From 89c6f2e5ab7a0499c6bcb25d281977ada205765d Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Thu, 3 Dec 2015 15:02:09 -0300 Subject: [PATCH] ARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi When the WiFi support was added to the IGEP0030 board, the MMC subsystem did not provide a mechanism to define power sequence providers. So a DT hack was used to toggle the WiFi chip reset and power down pins by using fake fixed regulators whose enable GPIO was the GPIOs connected to these pins. But now the simple MMC power sequence provider can be used for this and the workaround removed. Signed-off-by: Javier Martinez Canillas Acked-by: Enric Balletbo Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep0030.dts | 24 ++++++++---------------- 1 file changed, 8 insertions(+), 16 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 468608dab30a..55b0cc4f5ee5 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -15,25 +15,17 @@ model = "IGEP COM MODULE Rev. E (TI OMAP AM/DM37x)"; compatible = "isee,omap3-igep0030", "ti,omap36xx", "ti,omap3"; - /* Regulator to trigger the WIFI_PDN signal of the Wifi module */ - lbee1usjyc_pdn: lbee1usjyc_pdn { + vmmcsdio_fixed: fixedregulator-mmcsdio { compatible = "regulator-fixed"; - regulator-name = "regulator-lbee1usjyc-pdn"; + regulator-name = "vmmcsdio_fixed"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 - WIFI_PDN */ - startup-delay-us = <10000>; - enable-active-high; }; - /* Regulator to trigger the RESET_N_W signal of the Wifi module */ - lbee1usjyc_reset_n_w: lbee1usjyc_reset_n_w { - compatible = "regulator-fixed"; - regulator-name = "regulator-lbee1usjyc-reset-n-w"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* gpio_139 - RESET_N_W */ - enable-active-high; + mmc2_pwrseq: mmc2_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>, /* gpio_139 - RESET_N_W */ + <&gpio5 10 GPIO_ACTIVE_LOW>; /* gpio_138 - WIFI_PDN */ }; }; @@ -62,8 +54,8 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins &lbee1usjyc_pins>; - vmmc-supply = <&lbee1usjyc_pdn>; - vmmc_aux-supply = <&lbee1usjyc_reset_n_w>; + vmmc-supply = <&vmmcsdio_fixed>; + mmc-pwrseq = <&mmc2_pwrseq>; bus-width = <4>; non-removable; }; -- 2.11.0