OSDN Git Service
Sebastian Reichel [Fri, 14 Jul 2023 01:37:43 +0000 (03:37 +0200)]
drm/panel: sitronix-st7789v: simplify st7789v_spi_write
st7789v_spi_write initializes a message with just
a single transfer, spi_sync_transfer can be used
for that.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-7-sre@kernel.org
Sebastian Reichel [Fri, 14 Jul 2023 01:37:42 +0000 (03:37 +0200)]
drm/panel: sitronix-st7789v: make reset GPIO optional
The reset pin might not be software controllable from the SoC,
so make it optional.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-6-sre@kernel.org
Sebastian Reichel [Fri, 14 Jul 2023 01:37:41 +0000 (03:37 +0200)]
drm/panel: sitronix-st7789v: remove unused constants
ST7789V_COLMOD_RGB_FMT_18BITS and ST7789V_COLMOD_CTRL_FMT_18BITS
are unused in favour of MIPI_DCS_PIXEL_FMT_18BIT, remove them.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-5-sre@kernel.org
Sebastian Reichel [Fri, 14 Jul 2023 01:37:40 +0000 (03:37 +0200)]
drm/panel: sitronix-st7789v: add SPI ID table
SPI device drivers should also have a SPI ID table.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-4-sre@kernel.org
Sebastian Reichel [Fri, 14 Jul 2023 01:37:39 +0000 (03:37 +0200)]
dt-bindings: display: st7789v: add Inanbo T28CP45TN89
Add compatible value for Inanbo t28cp45tn89 and make reset GPIO non
mandatory, since it might not be connected to the CPU.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-3-sre@kernel.org
Sebastian Reichel [Fri, 14 Jul 2023 01:37:38 +0000 (03:37 +0200)]
dt-bindings: vendor-prefixes: add Inanbo
Shenzhen INANBO Electronic Technology Co., Ltd. manufacturers TFT/OLED
LCD panels.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-2-sre@kernel.org
Arthur Grillo [Mon, 31 Jul 2023 18:22:41 +0000 (15:22 -0300)]
drm/tests: Alloc drm_device on drm_exec tests
The drm_exec tests where crashing[0] because of a null dereference. This
is caused by a new access of the `driver` attribute of `struct
drm_driver` on drm_gem_private_object_init(). Alloc the drm_device to
fix that.
[0]
[15:05:24] ================== drm_exec (6 subtests) ===================
[15:05:24] [PASSED] sanitycheck
^CERROR:root:Build interruption occurred. Cleaning console.
[15:05:50] [ERROR] Test: drm_exec: missing expected subtest!
[15:05:50] BUG: kernel NULL pointer dereference, address:
00000000000000b0
[15:05:50] #PF: supervisor read access in kernel mode
[15:05:50] #PF: error_code(0x0000) - not-present page
[15:05:50] PGD 0 P4D 0
[15:05:50] Oops: 0000 [#1] PREEMPT NOPTI
[15:05:50] CPU: 0 PID: 23 Comm: kunit_try_catch Tainted: G N
6.4.0-rc7-02032-ge6303f323b1a #69
[15:05:50] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc37 04/01/2014
[15:05:50] RIP: 0010:drm_gem_private_object_init+0x60/0xc0
Fixes:
e6303f323b1a ("drm: manager to keep track of GPUs VA mappings")
Signed-off-by: Arthur Grillo <arthurgrillo@riseup.net>
Tested-by: Danilo Krummrich <dakr@redhat.com>
Acked-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731182241.240556-1-arthurgrillo@riseup.net
Dmitry Osipenko [Thu, 23 Mar 2023 23:07:55 +0000 (02:07 +0300)]
drm/virtio: Support sync objects
Add sync object DRM UAPI support to VirtIO-GPU driver. Sync objects
support is needed by native context VirtIO-GPU Mesa drivers, it also will
be used by Venus and Virgl contexts.
Reviewed-by; Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com> # amdgpu nctx
Tested-by: Rob Clark <robdclark@gmail.com> # freedreno nctx
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Gurchetan Singh <gurchetansingh@chromium.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230416115237.798604-4-dmitry.osipenko@collabora.com
Thomas Zimmermann [Sat, 29 Jul 2023 19:26:49 +0000 (21:26 +0200)]
fbdev: Align deferred I/O with naming of helpers
Deferred-I/O generator macros generate callbacks for struct fb_ops
that operate on memory ranges in I/O address space or system address
space. Rename the macros to use the _IOMEM_ and _SYSMEM_ infixes of
their underlying helpers. Adapt all users. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230729193157.15446-5-tzimmermann@suse.de
Thomas Zimmermann [Sat, 29 Jul 2023 19:26:48 +0000 (21:26 +0200)]
fbdev: Use _DMAMEM_ infix for DMA-memory helpers
Change the infix for fbdev's DMA-memory helpers from _DMA_ to
_DMAMEM_. The helpers perform operations within DMA-able memory,
but they don't perform DMA operations. Naming should make this
clear. Adapt all users. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230729193157.15446-4-tzimmermann@suse.de
Thomas Zimmermann [Sat, 29 Jul 2023 19:26:47 +0000 (21:26 +0200)]
fbdev: Use _SYSMEM_ infix for system-memory helpers
Change the infix for fbdev's system-memory helpers from _SYS_ to
_SYSMEM_. The helpers perform operations within system memory, but
not on the state of the operating system itself. Naming should make
this clear. Adapt all users. No functional changes.
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230729193157.15446-3-tzimmermann@suse.de
Thomas Zimmermann [Sat, 29 Jul 2023 19:26:46 +0000 (21:26 +0200)]
fbdev: Use _IOMEM_ infix for I/O-memory helpers
Change the infix for fbdev's I/O-memory helpers from _IO_ to _IOMEM_
to distiguish them from other types of I/O, such as file operations.
The helpers operate on memory ranges in the I/O address space and the
naming should make this clear. Adapt all users. No functional changes.
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230729193157.15446-2-tzimmermann@suse.de
Marek Vasut [Sun, 9 Jul 2023 13:49:14 +0000 (15:49 +0200)]
drm/panel: simple: Add missing connector type and pixel format for AUO T215HVN01
The connector type and pixel format are missing for this panel,
add them to prevent various drivers from failing to determine
either of those parameters.
Fixes:
7ee933a1d5c4 ("drm/panel: simple: Add support for AUO T215HVN01")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230709134914.449328-1-marex@denx.de
Guillaume La Roque [Mon, 31 Jul 2023 15:08:57 +0000 (17:08 +0200)]
drm/panel: Support for startek-kd070fhfid015 MIPI-DSI panel
This driver support the Startek KD070FHFID015, which is a 7-inch TFT LCD
display using MIPI DSI interface.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230711-startek_display-v4-2-fb1d53bfdef6@baylibre.com
Alexandre Mergnat [Mon, 31 Jul 2023 15:08:56 +0000 (17:08 +0200)]
dt-bindings: display: panel: add startek kd070fhfid015 support
The Startek KD070FHFID015 is a 7-inch TFT LCD display with a resolution
of 1024 x 600 pixels.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230711-startek_display-v4-1-fb1d53bfdef6@baylibre.com
Matus Gajdos [Wed, 19 Jul 2023 10:26:15 +0000 (12:26 +0200)]
drm/panel: ilitek-ili9881c: Add TDO TL050HDV35 LCD panel
Add support for TDO TL050HDV35-H1311A LCD panel.
Signed-off-by: Matus Gajdos <matuszpd@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719102616.2259-3-matuszpd@gmail.com
Matus Gajdos [Wed, 19 Jul 2023 10:26:14 +0000 (12:26 +0200)]
dt-bindings: ili9881c: Add TDO TL050HDV35 LCD panel
Add support for TDO TL050HDV35-H1311A LCD panel.
Signed-off-by: Matus Gajdos <matuszpd@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719102616.2259-2-matuszpd@gmail.com
Dmitry Baryshkov [Thu, 27 Jul 2023 17:24:45 +0000 (20:24 +0300)]
drm: panel: simple: specify bpc for powertip_ph800480t013_idf02
Specify bpc value for the powertip_ph800480t013_idf02 panel to stop drm
code from complaining about unexpected bpc value (0).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727172445.1548834-1-dmitry.baryshkov@linaro.org
Arnd Bergmann [Wed, 19 Jul 2023 13:09:21 +0000 (15:09 +0200)]
drm/panel: r66451: select CONFIG_DRM_DISPLAY_DP_HELPER
The newly added driver only builds when DRM_DISPLAY_DP_HELPER is enabled:
x86_64-linux-ld: drivers/gpu/drm/panel/panel-visionox-r66451.o: in function `visionox_r66451_enable':
panel-visionox-r66451.c:(.text+0x105): undefined reference to `drm_dsc_pps_payload_pack'
Select both CONFIG_DRM_DISPLAY_DP_HELPER and CONFIG_DRM_DISPLAY_HELPER to
ensure the helper function is always available.
Fixes:
a6dfab2738fc ("drm/panel: Add driver for Visionox r66451 panel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719130940.659837-1-arnd@kernel.org
Maxime Ripard [Fri, 28 Jul 2023 09:06:24 +0000 (11:06 +0200)]
drm/vc4: tests: pv-muxing: Document test scenario
We've had a couple of tests that weren't really obvious, nor did they
document what they were supposed to test. Document that to make it
hopefully more obvious.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-11-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:23 +0000 (11:06 +0200)]
drm/vc4: tests: Switch to atomic state allocation helper
Now that we have a helper that takes care of an atomic state allocation
and cleanup, we can migrate to it to simplify our tests.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-10-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:22 +0000 (11:06 +0200)]
drm/vc4: tests: pv-muxing: Switch to managed locking init
The new helper to init the locking context allows to remove some
boilerplate.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-9-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:21 +0000 (11:06 +0200)]
drm/vc4: tests: mock: Use a kunit action to unregister DRM device
The *_mock_device functions allocate a DRM device that needs to be
released using drm_dev_unregister.
Now that we have a kunit release action API, we can switch to it and
don't require any kind of garbage collection from the caller.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-8-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:20 +0000 (11:06 +0200)]
drm/vc4: tests: pv-muxing: Remove call to drm_kunit_helper_free_device()
Calling drm_kunit_helper_free_device() to clean up the resources
allocated by drm_kunit_helper_alloc_device() is now optional and not
needed in most cases.
Remove it.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-7-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:19 +0000 (11:06 +0200)]
drm/tests: helpers: Create a helper to allocate an atomic state
As we gain more tests, boilerplate to allocate an atomic state and free
it starts to be there more and more as well.
In order to reduce the allocation boilerplate, we can create a helper
to create that atomic state, and call an action when the test is done.
This will also clean up the exit path.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-6-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:18 +0000 (11:06 +0200)]
drm/tests: helpers: Create a helper to allocate a locking ctx
As we get more and more tests, the locking context initialisation
creates more and more boilerplate, both at creation and destruction.
Let's create a helper that will allocate, initialise a context, and
register kunit actions to clean up once the test is done.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-5-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:17 +0000 (11:06 +0200)]
drm/tests: probe-helper: Remove call to drm_kunit_helper_free_device()
Calling drm_kunit_helper_free_device() to clean up the resources
allocated by drm_kunit_helper_alloc_device() is now optional and not
needed in most cases.
Remove it.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-4-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:16 +0000 (11:06 +0200)]
drm/tests: modes: Remove call to drm_kunit_helper_free_device()
Calling drm_kunit_helper_free_device() to clean up the resources
allocated by drm_kunit_helper_alloc_device() is now optional and not
needed in most cases.
Remove it.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-3-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:15 +0000 (11:06 +0200)]
drm/tests: client-modeset: Remove call to drm_kunit_helper_free_device()
Calling drm_kunit_helper_free_device() to clean up the resources
allocated by drm_kunit_helper_alloc_device() is now optional and not
needed in most cases.
Remove it.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-2-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Maxime Ripard [Fri, 28 Jul 2023 09:06:14 +0000 (11:06 +0200)]
drm/tests: helpers: Switch to kunit actions
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Link: https://lore.kernel.org/r/20230728-kms-kunit-actions-rework-v3-1-952565ccccfe@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Zhu Wang [Mon, 31 Jul 2023 02:13:45 +0000 (10:13 +0800)]
drm/bridge: fix -Wunused-const-variable= warning
When building with W=1, the following warning occurs.
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:48:17: warning: ‘anx781x_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx781x_i2c_addresses[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:40:17: warning: ‘anx7808_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx7808_i2c_addresses[] = {
When CONFIG_IO is disabled, above two variables are not used,
since the place where it is used is inclueded in the macro
CONFIG_OF.
Even for drivers that do not depend on CONFIG_OF, it's almost
always better to leave out the of_match_ptr(), since the only
thing it can possibly do is to save a few bytes of .text if a
driver can be used both with and without it. Hence we remove
all of_match_ptr() used in other places.
Fixes:
0647e7dd3f7a ("drm/bridge: Add Analogix anx78xx support")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731021345.219588-1-wangzhu9@huawei.com
Jiapeng Chong [Mon, 31 Jul 2023 07:49:27 +0000 (15:49 +0800)]
drm/ssd130x: clean up some inconsistent indenting
No functional modification involved.
drivers/gpu/drm/solomon/ssd130x.c:715 ssd130x_primary_plane_duplicate_state() warn: inconsistent indenting.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6034
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731074927.22755-1-jiapeng.chong@linux.alibaba.com
Geert Uytterhoeven [Wed, 19 Jul 2023 15:23:37 +0000 (17:23 +0200)]
drm: Fix references to drm_plane_helper_check_state()
As of commit
a01cb8ba3f628293 ("drm: Move drm_plane_helper_check_state()
into drm_atomic_helper.c"), drm_plane_helper_check_state() no longer
exists, but is part of drm_atomic_helper_check_plane_state().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8bb42a92fc20e3d11e5847e7f15a47c687b73104.1689779916.git.geert+renesas@glider.be
Geert Uytterhoeven [Wed, 19 Jul 2023 15:23:36 +0000 (17:23 +0200)]
drm: Remove references to removed transitional helpers
The transitional helpers were removed a long time ago, but some
references stuck. Remove them.
Fixes:
21ebe615c16994f3 ("drm: Remove transitional helpers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ad4a2f1f9fa7da083132f6c35469c77a3f9e2f0e.1689779916.git.geert+renesas@glider.be
Geert Uytterhoeven [Wed, 19 Jul 2023 15:23:35 +0000 (17:23 +0200)]
drm/todo: Convert list of fbconv links to footnotes
Convert the references to fbconv links to footnotes, so they can be
navigated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0761f98d3b6f8df9eea977eae063e35b450fda9e.1689779916.git.geert+renesas@glider.be
Geert Uytterhoeven [Wed, 19 Jul 2023 15:23:34 +0000 (17:23 +0200)]
drm/todo: Add atomic modesetting references
The section about converting existing KMS drivers to atomic modesetting
mentions the existence of a conversion guide, but does not reference it.
While the guide is old and rusty, it still contains useful information,
so add a link to it. Also link to the LWN.net articles that give an
overview about the atomic mode setting design.
While at it, remove the reference to unconverted virtual HW drivers, as
they've been converted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6809d0fda0716892cbccf0ee272481032251026d.1689779916.git.geert+renesas@glider.be
Geert Uytterhoeven [Thu, 17 Mar 2022 08:18:30 +0000 (09:18 +0100)]
drm/repaper: Reduce temporary buffer size in repaper_fb_dirty()
As the temporary buffer is no longer used to store 8-bit grayscale data,
its size can be reduced to the size needed to store the monochrome
bitmap data.
Fixes:
24c6bedefbe71de9 ("drm/repaper: Use format helper for xrgb8888 to monochrome conversion")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-6-geert@linux-m68k.org
Geert Uytterhoeven [Mon, 17 Jul 2023 13:25:40 +0000 (15:25 +0200)]
drm/armada: Fix off-by-one error in armada_overlay_get_property()
As ffs() returns one more than the index of the first bit set (zero
means no bits set), the color key mode value is shifted one position too
much.
Fix this by using FIELD_GET() instead.
Fixes:
c96103b6c49ff9a8 ("drm/armada: move colorkey properties into overlay plane state")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a4d779d954a7515ddbbf31cb0f0d8184c0e7c879.1689600265.git.geert+renesas@glider.be
Geert Uytterhoeven [Mon, 17 Jul 2023 13:23:58 +0000 (15:23 +0200)]
drm: Spelling s/randevouz/rendez-vous/
Fix a misspelling of "rendez-vous".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/084bf178dd676a4f07933eb9fcd04d3e30a779ba.1689600209.git.geert+renesas@glider.be
Geert Uytterhoeven [Mon, 17 Jul 2023 13:23:20 +0000 (15:23 +0200)]
drm: Spelling s/sempahore/semaphore/
Fix misspellings of "semaphore".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8b0542c12a2427f34a792c41ac2d2a2922874bfa.1689600102.git.geert+renesas@glider.be
Geert Uytterhoeven [Mon, 17 Jul 2023 13:16:49 +0000 (15:16 +0200)]
drm/udl: Convert to drm_crtc_helper_atomic_check()
Use the drm_crtc_helper_atomic_check() helper instead of open-coding the
same operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/dcb09c0c7bed1baee39a72caba098a399ce7f063.1689599767.git.geert+renesas@glider.be
Geert Uytterhoeven [Mon, 17 Jul 2023 13:15:44 +0000 (15:15 +0200)]
drm/bridge_connector: Handle drm_connector_init_with_ddc() failures
drm_connector_init_with_ddc() can fail, but the call in
drm_bridge_connector_init() does not check that. Fix this by adding
the missing error handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3a7e9540d8dc94298d021aa2fb046ae8616ca4dd.1689599701.git.geert+renesas@glider.be
Lyude Paul [Fri, 28 Jul 2023 22:58:57 +0000 (18:58 -0400)]
drm/nouveau/nvkm/dp: Add workaround to fix DP 1.3+ DPCD issues
Currently we use the drm_dp_dpcd_read_caps() helper in the DRM side of
nouveau in order to read the DPCD of a DP connector, which makes sure we do
the right thing and also check for extended DPCD caps. However, it turns
out we're not currently doing this on the nvkm side since we don't have
access to the drm_dp_aux structure there - which means that the DRM side of
the driver and the NVKM side can end up with different DPCD capabilities
for the same connector.
Ideally in order to fix this, we just want to use the
drm_dp_read_dpcd_caps() helper in nouveau. That's not currently possible
though, and is going to depend on having a bunch of the DP code moved out
of nvkm and into the DRM side of things as part of the GSP enablement work.
Until then however, let's workaround this problem by porting a copy of
drm_dp_read_dpcd_caps() into NVKM - which should fix this issue.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Link: https://gitlab.freedesktop.org/drm/nouveau/-/issues/211
Link: https://patchwork.freedesktop.org/patch/msgid/20230728225858.350581-1-lyude@redhat.com
Yangtao Li [Mon, 10 Jul 2023 03:23:44 +0000 (11:23 +0800)]
gpu: ipu-v3: prg: Convert to devm_platform_ioremap_resource()
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20230710032355.72914-8-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710032355.72914-8-frank.li@vivo.com
Yangtao Li [Mon, 10 Jul 2023 03:23:38 +0000 (11:23 +0800)]
gpu: ipu-v3: pre: Convert to devm_platform_ioremap_resource()
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20230710032355.72914-2-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710032355.72914-2-frank.li@vivo.com
Philipp Zabel [Tue, 20 Dec 2022 09:44:30 +0000 (10:44 +0100)]
drm/imx/ipuv3: ipuv3-plane: reuse local variable height in atomic_update
Use the already existing local variable height = drm_rect_height() >> 16
to replace other occurrences of the same value.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20221220094430.3469811-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20221220094430.3469811-1-p.zabel@pengutronix.de
Jocelyn Falempe [Thu, 13 Jul 2023 13:41:31 +0000 (15:41 +0200)]
drm/ast: report connection status on Display Port.
Aspeed always report the display port as "connected", because it
doesn't set a .detect_ctx callback.
Fix this by providing the proper detect callback for astdp and dp501.
This also fixes the following regression:
Since commit
fae7d186403e ("drm/probe-helper: Default to 640x480 if no
EDID on DP") The default resolution is now 640x480 when no monitor is
connected. But Aspeed graphics is mostly used in servers, where no monitor
is attached. This also affects the remote BMC resolution to 640x480, which
is inconvenient, and breaks the anaconda installer.
v2: Add .detect callback to the dp/dp501 connector (Jani Nikula)
v3: Use .detect_ctx callback, and refactors (Thomas Zimmermann)
Add a BMC virtual connector
v4: Better indent detect_ctx() functions (Thomas Zimmermann)
v5: Enable polling of the dp and dp501 connector status
(Thomas Zimmermann)
v6: Change check order in ast_astdp_is_connected (Jammy Huang)
Fixes:
fae7d186403e ("drm/probe-helper: Default to 640x480 if no EDID on DP")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713134316.332502-2-jfalempe@redhat.com
Jocelyn Falempe [Thu, 13 Jul 2023 13:41:30 +0000 (15:41 +0200)]
drm/ast: Add BMC virtual connector
Most aspeed devices have a BMC, which allows to remotely see the screen.
Also in the common use case, those servers don't have a display connected.
So add a Virtual connector, to reflect that even if no display is
connected, the framebuffer can still be seen remotely.
This prepares the work to implement a detect_ctx() for the Display port
connector.
v4: call drm_add_modes_noedid() with 4096x4096 (Thomas Zimmermann)
remove useless struct field init to 0 (Thomas Zimmermann)
don't use drm_simple_encoder_init() (Thomas Zimmermann)
inline ast_bmc_connector_init() (Thomas Zimmermann)
Fixes:
fae7d186403e ("drm/probe-helper: Default to 640x480 if no EDID on DP")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713134316.332502-1-jfalempe@redhat.com
Alexander Stein [Mon, 17 Jul 2023 09:29:50 +0000 (11:29 +0200)]
drm/imx/dcss: Use dev_err_probe
This helps identifying problems with downstream pipeline devices, like
HDMI/DP output.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230717092950.448823-1-alexander.stein@ew.tq-group.com
Geert Uytterhoeven [Fri, 28 Jul 2023 09:17:09 +0000 (11:17 +0200)]
drm/panel: simple: Simplify matching using of_device_get_match_data()
Both the patform_driver and mipi_dsi_driver structures contain pointers
to the match table used, so the custom code to obtain match and match
data can be replaced by calls to of_device_get_match_data().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64ded5b7e809e4c6e915b2c4d8b82e02319cd206.1690535800.git.geert+renesas@glider.be
Geert Uytterhoeven [Fri, 28 Jul 2023 09:21:11 +0000 (11:21 +0200)]
video: logo: LOGO should depend on FB_CORE i.s.o. FB
If CONFIG_FB_CORE=y and CONFIG_FB=n, the frame buffer bootup logos can
no longer be enabled. Fix this by making CONFIG_LOGO depend on
CONFIG_FB_CORE instead of CONFIG_FB, as there is no good reason for the
logo code to depend on the presence of real frame buffer device drivers.
Fixes:
55bffc8170bb ("fbdev: Split frame buffer support in FB and FB_CORE symbols")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e4142b7cc9aad9975de1bc6b1c7d86ccee487e4c.1690535997.git.geert+renesas@glider.be
Geert Uytterhoeven [Fri, 28 Jul 2023 09:19:45 +0000 (11:19 +0200)]
Revert "fbcon: Use kzalloc() in fbcon_prepare_logo()"
This reverts commit
a6a00d7e8ffd78d1cdb7a43f1278f081038c638f.
This commit is redundant, as the root cause that resulted in a false
positive was fixed by commit
27f644dc5a77f8d9 ("x86: kmsan: use C
versions of memset16/memset32/memset64").
Closes: https://lore.kernel.org/r/CAMuHMdUH4CU9EfoirSxjivg08FDimtstn7hizemzyQzYeq6b6g@mail.gmail.com/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bd8b71bb13af21cc48af40349db440f794336d3a.1690535849.git.geert+renesas@glider.be
Geert Uytterhoeven [Fri, 28 Jul 2023 09:06:21 +0000 (11:06 +0200)]
drm/gem-fb-helper: Consistenly use drm_dbg_kms()
All debug messages in drm_gem_framebuffer_helper.c use drm_dbg_kms(),
except for one, which uses drm_dbg().
Replace the outlier by drm_dbg_kms() to restore consistency.
Fixes:
c91acda3a380 ("drm/gem: Check for valid formats")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7d56615fbef2d4d0e5f4c4a23f57269bf8bdb71f.1690535176.git.geert+renesas@glider.be
Geert Uytterhoeven [Fri, 28 Jul 2023 09:03:53 +0000 (11:03 +0200)]
drm/atomic-helper: Update reference to drm_crtc_force_disable_all()
drm_crtc_force_disable_all() was renamed to
drm_helper_force_disable_all(), but one reference was not updated.
Fixes:
c2d88e06bcb9 ("drm: Move the legacy kms disable_all helper to crtc helpers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b8c9c1a8a05dbf0be8e8be98cfdeafa9cecd8cef.1690535002.git.geert+renesas@glider.be
Maíra Canal [Tue, 23 May 2023 12:32:08 +0000 (09:32 -0300)]
drm/vkms: Fix race-condition between the hrtimer and the atomic commit
Currently, it is possible for the composer to be set as enabled and then
as disabled without a proper call for the vkms_vblank_simulate(). This
is problematic, because the driver would skip one CRC output, causing CRC
tests to fail. Therefore, we need to make sure that, for each time the
composer is set as enabled, a composer job is added to the queue.
In order to provide this guarantee, add a mutex that will lock before
the composer is set as enabled and will unlock only after the composer
job is added to the queue. This way, we can have a guarantee that the
driver won't skip a CRC entry.
This race-condition is affecting the IGT test "writeback-check-output",
making the test fail and also, leaking writeback framebuffers, as the
writeback job is queued, but it is not signaled. This patch avoids both
problems.
[v2]:
* Create a new mutex and keep the spinlock across the atomic commit in
order to avoid interrupts that could result in deadlocks.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230523123207.173976-1-mcanal@igalia.com
Arthur Grillo [Sun, 9 Jul 2023 01:38:35 +0000 (22:38 -0300)]
drm/vkms: Add support to 1D gamma LUT
Support a 1D gamma LUT with interpolation for each color channel on the
VKMS driver. Add a check for the LUT length by creating
vkms_atomic_check().
Enable VKMS to run the test igt@kms_plane@pixel-format.
Tested with:
igt@kms_color@gamma
igt@kms_color@legacy-gamma
igt@kms_color@invalid-gamma-lut-sizes
v2:
- Add interpolation between the values of the LUT (Simon Ser)
v3:
- s/ratio/delta (Pekka)
- s/color_channel/channel_value (Pekka)
- s/lut_area/lut_channel
- Store the `drm_color_lut`, `lut_length`, and
`channel_value2index_ratio` inside a struct called `vkms_lut`
(Pekka)
- Pre-compute some constants values used through the LUT procedure
(Pekka)
- Change the switch statement to a cast to __u16* (Pekka)
- Make the apply_lut_to_channel_value return the computation result
(Pekka)
v4:
- Add a comment explaining that `enum lut_area` depends on the
layout of `struct drm_color_lut` (Pekka)
- Remove unused variable (kernel test robot)
v5:
- Mention that this will make it possible to run the test
igt@kms_plane@pixel-format (Maíra)
- s/had/has (Maíra)
Signed-off-by: Arthur Grillo <arthurgrillo@riseup.net>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230709013835.161004-1-arthurgrillo@riseup.net
Yangtao Li [Mon, 10 Jul 2023 03:23:52 +0000 (11:23 +0800)]
drm/tegra: sor: Convert to devm_platform_ioremap_resource()
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710032355.72914-16-frank.li@vivo.com
Yangtao Li [Mon, 10 Jul 2023 03:23:41 +0000 (11:23 +0800)]
drm/tegra: hdmi: Convert to devm_platform_ioremap_resource()
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710032355.72914-5-frank.li@vivo.com
Yangtao Li [Mon, 10 Jul 2023 03:23:49 +0000 (11:23 +0800)]
drm/tegra: dpaux: Fix incorrect return value of platform_get_irq
When platform_get_irq fails, we should return dpaux->irq
instead of -ENXIO.
Fixes:
6b6b604215c6 ("drm/tegra: Add eDP support")
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230710032355.72914-13-frank.li@vivo.com
Maxim Schwalm [Sun, 18 Jun 2023 08:50:45 +0000 (11:50 +0300)]
drm/tegra: output: hdmi: Support bridge/connector
Some Tegra device-trees may specify a video output graph, which involves
MHL bridge/simple bridge and/or connector framework. This patch adds
support for the bridge/connector attached to the HDMI output, allowing
us to model the hardware properly.
Inspired by:
29efdc2 ("drm/tegra: output: rgb: Support LVDS encoder bridge")
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # ASUS P1801-T T30
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS TF201 T30
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230618085046.10081-2-clamor95@gmail.com
Mikko Perttunen [Tue, 13 Jun 2023 09:52:14 +0000 (12:52 +0300)]
drm/tegra: Enable runtime PM during probe
Currently, engine drivers only enable runtime PM during the host1x
init callback. This can happen slightly later than the probe, which
can cause the power domain to intermittently not be turned off after
probe.
My hypothesis is that there is a race condition between the post-probe
power domain poweroff that is done from a queued work, and the
pm_runtime_enable call happening in the host1x init callback.
If the pm_runtime_enable call happens first, everything is OK and
the power off work can disable the power domain as PM runtime is
enabled and the device is runtime suspended. If power off work runs
first, PM runtime is still disabled for the device and the domain
must be kept powered.
Resolve the issue by moving the runtime PM enablement to the
probe function.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613095215.2497004-1-cyndis@kapsi.fi
Yang Li [Fri, 21 Apr 2023 08:49:52 +0000 (16:49 +0800)]
drm/tegra: dpaux: Use devm_platform_ioremap_resource()
Convert platform_get_resource(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230421084952.45275-1-yang.lee@linux.alibaba.com
Mikko Perttunen [Thu, 13 Apr 2023 08:22:02 +0000 (11:22 +0300)]
gpu: host1x: Return error when context device not attached to IOMMU
If a context device was not attached to IOMMU, we kept the old
success err value causing context devices to be unregistered but
success to be returned. This would mean that things would go on
but with context isolation disabled.
To decide on an explicit behavior, let's return an error code
here instead. If someone wants to go without IOMMU on a platform
modern enough to support context isolation, they can remove the
context devices from device tree.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413082202.114721-2-cyndis@kapsi.fi
Mikko Perttunen [Thu, 13 Apr 2023 08:22:01 +0000 (11:22 +0300)]
drm/tegra: Add error check for NVDEC firmware memory allocation
The return value for tegra_drm_alloc was missing an error check.
Add one.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413082202.114721-1-cyndis@kapsi.fi
Nathan Chancellor [Tue, 18 Jul 2023 21:44:20 +0000 (14:44 -0700)]
drm/i915: Avoid -Wconstant-logical-operand in nsecs_to_jiffies_timeout()
A proposed update to clang's -Wconstant-logical-operand to warn when the
left hand side is a constant shows the following instance in
nsecs_to_jiffies_timeout() when NSEC_PER_SEC is not a multiple of HZ,
such as CONFIG_HZ=300:
drivers/gpu/drm/i915/gem/i915_gem_wait.c:189:24: warning: use of logical '&&' with constant operand [-Wconstant-logical-operand]
189 | if (NSEC_PER_SEC % HZ &&
| ~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/i915/gem/i915_gem_wait.c:189:24: note: use '&' for a bitwise operation
189 | if (NSEC_PER_SEC % HZ &&
| ^~
| &
drivers/gpu/drm/i915/gem/i915_gem_wait.c:189:24: note: remove constant to silence this warning
1 warning generated.
Turn this into an explicit comparison against zero to make the
expression a boolean to make it clear this should be a logical check,
not a bitwise one.
Link: https://reviews.llvm.org/D142609
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-nsecs_to_jiffies_timeout-constant-logical-operand-v1-2-36ed8fc8faea@kernel.org
Nathan Chancellor [Tue, 18 Jul 2023 21:44:19 +0000 (14:44 -0700)]
drm/v3d: Avoid -Wconstant-logical-operand in nsecs_to_jiffies_timeout()
A proposed update to clang's -Wconstant-logical-operand to warn when the
left hand side is a constant shows the following instance in
nsecs_to_jiffies_timeout() when NSEC_PER_SEC is not a multiple of HZ,
such as CONFIG_HZ=300:
In file included from drivers/gpu/drm/v3d/v3d_debugfs.c:12:
drivers/gpu/drm/v3d/v3d_drv.h:343:24: warning: use of logical '&&' with constant operand [-Wconstant-logical-operand]
343 | if (NSEC_PER_SEC % HZ &&
| ~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/v3d/v3d_drv.h:343:24: note: use '&' for a bitwise operation
343 | if (NSEC_PER_SEC % HZ &&
| ^~
| &
drivers/gpu/drm/v3d/v3d_drv.h:343:24: note: remove constant to silence this warning
1 warning generated.
Turn this into an explicit comparison against zero to make the
expression a boolean to make it clear this should be a logical check,
not a bitwise one.
Link: https://reviews.llvm.org/D142609
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-nsecs_to_jiffies_timeout-constant-logical-operand-v1-1-36ed8fc8faea@kernel.org
Thierry Reding [Wed, 26 Jul 2023 18:50:09 +0000 (20:50 +0200)]
dt-bindings: display: panel: Document Hydis HV070WX2-1E0
The Hydis HV070WX2-1E0 is a 7" WXGA (800x1280) TFT LCD LVDS panel that
is one of the variants used on Google Nexus 7.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726185010.2294709-2-thierry.reding@gmail.com
Thierry Reding [Wed, 26 Jul 2023 18:50:08 +0000 (20:50 +0200)]
dt-bindings: display: panel: Move Chunghwa CLAA070WP03XG to LVDS
The Chunghwa CLAA070WP03XG is an LVDS panel, so move it to the correct
bindings file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726185010.2294709-1-thierry.reding@gmail.com
Thierry Reding [Wed, 26 Jul 2023 18:48:55 +0000 (20:48 +0200)]
dt-bindings: display: panel: Move HannStar HSD101PWW2 to LVDS
The HannStar HSD101PWW2 is an LVDS panel, so move it to the correct
bindings file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726184857.2294570-1-thierry.reding@gmail.com
Javier Martinez Canillas [Thu, 27 Jul 2023 14:04:19 +0000 (16:04 +0200)]
drm/ssd130x: Use shadow-buffer helpers when managing plane's state
The commit
45b58669e532 ("drm/ssd130x: Allocate buffer in the plane's
.atomic_check() callback") moved the buffers allocation to be done in
the primary plane's .atomic_check() callback.
But it missed that since the driver uses a shadow-buffered plane, the
__drm_gem_{reset,duplicate,destroy}_shadow_plane() helper functions
must be used in the struct drm_plane_funcs handlers.
This was missed because the mentioned commit did not remove the macro
DRM_GEM_SHADOW_PLANE_FUNCS, which leads to the custom plane's atomic
state management handlers to not be used.
Fixes:
45b58669e532 ("drm/ssd130x: Allocate buffer in the plane's .atomic_check() callback")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Closes: https://lore.kernel.org/dri-devel/
20230727122412.
2464210-1-arnd@kernel.org
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727140453.577445-1-javierm@redhat.com
Luc Ma [Tue, 18 Jul 2023 11:16:34 +0000 (19:16 +0800)]
dma-buf: Fix the typo in DMA-BUF statistics doc
The kernel-doc for DMA-BUF statistics mentions /sys/kernel/dma-buf/buffers
but the correct path is /sys/kernel/dmabuf/buffers instead.
Signed-off-by: Luc Ma <luc@sietium.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64b6749a.170a0220.3acab.2af9@mx.google.com
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Javier Martinez Canillas [Wed, 26 Jul 2023 10:54:28 +0000 (12:54 +0200)]
drm/ssd130x: Allocate buffer in the plane's .atomic_check() callback
Drivers are not allowed to fail after drm_atomic_helper_swap_state() has
been called and the new atomic state is stored into the current sw state.
Since the struct ssd130x_device .data_array is allocated in the encoder's
.atomic_enable callback, the operation can fail and this is after the new
state has been stored. So it can break an atomic mode settings assumption.
Fix this by having custom helpers to allocate, duplicate and destroy the
plane state, that will take care of allocating and freeing these buffers.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726105433.389740-2-javierm@redhat.com
Javier Martinez Canillas [Wed, 26 Jul 2023 10:54:27 +0000 (12:54 +0200)]
drm/ssd130x: Inline the ssd130x_buf_{alloc, free}() function helpers
There is only a single caller for both helper functions and these don't do
much other than allocate and free two buffers, so let's just inline them.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726105433.389740-1-javierm@redhat.com
Thomas Zimmermann [Wed, 12 Jul 2023 13:08:10 +0000 (15:08 +0200)]
drm/ast: Do not enable PCI resources multiple times
Remove ast_init_pci_config() as the ast driver already enables the PCI
resources by calling pcim_enable_device().
Suggested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230712130826.3318-1-tzimmermann@suse.de
Arnd Bergmann [Mon, 24 Jul 2023 12:17:05 +0000 (14:17 +0200)]
drm/panel: ld9040: add backlight Kconfig dependency
The driver now uses the backlight interface, which breaks when that
is disabled:
ld.lld: error: undefined symbol: devm_backlight_device_register
Enforce the necessary Kconfig dependency to avoid this.
Fixes:
c2268daa65fb ("drm/panel: ld9040: Register a backlight device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230724121736.1293270-1-arnd@kernel.org
Thomas Zimmermann [Fri, 7 Jul 2023 08:32:03 +0000 (10:32 +0200)]
fbdev: Harmonize some comments in <linux/fb.h>
Make the comments for I/O, system and DMA memory say the same.
Makes the header file's structure more obvious.
Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-13-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:32:02 +0000 (10:32 +0200)]
fbdev: Remove FB_DEFAULT_SYS_OPS
Remove the initializer macro FB_DEFAULT_SYS_OPS and its helper macro
__FB_DEFAULT_SYS_OPS_MMAP. There are no users.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Helge Deller <deller@gmx.de> (maintainer:FRAMEBUFFER LAYER)
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-12-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:32:01 +0000 (10:32 +0200)]
drm/omapdrm: Set fbdev FBINFO_VIRTFB flag
Mark the framebuffer with FBINFO_VIRTFB. The framebuffer range is
in DMA-able memory and should be accessed with the CPU's regular
memory ops.
v2:
* drop FBINFO_DEFAULT
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-11-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:32:00 +0000 (10:32 +0200)]
drm/omapdrm: Use GEM mmap for fbdev emulation
The fbdev emulation currently uses fbdev's default mmap code, which
has been written for I/O memory. Provide an mmap that uses GEM's mmap
infrastructure.
Utilize fine-grained fbdev macros to initialize struct fb_ops. The
macros set the read/write and the draw callbacks for DMA memory. Set
the fb_mmap callback to omapdrm's new mmap helper. Also select the
correct Kconfig token for fbdev's DMA helpers. Note that the DMA
helpers are the same as for system memory.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-10-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:59 +0000 (10:31 +0200)]
drm/omapdrm: Set VM flags in GEM-object mmap function
Use the mmap callback in struct drm_gem_object_funcs to set the
VM flags. Replace a number of mmap helpers in omapdrm with their
GEM helper counterparts. Generate DRM's file-operations instance
with GEM's DEFINE_DRM_GEM_FOPS.
The omapdrm driver uses DRM's drm_gem_mmap() helper to prepare
the VMA structure. It then modifies the resulting VMA state in
its own helper omap_gem_mmap_obj(). The patch improves this by
setting up the VMA in the mmap callback in drm_gem_object_funcs,
which is called from within drm_gem_mmap().
Omapdrm's omap_gem_mmap() and omap_gem_mmap() can then be removed
from the driver. A call to drm_gem_mmap() is sufficient for the
mmap operation.
Finally, with the omap functions gone, the drivers file_ops in
omapdriver_fops can be generated with DEFINE_DRM_GEM_FOPS, which
sets DRM's default helpers.
v2:
* detailed commit message (Javier)
* do not set VM_PFNMAP
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-9-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:58 +0000 (10:31 +0200)]
drm/exynos: Set fbdev FBINFO_VIRTFB flag
Mark the framebuffer with FBINFO_VIRTFB. The framebuffer range is
in DMA-able memory and should be accessed with the CPU's regular
memory ops.
v2:
* drop FBINFO_FLAG_DEFAULT
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by : Inki Dae <inki.dae@samsung.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-8-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:57 +0000 (10:31 +0200)]
drm/exynos: Use fbdev DMA helpers
Use fbdev's DMA helpers for fbdev emulation. The driver previously
used the I/O-memory helpers, while allocating DMA-able system memory.
This could (in theory) result in bus errors from accessing the memory
range.
This bug has been present since the exynos driver was first added.
v2:
* drop the pointless Fixes tag (Javier)
* fix typo in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-7-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:56 +0000 (10:31 +0200)]
drm/tegra: Store pointer to vmap'ed framebuffer in screen_buffer
Tegra uses DMA-able memory, which has to be acessed with CPU ops
for system-memory. Store the framebuffer's vmap address in struct
fb_info.screen_buffer. The currently used field 'screen_base' is
for I/O memory.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-6-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:55 +0000 (10:31 +0200)]
drm/tegra: Set fbdev FBINFO_VIRTFB flag
Mark the framebuffer with FBINFO_VIRTFB. The framebuffer range is
in DMA-able memory and should be accessed with the CPU's regular
memory ops.
v2:
* drop FBINFO_DEFAULT
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-5-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:54 +0000 (10:31 +0200)]
drm/tegra: Use fbdev DMA helpers
Use fbdev's DMA helpers for fbdev emulation. They are equivalent to the
previously used system-memory helpers, so no functional changes here.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-4-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:53 +0000 (10:31 +0200)]
drm/fbdev-dma: Use fbdev DMA helpers
Use fbdev's DMA helpers for fbdev-dma. They are equivalent to the
previously used system-memory helpers, so no functional changes here.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-3-tzimmermann@suse.de
Thomas Zimmermann [Fri, 7 Jul 2023 08:31:52 +0000 (10:31 +0200)]
fbdev: Add fb_ops init macros for framebuffers in DMA-able memory
Add initializer macros for struct fb_ops for framebuffers in DMA-able
memory areas. Also add a corresponding Kconfig token. As of now, this
is equivalent to system framebuffers and mostly useful for labeling
drivers correctly.
A later patch may add a generic DMA-specific mmap operation. Linux
offers a number of dma_mmap_*() helpers for different use cases.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707083422.18691-2-tzimmermann@suse.de
Luca Ceresoli [Wed, 19 Jul 2023 10:58:29 +0000 (12:58 +0200)]
drm/panel: db7430: remove unused variables
These variables are never referenced in the code.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719105829.148011-1-luca.ceresoli@bootlin.com
Thomas Zimmermann [Sat, 15 Jul 2023 18:52:00 +0000 (20:52 +0200)]
fbdev: Document that framebuffer_alloc() returns zero'ed data
Most fbdev drivers depend on framebuffer_alloc() to initialize the
allocated memory to 0. Document this guarantee.
v3:
* slightly reword the sentence (Miguel)
Suggested-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Cc: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-19-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:59 +0000 (20:51 +0200)]
fbdev: Remove FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
Remove the unused flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT. No
functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-18-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:58 +0000 (20:51 +0200)]
fbdev/pxafb: Remove flag FBINFO_FLAG_DEFAULT
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by devm_kzalloc(). So do not
set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-17-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:57 +0000 (20:51 +0200)]
fbdev/atafb: Remove flag FBINFO_FLAG_DEFAULT
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by a static declaration. So do
not set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-16-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:56 +0000 (20:51 +0200)]
fbdev: Remove FBINFO_FLAG_DEFAULT from framebuffer_alloc()'ed structs
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by framebuffer_alloc(). So
do not set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v4:
* clarify commit message (Geert, Dan)
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Jaya Kumar <jayalk@intworks.biz>
Cc: Helge Deller <deller@gmx.de>
Cc: Peter Jones <pjones@redhat.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Maik Broemme <mbroemme@libmpq.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: Michal Januszewski <spock@gentoo.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-15-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:55 +0000 (20:51 +0200)]
fbdev: Remove FBINFO_FLAG_DEFAULT from kzalloc()'ed structs
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by kzalloc(). So do not
set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v4:
* clarify commit message (Geert, Dan)
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-14-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:54 +0000 (20:51 +0200)]
staging: Remove flag FBINFO_FLAG_DEFAULT from fbdev drivers
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by framebuffer_alloc(). So do
not set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-13-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:53 +0000 (20:51 +0200)]
media: Remove flag FBINFO_FLAG_DEFAULT from fbdev drivers
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by kzalloc(). So do not
set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-12-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:52 +0000 (20:51 +0200)]
hid/picolcd: Remove flag FBINFO_FLAG_DEFAULT from fbdev driver
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by framebuffer_alloc(). So do
not set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-11-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:51 +0000 (20:51 +0200)]
auxdisplay: Remove flag FBINFO_FLAG_DEFAULT from fbdev drivers
The flag FBINFO_FLAG_DEFAULT is 0 and has no effect, as struct
fbinfo.flags has been allocated to zero by framebuffer_alloc(). So do
not set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Robin van der Gracht <robin@protonic.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-10-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:50 +0000 (20:51 +0200)]
sh: mach-sh7763rdp: Assign FB_MODE_IS_UNKNOWN to struct fb_videomode.flag
Assign FB_MODE_IS_UNKNOWN to sh7763fb_videomode.flag instead of
FBINFO_FLAG_DEFAULT. Both are 0, so the stored value does not change.
FBINFO_FLAG_DEFAULT is a flag for a framebuffer in struct fb_info.
Flags for videomodes are prefixed with FB_MODE_.
v3:
* include board name in commit message (Adrian)
v2:
* assign FB_MODE_IS_UNKNOWN (Adrian)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-9-tzimmermann@suse.de
Thomas Zimmermann [Sat, 15 Jul 2023 18:51:49 +0000 (20:51 +0200)]
vfio-mdev: Remove flag FBINFO_DEFAULT from fbdev sample driver
The flag FBINFO_DEFAULT is 0 and has no effect, as struct fbinfo.flags
has been allocated to zero by framebuffer_alloc(). So do not set it.
Flags should signal differences from the default values. After cleaning
up all occurrences of FBINFO_DEFAULT, the token will be removed.
v2:
* fix commit message (Miguel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kirti Wankhede <kwankhede@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230715185343.7193-8-tzimmermann@suse.de