OSDN Git Service
Atsushi Nemoto [Fri, 22 Jun 2007 14:22:06 +0000 (23:22 +0900)]
[MIPS] rbtx4938: Convert SPI codes to use generic SPI drivers
Use rtc-rs5c348 and at25 spi protocol driver and spi_txx9 spi
controller driver instead of platform dependent codes.
This patch also removes dependencies to old RTC interfaces such as
rtc_mips_get_time, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Fri, 22 Jun 2007 14:21:55 +0000 (23:21 +0900)]
[MIPS] rbtx4938: Add generic GPIO support
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thomas Bogendoerfer [Wed, 20 Jun 2007 21:36:47 +0000 (23:36 +0200)]
[MIPS] SNI RM updates
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Marc St-Jean [Thu, 14 Jun 2007 21:57:11 +0000 (15:57 -0600)]
[MIPS] PMC MSP71xx default configuration
Patch to add default configuration for the PMC-Sierra
MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Marc St-Jean [Thu, 14 Jun 2007 21:56:23 +0000 (15:56 -0600)]
[MIPS] PMC MSP71xx PCI support
Patch to add PCI support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Marc St-Jean [Thu, 14 Jun 2007 21:55:31 +0000 (15:55 -0600)]
[MIPS] PMC MSP71xx mips common
Patch to add mips common support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Marc St-Jean [Thu, 14 Jun 2007 21:54:47 +0000 (15:54 -0600)]
[MIPS] PMC MSP71xx core platform
Patch to add core platform support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adrian Bunk [Tue, 19 Jun 2007 20:27:04 +0000 (22:27 +0200)]
[MIPS] Removes the few leftovers of the MOMENCO_JAGUAR_ATX removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Songmao Tian [Wed, 6 Jun 2007 06:52:38 +0000 (14:52 +0800)]
[MIPS] New files for lemote fulong mini-PC support
Signed-off-by: Fuxin Zhang <zhangfx@lemote.com>
Signed-off-by: Songmao Tian <tiansm@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fuxin Zhang [Wed, 6 Jun 2007 06:52:43 +0000 (14:52 +0800)]
[MIPS] define Hit_Invalidate_I to Index_Invalidate_I for loongson2
Signed-off-by: Fuxin Zhang <zhangfx@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:33:02 +0000 (17:33 +0100)]
[MIPS] Convert init_thread initialization to ISO C initializers.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:33:02 +0000 (17:33 +0100)]
[MIPS] Enable support for the userlocal hardware register
Which will cut down the cost of RDHWR $29 which is used to obtain the
TLS pointer and so far being emulated in software down to a single cycle
operation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:33:02 +0000 (17:33 +0100)]
[MIPS] FP affinity: Coding style cleanups
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:33:01 +0000 (17:33 +0100)]
[MIPS] Put an end to <asm/serial.h>'s long and annyoing existence
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 11 Jun 2007 13:08:55 +0000 (15:08 +0200)]
[MIPS] Remove Momenco Ocelot C support
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/configs/ocelot_c_defconfig
delete mode 100644 arch/mips/momentum/ocelot_c/Makefile
delete mode 100644 arch/mips/momentum/ocelot_c/cpci-irq.c
delete mode 100644 arch/mips/momentum/ocelot_c/dbg_io.c
delete mode 100644 arch/mips/momentum/ocelot_c/irq.c
delete mode 100644 arch/mips/momentum/ocelot_c/ocelot_c_fpga.h
delete mode 100644 arch/mips/momentum/ocelot_c/platform.c
delete mode 100644 arch/mips/momentum/ocelot_c/prom.c
delete mode 100644 arch/mips/momentum/ocelot_c/reset.c
delete mode 100644 arch/mips/momentum/ocelot_c/setup.c
delete mode 100644 arch/mips/momentum/ocelot_c/uart-irq.c
delete mode 100644 arch/mips/pci/fixup-ocelot-c.c
delete mode 100644 arch/mips/pci/pci-ocelot-c.c
Ralf Baechle [Tue, 10 Jul 2007 16:33:00 +0000 (17:33 +0100)]
[MIPS] IP32: Remove experimental tag from kconfig.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:33:00 +0000 (17:33 +0100)]
[MIPS] PCI: Make dev pointer argument of pcibios_map_irq const.
This is to break the code of people who think they are supposed to scribble
into the pci device structure - it's off limits.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Thu, 21 Jun 2007 06:06:21 +0000 (15:06 +0900)]
[MIPS] EV64120: Remove support
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Tue, 5 Jun 2007 10:45:07 +0000 (11:45 +0100)]
[MIPS] DECstation: Optimised early printk()
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maciej W. Rozycki [Tue, 29 May 2007 14:08:07 +0000 (15:08 +0100)]
[MIPS] No I/O ports on the DECstation
There are no I/O ports on the DECstation whatsoever in any configuration
as neither the CPU nor the peripheral buses used have a concept of such.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Mon, 4 Jun 2007 16:28:07 +0000 (01:28 +0900)]
[MIPS] Remove unused watchpoint support and arch/mips/lib-{32,64}
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Fri, 1 Jun 2007 17:12:41 +0000 (02:12 +0900)]
[MIPS] update cobalt_defconfig
Enable Cobalt button support and change ATA driver from BLK_DEV_VIA82CXXX
to PATA_VIA..
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:35 +0000 (17:46 +0200)]
[MIPS] Fix PHYS_OFFSET for 64-bits kernels with 32-bits symbols
The current implementation of __pa() for 64-bits kernels with 32-bits
symbols is broken. In this configuration, we need 2 values for
PAGE_OFFSET, one in XKPHYS and the other in CKSEG0 space.
When the value in CKSEG0 space is used, it doesn't take into account
of PHYS_OFFSET. Even worse we can't redefine this value.
The patch restores CPHYSADDR() but in __pa()'s implementation because
it removes the need of 2 PAGE_OFFSET.
OTOH, CPHYSADDR() is quite bad when dealing with mapped kernels. So
this patch assumes there's no need to deal with such kernel in 64-bits
world.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:34 +0000 (17:46 +0200)]
[MIPS] Move PHY_OFFSET definition in spaces.h
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:33 +0000 (17:46 +0200)]
[MIPS] Make PAGE_OFFSET aware of PHYS_OFFSET
For platforms that use PHYS_OFFSET and do not use a mapped kernel,
this patch automatically adds PHYS_OFFSET into PAGE_OFFSET.
Therefore there are no more needs for them to redefine PAGE_OFFSET.
For mapped kernel, they need to redefine PAGE_OFFSET anyways.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:32 +0000 (17:46 +0200)]
[MIPS] Clean up asm-mips/mach-generic/spaces.h
PAGE_OFFSET definition is now using CAC_BASE by default.
This patch also reorder some macros to make them appear
in the same order for both 32 and 64 bits configs.
It also makes use of const.h generic header file to
annotate constants.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 4 Jun 2007 15:46:31 +0000 (17:46 +0200)]
[MIPS] Allow generic spaces.h to be included by platform specific ones
Before this patch, when a platform needed to customize one constant in
spaces.h, they need to redefine all of them.
Now they can just redefine one constant and include the generic file
header at the end:
#include <asm/mach-generic/spaces.h>
This patch doesn't allow to redefine CAC_BASE, IO_BASE and UNCAC_BASE
for 32 bits platforms because there's no need to do so.
This will avoid some macro duplications. It's important specially if
we'll add complex macros.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 include/asm-mips/mach-ip32/spaces.h
Atsushi Nemoto [Fri, 1 Jun 2007 15:30:25 +0000 (00:30 +0900)]
[MIPS] Remove unused dump_tlb functions
Remove unused dump_tlb functions and cleanup some includes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Fri, 1 Jun 2007 15:21:30 +0000 (00:21 +0900)]
[MIPS] Unify dump_tlb
Unify lib-{32,64}/dump_tlb.c into lib/dump_tlb.c and move
lib-32/r3k_dump_tlb.c to lib directory.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:32:56 +0000 (17:32 +0100)]
[MIPS] MIPSsim: Move code away from the other MIPS Inc. BSP code.
It shares no code at all. While at it also fix up the beginning bitrot.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:32:56 +0000 (17:32 +0100)]
[MIPS] Hook for platforms to define cachability of /dev/mem regions
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:32:56 +0000 (17:32 +0100)]
[MIPS] Cleanup TO_PHYS_MASK definition
No point in adding yet another #ifdef for Loongson since all this mask is
being used for is converting an XKPHYS address into a physical address
anyway. So replace all definitions by one with the highest architectural
possible value.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Robert P. J. Day [Fri, 25 May 2007 18:32:28 +0000 (14:32 -0400)]
[MIPS] Transform old-style macros to newer "__noreturn"
Convert old/obsolete NORET_TYPE and ATTRIB_NORET macros to use the
newer standard of "__noreturn" as defined in compiler-gcc.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 10 Jul 2007 16:32:56 +0000 (17:32 +0100)]
[MIPS] SMTC: Use current_cpu_data instead of cpu_data[smp_processor_id]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Tue, 22 May 2007 19:44:42 +0000 (21:44 +0200)]
[MIPS] Add generic GPIO to Au1x00
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Fri, 22 Jun 2007 14:20:23 +0000 (23:20 +0900)]
[MIPS] Create fallback gpio.h
Create fallback gpio.h which only contains prototypes for gpio API.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Mon, 21 May 2007 15:05:58 +0000 (00:05 +0900)]
[MIPS] Add generic GPIO support
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adrian Bunk [Sat, 7 Jul 2007 01:03:27 +0000 (03:03 +0200)]
[MIPS] Remove unused cpu_callout_map and num_booting_cpus()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adrian Bunk [Sat, 7 Jul 2007 01:03:30 +0000 (03:03 +0200)]
[MIPS] "extern inline" -> "static inline"
"extern inline" will have different semantics with gcc 4.3, and
"static inline" is correct here.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Tue, 29 May 2007 15:38:07 +0000 (00:38 +0900)]
[MIPS] Simplify missing-syscalls for N32 and O32
Use standard missing-syscalls with EXTRA_CFLAGS instead of duplicating
the command. And move the archprepare rule before the archclean rule.
Suggested by Franck Bui-Huu. Also add "echo" to show the target ABI.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Mon, 28 May 2007 13:56:35 +0000 (22:56 +0900)]
[MIPS] Remove unused config entries
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Mon, 21 May 2007 14:00:38 +0000 (23:00 +0900)]
[MIPS] remove unused definitions for Cobalt
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Mon, 9 Jul 2007 22:50:56 +0000 (15:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (31 commits)
firewire: fw-sbp2: fix DMA mapping of management ORBs
firewire: fw-sbp2: fix DMA mapping of command ORBs
firewire: fw-sbp2: fix DMA mapping of S/G tables
firewire: fw-sbp2: add a boundary check
firewire: fw-sbp2: correctly align page tables
firewire: fw-sbp2: memset wants string.h
firewire: fw-sbp2: use correct speed in sbp2_agent_reset
firewire: fw-sbp2: correctly dereference by container_of
firewire: Document userspace ioctl interface.
firewire: fw-sbp2: implement nonexclusive login
firewire: fw-sbp2: let SCSI shutdown commands through before logout
firewire: fw-sbp2: implement max sectors limit for some old bridges
firewire: simplify a struct type
firewire: support S100B...S400B and link slower than PHY
firewire: optimize gap count with 1394b leaf nodes
firewire: remove unused macro
firewire: missing newline in printk
firewire: fw-sbp2: remove unused struct member
ieee1394: remove old isochronous ABI
ieee1394: sbp2: change some module parameters from int to bool
...
Linus Torvalds [Mon, 9 Jul 2007 22:50:31 +0000 (15:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: handle cases of volume knobs generating relative values
HID: Logitech keyboard 0xc311 needs reset leds quirk
HID: support for logitech cordless desktop LX500 special mapping
HID: fix autocentering of PID devices
HID: separate quirks for report descriptor fixup
HID: Add NOGET quirk for all NCR devices
HID: support for Petalynx Maxter remote control
HID: fix mismatch between hid-input HUT find/search mapping and the HUT
HID: support for Gameron dual psx adaptor
USB HID: avoid flush_scheduled_work()
HID: Use menuconfig objects
HID: force hid-input for Microsoft SideWinder GameVoice device
HID: input mapping for Chicony KU-0418 tactical pad
HID: make debugging output runtime-configurable
Linus Torvalds [Mon, 9 Jul 2007 22:26:43 +0000 (15:26 -0700)]
Merge branch 'upstream-linus' of /linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (75 commits)
Ethernet driver for EISA only SNI RM200/RM400 machines
Extract chip specific code out of lasi_82596.c
ehea: Whitespace cleanup
pasemi_mac: Fix TX interrupt threshold
spidernet: Replace literal with const
r8169: perform RX config change after mac filtering
r8169: mac address change support
r8169: display some extra debug information during startup
r8169: add endianess annotations to [RT]xDesc
r8169: align the IP header when there is no DMA constraint
r8169: add bit description for the TxPoll register
r8169: cleanup
r8169: remove the media option
r8169: small 8101 comment
r8169: confusion between hardware and IP header alignment
r8169: merge with version 8.001.00 of Realtek's r8168 driver
r8169: merge with version 6.001.00 of Realtek's r8169 driver
r8169: prettify mac_version
r8169: populate the hw_start handler for the 8110
r8169: populate the hw_start handler for the 8168
...
Stefan Richter [Mon, 2 Jul 2007 19:04:44 +0000 (21:04 +0200)]
firewire: fw-sbp2: fix DMA mapping of management ORBs
The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Mon, 2 Jul 2007 19:04:08 +0000 (21:04 +0200)]
firewire: fw-sbp2: fix DMA mapping of command ORBs
The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Mon, 2 Jul 2007 20:07:34 +0000 (22:07 +0200)]
firewire: fw-sbp2: fix DMA mapping of S/G tables
- The CPU must not touch the buffer after it was DMA-mapped.
- The size argument of dma_unmap_single(...page_table...) was bogus.
- Move a comment closer to the code to which it refers to.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 1 Jul 2007 11:56:03 +0000 (13:56 +0200)]
firewire: fw-sbp2: add a boundary check
Add rudimentary check for the case that the page table overflows due to
merging of s/g elements by the IOMMU. This would have lead to
overwriting of arbitrary memory.
After this change I expect that an offending command will be
unsuccessfully retried until the scsi_device is taken offline by SCSI
core. It's a border case and not worth to implement a recovery
strategy.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 1 Jul 2007 11:55:31 +0000 (13:55 +0200)]
firewire: fw-sbp2: correctly align page tables
This is required per SBP-2 clause 5.2.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 1 Jul 2007 11:54:57 +0000 (13:54 +0200)]
firewire: fw-sbp2: memset wants string.h
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 1 Jul 2007 11:54:24 +0000 (13:54 +0200)]
firewire: fw-sbp2: use correct speed in sbp2_agent_reset
noticed by Jay Fenlason
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Jay Fenlason [Wed, 27 Jun 2007 20:04:33 +0000 (16:04 -0400)]
firewire: fw-sbp2: correctly dereference by container_of
Replace a cast with a container_of(). As long as nobody reorders the
structure elements, they do the same thing, but container_of() is more
readable.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb)
Acked-by: Kristian Høgsberg <krh@redhat.com>
Kristian Høgsberg [Thu, 21 Jun 2007 22:20:34 +0000 (00:20 +0200)]
firewire: Document userspace ioctl interface.
The isochronous packet format is still not documented, but this
is a good first step.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (format, wording)
Stefan Richter [Sun, 17 Jun 2007 21:55:41 +0000 (23:55 +0200)]
firewire: fw-sbp2: implement nonexclusive login
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Mon, 18 Jun 2007 16:46:49 +0000 (18:46 +0200)]
firewire: fw-sbp2: let SCSI shutdown commands through before logout
This affects of course only the "soft shutdown" case, e.g. "modprobe -r
firewire-sbp2", while it doesn't matter for hot unplug.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 17 Jun 2007 21:52:08 +0000 (23:52 +0200)]
firewire: fw-sbp2: implement max sectors limit for some old bridges
This currently only affects one bridge in the hardwired blacklist.
I don't own one of those, hence haven't tested it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 17 Jun 2007 21:39:58 +0000 (23:39 +0200)]
firewire: simplify a struct type
cleanup after "firewire: support S100B...S400B and link slower than PHY"
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sun, 10 Jun 2007 19:31:36 +0000 (21:31 +0200)]
firewire: support S100B...S400B and link slower than PHY
Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.
Log the effective maximum speed of newly created nodes in dmesg.
Also, read the config ROM (except bus info block) at the maximum speed
rather than S100. This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.
The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Mon, 18 Jun 2007 17:44:12 +0000 (19:44 +0200)]
firewire: optimize gap count with 1394b leaf nodes
Table-based gap count optimization cannot be used if 1394b repeater PHYs
are present. But it does work with 1394b leaf nodes.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Sat, 9 Jun 2007 17:27:07 +0000 (19:27 +0200)]
firewire: remove unused macro
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 9 Jun 2007 17:26:22 +0000 (19:26 +0200)]
firewire: missing newline in printk
Also remove some errno printouts which will be shown by infrastructure
code anyway.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Fri, 11 May 2007 21:04:08 +0000 (23:04 +0200)]
firewire: fw-sbp2: remove unused struct member
cleanup after support of single-buffer requests was dropped
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Stefan Richter [Sun, 24 Jun 2007 13:31:54 +0000 (15:31 +0200)]
ieee1394: remove old isochronous ABI
Based on patch "the scheduled removal of RAW1394_REQ_ISO_{SEND,LISTEN}"
from Adrian Bunk, November 20 2006.
This patch also removes the underlying facilities in ohci1394 and
disables them in pcilynx. That is, hpsb_host_driver.devctl() and
hpsb_host_driver.transmit_packet() are no longer used for iso reception
and transmission.
Since video1394 and dv1394 only work with ohci1394 and raw1394's rawiso
interface has never been implemented in pcilynx, pcilynx is now no
longer useful for isochronous applications.
raw1394 will still handle the request types but will complete the
requests with errors that indicate API version conflicts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 17 Jun 2007 21:54:52 +0000 (23:54 +0200)]
ieee1394: sbp2: change some module parameters from int to bool
This is upwards compatible, except that integer values other than 0 or 1
are no longer accepted. But values like "Y", "N", "no", "nnoooh!" work
now.
Also, improve a comment on the serialize_io parameter and make the
ORB_SET_EXCLUSIVE macro ultra-safe.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 8 Jul 2007 11:34:21 +0000 (13:34 +0200)]
ieee1394: first minimal NUMA awareness
Association of a host device with a node on NUMA machines optimizes
allocations of skbs given from the networking stack to eth1394.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 27 May 2007 21:14:05 +0000 (23:14 +0200)]
ieee1394: eth1394: revert parent device to that in 2.6.20
After ieee1394 was converted away from class_device like the networking
subsystem was already in 2.6.21, eth1394's device may point to the
fw-host device as its parent again like in 2.6.20.
This affects userspace tools which examine the sysfs representation of
eth1394's device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 17 Jun 2007 21:47:45 +0000 (23:47 +0200)]
ieee1394: nodemgr: parallelize between several hosts
Remove the global nodemgr_serialize mutex which enclosed most of the
host thread event loop. This allows for parallelism between several
host adapter cards.
Properly serialize the driver hooks .update(), .suspend(), .resume(),
and .remove() by means of device->sem. These hooks can be called from
outside the host threads' contexts.
Get() and put() the device.driver when calling its hooks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Kay Sievers [Fri, 25 May 2007 09:50:53 +0000 (11:50 +0200)]
ieee1394: convert ieee1394 from "struct class_device" to "struct device"
Here is a straightforward conversion to "struct device". The "struct
class_device" will be removed from the kernel.
It seems to work fine for me with and without CONFIG_SYSFS_DEPRECATED
set.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Wed, 4 Jul 2007 21:13:53 +0000 (23:13 +0200)]
ieee1394: raw1394: fix a 32/64-bits compat fix
I was told that only i386 aligns 64 bit integers at 4 bytes boundaries
while all other architectures (32 bit architectures with 64 bit
siblings) align it on 8 bytes boundaries.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Mon, 21 May 2007 16:52:06 +0000 (18:52 +0200)]
ieee1394: raw1394: Add ioctl() for 32bit userland on 64bit kernel, amendment
Pointed out by Arnd Bergmann: PPC32 aligns this at 64bit, IA32 packs
it. A kernel-wide available __compat_u64 which is 4-byte aligned on
AMD64 and IA64 would be nicer though.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Petr Vandrovec [Mon, 7 May 2007 02:14:47 +0000 (04:14 +0200)]
ieee1394: raw1394: Add ioctl() for 32bit userland on 64bit kernel
Add compat_ioctl. Although all structures are more or less same,
raw1394_iso_packets got pointer inside, and raw1394_cycle_timer got unwanted
padding in the middle. I did not add any translation for ioctls passing array
of integers around as integers seem to have same size (32 bits) on all
architectures supported by Linux.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Dan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
Petr Vandrovec [Mon, 7 May 2007 02:14:47 +0000 (04:14 +0200)]
ieee1394: raw1394: Fix write() for 32bit userland on 64bit kernel
* write(fd, buf, 52) from 32bit app was returning 56. Most of callers did not
care, but some (arm registration) did, and anyway it looks bad if request for
writing 52 bytes returns 56. And returning sizeof anything in 'int' is not
good as well. So all functions now return '0' instead of
sizeof(struct raw1394_request) on success, and write() itself provides correct
return value (it just returns value it was asked to write on success as raw1394
does not do any partial writes at all).
* Related to this was problem that write() could have returned 0 when kernel
state would become corrupted and moved to different state than
opened/initialized/connected. Now it returns -EBADFD which seemed appropriate.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Dan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
Petr Vandrovec [Mon, 7 May 2007 02:14:47 +0000 (04:14 +0200)]
ieee1394: raw1394: Fix read() for 32bit userland on 64bit kernel
read() always failed with -EFAULT. This was happening due to
raw1394_compat_read copying data to wrong location - access_ok always
failed as 'r' is kernel address, not user. Whole function just tried to
copy data from 'r' to 'r', which is not good.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Dan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
Stefan Richter [Sat, 19 May 2007 10:29:37 +0000 (12:29 +0200)]
ieee1394: add comments in struct hpsb_packet
to clarify who is supposed to set what
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 3 May 2007 18:24:19 +0000 (20:24 +0200)]
ieee1394: ohci1394: remove dead CONFIG variable
spotted by Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Adrian Bunk [Mon, 9 Jul 2007 21:17:59 +0000 (23:17 +0200)]
drivers/ide/ide-dma.c: unexport ide_set_dma
ide_set_dma no longer has any modular user.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Mon, 9 Jul 2007 21:17:58 +0000 (23:17 +0200)]
via82cxxx: backport short cables support from pata_via.c
Backport short cables support from pata_via.c.
This patch should allow UDMA > 2 modes on Acer Ferrari 3400.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Bartlomiej Zolnierkiewicz [Mon, 9 Jul 2007 21:17:58 +0000 (23:17 +0200)]
sis5513: backport short cables support from pata_sis.c
Backport short cables support from pata_sis.c.
This patch allows UDMA > 2 modes on ASUS A6K.
Thanks to testing this patch goes out to Jiri Stavinoha.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Bartlomiej Zolnierkiewicz [Mon, 9 Jul 2007 21:17:58 +0000 (23:17 +0200)]
alim15x3: backport short cables support from pata_ali.c
Backport short cables support from pata_ali.c and while at it cleanup
existing cable detection code.
This patch should allow UDMA > 2 modes on HP Pavilion N5430 and Fujitsu P2000.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Bartlomiej Zolnierkiewicz [Mon, 9 Jul 2007 21:17:58 +0000 (23:17 +0200)]
piix: backport short cables support from ata_piix.c
Backport short cables support from ata_piix.c.
This patch should allow UDMA > 2 modes on:
- Acer 5602WLMi
- Acer 3682WLMi
- Asus W5F
- Acer Aspire 2023WLMi
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Bartlomiej Zolnierkiewicz [Mon, 9 Jul 2007 21:17:58 +0000 (23:17 +0200)]
ide: add short cables support
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter. Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.
Next patches add automatic detection of some systems using short cables.
Changes:
* Rename hwif->udma_four to hwif->cbl and make it u8.
* Convert all existing users accordingly (use ATA_CBL_* defines while at it).
* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().
* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Bartlomiej Zolnierkiewicz [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
ide: convert ide_find_best_mode() users to use ide_max_dma_mode()
ide-timing.h:
* remove handling of DMA modes from ide_find_best_mode() and rename it to
ide_find_best_pio_mode()
* drop no longer needed "map" argument from ide_find_best_pio_mode()
and delete needless ->id check
* remove no longer needed XFER_SWDMA and XFER_UDMA* defines
au1xxx-ide.c:
* use ide_max_dma_mode() instead of ide_find_best_mode()
* remove needless CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA #ifdef
amd74xx.c:
* store UDMA masks in amd_ide_chip[] and while at it make "base" field
to be u8 instead of unsigned long
* convert the driver to use UDMA masks from amd_ide_chip[]
* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
of ide_find_best_mode()
* delete stale comment from amd74xx_ide_dma_check()
* remove no longer needed AMD_UDMA* defines
via82cxxx.c:
* remove unused DISPLAY_VIA_TIMINGS define
* store UDMA masks in via_isa_bridges[] and while at it make "flags" field
to be u8 instead of u16
* convert the driver to use UDMA masks from via_isa_bridges[]
* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
of ide_find_best_mode()
* remove no longer needed VIA_UDMA* defines
pmac.c:
* use ide_max_dma_mode() instead of ide_find_best_mode()
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Bartlomiej Zolnierkiewicz [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
ide: fix pre-EIDE SWDMA support
If the word 62 is not defined use the word 52 to get SWDMA mask
in ide_get_mode_mask().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Andi Drebes [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
drivers/ide/legacy/hd.c: Array size calculation using sizeof replaced with ARRAY_SIZE
This patch replaces an array size calculation in drivers/ide/legacy/hd.c
that was done using sizeof with the ARRAY_SIZE macro.
Tested by compilation on an i386 box using "allyesconfig".
Diffed against Linus' git-tree.
Signed-off-by: Andi Drebes <lists-receive@programmierforen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Robert P. J. Day [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
ide: remove content related to dead CONFIG_BLK_DEV_MAC_MEDIABAY config variable
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Robert P. J. Day [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
ide: remove references to the non-existent CONFIG_SCSI_EATA_DMA
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Robert P. J. Day [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
ide-cd: replace C code with call to ARRAY_SIZE() macro
Delete the unnecessary macro ARY_LEN and use ARRAY_SIZE directly.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Junio C Hamano [Mon, 9 Jul 2007 21:17:57 +0000 (23:17 +0200)]
ide_in_drive_list(): "ALL" is not a wildcard anymore
This removes the support to treat "ALL" as a wildcard for
firmware revision. This is made a separate patch, as it will
break out-of-tree ide drivers that feed its own table that uses
"ALL" as the wildcard to ide_in_drive_list().
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Junio C Hamano [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
mips au1xxx_ide.h: use NULL as firmware-revision wildcard
This updates the DMA whitelist in MIPS specific au1xxx ide
driver to use NULL instead of "ALL" as the wildcard.
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Junio C Hamano [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
ide_in_drive_list(): accept NULL as the wildcard for firmware revision
Earlier, the matching of (model,rev) in ide-dma black/white list
handling was to consider "ALL" in the table to match any
revision. This makes NULL to be also an accepted wildcard, and
changes the entries of tables in ide-dma.c to use NULL.
The code still accepts "ALL" as the wildcard, in order to keep
any out-of-tree ide driver that feeds its own table that uses
"ALL" as the wildcard to ide_in_drive_list() function from
breaking.
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
aec62xx: kill speedproc() method wrapper (take 2)
There's no reason to have the speedproc() method wrapper for the two quite
different chip families, so just get rid of it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Matthias Kaehlcke [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
ide: use mutex instead of ide_setting_sem semaphore in IDE driver
The IDE driver uses a semaphore as mutex.
Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
--
Sergei Shtylyov [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
aec62xx: remove init_dma() method (take 2)
Get rid of the init_dma() method (which had no particular reason to exist) by
folding it into the init_hwif() method. While at it, also perform some cleanup
in the latter method:
- get rid of the useless clearing of hwif->autodma;
- fold the serialization code into one 'if' statement;
- fold setting the drives' 'autotune' and 'autodma' fields into the single
statements...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Mon, 9 Jul 2007 21:17:56 +0000 (23:17 +0200)]
aec62xx: rework init_setup_aec6x80()
Rework init_setup_aec6x80() so that it won't rewrite the constant name strings
anymore -- in order to do this:
- in aec62xx_init_one(), pass a local copy of 'struct pci_device_id' down the
call chain;
- change the names for in aec62xx_chipsets[] to default to AEC-6280[R];
- override the 'name' field in init_setup_aec6x80() only if bit 4 of the DMA
status register is set.
While at it, also change the 'udma_mask' field for AEC-6x80R chips in this
function and remove the code doing the same from the init_hwif() method...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Mon, 9 Jul 2007 21:17:55 +0000 (23:17 +0200)]
cmd64x: init. code cleanup
Fix two minor issues with PCI0646 chip reporting in the init_chipset() method:
"IRQ workaround enabled" message printed out not only for revision 0x01 and
"CMD646: chipset revision" printed twice (by IDE core and the driver itself).
Also, remove empty/pointless switch cases for the chips other than PCI0646,
duplicate write to the MRDMODE register when enabling interrupts and MEMORY
READ LINE cycles, and needless/misplaced initialization of the timing registers
in this method.
Switch to reading only the PCI revision ID register itself, not the whole 32
bits at its address in init_chipset() and init_hwif() methods; in addition,
get rid of the useless clearing of hwif->autodma and perform some cosmetic
style changes in the latter method.
Refactor ata66_cmd64x() by moving all the code into the 'switch' statement,
renaming/adding variables, and fixing the coding style.
While at it, finally get rid of the meaningless aliasing register #define's...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Mon, 9 Jul 2007 21:17:55 +0000 (23:17 +0200)]
hpt366: simplify UltraDMA filtering (take 4)
Simplify UltraDMA mode filtering in the driver:
- make use of the newly introduced 'udma_mask' field of 'ide_pci_device_t' to
set the correct hwif->ultra_mask, modifying init_setup_hpt366() to select
the correct mask based on the chip revision;
- replace 'max_mode' field of the 'struct hpt_info' with 'max_ultra' specifying
the maximum UltraDMA mode allowed;
- rewrite hpt3xx_udma_filter() to differ the filters based on the 'chip_type'
field, and only use it for HPT366 and HPT370[A] where it's really necessary.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Matthias Kaehlcke [Mon, 9 Jul 2007 21:17:55 +0000 (23:17 +0200)]
ide: use mutex instead of ide_cfg_sem semaphore in IDE driver
The IDE driver uses a semaphore as mutex.
Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Mon, 9 Jul 2007 21:17:54 +0000 (23:17 +0200)]
ide: make void and rename ide_dma_timeout() method
Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:
- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;
- in au1xxx-ide.c, get rid of commented out printk();
- in sl82c105.c, get rid of unnecessary variables.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Mon, 9 Jul 2007 21:17:54 +0000 (23:17 +0200)]
ide: make void and rename ide_dma_lostirq() method
Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:
- in aec62xx.c, rename the method in accordance with other drivers, and get rid
of unnecessary variables there;
- in pdc202xx_old.c, define/use 'hwif' variable;
- in sgiioc4.c, rearrange the code to call the resetproc() method directly.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>