From: Roger Quadros <rogerq@ti.com>
Date: Mon, 27 Jul 2015 13:10:17 +0000 (+0300)
Subject: ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
X-Git-Url: http://git.osdn.net/view?p=sagit-ice-cold%2Fkernel_xiaomi_msm8998.git;a=commitdiff_plain;h=84ad1bab0eebd2e2b2dd3c3db7b88cade22a6de1

ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2

The VBUS line of USB2 is connected to VBUS detect logic on
the PMIC. Use the palmas-usb driver to report VBUS events
to the USB driver.

As the palmas-usb driver supports GPIO based ID reporting
provide the GPIO for ID pin as well.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---

diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 53884bc65abd..568adf5efde0 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -98,13 +98,6 @@
 		pinctrl-0 = <&extcon_usb1_pins>;
 	};
 
-	extcon_usb2: extcon_usb2 {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&extcon_usb2_pins>;
-	};
-
 	hdmi0: connector {
 		compatible = "hdmi-connector";
 		label = "hdmi";
@@ -326,12 +319,6 @@
 		>;
 	};
 
-	extcon_usb2_pins: extcon_usb2_pins {
-		pinctrl-single,pins = <
-			0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */
-		>;
-	};
-
 	tpd12s015_pins: pinmux_tpd12s015_pins {
 		pinctrl-single,pins = <
 			0x3b0 (PIN_OUTPUT | MUX_MODE14)		/* gpio7_10 CT_CP_HPD */
@@ -504,6 +491,14 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
+
+		extcon_usb2: tps659038_usb {
+			compatible = "ti,palmas-usb-vid";
+			ti,enable-vbus-detection;
+			ti,enable-id-detection;
+			id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>;
+		};
+
 	};
 
 	tmp102: tmp102@48 {
@@ -632,6 +627,14 @@
 };
 
 &usb2 {
+	/*
+	 * Stand alone usage is peripheral only.
+	 * However, with some resistor modifications
+	 * this port can be used via expansion connectors
+	 * as "host" or "dual-role". If so, provide
+	 * the necessary dr_mode override in the expansion
+	 * board's DT.
+	 */
 	dr_mode = "peripheral";
 };