; DTC model 2 : DOCOL = PUSH IP, CALL rEXIT 13 cycles 2 words good compromize for mix FORTH/ASM code
; DTC model 3 : inlined DOCOL 9 cycles 4 words fastest
-FREQUENCY .equ 16 ; fully tested at 0.25,0.5,1,2,4,8,16 (and 24 for MSP430FR57xx) MHz
+FREQUENCY .equ 16 ; fully tested at 0.25,0.5,1,2,4,8,16 (and 24 for MSP430FR57xx) MHz
THREADS .equ 16 ; 1, 4, 8, 16, 32 search entries in dictionnary. 16 is the good compromise between speed and size.
; +40, +66, +90, +154 bytes
;HALFDUPLEX ; to use FAST FORTH with input terminal via bluetooth or WIFI (and with teraterm config = local Echo)
-TERMINALBAUDRATE .equ 115200 ; choose value considering the frequency and the UART2USB bridge, see explanations below.
+TERMINALBAUDRATE .equ 921600 ; choose value considering the frequency and the UART2USB bridge, see explanations below.
TERMINAL3WIRES ; enable 3 wires (GND,TX,RX) with XON/XOFF software flow control (PL2303TA/HXD, CP2102)
TERMINAL4WIRES ; + 18 bytes enable 4 wires with hardware flow control on RX with RTS (PL2303TA/HXD, FT232RL)
;TERMINAL5WIRES ; + 6 bytes enable 5 wires with hardware flow control on RX/TX with RTS/CTS (PL2303TA/HXD, FT232RL)
MSP430ASSEMBLER ; + 1884 bytes : adds embedded assembler with TI syntax; without, you can do all but all much more slowly...
SD_CARD_LOADER ; + 1832 bytes : to LOAD source files from SD_card
SD_CARD_READ_WRITE ; + 1196 bytes : to read, create, write and del files + source files direct copy from PC to SD_Card
-BOOTLOADER ; + 52 bytes : adds to <reset> a bootstrap to SD_CARD\BOOT.4TH.
+;BOOTLOADER ; + 52 bytes : adds to <reset> a bootstrap to SD_CARD\BOOT.4TH.
;QUIETBOOT ; + 2 bytes : to perform bootload without displaying.
FIXPOINT_INPUT ; + 78 bytes : adds the interpretation of Q15.16 numbers
VOCABULARY_SET ; + 108 bytes : adds VOCABULARY FORTH ASSEMBLER ALSO PREVIOUS ONLY DEFINITIONS (FORTH83, not ANSI)
;------------------------------------------------------------------------------- v
CONDCOMP ;; + 354 bytes : add cond. comp. : [UNDEFINED] [DEFINED] [IF] [ELSE] [THEN] CONDCOMP.f
UTILITY ;; + 426/508 bytes : add .S .RS WORDS U.R DUMP ? UTILITY.f
-FIXPOINT ; + 452 bytes : add Q15.16 words HOLDS F+ F- F/ F* F#S F. S>F 2@ 2CONSTANT FIXPOINT.f
+;FIXPOINT ; + 452 bytes : add Q15.16 words HOLDS F+ F- F/ F* F#S F. S>F 2@ 2CONSTANT FIXPOINT.f
SD_TOOLS ; + 126 bytes for trivial DIR, FAT, CLUSTER and SECTOR view, adds UTILITY SD_TOOLS.f
;ANS_CORE_COMPLIANT ; + 876 bytes : required to pass coretest.4th ; (includes items below) ANS_COMP.f
;ARITHMETIC ; + 358 bytes : add S>D M* SM/REM FM/MOD * /MOD / MOD */MOD /MOD */
; --------------------------------------------------------------------------------------------
; WARNING ! if you use PL2303TA cable as supply, open box before to weld red wire on 3v3 pad !
; --------------------------------------------------------------------------------------------
-; 9600,19200,38400,57600 (250kHz)
-; + 115200,134400 (500kHz)
-; + 201600,230400,268800 (1MHz)
-; + 403200,460800,614400 (2MHz)
-; + 806400,921600,1228800 (4MHz)
-; + 2457600 (8MHz)
-; + 3000000 (16MHz)
-; + 6000000 (24MHz, MSP430FR57xx)
+; 9600,19200,38400,57600 (250kHz)
+; + 115200,134400 (500kHz)
+; + 201600,230400,268800 (1MHz)
+; + 403200,460800,614400 (2MHz)
+; + 806400,921600,1228800 (4MHz)
+; + 2457600,3000000 (8MHz)
+; + 6000000 (16,24MHz) (shorten the 1m cable or use a Si8622EC-B-IS to regenerate TTL levels)
; UARTtoUSB module with Silabs CP2102 (supply current = 20 mA)
; --------------------------------------------------------------------------------------------
; WARNING ! if you use PL2303TA cable as supply, open box before to weld red wire on 3v3 pad !
; --------------------------------------------------------------------------------------------
-; 9600,19200,38400,57600,115200,134400 (500kHz)
-; + 201600,230400,268800 (1MHz)
-; + 403200,460800,614400 (2MHz)
-; + 806400,921600,1228800 (4MHz)
-; + 2457600 (8MHz)
-; + 3000000 (16MHz, 24MHz with MSP430FR57xx))
+; 9600,19200,38400,57600 (250kHz)
+; + 115200,134400 (500kHz)
+; + 201600,230400,268800 (1MHz)
+; + 403200,460800,614400 (2MHz)
+; + 806400,921600,1228800 (4MHz)
+; + 2457600,3000000 (8MHz)
+; + 6000000 (16,24MHz) (shorten the 1m cable or use a Si8622EC-B-IS to regenerate TTL levels)
; UARTtoUSB module with FTDI FT232RL (FT230X don't work correctly)
; --------------------------------------;
ADD #4,RSP ;1 remove SR and PC from stack, SR flags are lost (unused by FORTH interpreter)
.word 173Ah ;6 POPM ;W=buffer_bound, T=0Dh,S=20h, IP=AYEMIT_RET
-; .word 1758h ;8 POPM Y=oldSR, X=oldPC, W=buffer_bound, T=0Dh,S=20h, IP=AYEMIT_RET
-; BIC #78h,Y ;2 SCG1,SCG0,OSCOFF,CPUOFF and GIE are OFF in oldSR
-; MOV Y,SR ;1 restore SR with UF9 to UF11 flags, to preserve them.
; vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv;
; starts the 2th stopwatch ;
; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^;
; vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv;
; stops the 3th stopwatch ; 3th bottleneck result : 17~ + LPMx wake_up time ( + 5~ XON loop if F/Bds<230400 )
; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^;
-AKEYREAD1 ; <--- XON RET address 2 ; first emergency: anticipate XOFF on CR as soon as possible
+AKEYREAD1 CMP.B S,Y ;1 printable char ?
+ JHS ASTORETEST ;2 yes
CMP.B T,Y ;1 char = CR ?
JZ RXOFF ;2 then RET to ENDACCEPT
; vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv;+ 4 to send RXOFF
-; stops the first stopwatch ;= first bottleneck, best case result: 24~ + LPMx wake_up time..
-; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^; ...or 11~ in case of empty line
- CMP.B S,Y ;1 printable char ?
- JHS ASTORETEST ;2 yes
+; stops the first stopwatch ;= first bottleneck, best case result: 27~ + LPMx wake_up time..
+; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^; ...or 14~ in case of empty line
AQBS CMP.B #8,Y ;1 char = BS ?
JNE WAITaKEY ;2 case of other control chars
; --------------------------------------;
JZ YEMIT1 ; 2 yes: send echo then loopback
MOV.B Y,0(TOS) ; 3 no: store char @ Ptr, send echo then loopback
ADD #1,TOS ; 1 increment Ptr
-YEMIT1 BIT #UCTXIFG,&TERMIFG ; 3 wait the sending end of previous char, useless at high baudrates
+YEMIT1
+ .IF TERMINALBAUDRATE/FREQUENCY <230400
+ BIT #UCTXIFG,&TERMIFG ; 3 wait the sending end of previous char (sent before ACCEPT), useless at high baudrates
JZ YEMIT1 ; 2
+ .ENDIF
.IFDEF TERMINAL5WIRES ;
-YEMIT2 BIT.B #CTS,&HANDSHAKIN ;
- JNZ YEMIT2 ;
+YEMIT2 BIT.B #CTS,&HANDSHAKIN ; 3
+ JNZ YEMIT2 ; 2
.ENDIF
YEMIT .word 4882h ; hi7/4~ lo:12/4~ send/send_not echo to terminal
.word TERMTXBUF ; 3 MOV Y,&TERMTXBUF
AYEMIT_RET FORTHtoASM ; 0 YEMII NEXT address; NOP9
SUB #2,IP ; 1 set YEMIT NEXT address to AYEMIT_RET
WAITaKEY BIT #UCRXIFG,&TERMIFG ; 3 new char in TERMRXBUF ?
- JZ WAITaKEY ; 2 no
JNZ AKEYREAD ; 2 yes
+ JZ WAITaKEY ; 2 no
; vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv;
-; stops the 2th stopwatch ; best case result: 31~/28~ (with/without echo) ==> 322/357 kBds/MHz
+; stops the 2th stopwatch ; best case result: 26~/22~ (with/without echo) ==> 385/455 kBds/MHz
; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^;
; --------------------------------------;
; .word DOT ; display SYSSNIV
; .word DOT ; display SYSUNIV
.word XSQUOTE
- .byte 39," FastForth V202",FREQ," (C) J.M.Thoorens "
+ .byte 39," FastForth V203",FREQ," (C) J.M.Thoorens "
.word TYPE
.word LIT,FRAM_FULL,HERE,MINUS,UDOT
.word XSQUOTE ;
OSDN Git Service
