OSDN Git Service
Philippe Mathieu-Daudé [Mon, 26 Jun 2023 14:01:00 +0000 (16:01 +0200)]
target/ppc: Only generate decodetree files when TCG is enabled
No need to generate TCG-specific decodetree files
when TCG is disabled.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <
20230626140100.67941-1-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Nicholas Piggin [Thu, 29 Jun 2023 02:07:13 +0000 (12:07 +1000)]
hw/ppc: Fix clock update drift
The clock update logic reads the clock twice to compute the new clock
value, with a value derived from the later time subtracted from a value
derived from the earlier time. The delta causes time to be lost.
This can ultimately result in time becoming unsynchronized between CPUs
and that can cause OS lockups, timeouts, watchdogs, etc. This can be
seen running a KVM guest (that causes lots of TB updates) on a powernv
SMP machine.
Fix this by reading the clock once.
Cc: qemu-stable@nongnu.org
Fixes:
dbdd25065e90 ("Implement time-base start/stop helpers.")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-ID: <
20230629020713.327745-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Nicholas Piggin [Sun, 25 Jun 2023 12:20:45 +0000 (22:20 +1000)]
target/ppc: Make HDECR underflow edge triggered
HDEC interrupts are edge-triggered on HDECR underflow (notably different
from DEC which is level-triggered).
HDEC interrupts already clear the irq on delivery so that does not need
to be changed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <
20230625122045.15544-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Frederic Barrat [Fri, 30 Jun 2023 10:26:09 +0000 (12:26 +0200)]
pnv/psi: Allow access to PSI registers through xscom
skiboot only uses mmio to access the PSI registers (once the BAR is
set) but we don't have any reason to block the accesses through
xscom. This patch enables xscom access to the PSI registers. It
converts the xscom addresses to mmio addresses, which requires a bit
of care for the PSIHB, then reuse the existing mmio ops.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <
20230630102609.193214-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Richard Henderson [Thu, 6 Jul 2023 17:19:42 +0000 (18:19 +0100)]
Merge tag 'pull-9p-
20230706' of https://github.com/cschoenebeck/qemu into staging
Administrative changes only:
* Deprecate 9p 'proxy' backend.
* Raise status of 9p to 'Maintained'.
# -----BEGIN PGP SIGNATURE-----
#
# iQJLBAABCgA1FiEEltjREM96+AhPiFkBNMK1h2Wkc5UFAmSmkAsXHHFlbXVfb3Nz
# QGNydWRlYnl0ZS5jb20ACgkQNMK1h2Wkc5We1xAAol+HbhQ2zNCJUbZ2/WY3Jf0H
# K86DRQIs6w6UkL9msFz+id+tR5i50HoJ3+RnOKvy/fPqO8Rv6mb0d9r+bIG1JJCc
# ubHP91x/nyDbP0XbLMtmtCz/T4g67E11Qqriq7lH1bPF7ccU3iXHZNup9HARjOoE
# SQo9x4e7IDi1WdmM2vjvRXCh4ZLIlBv7c+2vAeP4V7FhJhDkL+1y+w6aCFw0xpd8
# lto3Egnhz6pk7+SJfQwCl3rfozHhCxlNmcNa+7vqckVFpdJrvtKOQB4cn9yVDPr/
# WjmYoB2J3MwYuZz+qAkdRJ6dUTLJb87YqJJe6lcKq0lqjiFBk7TccvIN9WgyJQd/
# eLUPCCyo98g9RCaPzjLc4MgbpCPCmqJkg8A1vJzykvq51BqJZcdkwfJ7LFmsvTSo
# IfR1Seq4OUUzTZ2gWh8wJBNcPpAbilHzQnumxBEupe0Dg/pwoQWCywTYJN6Yf/6+
# PzcK39bVFKrEyc4Z1Y/yXvAzD7nX8X78kSHvxYYEQfzruLIVQjUUQ7Mp3TiJvljk
# mLdcYqavjawgC2zmZU4L2Lx4Su7iVIkhNWj57WkfooSzLrAjueYQIJEltAt8Qmn6
# x3+u3xI/myNKujMpaqgTAU5Gk2J2UApshq5Zwe8HpnVwWoxS3QetXdA/f4AXwZOk
# TpnKPYQa7edPLSSAbAs=
# =GzjR
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 06 Jul 2023 10:57:31 AM BST
# gpg: using RSA key
96D8D110CF7AF8084F88590134C2B58765A47395
# gpg: issuer "qemu_oss@crudebyte.com"
# gpg: Good signature from "Christian Schoenebeck <qemu_oss@crudebyte.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: ECAB 1A45 4014 1413 BA38 4926 30DB 47C3 A012 D5F4
# Subkey fingerprint: 96D8 D110 CF7A F808 4F88 5901 34C2 B587 65A4 7395
* tag 'pull-9p-
20230706' of https://github.com/cschoenebeck/qemu:
MAINTAINERS: raise status of 9p to 'Maintained'
9pfs: deprecate 'proxy' backend
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson [Thu, 6 Jul 2023 15:19:21 +0000 (16:19 +0100)]
Merge tag 'pull-target-arm-
20230706' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Add raw_writes ops for register whose write induce TLB maintenance
* hw/arm/sbsa-ref: use XHCI to replace EHCI
* Avoid splitting Zregs across lines in dump
* Dump ZA[] when active
* Fix SME full tile indexing
* Handle IC IVAU to improve compatibility with JITs
* xlnx-canfd-test: Fix code coverity issues
* gdbstub: Guard M-profile code with CONFIG_TCG
* allwinner-sramc: Set class_size
* target/xtensa: Assert that interrupt level is within bounds
* Avoid over-length shift in arm_cpu_sve_finalize() error case
* Define new 'neoverse-v1' CPU type
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmSmwEEZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3vBcD/4vKUw6klRV7vyz/KBr2AOi
# Z1FnkLmOhwdp7CKvAVfU58TbPEJ8Fjo7OjziByV5nn/Ht9XrXcdl/E+0JamgrJ/n
# G90ZfpoY3Boan4XBukBz/KX63sT1erF4io1NxbvqLxZ2mbZWNb0D1v2qkxC5zPFE
# 97knlbSle4/VB8N6VgaPaWKVy5gmBZQwl7NUlFtB8TTZp3HPo0V77E9p1Wqpwpls
# BNbqdtgUre3dlJci2f24PmXHYraKa68qk9xGnsSae96EY2+pOHbKhoZ/Fobaor2C
# u+dfgQ3fY3aLDVKx8UESIUoqkGoVqwEbmt+pWG2rJiljLkdsI3ZsVq7p3+VGbLAN
# berL14kCC2vRQYeNUwxeh5wdNVXc58xhWI5KXQRe8hr1dKWS5LQEHWgr7g7mb0+m
# zPHqbdF4FR1DAV29vQ9WyK4zttrinFAYl+zvLyd8dX2ogoUeivR+4o3YX4hlFr4H
# vcrglZbCGqAb3oKQG3PSGliS9GYtBwodLqKEH8PfcwfOP5PIcnSVc0Kl9DSzf7um
# dAuYpaK/XW3MPx5qpWjnip4dRWUV5m/6nSCJr+fELEv3A0sGZY4pywv5NS/Yg1wE
# nXdi8D+nyx9+AAiWTcB+ePsLuDEO2gYtubfqed99TFoJbL6/b4NbH8YE6cF3N/gY
# lqFyvEIYNJZ9klf7XKnX2w==
# =/MkB
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 06 Jul 2023 02:23:13 PM BST
# gpg: using RSA key
E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
* tag 'pull-target-arm-
20230706' of https://git.linaro.org/people/pmaydell/qemu-arm:
target/arm: Avoid over-length shift in arm_cpu_sve_finalize() error case
target/arm: Define neoverse-v1
target/arm: Suppress more TCG unimplemented features in ID registers
target/xtensa: Assert that interrupt level is within bounds
hw: arm: allwinner-sramc: Set class_size
target/arm: gdbstub: Guard M-profile code with CONFIG_TCG
tests/qtest: xlnx-canfd-test: Fix code coverity issues
target/arm: Handle IC IVAU to improve compatibility with JITs
target/arm: Fix SME full tile indexing
target/arm: Dump ZA[] when active
target/arm: Avoid splitting Zregs across lines in dump
tests/tcg/aarch64/sysregs.c: Use S syntax for id_aa64zfr0_el1 and id_aa64smfr0_el1
hw/arm/sbsa-ref: use XHCI to replace EHCI
target/arm: Add raw_writes ops for register whose write induce TLB maintenance
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Peter Maydell [Tue, 4 Jul 2023 15:43:32 +0000 (16:43 +0100)]
target/arm: Avoid over-length shift in arm_cpu_sve_finalize() error case
If you build QEMU with the clang sanitizer enabled, you can see it
fire when running the arm-cpu-features test:
$ QTEST_QEMU_BINARY=./build/arm-clang/qemu-system-aarch64 ./build/arm-clang/tests/qtest/arm-cpu-features
[...]
../../target/arm/cpu64.c:125:19: runtime error: shift exponent 64 is too large for 64-bit type 'unsigned long long'
[...]
This happens because the user can specify some incorrect SVE
properties that result in our calculating a max_vq of 0. We catch
this and error out, but before we do that we calculate
vq_mask = MAKE_64BIT_MASK(0, max_vq);$
and the MAKE_64BIT_MASK() call is only valid for lengths that are
greater than zero, so we hit the undefined behaviour.
Change the logic so that if max_vq is 0 we specifically set vq_mask
to 0 without going via MAKE_64BIT_MASK(). This lets us drop the
max_vq check from the error-exit logic, because if max_vq is 0 then
vq_map must now be 0.
The UB only happens in the case where the user passed us an incorrect
set of SVE properties, so it's not a big problem in practice.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id:
20230704154332.
3014896-1-peter.maydell@linaro.org
Peter Maydell [Tue, 4 Jul 2023 13:06:47 +0000 (14:06 +0100)]
target/arm: Define neoverse-v1
Now that we have implemented support for FEAT_LSE2, we can define
a CPU model for the Neoverse-V1, and enable it for the virt and
sbsa-ref boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id:
20230704130647.
2842917-3-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Peter Maydell [Tue, 4 Jul 2023 13:06:46 +0000 (14:06 +0100)]
target/arm: Suppress more TCG unimplemented features in ID registers
We already squash the ID register field for FEAT_SPE (the Statistical
Profiling Extension) because TCG does not implement it and if we
advertise it to the guest the guest will crash trying to look at
non-existent system registers. Do the same for some other features
which a real hardware Neoverse-V1 implements but which TCG doesn't:
* FEAT_TRF (Self-hosted Trace Extension)
* Trace Macrocell system register access
* Memory mapped trace
* FEAT_AMU (Activity Monitors Extension)
* FEAT_MPAM (Memory Partitioning and Monitoring Extension)
* FEAT_NV (Nested Virtualization)
Most of these, like FEAT_SPE, are "introspection/trace" type features
which QEMU is unlikely to ever implement. The odd-one-out here is
FEAT_NV -- we could implement that and at some point we probably
will.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id:
20230704130647.
2842917-2-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Peter Maydell [Fri, 23 Jun 2023 15:41:35 +0000 (16:41 +0100)]
target/xtensa: Assert that interrupt level is within bounds
In handle_interrupt() we use level as an index into the interrupt_vector[]
array. This is safe because we have checked it against env->config->nlevel,
but Coverity can't see that (and it is only true because each CPU config
sets its XCHAL_NUM_INTLEVELS to something less than MAX_NLEVELS), so it
complains about a possible array overrun (CID
1507131)
Add an assert() which will make Coverity happy and catch the unlikely
case of a mis-set XCHAL_NUM_INTLEVELS in future.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-id:
20230623154135.
1930261-1-peter.maydell@linaro.org
Akihiko Odaki [Wed, 28 Jun 2023 11:09:03 +0000 (20:09 +0900)]
hw: arm: allwinner-sramc: Set class_size
AwSRAMCClass is larger than SysBusDeviceClass so the class size must be
advertised accordingly.
Fixes:
05def917e1 ("hw: arm: allwinner-sramc: Add SRAM Controller support for R40")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id:
20230628110905.38125-1-akihiko.odaki@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fabiano Rosas [Wed, 28 Jun 2023 16:48:21 +0000 (13:48 -0300)]
target/arm: gdbstub: Guard M-profile code with CONFIG_TCG
This code is only relevant when TCG is present in the build. Building
with --disable-tcg --enable-xen on an x86 host we get:
$ ../configure --target-list=x86_64-softmmu,aarch64-softmmu --disable-tcg --enable-xen
$ make -j$(nproc)
...
libqemu-aarch64-softmmu.fa.p/target_arm_gdbstub.c.o: in function `m_sysreg_ptr':
../target/arm/gdbstub.c:358: undefined reference to `arm_v7m_get_sp_ptr'
../target/arm/gdbstub.c:361: undefined reference to `arm_v7m_get_sp_ptr'
libqemu-aarch64-softmmu.fa.p/target_arm_gdbstub.c.o: in function `arm_gdb_get_m_systemreg':
../target/arm/gdbstub.c:405: undefined reference to `arm_v7m_mrs_control'
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Message-id:
20230628164821.16771-1-farosas@suse.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Vikram Garhwal [Wed, 28 Jun 2023 20:27:58 +0000 (13:27 -0700)]
tests/qtest: xlnx-canfd-test: Fix code coverity issues
Following are done to fix the coverity issues:
1. Change read_data to fix the CID
1512899: Out-of-bounds access (OVERRUN)
2. Fix match_rx_tx_data to fix CID
1512900: Logically dead code (DEADCODE)
3. Replace rand() in generate_random_data() with g_rand_int()
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Message-id:
20230628202758.16398-1-vikram.garhwal@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
John Högberg [Tue, 4 Jul 2023 13:08:48 +0000 (14:08 +0100)]
target/arm: Handle IC IVAU to improve compatibility with JITs
Unlike architectures with precise self-modifying code semantics
(e.g. x86) ARM processors do not maintain coherency for instruction
execution and memory, requiring an instruction synchronization
barrier on every core that will execute the new code, and on many
models also the explicit use of cache management instructions.
While this is required to make JITs work on actual hardware, QEMU
has gotten away with not handling this since it does not emulate
caches, and unconditionally invalidates code whenever the softmmu
or the user-mode page protection logic detects that code has been
modified.
Unfortunately the latter does not work in the face of dual-mapped
code (a common W^X workaround), where one page is executable and
the other is writable: user-mode has no way to connect one with the
other as that is only known to the kernel and the emulated
application.
This commit works around the issue by telling software that
instruction cache invalidation is required by clearing the
CPR_EL0.DIC flag (regardless of whether the emulated processor
needs it), and then invalidating code in IC IVAU instructions.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1034
Co-authored-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: John Högberg <john.hogberg@ericsson.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id:
168778890374.24232.
3402138851538068785-1@git.sr.ht
[PMM: removed unnecessary AArch64 feature check; moved
"clear CTR_EL1.DIC" code up a bit so it's not in the middle
of the vfp/neon related tests]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Richard Henderson [Tue, 4 Jul 2023 13:08:48 +0000 (14:08 +0100)]
target/arm: Fix SME full tile indexing
For the outer product set of insns, which take an entire matrix
tile as output, the argument is not a combined tile+column.
Therefore using get_tile_rowcol was incorrect, as we extracted
the tile number from itself.
The test case relies only on assembler support for SME, since
no release of GCC recognizes -march=armv9-a+sme yet.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1620
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id:
20230622151201.
1578522-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: dropped now-unneeded changes to sysregs CFLAGS]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Richard Henderson [Tue, 4 Jul 2023 13:08:48 +0000 (14:08 +0100)]
target/arm: Dump ZA[] when active
Always print each matrix row whole, one per line, so that we
get the entire matrix in the proper shape.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id:
20230622151201.
1578522-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Richard Henderson [Tue, 4 Jul 2023 13:08:47 +0000 (14:08 +0100)]
target/arm: Avoid splitting Zregs across lines in dump
Allow the line length to extend to 548 columns. While annoyingly wide,
it's still less confusing than the continuations we print. Also, the
default VL used by Linux (and max for A64FX) uses only 140 columns.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id:
20230622151201.
1578522-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Thu, 6 Jul 2023 11:38:19 +0000 (12:38 +0100)]
tests/tcg/aarch64/sysregs.c: Use S syntax for id_aa64zfr0_el1 and id_aa64smfr0_el1
Some assemblers will complain about attempts to access
id_aa64zfr0_el1 and id_aa64smfr0_el1 by name if the test
binary isn't built for the right processor type:
/tmp/ccASXpLo.s:782: Error: selected processor does not support system register name 'id_aa64zfr0_el1'
/tmp/ccASXpLo.s:829: Error: selected processor does not support system register name 'id_aa64smfr0_el1'
However, these registers are in the ID space and are guaranteed to
read-as-zero on older CPUs, so the access is both safe and sensible.
Switch to using the S syntax, as we already do for ID_AA64ISAR2_EL1
and ID_AA64MMFR2_EL1. This allows us to drop the HAS_ARMV9_SME check
and the makefile machinery to adjust the CFLAGS for this test, so we
don't rely on having a sufficiently new compiler to be able to check
these registers.
This means we're actually testing the SME ID register: no released
GCC yet recognizes -march=armv9-a+sme, so that was always skipped.
It also avoids a future problem if we try to switch the "do we have
SME support in the toolchain" check from "in the compiler" to "in the
assembler" (at which point we would otherwise run into the above
errors).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Christian Schoenebeck [Mon, 3 Jul 2023 14:34:17 +0000 (16:34 +0200)]
MAINTAINERS: raise status of 9p to 'Maintained'
Change status of 9p from 'Odd Fixes' to 'Maintained', as this better
reflects current situation. I already take care of 9p patches for a
while, which included new features as well.
Based-on: <E1qDkmw-0007M1-8f@lizzy.crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <E1qGKgV-0003Hj-01@lizzy.crudebyte.com>
Christian Schoenebeck [Mon, 26 Jun 2023 11:49:06 +0000 (13:49 +0200)]
9pfs: deprecate 'proxy' backend
As recent CVE-2023-2861 (fixed by
f6b0de53fb) once again showed, the 9p
'proxy' fs driver is in bad shape. Using the 'proxy' backend was already
discouraged for safety reasons before and we recommended to use the
'local' backend (preferably in conjunction with its 'mapped' security
model) instead, but now it is time to officially deprecate the 'proxy'
backend.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <E1qDkmw-0007M1-8f@lizzy.crudebyte.com>
Richard Henderson [Tue, 4 Jul 2023 16:40:13 +0000 (18:40 +0200)]
Merge tag 'block-pull-request' of https://gitlab.com/stefanha/qemu into staging
Pull request
Fix --enable-modules with the blkio block driver.
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEhpWov9P5fNqsNXdanKSrs4Grc8gFAmSkOtQACgkQnKSrs4Gr
# c8ipnQgAqrcwgJliN9wMopm5bFEiHkAppvGz/+qliEpQI5X7xt+YGhcEx7O7ZNMu
# uSz47y5uQwNNbh4HA51gUkSopAcfH2FP8rD/FH5x7D7mmR3M61AH5LEzzlBbnneW
# ZtuGSNIvV23mTlQOHqNOGQxV9k3QGrXfxQz0Hy4NKP6jiC1zNdAsCXC8dj9Fda+M
# nobFXe21qhm0YHYGVgLurbjlTY3aBxL3SOSG550OjQT1Prpi+rw26aK0Gtg1jWL/
# ynGEgxgUjvO2uqZk71NN5Xr6CLe/SLO9cdIeuhwXffna5uf80S254fMhr9Yr1h52
# P5UFi4iQZi//fprGD72a6eyogdSzUg==
# =USrv
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 04 Jul 2023 05:29:24 PM CEST
# gpg: using RSA key
8695A8BFD3F97CDAAC35775A9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
* tag 'block-pull-request' of https://gitlab.com/stefanha/qemu:
block/blkio: fix module_block.py parsing
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Stefan Hajnoczi [Tue, 4 Jul 2023 12:34:36 +0000 (14:34 +0200)]
block/blkio: fix module_block.py parsing
When QEMU is built with --enable-modules, the module_block.py script
parses block/*.c to find block drivers that are built as modules. The
script generates a table of block drivers called block_driver_modules[].
This table is used for block driver module loading.
The blkio.c driver uses macros to define its BlockDriver structs. This
was done to avoid code duplication but the module_block.py script is
unable to parse the macro. The result is that libblkio-based block
drivers can be built as modules but will not be found at runtime.
One fix is to make the module_block.py script or build system fancier so
it can parse C macros (e.g. by parsing the preprocessed source code). I
chose not to do this because it raises the complexity of the build,
making future issues harder to debug.
Keep things simple: use the macro to avoid duplicating BlockDriver
function pointers but define .format_name and .protocol_name manually
for each BlockDriver. This way the module_block.py is able to parse the
code.
Also get rid of the block driver name macros (e.g. DRIVER_IO_URING)
because module_block.py cannot parse them either.
Fixes:
fd66dbd424f5 ("blkio: add libblkio block driver")
Reported-by: Qing Wang <qinwang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id:
20230704123436.187761-1-stefanha@redhat.com
Cc: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Yuquan Wang [Tue, 4 Jul 2023 13:08:47 +0000 (14:08 +0100)]
hw/arm/sbsa-ref: use XHCI to replace EHCI
The current sbsa-ref cannot use EHCI controller which is only
able to do 32-bit DMA, since sbsa-ref doesn't have RAM below 4GB.
Hence, this uses XHCI to provide a usb controller with 64-bit
DMA capablity instead of EHCI.
We bump the platform version to 0.3 with this change. Although the
hardware at the USB controller address changes, the firmware and
Linux can both cope with this -- on an older non-XHCI-aware
firmware/kernel setup the probe routine simply fails and the guest
proceeds without any USB. (This isn't a loss of functionality,
because the old USB controller never worked in the first place.) So
we can call this a backwards-compatible change and only bump the
minor version.
Signed-off-by: Yuquan Wang <wangyuquan1236@phytium.com.cn>
Message-id:
20230621103847.447508-2-wangyuquan1236@phytium.com.cn
[PMM: tweaked commit message; add line to docs about what
changes in platform version 0.3]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Eric Auger [Tue, 4 Jul 2023 13:08:47 +0000 (14:08 +0100)]
target/arm: Add raw_writes ops for register whose write induce TLB maintenance
Some registers whose 'cooked' writefns induce TLB maintenance do
not have raw_writefn ops defined. If only the writefn ops is set
(ie. no raw_writefn is provided), it is assumed the cooked also
work as the raw one. For those registers it is not obvious the
tlb_flush works on KVM mode so better/safer setting the raw write.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Richard Henderson [Tue, 4 Jul 2023 06:36:44 +0000 (08:36 +0200)]
Merge tag 'pull-maintainer-ominbus-030723-1' of https://gitlab.com/stsquad/qemu into staging
maintainer updates: testing, fuzz, plugins, docs, gdbstub
- clean up gitlab artefact handling
- ensure gitlab publishes artefacts with coverage data
- reduce testing scope for coverage job
- mention CI pipeline in developer docs
- add ability to add plugin args to check-tcg
- fix some memory leaks and UB in tests
- suppress xcb leaks from fuzzing output
- add a test-fuzz to mirror the CI run
- allow lci-refresh to be run in $SRC
- update lcitool to latest version
- add qemu-minimal package set with gcc-native
- convert riscv64-cross to lcitool
- update sbsa-ref tests
- don't include arm_casq_ptw emulation unless TCG
- convert plugins to use g_memdup2
- ensure plugins instrument SVE helper mem access
- improve documentation of QOM/QDEV
- make gdbstub send stop responses when it should
- report user-mode pid in gdbstub
- add support for info proc mappings in gdbstub
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmSiuH4ACgkQ+9DbCVqe
# KkRt0Qf+N0oD/VuEcRSxK1bWlLtf5nxQpPKKzkRItPc5jqJnLWa/gh21sfQgs5Uq
# BczAT+JfgTnMozbq0mjvQ+uAGI4MHzBs+UAn60+ZcXfk2inyk77XKBEoHOFuK1ry
# rgQ4+p21/hcZedDiDLnLSfbGfUU0KkM/pbAegOz7HO0EQDV0CSXqeAW3WAuM1lne
# +YmXkKwoFI1V8HvslzCT12GFiaUfmSSBtASqWcf67Ief97K24+rpkAVM7JChLm5X
# fC1MOFNuNYV+jO+9U3KIs15P1WH12oMcpNUY+KqQ5ZWovBg83yOLtKY1o3f6Z2Y+
# iQgFJr6F8ZVBdKNJtqVi8DkbiFfbsA==
# =Ho/h
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 03 Jul 2023 02:01:02 PM CEST
# gpg: using RSA key
6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* tag 'pull-maintainer-ominbus-030723-1' of https://gitlab.com/stsquad/qemu: (38 commits)
tests/tcg: Add a test for info proc mappings
docs: Document security implications of debugging
gdbstub: Add support for info proc mappings
gdbstub: Report the actual qemu-user pid
gdbstub: Expose gdb_get_process() and gdb_get_first_cpu_in_process()
linux-user: Emulate /proc/self/smaps
linux-user: Add "safe" parameter to do_guest_openat()
linux-user: Expose do_guest_openat() and do_guest_readlink()
gdbstub: clean-up vcont handling to avoid goto
gdbstub: Permit reverse step/break to provide stop response
gdbstub: lightly refactor connection to avoid snprintf
docs/devel: introduce some key concepts for QOM development
docs/devel: split qom-api reference into new file
docs/devel/qom.rst: Correct code style
include/hw/qdev-core: fixup kerneldoc annotations
include/migration: mark vmstate_register() as a legacy function
docs/devel: add some front matter to the devel index
plugins: update lockstep to use g_memdup2
plugins: fix memory leak while parsing options
plugins: force slow path when plugins instrument memory ops
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:23 +0000 (19:04 +0100)]
tests/tcg: Add a test for info proc mappings
Add a small test to prevent regressions.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <
20230621203627.
1808446-9-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-39-alex.bennee@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:22 +0000 (19:04 +0100)]
docs: Document security implications of debugging
Now that the GDB stub explicitly implements reading host files (note
that it was already possible by changing the emulated code to open and
read those files), concerns may arise that it undermines security.
Document the status quo, which is that the users are already
responsible for securing the GDB connection themselves.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <
20230621203627.
1808446-8-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-38-alex.bennee@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:21 +0000 (19:04 +0100)]
gdbstub: Add support for info proc mappings
Currently the GDB's generate-core-file command doesn't work well with
qemu-user: the resulting dumps are huge [1] and at the same time
incomplete (argv and envp are missing). The reason is that GDB has no
access to proc mappings and therefore has to fall back to using
heuristics for discovering them. This is, in turn, because qemu-user
does not implement the Host I/O feature of the GDB Remote Serial
Protocol.
Implement vFile:{open,close,pread,readlink} and also
qXfer:exec-file:read+. With that, generate-core-file begins to work on
aarch64 and s390x.
[1] https://sourceware.org/pipermail/gdb-patches/2023-May/199432.html
Co-developed-by: Dominik 'Disconnect3d' Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <
20230621203627.
1808446-7-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-37-alex.bennee@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:20 +0000 (19:04 +0100)]
gdbstub: Report the actual qemu-user pid
Currently qemu-user reports pid 1 to GDB. Resolve the TODO and report
the actual PID. Using getpid() relies on the assumption that there is
only one GDBProcess. Add an assertion to make sure that future changes
don't break it.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <
20230621203627.
1808446-6-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-36-alex.bennee@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:19 +0000 (19:04 +0100)]
gdbstub: Expose gdb_get_process() and gdb_get_first_cpu_in_process()
These functions will be needed by user-target.c in order to retrieve
the name of the executable.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <
20230621203627.
1808446-5-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-35-alex.bennee@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:18 +0000 (19:04 +0100)]
linux-user: Emulate /proc/self/smaps
/proc/self/smaps is an extension of /proc/self/maps: it provides the
same lines, plus additional information about each range.
GDB uses /proc/self/smaps when available, which means that
generate-core-file tries it first before falling back to
/proc/self/maps. This, in turn, causes it to dump the host mappings,
since /proc/self/smaps is not emulated and is just passed through.
Fix by emulating /proc/self/smaps. Provide true values only for
Size, KernelPageSize, MMUPageSize and VmFlags. Leave all other values
at 0, which is a valid conservative estimate.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <
20230621203627.
1808446-4-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-34-alex.bennee@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:17 +0000 (19:04 +0100)]
linux-user: Add "safe" parameter to do_guest_openat()
gdbstub cannot meaningfully handle QEMU_ERESTARTSYS, and it doesn't
need to. Add a parameter to do_guest_openat() that makes it use
openat() instead of safe_openat(), so that it becomes usable from
gdbstub.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <
20230621203627.
1808446-3-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-33-alex.bennee@linaro.org>
Ilya Leoshkevich [Fri, 30 Jun 2023 18:04:16 +0000 (19:04 +0100)]
linux-user: Expose do_guest_openat() and do_guest_readlink()
These functions will be required by the GDB stub in order to provide
the guest view of /proc to GDB.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <
20230621203627.
1808446-2-iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-32-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:15 +0000 (19:04 +0100)]
gdbstub: clean-up vcont handling to avoid goto
We can handle all the error exit cases by using g_autofree() for the
one thing that needs cleaning up on the exit.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-31-alex.bennee@linaro.org>
Nicholas Piggin [Fri, 30 Jun 2023 18:04:14 +0000 (19:04 +0100)]
gdbstub: Permit reverse step/break to provide stop response
The final part of the reverse step and break handling is to bring
the machine back to a debug stop state. gdb expects a response.
A gdb 'rsi' command hangs forever because the gdbstub filters out
the response (also observable with reverse_debugging.py avocado
tests).
Fix by setting allow_stop_reply for the gdb backward packets.
Fixes:
758370052fb ("gdbstub: only send stop-reply packets when allowed to")
Cc: qemu-stable@nongnu.org
Cc: Matheus Tavares Bernardino <quic_mathbern@quicinc.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Taylor Simpson <tsimpson@quicinc.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Matheus Tavares Bernardino <quic_mathbern@quicinc.com>
Message-Id: <
20230623035304.279833-1-npiggin@gmail.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-30-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:13 +0000 (19:04 +0100)]
gdbstub: lightly refactor connection to avoid snprintf
This may be a bit too much to avoid an snprintf and the slightly dodgy
assign to a const variable. But hopefully not.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-29-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:12 +0000 (19:04 +0100)]
docs/devel: introduce some key concepts for QOM development
Using QOM correctly is increasingly important to maintaining a modern
code base. However the current documentation skips some important
concepts before launching into a simple example. Lets:
- at least mention properties
- mention TYPE_OBJECT and TYPE_DEVICE
- talk about why we have realize/unrealize
- mention the QOM tree
- lightly re-arrange the order we mention things
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-28-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:11 +0000 (19:04 +0100)]
docs/devel: split qom-api reference into new file
Lets try and keep the overview of the sub-system digestible by
splitting the core API stuff into a separate file. As QOM and QDEV
work together we should also try and enumerate the qdev_ functions.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-27-alex.bennee@linaro.org>
Philippe Mathieu-Daudé [Fri, 30 Jun 2023 18:04:10 +0000 (19:04 +0100)]
docs/devel/qom.rst: Correct code style
Per commit
067109a11c ("docs/devel: mention the spacing requirement
for QOM"):
For a storage structure the first declaration should always be
called “parent_obj” and for a class structure the first member
should always be called “parent_class”
Adapt the QOM rST document accordingly.
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <
20230622101717.70468-1-philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-26-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:09 +0000 (19:04 +0100)]
include/hw/qdev-core: fixup kerneldoc annotations
Fix up the kerneldoc markup and start documenting the various fields
in QDEV related structures. This involved:
- moving overall description to a DOC: comment at top
- fixing various markup issues for types and structures
- adding missing Return: statements
- adding some typedefs to hide QLIST macros in headers
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-25-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:08 +0000 (19:04 +0100)]
include/migration: mark vmstate_register() as a legacy function
Mention that QOM-ified devices already have support for registering
the description.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-24-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:07 +0000 (19:04 +0100)]
docs/devel: add some front matter to the devel index
Give an overview of the most useful bits of the devel documentation to
read depending on what the developer wants to do.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-23-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:06 +0000 (19:04 +0100)]
plugins: update lockstep to use g_memdup2
The old g_memdup is deprecated, use the replacement.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-22-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:05 +0000 (19:04 +0100)]
plugins: fix memory leak while parsing options
It was hard to track down this leak as it was an internal allocation
by glib and the backtraces did not give much away. The autofree was
freeing the allocation with g_free() but not taking care of the
individual strings. They should have been freed with g_strfreev()
instead.
Searching the glib source code for the correct string free function
led to:
G_DEFINE_AUTO_CLEANUP_FREE_FUNC(GStrv, g_strfreev, NULL)
and indeed if you read to the bottom of the documentation page you
will find:
typedef gchar** GStrv;
A typedef alias for gchar**. This is mostly useful when used together with g_auto().
So fix up all the g_autofree g_strsplit case that smugly thought they
had de-allocation covered.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-21-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:04 +0000 (19:04 +0100)]
plugins: force slow path when plugins instrument memory ops
The lack of SVE memory instrumentation has been an omission in plugin
handling since it was introduced. Fortunately we can utilise the
probe_* functions to force all all memory access to follow the slow
path. We do this by checking the access type and presence of plugin
memory callbacks and if set return the TLB_MMIO flag.
We have to jump through a few hoops in user mode to re-use the flag
but it was the desired effect:
./qemu-system-aarch64 -display none -serial mon:stdio \
-M virt -cpu max -semihosting-config enable=on \
-kernel ./tests/tcg/aarch64-softmmu/memory-sve \
-plugin ./contrib/plugins/libexeclog.so,ifilter=st1w,afilter=0x40001808 -d plugin
gives (disas doesn't currently understand st1w):
0, 0x40001808, 0xe54342a0, ".byte 0xa0, 0x42, 0x43, 0xe5", store, 0x40213010, RAM, store, 0x40213014, RAM, store, 0x40213018, RAM
And for user-mode:
./qemu-aarch64 \
-plugin contrib/plugins/libexeclog.so,afilter=0x4007c0 \
-d plugin \
./tests/tcg/aarch64-linux-user/sha512-sve
gives:
1..10
ok 1 - do_test(&tests[i])
0, 0x4007c0, 0xa4004b80, ".byte 0x80, 0x4b, 0x00, 0xa4", load, 0x5500800370, load, 0x5500800371, load, 0x5500800372, load, 0x5500800373, load, 0x5500800374, load, 0x5500800375, load, 0x5500800376, load, 0x5500800377, load, 0x5500800378, load, 0x5500800379, load, 0x550080037a, load, 0x550080037b, load, 0x550080037c, load, 0x550080037d, load, 0x550080037e, load, 0x550080037f, load, 0x5500800380, load, 0x5500800381, load, 0x5500800382, load, 0x5500800383, load, 0x5500800384, load, 0x5500800385, load, 0x5500800386, lo
ad, 0x5500800387, load, 0x5500800388, load, 0x5500800389, load, 0x550080038a, load, 0x550080038b, load, 0x550080038c, load, 0x550080038d, load, 0x550080038e, load, 0x550080038f, load, 0x5500800390, load, 0x5500800391, load, 0x5500800392, load, 0x5500800393, load, 0x5500800394, load, 0x5500800395, load, 0x5500800396, load, 0x5500800397, load, 0x5500800398, load, 0x5500800399, load, 0x550080039a, load, 0x550080039b, load, 0x550080039c, load, 0x550080039d, load, 0x550080039e, load, 0x550080039f, load, 0x55008003a0, load, 0x55008003a1, load, 0x55008003a2, load, 0x55008003a3, load, 0x55008003a4, load, 0x55008003a5, load, 0x55008003a6, load, 0x55008003a7, load, 0x55008003a8, load, 0x55008003a9, load, 0x55008003aa, load, 0x55008003ab, load, 0x55008003ac, load, 0x55008003ad, load, 0x55008003ae, load, 0x55008003af
(4007c0 is the ld1b in the sha512-sve)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Robert Henry <robhenry@microsoft.com>
Cc: Aaron Lindsay <aaron@os.amperecomputing.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-20-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:03 +0000 (19:04 +0100)]
target/arm: make arm_casq_ptw CONFIG_TCG only
The ptw code is accessed by non-TCG code (specifically arm_pamax and
arm_cpu_get_phys_page_attrs_debug) but most of it is really only for
TCG emulation. Seeing as we already assert for a non TARGET_AARCH64
build lets extend the test rather than further messing with the ifdef
ladder.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-19-alex.bennee@linaro.org>
Thomas Huth [Fri, 30 Jun 2023 18:04:02 +0000 (19:04 +0100)]
tests/avocado: Make the test_arm_bpim2u_gmac test more reliable
The test_arm_bpim2u_gmac test sometimes fails (ca. 1 out of 20 runs
here) since the disk shows up as /dev/mmcblk1 instead of /dev/mmcblk0
in some runs. No matter of the name in /dev, the major:minor encoding
seems always to be the same, so we can fix this issue by using the
correct major:minor hex number in the "root=" parameter instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <
20230630161604.446394-1-thuth@redhat.com>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-18-alex.bennee@linaro.org>
Marcin Juszkiewicz [Fri, 30 Jun 2023 18:04:01 +0000 (19:04 +0100)]
tests/avocado: update firmware to enable sbsa-ref/max
Update prebuilt firmware images to have TF-A with FEAT_FGT support
enabled. This allowed us to enable test for "max" cpu in sbsa-ref
machine.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-Id: <
20230530152240.79160-1-marcin.juszkiewicz@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-17-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:04:00 +0000 (19:04 +0100)]
tests/docker: convert riscv64-cross to lcitool
We still need to base this on Debian Sid until riscv64 is promoted to
a release architecture (or another distro provides a full cross
compile target). We use the new qemu-minimal project description to
avoid bringing in all the extra dependencies because every extra
package is another chance for sid to fail.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-16-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:59 +0000 (19:03 +0100)]
tests/lcitool: introduce qemu-minimal
This is a very bare bones set of dependencies for a minimal build of
QEMU. This will be useful for minimal cross-compile sanity check based
on things like Debian Sid where stuff isn't always in sync.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-15-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:58 +0000 (19:03 +0100)]
tests/lcitool: add an explicit gcc-native package
We need a native compiler to build the hexagon codegen tools. In our
current images we already have a gcc as a side effect of a broken
dependency between gcovr and lcov but this will be fixed when we move
to bookworm. See
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=987818 for details.
Update the packages while we are at it.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-14-alex.bennee@linaro.org>
Erik Skultety [Fri, 30 Jun 2023 18:03:57 +0000 (19:03 +0100)]
tests/lcitool: Bump fedora container versions
Fedora 37 -> 38
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <
c9b00e573a7a80fc6ce5c68595382f5c916a9195.
1685528076.git.eskultet@redhat.com>
[AJB: Dropped alpine (in prev commit), reflow commit msg]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-13-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:56 +0000 (19:03 +0100)]
tests/lcitool: update to latest version
We need this for the riscv64 and gcc-native mappings. As the older
alpine release has been dropped from the mappings we also need to bump
the version of alpine we use.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-12-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:55 +0000 (19:03 +0100)]
Makefile: add lcitool-refresh to UNCHECKED_GOALS
This is yet another make target you usually run in the top level of
the source directory.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-11-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:54 +0000 (19:03 +0100)]
tests/docker: add test-fuzz
Running the fuzzer requires some hoop jumping and some problems only
show up in containers. This basically replicates the build-oss-fuzz
job from our CI so we can run in the same containers we use in CI.
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-10-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:53 +0000 (19:03 +0100)]
tests/qtests: clean-up and fix leak in generic_fuzz
An update to the clang tooling detects more issues with the code
including a memory leak from the g_string_new() allocation. Clean up
the code to avoid the allocation and use ARRAY_SIZE while we are at
it.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-9-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:52 +0000 (19:03 +0100)]
scripts/oss-fuzz: add a suppression for keymap
When updating to the latest fedora the santizer found more leaks
inside xkbmap:
FAILED: pc-bios/keymaps/ar
/builds/stsquad/qemu/build-oss-fuzz/qemu-keymap -f pc-bios/keymaps/ar -l ara
=================================================================
==3604==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 1424 byte(s) in 1 object(s) allocated from:
#0 0x56316418ebec in __interceptor_calloc (/builds/stsquad/qemu/build-oss-fuzz/qemu-keymap+0x127bec) (BuildId:
a2ad9da3190962acaa010fa8f44a9269f9081e1c)
#1 0x7f60d4dc067e (/lib64/libxkbcommon.so.0+0x1c67e) (BuildId:
b243a34e4e58e6a30b93771c256268b114d34b80)
#2 0x7f60d4dc2137 in xkb_keymap_new_from_names (/lib64/libxkbcommon.so.0+0x1e137) (BuildId:
b243a34e4e58e6a30b93771c256268b114d34b80)
#3 0x5631641ca50f in main /builds/stsquad/qemu/build-oss-fuzz/../qemu-keymap.c:215:11
and many more. As we can't do anything about the library add a
suppression to keep the CI going with what its meant to be doing.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-8-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:51 +0000 (19:03 +0100)]
qemu-keymap: properly check return from xkb_keymap_mod_get_index
We can return XKB_MOD_INVALID for AltGr which rightly gets flagged by
sanitisers as an overly wide shift attempt. Properly check the return
type and leave the bitmap as zero in that case. Tested output before
and after is unchanged with the gb and ara keymaps.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-7-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:50 +0000 (19:03 +0100)]
tests/tcg: add mechanism to handle plugin arguments
We recently missed a regression that should have been picked up by
check-tcg. This was because the libmem plugin is effectively a NOP if
the user doesn't specify the type to use.
Rather than changing the default behaviour add an additional expansion
so we can take this into account in future.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-6-alex.bennee@linaro.org>
Ani Sinha [Fri, 30 Jun 2023 18:03:49 +0000 (19:03 +0100)]
docs/devel: remind developers to run CI container pipeline when updating images
When new dependencies and packages are added to containers, its important to
run CI container generation pipelines on gitlab to make sure that there are no
obvious conflicts between packages that are being added and those that are
already present. Running CI container pipelines will make sure that there are
no such breakages before we commit the change updating the containers. Add a
line in the documentation reminding developers to run the pipeline before
submitting the change. It will also ease the life of the maintainers.
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <
20230506072012.10350-1-anisinha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-5-alex.bennee@linaro.org>
Alex Bennée [Fri, 30 Jun 2023 18:03:48 +0000 (19:03 +0100)]
gitlab: reduce testing scope of check-gcov
This keeps timing out on gitlab due to some qtests taking a long time.
As this is just ensuring the gcov machinery is working and not
attempting to be comprehensive lets skip qtest in this run.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-4-alex.bennee@linaro.org>
Daniel P. Berrangé [Fri, 30 Jun 2023 18:03:47 +0000 (19:03 +0100)]
gitlab: ensure coverage job also publishes meson log
The coverage job wants to publish a coverage report on success, but the
tests might fail and in that case we need the meson logs for debugging.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <
20230503145535.91325-3-berrange@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-3-alex.bennee@linaro.org>
Daniel P. Berrangé [Fri, 30 Jun 2023 18:03:46 +0000 (19:03 +0100)]
gitlab: explicit set artifacts publishing criteria
If not set explicitly, gitlab assumes 'when: on_success" as the
publishing criteria for artifacts. This is reasonable if the
artifact is an output deliverable of the job. This is useless
if the artifact is a log file to be used for debugging job
failures.
This change makes the desired criteria explicit for every job
that publishes artifacts.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <
20230503145535.91325-2-berrange@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230630180423.558337-2-alex.bennee@linaro.org>
Richard Henderson [Sat, 1 Jul 2023 06:55:37 +0000 (08:55 +0200)]
Merge tag 'pull-tcg-
20230701' of https://gitlab.com/rth7680/qemu into staging
dbus: Two hot fixes, per request of Marc-André Lureau
accel/tcg: Fix tb_invalidate_phys_range iteration
fpu: Add float64_to_int{32,64}_modulo
tcg: Reduce scope of tcg_assert_listed_vecop
target/nios2: Explicitly ask for target-endian loads
linux-user: Avoid mmap of the last byte of the reserved_va
# -----BEGIN PGP SIGNATURE-----
#
# iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmSfzXwdHHJpY2hhcmQu
# aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV+GMAgAicMA7dZEUNiKT1co
# pwQNF/aQehs3a+UYcHFZRQWjwNsXzDrPRTAyBkDFrzR2ILxKlpPw2JBRiqrr9pqj
# YWit0pHVv/OAYfSEzcqUaIeWyAh2xlAT4IbSz+sLcPBdPgUwm3z0Y7mTz3kUAkB2
# gXO/iuoD8ORwgSnFvH+FSws16kr1x/8cAaObY7BupUhS7hK8M9zsCehhk6ssxv7+
# EpR0kDIeoC2kjJLvQAoGW4DPzfmAvVmI/OiJKpqrAlTJIeAkngalSuaxj/t9Dte6
# zy4h8JW5VbHw3qLxTvg42/Pk4AiweBh38hpUfLQ2cprO7dy+T9qS2v8CGnMzrmeB
# kzlIMg==
# =a7vA
# -----END PGP SIGNATURE-----
# gpg: Signature made Sat 01 Jul 2023 08:53:48 AM CEST
# gpg: using RSA key
7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [ultimate]
* tag 'pull-tcg-
20230701' of https://gitlab.com/rth7680/qemu:
linux-user: Avoid mmap of the last byte of the reserved_va
target/nios2 : Explicitly ask for target-endian loads and stores
tcg: Reduce tcg_assert_listed_vecop() scope
target/arm: Use float64_to_int32_modulo for FJCVTZS
target/alpha: Use float64_to_int64_modulo for CVTTQ
tests/tcg/alpha: Add test for cvttq
fpu: Add float64_to_int{32,64}_modulo
accel/tcg: Assert one page in tb_invalidate_phys_page_range__locked
accel/tcg: Fix start page passed to tb_invalidate_phys_page_range__locked
audio: dbus requires pixman
ui/dbus: fix build errors in dbus_update_gl_cb and dbus_call_update_gl
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson [Thu, 29 Jun 2023 08:08:35 +0000 (10:08 +0200)]
linux-user: Avoid mmap of the last byte of the reserved_va
There is an overflow problem in mmap_find_vma_reserved:
when reserved_va == UINT32_MAX, end may overflow to 0.
Rather than a larger rewrite at this time, simply avoid
the final byte of the VA, which avoids searching the
final page, which avoids the overflow.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1741
Fixes:
95059f9c ("include/exec: Change reserved_va semantics to last byte")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-Id: <
20230629080835.71371-1-richard.henderson@linaro.org>
Peter Maydell [Fri, 23 Jun 2023 17:25:56 +0000 (18:25 +0100)]
target/nios2 : Explicitly ask for target-endian loads and stores
When we generate code for guest loads and stores, at the moment they
end up being requests for a host-endian access. So for target-system-nios2
(little endian) a load like
ldw r3,0(r4)
results on an x86 host in the TCG IR
qemu_ld_a32_i32 r3,loc2,al+leul,0
but on s390 it is
qemu_ld_a32_i32 r3,loc2,al+beul,0
The result is that guests don't work on big-endian hosts.
Use the MO_TE* memops rather than the plain ones.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1693
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <
20230623172556.
1951974-1-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Philippe Mathieu-Daudé [Thu, 29 Jun 2023 09:11:07 +0000 (11:11 +0200)]
tcg: Reduce tcg_assert_listed_vecop() scope
tcg_assert_listed_vecop() is only used in tcg-op-vec.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <
20230629091107.74384-1-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson [Sat, 27 May 2023 14:19:10 +0000 (07:19 -0700)]
target/arm: Use float64_to_int32_modulo for FJCVTZS
The standard floating point results are provided by the generic routine.
We only need handle the extra Z flag result afterward.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230527141910.
1885950-5-richard.henderson@linaro.org>
Richard Henderson [Sat, 27 May 2023 14:19:09 +0000 (07:19 -0700)]
target/alpha: Use float64_to_int64_modulo for CVTTQ
For the most part we can use the new generic routine,
though exceptions need some post-processing to sort
invalid from integer overflow.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <
20230527141910.
1885950-4-richard.henderson@linaro.org>
Richard Henderson [Sat, 27 May 2023 14:19:08 +0000 (07:19 -0700)]
tests/tcg/alpha: Add test for cvttq
Test for invalid, integer overflow, and inexact.
Test for proper result, modulo 2**64.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230527141910.
1885950-3-richard.henderson@linaro.org>
Richard Henderson [Sat, 27 May 2023 14:19:07 +0000 (07:19 -0700)]
fpu: Add float64_to_int{32,64}_modulo
Add versions of float64_to_int* which do not saturate the result.
Reviewed-by: Christoph Muellner <christoph.muellner@vrull.eu>
Tested-by: Christoph Muellner <christoph.muellner@vrull.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <
20230527141910.
1885950-2-richard.henderson@linaro.org>
Mark Cave-Ayland [Thu, 29 Jun 2023 08:25:22 +0000 (09:25 +0100)]
accel/tcg: Assert one page in tb_invalidate_phys_page_range__locked
Ensure that that both the start and last addresses are within
the same guest page.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <
20230629082522.606219-3-mark.cave-ayland@ilande.co.uk>
[rth: Use tcg_debug_assert, simplify the expression]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Mark Cave-Ayland [Thu, 29 Jun 2023 08:25:21 +0000 (09:25 +0100)]
accel/tcg: Fix start page passed to tb_invalidate_phys_page_range__locked
Due to a copy-paste error in tb_invalidate_phys_range, the wrong
start address was passed to tb_invalidate_phys_page_range__locked.
Correct is to use the start of each page in turn.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes:
e506ad6a05 ("accel/tcg: Pass last not end to tb_invalidate_phys_range")
Message-Id: <
20230629082522.606219-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Marc-André Lureau [Fri, 30 Jun 2023 21:41:56 +0000 (23:41 +0200)]
audio: dbus requires pixman
Commit commit
6cc5a615 ("ui/dbus: win32 support") has broken audio/dbus
compilation when pixman is not included.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1739
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <
20230630214156.
2181558-1-marcandre.lureau@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson [Fri, 30 Jun 2023 17:38:06 +0000 (19:38 +0200)]
ui/dbus: fix build errors in dbus_update_gl_cb and dbus_call_update_gl
Add some ifdefs to avoid an unused function and unused variable.
Fixes:
de1f8ce0abb8 ("ui/dbus: use shared D3D11 Texture2D when possible")
Co-developed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <
336f7697-bcfa-1f5f-e411-
6859815aa26c@eik.bme.hu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson [Fri, 30 Jun 2023 06:11:08 +0000 (08:11 +0200)]
Merge tag 'pull-vfio-
20230630' of https://github.com/legoater/qemu into staging
vfio queue:
* migration: New switchover ack to reduce downtime
* VFIO migration pre-copy support
* Removal of the VFIO migration experimental flag
* Alternate offset for GPUDirect Cliques
* Misc fixes
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmSeVHYACgkQUaNDx8/7
# 7KHeZw/+LRe9QQpx8hU//vKBvLet2QvI3WUaXGHiHbblbRT6HhiHjWHB2/8j6jji
# QhAGJ6w9yoKODyY0kGpVFEnkmXOKyqwWssBheV219ntZs09pFGxZr/ldUhT22aBN
# kH8mHU9BZ3J+zF/kKphpcIC1sPxVu/DlrtnJu5vDGuRAOu8+3kFV217JC1yGs1Vh
# n+KOho8a8oP9qxtzfvQ9iZ4dpBOOKpE9vscS12wJAlen93AGB6esR7VaLxDjExRP
# yL1pguQ8ZZ1gEXXbXO62djKo3IViobtD08KmCXTzQ6TVquLleJzqgjp+A0THnYAe
# J9Rlja7LpsO9MYSxmRE9WcQccC+sAGn/t/ufB0tL8zR43FvfhbF5H0PzBBY0H7YA
# JlzN+fgrKEEHJwMhXANNvSddhWCwvrkjNxo/80u3ySYMQR1Hav/tsXYBlk16e5nS
# fmtrFGTwhsVdy1Q6ZqEOyTni1eiYt5stEQMZFODdUNj6b9FugSZ0BK+2WN/M0CzU
# 6mKmJQgZAG/nBoRJm/XCO5OKQ6wm/4tm6F4HSH5EJ6mDT+DqETAk4GRUWTbYa2/G
# yAAOlhTMu8Xc/NhMeJ7Z99dyq0SM8pi/XpVEIv7p9yBak8ix60iCWZtDE8vlDv3M
# UfMVMTAvTS30kbS6FDN2Yyl6l8/ETdcwVIN4l02ipGzpMCtn9EQ=
# =dKUj
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 30 Jun 2023 06:05:10 AM CEST
# gpg: using RSA key
A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-vfio-
20230630' of https://github.com/legoater/qemu:
vfio/pci: Free leaked timer in vfio_realize error path
vfio/pci: Fix a segfault in vfio_realize
MAINTAINERS: Promote Cédric to VFIO co-maintainer
vfio/migration: Make VFIO migration non-experimental
vfio/migration: Reset bytes_transferred properly
vfio/pci: Call vfio_prepare_kvm_msi_virq_batch() in MSI retry path
hw/vfio/pci-quirks: Support alternate offset for GPUDirect Cliques
vfio: Implement a common device info helper
vfio/migration: Add support for switchover ack capability
vfio/migration: Add VFIO migration pre-copy support
vfio/migration: Store VFIO migration flags in VFIOMigration
vfio/migration: Refactor vfio_save_block() to return saved data size
tests: Add migration switchover ack capability test
migration: Enable switchover ack capability
migration: Implement switchover ack logic
migration: Add switchover ack capability
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson [Fri, 30 Jun 2023 06:10:43 +0000 (08:10 +0200)]
Merge tag 'pull-request-2023-06-29' of https://gitlab.com/thuth/qemu into staging
* Fix a compilation issue in the s390-ccw bios with Clang + binutils 2.40
* Create an initial stack frame for the main() function of the s390-ccw bios
* Clean up type definitions in the s390-ccw bios
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmSd1MwRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbUNAg//aO7pkzKPIUXG/g8PSzzgjYu9bDTketrQ
# P08wk1jj9CQMLN6dcnVnmzPhC4EqyrZqMYvRH4qFPLJmi0m+Jq3fEEkVzKbI3baO
# 0qQX6DNJVLn6qcgvZ8+ZjkLmuWn/lN4+MH92vdUgpkCcj5y7FB4FjoaG+Z0yZxsS
# YI6gG8D/i6fnq0zsKGMzmzHCswmN4s9qnY9a4nLV0YeMnrZJjUmUUKomWv0FP5jM
# qtLf6pRtgR4u/WD9ktwjISlOn7AKQeCYgZcMu1kBnrSWDjhLytUrv8h2JqRxGOap
# nRtdFzTvgeWKJbCX9v+XLb1bqzFj/LLgoCRzUOqV1CdBKf3JycIXyLMpTJ1+kV4J
# NnzCjnfq/LSDwwCjeg3cRBUFjGkuHBZwQzBh5m4xXBqae07UhMGpWBmhIh7qgPy2
# RXox0xK8Ot/vhYxtNojOiEW0Wp4KJElB9Wxn1Vz0kX4OXRcxHu9CDazZXTKBuBGA
# YWZ9HbsquvwNMV5pgCuXzVWW3FCzrhGgtVYREwYyBIInJaEGCWKCyMAuDXb4fkWL
# eS0Mryp3AMaJ6CidK2ELWygMkKA8xDF8pKm5jgQWRhs5jirydi1B4hPeGFsm1vUI
# TYs08XuC9p66O2Ffn2Sc/uAXbe/FQ7Ce6EbGUUetpafo9FxPhbP28hPUhkcHt68Y
# tmGzqAuwgxc=
# =oWSq
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 29 Jun 2023 09:00:28 PM CEST
# gpg: using RSA key
27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [undefined]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-06-29' of https://gitlab.com/thuth/qemu:
pc-bios: Update the s390 bios images with the recent changes
pc-bios/s390-ccw: Don't use __bss_start with the "larl" instruction
pc-bios/s390-ccw: Move the stack array into start.S
pc-bios/s390-ccw: Provide space for initial stack frame in start.S
pc-bios/s390-ccw: Fix indentation in start.S
pc-bios/s390-ccw/Makefile: Use -z noexecstack to silence linker warning
pc-bios/s390-ccw: Get rid of the the __u* types
s390-ccw: Getting rid of ulong
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Zhenzhong Duan [Thu, 29 Jun 2023 08:40:39 +0000 (16:40 +0800)]
vfio/pci: Free leaked timer in vfio_realize error path
When vfio_realize fails, the mmap_timer used for INTx optimization
isn't freed. As this timer isn't activated yet, the potential impact
is just a piece of leaked memory.
Fixes:
ea486926b07d ("vfio-pci: Update slow path INTx algorithm timer related")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Zhenzhong Duan [Thu, 29 Jun 2023 08:40:38 +0000 (16:40 +0800)]
vfio/pci: Fix a segfault in vfio_realize
The kvm irqchip notifier is only registered if the device supports
INTx, however it's unconditionally removed in vfio realize error
path. If the assigned device does not support INTx, this will cause
QEMU to crash when vfio realize fails. Change it to conditionally
remove the notifier only if the notify hook is setup.
Before fix:
(qemu) device_add vfio-pci,host=81:11.1,id=vfio1,bus=root1,xres=1
Connection closed by foreign host.
After fix:
(qemu) device_add vfio-pci,host=81:11.1,id=vfio1,bus=root1,xres=1
Error: vfio 0000:81:11.1: xres and yres properties require display=on
(qemu)
Fixes:
c5478fea27ac ("vfio/pci: Respond to KVM irqchip change notifier")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Alex Williamson [Wed, 28 Jun 2023 17:29:32 +0000 (11:29 -0600)]
MAINTAINERS: Promote Cédric to VFIO co-maintainer
Cédric has stepped up involvement in vfio, reviewing and managing
patches, as well as pull requests. This work deserves gratitude and
punishment with a promotion to co-maintainer ;)
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 28 Jun 2023 07:31:12 +0000 (10:31 +0300)]
vfio/migration: Make VFIO migration non-experimental
The major parts of VFIO migration are supported today in QEMU. This
includes basic VFIO migration, device dirty page tracking and precopy
support.
Thus, at this point in time, it seems appropriate to make VFIO migration
non-experimental: remove the x prefix from enable_migration property,
change it to ON_OFF_AUTO and let the default value be AUTO.
In addition, make the following adjustments:
1. When enable_migration is ON and migration is not supported, fail VFIO
device realization.
2. When enable_migration is AUTO (i.e., not explicitly enabled), require
device dirty tracking support. This is because device dirty tracking
is currently the only method to do dirty page tracking, which is
essential for migrating in a reasonable downtime. Setting
enable_migration to ON will not require device dirty tracking.
3. Make migration error and blocker messages more elaborate.
4. Remove error prints in vfio_migration_query_flags().
5. Rename trace_vfio_migration_probe() to
trace_vfio_migration_realize().
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 28 Jun 2023 07:31:11 +0000 (10:31 +0300)]
vfio/migration: Reset bytes_transferred properly
Currently, VFIO bytes_transferred is not reset properly:
1. bytes_transferred is not reset after a VM snapshot (so a migration
following a snapshot will report incorrect value).
2. bytes_transferred is a single counter for all VFIO devices, however
upon migration failure it is reset multiple times, by each VFIO
device.
Fix it by introducing a new function vfio_reset_bytes_transferred() and
calling it during migration and snapshot start.
Remove existing bytes_transferred reset in VFIO migration state
notifier, which is not needed anymore.
Fixes:
3710586caa5d ("qapi: Add VFIO devices migration stats in Migration stats")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Shameer Kolothum [Tue, 13 Jun 2023 14:09:43 +0000 (15:09 +0100)]
vfio/pci: Call vfio_prepare_kvm_msi_virq_batch() in MSI retry path
When vfio_enable_vectors() returns with less than requested nr_vectors
we retry with what kernel reported back. But the retry path doesn't
call vfio_prepare_kvm_msi_virq_batch() and this results in,
qemu-system-aarch64: vfio: Error: Failed to enable 4 MSI vectors, retry with 1
qemu-system-aarch64: ../hw/vfio/pci.c:602: vfio_commit_kvm_msi_virq_batch: Assertion `vdev->defer_kvm_irq_routing' failed
Fixes:
dc580d51f7dd ("vfio: defer to commit kvm irq routing when enable msi/msix")
Reviewed-by: Longpeng <longpeng2@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Alex Williamson [Thu, 8 Jun 2023 18:05:07 +0000 (12:05 -0600)]
hw/vfio/pci-quirks: Support alternate offset for GPUDirect Cliques
NVIDIA Turing and newer GPUs implement the MSI-X capability at the offset
previously reserved for use by hypervisors to implement the GPUDirect
Cliques capability. A revised specification provides an alternate
location. Add a config space walk to the quirk to check for conflicts,
allowing us to fall back to the new location or generate an error at the
quirk setup rather than when the real conflicting capability is added
should there be no available location.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Alex Williamson [Thu, 1 Jun 2023 14:45:06 +0000 (08:45 -0600)]
vfio: Implement a common device info helper
A common helper implementing the realloc algorithm for handling
capabilities.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Robin Voetter <robin@streamhpc.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:12:01 +0000 (14:12 +0300)]
vfio/migration: Add support for switchover ack capability
Loading of a VFIO device's data can take a substantial amount of time as
the device may need to allocate resources, prepare internal data
structures, etc. This can increase migration downtime, especially for
VFIO devices with a lot of resources.
To solve this, VFIO migration uAPI defines "initial bytes" as part of
its precopy data stream. Initial bytes can be used in various ways to
improve VFIO migration performance. For example, it can be used to
transfer device metadata to pre-allocate resources in the destination.
However, for this to work we need to make sure that all initial bytes
are sent and loaded in the destination before the source VM is stopped.
Use migration switchover ack capability to make sure a VFIO device's
initial bytes are sent and loaded in the destination before the source
stops the VM and attempts to complete the migration.
This can significantly reduce migration downtime for some devices.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:12:00 +0000 (14:12 +0300)]
vfio/migration: Add VFIO migration pre-copy support
Pre-copy support allows the VFIO device data to be transferred while the
VM is running. This helps to accommodate VFIO devices that have a large
amount of data that needs to be transferred, and it can reduce migration
downtime.
Pre-copy support is optional in VFIO migration protocol v2.
Implement pre-copy of VFIO migration protocol v2 and use it for devices
that support it. Full description of it can be found in the following
Linux commit:
4db52602a607 ("vfio: Extend the device migration protocol
with PRE_COPY").
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:11:59 +0000 (14:11 +0300)]
vfio/migration: Store VFIO migration flags in VFIOMigration
VFIO migration flags are queried once in vfio_migration_init(). Store
them in VFIOMigration so they can be used later to check the device's
migration capabilities without re-querying them.
This will be used in the next patch to check if the device supports
precopy migration.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:11:58 +0000 (14:11 +0300)]
vfio/migration: Refactor vfio_save_block() to return saved data size
Refactor vfio_save_block() to return the size of saved data on success
and -errno on error.
This will be used in next patch to implement VFIO migration pre-copy
support.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:11:57 +0000 (14:11 +0300)]
tests: Add migration switchover ack capability test
Add migration switchover ack capability test. The test runs without
devices that support this capability, but is still useful to make sure
it didn't break anything.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:11:56 +0000 (14:11 +0300)]
migration: Enable switchover ack capability
Now that switchover ack logic has been implemented, enable the
capability.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:11:55 +0000 (14:11 +0300)]
migration: Implement switchover ack logic
Implement switchover ack logic. This prevents the source from stopping
the VM and completing the migration until an ACK is received from the
destination that it's OK to do so.
To achieve this, a new SaveVMHandlers handler switchover_ack_needed()
and a new return path message MIG_RP_MSG_SWITCHOVER_ACK are added.
The switchover_ack_needed() handler is called during migration setup in
the destination to check if switchover ack is used by the migrated
device.
When switchover is approved by all migrated devices in the destination
that support this capability, the MIG_RP_MSG_SWITCHOVER_ACK return path
message is sent to the source to notify it that it's OK to do
switchover.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Avihai Horon [Wed, 21 Jun 2023 11:11:54 +0000 (14:11 +0300)]
migration: Add switchover ack capability
Migration downtime estimation is calculated based on bandwidth and
remaining migration data. This assumes that loading of migration data in
the destination takes a negligible amount of time and that downtime
depends only on network speed.
While this may be true for RAM, it's not necessarily true for other
migrated devices. For example, loading the data of a VFIO device in the
destination might require from the device to allocate resources, prepare
internal data structures and so on. These operations can take a
significant amount of time which can increase migration downtime.
This patch adds a new capability "switchover ack" that prevents the
source from stopping the VM and completing the migration until an ACK
is received from the destination that it's OK to do so.
This can be used by migrated devices in various ways to reduce downtime.
For example, a device can send initial precopy metadata to pre-allocate
resources in the destination and use this capability to make sure that
the pre-allocation is completed before the source VM is stopped, so it
will have full effect.
This new capability relies on the return path capability to communicate
from the destination back to the source.
The actual implementation of the capability will be added in the
following patches.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Thomas Huth [Thu, 29 Jun 2023 10:01:56 +0000 (12:01 +0200)]
pc-bios: Update the s390 bios images with the recent changes
The startup code of the bios has slightly been changed, apart
from that, there should not be any functional changes this time.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Thomas Huth [Tue, 27 Jun 2023 07:47:03 +0000 (09:47 +0200)]
pc-bios/s390-ccw: Don't use __bss_start with the "larl" instruction
start.S currently cannot be compiled with Clang 16 and binutils 2.40:
ld: start.o(.text+0x8): misaligned symbol `__bss_start' (0xc1e5) for
relocation R_390_PC32DBL
According to the built-in linker script of ld, the symbol __bss_start
can actually point *before* the .bss section and does not need to have
any alignment, so in certain situations (like when using the internal
assembler of Clang), the __bss_start symbol can indeed be unaligned
and thus it is not suitable for being used with the "larl" instruction
that needs an address that is at least aligned to halfwords.
The problem went unnoticed so far since binutils <= 2.39 did not
check the alignment, but starting with binutils 2.40, such unaligned
addresses are now refused.
Fix it by loading the address indirectly instead.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2216662
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Suggested-by: Andreas Krebbel <andreas.krebbel@de.ibm.com>
Message-Id: <
20230629104821.194859-8-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Thomas Huth [Tue, 27 Jun 2023 07:47:02 +0000 (09:47 +0200)]
pc-bios/s390-ccw: Move the stack array into start.S
The stack array is only referenced from the start-up code (which is
shared between the s390-ccw.img and the s390-netboot.img), but it is
currently declared twice, once in main.c and once in netmain.c.
It makes more sense to declare this in start.S instead - which will
also be helpful in the next patch, since we need to mention the .bss
section in start.S in that patch.
While we're at it, let's also drop the huge alignment of the stack,
since there is no technical requirement for aligning it to page
boundaries.
Message-Id: <
20230627074703.99608-4-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Thomas Huth [Tue, 27 Jun 2023 07:47:01 +0000 (09:47 +0200)]
pc-bios/s390-ccw: Provide space for initial stack frame in start.S
Providing the space of a stack frame is the duty of the caller,
so we should reserve 160 bytes before jumping into the main function.
Otherwise the main() function might write past the stack array.
While we're at it, add a proper STACK_SIZE macro for the stack size
instead of using magic numbers (this is also required for the following
patch).
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <
20230627074703.99608-3-thuth@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Thomas Huth [Tue, 27 Jun 2023 07:47:00 +0000 (09:47 +0200)]
pc-bios/s390-ccw: Fix indentation in start.S
start.S is currently indented with a mixture of spaces and tabs, which
is quite ugly. QEMU coding style says indentation should be 4 spaces,
and this is also what we are using in the assembler files in the
tests/tcg/s390x/ folder already, so let's adjust start.S accordingly.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <
20230627074703.99608-2-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Thomas Huth [Thu, 22 Jun 2023 13:08:22 +0000 (15:08 +0200)]
pc-bios/s390-ccw/Makefile: Use -z noexecstack to silence linker warning
Recent versions of ld complain when linking the s390-ccw bios:
/usr/bin/ld: warning: start.o: missing .note.GNU-stack section implies
executable stack
/usr/bin/ld: NOTE: This behaviour is deprecated and will be removed in
a future version of the linker
We can silence the warning by telling the linker to mark the stack
as not executable.
Message-Id: <
20230622130822.396793-1-thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Thomas Huth [Tue, 27 Jun 2023 11:41:01 +0000 (13:41 +0200)]
pc-bios/s390-ccw: Get rid of the the __u* types
The types starting with double underscores have likely been
introduced into the s390-ccw bios to be able to re-use structs
from the Linux kernel in the past, but the corresponding structs
in cio.h have been changed there a long time ago already to not
use the variants with the double underscores anymore:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/diff/drivers/s390/cio/cio.h?id=
cd6b4f27b9bb2a
So it would be good to replace these in the s390-ccw bios now, too.
Message-Id: <
20230627114101.122231-1-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>