From 175a7427bb72050f2cc12664d62c8ed0f2b40a23 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 6 Mar 2020 10:00:45 +0100 Subject: [PATCH] dt-bindings: serial: Convert generic bindings to json-schema Convert the generic serial interface Device Tree binding documentation to json-schema. Signed-off-by: Geert Uytterhoeven Signed-off-by: Rob Herring --- .../devicetree/bindings/serial/fsl-imx-uart.txt | 2 +- .../bindings/serial/renesas,sci-serial.txt | 4 +- .../devicetree/bindings/serial/serial.txt | 56 ----------------- .../devicetree/bindings/serial/serial.yaml | 71 ++++++++++++++++++++++ 4 files changed, 74 insertions(+), 59 deletions(-) delete mode 100644 Documentation/devicetree/bindings/serial/serial.txt create mode 100644 Documentation/devicetree/bindings/serial/serial.yaml diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index 35957cbf1571..556ad11c632f 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -15,7 +15,7 @@ Optional properties: the transceiver is actually CTS_B, not RTS_B. CTS_B is always output, and RTS_B is input, regardless of dte-mode. -Please check Documentation/devicetree/bindings/serial/serial.txt +Please check Documentation/devicetree/bindings/serial/serial.yaml for the complete list of generic properties. Note: Each uart controller should have an alias correctly numbered diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index a5edf4b70c7a..5816e7d739f6 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -128,9 +128,9 @@ Optional properties: transmission, and one for reception. - dma-names: Must contain a list of two DMA names, "tx" and "rx". - {cts,dsr,dcd,rng,rts,dtr}-gpios: Specify GPIOs for modem lines, cfr. the - generic serial DT bindings in serial.txt. + generic serial DT bindings in serial.yaml. - uart-has-rtscts: Indicates dedicated lines for RTS/CTS hardware flow - control, cfr. the generic serial DT bindings in serial.txt. + control, cfr. the generic serial DT bindings in serial.yaml. Example: aliases { diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt deleted file mode 100644 index 863c2893759e..000000000000 --- a/Documentation/devicetree/bindings/serial/serial.txt +++ /dev/null @@ -1,56 +0,0 @@ -Generic Serial DT Bindings - -This document lists a set of generic properties for describing UARTs in a -device tree. Whether these properties apply to a particular device depends on -the DT bindings for the actual device. - -Optional properties: - - cts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's CTS line. - - dcd-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's DCD line. - - dsr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's DSR line. - - dtr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's DTR line. - - rng-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's RNG line. - - rts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be - used as the UART's RTS line. - - - uart-has-rtscts: The presence of this property indicates that the - UART has dedicated lines for RTS/CTS hardware flow control, and that - they are available for use (wired and enabled by pinmux configuration). - This depends on both the UART hardware and the board wiring. - Note that this property is mutually-exclusive with "cts-gpios" and - "rts-gpios" above, unless support is provided to switch between modes - dynamically. - - -Examples: - - uart1: serial@48022000 { - compatible = "ti,am3352-uart", "ti,omap3-uart"; - ti,hwmods = "uart2"; - clock-frequency = <48000000>; - reg = <0x48022000 0x2000>; - interrupts = <73>; - dmas = <&edma 28 0>, <&edma 29 0>; - dma-names = "tx", "rx"; - dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; - dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; - dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; - rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; - cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; - rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; - }; - - scifa4: serial@e6c80000 { - compatible = "renesas,scifa-sh73a0", "renesas,scifa"; - reg = <0xe6c80000 0x100>; - interrupts = ; - clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>; - clock-names = "fck"; - power-domains = <&pd_a3sp>; - uart-has-rtscts; - }; diff --git a/Documentation/devicetree/bindings/serial/serial.yaml b/Documentation/devicetree/bindings/serial/serial.yaml new file mode 100644 index 000000000000..ca2ae755b560 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/serial.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/serial/serial.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Serial Interface Generic DT Bindings + +maintainers: + - Greg Kroah-Hartman + +description: + This document lists a set of generic properties for describing UARTs in a + device tree. Whether these properties apply to a particular device depends + on the DT bindings for the actual device. + +properties: + $nodename: + pattern: "^serial(@.*)?$" + + cts-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's CTS line. + + dcd-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DCD line. + + dsr-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DSR line. + + dtr-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's DTR line. + + rng-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's RNG line. + + rts-gpios: + maxItems: 1 + description: + Must contain a GPIO specifier, referring to the GPIO pin to be used as + the UART's RTS line. + + uart-has-rtscts: + $ref: /schemas/types.yaml#/definitions/flag + description: + The presence of this property indicates that the UART has dedicated lines + for RTS/CTS hardware flow control, and that they are available for use + (wired and enabled by pinmux configuration). This depends on both the + UART hardware and the board wiring. + +if: + required: + - uart-has-rtscts +then: + properties: + cts-gpios: false + rts-gpios: false -- 2.11.0