OSDN Git Service
Johannes Berg [Wed, 8 Jan 2014 16:45:07 +0000 (17:45 +0100)]
mac80211: release multiple ACs in uAPSD, fix more-data bug
When a response for PS-Poll or a uAPSD trigger frame is sent, the
more-data bit should be set according to 802.11-2012 11.2.1.5 h),
meaning that it should indicate more data on the relevant ACs
(delivery-enabled or nondelivery-enabled for uAPSD or PS-Poll.)
In, for example, the following scenario:
* 1 frame on VO queue (either in driver or in mac80211)
* at least 1 frame on VI queue (in the driver)
* both VO/VI are delivery-enabled
* uAPSD trigger frame received
The more-data flag to the driver would not be set, even though
it should be.
While fixing this, I noticed that we should really release frames
from multiple ACs where there's data buffered in the driver for
the corresponding TIDs.
To address all this, restructure the code a bit to consider all
ACs if we only release driver frames or only buffered frames.
This also addresses the more-data bug described above as now the
TIDs will all be marked as released, so the driver will have to
check the number of frames.
While at it, clarify some code and comments and remove the found
variable, replacing it with the appropriate sw/hw release check.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 9 Jan 2014 10:05:31 +0000 (11:05 +0100)]
mac80211: fix PS-Poll driver release TID
Using ffs() for the PS-Poll release TID is wrong, it will cause
frames to be released in order 0 1 2 3 4 5 6 7 instead of the
correct 7 6 5 4 3 0 2 1. Fix this by adding a new function that
implements "highest priority TID" properly.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avinash Patil [Thu, 9 Jan 2014 23:22:57 +0000 (15:22 -0800)]
ieee80211: add definition for TDLS wide band extended capability
Seventh bit of 8th byte of extended capabilities specifies wide
bandwidth support for TDLS links. Add this definition to ieee80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ujjal Roy [Thu, 9 Jan 2014 15:46:14 +0000 (21:16 +0530)]
cfg80211: add sanity check for retry limit in wext-compat
Block setting the wrong values through iwconfig retry
command. Add sanity checking before sending the retry
limit to the driver.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Thu, 9 Jan 2014 09:37:23 +0000 (11:37 +0200)]
cfg80211: Add a function to get the number of supported channels
Add a utility function to get the number of channels supported by
the device, and update the places in the code that need this data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[replace another occurrence in libertas, fix kernel-doc, fix bugs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 6 Jan 2014 21:24:00 +0000 (22:24 +0100)]
mac80211: remove channel_change_time
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Tue, 7 Jan 2014 11:11:41 +0000 (13:11 +0200)]
mac80211: allow to set smps mode to OFF in AP mode
In managed mode, we should not ask for OFF mode because the
power settings may still require DYNAMIC. In AP mode, this
should be allowed since the default settings is OFF and
AUTOMATIC is not allowed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 7 Jan 2014 15:23:24 +0000 (16:23 +0100)]
mac80211: clean up prepare_for_handlers() return value
Using an int with 0/1 is not very common, make the function
return a bool instead with the same values (false/true).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Tue, 7 Jan 2014 11:10:20 +0000 (13:10 +0200)]
mac80211: simplify code in ieee80211_prepare_and_rx_handle
No need to assign the return value of prepare_for_handlers
to a variable if the only usage is to test it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Tue, 7 Jan 2014 11:09:38 +0000 (13:09 +0200)]
mac80211: clean up garbage in comment
Not clear how this landed here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 6 Jan 2014 20:53:27 +0000 (21:53 +0100)]
mac80211_hwsim: fix a print message
The prefix should be mac80211_hwsim, not mac_80211_hwsim.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Thu, 19 Dec 2013 18:25:15 +0000 (10:25 -0800)]
mac80211: sync dtim_count to TSF
On starting a mesh or AP BSS, the interface dtim_count
countdown should match that of the driver TSF.
Signed-off-by: Thomas Pedersen <twpedersen@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ujjal Roy [Mon, 6 Jan 2014 16:26:11 +0000 (21:56 +0530)]
cfg80211: fix wext-compat for getting retry value
While getting the retry limit, wext-compat returns the value
without updating the flag for retry->flags is 0. Also in this
case, it updates long retry flag when short and long retry
value are unequal.
So, iwconfig never showing "Retry short limit" and showing
"Retry long limit" when both values are unequal.
Updated the flags and corrected the condition properly.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh [Fri, 20 Dec 2013 08:39:52 +0000 (16:39 +0800)]
mac80211: enable WME for peer mesh STA
Enable the WME for peer mesh STA so that the driver,
such as wcn36xx, will pick this up and enabling it in HW.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 6 Jan 2014 15:02:34 +0000 (16:02 +0100)]
mac80211: fix memory leak in register_hw() error path
Move the internal scan request allocation below the last
sanity check in ieee80211_register_hw() to avoid leaking
memory if the sanity check actually triggers.
Reported-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 6 Jan 2014 14:56:59 +0000 (15:56 +0100)]
mac80211: handle station TX latency allocation errors
When the station's TX latency data structures need to be
allocated, handle failures properly and also free all the
structures if there are any other problems.
Move the allocation code up so that allocation failures
don't trigger rate control algorithm calls.
Reported-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 6 Jan 2014 14:47:15 +0000 (15:47 +0100)]
mac80211: clean up netdev debugfs macros a bit
Clean up the file macros a bit and use that to remove the
unnecessary format function for the tkip MIC test file
that really is write-only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 1 Jan 2014 16:22:30 +0000 (17:22 +0100)]
nl80211: move vendor/testmode event skb functions out of ifdef
The vendor/testmode event skb functions are needed outside
the ifdef for vendor-specific events, so move them out.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 19 Dec 2013 09:47:48 +0000 (10:47 +0100)]
mac80211: add tracing for ieee80211_sta_set_buffered
This is useful for debugging issues with drivers using this
function (erroneously), so add tracing for the API call.
Change-Id: Ice9d7eabb8fecbac188f0a741920d3488de700ec
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 30 Dec 2013 22:12:37 +0000 (23:12 +0100)]
cfg80211/mac80211: correct qos-map locking
Since the RTNL can't always be held, use wdev/sdata locking for
the qos-map dereference in mac80211. This requires cfg80211 to
consistently lock it, which it was missing in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kyeyoon Park [Tue, 17 Dec 2013 07:04:43 +0000 (23:04 -0800)]
mac80211: Add support for QoS mapping
Implement set_qos_map() handler for mac80211 to enable QoS mapping
functionality.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kyeyoon Park [Tue, 17 Dec 2013 07:01:30 +0000 (23:01 -0800)]
cfg80211: Add support for QoS mapping
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.
The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 18 Dec 2013 13:43:31 +0000 (14:43 +0100)]
nl80211: support vendor-specific events
In addition to vendor-specific commands, also support vendor-specific
events. These must be registered with cfg80211 before they can be used.
They're also advertised in nl80211 in the wiphy information so that
userspace knows can be expected. The events themselves are sent on a
new multicast group called "vendor".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Mon, 16 Dec 2013 20:49:14 +0000 (21:49 +0100)]
mac80211: add helper functions for tracking P2P NoA state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 18 Dec 2013 08:43:33 +0000 (09:43 +0100)]
mac80211: fix iflist_mtx/mtx locking in radar detection
The scan code creates an iflist_mtx -> mtx locking dependency,
and a few other places, notably radar detection, were creating
the opposite dependency, causing lockdep to complain. As scan
and radar detection are mutually exclusive, the deadlock can't
really happen in practice, but it's still bad form.
A similar issue exists in the monitor mode code, but this is
only used by channel-context drivers right now and those have
to have hardware scan, so that also can't happen.
Still, fix these issues by making some of the channel context
code require the mtx to be held rather than acquiring it, thus
allowing the monitor/radar callers to keep the iflist_mtx->mtx
lock ordering.
While at it, also fix access to the local->scanning variable
in the radar code, and document that radar_detect_enabled is
now properly protected by the mtx.
All this would now introduce an ABBA deadlock between the DFS
work cancelling and local->mtx, so change the locking there a
bit to not need to use cancel_delayed_work_sync() but be able
to just use cancel_delayed_work(). The work is also safely
stopped/removed when the interface is stopped, so no extra
changes are needed.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 18 Dec 2013 18:44:59 +0000 (19:44 +0100)]
mac80211: remove unnecessary iflist_mtx locking
The radar detection code changed a few times, and due to
the changes some iflist_mtx locking stayed in that isn't
actually necessary - remove it.
One version of the code needed it because an AP interface's
VLAN list was changed to use this, but then we moved the
list handling outside of the chanctx handling and thus the
locking was no longer needed.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Joe Perches [Thu, 19 Dec 2013 00:52:17 +0000 (16:52 -0800)]
mac80211: align struct ps_data.tim to unsigned long
Its address is used as an unsigned long *, so make sure
that the tim u8 array is properly aligned.
Signed-off-by: Joe Perches <joe@perches.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 18 Dec 2013 08:36:09 +0000 (09:36 +0100)]
mac80211: make ieee80211_recalc_radar_chanctx static
The function is only used in one file, so move it up a
bit to avoid forward declarations and make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Weilong Chen [Wed, 18 Dec 2013 07:44:16 +0000 (15:44 +0800)]
mac80211: fix checkpatch errors
Fix a number of different checkpatch errors.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Janusz Dziedzic [Thu, 5 Dec 2013 19:42:58 +0000 (20:42 +0100)]
nl80211: add VHT support for set_bitrate_mask
Add VHT MCS/NSS set support for nl80211_set_tx_bitrate_mask().
This should be used mainly for test purpose, to check
different MCS/NSS VHT combinations.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Max Stepanov [Sun, 8 Dec 2013 11:31:29 +0000 (13:31 +0200)]
mac80211: read station mgmt keys via get_key call
Allow to read management keys stored in a station's gtk key
array with a get_key function.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Max Stepanov [Sun, 8 Dec 2013 11:30:52 +0000 (13:30 +0200)]
mac80211: check pairwise key_idx on get_key call
Verify that a pairwise key index value on ieee80211_get_key call
doesn't exceed the boundaries of the pairwise key array.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Fri, 13 Dec 2013 19:13:51 +0000 (21:13 +0200)]
mac80211: align ieee80211_ibss_csa_beacon() with ieee80211_assign_beacon()
The return value of ieee80211_ibss_csa_beacon is not aligned with the
return value of ieee80211_assign_beacon(). For consistency and to be
able to use both functions with similar code, change
ieee80211_ibss_csa_beacon() not to send the bss changed notification
itself, but return what has changed so the caller can send the
notification instead.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Fri, 13 Dec 2013 19:13:50 +0000 (21:13 +0200)]
mac80211: refactor ieee80211_ibss_process_chanswitch()
Refactor ieee80211_ibss_process_chanswitch() to use
ieee80211_channel_switch() and avoid code duplication.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Sun, 15 Dec 2013 21:14:16 +0000 (13:14 -0800)]
mac80211: update adjusting TBTT bit in beacon
This regression was introduced in "mac80211: cache mesh
beacon".
mesh_sync_offset_adjust_tbtt() was assuming that the
beacon would be rebuilt in every single pre-tbtt
interrupt, but now the beacon update happens on the
workqueue, and it must be ready for immediate delivery to
the driver.
Save a pointer to the meshconf IE in the beacon_data (this
works because both the IE pointer and beacon buffer are
protected by the same rcu_{dereference,assign_pointer}())
for quick updates during pre-tbtt. This is faster and a
little prettier than iterating over the elements to find
the meshconf IE every time.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David Spinadel [Sun, 8 Dec 2013 19:48:57 +0000 (21:48 +0200)]
mac80211: reschedule sched scan after HW restart
Keep the sched scan req when starting sched scan, and reschedule
it in case of HW restart during sched scan.
The upper layer don't have to know about the restart.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Sun, 8 Dec 2013 07:42:25 +0000 (09:42 +0200)]
mac80211: make ieee80211_assign_beacon() static
This function is not used anywhere else than in cfg.c, so there's no
need to export it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luciano Coelho [Wed, 11 Dec 2013 18:39:46 +0000 (20:39 +0200)]
mac80211: lock sdata in ieee80211_csa_connection_drop_work()
We call ieee80211_ibss_disconnect(), which requires sdata to be
locked, so lock the sdata during ieee80211_csa_connection_drop_work().
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 14 Dec 2013 12:54:53 +0000 (13:54 +0100)]
mac80211: let the driver reserve extra tailroom in beacons
Can be used to add extra IEs (such as P2P NoA) without having to
reallocate the buffer.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 22:47:09 +0000 (23:47 +0100)]
mac80211: free all AP/VLAN keys at once
When the AP interface is stopped, free all AP and VLAN keys at
once to only require synchronize_net() once. Since that does
synchronize_net(), also move two such calls into the function
(using the new force_synchronize parameter) to avoid doing it
twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 22:18:37 +0000 (23:18 +0100)]
mac80211: optimise mixed AP/VLAN station removal
Teach sta_info_flush() to optionally also remove stations
from all VLANs associated with an AP interface to optimise
the station removal (in particular, synchronize_net().)
To not have to add the vlans argument throughout, do some
refactoring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 22:12:31 +0000 (23:12 +0100)]
mac80211: optimise synchronize_net() for sta_info_flush
There's no reason to have one synchronize_net() for each
removed station, refactor the code slightly to have just
a single synchronize_net() for all stations.
Note that this is currently useless as hostapd removes
stations one by one and this coalescing never happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 22:05:45 +0000 (23:05 +0100)]
mac80211: move synchronize_net() before sta key removal
There's no reason to do this inside the sta key removal
since the keys can only be reached through the sta (and
not by the driver at all) so once the sta can no longer
be reached, the keys are safe.
This will allow further optimisation opportunities with
multiple stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 21:46:11 +0000 (22:46 +0100)]
mac80211: don't delay station destruction
If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.
This should speed up some scenarios like hostapd shutdown.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 19:11:06 +0000 (20:11 +0100)]
mac80211: move 4-addr sta pointer clearing before synchronize_rcu()
The pointer should be cleared before synchronize_rcu() so that the
consequently dead station won't be found by any lookups in the TX
or RX paths.
Also check that the station is actually the one being removed, the
check is not needed because each 4-addr VLAN can only have a single
station and non-4-addr VLANs always have a NULL pointer there, but
the code is clearer this way (and we avoid the memory write.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 21:39:17 +0000 (22:39 +0100)]
iwlwifi: mvm: use pre-RCU-sync sta removal operation
iwlmvm relies on the current mac80211 behaviour of allowing
station pointers to be valid for an RCU grace period after
returning from the sta_state() callback. To optimise these
cases, this behaviour is going away, so make the driver use
the new sta_pre_rcu_remove() method to clear the pointer in
the fw_id_to_mac_id[] array.
Since this may happen while the station is still present in
the firmware, don't set the pointer to NULL but to -ENOENT
to mark this particular case. In client mode, the station
is kept even longer (until marking the MAC as unassociated)
so the drain flow must take this new behavior into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 4 Dec 2013 21:39:17 +0000 (22:39 +0100)]
mac80211: add pre-RCU-sync sta removal driver operation
Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.
Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.
This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.
The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 16 Dec 2013 10:23:45 +0000 (11:23 +0100)]
Merge remote-tracking branch 'wireless-next/master' into mac80211-next
Lorenzo Bianconi [Mon, 9 Dec 2013 22:37:49 +0000 (23:37 +0100)]
ath9k: initialize retry chain flags in tx99 code
Initialize first chain flags in ath9k_build_tx99_skb() according to
configured channel mode and channel width
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Mon, 9 Dec 2013 20:28:32 +0000 (22:28 +0200)]
MAINTAINERS: remove myself as maintainer of TI WiLink drivers
I don't have the time to maintain the TI WiLink WLAN drivers anymore.
Remove my name and mark them as Orphan.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Sat, 7 Dec 2013 02:17:40 +0000 (02:17 +0000)]
ath5k: Reset Tx interrupt bits also on PISR
Some cards don't update the PISR properly when all SISR bits
for Tx interrupts are being cleared and as a result we get
interrupt storm. Since we handle all tx queues all together
(so we don't really use the SISR bits to do per-queue interrupt
handling), we can manualy update PISR by doing a write-to-clear
on its Tx interrupt bits.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Kirsher [Fri, 6 Dec 2013 16:56:16 +0000 (08:56 -0800)]
nfc: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
CC: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Kirsher [Fri, 6 Dec 2013 11:32:14 +0000 (03:32 -0800)]
rfkill: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Kirsher [Fri, 6 Dec 2013 11:32:13 +0000 (03:32 -0800)]
drivers/net/wireless: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Christian Lamparter <chunkeey@googlemail.com>
CC: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Kirsher [Fri, 6 Dec 2013 11:32:12 +0000 (03:32 -0800)]
prism54: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: "Luis R. Rodriguez" <mcgrof@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Kirsher [Fri, 6 Dec 2013 11:32:11 +0000 (03:32 -0800)]
rt2x00: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Ivo van Doorn <IvDoorn@gmail.com>
CC: Gertjan van Wingerde <gwingerde@gmail.com>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Kirsher [Fri, 6 Dec 2013 11:32:10 +0000 (03:32 -0800)]
zd1211rw: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Daniel Drake <dsd@gentoo.org>
CC: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 11 Dec 2013 15:54:41 +0000 (10:54 -0500)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
John W. Linville [Wed, 11 Dec 2013 15:49:24 +0000 (10:49 -0500)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
Johan Hedberg [Tue, 10 Dec 2013 08:52:48 +0000 (10:52 +0200)]
Bluetooth: Fix handling of L2CAP Command Reject over LE
If we receive an L2CAP command reject message over LE we should take
appropriate action on the corresponding channel. This is particularly
important when trying to interact with a remote pre-4.1 system using LE
CoC signaling messages. If we don't react to the command reject the
corresponding socket would not be notified until a connection timeout
occurs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:54 +0000 (16:28 +0530)]
ath9k: Apply tuning caps for AR9330 and AR9485
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:53 +0000 (16:28 +0530)]
ath9k: Fix internal regulator for AR955x
The internal regulator needs to be programmed
correctly for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:52 +0000 (16:28 +0530)]
ath9k: Enable manual peak calibration for AR9331 v1.1
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:51 +0000 (16:28 +0530)]
ath9k: Remove AR9330 v1.0 macro as it's not supported
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:50 +0000 (16:28 +0530)]
ath9k: Fix regulatory compliance
Adjusting the CCA registers for maximum permissible
noise floor in ETSI/Japan domains has to be done for
all AR9003 family chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:49 +0000 (16:28 +0530)]
ath9k: Identify duplicate AR9565 v1.0 initvals
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:48 +0000 (16:28 +0530)]
ath9k: Identify duplicate AR9462 v2.0 initvals
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:47 +0000 (16:28 +0530)]
ath9k: Identify duplicate AR9485 initvals
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:46 +0000 (16:28 +0530)]
ath9k: Update high power gain table for AR9300
Now that the Buffalo-specific initvals have been
moved to a separate array, update the default high
power TX gain table for all AR9300 v2.2 devices.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:45 +0000 (16:28 +0530)]
ath9k: Use a separate TX gain table for WZR-HP-G450H
The Buffalo device WZR-HP-G450H uses the index 3 for TX gain,
which is set to the high_power table currently. Later variants
of the router use the same index, but instead refer to the
low_ob_db gain table. This is not handled in the driver since
there is no way to distinguish board revisions and the high_power
table is used (incorrectly) for the newer variants.
By default, devices based on AR9300 using the TX gain index 3 have
to use the high_power table. To make sure that WZR-HP-G450H is not
broken when the high_power table is updated, use a separate array
based on information obtained from the platform data.
The current situation where only the original variant of WZR-HP-G450H
works properly stays unchanged.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:44 +0000 (16:28 +0530)]
ath9k: Update AR9331 v1.2 initvals
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:43 +0000 (16:28 +0530)]
ath9k: Update AR9331 v1.1 initvals
* Update radio/baseband/gain tables.
* Mark ar9331_modes_high_power_tx_gain_1p1 as a duplicate
* ar9331_1p1_mac_postamble is not a duplicate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:42 +0000 (16:28 +0530)]
ath9k: Remove AR955x INI duplicates
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:41 +0000 (16:28 +0530)]
ath9k: Update mac_postamble for AR9003 family
Enable the ALWAYS_KEYSEARCH bit in the initvals. Currently
this is done in the driver, but adding this to the initvals
makes it easier to be in sync with the INI files given
by the systems engineering team.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:40 +0000 (16:28 +0530)]
ath9k: Initialize baseband for DFS channels
Certain baseband registers require different values
to be programmed when operating in a DFS channel to
ensure that radar detection works correctly. This
is required for AR9300, AR9340 and AR9580.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Fri, 6 Dec 2013 10:58:39 +0000 (16:28 +0530)]
ath9k: Add initval arrays for DFS channels
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 6 Dec 2013 04:07:12 +0000 (22:07 -0600)]
rtlwifi: rtl8192c-common: Fix sparse warning
Sparse reports the following:
CHECK drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:570:34: warning: dubious: !x & y
There should be a parens around the expression.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh [Fri, 6 Dec 2013 03:28:02 +0000 (11:28 +0800)]
wcn36xx: enable the beaconing in mesh mode
Enable the beaconing in wnc36xx by tweaking the tim offset and
force the use of AP-style beaconing. Otherwise, beaconing is not
working. The tim offset is set to 256. Otherwise, this will
overwrite mesh beacon submitted by mac80211.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh [Wed, 4 Dec 2013 10:46:54 +0000 (18:46 +0800)]
ath9k: enable dfs for mesh mode
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ujjal Roy [Tue, 3 Dec 2013 07:17:59 +0000 (23:17 -0800)]
mwifiex: do not flood kmsg/dmesg with USB debug messages
When TX data URB reaches high water mark the message
"data: -ENOSR is returned" is printed.
This is not an error case, so change it to debug print.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 3 Dec 2013 07:17:57 +0000 (23:17 -0800)]
mwifiex: remove redundant goto exit_remove statement
The check for 'priv' pointer is redundant. 'priv' won't
be used later in this routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ujjal Roy [Tue, 3 Dec 2013 07:17:56 +0000 (23:17 -0800)]
mwifiex: update statistics for bridged packets on AP interface
The bridged packets are updated to statistics on both TX and RX
paths. Also fix a typo in the comment.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ujjal Roy [Tue, 3 Dec 2013 07:17:55 +0000 (23:17 -0800)]
mwifiex: correct TX byte count statistics
The skb is modified in sending the TX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ujjal Roy [Tue, 3 Dec 2013 07:17:54 +0000 (23:17 -0800)]
mwifiex: correct RX byte count statistics
The skb is modified in processing the RX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ujjal Roy [Tue, 3 Dec 2013 07:17:53 +0000 (23:17 -0800)]
mwifiex: fix rx_pending count imbalance
RX packets are handled in different paths. Not all paths have
decrement of rx_pending counter. This patch fixes the counter
imbalance.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Tue, 3 Dec 2013 07:17:52 +0000 (23:17 -0800)]
mwifiex: avoid using variable name eth_hdr
eth_hdr is defined in kernel. Use a different variable name in
our functions.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 3 Dec 2013 07:17:51 +0000 (23:17 -0800)]
mwifiex: fix an issue with Appletalk devices
SNAP/LLC header in the AARP packet is being stripped off while
preparing an EthernetII header.
Annex M, Table M.3 in 802.11 spec says that some header
(ex. AppleTalk AARP(2)) should pass through untouched.
This patch modifies the check to exclude/include EthernetII
header translation for special cases.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 3 Dec 2013 07:17:50 +0000 (23:17 -0800)]
mwifiex: remove rfc1042_eth_hdr variable
Use 'rfc1042_header' available in net/wireless/util.c
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 3 Dec 2013 07:17:49 +0000 (23:17 -0800)]
mwifiex: declare snap_type as __be16 variable
Actually we are updating snap_type with h_proto (__be16 variable)
in ethernet frame header. Hence endianness conversion is not
required.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ujjal Roy [Tue, 3 Dec 2013 07:17:48 +0000 (23:17 -0800)]
mwifiex: use little-endian variables in firmware structures
The firmware expects the command structure members in little
endianness.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Mon, 2 Dec 2013 23:00:27 +0000 (08:00 +0900)]
bcma: pci: remove DEFINE_PCI_DEVICE_TABLE macro
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 9 Dec 2013 20:31:57 +0000 (15:31 -0500)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
John W. Linville [Mon, 9 Dec 2013 20:30:27 +0000 (15:30 -0500)]
Merge tag 'for-linville-
20131203' of git://github.com/kvalo/ath
Conflicts:
drivers/net/wireless/ath/ath10k/htc.c
drivers/net/wireless/ath/ath10k/mac.c
Emmanuel Grumbach [Tue, 3 Dec 2013 09:50:30 +0000 (11:50 +0200)]
iwlwifi: mvm: rs: fix compilation without CONFIG_MAC80211_DEBUGFS
This fixes compilation issues with CONFIG_MAC80211_DEBUGFS
not enabled.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Emmanuel Grumbach [Thu, 28 Nov 2013 12:58:20 +0000 (14:58 +0200)]
iwlwifi: mvm: BT Coex - enable Sync to SCO
Sync to SCO is a feature that allows to synchronise the
wifi activity with the predictable BT activity in
SCO profile. This allows to reduce the collisions and
improve overall quality.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira [Sun, 24 Nov 2013 19:30:13 +0000 (21:30 +0200)]
iwlwifi: mvm: rs: overhaul search cycle state machine
Rewrite the search cycle state machine to use a more data
oriented approach where the different Tx columns (configs)
limitations and next columns to search are reprsented in
tables which are easy to change. This overhaul also includes
several major fixes:
1. Prevent going back to a specific Tx column in a search
cycle if it was already explored.
2. Avoid switching to a Tx column that doesn't have any chance
if it performs perfectly to beat the current throughput we're
getting.
These issues were degrading throughput as they were causing
switching to "bad" Tx columns.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira [Thu, 28 Nov 2013 10:35:42 +0000 (12:35 +0200)]
iwlwifi: mvm: rs: use the proper channel width define for legacy rate
Use the 20Mhz channel width define instead of just the number
zero for legacy rates. Note that the define has the same value
so this is just a minor cleanup.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira [Thu, 28 Nov 2013 10:27:03 +0000 (12:27 +0200)]
iwlwifi: mvm: rs: fix mapping from HT/VHT rates to legacy
The table rs_ht_to_legacy is used to get the next legacy rate
following the last HT or VHT rate in the LQ rates table.
The mapping wasn't correct as well as didn't include entries
for MCS8/9 which led to out of bounds access. This didn't
trigger a crash but led to legacy rate entries using 1Mbps
rate.
In 5Ghz this probably caused the Tx to fail completely given
that Tx attempt would have reached the legacy entries and 1Mbps
isn't valid.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira [Thu, 28 Nov 2013 00:25:24 +0000 (02:25 +0200)]
iwlwifi: mvm: rs: set dual_stream_ant_msk to ANT_AB always
Drop code which was relevant when there were chips with
3 antennas. Setting to ANT_AB should be ok with all mvm
supported chips.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira [Fri, 22 Nov 2013 23:30:44 +0000 (01:30 +0200)]
iwlwifi: mvm: rs: remove unused parameter to rs_get_supported_rates
No use of the ieee80211 header. Drop it.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>