OSDN Git Service
Olof Johansson [Fri, 23 Jan 2015 22:44:16 +0000 (14:44 -0800)]
Merge tag 'imx-dt-3.20' of git://git./linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree changes for 3.20" from Shawn Guo:
The i.MX device tree update for 3.20:
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
* tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (28 commits)
ARM: dts: imx28-evk: remove duplicate property
ARM: vf610: use zero based naming for GPIO nodes
ARM: dts: imx6q: enable dma for ecspi5
ARM: dts: vfxxx: Add SNVS node
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: dts: imx6sx: add i.mx6sx sabreauto board support
ARM: dts: imx6sx-sdb: Add QSPI support
ARM: dts: imx6qdl: Remove OCRAM clock from VPU node
ARM: imx: apf51dev: add gpio-backlight support
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
ARM: i.MX53: dts: add sahara module
ARM: dts: imx6dl: correct cpufreq volt/freq table
ARM: dts: imx6q: update cpufreq volt/freq table
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Jan 2015 22:20:10 +0000 (14:20 -0800)]
Merge tag 'v3.20-next-dts2' of https://github.com/mbgg/linux-mediatek into next/dt
Merge "ARM: mediatek: DT changes for v3.20 (round 2)" from Matthias Brugger:
This adds uart support for mt6592 SoC.
* tag 'v3.20-next-dts2' of https://github.com/mbgg/linux-mediatek:
ARM: mediatek: dts: Add uart to mt6592
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Jan 2015 22:17:15 +0000 (14:17 -0800)]
Merge tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu/dt #2" from Andrew Lunn:
Second set of dt patches for mvebu for v3.20.
* tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
ARM: mvebu: fix compatible strings of MBus on Armada 375 and Armada 38x
dt: bindings: update mvebu-mbus DT binding with new compatible properties
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Jan 2015 22:06:25 +0000 (14:06 -0800)]
Merge tag 'v3.20-rockchip-dts1' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: soc updates for 3.20" [sic!] from Heiko Stübner:
dts part of core suspend support and limiting of rk3288
sd-card clockspeed to 150mhz
* tag 'v3.20-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add suspend settings for rk3288-evb-rk808
ARM: dts: rockchip: add RK3288 suspend support
ARM: dts: rockchip: set dw_mmc max-freq 150Mhz
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Jan 2015 21:58:01 +0000 (13:58 -0800)]
Merge tag 'bcm5301x-dt-2015-01-20' of https://github.com/hauke/linux into next/dt
Merge "ARM: BCM5301X: DT changes for v3.20" from Hauke Mehrtens:
bcm5301x-dt-2015-01-20: ARM: BCM5301X: dts updates for 3.20
* tag 'bcm5301x-dt-2015-01-20' of https://github.com/hauke/linux:
ARM: BCM5301X: Add DT for Buffalo WZR-900DHP
ARM: BCM5301X: Add LEDs for Buffalo devices
ARM: BCM5301X: Drop unused poll-interval from gpio-keys
ARM: BCM5301X: Add DT for Luxul XWC-1000
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Jan 2015 21:48:57 +0000 (13:48 -0800)]
Merge tag 'omap-for-v3.20/dt-pt2' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20, part 2" from Tony Lindgren:
More changes for omap dts files mostly to add support for
dm816x devices and clocks. Also adds a qspi device for
dra72x-evm.
* tag 'omap-for-v3.20/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra72-evm: Add qspi device
ARM: dts: Add minimal support for dm8168-evm
ARM: dts: Add basic clocks for dm816x
ARM: dts: Add basic dm816x device tree configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 22 Jan 2015 01:03:01 +0000 (17:03 -0800)]
Merge tag 'qcom-dt-for-3.20' of git://git./linux/kernel/git/galak/linux-qcom into next/dt
Merge "qcom DT changes for v3.20" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.20
* Correct IPQ8064 tlmm interrupt
* Add Support for SD Card Detect for ifc6410 board
* tag 'qcom-dt-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: Correct IPQ8064 tlmm interrupt
ARM: dts: qcom: Add Support for SD Card Detect for ifc6410 board
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 22 Jan 2015 01:00:47 +0000 (17:00 -0800)]
Merge tag 'renesas-dt2-for-v3.20' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v3.20" from Simon
Horman:
* Support Renesas memory controllers
* Add SRC interrupt number on r8a779~ and r8a7791 SoCs
* Fix MSTP8 input clocks on r8a7791 SoC
* Add PM domain support to r8a7740
* Add DT bindings for the R-Mobile System Controller
* Use Add sh73a0-specific FSI2 compatible property
* tag 'renesas-dt2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PM / Domains: R-Mobile SYSC: Document SH-Mobile AG5 (sh73a0) binding
ARM: shmobile: sh73a0 dtsi: Add memory-controller nodes
ARM: shmobile: r8a7740 dtsi: Add memory-controller node
ARM: shmobile: r8a73a4 dtsi: Add memory-controller nodes
ARM: shmobile: Add DT bindings for Renesas memory controllers
ARM: shmobile: r8a7791: add SRC interrupt number on DTSI
ARM: shmobile: r8a7790: add SRC interrupt number on DTSI
ARM: shmobile: r8a7791: fix MSTP8 input clocks
ARM: shmobile: r8a7740 dtsi: Add PM domain support
PM / Domains: Add DT bindings for the R-Mobile System Controller
ARM: shmobile: sh73a0 dtsi: Add SoC-specific FSI2 compatible property
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 22 Jan 2015 00:51:01 +0000 (16:51 -0800)]
Merge tag 'omap-for-v3.20/dt-pt1' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20" from Tony Lindgren:
Device tree changes for omaps. Mostly to add support for new
am437x-idk and update am437x-sk boards. Also enabling new
devices for multiple boards.
* tag 'omap-for-v3.20/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap3-gta04: Add handling for tv output
ARM: dts: cm-t3x: add NAND support
ARM: dts: am57xx-beagle-x15: Add GPIO controlled fan node
ARM: dts: am437x-idk: add gpio-based power key
ARM: dts: N950/N9: add twl_power
ARM: dts: am437x-sk: add power button binding
ARM: dts: add support for AM437x IDK
ARM: dts: am437x-gp-evm: add VPFE device tree data
ARM: dts: am437x-sk-evm: add VPFE device tree data
ARM: dts: am43x-epos-evm: add VPFE device tree data
ARM: dts: am4372: add VPFE DT node entries
ARM: dts: DRA7X: drop id property in pcie_phy
ARM: dts: omap3-n900: cleanup english
ARM: dts: am57xx-beagle-x15: Add dual ethernet
ARM: dts: am437x-sk: remove DSS pulls
ARM: dts: am437x-sk: remove internal i2c pullups
ARM: dts: am437x-sk: add explicit pinmux for both USB instances
ARM: dts: am437x-sk: remove ethernet pulls
ARM: dts: am437x-sk: add explicit MMC0 pinmux
ARM: dts: am437x-sk: remove internal pulls from QSPI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Paul Bolle [Mon, 19 Jan 2015 19:40:25 +0000 (20:40 +0100)]
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
The Kconfig symbol DEBUG_MVEBU_UART_ALTERNATE was renamed to
DEBUG_MVEBU_UART0_ALTERNATE. And the symbol DEBUG_MVEBU_UART1_ALTERNATE
was added to allow UART1 as a DEBUG_LL target. Make the comment at the
top of this DTS reflect those changes.
Since we're touching this DTS add comments to show which blocks describe
UART0 and UART1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Gregory CLEMENT [Thu, 15 Jan 2015 14:09:38 +0000 (15:09 +0100)]
ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
Add the regulators to each SATA port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Christoph Junghans [Wed, 14 Jan 2015 04:49:29 +0000 (21:49 -0700)]
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.
Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
[Andrew Lunn <andrew@lunn.ch>: Fixed subject line]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Olof Johansson [Wed, 21 Jan 2015 23:25:23 +0000 (15:25 -0800)]
Merge tag 'sti-dt-for-v3.20-1' of git://git.stlinux.com/devel/kernel/linux-sti into next/dt
Merge "STi DT updates for v3.20, round 1" from Maxime Coquelin:
Highlights:
-----------
- Add USB support for STiH410 & STiH407
- Add DRM DT nodes for STiH410 & STiH407
- Add STiH418 SoC support
- Add DT nodes for MiPHY28lp PHY
* tag 'sti-dt-for-v3.20-1' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: DT: STi: STiH407: Add DT node for MiPHY28lp
ARM: dts: STiH418: Add B2199 board support
ARM: dts: Add STiH418 SoC support
ARM: DT: STiH410: Add DRM dt nodes
ARM: DT: STiH407: Add DRM dt nodes
ARM: STi: DT: STiH410: Add DT nodes for the ehci and ohci usb controllers.
ARM: STi: DT: STiH410: Add usb2 picophy dt nodes
ARM: STi: DT: STiH407: Add usb2 picophy dt nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Wang Long [Wed, 24 Dec 2014 03:09:58 +0000 (03:09 +0000)]
ARM: dts: Add hip01-ca9x2 dts file
Add dts file for Hisilicon hip01 ca9x2 board
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
[olof: Folded in smp enable-method from a different patch]
Signed-off-by: Olof Johansson <olof@lixom.net>
Rafał Miłecki [Tue, 20 Jan 2015 21:42:16 +0000 (22:42 +0100)]
ARM: BCM5301X: Add DT for Buffalo WZR-900DHP
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Wed, 14 Jan 2015 07:20:49 +0000 (08:20 +0100)]
ARM: BCM5301X: Add LEDs for Buffalo devices
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Wed, 14 Jan 2015 07:20:48 +0000 (08:20 +0100)]
ARM: BCM5301X: Drop unused poll-interval from gpio-keys
It was accidentally left (& copied & pasted all around) from our
experiments with gpio-keys-polled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dan Haab [Mon, 19 Jan 2015 19:45:37 +0000 (12:45 -0700)]
ARM: BCM5301X: Add DT for Luxul XWC-1000
Luxul XWC-1000 is a controller device based on BCM4708 SoC. The only
unusual thing in its DTS file is "ubi" partition on NAND flash.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mugunthan V N [Mon, 19 Jan 2015 09:49:28 +0000 (15:19 +0530)]
ARM: dts: dra72-evm: Add qspi device
These add device tree entry for qspi device on dra72-evm.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Matthias Brugger [Wed, 14 Jan 2015 08:45:53 +0000 (09:45 +0100)]
ARM: mediatek: dts: Add uart to mt6592
This patch adds the uart ports and the uart clock to Mediateks
mt6592 SoC.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Michael Heimpold [Tue, 7 Oct 2014 21:00:39 +0000 (23:00 +0200)]
ARM: dts: imx28-evk: remove duplicate property
Seems to be a left-over from an automatic merge.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Stefan Agner [Fri, 16 Jan 2015 17:06:15 +0000 (18:06 +0100)]
ARM: vf610: use zero based naming for GPIO nodes
On Vybrid, all peripherals are numbered starting with zero,
including the GPIO and PORT module. However, the labels of the
corresponding device tree nodes start with one, which is confusing.
Fix that by renaming the labels of the gpio nodes in the device
tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Anton Bondarenko [Tue, 13 Jan 2015 18:04:08 +0000 (19:04 +0100)]
ARM: dts: imx6q: enable dma for ecspi5
Enable dma support for ecspi5 controller
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Olof Johansson [Tue, 20 Jan 2015 00:34:00 +0000 (16:34 -0800)]
Merge tag 'renesas-dt-cleanups2-for-v3.20' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Cleanups for v3.20" from Simon
Horman:
Second Round of Renesas ARM Based SoC DT Cleanups for v3.20
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
* tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7790: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7791 dtsi: Drop "renesas,rcar_sound" compatible value
ARM: shmobile: r8a7790 dtsi: Drop "renesas,rcar_sound" compatible value
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 20 Jan 2015 00:32:42 +0000 (16:32 -0800)]
ARM: dts: move alphascale in makefile
The file is roughly sorted alphabetically (with some exceptions where
old options have been split in two), so alphascale should go at the
top instead of at the bottom.
Also linewrap like other entries have been lately.
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 20 Jan 2015 00:30:48 +0000 (16:30 -0800)]
Merge branch 'asm/dt' into next/dt
* asm/dt:
add Alphascale to vendor-prefixes.txt
ARM: add alphascale,acc.txt bindings documentation
ARM: dts: add DT for Alphascale ASM9260 SoC
Oleksij Rempel [Thu, 8 Jan 2015 09:16:47 +0000 (10:16 +0100)]
add Alphascale to vendor-prefixes.txt
this company already provided some products, so it make sense to add
them to vendor-prefixes.txt list
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Oleksij Rempel [Thu, 8 Jan 2015 09:16:46 +0000 (10:16 +0100)]
ARM: add alphascale,acc.txt bindings documentation
ACC is for AlphaScale Clock Controller.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Oleksij Rempel [Thu, 8 Jan 2015 09:16:45 +0000 (10:16 +0100)]
ARM: dts: add DT for Alphascale ASM9260 SoC
for now it is wary basic SoC description with most important IPs needed
to make this device work
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tony Lindgren [Mon, 19 Jan 2015 19:47:35 +0000 (11:47 -0800)]
ARM: dts: Add minimal support for dm8168-evm
This allows booting the device with basic functionality.
Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.
Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:
http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 19 Jan 2015 19:47:35 +0000 (11:47 -0800)]
ARM: dts: Add basic clocks for dm816x
The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 19 Jan 2015 19:47:35 +0000 (11:47 -0800)]
ARM: dts: Add basic dm816x device tree configuration
Similar to other omap variants, let's add dm816x support.
Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Olof Johansson [Mon, 19 Jan 2015 19:21:25 +0000 (11:21 -0800)]
Merge tag 'at91-dt' of git://git./linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #1" from Nicolas Ferre:
First batch of DT changes for 3.20:
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: dts: sama5d3: add ov2640 camera sensor support
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
ARM: at91: dts: sama5d3: move the isi mck pin to mb
ARM: at91: dts: sama5d3: add missing pins of isi
ARM: at91: dts: sama5d3: split isi pinctrl
ARM: at91: dts: sama5d3: add isi clock
ARM: at91/dt: ethernut5: use at91sam9xe.dtsi
ARM: at91/dt: Add a dtsi for at91sam9xe
ARM: at91/dt: add SRAM nodes
ARM: at91/dt: at91rm9200ek: enable RTC
ARM: at91/dt: rm9200: add RTC node
ARM: at91/dt: at91sam9n12: Add RTC node
ARM: at91: sama5d4: Add SFR
ARM: at91: sama5d3: Add SFR
ARM: at91: Add Special Function Registers binding documentation
ARM: at91/dt: sam9263: Fix typo: ac91_clk -> ac97_clk
ARM: at91/dt: sama5d3: enable D2 as the heartbeat LED
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jan 2015 18:57:35 +0000 (10:57 -0800)]
Merge tag 'atlas7-init-dts-for-3.20' of git://git./linux/kernel/git/baohua/linux into next/dt
Merge "CSR atlas7 init dts for 3.20" from Barry Song:
Drop Marco and add init dts stuff for Atlas7
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
So we drop Marco dts stuff, and add dts stuff for Atlas7.
* tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: add init dts file for CSR atlas7 SoC
ARM: dts: drop MARCO platform DT stuff
Signed-off-by: Olof Johansson <olof@lixom.net>
Stephen Boyd [Fri, 5 Dec 2014 20:53:33 +0000 (12:53 -0800)]
ARM: dts: qcom: Correct IPQ8064 tlmm interrupt
The interrupt is 16, not 32 (which it would be if we include PPIs
in the count of interrupts).
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Tested-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pramod Gurav [Tue, 21 Oct 2014 05:53:19 +0000 (11:23 +0530)]
ARM: dts: qcom: Add Support for SD Card Detect for ifc6410 board
This changes muxes in gpio26 pin to function as gpio and adds support
for sd card detect for apq8064 based IFC6410 board.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Gabriel FERNANDEZ [Wed, 14 Jan 2015 09:54:00 +0000 (10:54 +0100)]
ARM: DT: STi: STiH407: Add DT node for MiPHY28lp
The MiPHY28lp is a Generic PHY which can serve various SATA, PCIe or
USB3 devices. The two first ports can be use for either; both SATA, both
PCIe or one of each in any configuration.
The Third port is only for USB3.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime COQUELIN [Fri, 9 Jan 2015 15:11:00 +0000 (16:11 +0100)]
ARM: dts: STiH418: Add B2199 board support
B2199 HDK is the reference board for STiH418 SoC.
It has the following characteristics:
- 3GB DDR3
- 8GB eMMC / SD-Card slot
- 32MB NOR Flash
- 1 x Gbit Ethernet
- 1 x USB3.0 port
- 2 x USB2.0 ports
- 1 x Sata or Mini-PCIe port
- 1 x WiFi 802.11ac (Quantenna)
- 1 x HDMI out
- 1 x HDMI in
- 1 x SPDIF
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime COQUELIN [Fri, 9 Jan 2015 15:11:00 +0000 (16:11 +0100)]
ARM: dts: Add STiH418 SoC support
The STiH418 is advanced UHD 60fps AVC processor with 3D graphic acceleration and
quad-core ARM Cortex A9 CPU.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Wed, 14 Jan 2015 15:47:00 +0000 (16:47 +0100)]
ARM: DT: STiH410: Add DRM dt nodes
This patch adds the DRM/KMS dt nodes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Gabriel FERNANDEZ [Wed, 14 Jan 2015 15:47:00 +0000 (16:47 +0100)]
ARM: DT: STiH407: Add DRM dt nodes
This patch adds the DRM/KMS dt nodes.
This node can't be in stih407-family.dtsi file because in the future we
will integrate a new stih418-b2199 board. It's a stih407 family board
with different drm/kms dt nodes.
That is why i created the stih407.dtsi file.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Geert Uytterhoeven [Wed, 14 Jan 2015 12:11:19 +0000 (13:11 +0100)]
PM / Domains: R-Mobile SYSC: Document SH-Mobile AG5 (sh73a0) binding
SH-Mobile AG5 (sh73a0) can be handled by the existing bindings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Josh Wu [Wed, 14 Jan 2015 02:41:54 +0000 (10:41 +0800)]
ARM: at91: dts: sama5d3: add ov2640 camera sensor support
According to v4l2 dt document, we add:
a camera host: ISI port.
a i2c camera sensor: ov2640 port.
to sama5d3xmb.dtsi.
The ov2640 node defines the pinctrls, clocks and refer to isi port.
The ISI node also has a reference to the ov2640 port.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Josh Wu [Sun, 4 Jan 2015 09:02:31 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and
used to provide MCK for camera sensor.
We change its name to: pinctrl_pck1_as_isi_mck.
As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin.
So we remove this pinctrl from ISI DT node. It will be added in sensor's
DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Josh Wu [Sun, 4 Jan 2015 09:02:30 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to
power-down or reset camera sensor.
So we should let camera sensor instead of ISI to configure the pins.
This patch will change pinctrl name from pinctrl_isi_{power,reset} to
pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's
DT node. We will add these two pinctrl to sensor's DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Bo Shen [Sun, 4 Jan 2015 09:02:29 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: move the isi mck pin to mb
The mck is decided by the board design, move it to mb related
dtsi file.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Bo Shen [Sun, 4 Jan 2015 09:02:28 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: add missing pins of isi
The ISI has 12 data lines, add the missing two data lines.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Bo Shen [Sun, 4 Jan 2015 09:02:27 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: split isi pinctrl
As the ISI has 12 data lines, however we only use 8 data lines with
sensor module. So, split the data line into two groups which make
it can be choosed depends on the hardware design.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Josh Wu [Sun, 4 Jan 2015 09:02:26 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: add isi clock
Add ISI peripheral clock in sama5d3.dtsi.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Tue, 13 Jan 2015 18:12:26 +0000 (19:12 +0100)]
ARM: at91/dt: ethernut5: use at91sam9xe.dtsi
The ethernut5 is actually based on an at91sam9xe, use the correct dts include.
Cc: Martin Reimann <martin.reimann@egnite.de>
Cc: Tim Schendekehl <tim.schendekehl@egnite.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Tue, 13 Jan 2015 18:12:25 +0000 (19:12 +0100)]
ARM: at91/dt: Add a dtsi for at91sam9xe
at91sam9xe is slightly different from at91sam9260, in particular it has a
different SRAM size and location.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Tue, 13 Jan 2015 18:12:24 +0000 (19:12 +0100)]
ARM: at91/dt: add SRAM nodes
Add nodes for the SRAM available on atmel SoCs
For the at91sam9260 and the at91sam9g20, address mirroring is used to create a
single contiguous SRAM range instead of declaring two separate banks.
Also remove leftover TODOs in the sam9g45 file
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: correct at91sam9rl sram size => 0x10000]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Tue, 13 Jan 2015 18:12:23 +0000 (19:12 +0100)]
ARM: at91/dt: at91rm9200ek: enable RTC
Enable the RTC on the at91rm9200ek.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Tue, 13 Jan 2015 18:12:22 +0000 (19:12 +0100)]
ARM: at91/dt: rm9200: add RTC node
Add a node for the RTC available on at91rm9200.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Tue, 13 Jan 2015 18:12:21 +0000 (19:12 +0100)]
ARM: at91/dt: at91sam9n12: Add RTC node
Add node for the RTC available on the at91sam9n12.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Thu, 18 Dec 2014 09:45:52 +0000 (10:45 +0100)]
ARM: at91: sama5d4: Add SFR
The sama4d4 has Special Function Registers that allow to manage DDR, OHCI, EBI
and AIC interrupt redirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Thu, 18 Dec 2014 09:45:51 +0000 (10:45 +0100)]
ARM: at91: sama5d3: Add SFR
The sama5d3 has Special Function Registers that allow to manage OHCI, EBI and
the UTMI clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni [Thu, 18 Dec 2014 09:45:50 +0000 (10:45 +0100)]
ARM: at91: Add Special Function Registers binding documentation
The special function registers gather some registers that allow to tweak
features provided by IPs controlled through another register range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexander Stein [Fri, 5 Dec 2014 14:16:55 +0000 (15:16 +0100)]
ARM: at91/dt: sam9263: Fix typo: ac91_clk -> ac97_clk
That clock should be called ac97_clk.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Josh Wu [Tue, 9 Dec 2014 10:54:46 +0000 (18:54 +0800)]
ARM: at91/dt: sama5d3: enable D2 as the heartbeat LED
This D2 led is available for all sama5d3x-ek board. So make it a
heartbeat LED.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Olof Johansson [Thu, 15 Jan 2015 01:12:44 +0000 (17:12 -0800)]
Merge tag 'mvebu-dt-3.20' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu: dt for v3.20" from Andrew Lunn:
mvebu dt changes for v3.20 (part #1)
- Add Armada 388 General Purpose Development Board support
- Add Device Tree description of the Armada 388 SoC
- Document the Device Tree binding for the Armada 388 SoC
- a38x: Add missing labels
- a38x: Add more pinctrl functions
- Add Armada 385 Access Point Development Board support
- Add a number of pinctrl functions
- A38x: Remove redundant pinctrl informations
- a38x: Fix node names
- Add support for Seagate BlackArmor NAS220
- kirkwood: enable phy driver for SATA controller on
88f6192
- gpio_poweroff support for Iomega ix2-200
- Use all remaining MTD space foor rootfs of Iomega ix2-200
* tag 'mvebu-dt-3.20' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add Armada 388 General Purpose Development Board support
ARM: mvebu: Add Device Tree description of the Armada 388 SoC
ARM: mvebu: Document the Device Tree binding for the Armada 388 SoC
ARM: mvebu: a38x: Add missing labels
ARM: mvebu: a38x: Add more pinctrl functions
ARM: mvebu: Add Armada 385 Access Point Development Board support
ARM: mvebu: Add a number of pinctrl functions
ARM: mvebu: A38x: Remove redundant pinctrl informations
ARM: mvebu: a38x: Fix node names
Kirkwood: add support for Seagate BlackArmor NAS220
ARM: dts: kirkwood: enable phy driver for SATA controller on
88f6192
ARM: dts: add gpio_poweroff support for Iomega ix2-200
ARM: dts: use all remaining MTD space foor rootfs of Iomega ix2-200
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Geert Uytterhoeven [Wed, 14 Jan 2015 11:13:02 +0000 (12:13 +0100)]
ARM: shmobile: sh73a0 dtsi: Add memory-controller nodes
Add device nodes for the two SDRAM Bus State Controllers.
The SBSCs are located in the A4BC0 resp. A4BC1 PM domains, which must
not be powered down, else the system will crash.
References to the A4BC0 and A4BC1 PM domains will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 14 Jan 2015 11:13:01 +0000 (12:13 +0100)]
ARM: shmobile: r8a7740 dtsi: Add memory-controller node
Add a device node for the DDR3 Bus State Controller (DBSC3).
The DBSC3 is located in the A4S PM domain, which must not be powered
down, else the system will crash.
This has no visible effect for now, as A4S was never turned off anyway
because its child PM domain A3SM contains the CPU core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 14 Jan 2015 11:13:00 +0000 (12:13 +0100)]
ARM: shmobile: r8a73a4 dtsi: Add memory-controller nodes
Add device nodes for the two DDR Bus State Controllers (DBSC).
The DBSCs are located in the A3BC PM domain, which must not be powered
down, else the system will crash.
A reference to the A3BC PM domain will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 14 Jan 2015 11:12:59 +0000 (12:12 +0100)]
ARM: shmobile: Add DT bindings for Renesas memory controllers
Add DT bindings for Renesas R-Mobile and SH-Mobile memory controllers.
Currently memory controller device nodes are used only to reference PM
domains, and prevent these PM domains from being powered down, which
would crash the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Olof Johansson [Tue, 13 Jan 2015 23:14:18 +0000 (15:14 -0800)]
Merge tag 'v3.20-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Merge "ARM: mediatek: DT changes for v3.20 (round 1)" from Matthias Brugger:
This adds support for the mediatek sysirq and the uarts for the following SoCs:
- mt8135
- mt8127
- mt6598
For mt6592 only the sysirq support was added.
* tag 'v3.20-next-dts' of https://github.com/mbgg/linux-mediatek:
ARM: mediatek: dts: Add uart to Aquaris5
ARM: mediatek: dts: Add uart to mt6589
dt-bindings: add mt6592 compatible string for mediatek sysirq
ARM: mediatek: Add sysirq device node to mt6592 dtsi
ARM: mediatek: dts: Add UART dts for MT8127 and MT8135 boards
DTS: serial: Add bindings document for the Mediatek UARTs
ARM: mediatek: add UART dts for mt8127 and mt8135
ARM: mediatek: Add sysirq in mt6589/mt8135/mt8127 dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Marek Belisko [Wed, 3 Dec 2014 21:33:22 +0000 (22:33 +0100)]
ARM: dts: omap3-gta04: Add handling for tv output
Add handling for gta04 tv out chain:
venc -> opa362 -> svideo
Use invert-polarity in venc node because opa362
is doing polarity inversion also.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 28 Dec 2014 14:30:49 +0000 (16:30 +0200)]
ARM: dts: cm-t3x: add NAND support
CM-T3517, CM-T3530 and CM-T3730 features NAND storage chip connected to
GPMC bus.
Add GPMC DT entry into the root DT file omap3-cm-t3x.dtsi, common for
all three modules.
NAND timings are calculated to be safe for CM-T3x devices as it works
now in non DT boot (in this case the timings are updated by U-Boot).
Update GPMC ranges in boards DT files to include all connected devices.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zhiwu Song [Thu, 25 Dec 2014 08:34:19 +0000 (16:34 +0800)]
ARM: dts: add init dts file for CSR atlas7 SoC
CSR atlas7 uses Network on Chip(NoC) bus architecture, there are dozens
of MARCOs, in each MARCO, there are dozens of hardware modules.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Sanchayan Maity [Wed, 7 Jan 2015 07:09:30 +0000 (12:39 +0530)]
ARM: dts: vfxxx: Add SNVS node
Add device tree node for the Secure Non-Volatile Storage
(SNVS) on the VF610 platform. The SNVS block also has a
Real Time Counter (RTC).
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Tue, 13 Jan 2015 11:17:50 +0000 (19:17 +0800)]
Merge branch 'imx/soc' into imx/dt
Sanchayan Maity [Wed, 7 Jan 2015 07:09:29 +0000 (12:39 +0530)]
ARM: imx: clk-vf610: Add clock for SNVS
Add support for clock gating of the SNVS peripheral.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Bhuvanchandra DV [Tue, 6 Jan 2015 13:36:56 +0000 (19:06 +0530)]
ARM: imx: clk-vf610: Add clock for UART4 and UART5
Add support for clock gating of UART4 and UART5.
We use these UART's in a (not yet mainlined)
device tree.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Kuninori Morimoto [Thu, 8 Jan 2015 01:55:27 +0000 (01:55 +0000)]
ARM: shmobile: r8a7791: add SRC interrupt number on DTSI
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Thu, 8 Jan 2015 01:55:15 +0000 (01:55 +0000)]
ARM: shmobile: r8a7790: add SRC interrupt number on DTSI
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Mon, 12 Jan 2015 22:31:14 +0000 (01:31 +0300)]
ARM: shmobile: r8a7791: fix MSTP8 input clocks
I made a mistake when rebasing Andrey Gusakov's patch adding MLB+ clock to the
R8A7791 device tree, inserting <&hp_clk> into the "clocks" property of the
MSTP8 node at a wrong position, so that the input clocks for MLB+ and IPMMU-SGX
got swapped...
Fixes:
7408d3061d2f ("ARM: shmobile: r8a7791: add MLB+ clock")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 3 Dec 2014 13:41:46 +0000 (14:41 +0100)]
ARM: shmobile: r8a7740 dtsi: Add PM domain support
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Add a minimal device node for the Coresight-ETM hardware block, and hook
it up to the D4 PM domain, so the R-Mobile System Controller driver can
keep the domain powered, until the new Coresight code handles runtime
PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Wed, 3 Dec 2014 13:41:41 +0000 (14:41 +0100)]
PM / Domains: Add DT bindings for the R-Mobile System Controller
The Renesas R-Mobile System Controller provides a.o. power management
support, following the generic PM domain bindings in
Documentation/devicetree/bindings/power/power_domain.txt.
For now this supports the R-Mobile A1 (r8a7740) only, but it should be
sufficiently generic to handle other members of the SH-Mobile/R-Mobile
family in the future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Wed, 17 Dec 2014 06:12:02 +0000 (06:12 +0000)]
ARM: shmobile: r8a7791: tidyup #sound-dai-cells settings
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Wed, 17 Dec 2014 06:11:52 +0000 (06:11 +0000)]
ARM: shmobile: r8a7790: tidyup #sound-dai-cells settings
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Tue, 6 Jan 2015 20:01:53 +0000 (21:01 +0100)]
ARM: shmobile: r8a7791 dtsi: Drop "renesas,rcar_sound" compatible value
The "renesas,rcar_sound" compatible property value was never processed
nor documented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven [Tue, 6 Jan 2015 20:01:52 +0000 (21:01 +0100)]
ARM: shmobile: r8a7790 dtsi: Drop "renesas,rcar_sound" compatible value
The "renesas,rcar_sound" compatible property value was never processed
nor documented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Olof Johansson [Tue, 13 Jan 2015 01:58:19 +0000 (17:58 -0800)]
Merge tag 'berlin-dt-for-3.20-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "ARM: berlin: DT changes for v3.20 (round 1)" from Sebastian Hesselbarth:
Berlin DT changes for v3.20 (round 1)
- add PMU nodes for BG2Q and BG2CD
- add PPI CPU masks for TWD timer interrupts
* tag 'berlin-dt-for-3.20-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add PPI cpu mask to twd timer interrupts
ARM: dts: berlin: add pmu node for BG2Q and BG2CD
Signed-off-by: Olof Johansson <olof@lixom.net>
Peter Robinson [Tue, 30 Dec 2014 06:20:27 +0000 (06:20 +0000)]
ARM: dts: Only build dtb if associated Arch and/or SoC is enabled
A number of arches (EXYNOS/IMX/TEGRA) are separated out into finer grained
definitions whether it be sub ARCH or SOC definitions. The device tree blobs
should only be built if the specific option is enabled that supports that
device or it might be that there's an expectation that the device is supported
when in actual fact it's not. This ensures only the relevant bits are built.
Also standardised the line break between the arch/soc definitions and the
dtbs to be on separate lines for better consistency as per feedback.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
[olof: Fixed stray \ in one of the IMX rules]
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 12 Jan 2015 22:24:07 +0000 (14:24 -0800)]
Merge tag 'renesas-dt-for-v3.20' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v3.20" from Simon Horman:
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
* tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
ARM: shmobile: r8a7791: add MLB+ clock
ARM: shmobile: r8a7790: add MLB+ clock
ARM: shmobile: ape6evm: Fix LAN9220 VDDVARIO voltage
ARM: shmobile: r8a73a4: Add r8a73a4-ape6evm.dtb to ARCH_SHMOBILE_MULTI
ARM: shmobile: ape6evm: Add keypad to the device tree
ARM: shmobile: ape6evm: Add LEDs to the device tree
ARM: shmobile: ape6evm: synchronize dts with reference platform
ARM: shmobile: ape6evm: fix compatible string for Ethernet controller
ARM: shmobile: r8a7794: Add MMCIF clock to device tree
ARM: shmobile: r8a7794: Add SDHI clocks to device tree
ARM: shmobile: r8a7794: Add I2C clocks to device tree
ARM: shmobile: r8a7779: Add TWD device to DTS
ARM: shmobile: r8a7779: Use MSTP for SCIF clocks
ARM: shmobile: r8a7779: Use R8A7779_CLK_P as SCIF parent clock
ARM: shmobile: r8a7794: Add QSPI clock to device tree
ARM: shmobile: lager: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add SYS-DMAC clocks to device tree
ARM: shmobile: r8a7791: Add IPMMU-SGX clock to device tree
ARM: shmobile: koelsch: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add USBDMAC[01] clocks to device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 12 Jan 2015 22:22:42 +0000 (14:22 -0800)]
Merge tag 'renesas-dt-cleanups-for-v3.20' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Cleanups for v3.20" from Simon Horman:
* Replace status value "ok" with "okay"
* tag 'renesas-dt-cleanups-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference dts: Replace status value "ok" by "okay"
ARM: shmobile: alt dts: Replace status value "ok" by "okay"
ARM: shmobile: koelsch dts: Replace status value "ok" by "okay"
ARM: shmobile: henninger dts: Replace status value "ok" by "okay"
ARM: shmobile: lager dts: Replace status value "ok" by "okay"
ARM: shmobile: armadillo800eva dts: Replace status value "ok" by "okay"
ARM: shmobile: genmai dts: Replace status value "ok" by "okay"
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sun, 11 Jan 2015 20:44:53 +0000 (12:44 -0800)]
linux 3.19-rc4
Linus Torvalds [Sun, 11 Jan 2015 20:44:10 +0000 (12:44 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Three small fixes from over the Christmas period, and wiring up the
new execveat syscall for ARM"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
ARM: 8249/1: mm: dump: don't skip regions
ARM: wire up execveat syscall
Matthias Brugger [Sat, 1 Aug 2015 10:03:00 +0000 (12:03 +0200)]
ARM: mediatek: dts: Add uart to Aquaris5
This patch enables uart port for the Aquaris5 mobile phone.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Matthias Brugger [Sat, 1 Aug 2015 10:03:00 +0000 (12:03 +0200)]
ARM: mediatek: dts: Add uart to mt6589
This patch adds the uart ports to the device tree of Mediatek mt6589 SoC.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Linus Torvalds [Sun, 11 Jan 2015 19:53:46 +0000 (11:53 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
with certain odd memory mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use asm volatile in __getcpu
x86/build: Clean auto-generated processor feature files
x86: Fix mkcapflags.sh bash-ism
x86: Fix step size adjustment during initial memory mapping
x86_64, vdso: Fix the vdso address randomization algorithm
Linus Torvalds [Sun, 11 Jan 2015 19:51:49 +0000 (11:51 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: group scheduling corner case fix, two deadline scheduler
fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
system fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
sched/deadline: Avoid double-accounting in case of missed deadlines
sched/deadline: Fix migration of SCHED_DEADLINE tasks
sched: Fix odd values in effective_load() calculations
sched, fanotify: Deal with nested sleeps
sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation
Linus Torvalds [Sun, 11 Jan 2015 19:47:45 +0000 (11:47 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
Linus Torvalds [Sun, 11 Jan 2015 19:46:31 +0000 (11:46 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"A liblockdep fix and a mutex_unlock() mutex-debugging fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Always clear owner field upon mutex_unlock()
tools/liblockdep: Fix debug_check thinko in mutex destroy
Konstantin Khlebnikov [Sun, 11 Jan 2015 13:54:06 +0000 (16:54 +0300)]
mm: fix corner case in anon_vma endless growing prevention
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit
7a3ef208e662 ("mm: prevent
endless growth of anon_vma hierarchy")
Anon_vma_clone() is usually called for a copy of source vma in
destination argument. If source vma has anon_vma it should be already
in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork(). In this case anon_vma_clone() finds
anon_vma for reusing.
Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that. As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.
This patch assigns ->anon_vma before calling anon_vma_clone().
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com>
Reported-and-tested-by: Oded Gabbay <oded.gabbay@amd.com>
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org # to match back-porting of 7a3ef208e662
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 11 Jan 2015 19:33:57 +0000 (11:33 -0800)]
mm: Don't count the stack guard page towards RLIMIT_STACK
Commit
fee7e49d4514 ("mm: propagate error from stack expansion even for
guard page") made sure that we return the error properly for stack
growth conditions. It also theorized that counting the guard page
towards the stack limit might break something, but also said "Let's see
if anybody notices".
Somebody did notice. Apparently android-x86 sets the stack limit very
close to the limit indeed, and including the guard page in the rlimit
check causes the android 'zygote' process problems.
So this adds the (fairly trivial) code to make the stack rlimit check be
against the actual real stack size, rather than the size of the vma that
includes the guard page.
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Cc: Jay Foad <jay.foad@gmail.com>
Cc: stable@kernel.org # to match back-porting of fee7e49d4514
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Barry Song [Sun, 4 Jan 2015 06:37:27 +0000 (14:37 +0800)]
ARM: dts: drop MARCO platform DT stuff
MARCO will not be supported any more. it has been replaced by CSR
atlas7.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Ingo Molnar [Sun, 11 Jan 2015 08:18:05 +0000 (09:18 +0100)]
Merge branch 'core/urgent' into locking/urgent, to collect all pending locking fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sat, 10 Jan 2015 20:23:03 +0000 (12:23 -0800)]
Merge tag 'vfio-v3.19-rc4' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Fix PCI header check in vfio_pci_probe() (Wei Yang)"
* tag 'vfio-v3.19-rc4' of git://github.com/awilliam/linux-vfio:
vfio-pci: Fix the check on pci device type in vfio_pci_probe()
Linus Torvalds [Sat, 10 Jan 2015 19:59:25 +0000 (11:59 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Just one fix: a qlogic busy wait regression"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
qla2xxx: fix busy wait regression