From 5e004460f874fa590e622b200859e419f5127f5c Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Wed, 5 Sep 2018 12:42:13 -0700 Subject: [PATCH] net: dsa: b53: Add helper to set link parameters Extract the logic from b53_adjust_link() responsible for overriding a given port's link, speed, duplex and pause settings and make two helper functions to set the port's configuration and the port's link settings. We will make use of both, as separate functions while adding PHYLINK support next. Signed-off-by: Florian Fainelli Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- drivers/net/dsa/b53/b53_common.c | 89 +++++++++++++++++++++++++++------------- 1 file changed, 60 insertions(+), 29 deletions(-) diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c index 85ed264bc163..78aeaccf19a1 100644 --- a/drivers/net/dsa/b53/b53_common.c +++ b/drivers/net/dsa/b53/b53_common.c @@ -26,6 +26,7 @@ #include #include #include +#include #include #include #include @@ -947,33 +948,50 @@ static int b53_setup(struct dsa_switch *ds) return ret; } -static void b53_adjust_link(struct dsa_switch *ds, int port, - struct phy_device *phydev) +static void b53_force_link(struct b53_device *dev, int port, int link) { - struct b53_device *dev = ds->priv; - struct ethtool_eee *p = &dev->ports[port].eee; - u8 rgmii_ctrl = 0, reg = 0, off; - - if (!phy_is_pseudo_fixed_link(phydev)) - return; + u8 reg, val, off; /* Override the port settings */ if (port == dev->cpu_port) { off = B53_PORT_OVERRIDE_CTRL; - reg = PORT_OVERRIDE_EN; + val = PORT_OVERRIDE_EN; } else { off = B53_GMII_PORT_OVERRIDE_CTRL(port); - reg = GMII_PO_EN; + val = GMII_PO_EN; } - /* Set the link UP */ - if (phydev->link) + b53_read8(dev, B53_CTRL_PAGE, off, ®); + reg |= val; + if (link) reg |= PORT_OVERRIDE_LINK; + else + reg &= ~PORT_OVERRIDE_LINK; + b53_write8(dev, B53_CTRL_PAGE, off, reg); +} + +static void b53_force_port_config(struct b53_device *dev, int port, + int speed, int duplex, int pause) +{ + u8 reg, val, off; + + /* Override the port settings */ + if (port == dev->cpu_port) { + off = B53_PORT_OVERRIDE_CTRL; + val = PORT_OVERRIDE_EN; + } else { + off = B53_GMII_PORT_OVERRIDE_CTRL(port); + val = GMII_PO_EN; + } - if (phydev->duplex == DUPLEX_FULL) + b53_read8(dev, B53_CTRL_PAGE, off, ®); + reg |= val; + if (duplex == DUPLEX_FULL) reg |= PORT_OVERRIDE_FULL_DUPLEX; + else + reg &= ~PORT_OVERRIDE_FULL_DUPLEX; - switch (phydev->speed) { + switch (speed) { case 2000: reg |= PORT_OVERRIDE_SPEED_2000M; /* fallthrough */ @@ -987,21 +1005,41 @@ static void b53_adjust_link(struct dsa_switch *ds, int port, reg |= PORT_OVERRIDE_SPEED_10M; break; default: - dev_err(ds->dev, "unknown speed: %d\n", phydev->speed); + dev_err(dev->dev, "unknown speed: %d\n", speed); return; } + if (pause & MLO_PAUSE_RX) + reg |= PORT_OVERRIDE_RX_FLOW; + if (pause & MLO_PAUSE_TX) + reg |= PORT_OVERRIDE_TX_FLOW; + + b53_write8(dev, B53_CTRL_PAGE, off, reg); +} + +static void b53_adjust_link(struct dsa_switch *ds, int port, + struct phy_device *phydev) +{ + struct b53_device *dev = ds->priv; + struct ethtool_eee *p = &dev->ports[port].eee; + u8 rgmii_ctrl = 0, reg = 0, off; + int pause; + + if (!phy_is_pseudo_fixed_link(phydev)) + return; + /* Enable flow control on BCM5301x's CPU port */ if (is5301x(dev) && port == dev->cpu_port) - reg |= PORT_OVERRIDE_RX_FLOW | PORT_OVERRIDE_TX_FLOW; + pause = MLO_PAUSE_TXRX_MASK; if (phydev->pause) { if (phydev->asym_pause) - reg |= PORT_OVERRIDE_TX_FLOW; - reg |= PORT_OVERRIDE_RX_FLOW; + pause |= MLO_PAUSE_TX; + pause |= MLO_PAUSE_RX; } - b53_write8(dev, B53_CTRL_PAGE, off, reg); + b53_force_port_config(dev, port, phydev->speed, phydev->duplex, pause); + b53_force_link(dev, port, phydev->link); if (is531x5(dev) && phy_interface_is_rgmii(phydev)) { if (port == 8) @@ -1061,16 +1099,9 @@ static void b53_adjust_link(struct dsa_switch *ds, int port, } } else if (is5301x(dev)) { if (port != dev->cpu_port) { - u8 po_reg = B53_GMII_PORT_OVERRIDE_CTRL(dev->cpu_port); - u8 gmii_po; - - b53_read8(dev, B53_CTRL_PAGE, po_reg, &gmii_po); - gmii_po |= GMII_PO_LINK | - GMII_PO_RX_FLOW | - GMII_PO_TX_FLOW | - GMII_PO_EN | - GMII_PO_SPEED_2000M; - b53_write8(dev, B53_CTRL_PAGE, po_reg, gmii_po); + b53_force_port_config(dev, dev->cpu_port, 2000, + DUPLEX_FULL, MLO_PAUSE_TXRX_MASK); + b53_force_link(dev, dev->cpu_port, 1); } } -- 2.11.0