From 84593a131c3af21d686d05c4b4432290a415d399 Mon Sep 17 00:00:00 2001 From: Alexandru Ardelean Date: Thu, 26 Sep 2019 13:51:32 +0300 Subject: [PATCH] spi: sprd: convert transfer word delay to spi_delay struct The Spreadtrum SPI driver is the only user of the `word_delay` field in the `spi_transfer` struct. This change converts the field to use the `spi_delay` struct. This also enforces the users to specify the delay unit to be `SPI_DELAY_UNIT_SCK`. Signed-off-by: Alexandru Ardelean Link: https://lore.kernel.org/r/20190926105147.7839-5-alexandru.ardelean@analog.com Signed-off-by: Mark Brown --- drivers/spi/spi-sprd.c | 15 ++++++++++++--- include/linux/spi/spi.h | 4 ++-- 2 files changed, 14 insertions(+), 5 deletions(-) diff --git a/drivers/spi/spi-sprd.c b/drivers/spi/spi-sprd.c index 8c9021b7f7a9..2ee1feb41681 100644 --- a/drivers/spi/spi-sprd.c +++ b/drivers/spi/spi-sprd.c @@ -669,11 +669,15 @@ static void sprd_spi_set_speed(struct sprd_spi *ss, u32 speed_hz) writel_relaxed(clk_div, ss->base + SPRD_SPI_CLKD); } -static void sprd_spi_init_hw(struct sprd_spi *ss, struct spi_transfer *t) +static int sprd_spi_init_hw(struct sprd_spi *ss, struct spi_transfer *t) { + struct spi_delay *d = &t->word_delay; u16 word_delay, interval; u32 val; + if (d->unit != SPI_DELAY_UNIT_SCK) + return -EINVAL; + val = readl_relaxed(ss->base + SPRD_SPI_CTL7); val &= ~(SPRD_SPI_SCK_REV | SPRD_SPI_NG_TX | SPRD_SPI_NG_RX); /* Set default chip selection, clock phase and clock polarity */ @@ -686,7 +690,7 @@ static void sprd_spi_init_hw(struct sprd_spi *ss, struct spi_transfer *t) * formula as below per datasheet: * interval time (source clock cycles) = interval * 4 + 10. */ - word_delay = clamp_t(u16, t->word_delay, SPRD_SPI_MIN_DELAY_CYCLE, + word_delay = clamp_t(u16, d->value, SPRD_SPI_MIN_DELAY_CYCLE, SPRD_SPI_MAX_DELAY_CYCLE); interval = DIV_ROUND_UP(word_delay - 10, 4); ss->word_delay = interval * 4 + 10; @@ -711,6 +715,8 @@ static void sprd_spi_init_hw(struct sprd_spi *ss, struct spi_transfer *t) val &= ~SPRD_SPI_DATA_LINE2_EN; writel_relaxed(val, ss->base + SPRD_SPI_CTL7); + + return 0; } static int sprd_spi_setup_transfer(struct spi_device *sdev, @@ -719,13 +725,16 @@ static int sprd_spi_setup_transfer(struct spi_device *sdev, struct sprd_spi *ss = spi_controller_get_devdata(sdev->controller); u8 bits_per_word = t->bits_per_word; u32 val, mode = 0; + int ret; ss->len = t->len; ss->tx_buf = t->tx_buf; ss->rx_buf = t->rx_buf; ss->hw_mode = sdev->mode; - sprd_spi_init_hw(ss, t); + ret = sprd_spi_init_hw(ss, t); + if (ret) + return ret; /* Set tansfer speed and valid bits */ sprd_spi_set_speed(ss, t->speed_hz); diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 7670be934643..6cb67ad53ffa 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -783,7 +783,7 @@ extern void spi_res_release(struct spi_controller *ctlr, * the next transfer or completing this @spi_message. * @word_delay_usecs: microseconds to inter word delay after each word size * (set by bits_per_word) transmission. - * @word_delay: clock cycles to inter word delay after each word size + * @word_delay: inter word delay to be introduced after each word size * (set by bits_per_word) transmission. * @effective_speed_hz: the effective SCK-speed that was used to * transfer this transfer. Set to 0 if the spi bus driver does @@ -900,8 +900,8 @@ struct spi_transfer { u8 word_delay_usecs; u16 delay_usecs; struct spi_delay cs_change_delay; + struct spi_delay word_delay; u32 speed_hz; - u16 word_delay; u32 effective_speed_hz; -- 2.11.0