OSDN Git Service
Xin Long [Mon, 12 Nov 2018 17:08:25 +0000 (01:08 +0800)]
l2tp: fix a sock refcnt leak in l2tp_tunnel_register
This issue happens when trying to add an existent tunnel. It
doesn't call sock_put() before returning -EEXIST to release
the sock refcnt that was held by calling sock_hold() before
the existence check.
This patch is to fix it by holding the sock after doing the
existence check.
Fixes:
f6cd651b056f ("l2tp: fix race in duplicate tunnel detection")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 12 Nov 2018 16:06:12 +0000 (17:06 +0100)]
s390/ism: clear dmbe_mask bit before SMC IRQ handling
SMC-D stress workload showed connection stalls. Since the firmware
decides to skip raising an interrupt if the SBA DMBE mask bit is
still set, this SBA DMBE mask bit should be cleared before the
IRQ handling in the SMC code runs. Otherwise there are small windows
possible with missing interrupts for incoming data.
SMC-D currently does not care about the old value of the SBA DMBE
mask.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Nov 2018 16:51:17 +0000 (08:51 -0800)]
Merge branch 'qed-Miscellaneous-bug-fixes'
Denis Bolotin says:
====================
qed: Miscellaneous bug fixes
This patch series fixes several unrelated bugs across the driver.
Please consider applying to net.
V1->V2:
-------
Use dma_rmb() instead of rmb().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Mon, 12 Nov 2018 10:50:23 +0000 (12:50 +0200)]
qed: Fix reading wrong value in loop condition
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 12 Nov 2018 10:50:22 +0000 (12:50 +0200)]
qed: Fix rdma_info structure allocation
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes:
51ff17251c9c ("qed: Add support for RoCE hw init")
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Mon, 12 Nov 2018 10:50:21 +0000 (12:50 +0200)]
qed: Fix overriding offload_tc by protocols without APP TLV
The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Mon, 12 Nov 2018 10:50:20 +0000 (12:50 +0200)]
qed: Fix PTT leak in qed_drain()
Release PTT before entering error flow.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Nov 2018 16:43:05 +0000 (08:43 -0800)]
Merge tag 'linux-can-fixes-for-4.20-
20181109' of ssh://gitolite./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-11-09
this is a pull request of 20 patches for net/master.
First we have a patch by Oliver Hartkopp which changes the raw socket's
raw_sendmsg() to return an error value if the user tries to send a CANFD
frame to a CAN-2.0 device.
The next two patches are by Jimmy Assarsson and fix potential problems
in the kvaser_usb driver.
YueHaibing's patches for the ucan driver fix a compile time warning and
remove a duplicate include.
Eugeniu Rosca patch adds more binding documentation to the rcar_can
driver bindings. The next two patches are by Fabrizio Castro for the
rcar_can driver and fixes a problem in the driver's probe function and
document the r8a774a1 binding.
Lukas Wunner's patch fixes a recpetion problem in hi311x driver by
switching from edge to level triggered interruts.
The next three patches all target the flexcan driver. Pankaj Bansal's
patch unconditionally unlocks the last mailbox used for RX. Alexander
Stein provides a better workaround for a hardware limitation when
sending RTR frames, by using the last mailbox for TX, resulting in fewer
lost frames. The patch by me simplyfies the driver, by making a runtime
value a compile time constant.
The following 4 patches are by me and provide the groundwork for the
next patches by Oleksij Rempel. To avoid code duplication common code in
the common CAN driver infrastructure is factured out and error handling
is cleaned up.
The next 4 patches are by Oleksij Rempel and fix the problem in the
flexcan driver that other processes see TX frames arrive out of order
with ragards to a RX'ed frame (which are send by a different system on
the CAN bus as the result of our TX frame).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Mon, 12 Nov 2018 02:27:34 +0000 (18:27 -0800)]
bnx2x: Assign unique DMAE channel number for FW DMAE transactions.
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 11 Nov 2018 23:12:31 +0000 (17:12 -0600)]
Linux 4.20-rc2
Linus Torvalds [Sun, 11 Nov 2018 23:09:48 +0000 (17:09 -0600)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"One last pull request before heading to Vancouver for LPC, here we have:
1) Don't forget to free VSI contexts during ice driver unload, from
Victor Raj.
2) Don't forget napi delete calls during device remove in ice driver,
from Dave Ertman.
3) Don't request VLAN tag insertion of ibmvnic device when SKB
doesn't have VLAN tags at all.
4) IPV4 frag handling code has to accomodate the situation where two
threads try to insert the same fragment into the hash table at the
same time. From Eric Dumazet.
5) Relatedly, don't flow separate on protocol ports for fragmented
frames, also from Eric Dumazet.
6) Memory leaks in qed driver, from Denis Bolotin.
7) Correct valid MTU range in smsc95xx driver, from Stefan Wahren.
8) Validate cls_flower nested policies properly, from Jakub Kicinski.
9) Clearing of stats counters in mc88e6xxx driver doesn't retain
important bits in the G1_STATS_OP register causing the chip to
hang. Fix from Andrew Lunn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
act_mirred: clear skb->tstamp on redirect
net: dsa: mv88e6xxx: Fix clearing of stats counters
tipc: fix link re-establish failure
net: sched: cls_flower: validate nested enc_opts_policy to avoid warning
net: mvneta: correct typo
flow_dissector: do not dissect l4 ports for fragments
net: qualcomm: rmnet: Fix incorrect assignment of real_dev
net: aquantia: allow rx checksum offload configuration
net: aquantia: invalid checksumm offload implementation
net: aquantia: fixed enable unicast on 32 macvlan
net: aquantia: fix potential IOMMU fault after driver unbind
net: aquantia: synchronized flow control between mac/phy
net: smsc95xx: Fix MTU range
net: stmmac: Fix RX packet size > 8191
qed: Fix potential memory corruption
qed: Fix SPQ entries not returned to pool in error flows
qed: Fix blocking/unlimited SPQ entries leak
qed: Fix memory/entry leak in qed_init_sp_request()
inet: frags: better deal with smp races
net: hns3: bugfix for not checking return value
...
Linus Torvalds [Sun, 11 Nov 2018 22:57:55 +0000 (16:57 -0600)]
Merge tag 'kbuild-fixes-v4.20' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix build errors in binrpm-pkg and bindeb-pkg targets
- fix false positive matches in merge_config.sh
- fix build version mismatch in deb-pkg target
- fix dtbs_install handling in (bin)deb-pkg target
- revert a commit that allows setlocalversion to write to source tree
* tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
builddeb: Fix inclusion of dtbs in debian package
Revert "scripts/setlocalversion: git: Make -dirty check more robust"
kbuild: deb-pkg: fix too low build version number
kconfig: merge_config: avoid false positive matches from comment lines
kbuild: deb-pkg: fix bindeb-pkg breakage when O= is used
kbuild: rpm-pkg: fix binrpm-pkg breakage when O= is used
Linus Torvalds [Sun, 11 Nov 2018 22:54:38 +0000 (16:54 -0600)]
Merge tag 'for-4.20-rc1-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Several fixes to recent release (4.19, fixes tagged for stable) and
other fixes"
* tag 'for-4.20-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix missing delayed iputs on unmount
Btrfs: fix data corruption due to cloning of eof block
Btrfs: fix infinite loop on inode eviction after deduplication of eof block
Btrfs: fix deadlock on tree root leaf when finding free extent
btrfs: avoid link error with CONFIG_NO_AUTO_INLINE
btrfs: tree-checker: Fix misleading group system information
Btrfs: fix missing data checksums after a ranged fsync (msync)
btrfs: fix pinned underflow after transaction aborted
Btrfs: fix cur_offset in the error case for nocow
Linus Torvalds [Sun, 11 Nov 2018 22:53:02 +0000 (16:53 -0600)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes, mostly buffer and memory leaks on
error return cleanup paths"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: missing !bh check in ext4_xattr_inode_write()
ext4: fix buffer leak in __ext4_read_dirblock() on error path
ext4: fix buffer leak in ext4_expand_extra_isize_ea() on error path
ext4: fix buffer leak in ext4_xattr_move_to_block() on error path
ext4: release bs.bh before re-using in ext4_xattr_block_find()
ext4: fix buffer leak in ext4_xattr_get_block() on error path
ext4: fix possible leak of s_journal_flag_rwsem in error path
ext4: fix possible leak of sbi->s_group_desc_leak in error path
ext4: remove unneeded brelse call in ext4_xattr_inode_update_ref()
ext4: avoid possible double brelse() in add_new_gdb() on error path
ext4: avoid buffer leak in ext4_orphan_add() after prior errors
ext4: avoid buffer leak on shutdown in ext4_mark_iloc_dirty()
ext4: fix possible inode leak in the retry loop of ext4_resize_fs()
ext4: fix missing cleanup if ext4_alloc_flex_bg_array() fails while resizing
ext4: add missing brelse() update_backups()'s error path
ext4: add missing brelse() add_new_gdb_meta_bg()'s error path
ext4: add missing brelse() in set_flexbg_block_bitmap()'s error path
ext4: avoid potential extra brelse in setup_new_flex_group_blocks()
Linus Torvalds [Sun, 11 Nov 2018 22:41:50 +0000 (16:41 -0600)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes:
- Cure the LDT remapping to user space on 5 level paging which ended
up in the KASLR space
- Remove LDT mapping before freeing the LDT pages
- Make NFIT MCE handling more robust
- Unbreak the VSMP build by removing the dependency on paravirt ops
- Support broken PIT emulation on Microsoft hyperV
- Don't trace vmware_sched_clock() to avoid tracer recursion
- Remove -pipe from KBUILD CFLAGS which breaks clang and is also
slower on GCC
- Trivial coding style and typo fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/vmware: Do not trace vmware_sched_clock()
x86/vsmp: Remove dependency on pv_irq_ops
x86/ldt: Remove unused variable in map_ldt_struct()
x86/ldt: Unmap PTEs for the slot before freeing LDT pages
x86/mm: Move LDT remap out of KASLR region on 5-level paging
acpi/nfit, x86/mce: Validate a MCE's address before using it
acpi/nfit, x86/mce: Handle only uncorrectable machine checks
x86/build: Remove -pipe from KBUILD_CFLAGS
x86/hyper-v: Fix indentation in hv_do_fast_hypercall16()
Documentation/x86: Fix typo in zero-page.txt
x86/hyper-v: Enable PIT shutdown quirk
clockevents/drivers/i8253: Add support for PIT shutdown quirk
Linus Torvalds [Sun, 11 Nov 2018 22:39:12 +0000 (16:39 -0600)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A bunch of perf tooling fixes:
- Make the Intel PT SQL viewer more robust
- Make the Intel PT debug log more useful
- Support weak groups in perf record so it's behaving the same way as
perf stat
- Display the LBR stats in callchain entries properly in perf top
- Handle different PMu names with common prefix properlin in pert
stat
- Start syscall augmenting in perf trace. Preparation for
architecture independent eBPF instrumentation of syscalls.
- Fix build breakage in JVMTI perf lib
- Fix arm64 tools build failure wrt smp_load_{acquire,release}"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Do not zero sample_id_all for group members
perf tools: Fix undefined symbol scnprintf in libperf-jvmti.so
perf beauty: Use SRCARCH, ARCH=x86_64 must map to "x86" to find the headers
perf intel-pt: Add MTC and CYC timestamps to debug log
perf intel-pt: Add more event information to debug log
perf scripts python: exported-sql-viewer.py: Fix table find when table re-ordered
perf scripts python: exported-sql-viewer.py: Add help window
perf scripts python: exported-sql-viewer.py: Add Selected branches report
perf scripts python: exported-sql-viewer.py: Fall back to /usr/local/lib/libxed.so
perf top: Display the LBR stats in callchain entry
perf stat: Handle different PMU names with common prefix
perf record: Support weak groups
perf evlist: Move perf_evsel__reset_weak_group into evlist
perf augmented_syscalls: Start collecting pathnames in the BPF program
perf trace: Fix setting of augmented payload when using eBPF + raw_syscalls
perf trace: When augmenting raw_syscalls plug raw_syscalls:sys_exit too
perf examples bpf: Start augmenting raw_syscalls:sys_{start,exit}
tools headers barrier: Fix arm64 tools build failure wrt smp_load_{acquire,release}
Linus Torvalds [Sun, 11 Nov 2018 22:37:41 +0000 (16:37 -0600)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"Just the removal of a redundant call into the sched deadline overrun
check"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Remove useless call to check_dl_overrun()
Linus Torvalds [Sun, 11 Nov 2018 22:33:00 +0000 (16:33 -0600)]
Merge branch 'sched/urgent' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two small scheduler fixes:
- Take hotplug lock in sched_init_smp(). Technically not really
required, but lockdep will complain other.
- Trivial comment fix in sched/fair"
* 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix a comment in task_numa_fault()
sched/core: Take the hotplug lock in sched_init_smp()
Linus Torvalds [Sun, 11 Nov 2018 22:18:10 +0000 (16:18 -0600)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking build fix from Thomas Gleixner:
"A single fix for a build fail with CONFIG_PROFILE_ALL_BRANCHES=y in
the qspinlock code"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/qspinlock: Fix compile error
Linus Torvalds [Sun, 11 Nov 2018 22:14:05 +0000 (16:14 -0600)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"A couple of fixlets for the core:
- Kernel doc function documentation fixes
- Missing prototypes for weak watchdog functions"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
resource/docs: Complete kernel-doc style function documentation
watchdog/core: Add missing prototypes for weak functions
resource/docs: Fix new kernel-doc warnings
Eric Dumazet [Sun, 11 Nov 2018 00:22:29 +0000 (16:22 -0800)]
act_mirred: clear skb->tstamp on redirect
If sch_fq is used at ingress, skbs that might have been
timestamped by net_timestamp_set() if a packet capture
is requesting timestamps could be delayed by arbitrary
amount of time, since sch_fq time base is MONOTONIC.
Fix this problem by moving code from sch_netem.c to act_mirred.c.
Fixes:
fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 10 Nov 2018 23:41:10 +0000 (00:41 +0100)]
net: dsa: mv88e6xxx: Fix clearing of stats counters
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes:
40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Sat, 10 Nov 2018 22:30:24 +0000 (17:30 -0500)]
tipc: fix link re-establish failure
When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.
The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.
If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.
However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.
We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.
Fixes:
7ea817f4e832 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Herring [Wed, 7 Nov 2018 14:36:46 +0000 (08:36 -0600)]
builddeb: Fix inclusion of dtbs in debian package
Commit
37c8a5fafa3b ("kbuild: consolidate Devicetree dtb build rules")
moved the location of 'dtbs_install' target which caused dtbs to not be
installed when building debian package with 'bindeb-pkg' target. Update
the builddeb script to use the same logic that determines if there's a
'dtbs_install' target which is presence of the arch dts directory. Also,
use CONFIG_OF_EARLY_FLATTREE instead of CONFIG_OF as that's a better
indication of whether we are building dtbs.
This commit will also have the side effect of installing dtbs on any
arch that has dts files. Previously, it was dependent on whether the
arch defined 'dtbs_install'.
Fixes:
37c8a5fafa3b ("kbuild: consolidate Devicetree dtb build rules")
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Guenter Roeck [Tue, 6 Nov 2018 18:10:38 +0000 (10:10 -0800)]
Revert "scripts/setlocalversion: git: Make -dirty check more robust"
This reverts commit
6147b1cf19651c7de297e69108b141fb30aa2349.
The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.
Output from "strace git status -uno --porcelain":
getcwd("/tmp/linux-test", 129) = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
-1 EROFS (Read-only file system)
While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.
Fixes:
6147b1cf19651 ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 6 Nov 2018 04:18:05 +0000 (13:18 +0900)]
kbuild: deb-pkg: fix too low build version number
Since commit
b41d920acff8 ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.
Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.
Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.
Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.
Fixes:
b41d920acff8 ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Masahiro Yamada [Mon, 5 Nov 2018 08:19:36 +0000 (17:19 +0900)]
kconfig: merge_config: avoid false positive matches from comment lines
The current SED_CONFIG_EXP could match to comment lines in config
fragment files, especially when CONFIG_PREFIX_ is empty. For example,
Buildroot uses empty prefixing; starting symbols with BR2_ is just
convention.
Make the sed expression more robust against false positives from
comment lines. The new sed expression matches to only valid patterns.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Linus Torvalds [Sat, 10 Nov 2018 19:32:14 +0000 (13:32 -0600)]
Merge tag 'tty-4.20-rc2' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty fixes for 4.20-rc2
One of these missed the original 4.19-final release, I missed that I
hadn't done a pull request for it as it was in linux-next and my
branch for a long time, that's my fault.
The others are small, fixing some reported issues and finally fixing
the termios mess for alpha so that glibc has a chance to implement
some missing functionality that has been pending for many years now.
All of these have been in linux-next with no reported issues"
* tag 'tty-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sh-sci: Fix could not remove dev_attr_rx_fifo_timeout
arch/alpha, termios: implement BOTHER, IBSHIFT and termios2
termios, tty/tty_baudrate.c: fix buffer overrun
vt: fix broken display when running aptitude
serial: sh-sci: Fix receive on SCIFA/SCIFB variants with DMA
Linus Torvalds [Sat, 10 Nov 2018 19:29:47 +0000 (13:29 -0600)]
Merge tag 'drm-fixes-2018-11-11' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"drm: i915, amdgpu, sun4i, exynos and etnaviv fixes:
- amdgpu has some display fixes, KFD ioctl fixes and a Vega20 bios
interaction fix.
- sun4i has some NULL checks added
- i915 has a 32-bit system fix, LPE audio oops, and HDMI2.0 clock
fixes.
- Exynos has a 3 regression fixes (one frame counter, fbdev missing,
dsi->panel check)
- Etnaviv has a single fencing fix for GPU recovery"
* tag 'drm-fixes-2018-11-11' of git://anongit.freedesktop.org/drm/drm: (39 commits)
drm/amd/amdgpu/dm: Fix dm_dp_create_fake_mst_encoder()
drm/amd/display: Drop reusing drm connector for MST
drm/amd/display: Cleanup MST non-atomic code workaround
drm/amd/powerplay: always use fast UCLK switching when UCLK DPM enabled
drm/amd/powerplay: set a default fclk/gfxclk ratio
drm/amdgpu/display/dce11: only enable FBC when selected
drm/amdgpu/display/dm: handle FBC dc feature parameter
drm/amdgpu/display/dc: add FBC to dc_config
drm/amdgpu: add DC feature mask module parameter
drm/amdgpu/display: check if fbc is available in set_static_screen_control (v2)
drm/amdgpu/vega20: add CLK base offset
drm/amd/display: Stop leaking planes
drm/amd/display: Fix misleading buffer information
Revert "drm/amd/display: set backlight level limit to 1"
drm/amd: Update atom_smu_info_v3_3 structure
drm/i915: Fix ilk+ watermarks when disabling pipes
drm/sun4i: tcon: prevent tcon->panel dereference if NULL
drm/sun4i: tcon: fix check of tcon->panel null pointer
drm/i915: Don't oops during modeset shutdown after lpe audio deinit
drm/i915: Mark pin flags as u64
...
Linus Torvalds [Sat, 10 Nov 2018 19:27:58 +0000 (13:27 -0600)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull namespace fixes from Eric Biederman:
"I believe all of these are simple obviously correct bug fixes. These
fall into two groups:
- Fixing the implementation of MNT_LOCKED which prevents lesser
privileged users from seeing unders mounts created by more
privileged users.
- Fixing the extended uid and group mapping in user namespaces.
As well as ensuring the code looks correct I have spot tested these
changes as well and in my testing the fixes are working"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
mount: Prevent MNT_DETACH from disconnecting locked mounts
mount: Don't allow copying MNT_UNBINDABLE|MNT_LOCKED mounts
mount: Retest MNT_LOCKED in do_umount
userns: also map extents in the reverse map to kernel IDs
Linus Torvalds [Sat, 10 Nov 2018 19:25:55 +0000 (13:25 -0600)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A small set of fixes for clk drivers.
One to fix a DT refcount imbalance, two to mark some Amlogic clks as
critical, and one final one that fixes a clk name for the Qualcomm
driver merged this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc: Fix board clock node name
clk: meson: axg: mark fdiv2 and fdiv3 as critical
clk: meson-gxbb: set fclk_div3 as CLK_IS_CRITICAL
clk: fixed-factor: fix of_node_get-put imbalance
Dave Airlie [Sat, 10 Nov 2018 18:20:48 +0000 (04:20 +1000)]
Merge branch 'drm-fixes-4.20' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.20:
- DC MST fixes
- DC FBC fix
- Vega20 updates to support the latest vbios
- KFD type fixes for ioctl headers
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108035551.2904-1-alexander.deucher@amd.com
Dave Airlie [Sat, 10 Nov 2018 18:19:52 +0000 (04:19 +1000)]
Merge tag 'drm-misc-fixes-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- sun4i: tcon->panel NULL deref protections (Giulio)
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107205051.GA27823@art_vandelay
Dave Airlie [Sat, 10 Nov 2018 18:14:22 +0000 (04:14 +1000)]
Merge tag 'drm-intel-fixes-2018-11-08' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Bugzilla #108282 fixed: Avoid graphics corruption on 32-bit systems for Mesa 18.2.x
Avoid OOPS on LPE audio deinit. Remove two unused W/As.
Fix to correct HDMI 2.0 audio clock modes to spec.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108134508.GA28466@jlahtine-desk.ger.corp.intel.com
Jakub Kicinski [Sat, 10 Nov 2018 05:06:26 +0000 (21:06 -0800)]
net: sched: cls_flower: validate nested enc_opts_policy to avoid warning
TCA_FLOWER_KEY_ENC_OPTS and TCA_FLOWER_KEY_ENC_OPTS_MASK can only
currently contain further nested attributes, which are parsed by
hand, so the policy is never actually used resulting in a W=1
build warning:
net/sched/cls_flower.c:492:1: warning: ‘enc_opts_policy’ defined but not used [-Wunused-const-variable=]
enc_opts_policy[TCA_FLOWER_KEY_ENC_OPTS_MAX + 1] = {
Add the validation anyway to avoid potential bugs when other
attributes are added and to make the attribute structure slightly
more clear. Validation will also set extact to point to bad
attribute on error.
Fixes:
0a6e77784f49 ("net/sched: allow flower to match tunnel options")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 10 Nov 2018 14:58:48 +0000 (08:58 -0600)]
Merge tag 'for-linus-4.20a-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Several fixes, mostly for rather recent regressions when running under
Xen"
* tag 'for-linus-4.20a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: remove size limit of privcmd-buf mapping interface
xen: fix xen_qlock_wait()
x86/xen: fix pv boot
xen-blkfront: fix kernel panic with negotiate_mq error path
xen/grant-table: Fix incorrect gnttab_dma_free_pages() pr_debug message
CONFIG_XEN_PV breaks xen_create_contiguous_region on ARM
Linus Torvalds [Sat, 10 Nov 2018 13:07:21 +0000 (07:07 -0600)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix occasional page fault during boot due to memblock resizing before
the linear map is up.
- Define NET_IP_ALIGN to 0 to improve the DMA performance on some
platforms.
- lib/raid6 test build fix.
- .mailmap update for Punit Agrawal
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: memblock: don't permit memblock resizing until linear mapping is up
arm64: mm: define NET_IP_ALIGN to 0
lib/raid6: Fix arm64 test build
mailmap: Update email for Punit Agrawal
Linus Torvalds [Sat, 10 Nov 2018 12:57:34 +0000 (06:57 -0600)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has one bugfix (qcom-geni driver), one arch enablement (i2c-omap
driver, no code change), and a new driver (nvidia-gpu) this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
usb: typec: ucsi: add support for Cypress CCGx
i2c: nvidia-gpu: make pm_ops static
i2c: add i2c bus driver for NVIDIA GPU
i2c: qcom-geni: Fix runtime PM mismatch with child devices
MAINTAINERS: Add entry for i2c-omap driver
i2c: omap: Enable for ARCH_K3
dt-bindings: i2c: omap: Add new compatible for AM654 SoCs
Alexandre Belloni [Fri, 9 Nov 2018 16:37:20 +0000 (17:37 +0100)]
net: mvneta: correct typo
The reserved variable should be named reserved1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
배석진 [Sat, 10 Nov 2018 00:53:06 +0000 (16:53 -0800)]
flow_dissector: do not dissect l4 ports for fragments
Only first fragment has the sport/dport information,
not the following ones.
If we want consistent hash for all fragments, we need to
ignore ports even for first fragment.
This bug is visible for IPv6 traffic, if incoming fragments
do not have a flow label, since skb_get_hash() will give
different results for first fragment and following ones.
It is also visible if any routing rule wants dissection
and sport or dport.
See commit
5e5d6fed3741 ("ipv6: route: dissect flow
in input path if fib rules need it") for details.
[edumazet] rewrote the changelog completely.
Fixes:
06635a35d13d ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subash Abhinov Kasiviswanathan [Sat, 10 Nov 2018 01:56:27 +0000 (18:56 -0700)]
net: qualcomm: rmnet: Fix incorrect assignment of real_dev
A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.
sysctl call stack -
<6> Unable to handle kernel NULL pointer dereference at
virtual address
00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2> rmnet_vnd_get_iflink+0x1c/0x28
<2> inet6_fill_ifinfo+0x15c/0x234
<2> inet6_ifinfo_notify+0x68/0xd4
<2> ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2> proc_sys_call_handler+0xac/0x100
<2> proc_sys_write+0x3c/0x4c
<2> __vfs_write+0x54/0x14c
<2> vfs_write+0xcc/0x188
<2> SyS_write+0x60/0xc0
<2> el0_svc_naked+0x34/0x38
device register call stack -
<2> notifier_call_chain+0x84/0xbc
<2> raw_notifier_call_chain+0x38/0x48
<2> call_netdevice_notifiers_info+0x40/0x70
<2> call_netdevice_notifiers+0x38/0x60
<2> register_netdevice+0x29c/0x3d8
<2> rmnet_vnd_newlink+0x68/0xe8
<2> rmnet_newlink+0xa0/0x160
<2> rtnl_newlink+0x57c/0x6c8
<2> rtnetlink_rcv_msg+0x1dc/0x328
<2> netlink_rcv_skb+0xac/0x118
<2> rtnetlink_rcv+0x24/0x30
<2> netlink_unicast+0x158/0x1f0
<2> netlink_sendmsg+0x32c/0x338
<2> sock_sendmsg+0x44/0x60
<2> SyS_sendto+0x150/0x1ac
<2> el0_svc_naked+0x34/0x38
Fixes:
b752eff5be24 ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Nov 2018 23:38:11 +0000 (15:38 -0800)]
Merge branch 'aquantia-fixes'
Igor Russkikh says:
====================
net: aquantia: 2018-11 bugfixes
The patchset fixes a number of bugs found in various areas after
driver validation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 9 Nov 2018 11:54:03 +0000 (11:54 +0000)]
net: aquantia: allow rx checksum offload configuration
RX Checksum offloads could not be configured and ignored netdev features
flag for checksumming.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 9 Nov 2018 11:54:01 +0000 (11:54 +0000)]
net: aquantia: invalid checksumm offload implementation
Packets with marked invalid IP/UDP/TCP checksums were considered as good
by the driver. The error was in a logic, processing offload bits in
RX descriptor.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 9 Nov 2018 11:53:59 +0000 (11:53 +0000)]
net: aquantia: fixed enable unicast on 32 macvlan
Fixed a condition mistake due to which macvlans unicast
item number 32 was not added in the unicast filter.
The consequence is that when exactly 32 macvlans are created
on NIC, the last created macvlan receives no traffic because
its MAC was not registered in HW.
Fixes:
94b3b542303f ("net: aquantia: vlan unicast address list correct handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 9 Nov 2018 11:53:57 +0000 (11:53 +0000)]
net: aquantia: fix potential IOMMU fault after driver unbind
IOMMU fault may occurr on unbind/bind or if_down/if_up sequence.
Although driver disables the rings on down, this is not enough.
Due to internal HW design, during subsequent initialization
NIC sometimes may reuse RX descriptors cache and write to the
host memory from the descriptor cache.
That's get catched by IOMMU on host.
This patch invalidates the descriptor cache in NIC on interface down
to prevent writing to the cached descriptors and to the memory pointed
in those descriptors.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 9 Nov 2018 11:53:56 +0000 (11:53 +0000)]
net: aquantia: synchronized flow control between mac/phy
Flow control statuses were not synchronized between blocks,
that caused packets/link drop on some corner cases, when
MAC sent PFC although Phy was not expecting these to come.
Driver should readout the negotiated FC from phy and
configure RX block accordigly.
This is done on each link change event with information from FW.
Fixes:
288551de45aa ("net: aquantia: Implement rx/tx flow control ethtools callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 9 Nov 2018 22:41:58 +0000 (16:41 -0600)]
Merge tag 'devicetree-fixes-for-4.20-2' of git://git./linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- Add validation of NUMA distance map to prevent crashes with bad map
- Fix setting of dma_mask
* tag 'devicetree-fixes-for-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of, numa: Validate some distance map rules
of/device: Really only set bus DMA mask when appropriate
Linus Torvalds [Fri, 9 Nov 2018 22:31:51 +0000 (16:31 -0600)]
Merge tag 'for-linus-
20181109' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
- Two fixes for an ubd regression, one for missing locking, and one for
a missing initialization of a field. The latter was an old latent
bug, but it's now visible and triggers (Me, Anton Ivanov)
- Set of NVMe fixes via Christoph, but applied manually due to a git
tree mixup (Christoph, Sagi)
- Fix for a discard split regression, in three patches (Ming)
- Update libata git trees (Geert)
- SPDX identifier for sata_rcar (Kuninori Morimoto)
- Virtual boundary merge fix (Johannes)
- Preemptively clear memory we are going to pass to userspace, in case
the driver does a short read (Keith)
* tag 'for-linus-
20181109' of git://git.kernel.dk/linux-block:
block: make sure writesame bio is aligned with logical block size
block: cleanup __blkdev_issue_discard()
block: make sure discard bio is aligned with logical block size
Revert "nvmet-rdma: use a private workqueue for delete"
nvme: make sure ns head inherits underlying device limits
nvmet: don't try to add ns to p2p map unless it actually uses it
sata_rcar: convert to SPDX identifiers
ubd: fix missing initialization of io_req
block: Clear kernel memory before copying to user
MAINTAINERS: Fix remaining pointers to obsolete libata.git
ubd: fix missing lock around request issue
block: respect virtual boundary mask in bvecs
Linus Torvalds [Fri, 9 Nov 2018 22:26:18 +0000 (16:26 -0600)]
Merge tag 'ceph-for-4.20-rc2' of https://github.com/ceph/ceph-client
Pull Ceph fixes from Ilya Dryomov:
"Two CephFS fixes (copy_file_range and quota) and a small feature bit
cleanup"
* tag 'ceph-for-4.20-rc2' of https://github.com/ceph/ceph-client:
libceph: assume argonaut on the server side
ceph: quota: fix null pointer dereference in quota check
ceph: add destination file data sync before doing any remote copy
Linus Torvalds [Fri, 9 Nov 2018 22:21:24 +0000 (16:21 -0600)]
Merge tag 'mips_fixes_4.20_2' of git://git./linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple of small MIPS fixes for 4.20:
- Extend an array to avoid overruns on some Octeon hardware, fixing a
bug introduced in 4.3.
- Fix a coherent DMA regression for systems without cache-coherent
DMA introduced in the 4.20 merge window"
* tag 'mips_fixes_4.20_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Fix `dma_alloc_coherent' returning a non-coherent allocation
MIPS: OCTEON: fix out of bounds array access on CN68XX
Vinod Koul [Fri, 9 Nov 2018 09:50:54 +0000 (15:20 +0530)]
clk: qcom: gcc: Fix board clock node name
Device tree node name are not supposed to have "_" in them so fix the
node name use of xo_board to xo-board
Fixes:
652f1813c113 ("clk: qcom: gcc: Add global clock controller driver for QCS404")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Steven Rostedt (VMware) [Fri, 9 Nov 2018 20:22:07 +0000 (15:22 -0500)]
x86/cpu/vmware: Do not trace vmware_sched_clock()
When running function tracing on a Linux guest running on VMware
Workstation, the guest would crash. This is due to tracing of the
sched_clock internal call of the VMware vmware_sched_clock(), which
causes an infinite recursion within the tracing code (clock calls must
not be traced).
Make vmware_sched_clock() not traced by ftrace.
Fixes:
80e9a4f21fd7c ("x86/vmware: Add paravirt sched clock")
Reported-by: GwanYeong Kim <gy741.kim@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: Alok Kataria <akataria@vmware.com>
CC: GwanYeong Kim <gy741.kim@gmail.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
CC: Thomas Gleixner <tglx@linutronix.de>
CC: virtualization@lists.linux-foundation.org
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20181109152207.4d3e7d70@gandalf.local.home
Ajay Gupta [Fri, 26 Oct 2018 16:36:59 +0000 (09:36 -0700)]
usb: typec: ucsi: add support for Cypress CCGx
Latest NVIDIA GPU cards have a Cypress CCGx Type-C controller
over I2C interface.
This UCSI I2C driver uses I2C bus driver interface for communicating
with Type-C controller.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Yoshihiro Shimoda [Tue, 30 Oct 2018 06:13:35 +0000 (15:13 +0900)]
serial: sh-sci: Fix could not remove dev_attr_rx_fifo_timeout
This patch fixes an issue that the sci_remove() could not remove
dev_attr_rx_fifo_timeout because uart_remove_one_port() set
the port->port.type to PORT_UNKNOWN.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Fixes:
5d23188a473d ("serial: sh-sci: make RX FIFO parameters tunable via sysfs")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Fri, 9 Nov 2018 16:54:38 +0000 (17:54 +0100)]
i2c: nvidia-gpu: make pm_ops static
sparse rightfully says:
warning: symbol 'gpu_i2c_driver_pm' was not declared. Should it be static?
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Ajay Gupta [Fri, 26 Oct 2018 16:36:58 +0000 (09:36 -0700)]
i2c: add i2c bus driver for NVIDIA GPU
Latest NVIDIA GPU card has USB Type-C interface. There is a
Type-C controller which can be accessed over I2C.
This driver adds I2C bus driver to communicate with Type-C controller.
I2C client driver will be part of USB Type-C UCSI driver.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: kept Makefile sorting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Vasily Averin [Fri, 9 Nov 2018 16:34:40 +0000 (11:34 -0500)]
ext4: missing !bh check in ext4_xattr_inode_write()
According to Ted Ts'o ext4_getblk() called in ext4_xattr_inode_write()
should not return bh = NULL
The only time that bh could be NULL, then, would be in the case of
something really going wrong; a programming error elsewhere (perhaps a
wild pointer dereference) or I/O error causing on-disk file system
corruption (although that would be highly unlikely given that we had
*just* allocated the blocks and so the metadata blocks in question
probably would still be in the cache).
Fixes:
e50e5129f384 ("ext4: xattr-in-inode support")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org # 4.13
Oleksij Rempel [Tue, 18 Sep 2018 09:40:41 +0000 (11:40 +0200)]
can: flexcan: use can_rx_offload_queue_sorted() for flexcan_irq_bus_*()
Currently, in case of bus error, driver will generate error message and put
in the tail of the message queue. To avoid confusions, this change should
place the bus related messages in proper order.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Tue, 18 Sep 2018 09:40:40 +0000 (11:40 +0200)]
can: rx-offload: rename can_rx_offload_irq_queue_err_skb() to can_rx_offload_queue_tail()
This function has nothing todo with error.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Tue, 18 Sep 2018 09:40:39 +0000 (11:40 +0200)]
can: flexcan: handle tx-complete CAN frames via rx-offload infrastructure
Current flexcan driver will put TX-ECHO in regular unsorted way, in
this case TX-ECHO can come after the response to the same TXed message.
In some cases, for example for J1939 stack, things will break.
This patch is using new rx-offload API to put the messages just in the
right place.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephen Boyd [Fri, 2 Nov 2018 20:57:32 +0000 (13:57 -0700)]
i2c: qcom-geni: Fix runtime PM mismatch with child devices
We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.
Enabling runtime PM for inactive device (a98000.i2c) with active children
[...]
Call trace:
pm_runtime_enable+0xd8/0xf8
geni_i2c_probe+0x440/0x460
platform_drv_probe+0x74/0xc8
[...]
Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.
Fixes:
37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Vignesh R [Fri, 9 Nov 2018 11:14:12 +0000 (16:44 +0530)]
MAINTAINERS: Add entry for i2c-omap driver
Add separate entry for i2c-omap and add my name as maintainer for this
driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Vignesh R [Fri, 9 Nov 2018 11:14:11 +0000 (16:44 +0530)]
i2c: omap: Enable for ARCH_K3
Allow I2C_OMAP to be built for K3 platforms.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Vignesh R [Fri, 9 Nov 2018 11:14:10 +0000 (16:44 +0530)]
dt-bindings: i2c: omap: Add new compatible for AM654 SoCs
AM654 SoCs have same I2C IP as OMAP SoCs. Add new compatible to
handle AM654 SoCs. While at that reformat the existing compatible list
for older SoCs to list one valid compatible per line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Oleksij Rempel [Tue, 18 Sep 2018 09:40:38 +0000 (11:40 +0200)]
can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions
Current CAN framework can't guarantee proper/chronological order
of RX and TX-ECHO messages. To make this possible, drivers should use
this functions instead of can_get_echo_skb().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 31 Oct 2018 13:15:13 +0000 (14:15 +0100)]
can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb
Prior to echoing a successfully transmitted CAN frame (by calling
can_get_echo_skb()), CAN drivers have to put the CAN frame (by calling
can_put_echo_skb() in the transmit function). These put and get function
take an index as parameter, which is used to identify the CAN frame.
A driver calling can_get_echo_skb() with a index not pointing to a skb
is a BUG, so add an appropriate error message.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 31 Oct 2018 13:05:26 +0000 (14:05 +0100)]
can: dev: __can_get_echo_skb(): Don't crash the kernel if can_priv::echo_skb is accessed out of bounds
If the "struct can_priv::echo_skb" is accessed out of bounds would lead
to a kernel crash. Better print a sensible warning message instead and
try to recover.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 31 Oct 2018 10:08:21 +0000 (11:08 +0100)]
can: dev: __can_get_echo_skb(): replace struct can_frame by canfd_frame to access frame length
This patch replaces the use of "struct can_frame::can_dlc" by "struct
canfd_frame::len" to access the frame's length. As it is ensured that
both structures have a compatible memory layout for this member this is
no functional change. Futher, this compatibility is documented in a
comment.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 31 Oct 2018 09:37:46 +0000 (10:37 +0100)]
can: dev: can_get_echo_skb(): factor out non sending code to __can_get_echo_skb()
This patch factors out all non sending parts of can_get_echo_skb() into
a seperate function __can_get_echo_skb(), so that it can be re-used in
an upcoming patch.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 9 Nov 2018 14:01:50 +0000 (15:01 +0100)]
can: flexcan: remove not needed struct flexcan_priv::tx_mb and struct flexcan_priv::tx_mb_idx
The previous patch changes the TX path to always use the last mailbox
regardless of the used offload scheme (rx-fifo or timestamp based). This
means members "tx_mb" and "tx_mb_idx" of the struct flexcan_priv don't
depend on the offload scheme, so replace them by compile time constants.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Alexander Stein [Thu, 11 Oct 2018 15:01:25 +0000 (17:01 +0200)]
can: flexcan: Always use last mailbox for TX
Essentially this patch moves the TX mailbox to position 63, regardless
of timestamp based offloading or RX FIFO. So mainly the iflag register
usage regarding TX has changed. The rest is consolidating RX FIFO and
timestamp offloading as they now use both the same TX mailbox.
The reason is a very annoying behavior regarding sending RTR frames when
_not_ using RX FIFO:
If a TX mailbox sent a RTR frame it becomes a RX mailbox. For that
reason flexcan_irq disables the TX mailbox again. But if during the time
the RTR was sent and the TX mailbox is disabled a new CAN frames is
received, it is lost without notice. The reason is that so-called
"Move-in" process starts from the lowest mailbox which happen to be a TX
mailbox set to EMPTY.
Steps to reproduce (I used an imx7d):
1. generate regular bursts of messages
2. send a RTR from flexcan with higher priority than burst messages every
1ms, e.g. cangen -I 0x100 -L 0 -g 1 -R can0
3. notice a lost message without notification after some seconds
When running an iperf in parallel this problem is occurring even more
frequently. Using filters is not possible as at least one single CAN-ID
is allowed. Handling the TX MB during RX is also not possible as there
is no race-free disable of RX MB.
There is still a slight window when the described problem can occur. But
for that all RX MB must be in use which is essentially next to an
overrun. Still there will be no indication if it ever occurs.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pankaj Bansal [Wed, 1 Aug 2018 14:06:46 +0000 (19:36 +0530)]
can: flexcan: Unlock the MB unconditionally
Unlock the MB irrespective of reception method being FIFO or timestamp
based. It is optional but recommended to unlock Mailbox as soon as
possible and make it available for reception.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Lukas Wunner [Sat, 27 Oct 2018 08:36:54 +0000 (10:36 +0200)]
can: hi311x: Use level-triggered interrupt
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fabrizio Castro [Mon, 10 Sep 2018 10:43:14 +0000 (11:43 +0100)]
dt-bindings: can: rcar_can: Add r8a774a1 support
Document RZ/G2M (r8a774a1) SoC specific bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fabrizio Castro [Mon, 10 Sep 2018 10:43:13 +0000 (11:43 +0100)]
can: rcar_can: Fix erroneous registration
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes:
862e2b6af9413b43 ("can: rcar_can: support all input clocks")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Eugeniu Rosca [Mon, 20 Aug 2018 14:49:10 +0000 (16:49 +0200)]
dt-bindings: can: rcar_can: document r8a77965 support
Document the support for rcar_can on R8A77965 SoC devices.
Add R8A77965 to the list of SoCs which require the "assigned-clocks" and
"assigned-clock-rates" properties (thanks, Sergei).
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
YueHaibing [Wed, 29 Aug 2018 01:25:45 +0000 (01:25 +0000)]
can: ucan: remove duplicated include from ucan.c
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
YueHaibing [Wed, 29 Aug 2018 01:46:54 +0000 (01:46 +0000)]
can: ucan: remove set but not used variable 'udev'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
struct usb_device *udev;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jimmy Assarsson [Mon, 6 Aug 2018 13:14:49 +0000 (15:14 +0200)]
can: kvaser_usb: Fix accessing freed memory in kvaser_usb_start_xmit()
The call to can_put_echo_skb() may result in the skb being freed. The skb
is later used in the call to dev->ops->dev_frame_to_cmd().
This is avoided by moving the call to can_put_echo_skb() after
dev->ops->dev_frame_to_cmd().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jimmy Assarsson [Mon, 6 Aug 2018 13:14:50 +0000 (15:14 +0200)]
can: kvaser_usb: Fix potential uninitialized variable use
If alloc_can_err_skb() fails, cf is never initialized.
Move assignment of cf inside check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Wed, 24 Oct 2018 08:27:12 +0000 (10:27 +0200)]
can: raw: check for CAN FD capable netdev in raw_sendmsg()
When the socket is CAN FD enabled it can handle CAN FD frame
transmissions. Add an additional check in raw_sendmsg() as a CAN2.0 CAN
driver (non CAN FD) should never see a CAN FD frame. Due to the commonly
used can_dropped_invalid_skb() function the CAN 2.0 driver would drop
that CAN FD frame anyway - but with this patch the user gets a proper
-EINVAL return code.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Juergen Gross [Thu, 1 Nov 2018 12:33:07 +0000 (13:33 +0100)]
xen: remove size limit of privcmd-buf mapping interface
Currently the size of hypercall buffers allocated via
/dev/xen/hypercall is limited to a default of 64 memory pages. For live
migration of guests this might be too small as the page dirty bitmask
needs to be sized according to the size of the guest. This means
migrating a 8GB sized guest is already exhausting the default buffer
size for the dirty bitmap.
There is no sensible way to set a sane limit, so just remove it
completely. The device node's usage is limited to root anyway, so there
is no additional DOS scenario added by allowing unlimited buffers.
While at it make the error path for the -ENOMEM case a little bit
cleaner by setting n_pages to the number of successfully allocated
pages instead of the target size.
Fixes:
c51b3c639e01f2 ("xen: add new hypercall buffer mapping device")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Juergen Gross [Thu, 8 Nov 2018 07:35:06 +0000 (08:35 +0100)]
xen: fix xen_qlock_wait()
Commit
a856531951dc80 ("xen: make xen_qlock_wait() nestable")
introduced a regression for Xen guests running fully virtualized
(HVM or PVH mode). The Xen hypervisor wouldn't return from the poll
hypercall with interrupts disabled in case of an interrupt (for PV
guests it does).
So instead of disabling interrupts in xen_qlock_wait() use a nesting
counter to avoid calling xen_clear_irq_pending() in case
xen_qlock_wait() is nested.
Fixes:
a856531951dc80 ("xen: make xen_qlock_wait() nestable")
Cc: stable@vger.kernel.org
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Juergen Gross <jgross@suse.com>
Ming Lei [Mon, 29 Oct 2018 12:57:19 +0000 (20:57 +0800)]
block: make sure writesame bio is aligned with logical block size
Obviously the created writesame bio has to be aligned with logical block
size, and use bio_allowed_max_sectors() to retrieve this number.
Cc: stable@vger.kernel.org
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Xiao Ni <xni@redhat.com>
Cc: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Fixes:
b49a0871be31a745b2ef ("block: remove split code in blkdev_issue_{discard,write_same}")
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Mon, 29 Oct 2018 12:57:18 +0000 (20:57 +0800)]
block: cleanup __blkdev_issue_discard()
Cleanup __blkdev_issue_discard() a bit:
- remove local variable of 'end_sect'
- remove code block of 'fail'
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Xiao Ni <xni@redhat.com>
Cc: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Mon, 29 Oct 2018 12:57:17 +0000 (20:57 +0800)]
block: make sure discard bio is aligned with logical block size
Obviously the created discard bio has to be aligned with logical block size.
This patch introduces the helper of bio_allowed_max_sectors() for
this purpose.
Cc: stable@vger.kernel.org
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Xiao Ni <xni@redhat.com>
Cc: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Fixes:
744889b7cbb56a6 ("block: don't deal with discard limit in blkdev_issue_discard()")
Fixes:
a22c4d7e34402cc ("block: re-add discard_granularity and alignment checks")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Christoph Hellwig [Wed, 7 Nov 2018 08:20:25 +0000 (09:20 +0100)]
Revert "nvmet-rdma: use a private workqueue for delete"
This reverts commit
2acf70ade79d26b97611a8df52eb22aa33814cd4.
The commit never really fixed the intended issue and caused all
kinds of other issues, including a use before initialization.
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sagi Grimberg [Fri, 2 Nov 2018 18:22:13 +0000 (11:22 -0700)]
nvme: make sure ns head inherits underlying device limits
Whenever we update ns_head info, we need to make sure it is still
compatible with all underlying backing devices because although nvme
multipath doesn't have any explicit use of these limits, other devices
can still be stacked on top of it which may rely on the underlying limits.
Start with unlimited stacking limits, and every info update iterate over
siblings and adjust queue limits.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sagi Grimberg [Fri, 2 Nov 2018 23:12:21 +0000 (16:12 -0700)]
nvmet: don't try to add ns to p2p map unless it actually uses it
Even without CONFIG_P2PDMA this results in a error print:
nvmet: no peer-to-peer memory is available that's supported by rxe0 and /dev/nullb0
Fixes:
c6925093d0b2 ("nvmet: Optionally use PCI P2P memory")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 9 Nov 2018 12:30:44 +0000 (06:30 -0600)]
Merge tag 's390-4.20-2' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- A fix for the pgtable_bytes misaccounting on s390. The patch changes
common code part in regard to page table folding and adds extra
checks to mm_[inc|dec]_nr_[pmds|puds].
- Add FORCE for all build targets using if_changed
- Use non-loadable phdr for the .vmlinux.info section to avoid a
segment overlap that confuses kexec
- Cleanup the attribute definition for the diagnostic sampling
- Increase stack size for CONFIG_KASAN=y builds
- Export __node_distance to fix a build error
- Correct return code of a PMU event init function
- An update for the default configs
* tag 's390-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/perf: Change CPUM_CF return code in event init function
s390: update defconfigs
s390/mm: Fix ERROR: "__node_distance" undefined!
s390/kasan: increase instrumented stack size to 64k
s390/cpum_sf: Rework attribute definition for diagnostic sampling
s390/mm: fix mis-accounting of pgtable_bytes
mm: add mm_pxd_folded checks to pgtable_bytes accounting functions
mm: introduce mm_[p4d|pud|pmd]_folded
mm: make the __PAGETABLE_PxD_FOLDED defines non-empty
s390: avoid vmlinux segments overlap
s390/vdso: add missing FORCE to build targets
s390/decompressor: add missing FORCE to build targets
Juergen Gross [Wed, 7 Nov 2018 17:01:00 +0000 (18:01 +0100)]
x86/xen: fix pv boot
Commit
9da3f2b7405440 ("x86/fault: BUG() when uaccess helpers fault on
kernel addresses") introduced a regression for booting Xen PV guests.
Xen PV guests are using __put_user() and __get_user() for accessing the
p2m map (physical to machine frame number map) as accesses might fail
in case of not populated areas of the map.
With above commit using __put_user() and __get_user() for accessing
kernel pages is no longer valid. So replace the Xen hack by adding
appropriate p2m access functions using the default fixup handler.
Fixes:
9da3f2b7405440 ("x86/fault: BUG() when uaccess helpers fault on kernel addresses")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Stefan Wahren [Thu, 8 Nov 2018 19:38:26 +0000 (20:38 +0100)]
net: smsc95xx: Fix MTU range
The commit
f77f0aee4da4 ("net: use core MTU range checking in USB NIC
drivers") introduce a common MTU handling for usbnet. But it's missing
the necessary changes for smsc95xx. So set the MTU range accordingly.
This patch has been tested on a Raspberry Pi 3.
Fixes:
f77f0aee4da4 ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thor Thayer [Thu, 8 Nov 2018 17:42:14 +0000 (11:42 -0600)]
net: stmmac: Fix RX packet size > 8191
Ping problems with packets > 8191 as shown:
PING 192.168.1.99 (192.168.1.99) 8150(8178) bytes of data.
8158 bytes from 192.168.1.99: icmp_seq=1 ttl=64 time=0.669 ms
wrong data byte 8144 should be 0xd0 but was 0x0
16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f
20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
%< ---------------snip--------------------------------------
8112 b0 b1 b2 b3 b4 b5 b6 b7 b8 b9 ba bb bc bd be bf
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9 ca cb cc cd ce cf
8144 0 0 0 0 d0 d1
^^^^^^^
Notice the 4 bytes of 0 before the expected byte of d0.
Databook notes that the RX buffer must be a multiple of 4/8/16
bytes [1].
Update the DMA Buffer size define to 8188 instead of 8192. Remove
the -1 from the RX buffer size allocations and use the new
DMA Buffer size directly.
[1] Synopsys DesignWare Cores Ethernet MAC Universal v3.70a
[section 8.4.2 - Table 8-24]
Tested on SoCFPGA Stratix10 with ping sweep from 100 to 8300 byte packets.
Fixes:
286a83721720 ("stmmac: add CHAINED descriptor mode support (V4)")
Suggested-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Nov 2018 03:38:19 +0000 (19:38 -0800)]
Merge branch 'qed-Slowpath-Queue-bug-fixes'
Denis Bolotin says:
====================
qed: Slowpath Queue bug fixes
This patch series fixes several bugs in the SPQ mechanism.
It deals with SPQ entries management, preventing resource leaks, memory
corruptions and handles error cases throughout the driver.
Please consider applying to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sagiv Ozeri [Thu, 8 Nov 2018 14:46:11 +0000 (16:46 +0200)]
qed: Fix potential memory corruption
A stuck ramrod should be deleted from the completion_pending list,
otherwise it will be added again in the future and corrupt the list.
Return error value to inform that ramrod is stuck and should be deleted.
Signed-off-by: Sagiv Ozeri <sagiv.ozeri@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Thu, 8 Nov 2018 14:46:10 +0000 (16:46 +0200)]
qed: Fix SPQ entries not returned to pool in error flows
qed_sp_destroy_request() API was added for SPQ users that need to
free/return the entry they acquired in their error flows.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Thu, 8 Nov 2018 14:46:09 +0000 (16:46 +0200)]
qed: Fix blocking/unlimited SPQ entries leak
When there are no SPQ entries left in the free_pool, new entries are
allocated and are added to the unlimited list. When an entry in the pool
is available, the content is copied from the original entry, and the new
entry is sent to the device. qed_spq_post() is not aware of that, so the
additional entry is stored in the original entry as p_post_ent, which can
later be returned to the pool.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin [Thu, 8 Nov 2018 14:46:08 +0000 (16:46 +0200)]
qed: Fix memory/entry leak in qed_init_sp_request()
Free the allocated SPQ entry or return the acquired SPQ entry to the free
list in error flows.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 9 Nov 2018 01:34:27 +0000 (17:34 -0800)]
inet: frags: better deal with smp races
Multiple cpus might attempt to insert a new fragment in rhashtable,
if for example RPS is buggy, as reported by 배석진 in
https://patchwork.ozlabs.org/patch/994601/
We use rhashtable_lookup_get_insert_key() instead of
rhashtable_insert_fast() to let cpus losing the race
free their own inet_frag_queue and use the one that
was inserted by another cpu.
Fixes:
648700f76b03 ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>