From 68579b32e786f9680e7c6b6c7d17e26943bb02b3 Mon Sep 17 00:00:00 2001 From: Hugues Fruchet Date: Tue, 13 Oct 2020 11:02:23 +0200 Subject: [PATCH] media: ov5640: fix support of BT656 bus mode Fix PCLK polarity not being taken into account. Add comments about BT656 register control. Remove useless ov5640_set_stream_bt656() function. Refine comments about MIPI IO register control. Fixes: 4039b03720f7 ("media: i2c: ov5640: Add support for BT656 mode") Signed-off-by: Hugues Fruchet Reviewed-by: Jacopo Mondi Tested-by: Lad Prabhakar Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab --- drivers/media/i2c/ov5640.c | 82 +++++++++++++++++++++++++--------------------- 1 file changed, 45 insertions(+), 37 deletions(-) diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c index 40d6983fe473..14f3afa7721a 100644 --- a/drivers/media/i2c/ov5640.c +++ b/drivers/media/i2c/ov5640.c @@ -1240,20 +1240,6 @@ static int ov5640_set_autogain(struct ov5640_dev *sensor, bool on) BIT(1), on ? 0 : BIT(1)); } -static int ov5640_set_stream_bt656(struct ov5640_dev *sensor, bool on) -{ - int ret; - - ret = ov5640_write_reg(sensor, OV5640_REG_CCIR656_CTRL00, - on ? 0x1 : 0x00); - if (ret) - return ret; - - return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ? - OV5640_REG_SYS_CTRL0_SW_PWUP : - OV5640_REG_SYS_CTRL0_SW_PWDN); -} - static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) { return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ? @@ -2018,13 +2004,13 @@ static int ov5640_set_power_mipi(struct ov5640_dev *sensor, bool on) static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on) { unsigned int flags = sensor->ep.bus.parallel.flags; - u8 pclk_pol = 0; - u8 hsync_pol = 0; - u8 vsync_pol = 0; + bool bt656 = sensor->ep.bus_type == V4L2_MBUS_BT656; + u8 polarities = 0; int ret; if (!on) { /* Reset settings to their default values. */ + ov5640_write_reg(sensor, OV5640_REG_CCIR656_CTRL00, 0x00); ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x58); ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00, 0x20); ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE01, 0x00); @@ -2048,7 +2034,35 @@ static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on) * - VSYNC: active high * - HREF: active low * - PCLK: active low + * + * VSYNC & HREF are not configured if BT656 bus mode is selected */ + + /* + * BT656 embedded synchronization configuration + * + * CCIR656 CTRL00 + * - [7]: SYNC code selection (0: auto generate sync code, + * 1: sync code from regs 0x4732-0x4735) + * - [6]: f value in CCIR656 SYNC code when fixed f value + * - [5]: Fixed f value + * - [4:3]: Blank toggle data options (00: data=1'h040/1'h200, + * 01: data from regs 0x4736-0x4738, 10: always keep 0) + * - [1]: Clip data disable + * - [0]: CCIR656 mode enable + * + * Default CCIR656 SAV/EAV mode with default codes + * SAV=0xff000080 & EAV=0xff00009d is enabled here with settings: + * - CCIR656 mode enable + * - auto generation of sync codes + * - blank toggle data 1'h040/1'h200 + * - clip reserved data (0x00 & 0xff changed to 0x01 & 0xfe) + */ + ret = ov5640_write_reg(sensor, OV5640_REG_CCIR656_CTRL00, + bt656 ? 0x01 : 0x00); + if (ret) + return ret; + /* * configure parallel port control lines polarity * @@ -2059,29 +2073,26 @@ static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on) * datasheet and hardware, 0 is active high * and 1 is active low...) */ - if (sensor->ep.bus_type == V4L2_MBUS_PARALLEL) { - if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING) - pclk_pol = 1; + if (!bt656) { if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH) - hsync_pol = 1; + polarities |= BIT(1); if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW) - vsync_pol = 1; - - ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00, - (pclk_pol << 5) | (hsync_pol << 1) | - vsync_pol); - - if (ret) - return ret; + polarities |= BIT(0); } + if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING) + polarities |= BIT(5); + + ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00, polarities); + if (ret) + return ret; /* - * powerdown MIPI TX/RX PHY & disable MIPI + * powerdown MIPI TX/RX PHY & enable DVP * * MIPI CONTROL 00 - * 4: PWDN PHY TX - * 3: PWDN PHY RX - * 2: MIPI enable + * [4] = 1 : Power down MIPI HS Tx + * [3] = 1 : Power down MIPI LS Rx + * [2] = 0 : DVP enable (MIPI disable) */ ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x18); if (ret) @@ -2098,8 +2109,7 @@ static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on) * - [3:0]: D[9:6] output enable */ ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE01, - sensor->ep.bus_type == V4L2_MBUS_PARALLEL ? - 0x7f : 0x1f); + bt656 ? 0x1f : 0x7f); if (ret) return ret; @@ -2949,8 +2959,6 @@ static int ov5640_s_stream(struct v4l2_subdev *sd, int enable) if (sensor->ep.bus_type == V4L2_MBUS_CSI2_DPHY) ret = ov5640_set_stream_mipi(sensor, enable); - else if (sensor->ep.bus_type == V4L2_MBUS_BT656) - ret = ov5640_set_stream_bt656(sensor, enable); else ret = ov5640_set_stream_dvp(sensor, enable); -- 2.11.0