MIPS: kprobes: flush_insn_slot should flush only if probe initialised

[ Upstream commit 698b851073ddf5a894910d63ca04605e0473414e ]

When ftrace is used with kprobes, it is possible for a kprobe to contain
an invalid location (ie. only initialised to 0 and not to a specific
location in the code). Trying to perform a cache flush on such location
leads to a crash r4k_flush_icache_range().

Fixes: c1bf207d6ee1 ("MIPS: kprobe: Add support.")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16296/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: mm: adjust PKMAP location

[ Upstream commit c56e7a4c3e77f6fbd9b55c06c14eda65aae58958 ]

Space reserved for PKMap should span from PKMAP_BASE to FIXADDR_START.
For large page sizes this is not the case as eg. for 64k pages the range
currently defined is from 0xfe000000 to 0x102000000(!!) which obviously
isn't right.
Remove the hardcoded location and set the BASE address as an offset from
FIXADDR_START.

Since all PKMAP ptes have to be placed in a contiguous memory, ensure
that this is the case by placing them all in a single page. This is
achieved by aligning the end address to pkmap pages count pages.

Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15950/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: mm: fixed mappings: correct initialisation

[ Upstream commit 71eb989ab5a110df8bcbb9609bacde73feacbedd ]

fixrange_init operates at PMD-granularity and expects the addresses to
be PMD-size aligned, but currently that might not be the case for
PKMAP_BASE unless it is defined properly, so ensure a correct alignment
is used before passing the address to fixrange_init.

fixed mappings: only align the start address that is passed to
fixrange_init rather than the value before adding the size, as we may
end up with uninitialised upper part of the range.

Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/deadline: Use the revised wakeup rule for suspending constrained dl tasks

[ Upstream commit 3effcb4247e74a51f5d8b775a1ee4abf87cc089a ]

We have been facing some problems with self-suspending constrained
deadline tasks. The main reason is that the original CBS was not
designed for such sort of tasks.

One problem reported by Xunlei Pang takes place when a task
suspends, and then is awakened before the deadline, but so close
to the deadline that its remaining runtime can cause the task
to have an absolute density higher than allowed. In such situation,
the original CBS assumes that the task is facing an early activation,
and so it replenishes the task and set another deadline, one deadline
in the future. This rule works fine for implicit deadline tasks.
Moreover, it allows the system to adapt the period of a task in which
the external event source suffered from a clock drift.

However, this opens the window for bandwidth leakage for constrained
deadline tasks. For instance, a task with the following parameters:

  runtime   = 5 ms
  deadline  = 7 ms
  [density] = 5 / 7 = 0.71
  period    = 1000 ms

If the task runs for 1 ms, and then suspends for another 1ms,
it will be awakened with the following parameters:

  remaining runtime = 4
  laxity = 5

presenting a absolute density of 4 / 5 = 0.80.

In this case, the original CBS would assume the task had an early
wakeup. Then, CBS will reset the runtime, and the absolute deadline will
be postponed by one relative deadline, allowing the task to run.

The problem is that, if the task runs this pattern forever, it will keep
receiving bandwidth, being able to run 1ms every 2ms. Following this
behavior, the task would be able to run 500 ms in 1 sec. Thus running
more than the 5 ms / 1 sec the admission control allowed it to run.

Trying to address the self-suspending case, Luca Abeni, Giuseppe
Lipari, and Juri Lelli [1] revisited the CBS in order to deal with
self-suspending tasks. In the new approach, rather than
replenishing/postponing the absolute deadline, the revised wakeup rule
adjusts the remaining runtime, reducing it to fit into the allowed
density.

A revised version of the idea is:

At a given time t, the maximum absolute density of a task cannot be
higher than its relative density, that is:

  runtime / (deadline - t) <= dl_runtime / dl_deadline

Knowing the laxity of a task (deadline - t), it is possible to move
it to the other side of the equality, thus enabling to define max
remaining runtime a task can use within the absolute deadline, without
over-running the allowed density:

  runtime = (dl_runtime / dl_deadline) * (deadline - t)

For instance, in our previous example, the task could still run:

  runtime = ( 5 / 7 ) * 5
  runtime = 3.57 ms

Without causing damage for other deadline tasks. It is note worthy
that the laxity cannot be negative because that would cause a negative
runtime. Thus, this patch depends on the patch:

  df8eac8cafce ("sched/deadline: Throttle a constrained deadline task activated after the deadline")

Which throttles a constrained deadline task activated after the
deadline.

Finally, it is also possible to use the revised wakeup rule for
all other tasks, but that would require some more discussions
about pros and cons.

Reported-by: Xunlei Pang <xpang@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
[peterz: replaced dl_is_constrained with dl_is_implicit]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Romulo Silva de Oliveira <romulo.deoliveira@ufsc.br>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tommaso Cucinotta <tommaso.cucinotta@sssup.it>
Link: http://lkml.kernel.org/r/5c800ab3a74a168a84ee5f3f84d12a02e11383be.1495803804.git.bristot@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/core: Correct event creation with PERF_FORMAT_GROUP

[ Upstream commit ba5213ae6b88fb170c4771fef6553f759c7d8cdd ]

Andi was asking about PERF_FORMAT_GROUP vs inherited events, which led
to the discovery of a bug from commit:

  3dab77fb1bf8 ("perf: Rework/fix the whole read vs group stuff")

 -       PERF_SAMPLE_GROUP                       = 1U << 4,
 +       PERF_SAMPLE_READ                        = 1U << 4,

 -       if (attr->inherit && (attr->sample_type & PERF_SAMPLE_GROUP))
 +       if (attr->inherit && (attr->read_format & PERF_FORMAT_GROUP))

is a clear fail :/

While this changes user visible behaviour; it was previously possible
to create an inherited event with PERF_SAMPLE_READ; this is deemed
acceptible because its results were always incorrect.

Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Fixes:  3dab77fb1bf8 ("perf: Rework/fix the whole read vs group stuff")
Link: http://lkml.kernel.org/r/20170530094512.dy2nljns2uq7qa3j@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: Undo e1000e_pm_freeze if __e1000_shutdown fails

[ Upstream commit 833521ebc65b1c3092e5c0d8a97092f98eec595d ]

An error during suspend (e100e_pm_suspend),

[  429.994338] ACPI : EC: event blocked
[  429.994633] e1000e: EEE TX LPI TIMER: 00000011
[  430.955451] pci_pm_suspend(): e1000e_pm_suspend+0x0/0x30 [e1000e] returns -2
[  430.955454] dpm_run_callback(): pci_pm_suspend+0x0/0x140 returns -2
[  430.955458] PM: Device 0000:00:19.0 failed to suspend async: error -2
[  430.955581] PM: Some devices failed to suspend, or early wake event detected
[  430.957709] ACPI : EC: event unblocked

lead to complete failure:

[  432.585002] ------------[ cut here ]------------
[  432.585013] WARNING: CPU: 3 PID: 8372 at kernel/irq/manage.c:1478 __free_irq+0x9f/0x280
[  432.585015] Trying to free already-free IRQ 20
[  432.585016] Modules linked in: cdc_ncm usbnet x86_pkg_temp_thermal intel_powerclamp coretemp mii crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep lpc_ich snd_hda_core snd_pcm mei_me mei sdhci_pci sdhci i915 mmc_core e1000e ptp pps_core prime_numbers
[  432.585042] CPU: 3 PID: 8372 Comm: kworker/u16:40 Tainted: G     U          4.10.0-rc8-CI-Patchwork_3870+ #1
[  432.585044] Hardware name: LENOVO 2356GCG/2356GCG, BIOS G7ET31WW (1.13 ) 07/02/2012
[  432.585050] Workqueue: events_unbound async_run_entry_fn
[  432.585051] Call Trace:
[  432.585058]  dump_stack+0x67/0x92
[  432.585062]  __warn+0xc6/0xe0
[  432.585065]  warn_slowpath_fmt+0x4a/0x50
[  432.585070]  ? _raw_spin_lock_irqsave+0x49/0x60
[  432.585072]  __free_irq+0x9f/0x280
[  432.585075]  free_irq+0x34/0x80
[  432.585089]  e1000_free_irq+0x65/0x70 [e1000e]
[  432.585098]  e1000e_pm_freeze+0x7a/0xb0 [e1000e]
[  432.585106]  e1000e_pm_suspend+0x21/0x30 [e1000e]
[  432.585113]  pci_pm_suspend+0x71/0x140
[  432.585118]  dpm_run_callback+0x6f/0x330
[  432.585122]  ? pci_pm_freeze+0xe0/0xe0
[  432.585125]  __device_suspend+0xea/0x330
[  432.585128]  async_suspend+0x1a/0x90
[  432.585132]  async_run_entry_fn+0x34/0x160
[  432.585137]  process_one_work+0x1f4/0x6d0
[  432.585140]  ? process_one_work+0x16e/0x6d0
[  432.585143]  worker_thread+0x49/0x4a0
[  432.585145]  kthread+0x107/0x140
[  432.585148]  ? process_one_work+0x6d0/0x6d0
[  432.585150]  ? kthread_create_on_node+0x40/0x40
[  432.585154]  ret_from_fork+0x2e/0x40
[  432.585156] ---[ end trace 6712df7f8c4b9124 ]---

The unwind failures stems from commit 2800209994f8 ("e1000e: Refactor PM
flows"), but it may be a later patch that introduced the non-recoverable
behaviour.

Fixes: 2800209994f8 ("e1000e: Refactor PM flows")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99847
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: nVMX: Update vmcs12->guest_linear_address on nested VM-exit

[ Upstream commit d281e13b0bfe745a21061a194e386a949784393f ]

The guest-linear address field is set for VM exits due to attempts to
execute LMSW with a memory operand and VM exits due to attempts to
execute INS or OUTS for which the relevant segment is usable,
regardless of whether or not EPT is in use.

Fixes: 119a9c01a5922 ("KVM: nVMX: pass valid guest linear-address to the L1")
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme: fix hang in remove path

[ Upstream commit 82654b6b8ef8b93ee87a97fc562f87f081fc2f91 ]

We need to start admin queues too in nvme_kill_queues()
for avoiding hang in remove path[1].

This patch is very similar with 806f026f9b901eaf(nvme: use
blk_mq_start_hw_queues() in nvme_kill_queues()).

[1] hang stack trace
[<ffffffff813c9716>] blk_execute_rq+0x56/0x80
[<ffffffff815cb6e9>] __nvme_submit_sync_cmd+0x89/0xf0
[<ffffffff815ce7be>] nvme_set_features+0x5e/0x90
[<ffffffff815ce9f6>] nvme_configure_apst+0x166/0x200
[<ffffffff815cef45>] nvme_set_latency_tolerance+0x35/0x50
[<ffffffff8157bd11>] apply_constraint+0xb1/0xc0
[<ffffffff8157cbb4>] dev_pm_qos_constraints_destroy+0xf4/0x1f0
[<ffffffff8157b44a>] dpm_sysfs_remove+0x2a/0x60
[<ffffffff8156d951>] device_del+0x101/0x320
[<ffffffff8156db8a>] device_unregister+0x1a/0x60
[<ffffffff8156dc4c>] device_destroy+0x3c/0x50
[<ffffffff815cd295>] nvme_uninit_ctrl+0x45/0xa0
[<ffffffff815d4858>] nvme_remove+0x78/0x110
[<ffffffff81452b69>] pci_device_remove+0x39/0xb0
[<ffffffff81572935>] device_release_driver_internal+0x155/0x210
[<ffffffff81572a02>] device_release_driver+0x12/0x20
[<ffffffff815d36fb>] nvme_remove_dead_ctrl_work+0x6b/0x70
[<ffffffff810bf3bc>] process_one_work+0x18c/0x3a0
[<ffffffff810bf61e>] worker_thread+0x4e/0x3b0
[<ffffffff810c5ac9>] kthread+0x109/0x140
[<ffffffff8185800c>] ret_from_fork+0x2c/0x40
[<ffffffffffffffff>] 0xffffffffffffffff

Fixes: c5552fde102fc("nvme: Enable autonomous power state transitions")
Reported-by: Rakesh Pandit <rakesh@tuxera.com>
Tested-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-pci: fix multiple ctrl removal scheduling

[ Upstream commit 82b057caefaff2a891f821a617d939f46e03e844 ]

Commit c5f6ce97c1210 tries to address multiple resets but fails as
work_busy doesn't involve any synchronization and can fail.  This is
reproducible easily as can be seen by WARNING below which is triggered
with line:

WARN_ON(dev->ctrl.state == NVME_CTRL_RESETTING)

Allowing multiple resets can result in multiple controller removal as
well if different conditions inside nvme_reset_work fail and which
might deadlock on device_release_driver.

[  480.327007] WARNING: CPU: 3 PID: 150 at drivers/nvme/host/pci.c:1900 nvme_reset_work+0x36c/0xec0
[  480.327008] Modules linked in: rfcomm fuse nf_conntrack_netbios_ns nf_conntrack_broadcast...
[  480.327044]  btusb videobuf2_core ghash_clmulni_intel snd_hwdep cfg80211 acer_wmi hci_uart..
[  480.327065] CPU: 3 PID: 150 Comm: kworker/u16:2 Not tainted 4.12.0-rc1+ #13
[  480.327065] Hardware name: Acer Predator G9-591/Mustang_SLS, BIOS V1.10 03/03/2016
[  480.327066] Workqueue: nvme nvme_reset_work
[  480.327067] task: ffff880498ad8000 task.stack: ffffc90002218000
[  480.327068] RIP: 0010:nvme_reset_work+0x36c/0xec0
[  480.327069] RSP: 0018:ffffc9000221bdb8 EFLAGS: 00010246
[  480.327070] RAX: 0000000000460000 RBX: ffff880498a98128 RCX: dead000000000200
[  480.327070] RDX: 0000000000000001 RSI: ffff8804b1028020 RDI: ffff880498a98128
[  480.327071] RBP: ffffc9000221be50 R08: 0000000000000000 R09: 0000000000000000
[  480.327071] R10: ffffc90001963ce8 R11: 000000000000020d R12: ffff880498a98000
[  480.327072] R13: ffff880498a53500 R14: ffff880498a98130 R15: ffff880498a98128
[  480.327072] FS:  0000000000000000(0000) GS:ffff8804c1cc0000(0000) knlGS:0000000000000000
[  480.327073] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  480.327074] CR2: 00007ffcf3c37f78 CR3: 0000000001e09000 CR4: 00000000003406e0
[  480.327074] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  480.327075] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  480.327075] Call Trace:
[  480.327079]  ? __switch_to+0x227/0x400
[  480.327081]  process_one_work+0x18c/0x3a0
[  480.327082]  worker_thread+0x4e/0x3b0
[  480.327084]  kthread+0x109/0x140
[  480.327085]  ? process_one_work+0x3a0/0x3a0
[  480.327087]  ? kthread_park+0x60/0x60
[  480.327102]  ret_from_fork+0x2c/0x40
[  480.327103] Code: e8 5a dc ff ff 85 c0 41 89 c1 0f.....

This patch addresses the problem by using state of controller to
decide whether reset should be queued or not as state change is
synchronizated using controller spinlock.  Also cancel_work_sync is
used to make sure remove cancels the reset_work and waits for it to
finish.  This patch also changes return value from -ENODEV to more
appropriate -EBUSY if nvme_reset fails to change state.

Fixes: c5f6ce97c1210 ("nvme: don't schedule multiple resets")
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: imx: Add MXC_CPU_IMX6ULL and cpu_is_imx6ull

[ Upstream commit b3ea575770c7eeb259c77b6861cd14d00eb309df ]

Support for imx6ull is already present but it's based on
of_machine_is_compatible("fsl,imx6ull") checks. Add it to the MXC_CPU_*
enumeration as well.

This also fixes /sys/devices/soc0/soc_id reading "Unknown".

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: avoid genphy_aneg_done() for PHYs without clause 22 support

[ Upstream commit 41408ad519f7a2a1c5229e61f2a97f4df1b61adc ]

Avoid calling genphy_aneg_done() for PHYs that do not implement the
Clause 22 register set.

Clause 45 PHYs may implement the Clause 22 register set along with the
Clause 22 extension MMD.  Hence, we can't simply block access to the
Clause 22 functions based on the PHY being a Clause 45 PHY.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mceusb: sporadic RX truncation corruption fix

[ Upstream commit 8e175b22e8640bf3a58e071af54190b909e4a944 ]

Intermittent RX truncation and loss of IR received data. This resulted
in receive stream synchronization errors where driver attempted to
incorrectly parse IR data (eg 0x90 below) as command response.

[ 3969.139898] mceusb 1-1.2:1.0: processed IR data
[ 3969.151315] mceusb 1-1.2:1.0: rx data: 00 90 (length=2)
[ 3969.151321] mceusb 1-1.2:1.0: Unknown command 0x00 0x90
[ 3969.151336] mceusb 1-1.2:1.0: rx data: 98 0a 8d 0a 8e 0a 8e 0a 8e 0a 8e 0a 9a 0a 8e 0a 0b 3a 8e 00 80 41 59 00 00 (length=25)
[ 3969.151341] mceusb 1-1.2:1.0: Raw IR data, 24 pulse/space samples
[ 3969.151348] mceusb 1-1.2:1.0: Storing space with duration 500000

Bug trigger appears to be normal, but heavy, IR receiver use.

Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cx25840: fix unchecked return values

[ Upstream commit 35378ce143071c2a6bad4b59a000e9b9f8f6ea67 ]

In functions cx25840_initialize(), cx231xx_initialize(), and
cx23885_initialize(), the return value of create_singlethread_workqueue()
is used without validation. This may result in NULL dereference and cause
kernel crash. This patch fixes it.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxl: Unlock on error in probe

[ Upstream commit 58d876fa7181f2f393190c1d32c056b5a9d34aa2 ]

We should unlock if get_cxl_adapter() fails.

Fixes: 594ff7d067ca ("cxl: Support to flash a new image on the adapter from a guest")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

igb: fix race condition with PTP_TX_IN_PROGRESS bits

[ Upstream commit 4ccdc013b0ae04755a8f7905e0525955d52a77d0 ]

Hardware related to the igb driver has a limitation of only handling one
Tx timestamp at a time. Thus, the driver uses a state bit lock to
enforce that only one timestamp request is honored at a time.

Unfortunately this suffers from a simple race condition. The bit lock is
not cleared until after skb_tstamp_tx() is called notifying the stack of
a new Tx timestamp. Even a well behaved application which sends only one
timestamp request at once and waits for a response might wake up and
send a new packet before the bit lock is cleared. This results in
needlessly dropping some Tx timestamp requests.

We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
unlock.

To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.

This ensures that well behaved applications do not accidentally race
with the unlock bit. Obviously an application which sends multiple Tx
timestamp requests at once will still only timestamp one packet at
a time. Unfortunately there is nothing we can do about this.

Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: fix race condition around skb_tstamp_tx()

[ Upstream commit 5012863b7347866764c4a4e58b62fb05346b0d06 ]

The e1000e driver and related hardware has a limitation on Tx PTP
packets which requires we limit to timestamping a single packet at once.
We do this by verifying that we never request a new Tx timestamp while
we still have a tx_hwtstamp_skb pointer.

Unfortunately the driver suffers from a race condition around this. The
tx_hwtstamp_skb pointer is not set to NULL until after skb_tstamp_tx()
is called. This function notifies the stack and applications of a new
timestamp. Even a well behaved application that only sends a new request
when the first one is finished might be woken up and possibly send
a packet before we can free the timestamp in the driver again. The
result is that we needlessly ignore some Tx timestamp requests in this
corner case.

Fix this by assigning the tx_hwtstamp_skb pointer prior to calling
skb_tstamp_tx() and use a temporary pointer to hold the timestamped skb
until that function finishes. This ensures that the application is not
woken up until the driver is ready to begin timestamping a new packet.

This ensures that well behaved applications do not accidentally race
with condition to skip Tx timestamps. Obviously an application which
sends multiple Tx timestamp requests at once will still only timestamp
one packet at a time. Unfortunately there is nothing we can do about
this.

Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: qcom: ipq4019: fix i2c_0 node

[ Upstream commit 650df439cfb96c303328935559b2d06127a5a0b0 ]

This patch fixes two typos in the i2c_0 node for the ipq4019.
The reg property length is just 0x600. The core clock is
GCC_BLSP1_QUP1_I2C_APPS_CLK. GCC_BLSP1_QUP2_I2C_APPS_CLK is
used by the second i2c.

Fixes: e76b4284b520ba3 ("qcom: ipq4019: add i2c node to ipq4019 SoC and DK01 device tree")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tags: honor COMPILED_SOURCE with apart output directory

[ Upstream commit cbf52a3e6a8a92beec6e0c70abf4111cd8f8faf7 ]

When the kernel is compiled with an "O=" argument, the object files are
not in the source tree, but in the build tree.

This patch fixes O= build by looking for object files in the build tree.

Fixes: 923e02ecf3f8 ("scripts/tags.sh: Support compiled source")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: fix min API version for 7265D, 3168, 8000 and 8265

[ Upstream commit 15098803d38778070b8edfa5a3d5fc4fef10d0a1 ]

In a previous commit, we removed support for API versions earlier than
22 for these NICs.  By mistake, the *_UCODE_API_MIN definitions were
set to 17.  Fix that.

Fixes: 4b87e5af638b ("iwlwifi: remove support for fw older than -17 and -22")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: pcie: only use d0i3 in suspend/resume if system_pm is set to d0i3

[ Upstream commit e4c49c4937951de1cdbe35572ade40c948dec1e1 ]

We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: tt: move ucode_loaded check under mutex

[ Upstream commit d9954405758a0cbbe258d9b4d4dc12a06fa48a28 ]

The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.

Fixes: 5c89e7bc557e ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: Fix command queue number on d0i3 flow

[ Upstream commit c72c37b7f392ad7edc10b6092fa48c632ba6f4ed ]

During d0i3 flow we flush all the queue except from the command queue.
Currently, in this flow the command queue is hard coded to 9.
In DQA the command queue number has changed from 9 to 0.
Fix that.

This fixes a problem in runtime PM resume flow.

Fixes: 097129c9e625 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: f71808e_wdt: Add F71868 support

[ Upstream commit 166fbcf88fdafa02f784ec25ac64745c716b2de0 ]

This adds support for watchdog part of Fintek F71868 Super I/O chip to
f71808e_wdt driver.

The F71868 chip is, in general, very similar to a F71869, however it has
slightly different set of available reset pulse widths.

Tested on MSI A55M-P33 motherboard.

Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix firmware debug restart recording

[ Upstream commit addce854f164a68da9cb158e2e7e447705068549 ]

When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.

Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
  recording)

For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf report: Ensure the perf DSO mapping matches what libdw sees

[ Upstream commit 2538b9e2450ae255337c04356e9e0f8cb9ec48d9 ]

In some situations the libdw unwinder stopped working properly.  I.e.
with libunwind we see:

~~~~~
heaptrack_gui  2228 135073.400112:     641314 cycles:
            e8ed _dl_fixup (/usr/lib/ld-2.25.so)
           15f06 _dl_runtime_resolve_sse_vex (/usr/lib/ld-2.25.so)
           ed94c KDynamicJobTracker::KDynamicJobTracker (/home/milian/projects/compiled/kf5/lib64/libKF5KIOWidgets.so.5.35.0)
           608f3 _GLOBAL__sub_I_kdynamicjobtracker.cpp (/home/milian/projects/compiled/kf5/lib64/libKF5KIOWidgets.so.5.35.0)
            f199 call_init.part.0 (/usr/lib/ld-2.25.so)
            f2a5 _dl_init (/usr/lib/ld-2.25.so)
             db9 _dl_start_user (/usr/lib/ld-2.25.so)
~~~~~

But with libdw and without this patch this sample is not properly
unwound:

~~~~~
heaptrack_gui  2228 135073.400112:     641314 cycles:
            e8ed _dl_fixup (/usr/lib/ld-2.25.so)
           15f06 _dl_runtime_resolve_sse_vex (/usr/lib/ld-2.25.so)
           ed94c KDynamicJobTracker::KDynamicJobTracker (/home/milian/projects/compiled/kf5/lib64/libKF5KIOWidgets.so.5.35.0)
~~~~~

Debug output showed me that libdw found a module for the last frame
address, but it thinks it belongs to /usr/lib/ld-2.25.so. This patch
double-checks what libdw sees and what perf knows. If the mappings
mismatch, we now report the elf known to perf. This fixes the situation
above, and the libdw unwinder produces the same stack as libunwind.

Signed-off-by: Milian Wolff <milian.wolff@kdab.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/20170602143753.16907-1-milian.wolff@kdab.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf header: Set proper module name when build-id event found

[ Upstream commit 1deec1bd96ccd8beb04d2112a6d12fe20505c3a6 ]

When perf processes build-id event, it creates DSOs with the build-id.
But it didn't set the module short name (like '[module-name]') so when
processing a kernel mmap event of the module, it cannot found the DSO as
it only checks the short names.

That leads for perf to create a same DSO without the build-id info and
it'll lookup the system path even if the DSO is already in the build-id
cache.  After kernel was updated, perf cannot find the DSO  and cannot
show symbols in it anymore.

You can see this if you have an old data file (w/ old kernel version):

  $ perf report -i perf.data.old -v |& grep scsi_mod
  build id event received for /lib/modules/3.19.2-1-ARCH/kernel/drivers/scsi/scsi_mod.ko.gz : cafe1ce6ca13a98a5d9ed3425cde249e57a27fc1
  Failed to open /lib/modules/3.19.2-1-ARCH/kernel/drivers/scsi/scsi_mod.ko.gz, continuing without symbols
  ...

The second message didn't show the build-id.  With this patch:

  $ perf report -i perf.data.old -v |& grep scsi_mod
  build id event received for /lib/modules/3.19.2-1-ARCH/kernel/drivers/scsi/scsi_mod.ko.gz: cafe1ce6ca13a98a5d9ed3425cde249e57a27fc1
  /lib/modules/3.19.2-1-ARCH/kernel/drivers/scsi/scsi_mod.ko.gz with build id cafe1ce6ca13a98a5d9ed3425cde249e57a27fc1 not found, continuing without symbols
  ...

Now it shows the build-id but still cannot load the symbol table.  This
is a different problem which will be fixed in the next patch.

Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: kernel-team@lge.com
Link: http://lkml.kernel.org/r/20170531120105.21731-1-namhyung@kernel.org
[ Fix the build on older compilers (debian <= 8, fedora <= 21, etc) wrt kmod_path var init ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4: Check if Granular QoS per VF has been enabled before updating QP qos_vport

[ Upstream commit 269f9883fe254d109afdfc657875c456d6fabb08 ]

The Granular QoS per VF feature must be enabled in FW before it can be
used.

Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW
command) if the feature has not been enabled -- the FW returns an error if
this is attempted.

Fixes: 08068cd5683f ("net/mlx4: Added qos_vport QP configuration in VST mode")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4: Fix the check in attaching steering rules

[ Upstream commit 6dc06c08bef1c746ff8da33dab677cfbacdcad32 ]

Our previous patch (cited below) introduced a regression
for RAW Eth QPs.

Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.

Fixes: 89c557687a32 ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sit: reload iphdr in ipip6_rcv

[ Upstream commit b699d0035836f6712917a41e7ae58d84359b8ff9 ]

Since iptunnel_pull_header() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head.

Fixes: a09a4c8dd1ec ("tunnels: Remove encapsulation offloads on decap")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

macsec: check return value of skb_to_sgvec always

[ Upstream commit cda7ea6903502af34015000e16be290a79f07638 ]

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

skbuff: return -EMSGSIZE in skb_to_sgvec to prevent overflow

[ Upstream commit 48a1df65334b74bd7531f932cca5928932abf769 ]

This is a defense-in-depth measure in response to bugs like
4d6fa57b4dab ("macsec: avoid heap overflow in skb_to_sgvec"). There's
not only a potential overflow of sglist items, but also a stack overflow
potential, so we fix this by limiting the amount of recursion this function
is allowed to do. Not actually providing a bounded base case is a future
disaster that we can easily avoid here.

As a small matter of house keeping, we take this opportunity to move the
documentation comment over the actual function the documentation is for.

While this could be implemented by using an explicit stack of skbuffs,
when implementing this, the function complexity increased considerably,
and I don't think such complexity and bloat is actually worth it. So,
instead I built this and tested it on x86, x86_64, ARM, ARM64, and MIPS,
and measured the stack usage there. I also reverted the recent MIPS
changes that give it a separate IRQ stack, so that I could experience
some worst-case situations. I found that limiting it to 24 layers deep
yielded a good stack usage with room for safety, as well as being much
deeper than any driver actually ever creates.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6_tunnel: fix traffic class routing for tunnels

[ Upstream commit 5f733ee68f9a4df94775299ac6a7ab260704f6ed ]

ip6_route_output() requires that the flowlabel contains the traffic
class for policy routing.

Commit 0e9a709560db ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets") removed the code which previously added the
traffic class to the flowlabel.

The traffic class is added here because only route lookup needs the
flowlabel to contain the traffic class.

Fixes: 0e9a709560db ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Liam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bio-integrity: Do not allocate integrity context for bio w/o data

[ Upstream commit 3116a23bb30272d74ea81baf5d0ee23f602dd15b ]

If bio has no data, such as ones from blkdev_issue_flush(),
then we have nothing to protect.

This patch prevent bugon like follows:

kfree_debugcheck: out of range ptr ac1fa1d106742a5ah
kernel BUG at mm/slab.c:2773!
invalid opcode: 0000 [#1] SMP
Modules linked in: bcache
CPU: 0 PID: 4428 Comm: xfs_io Tainted: G        W       4.11.0-rc4-ext4-00041-g2ef0043-dirty #43
Hardware name: Virtuozzo KVM, BIOS seabios-1.7.5-11.vz7.4 04/01/2014
task: ffff880137786440 task.stack: ffffc90000ba8000
RIP: 0010:kfree_debugcheck+0x25/0x2a
RSP: 0018:ffffc90000babde0 EFLAGS: 00010082
RAX: 0000000000000034 RBX: ac1fa1d106742a5a RCX: 0000000000000007
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88013f3ccb40
RBP: ffffc90000babde8 R08: 0000000000000000 R09: 0000000000000000
R10: 00000000fcb76420 R11: 00000000725172ed R12: 0000000000000282
R13: ffffffff8150e766 R14: ffff88013a145e00 R15: 0000000000000001
FS:  00007fb09384bf40(0000) GS:ffff88013f200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd0172f9e40 CR3: 0000000137fa9000 CR4: 00000000000006f0
Call Trace:
 kfree+0xc8/0x1b3
 bio_integrity_free+0xc3/0x16b
 bio_free+0x25/0x66
 bio_put+0x14/0x26
 blkdev_issue_flush+0x7a/0x85
 blkdev_fsync+0x35/0x42
 vfs_fsync_range+0x8e/0x9f
 vfs_fsync+0x1c/0x1e
 do_fsync+0x31/0x4a
 SyS_fsync+0x10/0x14
 entry_SYSCALL_64_fastpath+0x1f/0xc2

Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix serial console on SNI RM400 machines

[ Upstream commit e279e6d98e0cf2c2fe008b3c29042b92f0e17b1d ]

sccnxp driver doesn't get the correct uart clock rate, if CONFIG_HAVE_CLOCK
is disabled. Correct usage of clk API to make it work with/without it.

Fixes: 90efa75f7ab0 (serial: sccnxp: Using CLK API for getting UART clock)

Suggested-by: Russell King - ARM Linux <linux@armlinux.org.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxgb4: fix incorrect cim_la output for T6

[ Upstream commit a97051f4553551d13e586ab3cb6ae13093a44a81 ]

take care of UpDbgLaRdPtr[0-3] restriction for T6.

Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/8xx: fix mpc8xx_get_irq() return on no irq

[ Upstream commit 3c29b6038828c1f4c9ecbfec14d4fc5e25f1c947 ]

IRQ 0 is a valid HW interrupt. So get_irq() shall return 0 when
there is no irq, instead of returning irq_linear_revmap(... ,0)

Fixes: f2a0bd3753dad ("[POWERPC] 8xx: powerpc port of core CPM PIC")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/omap: fix tiled buffer stride calculations

[ Upstream commit cc8dd7661ccc2d8dc88921da8e6cc7c2fcdb0341 ]

omap_gem uses page alignment for buffer stride. The related calculations
are a bit off, though, as byte stride of 4096 gets aligned to 8192,
instead of 4096.

This patch changes the code to use DIV_ROUND_UP(), which fixes those
calculations and makes them more readable.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/hfi1: fix array termination by appending NULL to attr array

[ Upstream commit c4dd4b69f55abcc8dd079f8de55d9d8c2ddbefce ]

This fixes a kernel panic when loading the hfi driver as a dynamic module.

Signed-off-by: Steven L Roberts <robers97@gmail.com>
Reviewed-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/iw_cxgb4: Avoid touch after free error in ARP failure handlers

[ Upstream commit 1dad0ebeea1cd890b8892523f736916e245b0aef ]

The patch 761e19a504af (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure()) from May 6, 2016
leads to the following static checker warning:
drivers/infiniband/hw/cxgb4/cm.c:575 abort_arp_failure()
warn: passing freed memory 'skb'

Also fixes skb leak when l2t resolution fails

Fixes: 761e19a504afa55 (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure())
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: micrel: Restore led_mode and clk_sel on resume

[ Upstream commit 79e498a9c7da0737829ff864aae44df434105676 ]

These bits seem to be lost after a suspend/resume cycle so just set them
again. Do this by splitting the handling of these bits into a function
that is also called on resume.

This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mISDN: Fix a sleep-in-atomic bug

[ Upstream commit 93818da5eed63fbc17b64080406ea53b86b23309 ]

The driver may sleep under a read spin lock, and the function call path is:
send_socklist (acquire the lock by read_lock)
  skb_copy(GFP_KERNEL) --> may sleep

To fix it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".

Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: kernel: restrict /dev/mem read() calls to linear region

[ Upstream commit 1151f838cb626005f4d69bf675dacaaa5ea909d6 ]

When running lscpu on an AArch64 system that has SMBIOS version 2.0
tables, it will segfault in the following way:

  Unable to handle kernel paging request at virtual address ffff8000bfff0000
  pgd = ffff8000f9615000
  [ffff8000bfff0000] *pgd=0000000000000000
  Internal error: Oops: 96000007 [#1] PREEMPT SMP
  Modules linked in:
  CPU: 0 PID: 1284 Comm: lscpu Not tainted 4.11.0-rc3+ #103
  Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015
  task: ffff8000fa78e800 task.stack: ffff8000f9780000
  PC is at __arch_copy_to_user+0x90/0x220
  LR is at read_mem+0xcc/0x140

This is caused by the fact that lspci issues a read() on /dev/mem at the
offset where it expects to find the SMBIOS structure array. However, this
region is classified as EFI_RUNTIME_SERVICE_DATA (as per the UEFI spec),
and so it is omitted from the linear mapping.

So let's restrict /dev/mem read/write access to those areas that are
covered by the linear region.

Reported-by: Alexander Graf <agraf@suse.de>
Fixes: 4dffbfc48d65 ("arm64/efi: mark UEFI reserved regions as MEMBLOCK_NOMAP")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qlcnic: Fix a sleep-in-atomic bug in qlcnic_82xx_hw_write_wx_2M and qlcnic_82xx_hw_read_wx_2M

[ Upstream commit 5ea6d691aac6c93b790f0905e3460d44cc4c449b ]

The driver may sleep under a write spin lock, and the function
call path is:
qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave)
  crb_win_lock
    qlcnic_pcie_sem_lock
      usleep_range
qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave)
  crb_win_lock
    qlcnic_pcie_sem_lock
      usleep_range

To fix it, the usleep_range is replaced with udelay.

Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf trace: Add mmap alias for s390

[ Upstream commit 54265664c15a68905d8d67d19205e9a767636434 ]

The s390 architecture maps sys_mmap (nr 90) into sys_old_mmap.  For this
reason perf trace can't find the proper syscall event to get args format
from and displays it wrongly as 'continued'.

To fix that fill the "alias" field with "old_mmap" for trace's mmap record
to get the correct translation.

Before:
     0.042 ( 0.011 ms): vest/43052 fstat(statbuf: 0x3ffff89fd90                ) = 0
     0.042 ( 0.028 ms): vest/43052  ... [continued]: mmap()) = 0x3fffd6e2000
     0.072 ( 0.025 ms): vest/43052 read(buf: 0x3fffd6e2000, count: 4096        ) = 6

After:
     0.045 ( 0.011 ms): fstat(statbuf: 0x3ffff8a0930                           ) = 0
     0.057 ( 0.018 ms): mmap(arg: 0x3ffff8a0858                                ) = 0x3fffd14a000
     0.076 ( 0.025 ms): read(buf: 0x3fffd14a000, count: 4096                   ) = 6

Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20170531113557.19175-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: add BMI parameters to fix calibration from DT/pre-cal

[ Upstream commit a9f5f287fa1d47d61dfa8b60f94831174b2ea4d0 ]

QCA99X0, QCA9888, QCA9984 supports calibration data in
either OTP or DT/pre-cal file. Current ath10k supports
Calibration data from OTP only.

If caldata is loaded from DT/pre-cal file, fetching board id
and applying calibration parameters like tx power gets failed.

error log:
[   15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2
[   15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2)

This patch adds calibration data support from DT/pre-cal
file.  Below parameters are used to get board id and
applying calibration parameters from cal data.

EEPROM[OTP] FLASH[DT/pre-cal file]
Cal param 0x700 0x10000
Board id 0x10 0x8000

Tested on QCA9888 with pre-cal file.

Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdkfd: NULL dereference involving create_process()

[ Upstream commit b312b2b25b6ac9e2eb03f4ca651b33108752de3a ]

We accidentally return ERR_PTR(0) which is NULL.  The caller is not
expecting that and it leads to an Oops.

Fixes: dd59239a9862 ("amdkfd: init aperture once per process")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/spufs: Fix coredump of SPU contexts

[ Upstream commit 99acc9bede06bbb2662aafff51f5b9e529fa845e ]

If a process dumps core while it has SPU contexts active then we have
code to also dump information about the SPU contexts.

Unfortunately it's been broken for 3 1/2 years, and we didn't notice. In
commit 7b1f4020d0d1 ("spufs: get rid of dump_emit() wrappers") the nread
variable was removed and rc used instead. That means when the loop exits
successfully, rc has the number of bytes read, but it's then used as the
return value for the function, which should return 0 on success.

So fix it by setting rc = 0 before returning in the success case.

Fixes: 7b1f4020d0d1 ("spufs: get rid of dump_emit() wrappers")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: Fix __set_clk_rates error print-string

[ Upstream commit ee177c5d6369f8e5d3e4793dce501cf4431313a1 ]

When failing to set a clock the printout emitted is incorrect.
"u32 rate" is formatted as %d and should be %u whereas "unsigned long
clk_set_rate()" is formatted as %ld and should be %lu as per
Documentation/printk-formats.txt.

Fixes: 2885c3b2a3da ("clk: Show correct information when fail to set clock rate")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: scpi: fix return type of __scpi_dvfs_round_rate

[ Upstream commit 7374aec95636ca39409545eba4ef5ff3125c2346 ]

The frequencies above the maximum value of signed integer(i.e. 2^31 -1)
will overflow with the current code.

This patch fixes the return type of __scpi_dvfs_round_rate from 'int'
to 'unsigned long'.

Fixes: cd52c2a4b5c4 ("clk: add support for clocks provided by SCP(System Control Processor)")
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: SVM: do not zero out segment attributes if segment is unusable or not present

[ Upstream commit d9c1b5431d5f0e07575db785a022bce91051ac1d ]

This is a fix for the problem [1], where VMCB.CPL was set to 0 and interrupt
was taken on userspace stack.  The root cause lies in the specific AMD CPU
behaviour which manifests itself as unusable segment attributes on SYSRET.
The corresponding work around for the kernel is the following:

61f01dd941ba ("x86_64, asm: Work around AMD SYSRET SS descriptor attribute issue")

In other turn virtualization side treated unusable segment incorrectly and
restored CPL from SS attributes, which were zeroed out few lines above.

In current patch it is assured only that P bit is cleared in VMCB.save state
and segment attributes are not zeroed out if segment is not presented or is
unusable, therefore CPL can be safely restored from DPL field.

This is only one part of the fix, since QEMU side should be fixed accordingly
not to zero out attributes on its side.  Corresponding patch will follow.

[1] Message id: CAJrWOzD6Xq==b-zYCDdFLgSRMPM-NkNuTSDFEtX=7MreT45i7Q@mail.gmail.com

Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Mikhail Sennikovskii <mikhail.sennikovskii@profitbricks.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: nand: check ecc->total sanity in nand_scan_tail

[ Upstream commit 79e0348c4e24fd1affdcf055e0269755580e0fcc ]

Drivers are supposed to set correct ecc->{size,strength,bytes} before
calling nand_scan_tail(), but it does not complain about ecc->total
bigger than oobsize.

In this case, chip->scan_bbt() crashes due to memory corruption, but
it is hard to debug.  It would be kind to fail it earlier with a clear
message.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: nand: gpmi: Fix gpmi_nand_init() error path

[ Upstream commit 4d02423e9afe6c46142ce98bbcaf5167316dbfbf ]

The GPMI driver is wrongly assuming that nand_release() can safely be
called on an uninitialized/unregistered NAND device.

Add a new err_nand_cleanup label in the error path and only execute if
nand_scan_tail() succeeded.

Note that we now call nand_cleanup() instead of nand_release()
(nand_release() is actually grouping the mtd_device_unregister() and
nand_cleanup() in one call) because there's no point in trying to
unregister a device that has never been registered.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: display: sun4i: Add allwinner,tcon-channel property

[ Upstream commit 22662f12768f971809b478386d9cc4947d00497a ]

The Allwinner Timings Controller has two, mutually exclusive, channels.
When the binding has been introduced, it was assumed that there would be
only a single user per channel in the system.

While this is likely for the channel 0 which only connects to LCD displays,
it turns out that the channel 1 can be connected to multiple controllers in
the SoC (HDMI and TV encoders for example). And while the simultaneous use
of HDMI and TV outputs cannot be achieved, switching from one to the other
at runtime definitely sounds plausible.

Add an extra property, allwinner,tcon-channel, to specify for a given
endpoint which TCON channel it is connected to, while falling back to the
previous mechanism if that property is missing.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/sun4i: Ignore the generic connectors for components

[ Upstream commit 49baeb074783f5bdf770dc9fac5fbb2837190583 ]

The generic connectors such as hdmi-connector doesn't have any driver in,
so if they are added to the component list, we will be waiting forever for
a non-existing driver to probe.

Add a list of the connectors we want to ignore when building our component
list.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: at91: fix clk-generated parenting

[ Upstream commit 8e56133e5c7b7a7a97f6a92d92f664d5ecd30745 ]

clk_generated_startup is called after clk_hw_register. So the first call to
get_parent will not have the correct value (i.e. 0) and because this is
cached, it may never be updated.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: df70aeef6083 ("clk: at91: add generated clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: freescale: fix potential null pointer dereference

[ Upstream commit 06d2d6431bc8d41ef5ffd8bd4b52cea9f72aed22 ]

Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.

Addresses-Coverity-ID: 1397995
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SUNRPC: ensure correct error is reported by xs_tcp_setup_socket()

[ Upstream commit 6ea44adce91526700535b3150f77f8639ae8c82d ]

If you attempt a TCP mount from an host that is unreachable in a way
that triggers an immediate error from kernel_connect(), that error
does not propagate up, instead EAGAIN is reported.

This results in call_connect_status receiving the wrong error.

A case that it easy to demonstrate is to attempt to mount from an
address that results in ENETUNREACH, but first deleting any default
route.
Without this patch, the mount.nfs process is persistently runnable
and is hard to kill.  With this patch it exits as it should.

The problem is caused by the fact that xs_tcp_force_close() eventually
calls
      xprt_wake_pending_tasks(xprt, -EAGAIN);
which causes an error return of -EAGAIN.  so when xs_tcp_setup_sock()
calls
      xprt_wake_pending_tasks(xprt, status);
the status is ignored.

Fixes: 4efdd92c9211 ("SUNRPC: Remove TCP client connection reset hack")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: interface: Validate alarm-time before handling rollover

[ Upstream commit da96aea0ed177105cb13ee83b328f6c61e061d3f ]

In function __rtc_read_alarm() its possible for an alarm time-stamp to
be invalid even after replacing missing components with current
time-stamp. The condition 'alarm->time.tm_year < 70' will trigger this
case and will cause the call to 'rtc_tm_to_time64(&alarm->time)'
return a negative value for variable t_alm.

While handling alarm rollover this negative t_alm (assumed to seconds
offset from '1970-01-01 00:00:00') is converted back to rtc_time via
rtc_time64_to_tm() which results in this error log with seemingly
garbage values:

"rtc rtc0: invalid alarm value: -2-1--1041528741
2005511117:71582844:32"

This error was generated when the rtc driver (rtc-opal in this case)
returned an alarm time-stamp of '00-00-00 00:00:00' to indicate that
the alarm is disabled. Though I have submitted a separate fix for the
rtc-opal driver, this issue may potentially impact other
existing/future rtc drivers.

To fix this issue the patch validates the alarm time-stamp just after
filling up the missing datetime components and if rtc_valid_tm() still
reports it to be invalid then bails out of the function without
handling the rollover.

Reported-by: Steve Best <sbest@redhat.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: opal: Handle disabled TPO in opal_get_tpo_time()

[ Upstream commit 6dc1cf6f932bb0ea4d8f5e913a0a401ecacd2f03 ]

On PowerNV platform when Timed-Power-On(TPO) is disabled, read of
stored TPO yields value with all date components set to '0' inside
opal_get_tpo_time(). The function opal_to_tm() then converts it to an
offset from year 1900 yielding alarm-time == "1900-00-01
00:00:00". This causes problems with __rtc_read_alarm() that
expecting an offset from "1970-00-01 00:00:00" and returned alarm-time
results in a -ve value for time64_t. Which ultimately results in this
error reported in kernel logs with a seemingly garbage value:

"rtc rtc0: invalid alarm value: -2-1--1041528741
2005511117:71582844:32"

We fix this by explicitly handling the case of all alarm date-time
components being '0' inside opal_get_tpo_time() and returning -ENOENT
in such a case. This signals generic rtc that no alarm is set and it
bails out from the alarm initialization flow without reporting the
above error.

Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reported-by: Steve Best <sbest@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40evf: fix merge error in older patch

[ Upstream commit 155b0f690051345deefc653774b739c786067d61 ]

This patch fixes a missing line that was missed while merging,
which results in a driver feature in the VF not working to
enable RSS as a negotiated feature.

Fixes: 43a3d9ba34c9c ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: m41t80: fix SQW dividers override when setting a date

[ Upstream commit 0f546b058b86ea2f661cc7a6e931cee5a29959ef ]

This patch is only relevant for RTC with the SQ_ALT feature which
means the clock output frequency divider is stored in the weekday
register.

Current implementation discards the previous dividers value and clear
them as soon as the time is set.

Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxgb4: Fix netdev_features flag

[ Upstream commit 90592b9a35836bacd34d92a3aba7958756b6a7c0 ]

GRO is not supported by Chelsio HW when rx_csum is disabled.
Update the netdev features flag when rx_csum is modified.

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxgb4: FW upgrade fixes

[ Upstream commit 26747211486c5bc7dd014c3caab206576e00c0d0 ]

Disable FW_OK flag while flashing Firmware. This will help to fix any
potential mailbox timeouts during Firmware flash.

Grab new devlog parameters after Firmware restart. When we FLASH new
Firmware onto an adapter, the new Firmware may have the Firmware Device Log
located at a different memory address or have a different size for it.

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: avoid build warning for uniprocessor

[ Upstream commit f0d7ae95fff4ab444b8433f07afc4b077ef1a285 ]

Building the driver with CONFIG_SMP disabled results in a harmless
warning:

ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]

It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.

Fixes: b665d98edc9a ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: futex: Fix undefined behaviour with FUTEX_OP_OPARG_SHIFT usage

[ Upstream commit 5f16a046f8e144c294ef98cd29d9458b5f8273e5 ]

FUTEX_OP_OPARG_SHIFT instructs the futex code to treat the 12-bit oparg
field as a shift value, potentially leading to a left shift value that
is negative or with an absolute value that is significantly larger then
the size of the type. UBSAN chokes with:

================================================================================
UBSAN: Undefined behaviour in ./arch/arm64/include/asm/futex.h:60:13
shift exponent -1 is negative
CPU: 1 PID: 1449 Comm: syz-executor0 Not tainted 4.11.0-rc4-00005-g977eb52-dirty #11
Hardware name: linux,dummy-virt (DT)
Call trace:
[<ffff200008094778>] dump_backtrace+0x0/0x538 arch/arm64/kernel/traps.c:73
[<ffff200008094cd0>] show_stack+0x20/0x30 arch/arm64/kernel/traps.c:228
[<ffff200008c194a8>] __dump_stack lib/dump_stack.c:16 [inline]
[<ffff200008c194a8>] dump_stack+0x120/0x188 lib/dump_stack.c:52
[<ffff200008cc24b8>] ubsan_epilogue+0x18/0x98 lib/ubsan.c:164
[<ffff200008cc3098>] __ubsan_handle_shift_out_of_bounds+0x250/0x294 lib/ubsan.c:421
[<ffff20000832002c>] futex_atomic_op_inuser arch/arm64/include/asm/futex.h:60 [inline]
[<ffff20000832002c>] futex_wake_op kernel/futex.c:1489 [inline]
[<ffff20000832002c>] do_futex+0x137c/0x1740 kernel/futex.c:3231
[<ffff200008320504>] SYSC_futex kernel/futex.c:3281 [inline]
[<ffff200008320504>] SyS_futex+0x114/0x268 kernel/futex.c:3249
[<ffff200008084770>] el0_svc_naked+0x24/0x28
================================================================================
syz-executor1 uses obsolete (PF_INET,SOCK_PACKET)
sock: process `syz-executor0' is using obsolete setsockopt SO_BSDCOMPAT

This patch attempts to fix some of this by:

  * Making encoded_op an unsigned type, so we can shift it left even if
    the top bit is set.

  * Casting to signed prior to shifting right when extracting oparg
    and cmparg

  * Consider only the bottom 5 bits of oparg when using it as a left-shift
    value.

Whilst I think this catches all of the issues, I'd much prefer to remove
this stuff, as I think it's unused and the bugs are copy-pasted between
a bunch of architectures.

Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

backlight: Report error on failure

[ Upstream commit 7e715c2d9c27c23f3187454157c58cf292ed103e ]

It is possible to update the backlight power and the brightness using
the sysfs and on writing it either returns the count or if the callback
function does not exist then returns the error code 'ENXIO'.

We have a situation where the userspace client is writing to the sysfs
to update the power and since the callback function exists the client
receives the return value as count and considers the operation to be
successful. That is correct as the write to the sysfs was successful.
But there is no way to know if the actual operation was done or not.

backlight_update_status() returns the error code if it fails. Pass that
to the userspace client who is trying to update the power so that the
client knows that the operation failed.

Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: imx-sdma: Handle return value of clk_prepare_enable

[ Upstream commit fb9caf370f4d0457789d13a1a1b110a8db846e5e ]

clk_prepare_enable() can fail here and we must check its return value.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/[booke|4xx]: Don't clobber TCR[WP] when setting TCR[DIE]

[ Upstream commit 6e2f03e292ef46eed2b31b0a344a91d514f9cd81 ]

Prevent a kernel panic caused by unintentionally clearing TCR watchdog
bits. At this point in the kernel boot, the watchdog may have already
been enabled by u-boot. The original code's attempt to write to the TCR
register results in an inadvertent clearing of the watchdog
configuration bits, causing the 476 to reset.

Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: filter trusted xattr for non-admin

[ Upstream commit a082c6f680da298cf075886ff032f32ccb7c5e1a ]

Filesystems filter out extended attributes in the "trusted." domain for
unprivlieged callers.

Overlay calls underlying filesystem's method with elevated privs, so need
to do the filtering in overlayfs too.

Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: i2c: Call acpi_device_fix_up_power for ACPI-enumerated devices

[ Upstream commit f3d3eab667de62572376abb1aa26316191c39929 ]

For ACPI devices which do not have a _PSC method, the ACPI subsys cannot
query their initial state at boot, so these devices are assumed to have
been put in D0 by the BIOS, but for touchscreens that is not always true.

This commit adds a call to acpi_device_fix_up_power to explicitly put
devices without a _PSC method into D0 state (for devices with a _PSC
method it is a nop). Note we only need to do this on probe, after a
resume the ACPI subsys knows the device is in D3 and will properly
put it in D0.

This fixes the SIS0817 i2c-hid touchscreen on a Peaq C1010 2-in-1
device failing to probe with a "hid_descr_cmd failed" error.

Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: conntrack: don't call iter for non-confirmed conntracks

[ Upstream commit b0feacaad13a0aa9657c37ed80991575981e2e3b ]

nf_ct_iterate_cleanup_net currently calls iter() callback also for
conntracks on the unconfirmed list, but this is unsafe.

Acesses to nf_conn are fine, but some users access the extension area
in the iter() callback, but that does only work reliably for confirmed
conntracks (ct->ext can be reallocated at any time for unconfirmed
conntrack).

The seond issue is that there is a short window where a conntrack entry
is neither on the list nor in the table: To confirm an entry, it is first
removed from the unconfirmed list, then insert into the table.

Fix this by iterating the unconfirmed list first and marking all entries
as dying, then wait for rcu grace period.

This makes sure all entries that were about to be confirmed either are
in the main table, or will be dropped soon.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/efi: Disable runtime services on kexec kernel if booted with efi=old_map

[ Upstream commit 4e52797d2efefac3271abdc54439a3435abd77b9 ]

Booting kexec kernel with "efi=old_map" in kernel command line hits
kernel panic as shown below.

 BUG: unable to handle kernel paging request at ffff88007fe78070
 IP: virt_efi_set_variable.part.7+0x63/0x1b0
 PGD 7ea28067
 PUD 7ea2b067
 PMD 7ea2d067
 PTE 0
 [...]
 Call Trace:
  virt_efi_set_variable()
  efi_delete_dummy_variable()
  efi_enter_virtual_mode()
  start_kernel()
  x86_64_start_reservations()
  x86_64_start_kernel()
  start_cpu()

[ efi=old_map was never intended to work with kexec. The problem with
  using efi=old_map is that the virtual addresses are assigned from the
  memory region used by other kernel mappings; vmalloc() space.
  Potentially there could be collisions when booting kexec if something
  else is mapped at the virtual address we allocated for runtime service
  regions in the initial boot - Matt Fleming ]

Since kexec was never intended to work with efi=old_map, disable
runtime services in kexec if booted with efi=old_map, so that we don't
panic.

Tested-by: Lee Chun-Yi <jlee@suse.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Ricardo Neri <ricardo.neri@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170526113652.21339-4-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hdlcdrv: Fix divide by zero in hdlcdrv_ioctl

[ Upstream commit fb3ce90b7d7761b6f7f28f0ff5c456ef6b5229a1 ]

syszkaller fuzzer triggered a divide by zero, when set calibration
through ioctl().

To fix it, test 'bitrate' if it is negative or 0, just return -EINVAL.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wl1251: check return from call to wl1251_acx_arp_ip_filter

[ Upstream commit ac1181c60822292176ab96912208ec9f9819faf8 ]

Currently the less than zero error check on ret is incorrect
as it is checking a far earlier ret assignment rather than the
return from the call to wl1251_acx_arp_ip_filter. Fix this by
adding in the missing assginment.

Detected by CoverityScan, CID#1164835 ("Logically dead code")

Fixes: 204cc5c44fb6 ("wl1251: implement hardware ARP filtering")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rt2x00: do not pause queue unconditionally on error path

[ Upstream commit 6dd80efd75ce7c2dbd9f117cf585ee2b33a42ee1 ]

Pausing queue without checking threshold is racy with txdone path.
Moreover we do not need pause queue on any error, but only if queue
is full - in case when we send RTS frame ( other cases of almost full
queue are already handled in rt2x00queue_write_tx_frame() ).

Patch fixes of theoretically possible problem of pausing empty
queue.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: sst: Fix the return value of 'sst_send_byte_stream_mrfld()'

[ Upstream commit eaadb1caa966a91128297b754e90b7c92b350a00 ]

In some error handling paths, an error code is assiegned to 'ret'.
However, the function always return 0.

Fix it and return the error code if such an error paths is taken.

Fixes: 3d9ff34622ba ("ASoC: Intel: sst: add stream operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: baytrail: Enable glitch filter for GPIOs used as interrupts

[ Upstream commit 9291c65b01d1c67ebd56644cb19317ad665c44b3 ]

On some systems, some PCB traces attached to GpioInts are routed in such
a way that they pick up enough interference to constantly (many times per
second) trigger.

Enabling glitch-filtering fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

backlight: tdo24m: Fix the SPI CS between transfers

[ Upstream commit 2023b0524a6310e9ea80daf085f51c71bff9289f ]

Currently the LCD display (TD035S) on the cm-x300 platform is broken and
remains blank.

The TD0245S specification requires that the chipselect is toggled
between commands sent to the panel. This was also the purpose of the
former patch of commit f64dcac0b124 ("backlight: tdo24m: ensure chip
select changes between transfers").

Unfortunately, the "cs_change" field of a SPI transfer is
misleading. Its true meaning is that for a SPI message holding multiple
transfers, the chip select is toggled between each transfer, but for the
last transfer it remains asserted.

In this driver, all the SPI messages contain exactly one transfer, which
means that each transfer is the last of its message, and as a
consequence the chip select is never toggled.

Actually, there was a second bug hidding the first one, hence the
problem was not seen until v4.6. This problem was fixed by commit
a52db659c79c ("spi: pxa2xx: Fix cs_change management") for PXA based
boards.

This fix makes the TD035S work again on a cm-x300 board. The same
applies to other PXA boards, ie. corgi and tosa.

Fixes: a52db659c79c ("spi: pxa2xx: Fix cs_change management")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

blk-mq: fix race between updating nr_hw_queues and switching io sched

[ Upstream commit fb350e0ad99359768e1e80b4784692031ec340e4 ]

In both elevator_switch_mq() and blk_mq_update_nr_hw_queues(), sched tags
can be allocated, and q->nr_hw_queue is used, and race is inevitable, for
example: blk_mq_init_sched() may trigger use-after-free on hctx, which is
freed in blk_mq_realloc_hw_ctxs() when nr_hw_queues is decreased.

This patch fixes the race be holding q->sysfs_lock.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/rdmavt: Allocate CQ memory on the correct node

[ Upstream commit db9a2c6f9b6196b889b98e961cb9a37617b11ccf ]

CQ allocation does not ensure that completion queue entries
and the completion queue structure are allocated on the correct
numa node.

Fix by allocating the rvt_cq and kernel CQ entries on the device node,
leaving the user CQ entries on the default local node.  Also ensure
CQ resizes use the correct allocator when extending a CQ.

Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: label descriptors using the device name

[ Upstream commit 24e78079bf2250874e33da2e7cfbb6db72d3caf4 ]

Some GPIO lines appear named "?" in the lsgpio dump due to their
requesting drivers not passing a reasonable label.

Most typically this happens if a device tree node just defines
gpios = <...> and not foo-gpios = <...>, the former gets named
"foo" and the latter gets named "?".

However the struct device passed in is always valid so let's
just label the GPIO with dev_name() on the device if no proper
label was passed.

Cc: Reported-by: Jason Kridner <jkridner@beagleboard.org>
Reported-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfb: fix video mode and line_length being set when loaded

[ Upstream commit 7b9faf5df0ac495a1a3d7cdb64921c179f9008ac ]

Currently, when loading the vfb module, the newly created fbdev
has a line_length of 0, and its video mode would be PSEUDOCOLOR
regardless of color depth. (The former could be worked around by
calling the FBIOPUT_VSCREENINFO ioctl with having the FBACTIVIATE_FORCE
flag set.) This patch automatically sets the line_length correctly,
and the video mode is derived from the bit depth now as well.

Thanks to Geert Uytterhoeven for confirming the bug and helping me with
the patch.

Output of `fbset -i' before the patch:
mode "1366x768-60"
    # D: 72.432 MHz, H: 47.403 kHz, V: 60.004 Hz
    geometry 1366 768 1366 768 32
    timings 13806 120 10 14 3 32 5
    rgba 8/0,8/8,8/16,8/24
endmode

Frame buffer device information:
    Name        : Virtual FB
    Address     : 0xffffaa1405d85000
    Size        : 4196352
    Type        : PACKED PIXELS
    Visual      : PSEUDOCOLOR
    XPanStep    : 1
    YPanStep    : 1
    YWrapStep   : 1
    LineLength  : 0                    <-- note this
    Accelerator : No

After:
mode "1366x768-60"
    # D: 72.432 MHz, H: 47.403 kHz, V: 60.004 Hz
    geometry 1366 768 1366 768 32
    timings 13806 120 10 14 3 32 5
    rgba 8/0,8/8,8/16,8/24
endmode

Frame buffer device information:
    Name        : Virtual FB
    Address     : 0xffffaa1405d85000
    Size        : 4196352
    Type        : PACKED PIXELS
    Visual      : TRUECOLOR
    XPanStep    : 1
    YPanStep    : 1
    YWrapStep   : 1
    LineLength  : 5464
    Accelerator : No

Signed-off-by: "Pieter \"PoroCYon\" Sluys" <pcy@national.shitposting.agency>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
[b.zolnierkie: minor fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: Fix setting TX power on monitor interfaces

[ Upstream commit 3a3713ec360138f806c6fc368d1de570f692b347 ]

Instead of calling ieee80211_recalc_txpower on monitor interfaces
directly, call it using the virtual monitor interface, if one exists.

In case of a single monitor interface given, reject setting TX power,
if no virtual monitor interface exists.

That being checked, don't warn in ieee80211_bss_info_change_notify,
after setting TX power on a monitor interface.

Fixes warning:
------------[ cut here ]------------
 WARNING: CPU: 0 PID: 2193 at net/mac80211/driver-ops.h:167
 ieee80211_bss_info_change_notify+0x111/0x190 Modules linked in: uvcvideo
 videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_core
rndis_host cdc_ether usbnet mii tp_smapi(O) thinkpad_ec(O) ohci_hcd vboxpci(O)
 vboxnetadp(O) vboxnetflt(O) v boxdrv(O) x86_pkg_temp_thermal kvm_intel kvm
 irqbypass iwldvm iwlwifi ehci_pci ehci_hcd tpm_tis tpm_tis_core tpm CPU: 0
 PID: 2193 Comm: iw Tainted: G           O    4.12.12-gentoo #2 task:
 ffff880186fd5cc0 task.stack: ffffc90001b54000 RIP:
 0010:ieee80211_bss_info_change_notify+0x111/0x190 RSP: 0018:ffffc90001b57a10
 EFLAGS: 00010246 RAX: 0000000000000006 RBX: ffff8801052ce840 RCX:
 0000000000000064 RDX: 00000000fffffffc RSI: 0000000000040000 RDI:
 ffff8801052ce840 RBP: ffffc90001b57a38 R08: 0000000000000062 R09:
 0000000000000000 R10: ffff8802144b5000 R11: ffff880049dc4614 R12:
 0000000000040000 R13: 0000000000000064 R14: ffff8802105f0760 R15:
 ffffc90001b57b48 FS:  00007f92644b4580(0000) GS:ffff88021e200000(0000)
 knlGS:0000000000000000 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007f9263c109f0 CR3: 00000001df850000 CR4: 00000000000406f0
 Call Trace:
  ieee80211_recalc_txpower+0x33/0x40
  ieee80211_set_tx_power+0x40/0x180
  nl80211_set_wiphy+0x32e/0x950

Reported-by: Peter Große <pegro@friiks.de>
Signed-off-by: Peter Große <pegro@friiks.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI: EC: Fix debugfs_create_*() usage

[ Upstream commit 3522f867c13b63cf62acdf1b8ca5664c549a716a ]

acpi_ec.gpe is "unsigned long", hence treating it as "u32" would expose
the wrong half on big-endian 64-bit systems.  Fix this by changing its
type to "u32" and removing the cast, as all other code already uses u32
or sometimes even only u8.

Fixes: 1195a098168fcacf (ACPI: Provide /sys/kernel/debug/ec/...)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/gic-v3: Fix the driver probe() fail due to disabled GICC entry

[ Upstream commit ebe2f8718007d5a1238bb3cb8141b5bb2b4d5773 ]

The ACPI specification says OS shouldn't attempt to use GICC configuration
parameters if the flag ACPI_MADT_ENABLED is cleared. The ARM64-SMP code
skips the disabled GICC entries but not causing any issue. However the
current GICv3 driver probe bails out causing kernel panic() instead of
skipping the disabled GICC interfaces. This issue happens on systems
where redistributor regions are not in the always-on power domain and
one of GICC interface marked with ACPI_MADT_ENABLED=0.

This patch does the two things to fix the panic.
  - Don't return an error in gic_acpi_match_gicc() for disabled GICC entry.
  - No need to keep GICR region information for disabled GICC entry.

Observed kernel crash on QDF2400 platform GICC entry is disabled.
Kernel crash traces:
  Kernel panic - not syncing: No interrupt controller found.
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
  [<ffff000008087770>] dump_backtrace+0x0/0x218
  [<ffff0000080879dc>] show_stack+0x14/0x20
  [<ffff00000883b078>] dump_stack+0x98/0xb8
  [<ffff0000080c5c14>] panic+0x118/0x26c
  [<ffff000008b62348>] init_IRQ+0x24/0x2c
  [<ffff000008b609fc>] start_kernel+0x230/0x394
  [<ffff000008b601e4>] __primary_switched+0x64/0x6c
  ---[ end Kernel panic - not syncing: No interrupt controller found.

Disabled GICC subtable example:
                   Subtable Type : 0B [Generic Interrupt Controller]
                          Length : 50
                        Reserved : 0000
            CPU Interface Number : 0000003D
                   Processor UID : 0000003D
           Flags (decoded below) : 00000000
               Processor Enabled : 0
 Performance Interrupt Trig Mode : 0
 Virtual GIC Interrupt Trig Mode : 0
        Parking Protocol Version : 00000000
           Performance Interrupt : 00000017
                  Parked Address : 0000000000000000
                    Base Address : 0000000000000000
        Virtual GIC Base Address : 0000000000000000
     Hypervisor GIC Base Address : 0000000000000000
           Virtual GIC Interrupt : 00000019
      Redistributor Base Address : 0000FFFF88F40000
                       ARM MPIDR : 000000000000000D
                Efficiency Class : 00
                        Reserved : 000000
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mpt3sas: Proper handling of set/clear of "ATA command pending" flag.

[ Upstream commit f49d4aed1315a7b766d855f1367142e682b0cc87 ]

1. In IO path, setting of "ATA command pending" flag early before device
   removal, invalid device handle etc., checks causes any new commands
   to be always returned with SAM_STAT_BUSY and when the driver removes
   the drive the SML issues SYNC Cache command and that command is
   always returned with SAM_STAT_BUSY and thus making SYNC Cache command
   to requeued.

2. If the driver gets an ATA PT command for a SATA drive then the driver
   set "ATA command pending" flag in device specific data structure not
   to allow any further commands until the ATA PT command is completed.
   However, after setting the flag if the driver decides to return the
   command back to upper layers without actually issuing to the firmware
   (i.e., returns from qcmd failure return paths) then the corresponding
   flag is not cleared and this prevents the driver from sending any new
   commands to the drive.

This patch fixes above two issues by setting of "ATA command pending"
flag after checking for whether device deleted, invalid device handle,
device busy with task management. And by setting "ATA command pending"
flag to false in all of the qcmd failure return paths after setting the
flag.

Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: libiscsi: Allow sd_shutdown on bad transport

[ Upstream commit d754941225a7dbc61f6dd2173fa9498049f9a7ee ]

If, for any reason, userland shuts down iscsi transport interfaces
before proper logouts - like when logging in to LUNs manually, without
logging out on server shutdown, or when automated scripts can't
umount/logout from logged LUNs - kernel will hang forever on its
sd_sync_cache() logic, after issuing the SYNCHRONIZE_CACHE cmd to all
still existent paths.

PID: 1 TASK: ffff8801a69b8000 CPU: 1 COMMAND: "systemd-shutdow"
 #0 [ffff8801a69c3a30] __schedule at ffffffff8183e9ee
 #1 [ffff8801a69c3a80] schedule at ffffffff8183f0d5
 #2 [ffff8801a69c3a98] schedule_timeout at ffffffff81842199
 #3 [ffff8801a69c3b40] io_schedule_timeout at ffffffff8183e604
 #4 [ffff8801a69c3b70] wait_for_completion_io_timeout at ffffffff8183fc6c
 #5 [ffff8801a69c3bd0] blk_execute_rq at ffffffff813cfe10
 #6 [ffff8801a69c3c88] scsi_execute at ffffffff815c3fc7
 #7 [ffff8801a69c3cc8] scsi_execute_req_flags at ffffffff815c60fe
 #8 [ffff8801a69c3d30] sd_sync_cache at ffffffff815d37d7
 #9 [ffff8801a69c3da8] sd_shutdown at ffffffff815d3c3c

This happens because iscsi_eh_cmd_timed_out(), the transport layer
timeout helper, would tell the queue timeout function (scsi_times_out)
to reset the request timer over and over, until the session state is
back to logged in state. Unfortunately, during server shutdown, this
might never happen again.

Other option would be "not to handle" the issue in the transport
layer. That would trigger the error handler logic, which would also need
the session state to be logged in again.

Best option, for such case, is to tell upper layers that the command was
handled during the transport layer error handler helper, marking it as
DID_NO_CONNECT, which will allow completion and inform about the
problem.

After the session was marked as ISCSI_STATE_FAILED, due to the first
timeout during the server shutdown phase, all subsequent cmds will fail
to be queued, allowing upper logic to fail faster.

Signed-off-by: Rafael David Tinoco <rafael.tinoco@canonical.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: cht_bsw_rt5645: Analog Mic support

[ Upstream commit b70b309950418437bbd2a30afd169c4f09dee3e5 ]

Various Cherry Trail boards with a rt5645 codec have an analog mic
connected to IN2P + IN2N. The mic on this boards also needs micbias to
be enabled, on some boards micbias1 is used and on others micbias2, so
we enable both.

This commit adds a new "Int Analog Mic" DAPM widget for this, so that we
do not end up enabling micbias on boards with a digital mic which uses
the already present "Int Mic" widget. Some existing UCM files already
refer to "Int Mic" for their "Internal Analog Microphones" SectionDevice,
but these don't work anyways since they enable the RECMIX BST1 Switch
instead of the BST2 switch.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: Skylake: Disable clock gating during firmware and library download

[ Upstream commit d5cc0a1fcbb5ddbef9fdd4c4a978da3254ddbf37 ]

During firmware and library download, sometimes it is observed that
firmware and library download is timed-out resulting into probe failure.

This patch disables dynamic clock gating while firmware and library
download.

Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: videobuf2-core: don't go out of the buffer range

[ Upstream commit df93dc61b0d8b19a5c9db545cf3fcc24f88dfde4 ]

Currently, there's no check if an invalid buffer range
is passed. However, while testing DVB memory mapped apps,
I got this:

   videobuf2_core: VB: num_buffers -2143943680, buffer 33, index -2143943647
   unable to handle kernel paging request at ffff888b773c0890
   IP: __vb2_queue_alloc+0x134/0x4e0 [videobuf2_core]
   PGD 4142c7067 P4D 4142c7067 PUD 0
   Oops: 0002 [#1] SMP
   Modules linked in: xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables bluetooth rfkill ecdh_generic binfmt_misc rc_dvbsky sp2 ts2020 intel_rapl x86_pkg_temp_thermal dvb_usb_dvbsky intel_powerclamp dvb_usb_v2 coretemp m88ds3103 kvm_intel i2c_mux dvb_core snd_hda_codec_hdmi crct10dif_pclmul crc32_pclmul videobuf2_vmalloc videobuf2_memops snd_hda_intel ghash_clmulni_intel videobuf2_core snd_hda_codec rc_core mei_me intel_cstate snd_hwdep snd_hda_core videodev intel_uncore snd_pcm mei media tpm_tis tpm_tis_core intel_rapl_perf tpm snd_timer lpc_ich snd soundcore kvm irqbypass libcrc32c i915 i2c_algo_bit drm_kms_helper
   e1000e ptp drm crc32c_intel video pps_core
   CPU: 3 PID: 1776 Comm: dvbv5-zap Not tainted 4.14.0+ #78
   Hardware name:                  /NUC5i7RYB, BIOS RYBDWi35.86A.0364.2017.0511.0949 05/11/2017
   task: ffff88877c73bc80 task.stack: ffffb7c402418000
   RIP: 0010:__vb2_queue_alloc+0x134/0x4e0 [videobuf2_core]
   RSP: 0018:ffffb7c40241bc60 EFLAGS: 00010246
   RAX: 0000000080360421 RBX: 0000000000000021 RCX: 000000000000000a
   RDX: ffffb7c40241bcf4 RSI: ffff888780362c60 RDI: ffff888796d8e130
   RBP: ffffb7c40241bcc8 R08: 0000000000000316 R09: 0000000000000004
   R10: ffff888780362c00 R11: 0000000000000001 R12: 000000000002f000
   R13: ffff8887758be700 R14: 0000000000021000 R15: 0000000000000001
   FS:  00007f2849024740(0000) GS:ffff888796d80000(0000) knlGS:0000000000000000
   CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
   CR2: ffff888b773c0890 CR3: 000000043beb2005 CR4: 00000000003606e0
   Call Trace:
    vb2_core_reqbufs+0x226/0x420 [videobuf2_core]
    dvb_vb2_reqbufs+0x2d/0xc0 [dvb_core]
    dvb_dvr_do_ioctl+0x98/0x1d0 [dvb_core]
    dvb_usercopy+0x53/0x1b0 [dvb_core]
    ? dvb_demux_ioctl+0x20/0x20 [dvb_core]
    ? tty_ldisc_deref+0x16/0x20
    ? tty_write+0x1f9/0x310
    ? process_echoes+0x70/0x70
    dvb_dvr_ioctl+0x15/0x20 [dvb_core]
    do_vfs_ioctl+0xa5/0x600
    SyS_ioctl+0x79/0x90
    entry_SYSCALL_64_fastpath+0x1a/0xa5
   RIP: 0033:0x7f28486f7ea7
   RSP: 002b:00007ffc13b2db18 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
   RAX: ffffffffffffffda RBX: 000055b10fc06130 RCX: 00007f28486f7ea7
   RDX: 00007ffc13b2db48 RSI: 00000000c0086f3c RDI: 0000000000000007
   RBP: 0000000000000203 R08: 000055b10df1e02c R09: 000000000000002e
   R10: 0036b42415108357 R11: 0000000000000246 R12: 0000000000000000
   R13: 00007f2849062f60 R14: 00000000000001f1 R15: 00007ffc13b2da54
   Code: 74 0a 60 8b 0a 48 83 c0 30 48 83 c2 04 89 48 d0 89 48 d4 48 39 f0 75 eb 41 8b 42 08 83 7d d4 01 41 c7 82 ec 01 00 00 ff ff ff ff <4d> 89 94 c5 88 00 00 00 74 14 83 c3 01 41 39 dc 0f 85 f1 fe ff
   RIP: __vb2_queue_alloc+0x134/0x4e0 [videobuf2_core] RSP: ffffb7c40241bc60
   CR2: ffff888b773c0890

So, add a sanity check in order to prevent going past array.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (ina2xx) Make calibration register value fixed

[ Upstream commit 5d389b125186cf254ad5b8015763ac07c151aea4 ]

Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)

Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.

Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)

Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / devfreq: Fix potential NULL pointer dereference in governor_store

[ Upstream commit 63f1e05f7fe9ca509c60154d6a833abf96eecdc9 ]

df->governor is being dereferenced before it is null checked,
hence there is a potential null pointer dereference.

Notice that df->governor is being null checked at line 1004:
if (df->governor) {, which implies it might be null.

Fix this by null checking df->governor before dereferencing it.

Addresses-Coverity-ID: 1401988 ("Dereference before null check")
Fixes: bcf23c79c4e4 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

VFS: close race between getcwd() and d_move()

[ Upstream commit 61647823aa920e395afcce4b57c32afb51456cab ]

d_move() will call __d_drop() and then __d_rehash()
on the dentry being moved.  This creates a small window
when the dentry appears to be unhashed.  Many tests
of d_unhashed() are made under ->d_lock and so are safe
from racing with this window, but some aren't.
In particular, getcwd() calls d_unlinked() (which calls
d_unhashed()) without d_lock protection, so it can race.

This races has been seen in practice with lustre, which uses d_move() as
part of name lookup.  See:
   https://jira.hpdd.intel.com/browse/LU-9735
It could race with a regular rename(), and result in ENOENT instead
of either the 'before' or 'after' name.

The race can be demonstrated with a simple program which
has two threads, one renaming a directory back and forth
while another calls getcwd() within that directory: it should never
fail, but does.  See:
  https://patchwork.kernel.org/patch/9455345/

We could fix this race by taking d_lock and rechecking when
d_unhashed() reports true.  Alternately when can remove the window,
which is the approach this patch takes.

___d_drop() is introduce which does *not* clear d_hash.pprev
so the dentry still appears to be hashed.  __d_drop() calls
___d_drop(), then clears d_hash.pprev.
__d_move() now uses ___d_drop() and only clears d_hash.pprev
when not rehashing.

Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_en: Change default QoS settings

[ Upstream commit a42b63c1ac1986f17f71bc91a6b0aaa14d4dae71 ]

Change the default mapping between TC and TCG as follows:

Prio     |             TC/TCG
         |      from             to
         |    (set by FW)      (set by SW)
---------+-----------------------------------
0        |      0/0              0/7
1        |      1/0              0/6
2        |      2/0              0/5
3        |      3/0              0/4
4        |      4/0              0/3
5        |      5/0              0/2
6        |      6/0              0/1
7        |      7/0              0/0

These new settings cause that a pause frame for any prio stops
traffic for all prios.

Fixes: 564c274c3df0 ("net/mlx4_en: DCB QoS support")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / video: Default lcd_only to true on Win8-ready and newer machines

[ Upstream commit 5928c281524fe451114e04f1dfa11246a37e859f ]

We're seeing a lot of bogus backlight interfaces on newer machines without
a LCD such as desktops, servers and HDMI sticks. This causes userspace to
show a non-functional brightness slider in e.g. the GNOME3 system menu,
which is undesirable. And, in general, we should simply just not register
a non functional backlight interface.

Checking the LCD flag causes the bogus acpi_video backlight interfaces to
go away (on the machines this was tested on).

This change sets the lcd_only option by default on any machines which
are Win8-ready, to fix this.

This is not entirely without a risk of regressions, but video_detect.c
already prefers native-backlight interfaces over the acpi_video one
on Win8-ready machines, calling acpi_video_unregister_backlight() as soon
as a native interface shows up. This is done because the ACPI backlight
interface often is broken on Win8-ready machines, because win8 does not
seem to actually use it.

So in practice we already end up not registering the ACPI backlight
interface on (most) Win8-ready machines with a LCD panel, thus this
change does not change anything for (most) machines with a LCD panel
and on machines without a LCD panel we actually don't want to register
any backlight interfaces.

This has been tested on the following machines and fixes a bogus backlight
interface showing up there:
 - Desktop with an Asrock B150M Pro4S/D3 m.b. using i5-6500 builtin gfx
 - Intel Compute Stick STK1AW32SC
 - Meegopad T08 HDMI stick

Bogus backlight interfaces have also been reported on:
 - Desktop with Asus H87I-Plus m.b.
 - Desktop with ASRock B75M-ITX m.b.
 - Desktop with Gigabyte Z87-D3HP m.b.
 - Dell PowerEdge T20 desktop

Link: https://bugzilla.redhat.com/show_bug.cgi?id=1097436
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133327
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133329
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133646
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rds; Reset rs->rs_bound_addr in rds_add_bound() failure path

[ Upstream commit 7ae0c649c47f1c5d2db8cee6dd75855970af1669 ]

If the rds_sock is not added to the bind_hash_table, we must
reset rs_bound_addr so that rds_remove_bound will not trip on
this rds_sock.

rds_add_bound() does a rds_sock_put() in this failure path, so
failing to reset rs_bound_addr will result in a socket refcount
bug, and will trigger a WARN_ON with the stack shown below when
the application subsequently tries to close the PF_RDS socket.

     WARNING: CPU: 20 PID: 19499 at net/rds/af_rds.c:496 \
rds_sock_destruct+0x15/0x30 [rds]
       :
     __sk_destruct+0x21/0x190
     rds_remove_bound.part.13+0xb6/0x140 [rds]
     rds_release+0x71/0x120 [rds]
     sock_release+0x1a/0x70
     sock_close+0xe/0x20
     __fput+0xd5/0x210
     task_work_run+0x82/0xa0
     do_exit+0x2ce/0xb30
     ? syscall_trace_enter+0x1cc/0x2b0
     do_group_exit+0x39/0xa0
     SyS_exit_group+0x10/0x10
     do_syscall_64+0x61/0x1a0

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: fix missing print session offset info

[ Upstream commit 820da5357572715c6235ba3b3daa2d5b43a1198f ]

Report offset parameter in L2TP_CMD_SESSION_GET command if
it has been configured by userspace

Fixes: 309795f4bec ("l2tp: Add netlink control API for L2TP")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf probe: Add warning message if there is unexpected event name

[ Upstream commit 9f5c6d8777a2d962b0eeacb2a16f37da6bea545b ]

This improve the error message so that user can know event-name error
before writing new events to kprobe-events interface.

E.g.
   ======
   #./perf probe -x /lib64/libc-2.25.so malloc_get_state*
   Internal error: "malloc_get_state@GLIBC_2" is an invalid event name.
     Error: Failed to add events.
   ======

Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: bhargavb <bhargavaramudu@gmail.com>
Cc: linux-rt-users@vger.kernel.org
Link: http://lkml.kernel.org/r/151275040665.24652.5188568529237584489.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thermal: power_allocator: fix one race condition issue for thermal_instances list

[ Upstream commit a5de11d67dcd268b8d0beb73dc374de5e97f0caf ]

When invoking allow_maximum_power and traverse tz->thermal_instances,
we should grab thermal_zone_device->lock to avoid race condition. For
example, during the system reboot, if the mali GPU device implements
device shutdown callback and unregister GPU devfreq cooling device,
the deleted list head may be accessed to cause panic, as the following
log shows:

[   33.551070] c3 25 (kworker/3:0) Unable to handle kernel paging request at virtual address dead000000000070
[   33.566708] c3 25 (kworker/3:0) pgd = ffffffc0ed290000
[   33.572071] c3 25 (kworker/3:0) [dead000000000070] *pgd=00000001ed292003, *pud=00000001ed292003, *pmd=0000000000000000
[   33.581515] c3 25 (kworker/3:0) Internal error: Oops: 96000004 [#1] PREEMPT SMP
[   33.599761] c3 25 (kworker/3:0) CPU: 3 PID: 25 Comm: kworker/3:0 Not tainted 4.4.35+ #912
[   33.614137] c3 25 (kworker/3:0) Workqueue: events_freezable thermal_zone_device_check
[   33.620245] c3 25 (kworker/3:0) task: ffffffc0f32e4200 ti: ffffffc0f32f0000 task.ti: ffffffc0f32f0000
[   33.629466] c3 25 (kworker/3:0) PC is at power_allocator_throttle+0x7c8/0x8a4
[   33.636609] c3 25 (kworker/3:0) LR is at power_allocator_throttle+0x808/0x8a4
[   33.643742] c3 25 (kworker/3:0) pc : [<ffffff8008683dd0>] lr : [<ffffff8008683e10>] pstate: 20000145
[   33.652874] c3 25 (kworker/3:0) sp : ffffffc0f32f3bb0
[   34.468519] c3 25 (kworker/3:0) Process kworker/3:0 (pid: 25, stack limit = 0xffffffc0f32f0020)
[   34.477220] c3 25 (kworker/3:0) Stack: (0xffffffc0f32f3bb0 to 0xffffffc0f32f4000)
[   34.819822] c3 25 (kworker/3:0) Call trace:
[   34.824021] c3 25 (kworker/3:0) Exception stack(0xffffffc0f32f39c0 to 0xffffffc0f32f3af0)
[   34.924993] c3 25 (kworker/3:0) [<ffffff8008683dd0>] power_allocator_throttle+0x7c8/0x8a4
[   34.933184] c3 25 (kworker/3:0) [<ffffff80086807f4>] handle_thermal_trip.part.25+0x70/0x224
[   34.941545] c3 25 (kworker/3:0) [<ffffff8008680a68>] thermal_zone_device_update+0xc0/0x20c
[   34.949818] c3 25 (kworker/3:0) [<ffffff8008680bd4>] thermal_zone_device_check+0x20/0x2c
[   34.957924] c3 25 (kworker/3:0) [<ffffff80080b93a4>] process_one_work+0x168/0x458
[   34.965414] c3 25 (kworker/3:0) [<ffffff80080ba068>] worker_thread+0x13c/0x4b4
[   34.972650] c3 25 (kworker/3:0) [<ffffff80080c0a4c>] kthread+0xe8/0xfc
[   34.979187] c3 25 (kworker/3:0) [<ffffff8008084e90>] ret_from_fork+0x10/0x40
[   34.986244] c3 25 (kworker/3:0) Code: f9405e73 eb1302bf d102e273 54ffc460 (b9402a61)
[   34.994339] c3 25 (kworker/3:0) ---[ end trace 32057901e3b7e1db ]---

Signed-off-by: Yi Zeng <yizeng@asrmicro.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: ls1021a: add "fsl,ls1021a-esdhc" compatible string to esdhc node

[ Upstream commit d5c7b4d5ac2237a6da7ced3adfe6b8bf769f8cc6 ]

Commit a22950c888e3 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>