OSDN Git Service
Bjørn Mork [Thu, 24 May 2012 09:19:04 +0000 (11:19 +0200)]
USB: qcserial: Add Sierra Wireless device IDs
commit
c41444ccfa33a1c20efa319e554cb531576e64a2 upstream.
Some additional IDs found in the BSD/GPL licensed out-of-tree
GobiSerial driver from Sierra Wireless.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Zelenoff [Tue, 5 Jun 2012 13:58:04 +0000 (17:58 +0400)]
USB: mos7840: Fix compilation of usb serial driver
commit
b9c87663eead64c767e72a373ae6f8a94bead459 upstream.
The __devinitconst section can't be referenced
from usb_serial_device structure. Thus removed it as
it done in other mos* device drivers.
Error itself:
WARNING: drivers/usb/serial/mos7840.o(.data+0x8): Section mismatch in reference
from the variable moschip7840_4port_device to the variable
.devinit.rodata:id_table
The variable moschip7840_4port_device references
the variable __devinitconst id_table
[v2] no attach now
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andiry Xu [Wed, 13 Jun 2012 02:51:57 +0000 (10:51 +0800)]
xHCI: Increase the timeout for controller save/restore state operation
commit
622eb783fe6ff4c1baa47db16c3a5db97f9e6e50 upstream.
When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.
xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.
Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/
1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.
This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit
5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation"
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Janne Kalliomäki [Sun, 17 Jun 2012 21:05:24 +0000 (17:05 -0400)]
hfsplus: fix overflow in sector calculations in hfsplus_submit_bio
commit
a6dc8c04218eb752ff79cdc24a995cf51866caed upstream.
The variable io_size was unsigned int, which caused the wrong sector number
to be calculated after aligning it. This then caused mount to fail with big
volumes, as backup volume header information was searched from a
wrong sector.
Signed-off-by: Janne Kalliomäki <janne@tuxera.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 29 May 2012 15:57:52 +0000 (17:57 +0200)]
USB: option: fix port-data abuse
commit
4273f9878b0a8271df055e3c8f2e7f08c6a4a2f4 upstream.
Commit
8b4c6a3ab596961b78465 ("USB: option: Use generic USB wwan code")
moved option port-data allocation to usb_wwan_startup but still cast the
port data to the old struct...
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 29 May 2012 16:22:48 +0000 (18:22 +0200)]
USB: option: fix memory leak
commit
b9c3aab315b51f81649a0d737c4c73783fbd8de0 upstream.
Fix memory leak introduced by commit
383cedc3bb435de7a2 ("USB: serial:
full autosuspend support for the option driver") which allocates
usb-serial data but never frees it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
说不得 [Mon, 28 May 2012 13:31:29 +0000 (21:31 +0800)]
USB: option: add more YUGA device ids
commit
0ef0be15fd2564767f114c249fc4af704d8e16f4 upstream.
Signed-off-by: gavin zhu <gavin.zhu@qq.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Bird [Mon, 28 May 2012 11:43:06 +0000 (12:43 +0100)]
USB: option: Updated Huawei K4605 has better id
commit
42ca7da1c2363dbef4ba1b6917c4c02274b6a5e2 upstream.
Later firmwares for this device now have proper subclass and
protocol info so we can identify it nicely without needing to use
the blacklist. I'm not removing the old 0xff matching as there
may be devices in the field that still need that.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Sat, 19 May 2012 17:20:50 +0000 (19:20 +0200)]
USB: option: Add Vodafone/Huawei K5005 support
commit
4cbbb039a9719fb3bba73d255c6a95bc6dc6428b upstream.
Tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Thu, 31 May 2012 19:26:38 +0000 (15:26 -0400)]
NFSv4.1: Fix a request leak on the back channel
commit
b3b02ae5865c2dcd506322e0fc6def59a042e72f upstream.
If the call to svc_process_common() fails, then the request
needs to be freed before we can exit bc_svc_process.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andre Przywara [Tue, 29 May 2012 11:07:31 +0000 (13:07 +0200)]
xen/setup: filter APERFMPERF cpuid feature out
commit
5e626254206a709c6e937f3dda69bf26c7344f6f upstream.
Xen PV kernels allow access to the APERF/MPERF registers to read the
effective frequency. Access to the MSRs is however redirected to the
currently scheduled physical CPU, making consecutive read and
compares unreliable. In addition each rdmsr traps into the hypervisor.
So to avoid bogus readouts and expensive traps, disable the kernel
internal feature flag for APERF/MPERF if running under Xen.
This will
a) remove the aperfmperf flag from /proc/cpuinfo
b) not mislead the power scheduler (arch/x86/kernel/cpu/sched.c) to
use the feature to improve scheduling (by default disabled)
c) not mislead the cpufreq driver to use the MSRs
This does not cover userland programs which access the MSRs via the
device file interface, but this will be addressed separately.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jaccon Bastiaansen [Mon, 30 Apr 2012 09:53:43 +0000 (11:53 +0200)]
ARM i.MX imx21ads: Fix overlapping static i/o mappings
commit
350ab15bb2ffe7103bc6bf6c634f3c5b286eaf2a upstream.
The statically defined I/O memory regions for the i.MX21 on chip
peripherals and the on board I/O peripherals of the i.MX21ADS board
overlap. This results in a kernel crash during startup. This is fixed
by reducing the memory range for the on board I/O peripherals to the
actually required range.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sun, 17 Jun 2012 18:23:33 +0000 (11:23 -0700)]
Linux 3.0.35
Dave Hansen [Tue, 29 May 2012 22:06:46 +0000 (15:06 -0700)]
hugetlb: fix resv_map leak in error path
commit
c50ac050811d6485616a193eb0f37bfbd191cc89 and
4523e1458566a0e8ecfaff90f380dd23acc44d27 upstream.
When called for anonymous (non-shared) mappings, hugetlb_reserve_pages()
does a resv_map_alloc(). It depends on code in hugetlbfs's
vm_ops->close() to release that allocation.
However, in the mmap() failure path, we do a plain unmap_region() without
the remove_vma() which actually calls vm_ops->close().
This is a decent fix. This leak could get reintroduced if new code (say,
after hugetlb_reserve_pages() in hugetlbfs_file_mmap()) decides to return
an error. But, I think it would have to unroll the reservation anyway.
Christoph's test case:
http://marc.info/?l=linux-mm&m=
133728900729735
This patch applies to 3.4 and later. A version for earlier kernels is at
https://lkml.org/lkml/2012/5/22/418.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: Christoph Lameter <cl@linux.com>
Tested-by: Christoph Lameter <cl@linux.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KyongHo [Tue, 29 May 2012 22:06:49 +0000 (15:06 -0700)]
mm: fix faulty initialization in vmalloc_init()
commit
dbda591d920b4c7692725b13e3f68ecb251e9080 upstream.
The transfer of ->flags causes some of the static mapping virtual
addresses to be prematurely freed (before the mapping is removed) because
VM_LAZY_FREE gets "set" if tmp->flags has VM_IOREMAP set. This might
cause subsequent vmalloc/ioremap calls to fail because it might allocate
one of the freed virtual address ranges that aren't unmapped.
va->flags has different types of flags from tmp->flags. If a region with
VM_IOREMAP set is registered with vm_area_add_early(), it will be removed
by __purge_vmap_area_lazy().
Fix vmalloc_init() to correctly initialize vmap_area for the given
vm_struct.
Also initialise va->vm. If it is not set, find_vm_area() for the early
vm regions will always fail.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com>
Cc: "Olav Haugan" <ohaugan@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minchan Kim [Tue, 10 Jan 2012 23:08:39 +0000 (15:08 -0800)]
mm/vmalloc.c: change void* into explict vm_struct*
commit
db1aecafef58b5dda39c4228debe2c845e4a27ab upstream.
vmap_area->private is void* but we don't use the field for various purpose
but use only for vm_struct. So change it to a vm_struct* with naming to
improve for readability and type checking.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dean Nelson [Thu, 25 Aug 2011 14:39:24 +0000 (14:39 +0000)]
e1000: save skb counts in TX to avoid cache misses
commit
31c15a2f24ebdab14333d9bf5df49757842ae2ec upstream.
Virtual Machines with emulated e1000 network adapter running on Parallels'
server were seeing kernel panics due to the e1000 driver dereferencing an
unexpected NULL pointer retrieved from buffer_info->skb.
The problem has been addressed for the e1000e driver, but not for the e1000.
Since the two drivers share similar code in the affected area, a port of the
following e1000e driver commit solves the issue for the e1000 driver:
commit
9ed318d546a29d7a591dbe648fd1a2efe3be1180
Author: Tom Herbert <therbert@google.com>
Date: Wed May 5 14:02:27 2010 +0000
e1000e: save skb counts in TX to avoid cache misses
In e1000_tx_map, precompute number of segements and bytecounts which
are derived from fields in skb; these are stored in buffer_info. When
cleaning tx in e1000_clean_tx_irq use the values in the associated
buffer_info for statistics counting, this eliminates cache misses
on skb fields.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Pavel Shilovsky [Thu, 10 May 2012 15:49:38 +0000 (19:49 +0400)]
fuse: fix stat call on 32 bit platforms
commit
45c72cd73c788dd18c8113d4a404d6b4a01decf1 upstream.
Now we store attr->ino at inode->i_ino, return attr->ino at the
first time and then return inode->i_ino if the attribute timeout
isn't expired. That's wrong on 32 bit platforms because attr->ino
is 64 bit and inode->i_ino is 32 bit in this case.
Fix this by saving 64 bit ino in fuse_inode structure and returning
it every time we call getattr. Also squash attr->ino into inode->i_ino
explicitly.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Borislav Petkov [Mon, 16 Apr 2012 16:01:53 +0000 (18:01 +0200)]
x86, MCE, AMD: Make APIC LVT thresholding interrupt optional
commit
f227d4306cf30e1d5b6f231e8ef9006c34f3d186 upstream.
Currently, the APIC LVT interrupt for error thresholding is implicitly
enabled. However, there are models in the F15h range which do not enable
it. Make the code machinery which sets up the APIC interrupt support
an optional setting and add an ->interrupt_capable member to the bank
representation mirroring that capability and enable the interrupt offset
programming only if it is true.
Simplify code and fixup comment style while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Emmanuel Grumbach [Wed, 6 Jun 2012 07:13:36 +0000 (09:13 +0200)]
iwlwifi: don't mess up the SCD when removing a key
commit
d6ee27eb13beab94056e0de52d81220058ca2297 upstream.
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dimitri Sivanich [Tue, 5 Jun 2012 18:44:36 +0000 (13:44 -0500)]
sched: Fix the relax_domain_level boot parameter
commit
a841f8cef4bb124f0f5563314d0beaf2e1249d72 upstream.
It does not get processed because sched_domain_level_max is 0 at the
time that setup_relax_domain_level() is run.
Simply accept the value as it is, as we don't know the value of
sched_domain_level_max until sched domain construction is completed.
Fix sched_relax_domain_level in cpuset. The build_sched_domain() routine calls
the set_domain_attribute() routine prior to setting the sd->level, however,
the set_domain_attribute() routine relies on the sd->level to decide whether
idle load balancing will be off/on.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120605184436.GA15668@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Cox [Wed, 25 Apr 2012 13:33:33 +0000 (14:33 +0100)]
acpi_video: fix leaking PCI references
commit
cfb46f433a4da97c31780e08a259fac2cb6bd61f upstream.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andre Przywara [Fri, 23 Mar 2012 09:02:17 +0000 (10:02 +0100)]
hwmon: (fam15h_power) Increase output resolution
commit
941a956b0e387b21f385f486c34ef67576775cfc upstream.
On high CPU load the accumulating values in the running_avg_cap
register are very low (below 10), so averaging them too early leads
to unnecessary poor output resolution. Since we pretend to output
micro-Watt we better keep all the bits we have as long as possible.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AnilKumar Ch [Wed, 23 May 2012 12:15:11 +0000 (17:45 +0530)]
can: c_can: fix race condition in c_can_open()
commit
f461f27a4436dbe691908fe08b867ef888848cc3 upstream.
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AnilKumar Ch [Wed, 23 May 2012 12:15:10 +0000 (17:45 +0530)]
can: c_can: fix an interrupt thrash issue with c_can driver
commit
148c87c89e1a8863d3d965179f3ab1a06490569e upstream.
This patch fixes an interrupt thrash issue with c_can driver.
In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.
To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AnilKumar Ch [Wed, 23 May 2012 12:15:09 +0000 (17:45 +0530)]
can: c_can: fix "BUG! echo_skb is occupied!" during transmit
commit
617caccebe451716df21c069b079d5936ed7b0f3 upstream.
This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.
In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.
As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.
Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.
While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Tue, 5 Jun 2012 21:18:10 +0000 (21:18 +0000)]
net: sierra_net: device IDs for Aircard 320U++
commit
dd03cff23d694cfb0fdae80cb618e7ced05ea696 upstream.
Adding device IDs for Aircard 320U and two other devices
found in the out-of-tree version of this driver.
Cc: linux@sierrawireless.com
Cc: Autif Khan <autif.mlist@gmail.com>
Cc: Tom Cassidy <tomas.cassidy@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Tue, 5 Jun 2012 10:16:50 +0000 (12:16 +0200)]
cfg80211: fix interface combinations check
commit
463454b5dbd8dbab6e2fc6c557329e5b811b9c32 upstream.
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Thu, 31 May 2012 13:09:27 +0000 (15:09 +0200)]
mac80211: clean up remain-on-channel on interface stop
commit
71ecfa1893034eeb1c93e02e22ee2ad26d080858 upstream.
When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.
It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Tue, 29 May 2012 23:43:08 +0000 (01:43 +0200)]
crypto: aesni-intel - fix unaligned cbc decrypt for x86-32
commit
7c8d51848a88aafdb68f42b6b650c83485ea2f84 upstream.
The 32 bit variant of cbc(aes) decrypt is using instructions requiring
128 bit aligned memory locations but fails to ensure this constraint in
the code. Fix this by loading the data into intermediate registers with
load unaligned instructions.
This fixes reported general protection faults related to aesni.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43223
Reported-by: Daniel <garkein@mailueberfall.de>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Rumler [Wed, 6 Jun 2012 14:37:17 +0000 (16:37 +0200)]
powerpc: Fix kernel panic during kernel module load
commit
3c75296562f43e6fbc6cddd3de948a7b3e4e9bcf upstream.
This fixes a problem which can causes kernel oopses while loading
a kernel module.
According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.
This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.
The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code. According to the statements from Freescale, this is
safe from an EABI perspective.
I've tested the fix for kernel 2.6.33 on MPC8541.
Signed-off-by: Steffen Rumler <steffen.rumler.ext@nsn.com>
[paulus@samba.org: reworded the description]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Dreier [Thu, 7 Jun 2012 21:21:13 +0000 (14:21 -0700)]
btree: fix tree corruption in btree_get_prev()
commit
cbf8ae32f66a9ceb8907ad9e16663c2a29e48990 upstream.
The memory the parameter __key points to is used as an iterator in
btree_get_prev(), so if we save off a bkey() pointer in retry_key and
then assign that to __key, we'll end up corrupting the btree internals
when we do eg
longcpy(__key, bkey(geo, node, i), geo->keylen);
to return the key value. What we should do instead is use longcpy() to
copy the key value that retry_key points to __key.
This can cause a btree to get corrupted by seemingly read-only
operations such as btree_for_each_safe.
[akpm@linux-foundation.org: avoid the double longcpy()]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eugeni Dodonov [Wed, 6 Jun 2012 14:59:06 +0000 (11:59 -0300)]
char/agp: add another Ironlake host bridge
commit
67384fe3fd450536342330f684ea1f7dcaef8130 upstream.
This seems to come on Gigabyte H55M-S2V and was discovered through the
https://bugs.freedesktop.org/show_bug.cgi?id=50381 debugging.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50381
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 9 Jun 2012 15:33:45 +0000 (00:33 +0900)]
Linux 3.0.34
Tao Ma [Thu, 7 Jun 2012 23:04:19 +0000 (19:04 -0400)]
ext4: don't set i_flags in EXT4_IOC_SETFLAGS
commit
b22b1f178f6799278d3178d894f37facb2085765 upstream.
Commit
7990696 uses the ext4_{set,clear}_inode_flags() functions to
change the i_flags automatically but fails to remove the error setting
of i_flags. So we still have the problem of trashing state flags.
Fix this by removing the assignment.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grazvydas Ignotas [Fri, 18 May 2012 00:04:08 +0000 (03:04 +0300)]
wl1251: fix oops on early interrupt
commit
f380f2c4a12e913356bd49f8790ec1063c4fe9f8 upstream.
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Whitcroft [Thu, 3 May 2012 13:48:26 +0000 (14:48 +0100)]
ACPI battery: only refresh the sysfs files when pertinent information changes
commit
c5971456964290da7e98222892797b71ef793e62 upstream.
We only need to regenerate the sysfs files when the capacity units
change, avoid the update otherwise.
The origin of this issue is dates way back to 2.6.38:
da8aeb92d4853f37e281f11fddf61f9c7d84c3cd
(ACPI / Battery: Update information on info notification and resume)
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Tested-by: Ralf Jung <post@ralfj.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Tue, 5 Jun 2012 13:50:30 +0000 (09:50 -0400)]
drm/radeon/kms: add new BTC PCI ids
commit
a2bef8ce826dd1e787fd8ad9b6e0566ba59dab43 upstream.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Salman Qazi [Fri, 1 Jun 2012 03:52:14 +0000 (23:52 -0400)]
ext4: remove mb_groups before tearing down the buddy_cache
commit
95599968d19db175829fb580baa6b68939b320fb upstream.
We can't have references held on pages in the s_buddy_cache while we are
trying to truncate its pages and put the inode. All the pages must be
gone before we reach clear_inode. This can only be gauranteed if we
can prevent new users from grabbing references to s_buddy_cache's pages.
The original bug can be reproduced and the bug fix can be verified by:
while true; do mount -t ext4 /dev/ram0 /export/hda3/ram0; \
umount /export/hda3/ram0; done &
while true; do cat /proc/fs/ext4/ram0/mb_groups; done
Signed-off-by: Salman Qazi <sqazi@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Salman Qazi [Fri, 1 Jun 2012 03:51:27 +0000 (23:51 -0400)]
ext4: add ext4_mb_unload_buddy in the error path
commit
02b7831019ea4e7994968c84b5826fa8b248ffc8 upstream.
ext4_free_blocks fails to pair an ext4_mb_load_buddy with a matching
ext4_mb_unload_buddy when it fails a memory allocation.
Signed-off-by: Salman Qazi <sqazi@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Fri, 1 Jun 2012 03:46:01 +0000 (23:46 -0400)]
ext4: don't trash state flags in EXT4_IOC_SETFLAGS
commit
79906964a187c405db72a3abc60eb9b50d804fbc upstream.
In commit
353eb83c we removed i_state_flags with 64-bit longs, But
when handling the EXT4_IOC_SETFLAGS ioctl, we replace i_flags
directly, which trashes the state flags which are stored in the high
32-bits of i_flags on 64-bit platforms. So use the the
ext4_{set,clear}_inode_flags() functions which use atomic bit
manipulation functions instead.
Reported-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Thu, 31 May 2012 03:00:16 +0000 (23:00 -0400)]
ext4: add missing save_error_info() to ext4_error()
commit
f3fc0210c0fc91900766c995f089c39170e68305 upstream.
The ext4_error() function is missing a call to save_error_info().
Since this is the function which marks the file system as containing
an error, this oversight (which was introduced in 2.6.36) is quite
significant, and should be backported to older stable kernels with
high urgency.
Reported-by: Ken Sumrall <ksumrall@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: ksumrall@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Sandeen [Mon, 28 May 2012 18:17:25 +0000 (14:17 -0400)]
ext4: force ro mount if ext4_setup_super() fails
commit
7e84b6216467b84cd332c8e567bf5aa113fd2f38 upstream.
If ext4_setup_super() fails i.e. due to a too-high revision,
the error is logged in dmesg but the fs is not mounted RO as
indicated.
Tested by:
# mkfs.ext4 -r 4 /dev/sdb6
# mount /dev/sdb6 /mnt/test
# dmesg | grep "too high"
[164919.759248] EXT4-fs (sdb6): revision level too high, forcing read-only mode
# grep sdb6 /proc/mounts
/dev/sdb6 /mnt/test2 ext4 rw,seclabel,relatime,data=ordered 0 0
Reviewed-by: Andreas Dilger <adilger@whamcloud.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Poirier [Thu, 24 May 2012 11:32:38 +0000 (11:32 +0000)]
xfrm: take net hdr len into account for esp payload size calculation
[ Upstream commit
91657eafb64b4cb53ec3a2fbc4afc3497f735788 ]
Corrects the function that determines the esp payload size. The calculations
done in esp{4,6}_get_mtu() lead to overlength frames in transport mode for
certain mtu values and suboptimal frames for others.
According to what is done, mainly in esp{,6}_output() and tcp_mtu_to_mss(),
net_header_len must be taken into account before doing the alignment
calculation.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Tue, 29 May 2012 03:35:08 +0000 (03:35 +0000)]
skb: avoid unnecessary reallocations in __skb_cow
[ Upstream commit
617c8c11236716dcbda877e764b7bf37c6fd8063 ]
At the beginning of __skb_cow, headroom gets set to a minimum of
NET_SKB_PAD. This causes unnecessary reallocations if the buffer was not
cloned and the headroom is just below NET_SKB_PAD, but still more than the
amount requested by the caller.
This was showing up frequently in my tests on VLAN tx, where
vlan_insert_tag calls skb_cow_head(skb, VLAN_HLEN).
Locally generated packets should have enough headroom, and for forward
paths, we already have NET_SKB_PAD bytes of headroom, so we don't need to
add any extra space here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Dichtel [Fri, 4 May 2012 05:24:54 +0000 (05:24 +0000)]
sctp: check cached dst before using it
[ Upstream commit
e0268868ba064980488fc8c194db3d8e9fb2959c ]
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vlad Yaseivch <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller [Fri, 11 May 2012 03:03:34 +0000 (23:03 -0400)]
Revert "net: maintain namespace isolation between vlan and real device"
[ Upstream commit
59b9997baba5242997ddc7bd96b1391f5275a5a4 ]
This reverts commit
8a83a00b0735190384a348156837918271034144.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Thu, 17 May 2012 23:52:26 +0000 (23:52 +0000)]
pktgen: fix module unload for good
[ Upstream commit
d4b1133558e0d417342d5d2c49e4c35b428ff20d ]
commit
c57b5468406 (pktgen: fix crash at module unload) did a very poor
job with list primitives.
1) list_splice() arguments were in the wrong order
2) list_splice(list, head) has undefined behavior if head is not
initialized.
3) We should use the list_splice_init() variant to clear pktgen_threads
list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Wed, 9 May 2012 13:29:51 +0000 (13:29 +0000)]
pktgen: fix crash at module unload
[ Upstream commit
c57b54684060c8aced64a5b78ff69ff289af97b9 ]
commit
7d3d43dab4e9 (net: In unregister_netdevice_notifier unregister
the netdevices.) makes pktgen crashing at module unload.
[ 296.820578] BUG: spinlock bad magic on CPU#6, rmmod/3267
[ 296.820719] lock:
ffff880310c38000, .magic:
ffff8803, .owner: <none>/-1, .owner_cpu: -1
[ 296.820943] Pid: 3267, comm: rmmod Not tainted 3.4.0-rc5+ #254
[ 296.821079] Call Trace:
[ 296.821211] [<
ffffffff8168a715>] spin_dump+0x8a/0x8f
[ 296.821345] [<
ffffffff8168a73b>] spin_bug+0x21/0x26
[ 296.821507] [<
ffffffff812b4741>] do_raw_spin_lock+0x131/0x140
[ 296.821648] [<
ffffffff8169188e>] _raw_spin_lock+0x1e/0x20
[ 296.821786] [<
ffffffffa00cc0fd>] __pktgen_NN_threads+0x4d/0x140 [pktgen]
[ 296.821928] [<
ffffffffa00ccf8d>] pktgen_device_event+0x10d/0x1e0 [pktgen]
[ 296.822073] [<
ffffffff8154ed4f>] unregister_netdevice_notifier+0x7f/0x100
[ 296.822216] [<
ffffffffa00d2a0b>] pg_cleanup+0x48/0x73 [pktgen]
[ 296.822357] [<
ffffffff8109528e>] sys_delete_module+0x17e/0x2a0
[ 296.822502] [<
ffffffff81699652>] system_call_fastpath+0x16/0x1b
Hold the pktgen_thread_lock while splicing pktgen_threads, and test
pktgen_exiting in pktgen_device_event() to make unload faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Chapman [Tue, 29 May 2012 23:13:23 +0000 (23:13 +0000)]
l2tp: fix oops in L2TP IP sockets for connect() AF_UNSPEC case
[ Upstream commit
c51ce49735c183ef2592db70f918ee698716276b ]
An application may call connect() to disconnect a socket using an
address with family AF_UNSPEC. The L2TP IP sockets were not handling
this case when the socket is not bound and an attempt to connect()
using AF_UNSPEC in such cases would result in an oops. This patch
addresses the problem by protecting the sk_prot->disconnect() call
against trying to unhash the socket before it is bound.
The patch also adds more checks that the sockaddr supplied to bind()
and connect() calls is valid.
RIP: 0010:[<
ffffffff82e133b0>] [<
ffffffff82e133b0>] inet_unhash+0x50/0xd0
RSP: 0018:
ffff88001989be28 EFLAGS:
00010293
Stack:
ffff8800407a8000 0000000000000000 ffff88001989be78 ffffffff82e3a249
ffffffff82e3a050 ffff88001989bec8 ffff88001989be88 ffff8800407a8000
0000000000000010 ffff88001989bec8 ffff88001989bea8 ffffffff82e42639
Call Trace:
[<
ffffffff82e3a249>] udp_disconnect+0x1f9/0x290
[<
ffffffff82e42639>] inet_dgram_connect+0x29/0x80
[<
ffffffff82d012fc>] sys_connect+0x9c/0x100
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gao feng [Sat, 26 May 2012 01:30:53 +0000 (01:30 +0000)]
ipv6: fix incorrect ipsec fragment
[ Upstream commit
0c1833797a5a6ec23ea9261d979aa18078720b74 ]
Since commit
ad0081e43a
"ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed"
the fragment of packets is incorrect.
because tunnel mode needs IPsec headers and trailer for all fragments,
while on transport mode it is sufficient to add the headers to the
first fragment and the trailer to the last.
so modify mtu and maxfraglen base on ipsec mode and if fragment is first
or last.
with my test,it work well(every fragment's size is the mtu)
and does not trigger slow fragment path.
Changes from v1:
though optimization, mtu_prev and maxfraglen_prev can be delete.
replace xfrm mode codes with dst_entry's new frag DST_XFRM_TUNNEL.
add fuction ip6_append_data_mtu to make codes clearer.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yanmin Zhang [Wed, 23 May 2012 15:39:45 +0000 (15:39 +0000)]
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
[ Upstream commit
e49cc0da7283088c5e03d475ffe2fdcb24a6d5b1 ]
We hit a kernel OOPS.
<3>[23898.789643] BUG: sleeping function called from invalid context at
/data/buildbot/workdir/ics/hardware/intel/linux-2.6/arch/x86/mm/fault.c:1103
<3>[23898.862215] in_atomic(): 0, irqs_disabled(): 0, pid: 10526, name:
Thread-6683
<4>[23898.967805] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.258526] Pid: 10526, comm: Thread-6683 Tainted: G W
3.0.8-137685-ge7742f9 #1
<4>[23899.357404] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.904225] Call Trace:
<4>[23899.989209] [<
c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.000416] [<
c1238c2a>] __might_sleep+0x10a/0x110
<4>[23900.007357] [<
c1228021>] do_page_fault+0xd1/0x3c0
<4>[23900.013764] [<
c18e9ba9>] ? restore_all+0xf/0xf
<4>[23900.024024] [<
c17c007b>] ? napi_complete+0x8b/0x690
<4>[23900.029297] [<
c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.123739] [<
c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.128955] [<
c18ea0c3>] error_code+0x5f/0x64
<4>[23900.133466] [<
c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.138450] [<
c17f6298>] ? __ip_route_output_key+0x698/0x7c0
<4>[23900.144312] [<
c17f5f8d>] ? __ip_route_output_key+0x38d/0x7c0
<4>[23900.150730] [<
c17f63df>] ip_route_output_flow+0x1f/0x60
<4>[23900.156261] [<
c181de58>] ip4_datagram_connect+0x188/0x2b0
<4>[23900.161960] [<
c18e981f>] ? _raw_spin_unlock_bh+0x1f/0x30
<4>[23900.167834] [<
c18298d6>] inet_dgram_connect+0x36/0x80
<4>[23900.173224] [<
c14f9e88>] ? _copy_from_user+0x48/0x140
<4>[23900.178817] [<
c17ab9da>] sys_connect+0x9a/0xd0
<4>[23900.183538] [<
c132e93c>] ? alloc_file+0xdc/0x240
<4>[23900.189111] [<
c123925d>] ? sub_preempt_count+0x3d/0x50
Function free_fib_info resets nexthop_nh->nh_dev to NULL before releasing
fi. Other cpu might be accessing fi. Fixing it by delaying the releasing.
With the patch, we ran MTBF testing on Android mobile for 12 hours
and didn't trigger the issue.
Thank Eric for very detailed review/checking the issue.
Signed-off-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: Kun Jiang <kunx.jiang@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller [Fri, 11 May 2012 02:16:32 +0000 (22:16 -0400)]
ipv4: Do not use dead fib_info entries.
[ Upstream commit
dccd9ecc374462e5d6a5b8f8110415a86c2213d8 ]
Due to RCU lookups and RCU based release, fib_info objects can
be found during lookup which have fi->fib_dead set.
We must ignore these entries, otherwise we risk dereferencing
the parts of the entry which are being torn down.
Reported-by: Yevgen Pronenko <yevgen.pronenko@sonymobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Hellstrom [Fri, 1 Jun 2012 13:39:11 +0000 (15:39 +0200)]
drm/ttm: Fix spinlock imbalance
commit
a8ff3ee211fccf708e1911bbc096625453ebf759 upstream.
This imbalance may cause hangs when TTM is trying to swap out a buffer
that is already on the delayed delete list.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jerome Glisse [Thu, 31 May 2012 23:00:24 +0000 (19:00 -0400)]
drm/radeon: fix HD6790, HD6570 backend programming
commit
95c4b23ec4e2fa5604df229ddf134e31d7b3b378 upstream.
Without this bit sets we get broken rendering and
lockups.
fglrx sets this bit.
Bugs that should be fixed by this patch :
https://bugs.freedesktop.org/show_bug.cgi?id=49792
https://bugzilla.kernel.org/show_bug.cgi?id=43207
https://bugs.freedesktop.org/show_bug.cgi?id=39282
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Thu, 31 May 2012 22:54:43 +0000 (18:54 -0400)]
drm/radeon: properly program gart on rv740, juniper, cypress, barts, hemlock
commit
0b8c30bc4943137a4a36b9cb059b1cc684f5d702 upstream.
Need to program an additional VM register. This doesn't not currently
cause any problems, but allows us to program the proper backend
map in a subsequent patch which should improve performance on these
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Maluka [Fri, 11 May 2012 17:51:51 +0000 (20:51 +0300)]
mtd: nand: fix scan_read_raw_oob
commit
34a5704d91d6f8376a4c0a0143a1dd3eb3ccb37e upstream.
It seems there is a bug in scan_read_raw_oob() in nand_bbt.c which
should cause wrong functioning of NAND_BBT_SCANALLPAGES option.
Artem: the patch did not apply and I had to amend it a bit.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Wed, 30 May 2012 02:03:48 +0000 (22:03 -0400)]
vfs: umount_tree() might be called on subtree that had never made it
commit
63d37a84ab6004c235314ffd7a76c5eb28c2fae0 upstream.
__mnt_make_shortterm() in there undoes the effect of __mnt_make_longterm()
we'd done back when we set ->mnt_ns non-NULL; it should not be done to
vfsmounts that had never gone through commit_tree() and friends. Kudos to
lczerner for catching that one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clemens Ladisch [Fri, 18 May 2012 16:00:43 +0000 (18:00 +0200)]
ALSA: usb-audio: fix rate_list memory leak
commit
5cd5d7c44990658df6ab49f6253c39617c53b03d upstream.
The array of sample rates is reallocated every time when opening
the PCM device, but was freed only once when unplugging the device.
Reported-by: "Alexander E. Patrakov" <patrakov@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Gruetzner [Wed, 2 May 2012 20:33:40 +0000 (22:33 +0200)]
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
commit
85d59726c5c66016a507f1f4a60db8e374dd284d upstream.
Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to
the blacklist of btusb module and add it to the ath3k module to properly
load the firmware in Kernel 3.3.4
The device is integrated in e.g. some Acer Aspire 7750G.
Output from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e03c Rev= 0.02
S: Manufacturer=Atheros Communications
S: Product=Bluetooth USB Host Controller
S: SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Michael Gruetzner <mgruetzn@gmx.de>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Harms [Fri, 13 Apr 2012 18:45:55 +0000 (14:45 -0400)]
Add Foxconn / Hon Hai IDs for btusb module
commit
985140369be1e886754d8ac0375dd64e4f727311 upstream.
This change adds 0x0489:0xe033 to the btusb module.
This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook.
Output from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e033 Rev= 2.29
S: Manufacturer=Broadcom Corp
S: Product=Acer Module
S: SerialNumber=
60D819F74101
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Steven Harms <sjharms@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don Zickus [Wed, 28 Mar 2012 20:41:11 +0000 (16:41 -0400)]
Bluetooth: btusb: typo in Broadcom SoftSailing id
commit
2e8b506310f6433d5558387fd568d4bfb1d6a799 upstream.
I was trying to backport the following commit to RHEL-6
From
0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
and noticed it wasn't working on an HP Elitebook. Looking into the patch I
noticed a very subtle typo in the ids. The patch has '0x05ac' instead of
'0x0a5c'. A snippet of the lsusb -v output also shows this:
Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 1
bDeviceProtocol 1
bMaxPacketSize0 64
idVendor 0x0a5c Broadcom Corp.
idProduct 0x21e1
bcdDevice 1.12
iManufacturer 1 Broadcom Corp
iProduct 2 BCM20702A0
iSerial 3
60D819F0338C
bNumConfigurations 1
Looking at other Broadcom ids, the fix matches them whereas the original patch
matches Apple's ids.
Tested on an HP Elitebook 8760w. The btusb binds and the userspace stuff loads
correctly.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Manoj Iyer [Mon, 9 Apr 2012 14:22:28 +0000 (09:22 -0500)]
Bluetooth: btusb: Add vendor specific ID (0489 e042) for BCM20702A0
commit
79cd76022044f8177bb00e3fd590ec8d6b5f8c35 upstream.
T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e042 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=
E4D53DCA61B5
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Reported-by: Dennis Chua <dennis.chua@canonical.com>
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
João Paulo Rechi Vita [Wed, 14 Mar 2012 19:45:16 +0000 (21:45 +0200)]
Bluetooth: btusb: Add USB device ID "0a5c 21e8"
commit
6dfc326f0605fd87e4c10ccde10de0ce4280d72d upstream.
One more vendor-specific ID for BCM20702A0.
T: Bus=01 Lev=03 Prnt=05 Port=02 Cnt=01 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e8 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=
00027221F4E2
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James M. Leddy [Tue, 6 Mar 2012 00:41:33 +0000 (02:41 +0200)]
Bluetooth: btusb: add support for BCM20702A0 [0a5c:21e6]
commit
0a4eaeeb993658a4d6cff054a863241f32d3d2fb upstream.
Add another vendor specific ID for BCM20702A0. This has been tested and
works on hardware with this device.
output of usb-devices:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=04 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e6 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=
D0DF9AFB227B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: James M. Leddy <james.leddy@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Manoj Iyer [Thu, 2 Feb 2012 15:32:36 +0000 (09:32 -0600)]
Bluetooth: btusb: Add vendor specific ID (0a5c 21f3) for BCM20702A0
commit
37305cf649689a4d2341dd6fd89b091c6007f9ba upstream.
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=
74DE2B344A7B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Dennis Chua <dennis.chua@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesse Sung [Thu, 22 Dec 2011 02:48:47 +0000 (10:48 +0800)]
Bluetooth: Add support for BCM20702A0 [0a5c:21e3]
commit
c0190925dacd976a67044f4382d4effbed568dce upstream.
Add another vendor specific ID for BCM20702A0.
output of usb-devices:
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=
9439E5CBF66C
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wen-chien Jesse Sung [Tue, 8 Nov 2011 06:30:22 +0000 (14:30 +0800)]
Bluetooth: Add support for Broadcom BCM20702A0
commit
d13431ca3eb2a2c14314f04813cdc11cd869f150 upstream.
Since this device declares itself as vendor specific, must add
a new entry to device ID table to support it.
usb-device output of this device:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=413c ProdID=8197 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=
D0DF9AA9C9F1
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Tue, 22 May 2012 19:41:25 +0000 (21:41 +0200)]
drm/i915: wait for a vblank to pass after tv detect
commit
bf2125e2f7e931b50a6c76ba0435ba001409ccbf upstream.
Otherwise the hw will get confused and result in a black screen.
This regression has been most likely introduce in
commit
974b93315b2213b74a42a87e8a9d4fc8c0dbe90c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Sep 5 00:44:20 2010 +0100
drm/i915/tv: Poll for DAC state change
That commit replace the first msleep(20) with a busy-loop, but failed
to keep the 2nd msleep around. Later on we've replaced all these
msleep(20) by proper vblanks.
For reference also see the commit in xf86-video-intel:
commit
1142be53eb8d2ee8a9b60ace5d49f0ba27332275
Author: Jesse Barnes <jbarnes@hobbes.lan>
Date: Mon Jun 9 08:52:59 2008 -0700
Fix TV programming: add vblank wait after TV_CTL writes
Fxies FDO bug #14000; we need to wait for vblank after
writing TV_CTL or following "DPMS on" calls may not actually enable the output.
v2: As suggested by Chris Wilson, add a small comment to ensure that
no one accidentally removes this vblank wait again - there really
seems to be no sane explanation for why we need it, but it is
required.
Launchpad: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/763688
Reported-and-Tested-by: Robert Lowery <rglowery@exemail.com.au>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Sat, 12 May 2012 20:22:58 +0000 (22:22 +0200)]
drm/i915: properly handle interlaced bit for sdvo dtd conversion
commit
59d92bfa5f0cdf57f82f5181b0ad6af75c3fdf41 upstream.
We've simply ignored this, which isn't too great. With this, interlaced
1080i works on my HDMI screen connected through sdvo. For no apparent
reason anything else still doesn't work as it should.
While at it, give these magic numbers in the dtd proper names and
add a comment that they match with EDID detailed timings.
v2: Actually use the right bit for interlaced.
Tested-by: Peter Ross <pross@xvid.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Wed, 23 May 2012 15:48:59 +0000 (11:48 -0400)]
drm/radeon: fix XFX quirk
commit
1ebf169ad4dc68f18cc0dab35163b0f324fc6c41 upstream.
Only override the ddc bus if the connector doesn't have
a valid one. The existing code overrode the ddc bus for
all connectors even if it had ddc bus.
Fixes ddc on another XFX card with the same pci ids that
was broken by the quirk overwriting the correct ddc bus.
Reported-by: Mehdi Aqadjani Memar <m.aqadjanimemar@student.ru.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Mon, 28 May 2012 15:36:28 +0000 (11:36 -0400)]
NFSv4: Map NFS4ERR_SHARE_DENIED into an EACCES error instead of EIO
commit
fb13bfa7e1bcfdcfdece47c24b62f1a1cad957e9 upstream.
If a file OPEN is denied due to a share lock, the resulting
NFS4ERR_SHARE_DENIED is currently mapped to the default EIO.
This patch adds a more appropriate mapping, and brings Linux
into line with what Solaris 10 does.
See https://bugzilla.kernel.org/show_bug.cgi?id=43286
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eyal Shapira [Tue, 29 May 2012 09:00:22 +0000 (02:00 -0700)]
mac80211: fix ADDBA declined after suspend with wowlan
commit
7b21aea04d084916ac4e0e8852dcc9cd60ec0d1d upstream.
WLAN_STA_BLOCK_BA is set while suspending but doesn't get cleared
when resuming in case of wowlan. This causes further ADDBA requests
received to be rejected. Fix it by clearing it in the wowlan path
as well.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Woodhouse [Thu, 24 May 2012 04:58:27 +0000 (04:58 +0000)]
solos-pci: Fix DMA support
commit
b4bd8ad9bb311e8536f726f7a633620ccd358cde upstream.
DMA support has finally made its way to the top of the TODO list, having
realised that a Geode using MMIO can't keep up with two ADSL2+ lines
each running at 21Mb/s.
This patch fixes a couple of bugs in the DMA support in the driver, so
once the corresponding FPGA update is complete and tested everything
should work properly.
We weren't storing the currently-transmitting skb, so we were never
unmapping it and never freeing/popping it when the TX was done.
And the addition of pci_set_master() is fairly self-explanatory.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Mon, 21 May 2012 06:49:01 +0000 (07:49 +0100)]
PARISC: fix TLB fault path on PA2.0 narrow systems
commit
2f649c1f6f0fef445ce79a19b79e5ce8fe9d7f19 upstream.
commit
5e185581d7c46ddd33cd9c01106d1fc86efb9376
Author: James Bottomley <JBottomley@Parallels.com>
[PARISC] fix PA1.1 oops on boot
Didn't quite fix the crash on boot. It moved it from PA1.1 processors to
PA2.0 narrow kernels. The final fix is to make sure the [id]tlb_miss_20 paths
also work. Even on narrow systems, these paths require using the wide
instructions becuase the tlb insertion format is wide. Fix this by
conditioning the dep[wd],z on whether we're being called from _11 or _20[w]
paths.
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John David Anglin [Thu, 17 May 2012 14:34:34 +0000 (10:34 -0400)]
PARISC: fix boot failure on 32-bit systems caused by branch stubs placed before .text
commit
ed5fb2471b7060767957fb964eb1aaec71533ab1 upstream.
In certain configurations, the resulting kernel becomes too large to boot
because the linker places the long branch stubs for the merged .text section
at the very start of the image. As a result, the initial transfer of control
jumps to an unexpected location. Fix this by placing the head text in a
separate section so the stubs for .text are not at the start of the image.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shirish Pargaonkar [Mon, 21 May 2012 14:20:12 +0000 (09:20 -0500)]
cifs: fix oops while traversing open file list (try #4)
commit
2c0c2a08bed7a3b791f88d09d16ace56acb3dd98 upstream.
While traversing the linked list of open file handles, if the identfied
file handle is invalid, a reopen is attempted and if it fails, we
resume traversing where we stopped and cifs can oops while accessing
invalid next element, for list might have changed.
So mark the invalid file handle and attempt reopen if no
valid file handle is found in rest of the list.
If reopen fails, move the invalid file handle to the end of the list
and start traversing the list again from the begining.
Repeat this four times before giving up and returning an error if
file reopen keeps failing.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Meenakshi Venkataraman [Wed, 16 May 2012 20:35:57 +0000 (22:35 +0200)]
iwlwifi: update BT traffic load states correctly
commit
882dde8eb0d49ce0f853f8f4084dde56a21fe55f upstream.
When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrea Arcangeli [Tue, 29 May 2012 22:06:49 +0000 (15:06 -0700)]
mm: pmd_read_atomic: fix 32bit PAE pmd walk vs pmd_populate SMP race condition
commit
26c191788f18129af0eb32a358cdaea0c7479626 upstream.
When holding the mmap_sem for reading, pmd_offset_map_lock should only
run on a pmd_t that has been read atomically from the pmdp pointer,
otherwise we may read only half of it leading to this crash.
PID: 11679 TASK:
f06e8000 CPU: 3 COMMAND: "do_race_2_panic"
#0 [
f06a9dd8] crash_kexec at
c049b5ec
#1 [
f06a9e2c] oops_end at
c083d1c2
#2 [
f06a9e40] no_context at
c0433ded
#3 [
f06a9e64] bad_area_nosemaphore at
c043401a
#4 [
f06a9e6c] __do_page_fault at
c0434493
#5 [
f06a9eec] do_page_fault at
c083eb45
#6 [
f06a9f04] error_code (via page_fault) at
c083c5d5
EAX:
01fb470c EBX:
fff35000 ECX:
00000003 EDX:
00000100 EBP:
00000000
DS: 007b ESI:
9e201000 ES: 007b EDI:
01fb4700 GS: 00e0
CS: 0060 EIP:
c083bc14 ERR:
ffffffff EFLAGS:
00010246
#7 [
f06a9f38] _spin_lock at
c083bc14
#8 [
f06a9f44] sys_mincore at
c0507b7d
#9 [
f06a9fb0] system_call at
c083becd
start len
EAX:
ffffffda EBX:
9e200000 ECX:
00001000 EDX:
6228537f
DS: 007b ESI:
00000000 ES: 007b EDI:
003d0f00
SS: 007b ESP:
62285354 EBP:
62285388 GS: 0033
CS: 0073 EIP:
00291416 ERR:
000000da EFLAGS:
00000286
This should be a longstanding bug affecting x86 32bit PAE without THP.
Only archs with 64bit large pmd_t and 32bit unsigned long should be
affected.
With THP enabled the barrier() in pmd_none_or_trans_huge_or_clear_bad()
would partly hide the bug when the pmd transition from none to stable,
by forcing a re-read of the *pmd in pmd_offset_map_lock, but when THP is
enabled a new set of problem arises by the fact could then transition
freely in any of the none, pmd_trans_huge or pmd_trans_stable states.
So making the barrier in pmd_none_or_trans_huge_or_clear_bad()
unconditional isn't good idea and it would be a flakey solution.
This should be fully fixed by introducing a pmd_read_atomic that reads
the pmd in order with THP disabled, or by reading the pmd atomically
with cmpxchg8b with THP enabled.
Luckily this new race condition only triggers in the places that must
already be covered by pmd_none_or_trans_huge_or_clear_bad() so the fix
is localized there but this bug is not related to THP.
NOTE: this can trigger on x86 32bit systems with PAE enabled with more
than 4G of ram, otherwise the high part of the pmd will never risk to be
truncated because it would be zero at all times, in turn so hiding the
SMP race.
This bug was discovered and fully debugged by Ulrich, quote:
----
[..]
pmd_none_or_trans_huge_or_clear_bad() loads the content of edx and
eax.
496 static inline int pmd_none_or_trans_huge_or_clear_bad(pmd_t
*pmd)
497 {
498 /* depend on compiler for an atomic pmd read */
499 pmd_t pmdval = *pmd;
// edi = pmd pointer
0xc0507a74 <sys_mincore+548>: mov 0x8(%esp),%edi
...
// edx = PTE page table high address
0xc0507a84 <sys_mincore+564>: mov 0x4(%edi),%edx
...
// eax = PTE page table low address
0xc0507a8e <sys_mincore+574>: mov (%edi),%eax
[..]
Please note that the PMD is not read atomically. These are two "mov"
instructions where the high order bits of the PMD entry are fetched
first. Hence, the above machine code is prone to the following race.
- The PMD entry {high|low} is 0x0000000000000000.
The "mov" at 0xc0507a84 loads 0x00000000 into edx.
- A page fault (on another CPU) sneaks in between the two "mov"
instructions and instantiates the PMD.
- The PMD entry {high|low} is now 0x00000003fda38067.
The "mov" at 0xc0507a8e loads 0xfda38067 into eax.
----
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Hocko [Tue, 29 May 2012 22:06:45 +0000 (15:06 -0700)]
mm: consider all swapped back pages in used-once logic
commit
e48982734ea0500d1eba4f9d96195acc5406cad6 upstream.
Commit
645747462435 ("vmscan: detect mapped file pages used only once")
made mapped pages have another round in inactive list because they might
be just short lived and so we could consider them again next time. This
heuristic helps to reduce pressure on the active list with a streaming
IO worklods.
This patch fixes a regression introduced by this commit for heavy shmem
based workloads because unlike Anon pages, which are excluded from this
heuristic because they are usually long lived, shmem pages are handled
as a regular page cache.
This doesn't work quite well, unfortunately, if the workload is mostly
backed by shmem (in memory database sitting on 80% of memory) with a
streaming IO in the background (backup - up to 20% of memory). Anon
inactive list is full of (dirty) shmem pages when watermarks are hit.
Shmem pages are kept in the inactive list (they are referenced) in the
first round and it is hard to reclaim anything else so we reach lower
scanning priorities very quickly which leads to an excessive swap out.
Let's fix this by excluding all swap backed pages (they tend to be long
lived wrt. the regular page cache anyway) from used-once heuristic and
rather activate them if they are referenced.
The customer's workload is shmem backed database (80% of RAM) and they
are measuring transactions/s with an IO in the background (20%).
Transactions touch more or less random rows in the table. The
transaction rate fell by a factor of 3 (in the worst case) because of
commit
64574746. This patch restores the previous numbers.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan@kernel.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jun'ichi Nomura [Tue, 22 May 2012 09:57:17 +0000 (18:57 +0900)]
SCSI: Fix dm-multipath starvation when scsi host is busy
commit
b7e94a1686c5daef4f649f7f4f839cc294f07710 upstream.
block congestion control doesn't have any concept of fairness across
multiple queues. This means that if SCSI reports the host as busy in
the queue congestion control it can result in an unfair starvation
situation in dm-mp if there are multiple multipath devices on the same
host. For example:
http://www.redhat.com/archives/dm-devel/2012-May/msg00123.html
The fix for this is to report only the sdev busy state (and ignore the
host busy state) in the block congestion control call back.
The host is still congested, but the SCSI subsystem will sort out the
congestion in a fair way because it knows the relation between the
queues and the host.
[jejb: fixed up trailing whitespace]
Reported-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Tested-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Wed, 30 May 2012 09:45:39 +0000 (09:45 +0000)]
SCSI: fix scsi_wait_scan
commit
1ff2f40305772b159a91c19590ee159d3a504afc upstream.
Commit
c751085943362143f84346d274e0011419c84202
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sun Apr 12 20:06:56 2009 +0200
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Broke the scsi_wait_scan module in 2.6.30. Apparently debian still uses it so
fix it and backport to stable before removing it in 3.6.
The breakage is caused because the function template in
include/scsi/scsi_scan.h is defined to be a nop unless SCSI is built in.
That means that in the modular case (which is every distro), the
scsi_wait_scan module does a simple async_synchronize_full() instead of
waiting for scans.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 1 Jun 2012 07:13:34 +0000 (15:13 +0800)]
Linux 3.0.33
Marcus Folkesson [Thu, 3 May 2012 13:56:36 +0000 (15:56 +0200)]
i2c: davinci: Free requested IRQ in remove
commit
9868a060ccf769c08ec378a9829137e272e9a92c upstream.
The freed IRQ is not necessary the one requested in probe.
Even if it was, with two or more i2c-controllers it will fails anyway.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dima Zavin [Mon, 30 Apr 2012 09:26:14 +0000 (10:26 +0100)]
ARM: 7409/1: Do not call flush_cache_user_range with mmap_sem held
commit
435a7ef52db7d86e67a009b36cac1457f8972391 upstream.
We can't be holding the mmap_sem while calling flush_cache_user_range
because the flush can fault. If we fault on a user address, the
page fault handler will try to take mmap_sem again. Since both places
acquire the read lock, most of the time it succeeds. However, if another
thread tries to acquire the write lock on the mmap_sem (e.g. mmap) in
between the call to flush_cache_user_range and the fault, the down_read
in do_page_fault will deadlock.
[will: removed drop of vma parameter as already queued by rmk (7365/1)]
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dima Zavin [Thu, 29 Mar 2012 19:44:06 +0000 (20:44 +0100)]
ARM: 7365/1: drop unused parameter from flush_cache_user_range
commit
4542b6a0fa6b48d9ae6b41c1efeb618b7a221b2a upstream.
vma isn't used and flush_cache_user_range isn't a standard macro that
is used on several archs with the same prototype. In fact only unicore32
has a macro with the same name (with an identical implementation and no
in-tree users).
This is a part of a patch proposed by Dima Zavin (with Message-id:
1272439931-12795-1-git-send-email-dima@android.com) that didn't get
accepted.
Cc: Dima Zavin <dima@android.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Mon, 30 Apr 2012 18:57:44 +0000 (11:57 -0700)]
isci: fix oem parameter validation on single controller skus
commit
fc25f79af321c01a739150ba2c09435cf977a63d upstream.
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Metcalf [Fri, 25 May 2012 16:32:09 +0000 (12:32 -0400)]
tile: fix bug where fls(0) was not returning 0
commit
9f1d62bed7f015d11b9164078b7fea433b474114 upstream.
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Pitre [Mon, 16 Apr 2012 23:16:54 +0000 (19:16 -0400)]
mmc: sdio: avoid spurious calls to interrupt handlers
commit
bbbc4c4d8c5face097d695f9bf3a39647ba6b7e7 upstream.
Commit
06e8935feb ("optimized SDIO IRQ handling for single irq")
introduced some spurious calls to SDIO function interrupt handlers,
such as when the SDIO IRQ thread is started, or the safety check
performed upon a system resume. Let's add a flag to perform the
optimization only when a real interrupt is signaled by the host
driver and we know there is no point confirming it.
Reported-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Luck [Wed, 23 May 2012 21:14:22 +0000 (14:14 -0700)]
x86/mce: Fix check for processor context when machine check was taken.
commit
875e26648cf9b6db9d8dc07b7959d7c61fb3f49c upstream.
Linus pointed out that there was no value is checking whether m->ip
was zero - because zero is a legimate value. If we have a reliable
(or faked in the VM86 case) "m->cs" we can use it to tell whether we
were in user mode or kernelwhen the machine check hit.
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Pinchart [Wed, 21 Mar 2012 12:50:36 +0000 (09:50 -0300)]
media: uvcvideo: Fix ENUMINPUT handling
commit
31c5f0c5e25ed71eeced170f113bb590f2f1f6f3 upstream.
Properly validate the user-supplied index against the number of inputs.
The code used the pin local variable instead of the index by mistake.
Reported-by: Jozef Vesely <vesely@gjh.sk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Krufky [Thu, 22 Mar 2012 16:55:05 +0000 (13:55 -0300)]
smsusb: add autodetection support for USB ID 2040:c0a0
commit
4d1b58b84472d1d300a66e1c5fd765b21e74ba15 upstream.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Airlie [Fri, 18 May 2012 14:31:12 +0000 (15:31 +0100)]
nouveau: nouveau_set_bo_placement takes TTM flags
commit
c284815debba2f14ee2fd07b1b4cc972ab116110 upstream.
This seems to be wrong to me, spotted while thinking about dma-buf.
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Sun, 13 May 2012 20:29:25 +0000 (22:29 +0200)]
drm/i915: don't clobber the pipe param in sanitize_modesetting
commit
a9dcf84b14ef4e9a609910367576995e6f32f3dc upstream.
... we need it later on in the function to clean up pipe <-> plane
associations. This regression has been introduced in
commit
f47166d2b0001fcb752b40c5a2d4db986dfbea68
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Mar 22 15:00:50 2012 +0000
drm/i915: Sanitize BIOS debugging bits from PIPECONF
Spotted by staring at debug output of an (as it turns out) totally
unrelated bug.
v2: I've totally failed to do the s/pipe/i/ correctly, spotted by
Chris Wilson.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Widawsky [Sun, 15 Apr 2012 01:41:32 +0000 (18:41 -0700)]
drm/i915: [GEN7] Use HW scheduler for fixed function shaders
commit
a1e969e0332de7a430e62822cee8f2ec8d83cd7c upstream.
This originally started as a patch from Bernard as a way of simply
setting the VS scheduler. After submitting the RFC patch, we decided to
also modify the DS scheduler. To be most explicit, I've made the patch
explicitly set all scheduler modes, and included the defines for other
modes (in case someone feels frisky later).
The rest of the story gets a bit weird. The first version of the patch
showed an almost unbelievable performance improvement. Since rebasing my
branch it appears the performance improvement has gone, unfortunately.
But setting these bits seem to be the right thing to do given that the
docs describe corruption that can occur with the default settings.
In summary, I am seeing no more perf improvements (or regressions) in my
limited testing, but we believe this should be set to prevent rendering
corruption, therefore cc stable.
v1: Clear bit 4 also (Ken + Eugeni)
Do a full clear + set of the bits we want (Me).
Cc: Bernard Kilarski <bernard.r.kilarski@intel.com>
Reviewed-by (RFC): Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Wilson [Wed, 9 May 2012 20:45:43 +0000 (21:45 +0100)]
drm/i915: Avoid a double-read of PCH_IIR during interrupt handling
commit
9adab8b5a7fde248504f484e197589f3e3c922e2 upstream.
Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Tue, 8 May 2012 16:22:49 +0000 (09:22 -0700)]
xhci: Add new short TX quirk for Fresco Logic host.
commit
1530bbc6272d9da1e39ef8e06190d42c13a02733 upstream.
Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic". When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine. The device is:
Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset
The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.
The successful completion code and non-zero untransferred length is a
contradiction. The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred. Otherwise, the transfer
should be marked with a short packet completion code. Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length. With it, we know to trust
the untransferred length.
Add a new xHCI quirk for the Fresco Logic host controller. If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning. For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.
This should be backported to stable kernels that contain the commit
f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some
Fresco Logic hosts." That commit was marked for stable kernels as old
as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergio Correia <lists@uece.net>
Tested-by: Sergio Correia <lists@uece.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Tue, 8 May 2012 14:09:26 +0000 (07:09 -0700)]
xhci: Reset reserved command ring TRBs on cleanup.
commit
33b2831ac870d50cc8e01c317b07fb1e69c13fe1 upstream.
When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero. Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.
This patch should be backported to kernels as old as 2.6.32,
that contain the commit
913a8a344ffcaf0b4a586d6662a2c66a7106557d
"USB: xhci: Change how xHCI commands are handled."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Mon, 23 Apr 2012 13:06:09 +0000 (15:06 +0200)]
usb-xhci: Handle COMP_TX_ERR for isoc tds
commit
9c745995ae5c4ff787f34a359de908facc11ee00 upstream.
While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.
The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().
This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.
This patch should be backported to kernels as old as 2.6.36, which contain the
commit
04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Thu, 9 Feb 2012 23:55:13 +0000 (15:55 -0800)]
xhci: Add Lynx Point to list of Intel switchable hosts.
commit
1c12443ab8eba71a658fae4572147e56d1f84f66 upstream.
The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host. This time, ports from both EHCI
hosts can be switched to the xHCI host controller. The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.
Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!
This patch should be backported to stable kernels as old as 3.0,
that contain commit
69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>