together with tiling flags even if they are
technically distinct.

This trivially maintains backwards compatibility with existing
users of amdgpu_gem_metadata. No new IOCTls or data structures are
needed to support DCC.

This patch helps expose DCC attributes to both libdrm and amdgpu_dm.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Check if hubp function hooks exist before calling them

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Retiring set_display_requirements in dm_pp_smu.h - part3

[Why]
In DCN we want direct DAL to SMU calls, with as little as
possible interference by pplib. The reason for each pp_smu interface
mapping to 1 SMU message is so we can have the sequencing of different
SMU message in dal and shared across different OS. This will also
simplify debugging as DAL owns this interaction and there's no
confusion about division of ownership.

[How]
Separate the set_hard_min_fclk_by_freq message from the
SMU messages that are sent as part of pp_rv_set_display_requirement.
directly notify min dcfclk to smu part 2

Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove stream_res tg null check in commit planes

[Why]
TG in pipe_ctx stream resource is not null where used in
commit_planes_do_stream_update since it is assigned the
same time the stream is set in pipe_ctx - when the pipe is
acquired. This null check produced a static code analysis
warning and should be removed to avoid similar unnecessary
checks in the future.

[How]
Remove the null check.

Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Reverse the sequence of ctx_mgr_fini
and vm_fini in amdgpu_driver_postclose_kms

csa buffer will be created per ctx, when ctx fini,
the csa buffer and va will be released. so need to
do ctx_mgr fin before vm fini.

Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>