From 9bb082547e46e7414aa84588b61b40e082f8bec9 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Sat, 31 Jan 2015 12:11:54 +0100 Subject: [PATCH] ARM: sun7i: hummingbird: Convert to DT label based syntax In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-hummingbird.dts | 384 ++++++++++++++-------------- 1 file changed, 191 insertions(+), 193 deletions(-) diff --git a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts b/arch/arm/boot/dts/sun7i-a20-hummingbird.dts index 2a9ee72b2b4a..8c30e126abe6 100644 --- a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts +++ b/arch/arm/boot/dts/sun7i-a20-hummingbird.dts @@ -67,199 +67,6 @@ serial4 = &uart5; }; - soc@01c00000 { - mmc0: mmc@01c0f000 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; - vmmc-supply = <®_vcc3v0>; - bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; - status = "okay"; - }; - - mmc3: mmc@01c12000 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc3_pins_a>; - vmmc-supply = <®_mmc3_vdd>; - bus-width = <4>; - non-removable; - status = "okay"; - }; - - usbphy: phy@01c13400 { - usb1_vbus-supply = <®_usb1_vbus>; - usb2_vbus-supply = <®_usb2_vbus>; - status = "okay"; - }; - - ehci0: usb@01c14000 { - status = "okay"; - }; - - ohci0: usb@01c14400 { - status = "okay"; - }; - - ahci: sata@01c18000 { - target-supply = <®_ahci_5v>; - status = "okay"; - }; - - ehci1: usb@01c1c000 { - status = "okay"; - }; - - ohci1: usb@01c1c400 { - status = "okay"; - }; - - pio: pinctrl@01c20800 { - ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 { - allwinner,pins = "PH15"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - - usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 { - allwinner,pins = "PH2"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - - mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 { - allwinner,pins = "PH9"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - - gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 { - allwinner,pins = "PH16"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - }; - - pwm: pwm@01c20e00 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_pins_a>; - status = "okay"; - }; - - ir0: ir@01c21800 { - pinctrl-names = "default"; - pinctrl-0 = <&ir0_pins_a>; - status = "okay"; - }; - - uart0: serial@01c28000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; - }; - - uart2: serial@01c28800 { - pinctrl-names = "default"; - pinctrl-0 = <&uart2_pins_a>; - status = "okay"; - }; - - uart3: serial@01c28c00 { - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins_a>; - status = "okay"; - }; - - uart4: serial@01c29000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins_a>; - status = "okay"; - }; - - uart5: serial@01c29400 { - pinctrl-names = "default"; - pinctrl-0 = <&uart5_pins_a>; - status = "okay"; - }; - - i2c0: i2c@01c2ac00 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; - - axp209: pmic@34 { - compatible = "x-powers,axp209"; - reg = <0x34>; - interrupt-parent = <&nmi_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <1>; - }; - }; - - i2c1: i2c@01c2b000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_a>; - status = "okay"; - }; - - i2c2: i2c@01c2b400 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins_a>; - status = "okay"; - }; - - i2c3: i2c@01c2b800 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_pins_a>; - status = "okay"; - }; - - spi2: spi@01c17000 { - pinctrl-names = "default"; - pinctrl-0 = <&spi2_pins_b>; - status = "okay"; - }; - - gmac: ethernet@01c50000 { - pinctrl-names = "default"; - pinctrl-0 = <&gmac_pins_rgmii_a>; - phy = <&phy1>; - phy-mode = "rgmii"; - phy-supply = <®_gmac_vdd>; - /* phy reset config */ - snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */ - snps,reset-active-low; - /* wait 1s after reset, otherwise fail to read phy id */ - snps,reset-delays-us = <0 10000 1000000>; - status = "okay"; - - phy1: ethernet-phy@1 { - reg = <1>; - }; - }; - }; - - reg_ahci_5v: ahci-5v { - pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>; - gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */ - status = "okay"; - }; - - reg_usb1_vbus: usb1-vbus { - pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>; - gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ - status = "okay"; - }; - - reg_usb2_vbus: usb2-vbus { - status = "okay"; - }; - reg_mmc3_vdd: mmc3_vdd { compatible = "regulator-fixed"; pinctrl-names = "default"; @@ -282,3 +89,194 @@ gpio = <&pio 7 16 GPIO_ACTIVE_HIGH>; /* PH16 */ }; }; + +&ahci { + target-supply = <®_ahci_5v>; + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + phy-supply = <®_gmac_vdd>; + /* phy reset config */ + snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */ + snps,reset-active-low; + /* wait 1s after reset, otherwise fail to read phy id */ + snps,reset-delays-us = <0 10000 1000000>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins_a>; + status = "okay"; +}; + +&ir0 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v0>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_mmc3_vdd>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 { + allwinner,pins = "PH15"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + + usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 { + allwinner,pins = "PH2"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + + mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 { + allwinner,pins = "PH9"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + + gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 { + allwinner,pins = "PH16"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + +®_ahci_5v { + pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>; + gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */ + status = "okay"; +}; + +®_usb1_vbus { + pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>; + gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_b>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins_a>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins_a>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_a>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&uart5_pins_a>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; -- 2.11.0