OSDN Git Service
Nicholas Piggin [Wed, 6 Jun 2018 01:40:08 +0000 (11:40 +1000)]
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
There is a typo in
f1cb8f9beb ("powerpc/64s/radix: avoid ptesync after
set_pte and ptep_set_access_flags") config ifdef, which results in the
necessary ptesync not being issued after vmalloc.
This causes random kernel faults in module load, bpf load, anywhere
that vmalloc mappings are used.
After correcting the code, this survives a guest kernel booting
hundreds of times where previously there would be a crash every few
boots (I haven't noticed the crash on host, perhaps due to different
TLB and page table walking behaviour in hardware).
A memory clobber is also added to the flush, just to be sure it won't
be reordered with the pte set or the subsequent mapping access.
Fixes:
f1cb8f9beb ("powerpc/64s/radix: avoid ptesync after set_pte and ptep_set_access_flags")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gautham R. Shenoy [Thu, 31 May 2018 12:15:09 +0000 (17:45 +0530)]
cpuidle: powernv: Fix promotion from snooze if next state disabled
The commit
78eaa10f027c ("cpuidle: powernv/pseries: Auto-promotion of
snooze to deeper idle state") introduced a timeout for the snooze idle
state so that it could be eventually be promoted to a deeper idle
state. The snooze timeout value is static and set to the target
residency of the next idle state, which would train the cpuidle
governor to pick the next idle state eventually.
The unfortunate side-effect of this is that if the next idle state(s)
is disabled, the CPU will forever remain in snooze, despite the fact
that the system is completely idle, and other deeper idle states are
available.
This patch fixes the issue by dynamically setting the snooze timeout
to the target residency of the next enabled state on the device.
Before Patch:
POWER8 : Only nap disabled.
$ cpupower monitor sleep 30
sleep took 30.01297 seconds and exited with status 0
|Idle_Stats
PKG |CORE|CPU | snoo | Nap | Fast
0| 8| 0| 96.41| 0.00| 0.00
0| 8| 1| 96.43| 0.00| 0.00
0| 8| 2| 96.47| 0.00| 0.00
0| 8| 3| 96.35| 0.00| 0.00
0| 8| 4| 96.37| 0.00| 0.00
0| 8| 5| 96.37| 0.00| 0.00
0| 8| 6| 96.47| 0.00| 0.00
0| 8| 7| 96.47| 0.00| 0.00
POWER9: Shallow states (stop0lite, stop1lite, stop2lite, stop0, stop1,
stop2) disabled:
$ cpupower monitor sleep 30
sleep took 30.05033 seconds and exited with status 0
|Idle_Stats
PKG |CORE|CPU | snoo | stop | stop | stop | stop | stop | stop | stop | stop
0| 16| 0| 89.79| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00
0| 16| 1| 90.12| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00
0| 16| 2| 90.21| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00
0| 16| 3| 90.29| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00
After Patch:
POWER8 : Only nap disabled.
$ cpupower monitor sleep 30
sleep took 30.01200 seconds and exited with status 0
|Idle_Stats
PKG |CORE|CPU | snoo | Nap | Fast
0| 8| 0| 16.58| 0.00| 77.21
0| 8| 1| 18.42| 0.00| 75.38
0| 8| 2| 4.70| 0.00| 94.09
0| 8| 3| 17.06| 0.00| 81.73
0| 8| 4| 3.06| 0.00| 95.73
0| 8| 5| 7.00| 0.00| 96.80
0| 8| 6| 1.00| 0.00| 98.79
0| 8| 7| 5.62| 0.00| 94.17
POWER9: Shallow states (stop0lite, stop1lite, stop2lite, stop0, stop1,
stop2) disabled:
$ cpupower monitor sleep 30
sleep took 30.02110 seconds and exited with status 0
|Idle_Stats
PKG |CORE|CPU | snoo | stop | stop | stop | stop | stop | stop | stop | stop
0| 0| 0| 0.69| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 9.39| 89.70
0| 0| 1| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.05| 93.21
0| 0| 2| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 89.93
0| 0| 3| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 93.26
Fixes:
78eaa10f027c ("cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 5 Jun 2018 06:57:43 +0000 (06:57 +0000)]
powerpc: fix build failure by disabling attribute-alias warning in pci_32
Commit
2479bfc9bc600 ("powerpc: Fix build by disabling attribute-alias
warning for SYSCALL_DEFINEx") forgot arch/powerpc/kernel/pci_32.c
Latest GCC version emit the following warnings
As arch/powerpc code is built with -Werror, this breaks build with
GCC 8.1
This patch inhibits this warning
In file included from arch/powerpc/kernel/pci_32.c:14:
./include/linux/syscalls.h:233:18: error: 'sys_pciconfig_iobase' alias between functions of incompatible types 'long int(long int, long unsigned int, long unsigned int)' and 'long int(long int, long int, long int)' [-Werror=attribute-alias]
asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__)) \
^~~
./include/linux/syscalls.h:222:2: note: in expansion of macro '__SYSCALL_DEFINEx'
__SYSCALL_DEFINEx(x, sname, __VA_ARGS__)
^~~~~~~~~~~~~~~~~
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wei Yongjun [Tue, 5 Jun 2018 09:16:21 +0000 (09:16 +0000)]
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
Add the missing unlock before return from function
afu_ioctl_enable_p9_wait() in the error handling case.
Fixes:
e948e06fc63a ("ocxl: Expose the thread_id needed for wait on POWER9")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Colin Ian King [Sat, 26 May 2018 15:15:31 +0000 (16:15 +0100)]
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
Trivial fix to spelling mistake in hmi_error_types text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Colin Ian King [Fri, 30 Mar 2018 15:55:53 +0000 (16:55 +0100)]
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
Trivial fix to spelling mistake in bootx_printf message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ram Pai [Fri, 4 May 2018 20:01:51 +0000 (13:01 -0700)]
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
Disassociate the exec_key from a VMA if the VMA permission is not
PROT_EXEC anymore. Otherwise the exec_only key continues to be
associated with the vma, causing unexpected behavior.
The problem was reported on x86 by Shakeel Butt, which is also
applicable on powerpc.
Fixes:
5586cf61e108 ("powerpc: introduce execute-only pkey")
Cc: stable@vger.kernel.org # v4.16+
Reported-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Haren Myneni [Mon, 4 Jun 2018 08:33:38 +0000 (18:33 +1000)]
powerpc/powernv: copy/paste - Mask SO bit in CR
NX can set the 3rd bit in CR register for XER[SO] (Summary overflow)
which is not related to paste request. The current paste function
returns failure for a successful request when this bit is set. So mask
this bit and check the proper return status.
Fixes:
2392c8c8c045 ("powerpc/powernv/vas: Define copy/paste interfaces")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mark Greer [Fri, 6 Apr 2018 01:17:20 +0000 (18:17 -0700)]
powerpc: Remove core support for Marvell mv64x60 hostbridges
There are no longer any platforms that use Marvell's mv64x60
hostbridges so remove the supporting kernel code.
CC: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mark Greer [Fri, 6 Apr 2018 01:17:19 +0000 (18:17 -0700)]
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
There are no longer any platforms that use Marvell's mv64x60
hostbridges so remove the supporting boot code.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mark Greer [Fri, 6 Apr 2018 01:17:18 +0000 (18:17 -0700)]
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
There are no longer any platforms that use Marvell's mv64x60's i2c
controller so remove its driver.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Mark Greer <<a href="mailto:mgreer@animalcreek.com">mgreer@animalcreek.com</a>><br>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mark Greer [Fri, 6 Apr 2018 01:17:17 +0000 (18:17 -0700)]
powerpc/boot: Remove support for Marvell MPSC serial controller
There are no longer any platforms that use Marvell's MPSC serial
controller so remove its driver.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mark Greer [Fri, 6 Apr 2018 01:17:16 +0000 (18:17 -0700)]
powerpc/embedded6xx: Remove C2K board support
The C2K platform appears to be orphaned so remove code supporting it.
CC: Remi Machet <rmachet@nvidia.com>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Remi Machet <remi@machet.us>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 30 May 2018 07:06:15 +0000 (07:06 +0000)]
powerpc/lib: optimise PPC32 memcmp
At the time being, memcmp() compares two chunks of memory
byte per byte.
This patch optimises the comparison by comparing word by word.
On the same way as commit
15c2d45d17418 ("powerpc: Add 64bit
optimised memcmp"), this patch moves memcmp() into a dedicated
file named memcmp_32.S
A small benchmark performed on an 8xx comparing two chuncks
of 512 bytes performed 100000 times gives:
Before :
5852274 TB ticks
After:
1488638 TB ticks
This is almost 4 times faster
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 30 May 2018 07:06:13 +0000 (07:06 +0000)]
powerpc/lib: optimise 32 bits __clear_user()
Rewrite clear_user() on the same principle as memset(0), making use
of dcbz to clear complete cache lines.
This code is a copy/paste of memset(), with some modifications
in order to retrieve remaining number of bytes to be cleared,
as it needs to be returned in case of error.
On the same way as done on PPC64 in commit
17968fbbd19f1
("powerpc: 64bit optimised __clear_user"), the patch moves
__clear_user() into a dedicated file string_32.S
On a MPC885, throughput is almost doubled:
Before:
~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 18.990779 seconds, 52.7MB/s
After:
~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 9.611468 seconds, 104.0MB/s
On a MPC8321, throughput is multiplied by 2.12:
Before:
root@vgoippro:~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 6.844352 seconds, 146.1MB/s
After:
root@vgoippro:~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 3.218854 seconds, 310.7MB/s
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 29 May 2018 16:19:14 +0000 (16:19 +0000)]
powerpc/time: inline arch_vtime_task_switch()
arch_vtime_task_switch() is a small function which is called
only from vtime_common_task_switch(), so it is worth inlining
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Mon, 28 May 2018 06:08:34 +0000 (06:08 +0000)]
powerpc/Makefile: set -mcpu=860 flag for the 8xx
When compiled with GCC 8.1, vmlinux is significantly bigger than
with GCC 4.8.
When looking at the generated code with objdump, we notice that
all functions and loops when a 16 bytes alignment. This significantly
increases the size of the kernel. It is pointless and even
counterproductive as on the 8xx 'nop' also consumes one clock cycle.
Size of vmlinux with GCC 4.8:
text data bss dec hex filename
5801948 1626076 457796
7885820 7853fc vmlinux
Size of vmlinux with GCC 8.1:
text data bss dec hex filename
6764592 1630652 456476
8851720 871108 vmlinux
Size of vmlinux with GCC 8.1 and this patch:
text data bss dec hex filename
6331544 1631756 456476
8419776 8079c0 vmlinux
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Thu, 24 May 2018 11:33:18 +0000 (11:33 +0000)]
powerpc: Implement csum_ipv6_magic in assembly
The generic csum_ipv6_magic() generates a pretty bad result
00000000 <csum_ipv6_magic>: (PPC32)
0: 81 23 00 00 lwz r9,0(r3)
4: 81 03 00 04 lwz r8,4(r3)
8: 7c e7 4a 14 add r7,r7,r9
c: 7d 29 38 10 subfc r9,r9,r7
10: 7d 4a 51 10 subfe r10,r10,r10
14: 7d 27 42 14 add r9,r7,r8
18: 7d 2a 48 50 subf r9,r10,r9
1c: 80 e3 00 08 lwz r7,8(r3)
20: 7d 08 48 10 subfc r8,r8,r9
24: 7d 4a 51 10 subfe r10,r10,r10
28: 7d 29 3a 14 add r9,r9,r7
2c: 81 03 00 0c lwz r8,12(r3)
30: 7d 2a 48 50 subf r9,r10,r9
34: 7c e7 48 10 subfc r7,r7,r9
38: 7d 4a 51 10 subfe r10,r10,r10
3c: 7d 29 42 14 add r9,r9,r8
40: 7d 2a 48 50 subf r9,r10,r9
44: 80 e4 00 00 lwz r7,0(r4)
48: 7d 08 48 10 subfc r8,r8,r9
4c: 7d 4a 51 10 subfe r10,r10,r10
50: 7d 29 3a 14 add r9,r9,r7
54: 7d 2a 48 50 subf r9,r10,r9
58: 81 04 00 04 lwz r8,4(r4)
5c: 7c e7 48 10 subfc r7,r7,r9
60: 7d 4a 51 10 subfe r10,r10,r10
64: 7d 29 42 14 add r9,r9,r8
68: 7d 2a 48 50 subf r9,r10,r9
6c: 80 e4 00 08 lwz r7,8(r4)
70: 7d 08 48 10 subfc r8,r8,r9
74: 7d 4a 51 10 subfe r10,r10,r10
78: 7d 29 3a 14 add r9,r9,r7
7c: 7d 2a 48 50 subf r9,r10,r9
80: 81 04 00 0c lwz r8,12(r4)
84: 7c e7 48 10 subfc r7,r7,r9
88: 7d 4a 51 10 subfe r10,r10,r10
8c: 7d 29 42 14 add r9,r9,r8
90: 7d 2a 48 50 subf r9,r10,r9
94: 7d 08 48 10 subfc r8,r8,r9
98: 7d 4a 51 10 subfe r10,r10,r10
9c: 7d 29 2a 14 add r9,r9,r5
a0: 7d 2a 48 50 subf r9,r10,r9
a4: 7c a5 48 10 subfc r5,r5,r9
a8: 7c 63 19 10 subfe r3,r3,r3
ac: 7d 29 32 14 add r9,r9,r6
b0: 7d 23 48 50 subf r9,r3,r9
b4: 7c c6 48 10 subfc r6,r6,r9
b8: 7c 63 19 10 subfe r3,r3,r3
bc: 7c 63 48 50 subf r3,r3,r9
c0: 54 6a 80 3e rotlwi r10,r3,16
c4: 7c 63 52 14 add r3,r3,r10
c8: 7c 63 18 f8 not r3,r3
cc: 54 63 84 3e rlwinm r3,r3,16,16,31
d0: 4e 80 00 20 blr
0000000000000000 <.csum_ipv6_magic>: (PPC64)
0: 81 23 00 00 lwz r9,0(r3)
4: 80 03 00 04 lwz r0,4(r3)
8: 81 63 00 08 lwz r11,8(r3)
c: 7c e7 4a 14 add r7,r7,r9
10: 7f 89 38 40 cmplw cr7,r9,r7
14: 7d 47 02 14 add r10,r7,r0
18: 7d 30 10 26 mfocrf r9,1
1c: 55 29 f7 fe rlwinm r9,r9,30,31,31
20: 7d 4a 4a 14 add r10,r10,r9
24: 7f 80 50 40 cmplw cr7,r0,r10
28: 7d 2a 5a 14 add r9,r10,r11
2c: 80 03 00 0c lwz r0,12(r3)
30: 81 44 00 00 lwz r10,0(r4)
34: 7d 10 10 26 mfocrf r8,1
38: 55 08 f7 fe rlwinm r8,r8,30,31,31
3c: 7d 29 42 14 add r9,r9,r8
40: 81 04 00 04 lwz r8,4(r4)
44: 7f 8b 48 40 cmplw cr7,r11,r9
48: 7d 29 02 14 add r9,r9,r0
4c: 7d 70 10 26 mfocrf r11,1
50: 55 6b f7 fe rlwinm r11,r11,30,31,31
54: 7d 29 5a 14 add r9,r9,r11
58: 7f 80 48 40 cmplw cr7,r0,r9
5c: 7d 29 52 14 add r9,r9,r10
60: 7c 10 10 26 mfocrf r0,1
64: 54 00 f7 fe rlwinm r0,r0,30,31,31
68: 7d 69 02 14 add r11,r9,r0
6c: 7f 8a 58 40 cmplw cr7,r10,r11
70: 7c 0b 42 14 add r0,r11,r8
74: 81 44 00 08 lwz r10,8(r4)
78: 7c f0 10 26 mfocrf r7,1
7c: 54 e7 f7 fe rlwinm r7,r7,30,31,31
80: 7c 00 3a 14 add r0,r0,r7
84: 7f 88 00 40 cmplw cr7,r8,r0
88: 7d 20 52 14 add r9,r0,r10
8c: 80 04 00 0c lwz r0,12(r4)
90: 7d 70 10 26 mfocrf r11,1
94: 55 6b f7 fe rlwinm r11,r11,30,31,31
98: 7d 29 5a 14 add r9,r9,r11
9c: 7f 8a 48 40 cmplw cr7,r10,r9
a0: 7d 29 02 14 add r9,r9,r0
a4: 7d 70 10 26 mfocrf r11,1
a8: 55 6b f7 fe rlwinm r11,r11,30,31,31
ac: 7d 29 5a 14 add r9,r9,r11
b0: 7f 80 48 40 cmplw cr7,r0,r9
b4: 7d 29 2a 14 add r9,r9,r5
b8: 7c 10 10 26 mfocrf r0,1
bc: 54 00 f7 fe rlwinm r0,r0,30,31,31
c0: 7d 29 02 14 add r9,r9,r0
c4: 7f 85 48 40 cmplw cr7,r5,r9
c8: 7c 09 32 14 add r0,r9,r6
cc: 7d 50 10 26 mfocrf r10,1
d0: 55 4a f7 fe rlwinm r10,r10,30,31,31
d4: 7c 00 52 14 add r0,r0,r10
d8: 7f 80 30 40 cmplw cr7,r0,r6
dc: 7d 30 10 26 mfocrf r9,1
e0: 55 29 ef fe rlwinm r9,r9,29,31,31
e4: 7c 09 02 14 add r0,r9,r0
e8: 54 03 80 3e rotlwi r3,r0,16
ec: 7c 03 02 14 add r0,r3,r0
f0: 7c 03 00 f8 not r3,r0
f4: 78 63 84 22 rldicl r3,r3,48,48
f8: 4e 80 00 20 blr
This patch implements it in assembly for both PPC32 and PPC64
Link: https://github.com/linuxppc/linux/issues/9
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Thu, 24 May 2018 11:22:27 +0000 (11:22 +0000)]
powerpc/32: Optimise __csum_partial()
Improve __csum_partial by interleaving loads and adds.
On a 8xx, it brings neither improvement nor degradation.
On a 83xx, it brings a 25% improvement.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Fri, 18 May 2018 13:01:16 +0000 (15:01 +0200)]
powerpc/lib: Adjust .balign inside string functions for PPC32
commit
87a156fb18fe1 ("Align hot loops of some string functions")
degraded the performance of string functions by adding useless
nops
A simple benchmark on an 8xx calling 100000x a memchr() that
matches the first byte runs in 41668 TB ticks before this patch
and in 35986 TB ticks after this patch. So this gives an
improvement of approx 10%
Another benchmark doing the same with a memchr() matching the 128th
byte runs in
1011365 TB ticks before this patch and
1005682 TB ticks
after this patch, so regardless on the number of loops, removing
those useless nops improves the test by 5683 TB ticks.
Fixes:
87a156fb18fe1 ("Align hot loops of some string functions")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 24 Apr 2018 16:04:25 +0000 (18:04 +0200)]
powerpc/signal32: Use fault_in_pages_readable() to prefault user context
Use fault_in_pages_readable() to prefault user context
instead of open coding
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 17 Apr 2018 12:47:35 +0000 (14:47 +0200)]
powerpc/8xx: Remove RTC clock on 88x
The 885 familly processors don't have the Real Time Clock
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 17 Apr 2018 12:36:45 +0000 (14:36 +0200)]
powerpc/boot: remove unused variable in mpc8xx
Variable div is set but never used. Remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 17 Apr 2018 11:23:10 +0000 (13:23 +0200)]
powerpc/misc: merge reloc_offset() and add_reloc_offset()
reloc_offset() is the same as add_reloc_offset(0)
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 10 Apr 2018 06:34:35 +0000 (08:34 +0200)]
powerpc/64: optimises from64to32()
The current implementation of from64to32() gives a poor result:
0000000000000270 <.from64to32>:
270: 38 00 ff ff li r0,-1
274: 78 69 00 22 rldicl r9,r3,32,32
278: 78 00 00 20 clrldi r0,r0,32
27c: 7c 60 00 38 and r0,r3,r0
280: 7c 09 02 14 add r0,r9,r0
284: 78 09 00 22 rldicl r9,r0,32,32
288: 7c 00 4a 14 add r0,r0,r9
28c: 78 03 00 20 clrldi r3,r0,32
290: 4e 80 00 20 blr
This patch modifies from64to32() to operate in the same
spirit as csum_fold()
It swaps the two 32-bit halves of sum then it adds it with the
unswapped sum. If there is a carry from adding the two 32-bit halves,
it will carry from the lower half into the upper half, giving us the
correct sum in the upper half.
The resulting code is:
0000000000000260 <.from64to32>:
260: 78 60 00 02 rotldi r0,r3,32
264: 7c 60 1a 14 add r3,r0,r3
268: 78 63 00 22 rldicl r3,r3,32,32
26c: 4e 80 00 20 blr
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 21 Mar 2018 14:07:53 +0000 (15:07 +0100)]
powerpc/mm: Remove stale_map[] handling on non SMP processors
stale_map[] bits are only set in steal_context_smp() so
on UP processors this map is useless. Only manage it for SMP
processors.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 21 Mar 2018 14:07:51 +0000 (15:07 +0100)]
powerpc/mm: constify LAST_CONTEXT in mmu_context_nohash
last_context is 16 on the 8xx, 65535 on the 47x and 255 on other ones.
The kernel is exclusively built for the 8xx, for the 47x or for
another processor so the last context can be defined as a constant
depending on the processor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Reformat old comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 21 Mar 2018 14:07:49 +0000 (15:07 +0100)]
powerpc/mm: Avoid unnecessary test and reduce code size
no_selective_tlbil hence the use of either steal_all_contexts()
or steal_context_up() depends on the subarch, it won't change
during run. Only the 8xx uses steal_all_contexts and CONFIG_PPC_8xx
is exclusive of other processors.
This patch replaces the test of no_selective_tlbil global var by
a test of CONFIG_PPC_8xx selection. It avoids the test and
removes unnecessary code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 21 Mar 2018 14:07:47 +0000 (15:07 +0100)]
powerpc/mm: constify FIRST_CONTEXT in mmu_context_nohash
First context is now 1 for all supported platforms, so it
can be made a constant.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 28 Feb 2018 18:21:45 +0000 (19:21 +0100)]
powerpc/dma: remove unnecessary BUG()
Direction is already checked in all calling functions in
include/linux/dma-mapping.h and also in called function __dma_sync()
So really no need to check it once more here.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ravi Bangoria [Mon, 21 May 2018 04:21:08 +0000 (09:51 +0530)]
powerpc/sstep: Fix emulate_step test if VSX not present
emulate_step() tests are failing if VSX is not supported or disabled.
emulate_step_test: lxvd2x : FAIL
emulate_step_test: stxvd2x : FAIL
If !CPU_FTR_VSX, emulate_step() failure is expected and testcase should
PASS with a valid justification. After patch:
emulate_step_test: lxvd2x : PASS (!CPU_FTR_VSX)
emulate_step_test: stxvd2x : PASS (!CPU_FTR_VSX)
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ravi Bangoria [Mon, 21 May 2018 04:21:07 +0000 (09:51 +0530)]
powerpc/sstep: Fix kernel crash if VSX is not present
emulate_step() is not checking runtime VSX feature flag before
emulating an instruction. This is causing kernel crash when kernel
is compiled with CONFIG_VSX=y but running on a machine where VSX
is not supported or disabled. Ex, while running emulate_step tests
on P6 machine:
Oops: Exception in kernel mode, sig: 4 [#1]
NIP [
c000000000095c24] .load_vsrn+0x28/0x54
LR [
c000000000094bdc] .emulate_loadstore+0x167c/0x17b0
Call Trace:
0x40fe240c7ae147ae (unreliable)
.emulate_loadstore+0x167c/0x17b0
.emulate_step+0x25c/0x5bc
.test_lxvd2x_stxvd2x+0x64/0x154
.test_emulate_step+0x38/0x4c
.do_one_initcall+0x5c/0x2c0
.kernel_init_freeable+0x314/0x4cc
.kernel_init+0x24/0x160
.ret_from_kernel_thread+0x58/0xb4
With fix:
emulate_step_test: lxvd2x : FAIL
emulate_step_test: stxvd2x : FAIL
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ravi Bangoria [Mon, 21 May 2018 04:21:06 +0000 (09:51 +0530)]
powerpc/sstep: Introduce GETTYPE macro
Replace 'op->type & INSTR_TYPE_MASK' expression with GETTYPE(op->type)
macro.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Mon, 28 May 2018 23:22:38 +0000 (09:22 +1000)]
selftests/powerpc: Add perf breakpoint test
This tests perf hardware breakpoints (ie PERF_TYPE_BREAKPOINT) on
powerpc.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michal Suchanek [Mon, 28 May 2018 13:19:14 +0000 (15:19 +0200)]
powerpc/64s: Enhance the information in cpu_show_spectre_v1()
We now have barrier_nospec as mitigation so print it in
cpu_show_spectre_v1() when enabled.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Tue, 24 Apr 2018 04:15:59 +0000 (14:15 +1000)]
powerpc/64: Use barrier_nospec in syscall entry
Our syscall entry is done in assembly so patch in an explicit
barrier_nospec.
Based on a patch by Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Tue, 24 Apr 2018 04:15:58 +0000 (14:15 +1000)]
powerpc: Use barrier_nospec in copy_from_user()
Based on the x86 commit doing the same.
See commit
304ec1b05031 ("x86/uaccess: Use __uaccess_begin_nospec()
and uaccess_try_nospec") and
b3bbfb3fb5d2 ("x86: Introduce
__uaccess_begin_nospec() and uaccess_try_nospec") for more detail.
In all cases we are ordering the load from the potentially
user-controlled pointer vs a previous branch based on an access_ok()
check or similar.
Base on a patch from Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michal Suchanek [Tue, 24 Apr 2018 04:15:57 +0000 (14:15 +1000)]
powerpc/64s: Enable barrier_nospec based on firmware settings
Check what firmware told us and enable/disable the barrier_nospec as
appropriate.
We err on the side of enabling the barrier, as it's no-op on older
systems, see the comment for more detail.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michal Suchanek [Tue, 24 Apr 2018 04:15:56 +0000 (14:15 +1000)]
powerpc/64s: Patch barrier_nospec in modules
Note that unlike RFI which is patched only in kernel the nospec state
reflects settings at the time the module was loaded.
Iterating all modules and re-patching every time the settings change
is not implemented.
Based on lwsync patching.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michal Suchanek [Tue, 24 Apr 2018 04:15:55 +0000 (14:15 +1000)]
powerpc/64s: Add support for ori barrier_nospec patching
Based on the RFI patching. This is required to be able to disable the
speculation barrier.
Only one barrier type is supported and it does nothing when the
firmware does not enable it. Also re-patching modules is not supported
So the only meaningful thing that can be done is patching out the
speculation barrier at boot when the user says it is not wanted.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michal Suchanek [Tue, 24 Apr 2018 04:15:54 +0000 (14:15 +1000)]
powerpc/64s: Add barrier_nospec
A no-op form of ori (or immediate of 0 into r31 and the result stored
in r31) has been re-tasked as a speculation barrier. The instruction
only acts as a barrier on newer machines with appropriate firmware
support. On older CPUs it remains a harmless no-op.
Implement barrier_nospec using this instruction.
mpe: The semantics of the instruction are believed to be that it
prevents execution of subsequent instructions until preceding branches
have been fully resolved and are no longer executing speculatively.
There is no further documentation available at this time.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Wed, 2 May 2018 13:07:29 +0000 (23:07 +1000)]
powerpc/stacktrace: Update copyright
This now has new code in it written by Nick and I, and switch to a
SPDX tag.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Michael Ellerman [Wed, 2 May 2018 13:07:28 +0000 (23:07 +1000)]
powerpc/64s: Wire up arch_trigger_cpumask_backtrace()
This allows eg. the RCU stall detector, or the soft/hardlockup
detectors to trigger a backtrace on all CPUs.
We implement this by sending a "safe" NMI, which will actually only
send an IPI. Unfortunately the generic code prints "NMI", so that's a
little confusing but we can probably live with it.
If one of the CPUs doesn't respond to the IPI, we then print some info
from it's paca and do a backtrace based on its saved_r1.
Example output:
INFO: rcu_sched detected stalls on CPUs/tasks:
2-...0: (0 ticks this GP) idle=1be/1/
4611686018427387904 softirq=1055/1055 fqs=25735
(detected by 4, t=58847 jiffies, g=58, c=57, q=1258)
Sending NMI from CPU 4 to CPUs 2:
CPU 2 didn't respond to backtrace IPI, inspecting paca.
irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 3623 (bash)
Back trace of paca->saved_r1 (0xc0000000e1c83ba0) (possibly stale):
Call Trace:
[
c0000000e1c83ba0] [
0000000000000014] 0x14 (unreliable)
[
c0000000e1c83bc0] [
c000000000765798] lkdtm_do_action+0x48/0x80
[
c0000000e1c83bf0] [
c000000000765a40] direct_entry+0x110/0x1b0
[
c0000000e1c83c90] [
c00000000058e650] full_proxy_write+0x90/0xe0
[
c0000000e1c83ce0] [
c0000000003aae3c] __vfs_write+0x6c/0x1f0
[
c0000000e1c83d80] [
c0000000003ab214] vfs_write+0xd4/0x240
[
c0000000e1c83dd0] [
c0000000003ab5cc] ksys_write+0x6c/0x110
[
c0000000e1c83e30] [
c00000000000b860] system_call+0x58/0x6c
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Michael Ellerman [Wed, 2 May 2018 13:07:27 +0000 (23:07 +1000)]
powerpc/nmi: Add an API for sending "safe" NMIs
Currently the options we have for sending NMIs are not necessarily
safe, that is they can potentially interrupt a CPU in a
non-recoverable region of code, meaning the kernel must then panic().
But we'd like to use smp_send_nmi_ipi() to do cross-CPU calls in
situations where we don't want to risk a panic(), because it doesn't
have the requirement that interrupts must be enabled like
smp_call_function().
So add an API for the caller to indicate that it wants to use the NMI
infrastructure, but doesn't want to do anything "unsafe".
Currently that is implemented by not actually calling cause_nmi_ipi(),
instead falling back to an IPI. In future we can pass the safe
parameter down to cause_nmi_ipi() and the individual backends can
potentially take it into account before deciding what to do.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Michael Ellerman [Wed, 2 May 2018 13:07:26 +0000 (23:07 +1000)]
powerpc/64: Save stack pointer when we hard disable interrupts
A CPU that gets stuck with interrupts hard disable can be difficult to
debug, as on some platforms we have no way to interrupt the CPU to
find out what it's doing.
A stop-gap is to have the CPU save it's stack pointer (r1) in its paca
when it hard disables interrupts. That way if we can't interrupt it,
we can at least trace the stack based on where it last disabled
interrupts.
In some cases that will be total junk, but the stack trace code should
handle that. In the simple case of a CPU that disable interrupts and
then gets stuck in a loop, the stack trace should be informative.
We could clear the saved stack pointer when we enable interrupts, but
that loses information which could be useful if we have nothing else
to go on.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Michael Ellerman [Mon, 14 May 2018 13:03:16 +0000 (23:03 +1000)]
powerpc: Check address limit on user-mode return (TIF_FSCHECK)
set_fs() sets the addr_limit, which is used in access_ok() to
determine if an address is a user or kernel address.
Some code paths use set_fs() to temporarily elevate the addr_limit so
that kernel code can read/write kernel memory as if it were user
memory. That is fine as long as the code can't ever return to
userspace with the addr_limit still elevated.
If that did happen, then userspace can read/write kernel memory as if
it were user memory, eg. just with write(2). In case it's not clear,
that is very bad. It has also happened in the past due to bugs.
Commit
5ea0727b163c ("x86/syscalls: Check address limit on user-mode
return") added a mechanism to check the addr_limit value before
returning to userspace. Any call to set_fs() sets a thread flag,
TIF_FSCHECK, and if we see that on the return to userspace we go out
of line to check that the addr_limit value is not elevated.
For further info see the above commit, as well as:
https://lwn.net/Articles/722267/
https://bugs.chromium.org/p/project-zero/issues/detail?id=990
Verified to work on 64-bit Book3S using a POC that objdumps the system
call handler, and a modified lkdtm_CORRUPT_USER_DS() that doesn't kill
the caller.
Before:
$ sudo ./test-tif-fscheck
...
0000000000000000 <.data>:
0: e1 f7 8a 79 rldicl. r10,r12,30,63
4: 80 03 82 40 bne 0x384
8: 00 40 8a 71 andi. r10,r12,16384
c: 78 0b 2a 7c mr r10,r1
10: 10 fd 21 38 addi r1,r1,-752
14: 08 00 c2 41 beq- 0x1c
18: 58 09 2d e8 ld r1,2392(r13)
1c: 00 00 41 f9 std r10,0(r1)
20: 70 01 61 f9 std r11,368(r1)
24: 78 01 81 f9 std r12,376(r1)
28: 70 00 01 f8 std r0,112(r1)
2c: 78 00 41 f9 std r10,120(r1)
30: 20 00 82 41 beq 0x50
34: a6 42 4c 7d mftb r10
After:
$ sudo ./test-tif-fscheck
Killed
And in dmesg:
Invalid address limit on user-mode return
WARNING: CPU: 1 PID: 3689 at ../include/linux/syscalls.h:260 do_notify_resume+0x140/0x170
...
NIP [
c00000000001ee50] do_notify_resume+0x140/0x170
LR [
c00000000001ee4c] do_notify_resume+0x13c/0x170
Call Trace:
do_notify_resume+0x13c/0x170 (unreliable)
ret_from_except_lite+0x70/0x74
Performance overhead is essentially zero in the usual case, because
the bit is checked as part of the existing _TIF_USER_WORK_MASK check.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 14 May 2018 13:03:15 +0000 (23:03 +1000)]
powerpc: Rename thread_struct.fs to addr_limit
It's called 'fs' for historical reasons, it's named after the x86 'FS'
register. But we don't have to use that name for the member of
thread_struct, and in fact arch/x86 doesn't even call it 'fs' anymore.
So rename it to 'addr_limit', which better reflects what it's used
for, and is also the name used on other arches.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Al Viro [Tue, 29 May 2018 12:57:38 +0000 (22:57 +1000)]
powerpc/ptrace: Use copy_{from, to}_user() rather than open-coding
In PPC_PTRACE_GETHWDBGINFO and PPC_PTRACE_SETHWDEBUG we do an
access_ok() check and then __copy_{from,to}_user().
Instead we should just use copy_{from,to}_user() which does all that
for us and is less error prone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:40 +0000 (13:11 +1000)]
powerpc/eeh: Refactor report functions
The EEH report functions now share a fair bit of code around the start
and end of each function.
So factor out as much as possible, and move the traversal into a
custom function. This also allows accurate debug to be generated more
easily.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Format with clang-format]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:39 +0000 (13:11 +1000)]
powerpc/eeh: Cleaner handling of EEH_DEV_NO_HANDLER
If a device without a driver is recovered via EEH, the flag
EEH_DEV_NO_HANDLER is incorrectly left set on the device after
recovery, because the test in eeh_report_resume() for the existence of
a bound driver is done before the flag is cleared. If a driver is
later bound, and EEH experienced again, some of the drivers EEH
handers are not called.
To correct this, clear the flag unconditionally after EEH processing
is complete.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:38 +0000 (13:11 +1000)]
powerpc/eeh: Introduce eeh_set_irq_state()
To ease future refactoring, extract calls to eeh_enable_irq() and
eeh_disable_irq() from the various report functions. This makes
the report functions initial sequences more similar, as well as making
the IRQ changes visible when reading eeh_handle_normal_event().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:37 +0000 (13:11 +1000)]
powerpc/eeh: Introduce eeh_set_channel_state()
To ease future refactoring, extract setting of the channel state
from the report functions out into their own functions. This increases
the amount of code that is identical across all of the report
functions.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:36 +0000 (13:11 +1000)]
powerpc/eeh: Introduce eeh_edev_actionable()
The same test is done in every EEH report function, so factor it out.
Since eeh_dev_removed() needs to be moved higher up in the file,
simplify it a little while we're at it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:35 +0000 (13:11 +1000)]
powerpc/eeh: Introduce eeh_for_each_pe()
Add a for_each-style macro for iterating through PEs without the
boilerplate required by a traversal function. eeh_pe_next() is now
exported, as it is now used directly in place.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:34 +0000 (13:11 +1000)]
powerpc/eeh: Clean up pci_ers_result handling
As EEH event handling progresses, a cumulative result of type
pci_ers_result is built up by (some of) the eeh_report_*() functions
using either:
if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
if (*res == PCI_ERS_RESULT_NONE) *res = rc;
or:
if ((*res == PCI_ERS_RESULT_NONE) ||
(*res == PCI_ERS_RESULT_RECOVERED)) *res = rc;
if (*res == PCI_ERS_RESULT_DISCONNECT &&
rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
(Where *res is the accumulator.)
However, the intent is not immediately clear and the result in some
situations is order dependent.
Address this by assigning a priority to each result value, and always
merging to the highest priority. This renders the intent clear, and
provides a stable value for all orderings.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Minor formatting (clang-format)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:33 +0000 (13:11 +1000)]
powerpc/eeh: Add message when PE processing at parent
To aid debugging, add a message to show when EEH processing for a PE
will be done at the device's parent, rather than directly at the
device.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:32 +0000 (13:11 +1000)]
powerpc/eeh: Strengthen types of eeh traversal functions
The traversal functions eeh_pe_traverse() and eeh_pe_dev_traverse()
both provide their first argument as void * but every single user casts
it to the expected type.
Change the type of the first parameter from void * to the appropriate
type, and clean up all uses.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:31 +0000 (13:11 +1000)]
powerpc/eeh: Remove unused eeh_pcid_name()
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:30 +0000 (13:11 +1000)]
powerpc/eeh: Fix use-after-release of EEH driver
Correct two cases where eeh_pcid_get() is used to reference the driver's
module but the reference is dropped before the driver pointer is used.
In eeh_rmv_device() also refactor a little so that only two calls to
eeh_pcid_put() are needed, rather than three and the reference isn't
taken at all if it wasn't needed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam Bobroff [Fri, 25 May 2018 03:11:28 +0000 (13:11 +1000)]
powerpc/eeh: Add final message for successful recovery
Add a single log line at the end of successful EEH recovery, so that
it's clear that event processing has finished.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anju T Sudhakar [Tue, 22 May 2018 09:12:37 +0000 (14:42 +0530)]
powerpc/perf: Unregister thread-imc if core-imc not supported
Since thread-imc internally use the core-imc hardware infrastructure
and is depended on it, having thread-imc in the kernel in the
absence of core-imc is trivial. Patch disables thread-imc, if
core-imc is not registered.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anju T Sudhakar [Tue, 22 May 2018 09:12:36 +0000 (14:42 +0530)]
powerpc/perf: Return appropriate value for unknown domain
Return proper error code for unknown domain during IMC initialization.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anju T Sudhakar [Tue, 22 May 2018 09:12:35 +0000 (14:42 +0530)]
powerpc/perf: Replace the direct return with goto statement
Replace the direct return statement in imc_mem_init() with goto, to adhere
to the kernel coding style.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anju T Sudhakar [Tue, 22 May 2018 09:12:34 +0000 (14:42 +0530)]
powerpc/perf: Rearrange memory freeing in imc init
When any of the IMC (In-Memory Collection counter) devices fail
to initialize, imc_common_mem_free() frees set of memory. In doing so,
pmu_ptr pointer is also freed. But pmu_ptr pointer is used in subsequent
function (imc_common_cpuhp_mem_free()) which is wrong. Patch here reorders
the code to avoid such access.
Also free the memory which is dynamically allocated during imc
initialization, wherever required.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
YueHaibing [Wed, 25 Apr 2018 11:27:07 +0000 (19:27 +0800)]
powerpc/xics: Add missing of_node_put() in error path
The device node obtained with of_find_compatible_node() should be
released by calling of_node_put(). But it was not released when
of_get_property() failed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
[mpe: Invert the sense of the if so we only need one return path]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fabio Estevam [Sat, 5 May 2018 03:01:25 +0000 (00:01 -0300)]
powerpc: cpm_gpio: Remove owner assignment from platform_driver
Structure platform_driver does not need to set the owner field, as this
will be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Russell Currey [Fri, 11 May 2018 08:03:13 +0000 (18:03 +1000)]
powerpc/xive: Remove (almost) unused macros
The GETFIELD and SETFIELD macros in xive-regs.h aren't used except for
a single instance of GETFIELD, so replace that and remove them.
These macros are also defined in vas.h, so either those should be
eventually replaced or the macros moved into bitops.h.
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Rewrite the assignment to 'he' to avoid ffs() etc.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Stewart Smith [Thu, 29 Mar 2018 06:02:46 +0000 (17:02 +1100)]
hvc_opal: don't set tb_ticks_per_usec in udbg_init_opal_common()
time_init() will set up tb_ticks_per_usec based on reality.
time_init() is called *after* udbg_init_opal_common() during boot.
from arch/powerpc/kernel/time.c:
unsigned long tb_ticks_per_usec = 100; /* sane default */
Currently, all powernv systems have a timebase frequency of 512mhz
(
512000000/
1000000 == 0x200) - although there's nothing written
down anywhere that I can find saying that we couldn't make that
different based on the requirements in the ISA.
So, we've been (accidentally) thwacking the (currently) correct
(for powernv at least) value for tb_ticks_per_usec earlier than
we otherwise would have.
The "sane default" seems to be adequate for our purposes between
udbg_init_opal_common() and time_init() being called, and if it isn't,
then we should probably be setting it somewhere that isn't hvc_opal.c!
Signed-off-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Arnd Bergmann [Mon, 23 Apr 2018 08:36:42 +0000 (10:36 +0200)]
powerpc: remove unused to_tm() helper
to_tm() is now completely unused, the only reference being in the
_dump_time() helper that is also unused. This removes both, leaving
the rest of the powerpc RTC code y2038 safe to as far as the hardware
supports.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Arnd Bergmann [Mon, 23 Apr 2018 08:36:41 +0000 (10:36 +0200)]
powerpc: use time64_t in update_persistent_clock
update_persistent_clock() is deprecated because it suffers from overflow
in 2038 on 32-bit architectures. This changes powerpc to use the
update_persistent_clock64() replacement, and to pass down 64-bit
timestamps consistently.
This is now simpler, as we no longer have to worry about the offset
numbers in tm_year and tm_mon that are different between the Linux
conventions and RTAS.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Arnd Bergmann [Mon, 23 Apr 2018 08:36:40 +0000 (10:36 +0200)]
powerpc: use time64_t in read_persistent_clock
Looking through the remaining users of the deprecated mktime()
function, I found the powerpc rtc handlers, which use it in
place of rtc_tm_to_time64().
To clean this up, I'm changing over the read_persistent_clock()
function to the read_persistent_clock64() variant, and change
all the platform specific handlers along with it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Arnd Bergmann [Mon, 23 Apr 2018 08:36:39 +0000 (10:36 +0200)]
powerpc: rtas: clean up time handling
The to_tm() helper function operates on a signed integer for the time,
so it will suffer from overflow in 2038, even on 64-bit kernels.
Rather than fix that function, this replaces its use in the rtas
procfs implementation with the standard rtc_time64_to_tm() helper
that is very similar but is not affected by the overflow.
In order to actually support long times, the parser function gets
changed to 64-bit user input and output as well. Note that the tm_mon
and tm_year representation is slightly different, so we have to manually
add an offset here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Arnd Bergmann [Mon, 23 Apr 2018 08:36:38 +0000 (10:36 +0200)]
powerpc: always enable RTC_LIB
In order to use the rtc_tm_to_time64() and rtc_time64_to_tm()
helper functions in later patches, we have to ensure that
CONFIG_RTC_LIB is always built-in.
Note that this symbol only controls a couple of helper functions,
not the actual RTC subsystem, which remains optional and is
enabled with CONFIG_RTC_CLASS.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Olof Johansson [Wed, 6 Dec 2017 11:03:52 +0000 (12:03 +0100)]
powerpc/pasemi: Set PCI_SCAN_ALL_PCI_DEVS
Needed on Amiga X1000 with SB600.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aneesh Kumar K.V [Fri, 1 Jun 2018 08:24:02 +0000 (13:54 +0530)]
powerpc/mm/hash: hard disable irq in the SLB insert path
When inserting SLB entries for EA above 512TB, we need to hard disable irq.
This will make sure we don't take a PMU interrupt that can possibly touch
user space address via a stack dump. To prevent this, we need to hard disable
the interrupt.
Also add a comment explaining why we don't need context synchronizing isync
with slbmte.
Fixes:
f384796c4 ("powerpc/mm: Add support for handling > 512TB address in SLB miss")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aneesh Kumar K.V [Fri, 1 Jun 2018 08:24:24 +0000 (13:54 +0530)]
powerpc/mm/hugetlb: Update hugetlb related locks
With split pmd page table lock enabled, we don't use mm->page_table_lock when
updating pmd entries. This patch update hugetlb path to use the right lock
when inserting huge page directory entries into page table.
ex: if we are using hugepd and inserting hugepd entry at the pmd level, we
use pmd_lockptr, which based on config can be split pmd lock.
For update huge page directory entries itself we use mm->page_table_lock. We
do have a helper huge_pte_lockptr() for that.
Fixes:
675d99529 ("powerpc/book3s64: Enable split pmd ptlock")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aneesh Kumar K.V [Wed, 30 May 2018 13:18:04 +0000 (18:48 +0530)]
powerpc/mm/hash: Add missing isync prior to kernel stack SLB switch
Currently we do not have an isync, or any other context synchronizing
instruction prior to the slbie/slbmte in _switch() that updates the
SLB entry for the kernel stack.
However that is not correct as outlined in the ISA.
From Power ISA Version 3.0B, Book III, Chapter 11, page 1133:
"Changing the contents of ... the contents of SLB entries ... can
have the side effect of altering the context in which data
addresses and instruction addresses are interpreted, and in which
instructions are executed and data accesses are performed.
...
These side effects need not occur in program order, and therefore
may require explicit synchronization by software.
...
The synchronizing instruction before the context-altering
instruction ensures that all instructions up to and including that
synchronizing instruction are fetched and executed in the context
that existed before the alteration."
And page 1136:
"For data accesses, the context synchronizing instruction before the
slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures
that all preceding instructions that access data storage have
completed to a point at which they have reported all exceptions
they will cause."
We're not aware of any bugs caused by this, but it should be fixed
regardless.
Add the missing isync when updating kernel stack SLB entry.
Cc: stable@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Flesh out change log with more ISA text & explanation]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Wed, 30 May 2018 10:31:22 +0000 (20:31 +1000)]
powerpc/64s: Fix compiler store ordering to SLB shadow area
The stores to update the SLB shadow area must be made as they appear
in the C code, so that the hypervisor does not see an entry with
mismatched vsid and esid. Use WRITE_ONCE for this.
GCC has been observed to elide the first store to esid in the update,
which means that if the hypervisor interrupts the guest after storing
to vsid, it could see an entry with old esid and new vsid, which may
possibly result in memory corruption.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:21 +0000 (20:01 +1000)]
powerpc/64s/radix: flush remote CPUs out of single-threaded mm_cpumask
When a single-threaded process has a non-local mm_cpumask, try to use
that point to flush the TLBs out of other CPUs in the cpumask.
An IPI is used for clearing remote CPUs for a few reasons:
- An IPI can end lazy TLB use of the mm, which is required to prevent
TLB entries being created on the remote CPU. The alternative is to
drop lazy TLB switching completely, which costs 7.5% in a context
switch ping-pong test betwee a process and kernel idle thread.
- An IPI can have remote CPUs flush the entire PID, but the local CPU
can flush a specific VA. tlbie would require over-flushing of the
local CPU (where the process is running).
- A single threaded process that is migrated to a different CPU is
likely to have a relatively small mm_cpumask, so IPI is reasonable.
No other thread can concurrently switch to this mm, because it must
have been given a reference to mm_users by the current thread before it
can use_mm. mm_users can be asynchronously incremented (by
mm_activate or mmget_not_zero), but those users must use remote mm
access and can't use_mm or access user address space. Existing code
makes the this assumption already, for example sparc64 has reset
mm_cpumask using this condition since the start of history, see
arch/sparc/kernel/smp_64.c.
This reduces tlbies for a kernel compile workload from 0.90M to 0.12M,
tlbiels are increased significantly due to the PID flushing for the
cleaning up remote CPUs, and increased local flushes (PID flushes take
128 tlbiels vs 1 tlbie).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:20 +0000 (20:01 +1000)]
powerpc/64s/radix: optimise pte_update
Implementing pte_update with pte_xchg (which uses cmpxchg) is
inefficient. A single larx/stcx. works fine, no need for the less
efficient cmpxchg sequence.
Then remove the memory barriers from the operation. There is a
requirement for TLB flushing to load mm_cpumask after the store
that reduces pte permissions, which is moved into the TLB flush
code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:19 +0000 (20:01 +1000)]
powerpc/64s/radix: avoid ptesync after set_pte and ptep_set_access_flags
The ISA suggests ptesync after setting a pte, to prevent a table walk
initiated by a subsequent access from missing that store and causing a
spurious fault. This is an architectual allowance that allows an
implementation's page table walker to be incoherent with the store
queue.
However there is no correctness problem in taking a spurious fault in
userspace -- the kernel copes with these at any time, so the updated
pte will be found eventually. Spurious kernel faults on vmap memory
must be avoided, so a ptesync is put into flush_cache_vmap.
On POWER9 so far I have not found a measurable window where this can
result in more minor faults, so as an optimisation, remove the costly
ptesync from pte updates. If an implementation benefits from ptesync,
it would be better to add it back in update_mmu_cache, so it's not
done for things like fork(2).
fork --fork --exec benchmark improved 5.2% (12400->13100).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:18 +0000 (20:01 +1000)]
powerpc/64s/radix: prefetch user address in update_mmu_cache
Prefetch the faulting address in update_mmu_cache to give the page
table walker perhaps 100 cycles head start as locks are dropped and
the interrupt completed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:17 +0000 (20:01 +1000)]
powerpc/64s/radix: make ptep_get_and_clear_full non-atomic for the full case
This matches other architectures, when we know there will be no
further accesses to the address (e.g., for teardown), page table
entries can be cleared non-atomically.
The comments about NMMU are bogus: all MMU notifiers (including NMMU)
are released at this point, with their TLBs flushed. An NMMU access at
this point would be a bug.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:16 +0000 (20:01 +1000)]
powerpc/64s/radix: do not flush TLB on spurious fault
In the case of a spurious fault (which can happen due to a race with
another thread that changes the page table), the default Linux mm code
calls flush_tlb_page for that address. This is not required because
the pte will be re-fetched. Hash does not wire this up to a hardware
TLB flush for this reason. This patch avoids the flush for radix.
>From Power ISA v3.0B, p.1090:
Setting a Reference or Change Bit or Upgrading Access Authority
(PTE Subject to Atomic Hardware Updates)
If the only change being made to a valid PTE that is subject to
atomic hardware updates is to set the Refer- ence or Change bit to
1 or to add access authorities, a simpler sequence suffices
because the translation hardware will refetch the PTE if an access
is attempted for which the only problems were reference and/or
change bits needing to be set or insufficient access authority.
The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.
This reduces tlbies for a kernel compile workload from 0.95M to 0.90M.
fork --fork --exec benchmark improved 0.5% (12300->12400).
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:15 +0000 (20:01 +1000)]
powerpc/64s/radix: do not flush TLB when relaxing access
Radix flushes the TLB when updating ptes to increase permissiveness
of protection (increase access authority). Book3S does not require
TLB flushing in this case, and it is not done on hash. This patch
avoids the flush for radix.
>From Power ISA v3.0B, p.1090:
Setting a Reference or Change Bit or Upgrading Access Authority
(PTE Subject to Atomic Hardware Updates)
If the only change being made to a valid PTE that is subject to
atomic hardware updates is to set the Reference or Change bit to 1
or to add access authorities, a simpler sequence suffices because
the translation hardware will refetch the PTE if an access is
attempted for which the only problems were reference and/or change
bits needing to be set or insufficient access authority.
The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.
This reduces tlbies for a kernel compile workload from 1.28M to 0.95M,
tlbiels from 20.17M 19.68M.
fork --fork --exec benchmark improved 2.77% (12000->12300).
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aneesh Kumar K.V [Tue, 29 May 2018 14:28:41 +0000 (19:58 +0530)]
powerpc/mm/radix: Change pte relax sequence to handle nest MMU hang
When relaxing access (read -> read_write update), pte needs to be marked invalid
to handle a nest MMU bug. We also need to do a tlb flush after the pte is
marked invalid before updating the pte with new access bits.
We also move tlb flush to platform specific __ptep_set_access_flags. This will
help us to gerid of unnecessary tlb flush on BOOK3S 64 later. We don't do that
in this patch. This also helps in avoiding multiple tlbies with coprocessor
attached.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aneesh Kumar K.V [Tue, 29 May 2018 14:28:40 +0000 (19:58 +0530)]
powerpc/mm: Change function prototype
In later patch, we use the vma and psize to do tlb flush. Do the prototype
update in separate patch to make the review easy.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aneesh Kumar K.V [Tue, 29 May 2018 14:28:39 +0000 (19:58 +0530)]
powerpc/mm/radix: Move function from radix.h to pgtable-radix.c
In later patch we will update them which require them to be moved
to pgtable-radix.c. Keeping the function in radix.h results in
compile warning as below.
./arch/powerpc/include/asm/book3s/64/radix.h: In function ‘radix__ptep_set_access_flags’:
./arch/powerpc/include/asm/book3s/64/radix.h:196:28: error: dereferencing pointer to incomplete type ‘struct vm_area_struct’
struct mm_struct *mm = vma->vm_mm;
^~
./arch/powerpc/include/asm/book3s/64/radix.h:204:6: error: implicit declaration of function ‘atomic_read’; did you mean ‘__atomic_load’? [-Werror=implicit-function-declaration]
atomic_read(&mm->context.copros) > 0) {
^~~~~~~~~~~
__atomic_load
./arch/powerpc/include/asm/book3s/64/radix.h:204:21: error: dereferencing pointer to incomplete type ‘struct mm_struct’
atomic_read(&mm->context.copros) > 0) {
Instead of fixing header dependencies, we move the function to pgtable-radix.c
Also the function is now large to be a static inline . Doing the
move in separate patch helps in review.
No functional change in this patch. Only code movement.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Aneesh Kumar K.V [Tue, 29 May 2018 14:28:38 +0000 (19:58 +0530)]
powerpc/mm/hugetlb: Update huge_ptep_set_access_flags to call __ptep_set_access_flags directly
In a later patch, we want to update __ptep_set_access_flags take page size
arg. This makes ptep_set_access_flags only work with mmu_virtual_psize.
To simplify the code make huge_ptep_set_access_flags directly call
__ptep_set_access_flags so that we can compute the hugetlb page size in
hugetlb function.
Now that ptep_set_access_flags won't be called for hugetlb remove
the is_vm_hugetlb_page() check and add the assert of pte lock
unconditionally.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:13:03 +0000 (16:13 +1000)]
ocxl: Document new OCXL IOCTLs
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:13:02 +0000 (16:13 +1000)]
ocxl: Add an IOCTL so userspace knows what OCXL features are available
In order for a userspace AFU driver to call the POWER9 specific
OCXL_IOCTL_ENABLE_P9_WAIT, it needs to verify that it can actually
make that call.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:13:01 +0000 (16:13 +1000)]
ocxl: Expose the thread_id needed for wait on POWER9
In order to successfully issue as_notify, an AFU needs to know the TID
to notify, which in turn means that this information should be
available in userspace so it can be communicated to the AFU.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:13:00 +0000 (16:13 +1000)]
ocxl: Rename pnv_ocxl_spa_remove_pe to clarify it's action
The function removes the process element from NPU cache.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:12:59 +0000 (16:12 +1000)]
powerpc: use task_pid_nr() for TID allocation
The current implementation of TID allocation, using a global IDR, may
result in an errant process starving the system of available TIDs.
Instead, use task_pid_nr(), as mentioned by the original author. The
scenario described which prevented it's use is not applicable, as
set_thread_tidr can only be called after the task struct has been
populated.
In the unlikely event that 2 threads share the TID and are waiting,
all potential outcomes have been determined safe.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:12:58 +0000 (16:12 +1000)]
powerpc: Use TIDR CPU feature to control TIDR allocation
Switch the use of TIDR on it's CPU feature, rather than assuming it
is available based on architecture.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:12:57 +0000 (16:12 +1000)]
powerpc: Add TIDR CPU feature for POWER9
This patch adds a CPU feature bit to show whether the CPU has
the TIDR register available, enabling as_notify/wait in userspace.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 17:20:05 +0000 (03:20 +1000)]
powerpc/powernv: process all OPAL event interrupts with kopald
Using irq_work for processing OPAL event interrupts is not necessary.
irq_work is typically used to schedule work from NMI context, a
softirq may be more appropriate. However OPAL events are not
particularly performance or latency critical, so they can all be
invoked by kopald.
This patch removes the irq_work queueing, and instead wakes up
kopald when there is an event to be processed. kopald processes
interrupts individually, enabling irqs and calling cond_resched
between each one to minimise latencies.
Event handlers themselves should still use threaded handlers,
workqueues, etc. as necessary to avoid high interrupts-off latencies
within any single interrupt.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 12:21:48 +0000 (22:21 +1000)]
powerpc/powernv: call OPAL_QUIESCE before OPAL_SIGNAL_SYSTEM_RESET
Although it is often possible to recover a CPU that was interrupted
from OPAL with a system reset NMI, it's undesirable to interrupt them
for a few reasons. Firstly because dump/debug code itself needs to
call firmware, so it could hang on a lock or possibly corrupt a
per-cpu data structure if it or another CPU was interrupted from
OPAL. Secondly, the kexec crash dump code will not return from
interrupt to unwind the OPAL call.
Call OPAL_QUIESCE with QUIESCE_HOLD before sending an NMI IPI to
another CPU, which wait for it to leave firmware (or time out) to
avoid this problem in normal conditions. Firmware bugs may still
result in a timeout and interrupting OPAL, but that is the best
option (stops the CPU, and possibly allows firmware to be debugged).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 01:04:24 +0000 (11:04 +1000)]
powerpc/64: change softe to irqmask in show_regs and xmon
When the soft enabled flag was changed to a soft disable mask, xmon
and register dump code was not updated to reflect that, which is
confusing ('SOFTE: 1' previously meant interrupts were soft enabled,
currently it means the opposite, the general interrupt type has been
disabled).
Fix this by using the name irqmask, and printing it in hex.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 01:04:23 +0000 (11:04 +1000)]
powerpc/pmu/fsl: fix is_nmi test for irq mask change
When soft enabled was changed to irq disabled mask, this test missed
being converted (although the equivalent book3s test was converted).
The PMU drivers consider it an NMI when they take a PMI while general
interrupts are disabled. This change restores that behaviour.
Fixes:
01417c6cc7 ("powerpc/64: Change soft_enabled from flag to bitmask")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>