From 77ddb94a4853204dc680121d59221b1be7c2297e Mon Sep 17 00:00:00 2001 From: "himanshu.madhani@cavium.com" Date: Mon, 12 Dec 2016 14:40:05 -0800 Subject: [PATCH] scsi: qla2xxx: Only allow operational MBX to proceed during RESET. This patch is allowing only ROM mailbox command which are necessary to initialize chip after a reset has been issued. In a target environment, there could be a user space daemon which can issue statistics and other management mailbox command which are non-critical. This patch will timeout non critical mailbox commands immediately rather than waiting for timeout, if driver detects that chip reset has been issued or chip reset is in progress. Reviewed-by: Hannes Reinecke Reviewed-by: Christoph Hellwig Signed-off-by: Himanshu Madhani Signed-off-by: Giridhar Malavali Signed-off-by: Martin K. Petersen --- drivers/scsi/qla2xxx/qla_mbx.c | 52 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/drivers/scsi/qla2xxx/qla_mbx.c b/drivers/scsi/qla2xxx/qla_mbx.c index 23698c998699..b31c36b251a6 100644 --- a/drivers/scsi/qla2xxx/qla_mbx.c +++ b/drivers/scsi/qla2xxx/qla_mbx.c @@ -10,6 +10,43 @@ #include #include +struct rom_cmd { + uint16_t cmd; +} rom_cmds[] = { + { MBC_LOAD_RAM }, + { MBC_EXECUTE_FIRMWARE }, + { MBC_READ_RAM_WORD }, + { MBC_MAILBOX_REGISTER_TEST }, + { MBC_VERIFY_CHECKSUM }, + { MBC_GET_FIRMWARE_VERSION }, + { MBC_LOAD_RISC_RAM }, + { MBC_DUMP_RISC_RAM }, + { MBC_LOAD_RISC_RAM_EXTENDED }, + { MBC_DUMP_RISC_RAM_EXTENDED }, + { MBC_WRITE_RAM_WORD_EXTENDED }, + { MBC_READ_RAM_EXTENDED }, + { MBC_GET_RESOURCE_COUNTS }, + { MBC_SET_FIRMWARE_OPTION }, + { MBC_MID_INITIALIZE_FIRMWARE }, + { MBC_GET_FIRMWARE_STATE }, + { MBC_GET_MEM_OFFLOAD_CNTRL_STAT }, + { MBC_GET_RETRY_COUNT }, + { MBC_TRACE_CONTROL }, +}; + +static int is_rom_cmd(uint16_t cmd) +{ + int i; + struct rom_cmd *wc; + + for (i = 0; i < ARRAY_SIZE(rom_cmds); i++) { + wc = rom_cmds + i; + if (wc->cmd == cmd) + return 1; + } + + return 0; +} /* * qla2x00_mailbox_command @@ -92,6 +129,17 @@ qla2x00_mailbox_command(scsi_qla_host_t *vha, mbx_cmd_t *mcp) return QLA_FUNCTION_TIMEOUT; } + /* check if ISP abort is active and return cmd with timeout */ + if ((test_bit(ABORT_ISP_ACTIVE, &base_vha->dpc_flags) || + test_bit(ISP_ABORT_RETRY, &base_vha->dpc_flags) || + test_bit(ISP_ABORT_NEEDED, &base_vha->dpc_flags)) && + !is_rom_cmd(mcp->mb[0])) { + ql_log(ql_log_info, vha, 0x1005, + "Cmd 0x%x aborted with timeout since ISP Abort is pending\n", + mcp->mb[0]); + return QLA_FUNCTION_TIMEOUT; + } + /* * Wait for active mailbox commands to finish by waiting at most tov * seconds. This is to serialize actual issuing of mailbox cmds during @@ -178,6 +226,7 @@ qla2x00_mailbox_command(scsi_qla_host_t *vha, mbx_cmd_t *mcp) WRT_REG_WORD(®->isp.hccr, HCCR_SET_HOST_INT); spin_unlock_irqrestore(&ha->hardware_lock, flags); + wait_time = jiffies; if (!wait_for_completion_timeout(&ha->mbx_intr_comp, mcp->tov * HZ)) { ql_dbg(ql_dbg_mbx, vha, 0x117a, @@ -186,6 +235,9 @@ qla2x00_mailbox_command(scsi_qla_host_t *vha, mbx_cmd_t *mcp) clear_bit(MBX_INTR_WAIT, &ha->mbx_cmd_flags); spin_unlock_irqrestore(&ha->hardware_lock, flags); } + if (time_after(jiffies, wait_time + 5 * HZ)) + ql_log(ql_log_warn, vha, 0x1015, "cmd=0x%x, waited %d msecs\n", + command, jiffies_to_msecs(jiffies - wait_time)); } else { ql_dbg(ql_dbg_mbx, vha, 0x1011, "Cmd=%x Polling Mode.\n", command); -- 2.11.0