OSDN Git Service
Mauro Carvalho Chehab [Fri, 27 Nov 2009 15:55:21 +0000 (13:55 -0200)]
em28xx: don't reduce scale to half size for em2800
Since em2800 can't support 720x480 / 720x576, the driver used to reduce
the scale to half the size on those chips. As the proper fix were
applied, reducing the maximum horizontal resolution to 640, this hack
can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Fri, 27 Nov 2009 15:52:54 +0000 (13:52 -0200)]
em28xx: don't load audio modules when AC97 is mis-detected
With em2800 hardware, AC97 hardware can be detected even when it doesn't
exist. If, after probing for AC97, the driver won't find a companion
chip, simply prevents the load of the audio modules.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Fri, 27 Nov 2009 15:49:48 +0000 (13:49 -0200)]
em28xx: em2800 chips support max width of 640
Due to hardware limitation, em2800 chips can't work at resolutions
higher than 640x576, since the URB packet size is not enough.
The effect is that the image looses packages and shows a distortion
along the vertical axes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 21:48:54 +0000 (18:48 -0300)]
V4L/DVB (13523): dvb-bt8xx: fix compile warning
Fix this compile warning:
v4l/dvb-bt8xx.c: In function 'cx24108_tuner_set_params':
v4l/dvb-bt8xx.c:221: warning: array subscript is above array bounds
Make sure that we never get past the last element in the array.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 21:42:42 +0000 (18:42 -0300)]
V4L/DVB (13522): valj5jf8007s/t: fix compile warnings
Trivial fix for these bogus compile warnings:
v4l/va1j5jf8007s.c: In function 'va1j5jf8007s_tune':
v4l/va1j5jf8007s.c:394: warning: 'lock' may be used uninitialized in this function
v4l/va1j5jf8007t.c: In function 'va1j5jf8007t_tune':
v4l/va1j5jf8007t.c:273: warning: 'lock' may be used uninitialized in this function
v4l/va1j5jf8007t.c:273: warning: 'retry' may be used uninitialized in this function
These variables are never used uninitialized, but the compiler couldn't
figure that out unfortunately.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 21:39:31 +0000 (18:39 -0300)]
V4L/DVB (13521): dib8000: fix compile warning
Trivial fix for this bogus compile warning:
v4l/dib8000.c:958: warning: 'ncoeff' may be used uninitialized in this function
Note: ncoeff is never used uninitialized, but the compiler couldn't
figure that out.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 19:12:01 +0000 (16:12 -0300)]
V4L/DVB (13518): spec: regenerate videodev2.h.xml
After excluding .h.xml from the whitespace to tab conversion I had to
regenerate this xml file. The only changes here are whitespace changes.
If we change videodev2.h in the future, then videodev2.h.xml will only
show that same change and no more unrelated whitespace changes.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 15:47:02 +0000 (12:47 -0300)]
V4L/DVB (13509): pms: convert from V4L1 to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 15:37:00 +0000 (12:37 -0300)]
V4L/DVB (13508): pms: source code cleanup, use struct v4l2_device.
This prepares the pms driver for the v4l1 -> v4l2 conversion.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Wed, 25 Nov 2009 15:00:30 +0000 (12:00 -0300)]
V4L/DVB (13506): uvcvideo: Factorize common field in uvc_entity structure
The bNrInPins and baSourceID fields are common among all entities (some
of use bSourceID but this is conceptually the same). Move those two
fields out of entity type-specific unions into the uvc_entity structure
top level.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Wed, 25 Nov 2009 15:00:29 +0000 (12:00 -0300)]
V4L/DVB (13505): uvcvideo: Refactor chain scan
Don't handle the first output terminal in a chain in a special way. Use
uvc_scan_chain_entity() like for all other entities, making the chain
scan code more generic.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Wed, 25 Nov 2009 15:00:27 +0000 (12:00 -0300)]
V4L/DVB (13504): uvcvideo: Fix extension units parsing
The bNrInPins field is an 8 bit integer, not a 16 bit integer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Wed, 25 Nov 2009 15:00:22 +0000 (12:00 -0300)]
V4L/DVB (13503): uvcvideo: Merge iterms, oterms and units linked lists
All terminals and units are now added to a single linked list of
entities per chain. This makes terminals and units handling code more
generic.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Wed, 25 Nov 2009 14:15:56 +0000 (11:15 -0300)]
V4L/DVB (13502): uvcvideo: Add support for Genius eFace 2025 webcams
The Genius eFace 2025 (0458:706e) requires the MINMAX quirk. Add a
corresponding entry in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Gary Francis [Wed, 25 Nov 2009 06:03:31 +0000 (03:03 -0300)]
V4L/DVB (13500): pvrusb2: Fix lingering 16KB FX2 Firmware issues
These are additional fixes to enable proper pvrusb2 support of 16KB
sized FX2 firmware.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Wed, 25 Nov 2009 05:59:34 +0000 (02:59 -0300)]
V4L/DVB (13499): pvrusb2: Cosmetic tweak to minimize size_t exposure
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Wed, 25 Nov 2009 05:57:21 +0000 (02:57 -0300)]
V4L/DVB (13498): pvrusb2: Bind I2C address 0x71 for Zilog IR devices
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Wed, 25 Nov 2009 05:55:38 +0000 (02:55 -0300)]
V4L/DVB (13497): pvrusb2: Shorten device hardware description text to work around V4L shortcoming
The device text description in pvrusb2-devattr.c get mapped into a V4L
API string field that is unfortunately shorter than I expected. No
sense fighting City Hall here - this change shortens the descriptions
to fit the limit.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Wed, 25 Nov 2009 05:52:06 +0000 (02:52 -0300)]
V4L/DVB (13496): pvrusb2: Support manual extraction of 16KB FX2 firmware
This pvrusb2 change is in support of an existing feature used to help
identify and locate newer vendor supplied firmware. This change makes
the feature work for the newer larger firmware size.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Wed, 25 Nov 2009 05:49:21 +0000 (02:49 -0300)]
V4L/DVB (13495): pvrusb2: Support 16KB FX2 firmware
New FX2 firmware from Hauppauge is no longer 8KB in size - it's 16KB.
This is true for HVR-1950 and HVR-1900 devices. Without this change,
new pvrusb2 users with that hardware are unable to use the driver
(because the CD shipped with the hardware only has the 16KB firmware).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Igor M. Liplianin [Tue, 24 Nov 2009 23:16:04 +0000 (20:16 -0300)]
V4L/DVB (13493): TeVii S470 and TBS 6920 fixes
The new hardware design applied for this cards.
Silicon Labs
C8051F300 microcontroller is used for LNB power control.
It connected to cx23885 GPIO pins:
GPIO0 - P0.3 data
GPIO1 - P0.2 reset
GPIO2 - P0.1 clk
GPIO3 - P0.0 busy
Tevii S470 based on Montage Technology M88TS2020 digital satellite tuner
and M88DS3000 advanced DVB-S/S2 demodulator.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 24 Nov 2009 09:13:28 +0000 (06:13 -0300)]
V4L/DVB (13491): gspca - vc032x: Avoid crash on querymenu.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 24 Nov 2009 08:22:05 +0000 (05:22 -0300)]
V4L/DVB (13490): gspca - ov534: Add controls for sensor ov965x.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Mon, 23 Nov 2009 09:46:35 +0000 (06:46 -0300)]
V4L/DVB (13489): gspca - sonixj: Add the sensor po1030.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sun, 15 Nov 2009 08:21:09 +0000 (05:21 -0300)]
V4L/DVB (13488): gspca - ov534: Remove extra values at end of ov965x sequences.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sat, 14 Nov 2009 12:45:38 +0000 (09:45 -0300)]
V4L/DVB (13487): gspca - ov534: Add svga, xga and sxga modes for ov965x.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 17:30:53 +0000 (14:30 -0300)]
V4L/DVB (13480): atbm8830: fix compile warning
Fix this trivial compile warning:
v4l/atbm8830.c:164: warning: 'set_agc_config' defined but not used
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 17:29:33 +0000 (14:29 -0300)]
V4L/DVB (13479): cxusb: fix compile warning
Fix this trivial compile warning:
v4l/cxusb.c:1195: warning: unused variable 'n'
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 14:55:04 +0000 (11:55 -0300)]
V4L/DVB (13478): cx18: remove bogus init call.
The cx18 av core implemented an init call for no good reason. It's now
turned into an internal function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 9 Jun 2009 20:34:01 +0000 (17:34 -0300)]
V4L/DVB (13477): v4l2-subdev: remove unnecessary check
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 25 Nov 2009 14:27:16 +0000 (11:27 -0300)]
V4L/DVB (13476): spec: remove old dvb-spec and v4l2-spec directories
It was really confusing to have media-specs, v4l2-spec and dvb-spec.
So this patch removes v4l2-spec and dvb-spec. The docs in dvb-spec and
the V4L1_API.html file were moved to media-specs/old-docs.
Removed all references to v4l2-spec and dvb-spec.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Tue, 10 Nov 2009 16:14:51 +0000 (13:14 -0300)]
V4L/DVB (13471): v4l2 doc: Added FBUF_CAP_SRC_CHROMAKEY/FLAG_SRC_CHROMAKEY
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Tue, 10 Nov 2009 16:46:36 +0000 (13:46 -0300)]
V4L/DVB (13470): V4L2: Add Capability and Flag field for Chroma Key
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Tue, 10 Nov 2009 16:12:25 +0000 (13:12 -0300)]
V4L/DVB (13469): Davinci VPFE Capture: Add support for Control ioctls
Added support for Control IOCTL,
- s_ctrl
- g_ctrl
- queryctrl
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Mon, 9 Nov 2009 13:04:06 +0000 (10:04 -0300)]
V4L/DVB (13468): v4l2 doc: Added ROTATE and BG_COLOR control documentation
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Tue, 10 Nov 2009 16:32:53 +0000 (13:32 -0300)]
V4L/DVB (13467): V4L2: Added CID's V4L2_CID_ROTATE/BG_COLOR
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Mon, 9 Nov 2009 12:15:07 +0000 (09:15 -0300)]
V4L/DVB (13466): Davinci VPFE Capture:Replaced IRQ_VDINT1 with vpfe_dev->ccdc_irq1
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Mon, 9 Nov 2009 12:14:16 +0000 (09:14 -0300)]
V4L/DVB (13465): Davinci VPFE Capture: Take i2c adapter id through platform data
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Mon, 9 Nov 2009 12:13:20 +0000 (09:13 -0300)]
V4L/DVB (13464): Davinci VPFE Capture: add i2c adapter id in platform data
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vaibhav Hiremath [Mon, 9 Nov 2009 12:07:36 +0000 (09:07 -0300)]
V4L/DVB (13463): Davinci VPFE Capture: Specify device pointer in videobuf_queue_dma_contig_init
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 23 Nov 2009 17:14:26 +0000 (14:14 -0300)]
V4L/DVB (13460): v4l2-spec: add missing V4L2-PIX-FMT-STV0680 description.
[mchehab@redhat.com: fix the wrong videodev2.h.xml file]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pete Eberlein [Mon, 16 Nov 2009 18:07:42 +0000 (15:07 -0300)]
V4L/DVB (13455): go7007: Add struct v4l2_device.
This adds a struct v4l2_device to the go7007 device struct and registers
it during v4l2 initialization. The v4l2_device registration overwrites
the go->dev device_data, which is a struct usb_interface with intfdata set
to the struct go7007. This changes intfdata to point to the struct
v4l2_device inside struct go7007, which is what v4l2_device_register will
also set it to (and warn about non-null drvdata on register.) Since usb
disconnect can happen any time, this intfdata should always be present.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Fri, 13 Nov 2009 12:21:03 +0000 (09:21 -0300)]
V4L/DVB (13453): gspca - all subdrivers: Remove the unused frame ptr from pkt_scan().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Fri, 13 Nov 2009 11:16:02 +0000 (08:16 -0300)]
V4L/DVB (13452): gspca - main: Let the driver scan URB packets when no frame buffer.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Fri, 13 Nov 2009 10:38:16 +0000 (07:38 -0300)]
V4L/DVB (13451): gspca - main: Memorize the current frame buffer.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Fri, 13 Nov 2009 10:15:08 +0000 (07:15 -0300)]
V4L/DVB (13450): gspca - main: Clear the urb status before resubmit.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Thu, 12 Nov 2009 19:15:44 +0000 (16:15 -0300)]
V4L/DVB (13449): gspca - ov534: The AWB control works only when autogain is set.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Thu, 12 Nov 2009 18:59:27 +0000 (15:59 -0300)]
V4L/DVB (13448): gspca - main: Add a gspca flag for inactive controls.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 19:19:27 +0000 (16:19 -0300)]
V4L/DVB (13446): ivtv: Add more explicit detection of known IR devices for Hauppauge cards
Avoid legacy IR I2C probing for PVR-150, PVR-500, and PVR-350 cards. This
still probes, but restricts the possbile addresses probed per card.
Also removed legacy probe addresses for the KNC and PixelView cards which are
not supported by ivtv as far as I know.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 16:39:28 +0000 (13:39 -0300)]
V4L/DVB (13445): cx18: Use per cx18 instance init data for ir-kbd-i2c instead of const data
This change creates per cx18 instances of IR_i2c_init_data for handing over
initialization data to ir-kbd-i2c, since that module wants non-const data
even though it never modifies the data.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 15:52:34 +0000 (12:52 -0300)]
V4L/DVB (13444): ivtv: Add explicit IR controller initialization for the AVerTV M116
Add explicit support for the AVerTV M116 for use with the ir-kbd-i2c module.
This also eases future support for other AVerMedia ivtv boards with the same
microcontroller program at I2C address 0x40.
This is a reworked version of an earlier patch that was...
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 14:41:33 +0000 (11:41 -0300)]
V4L/DVB (13443): ivtv: Defer legacy I2C IR probing until after setup of known I2C devices
This avoids collisions of legacy IR controller probing with known I2C devices
in the card definitions in ivtv-cards.c. I2C driver modules for device listed
explicitly in a card definition should always take precedence over a probe
guessing where and IR controller may be.
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 04:47:45 +0000 (01:47 -0300)]
V4L/DVB (13442): ivtv: Add module parameter to adjust I2C SCL clock period per board
Add a module parameter to adjust I2C SCL clock period per board. This allows
some experimental fine tuning by end users to overcome quirky I2C device
problems.
Reported-by: "Aleksandr V. Piskunov" <aleksandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Aleksandr V. Piskunov [Sat, 21 Nov 2009 03:47:25 +0000 (00:47 -0300)]
V4L/DVB (13441): ivtv: Added FM radio support to Avermedia AVerTV MCE 116 Plus card
Signed-off-by: Aleksandr V. Piskunov <alexandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 21 Nov 2009 03:08:09 +0000 (00:08 -0300)]
V4L/DVB (13440): ivtv: Update the cards definitions to add another AVerMedia M113 variant
Add an AVerMedia M113 variant that was...
Reported-by: Hiemanshu Sharma <hiemanshu@fedoraproject.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antoine Jacquet [Fri, 20 Nov 2009 01:35:38 +0000 (22:35 -0300)]
V4L/DVB (13438): zr364xx: add support for Trust Powerc@m 910Z
Tested-by: Enrique Dominguez <enrique.pinos@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 11 Nov 2009 04:18:41 +0000 (01:18 -0300)]
V4L/DVB (13434): cx18: Bump version number due to significant buffer handling changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 11 Nov 2009 03:57:16 +0000 (00:57 -0300)]
V4L/DVB (13433): cx18: Remove duplicate list traversal when processing incoming MDLs
Update the incoming MDL's buffers' bytesused and sync the buffers for the cpu
in one pass instead of two.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 11 Nov 2009 03:22:57 +0000 (00:22 -0300)]
V4L/DVB (13432): cx18: Adjust encoder VBI MDL size to be exactly frame's worth of VBI data
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 11 Nov 2009 02:28:30 +0000 (23:28 -0300)]
V4L/DVB (13431): cx18: Adjust an MDL's final buffer size to force encoder transfer size
The encoder was not honoring the MDL size sent in DE_SET_MDL mailbox commands.
This change adjusts the size of the last buffer in an MDL, as reported to the
firmware, so that the encoder will send the exact amount of bytes we specify
per MDL transfer. This eliminates tearing in YUV playback when using
non-default YUV buffer sizes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 10 Nov 2009 02:55:30 +0000 (23:55 -0300)]
V4L/DVB (13430): cx18: Fix YUV capture so that encoder passes a single frame per transfer
Fix YUV capture such that the encoder will pass one frame per transfer. This
will allow the application to maintain frame alignment when a transfer from
the encoder is missed due to high system latency in service the CX23418 IRQ.
Also force YUV buffer sizes to be specified in multiples of 33.75 kB, the
smalled amount of buffer sizes need to store a complete set of HM12 4:2:0
macroblocks specifying 32 lines of the frame. A full 60Hz/525 line
screen requires 15 * 33.75 kB per frame and a full 50Hz/625 line screen
requires 18 * 33.75 kB per frame so the default buffer size is 3 * 33.75 kB,
requiring exactly 5 or 6 buffers per MDL respectively. The bytes needed per
frame and hence MDL need not be the bytes in an integer number of buffers.
However, if frame artifacts are seen with scaled screen sizes, the YUV buffer
size can be set 34 kB (33.75 kB) to get rid of the artifacts at the cost of more
copies between the kernel and userspace.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Mon, 9 Nov 2009 02:45:24 +0000 (23:45 -0300)]
V4L/DVB (13429): cx18: Add Memory Descriptor List (MDL) layer to buffer handling
Add a Memory Descriptor List (MDL) layer to buffer handling to implement
scatter-gather I/O. Currently there is still only 1 buffer per MDL.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Fri, 6 Nov 2009 00:51:24 +0000 (21:51 -0300)]
V4L/DVB (13428): cx18: Rename mdl_offset to mdl_base_idx or free_mdl_idx as appropriate
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Thu, 5 Nov 2009 02:13:58 +0000 (23:13 -0300)]
V4L/DVB (13427): cx18: Rename struct cx18_queue.buffers to struct cx18_queue.depth
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Thu, 5 Nov 2009 01:33:33 +0000 (22:33 -0300)]
V4L/DVB (13426): cx18: Rename struct cx18_mdl to struct cx18_mdl_ent
Rename type in anticipation of implementing a struct cx18_mdl type that
actually keeps track of a memory descriptor list.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Thu, 12 Nov 2009 09:13:41 +0000 (06:13 -0300)]
V4L/DVB (13425): gspca - ov534: Bad name of the ov965x 320x240 resolution.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Thu, 12 Nov 2009 09:10:36 +0000 (06:10 -0300)]
V4L/DVB (13424): gspca - ov534: Fix ov772x brightness and ov965x frame rate.
- the ov772x brightness was not setteble (fixed by M. Thrun)
- the set_frame_rate function does not work for ov965x
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Wed, 11 Nov 2009 17:28:53 +0000 (14:28 -0300)]
V4L/DVB (13423): gspca - ov534: More ov772x changes from Max Thrun.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Wed, 11 Nov 2009 10:46:28 +0000 (07:46 -0300)]
V4L/DVB (13422): gspca - ov534: ov772x changes from Richard Kaswy.
- 320x240 resolution added
- controls added
- different sd_desc tables
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 10 Nov 2009 17:49:43 +0000 (14:49 -0300)]
V4L/DVB (13421): gspca - main: Clearer message when bandwidth too small.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 10 Nov 2009 09:46:59 +0000 (06:46 -0300)]
V4L/DVB (13420): gspca - doc: Change the name of some webcams.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Mon, 9 Nov 2009 10:10:46 +0000 (07:10 -0300)]
V4L/DVB (13419): gspca - pac7302: Add debug register write interface.
Add debug register write interface to pac7302 to be able to set
for example the edge detect mode (bit 2 register 0x55) or the
test pattern (bit 0..3, register 0x72) and test overlay (bit 4,
register 0x72) from the user space. Only write of register
page 0 is supported by this patch.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Mon, 9 Nov 2009 10:08:04 +0000 (07:08 -0300)]
V4L/DVB (13418): gspca - pac7311: Stop sending URBs on first error.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonathan Corbet [Mon, 23 Nov 2009 17:29:35 +0000 (14:29 -0300)]
V4L/DVB (13417): Fix videobuf_queue_vmalloc_init() prototype
For whatever reason, the device structure pointer to
videobuf_queue_vmalloc_init is typed "void *", even though it's passed
right through to videobuf_queue_core_init(), which expects a struct
device pointer. The other videobuf implementations use struct device *;
I think vmalloc should too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sun, 22 Nov 2009 21:52:31 +0000 (18:52 -0300)]
V4L/DVB (13416): smssdio: initialize return value
The return value may be used uninitialized when the size parameter
happens to be 0.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sun, 22 Nov 2009 21:03:05 +0000 (18:03 -0300)]
V4L/DVB (13415): videobuf-core: explicitly cast page count
Explicitly cast page count in the debug message.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sat, 21 Nov 2009 16:46:12 +0000 (13:46 -0300)]
V4L/DVB (13414): ttusb-dec: do not overwrite the first part of phys string
Use strlcat() to append a string to the previously created first part.
The semantic match that finds this kind of problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression dev;
expression phys;
expression str;
expression size;
@@
usb_make_path(dev, phys, size);
- strlcpy(phys, str, size);
+ strlcat(phys, str, size);
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Julia Lawall [Sat, 21 Nov 2009 11:49:41 +0000 (08:49 -0300)]
V4L/DVB (13413): introduce missing kfree
Error handling code following a kzalloc should free the allocated data.
Similarly for usb-alloc urb.
The semantic match that finds the first problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Roel Kluin [Fri, 20 Nov 2009 18:34:13 +0000 (15:34 -0300)]
V4L/DVB: Fix test in copy_reg_bits()
The reg_pair2[j].reg was tested twice.
Cc: <stable@kernel.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Wed, 18 Nov 2009 19:01:34 +0000 (16:01 -0300)]
V4L/DVB (13410): firedtv: remove an unnecessary function argument
All read transactions initiated by firedtv are only quadlet-sized, hence
the backend->read call can be simplified a little.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Wed, 18 Nov 2009 19:01:14 +0000 (16:01 -0300)]
V4L/DVB (13409): firedtv: packet requeuing is likely to succeed
Packet DMA buffers are queued either initially all at once (then, a
queueing failure will cause firedtv to release the DMA context as a
whole) or subsequently one by one as they recycled after use (then a
failure is extremely unlikely). Therefore we can be a little less
cautious when counting at which packet buffer to set the interrupt flag.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Wed, 18 Nov 2009 19:00:55 +0000 (16:00 -0300)]
V4L/DVB (13408): firedtv: shrink buffer pointer table
Cache only addresses of whole pages, not of each buffer chunk. Besides,
page addresses can be obtained by page_address() instead of kmap() since
they were allocated in lowmem.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Igor M. Liplianin [Tue, 17 Nov 2009 01:22:32 +0000 (22:22 -0300)]
V4L/DVB (13407): Add Prof 7301 PCI DVB-S2 card
Add Prof 7301 PCI DVB-S2 card
The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Huang Weiyi [Thu, 12 Nov 2009 13:16:09 +0000 (10:16 -0300)]
V4L/DVB: pt1: remove duplicated #include
Remove duplicated #include('s) in
drivers/media/dvb/pt1/pt1.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Neukum [Mon, 9 Nov 2009 22:09:49 +0000 (19:09 -0300)]
V4L/DVB (13402): radio-mr800 - autosuspend for radio-mr800 driver
Patch adds autosuspend support for mr800 radio driver.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 8 Nov 2009 21:30:54 +0000 (18:30 -0300)]
V4L/DVB (13400): firedtv: port to new firewire core
The firedtv DVB driver will now work not only on top of the old ieee1394
driver stack but also on the new firewire driver stack.
Alongside to the firedtv-1394.c backend for driver binding and I/O, the
firedtv-fw.c backend is added. Depending on which of the two 1394
stacks is configured, one or the other or both backends will be built
into the firedtv driver.
This has been tested with a DVB-T and a DVB-C box on x86-64 and x86-32
together with a few different controllers (Agere FW323, a NEC chip, TI
TSB82AA2, TSB43AB22/A, VIA VT6306).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 8 Nov 2009 21:29:41 +0000 (18:29 -0300)]
V4L/DVB (13399): firedtv: add missing include, rename a constant
Add #include <dvb_demux.h> for dvb_dmx_swfilter_packets(). This was
already indirectly included via firedtv.h, but don't rely on it.
The 4 bytes which were referred to as FIREWIRE_HEADER_SIZE are actually
the source packet header from IEC 61883-4 (MPEG2-TS data transmission
over 1394), not e.g. the IEEE 1394 isochronous packet header. So choose
a more precise name.
Also, express the payload size as a preprocessor constant too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 8 Nov 2009 21:29:08 +0000 (18:29 -0300)]
V4L/DVB (13398): firedtv: reform lock transaction backend call
Preparation for the port of firedtv to the firewire-core kernel API:
The fdtv->backend->lock() hook and thus the CMP code is slightly changed
to better fit with the new API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 8 Nov 2009 21:28:45 +0000 (18:28 -0300)]
V4L/DVB (13397): firedtv: move remote control workqueue handling into rc source file
Preparation for the port of firedtv to the firewire-core kernel API:
Canceling of the remote control workqueue job is factored into
firedtv-rc.c. Plus trivial whitespace change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Julia Lawall [Sun, 8 Nov 2009 17:49:05 +0000 (14:49 -0300)]
V4L/DVB (13396): correct initialization of audio_mode
This initialization of the value of audio_mode is the one used if nothing
matches in the subsequent switch. The variable audio_mode is subsequently
assigned to constants such as TUNER_AUDIO_MONO and TUNER_AUDIO_STEREO.
TUNER_AUDIO_STEREO has the same value as V4L2_TUNER_MODE_STEREO, so it
would seem better to use that value here.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
hiranotaka@zng.jp [Sun, 8 Nov 2009 08:42:28 +0000 (05:42 -0300)]
V4L/DVB (13394): pt1: Support FE_READ_SNR
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marton Nemeth [Sun, 8 Nov 2009 07:41:28 +0000 (04:41 -0300)]
V4L/DVB (13389): gspca - pac7302: Handle return values in sd_start().
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marton Nemeth [Sun, 8 Nov 2009 07:35:12 +0000 (04:35 -0300)]
V4L/DVB (13388): gspca - pac7302: Add white balance control.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sat, 7 Nov 2009 19:38:55 +0000 (16:38 -0300)]
V4L/DVB (13387): gspca - main: Fix a compilation warning.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sat, 7 Nov 2009 18:30:50 +0000 (15:30 -0300)]
V4L/DVB (13386): gspca - main: Change version to 2.8.0.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sat, 7 Nov 2009 18:15:56 +0000 (15:15 -0300)]
V4L/DVB (13385): gspca - pac7302: Add red and blue balance control.
The valid values for these controls are 0..3 (lower two bits) which was
identified by trial and error on Labtec Webcam 2200 (USB ID 093a:2626).
The upper 6 bits are ignored on page 0, registers 0xc5 and 0xc7 by the camera.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sat, 7 Nov 2009 09:10:08 +0000 (06:10 -0300)]
V4L/DVB (13384): gspca - sonixj: Optimize code and add some comments.
- the i2c base address is now taken from the sn9c1xx register table
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sat, 7 Nov 2009 08:52:02 +0000 (05:52 -0300)]
V4L/DVB (13383): gspca - pac7311/pac7302: Propagate error to higher level software.
The usb_control_msg() can fail any time. Only continue writing
sequence if there was no error with the previous write. If there
was any problem stop sending URBs and propagate the error to the
gspca_main.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Sat, 7 Nov 2009 08:45:33 +0000 (05:45 -0300)]
V4L/DVB (13382): gspca - pac7302: Remove redundant stream off command.
The stream off command is sent to the device twice, one is enough.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Roel Kluin [Tue, 17 Nov 2009 22:43:40 +0000 (19:43 -0300)]
V4L/DVB (13380): sms-cards: make id unsigned in sms_get_board()
Make id signed so we can't get an invalid pointer when we pass a negative
id.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>