OSDN Git Service
Rick Tseng [Fri, 4 Oct 2019 11:59:30 +0000 (14:59 +0300)]
usb: xhci: wait for CNR controller not ready bit in xhci resume
commit
a70bcbc322837eda1ab5994d12db941dc9733a7d upstream.
NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold.
Thus we need to wait for CNR bit to clear in xhci resume, just as in
xhci init.
[Minor changes to comment and commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Rick Tseng <rtseng@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Schmidt [Fri, 4 Oct 2019 11:59:28 +0000 (14:59 +0300)]
xhci: Check all endpoints for LPM timeout
commit
d500c63f80f2ea08ee300e57da5f2af1c13875f5 upstream.
If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep
checking further endpoints, as there might be periodic endpoints later
that return USB3_LPM_DISABLED due to shorter service intervals.
Without this, the code can set too high a maximum-exit-latency and
prevent the use of multiple USB3 cameras that should be able to work.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Schmidt <jan@centricular.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 4 Oct 2019 11:59:27 +0000 (14:59 +0300)]
xhci: Prevent device initiated U1/U2 link pm if exit latency is too long
commit
cd9d9491e835a845c1a98b8471f88d26285e0bb9 upstream.
If host/hub initiated link pm is prevented by a driver flag we still must
ensure that periodic endpoints have longer service intervals than link pm
exit latency before allowing device initiated link pm.
Fix this by continue walking and checking endpoint service interval if
xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED
While at it fix the split line error message
Tested-by: Jan Schmidt <jan@centricular.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 17:09:42 +0000 (19:09 +0200)]
USB: usb-skeleton: fix NULL-deref on disconnect
commit
bed5ef230943863b9abf5eae226a20fad9a8ff71 upstream.
The driver was using its struct usb_interface pointer as an inverted
disconnected flag and was setting it to NULL before making sure all
completion handlers had run. This could lead to NULL-pointer
dereferences in the dev_err() statements in the completion handlers
which relies on said pointer.
Fix this by using a dedicated disconnected flag.
Note that this is also addresses a NULL-pointer dereference at release()
and a struct usb_interface reference leak introduced by a recent runtime
PM fix, which depends on and should have been submitted together with
this patch.
Fixes:
4212cd74ca6f ("USB: usb-skeleton.c: remove err() usage")
Fixes:
5c290a5e42c3 ("USB: usb-skeleton: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 1 Oct 2019 08:49:05 +0000 (10:49 +0200)]
USB: usb-skeleton: fix runtime PM after driver unbind
commit
5c290a5e42c3387e82de86965784d30e6c5270fd upstream.
Since commit
c2b71462d294 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes:
c2b71462d294 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 9 Oct 2019 15:38:48 +0000 (17:38 +0200)]
USB: yurex: fix NULL-derefs on disconnect
commit
aafb00a977cf7d81821f7c9d12e04c558c22dc3c upstream.
The driver was using its struct usb_interface pointer as an inverted
disconnected flag, but was setting it to NULL without making sure all
code paths that used it were done with it.
Before commit
ef61eb43ada6 ("USB: yurex: Fix protection fault after
device removal") this included the interrupt-in completion handler, but
there are further accesses in dev_err and dev_dbg statements in
yurex_write() and the driver-data destructor (sic!).
Fix this by unconditionally stopping also the control URB at disconnect
and by using a dedicated disconnected flag.
Note that we need to take a reference to the struct usb_interface to
avoid a use-after-free in the destructor whenever the device was
disconnected while the character device was still open.
Fixes:
aadd6472d904 ("USB: yurex.c: remove dbg() usage")
Fixes:
45714104b9e8 ("USB: yurex.c: remove err() usage")
Cc: stable <stable@vger.kernel.org> # 3.5: ef61eb43ada6
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 17 Sep 2019 16:47:23 +0000 (12:47 -0400)]
USB: yurex: Don't retry on unexpected errors
commit
32a0721c6620b77504916dac0cea8ad497c4878a upstream.
According to Greg KH, it has been generally agreed that when a USB
driver encounters an unknown error (or one it can't handle directly),
it should just give up instead of going into a potentially infinite
retry loop.
The three codes -EPROTO, -EILSEQ, and -ETIME fall into this category.
They can be caused by bus errors such as packet loss or corruption,
attempting to communicate with a disconnected device, or by malicious
firmware. Nowadays the extent of packet loss or corruption is
negligible, so it should be safe for a driver to give up whenever one
of these errors occurs.
Although the yurex driver handles -EILSEQ errors in this way, it
doesn't do the same for -EPROTO (as discovered by the syzbot fuzzer)
or other unrecognized errors. This patch adjusts the driver so that
it doesn't log an error message for -EPROTO or -ETIME, and it doesn't
retry after any errors.
Reported-and-tested-by: syzbot+b24d736f18a1541ad550@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909171245410.1590-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bastien Nocera [Mon, 23 Sep 2019 16:18:43 +0000 (18:18 +0200)]
USB: rio500: Remove Rio 500 kernel driver
commit
015664d15270a112c2371d812f03f7c579b35a73 upstream.
The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.
Support for the kernel driver was removed from the upstream utilities
in 2008:
https://gitlab.freedesktop.org/hadess/rio500/commit/
943f624ab721eb8281c287650fcc9e2026f6f5db
Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Mon, 7 Oct 2019 00:58:00 +0000 (17:58 -0700)]
panic: ensure preemption is disabled during panic()
commit
20bb759a66be52cf4a9ddd17fddaf509e11490cd upstream.
Calling 'panic()' on a kernel with CONFIG_PREEMPT=y can leave the
calling CPU in an infinite loop, but with interrupts and preemption
enabled. From this state, userspace can continue to be scheduled,
despite the system being "dead" as far as the kernel is concerned.
This is easily reproducible on arm64 when booting with "nosmp" on the
command line; a couple of shell scripts print out a periodic "Ping"
message whilst another triggers a crash by writing to
/proc/sysrq-trigger:
| sysrq: Trigger a crash
| Kernel panic - not syncing: sysrq triggered crash
| CPU: 0 PID: 1 Comm: init Not tainted 5.2.15 #1
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x148
| show_stack+0x14/0x20
| dump_stack+0xa0/0xc4
| panic+0x140/0x32c
| sysrq_handle_reboot+0x0/0x20
| __handle_sysrq+0x124/0x190
| write_sysrq_trigger+0x64/0x88
| proc_reg_write+0x60/0xa8
| __vfs_write+0x18/0x40
| vfs_write+0xa4/0x1b8
| ksys_write+0x64/0xf0
| __arm64_sys_write+0x14/0x20
| el0_svc_common.constprop.0+0xb0/0x168
| el0_svc_handler+0x28/0x78
| el0_svc+0x8/0xc
| Kernel Offset: disabled
| CPU features: 0x0002,
24002004
| Memory Limit: none
| ---[ end Kernel panic - not syncing: sysrq triggered crash ]---
| Ping 2!
| Ping 1!
| Ping 1!
| Ping 2!
The issue can also be triggered on x86 kernels if CONFIG_SMP=n,
otherwise local interrupts are disabled in 'smp_send_stop()'.
Disable preemption in 'panic()' before re-enabling interrupts.
Link: http://lkml.kernel.org/r/20191002123538.22609-1-will@kernel.org
Link: https://lore.kernel.org/r/BX1W47JXPMR8.58IYW53H6M5N@dragonstone
Signed-off-by: Will Deacon <will@kernel.org>
Reported-by: Xogium <contact@xogium.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksandr Suvorov [Wed, 9 Oct 2019 14:29:41 +0000 (14:29 +0000)]
ASoC: sgtl5000: Improve VAG power and mute control
[ Upstream commit
b1f373a11d25fc9a5f7679c9b85799fe09b0dc4a ]
VAG power control is improved to fit the manual [1]. This patch fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot,
the VAG power remains off that leads to poor sound quality from line-in.
I.e. after boot:
- Connect sound source to Line-In jack;
- Connect headphone to HP jack;
- Run following commands:
$ amixer set 'Headphone' 80%
$ amixer set 'Headphone Mux' LINE_IN
Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
prevents pop during line-in muxing.
According to the data sheet [1], to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Cc: stable@vger.kernel.org
Fixes:
9b34e6cc3bc2 ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190719100524.23300-3-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johannes Berg [Fri, 20 Sep 2019 19:54:17 +0000 (21:54 +0200)]
nl80211: validate beacon head
commit
f88eb7c0d002a67ef31aeb7850b42ff69abc46dc upstream.
We currently don't validate the beacon head, i.e. the header,
fixed part and elements that are to go in front of the TIM
element. This means that the variable elements there can be
malformed, e.g. have a length exceeding the buffer size, but
most downstream code from this assumes that this has already
been checked.
Add the necessary checks to the netlink policy.
Cc: stable@vger.kernel.org
Fixes:
ed1b6cc7f80f ("cfg80211/nl80211: add beacon settings")
Link: https://lore.kernel.org/r/1569009255-I7ac7fbe9436e9d8733439eab8acbbd35e55c74ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jouni Malinen [Mon, 11 Feb 2019 14:29:04 +0000 (16:29 +0200)]
cfg80211: Use const more consistently in for_each_element macros
commit
7388afe09143210f555bdd6c75035e9acc1fab96 upstream.
Enforce the first argument to be a correct type of a pointer to struct
element and avoid unnecessary typecasts from const to non-const pointers
(the change in validate_ie_attr() is needed to make this part work). In
addition, avoid signed/unsigned comparison within for_each_element() and
mark struct element packed just in case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Thu, 7 Feb 2019 20:44:41 +0000 (21:44 +0100)]
cfg80211: add and use strongly typed element iteration macros
commit
0f3b07f027f87a38ebe5c436490095df762819be upstream.
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it and since we'll need it, also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e. it was able to parse all of
the elements successfully and no data remained.
Use for_each_element_id() in cfg80211_find_ie_match() as the
first user of this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Horia Geantă [Tue, 30 Jul 2019 05:48:33 +0000 (08:48 +0300)]
crypto: caam - fix concurrency issue in givencrypt descriptor
commit
48f89d2a2920166c35b1c0b69917dbb0390ebec7 upstream.
IV transfer from ofifo to class2 (set up at [29][30]) is not guaranteed
to be scheduled before the data transfer from ofifo to external memory
(set up at [38]:
[29]
10FA0004 ld: ind-nfifo (len=4) imm
[30]
81F00010 <nfifo_entry: ofifo->class2 type=msg len=16>
[31]
14820004 ld: ccb2-datasz len=4 offs=0 imm
[32]
00000010 data:0x00000010
[33]
8210010D operation: cls1-op aes cbc init-final enc
[34]
A8080B04 math: (seqin + math0)->vseqout len=4
[35]
28000010 seqfifold: skip len=16
[36]
A8080A04 math: (seqin + math0)->vseqin len=4
[37]
2F1E0000 seqfifold: both msg1->2-last2-last1 len=vseqinsz
[38]
69300000 seqfifostr: msg len=vseqoutsz
[39]
5C20000C seqstr: ccb2 ctx len=12 offs=0
If ofifo -> external memory transfer happens first, DECO will hang
(issuing a Watchdog Timeout error, if WDOG is enabled) waiting for
data availability in ofifo for the ofifo -> c2 ififo transfer.
Make sure IV transfer happens first by waiting for all CAAM internal
transfers to end before starting payload transfer.
New descriptor with jump command inserted at [37]:
[..]
[36]
A8080A04 math: (seqin + math0)->vseqin len=4
[37]
A1000401 jump: jsl1 all-match[!nfifopend] offset=[01] local->[38]
[38]
2F1E0000 seqfifold: both msg1->2-last2-last1 len=vseqinsz
[39]
69300000 seqfifostr: msg len=vseqoutsz
[40]
5C20000C seqstr: ccb2 ctx len=12 offs=0
[Note: the issue is present in the descriptor from the very beginning
(cf. Fixes tag). However I've marked it v4.19+ since it's the oldest
maintained kernel that the patch applies clean against.]
Cc: <stable@vger.kernel.org> # v4.19+
Fixes:
1acebad3d8db8 ("crypto: caam - faster aead implementation")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[Horia: backport to v4.4, v4.9]
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srikar Dronamraju [Wed, 4 Sep 2019 09:47:38 +0000 (15:17 +0530)]
perf stat: Fix a segmentation fault when using repeat forever
[ Upstream commit
443f2d5ba13d65ccfd879460f77941875159d154 ]
Observe a segmentation fault when 'perf stat' is asked to repeat forever
with the interval option.
Without fix:
# perf stat -r 0 -I 5000 -e cycles -a sleep 10
# time counts unit events
5.
000211692 3,13,89,82,34,157 cycles
10.
000380119 1,53,98,52,22,294 cycles
10.
040467280 17,16,79,265 cycles
Segmentation fault
This problem was only observed when we use forever option aka -r 0 and
works with limited repeats. Calling print_counter with ts being set to
NULL, is not a correct option when interval is set. Hence avoid
print_counter(NULL,..) if interval is set.
With fix:
# perf stat -r 0 -I 5000 -e cycles -a sleep 10
# time counts unit events
5.
019866622 3,15,14,43,08,697 cycles
10.
039865756 3,15,16,31,95,261 cycles
10.
059950628 1,26,05,47,158 cycles
5.
009902655 3,14,52,62,33,932 cycles
10.
019880228 3,14,52,22,89,154 cycles
10.
030543876 66,90,18,333 cycles
5.
009848281 3,14,51,98,25,437 cycles
10.
029854402 3,15,14,93,04,918 cycles
5.
009834177 3,14,51,95,92,316 cycles
Committer notes:
Did the 'git bisect' to find the cset introducing the problem to add the
Fixes tag below, and at that time the problem reproduced as:
(gdb) run stat -r0 -I500 sleep 1
<SNIP>
Program received signal SIGSEGV, Segmentation fault.
print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
866 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, csv_sep);
(gdb) bt
#0 print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866
#1 0x000000000041860a in print_counters (ts=ts@entry=0x0, argc=argc@entry=2, argv=argv@entry=0x7fffffffd640) at builtin-stat.c:938
#2 0x0000000000419a7f in cmd_stat (argc=2, argv=0x7fffffffd640, prefix=<optimized out>) at builtin-stat.c:1411
#3 0x000000000045c65a in run_builtin (p=p@entry=0x6291b8 <commands+216>, argc=argc@entry=5, argv=argv@entry=0x7fffffffd640) at perf.c:370
#4 0x000000000045c893 in handle_internal_command (argc=5, argv=0x7fffffffd640) at perf.c:429
#5 0x000000000045c8f1 in run_argv (argcp=argcp@entry=0x7fffffffd4ac, argv=argv@entry=0x7fffffffd4a0) at perf.c:473
#6 0x000000000045cac9 in main (argc=<optimized out>, argv=<optimized out>) at perf.c:588
(gdb)
Mostly the same as just before this patch:
Program received signal SIGSEGV, Segmentation fault.
0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
964 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, config->csv_sep);
(gdb) bt
#0 0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964
#1 0x0000000000588047 in perf_evlist__print_counters (evlist=0xbc9b90, config=0xa1f2a0 <stat_config>, _target=0xa1f0c0 <target>, ts=0x0, argc=2, argv=0x7fffffffd670)
at util/stat-display.c:1172
#2 0x000000000045390f in print_counters (ts=0x0, argc=2, argv=0x7fffffffd670) at builtin-stat.c:656
#3 0x0000000000456bb5 in cmd_stat (argc=2, argv=0x7fffffffd670) at builtin-stat.c:1960
#4 0x00000000004dd2e0 in run_builtin (p=0xa30e00 <commands+288>, argc=5, argv=0x7fffffffd670) at perf.c:310
#5 0x00000000004dd54d in handle_internal_command (argc=5, argv=0x7fffffffd670) at perf.c:362
#6 0x00000000004dd694 in run_argv (argcp=0x7fffffffd4cc, argv=0x7fffffffd4c0) at perf.c:406
#7 0x00000000004dda11 in main (argc=5, argv=0x7fffffffd670) at perf.c:531
(gdb)
Fixes:
d4f63a4741a8 ("perf stat: Introduce print_counters function")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.2+
Link: http://lore.kernel.org/lkml/20190904094738.9558-3-srikar@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steven Rostedt (VMware) [Wed, 28 Aug 2019 19:05:28 +0000 (15:05 -0400)]
tools lib traceevent: Do not free tep->cmdlines in add_new_comm() on failure
[ Upstream commit
e0d2615856b2046c2e8d5bfd6933f37f69703b0b ]
If the re-allocation of tep->cmdlines succeeds, then the previous
allocation of tep->cmdlines will be freed. If we later fail in
add_new_comm(), we must not free cmdlines, and also should assign
tep->cmdlines to the new allocation. Otherwise when freeing tep, the
tep->cmdlines will be pointing to garbage.
Fixes:
a6d2a61ac653a ("tools lib traceevent: Remove some die() calls")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: linux-trace-devel@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20190828191819.970121417@goodmis.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Valdis Kletnieks [Wed, 25 Sep 2019 23:45:59 +0000 (16:45 -0700)]
kernel/elfcore.c: include proper prototypes
[ Upstream commit
0f74914071ab7e7b78731ed62bf350e3a344e0a5 ]
When building with W=1, gcc properly complains that there's no prototypes:
CC kernel/elfcore.o
kernel/elfcore.c:7:17: warning: no previous prototype for 'elf_core_extra_phdrs' [-Wmissing-prototypes]
7 | Elf_Half __weak elf_core_extra_phdrs(void)
| ^~~~~~~~~~~~~~~~~~~~
kernel/elfcore.c:12:12: warning: no previous prototype for 'elf_core_write_extra_phdrs' [-Wmissing-prototypes]
12 | int __weak elf_core_write_extra_phdrs(struct coredump_params *cprm, loff_t offset)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
kernel/elfcore.c:17:12: warning: no previous prototype for 'elf_core_write_extra_data' [-Wmissing-prototypes]
17 | int __weak elf_core_write_extra_data(struct coredump_params *cprm)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
kernel/elfcore.c:22:15: warning: no previous prototype for 'elf_core_extra_data_size' [-Wmissing-prototypes]
22 | size_t __weak elf_core_extra_data_size(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Provide the include file so gcc is happy, and we don't have potential code drift
Link: http://lkml.kernel.org/r/29875.1565224705@turing-police
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
zhengbin [Wed, 14 Aug 2019 07:59:09 +0000 (15:59 +0800)]
fuse: fix memleak in cuse_channel_open
[ Upstream commit
9ad09b1976c562061636ff1e01bfc3a57aebe56b ]
If cuse_send_init fails, need to fuse_conn_put cc->fc.
cuse_channel_open->fuse_conn_init->refcount_set(&fc->count, 1)
->fuse_dev_alloc->fuse_conn_get
->fuse_dev_free->fuse_conn_put
Fixes:
cc080e9e9be1 ("fuse: introduce per-instance fuse_dev structure")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ido Schimmel [Wed, 10 Jul 2019 10:14:52 +0000 (13:14 +0300)]
thermal: Fix use-after-free when unregistering thermal zone device
[ Upstream commit
1851799e1d2978f68eea5d9dff322e121dcf59c1 ]
thermal_zone_device_unregister() cancels the delayed work that polls the
thermal zone, but it does not wait for it to finish. This is racy with
respect to the freeing of the thermal zone device, which can result in a
use-after-free [1].
Fix this by waiting for the delayed work to finish before freeing the
thermal zone device. Note that thermal_zone_device_set_polling() is
never invoked from an atomic context, so it is safe to call
cancel_delayed_work_sync() that can block.
[1]
[ +0.002221] ==================================================================
[ +0.000064] BUG: KASAN: use-after-free in __mutex_lock+0x1076/0x11c0
[ +0.000016] Read of size 8 at addr
ffff8881e48e0450 by task kworker/1:0/17
[ +0.000023] CPU: 1 PID: 17 Comm: kworker/1:0 Not tainted
5.2.0-rc6-custom-02495-g8e73ca3be4af #1701
[ +0.000010] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ +0.000016] Workqueue: events_freezable_power_ thermal_zone_device_check
[ +0.000012] Call Trace:
[ +0.000021] dump_stack+0xa9/0x10e
[ +0.000020] print_address_description.cold.2+0x9/0x25e
[ +0.000018] __kasan_report.cold.3+0x78/0x9d
[ +0.000016] kasan_report+0xe/0x20
[ +0.000016] __mutex_lock+0x1076/0x11c0
[ +0.000014] step_wise_throttle+0x72/0x150
[ +0.000018] handle_thermal_trip+0x167/0x760
[ +0.000019] thermal_zone_device_update+0x19e/0x5f0
[ +0.000019] process_one_work+0x969/0x16f0
[ +0.000017] worker_thread+0x91/0xc40
[ +0.000014] kthread+0x33d/0x400
[ +0.000015] ret_from_fork+0x3a/0x50
[ +0.000020] Allocated by task 1:
[ +0.000015] save_stack+0x19/0x80
[ +0.000015] __kasan_kmalloc.constprop.4+0xc1/0xd0
[ +0.000014] kmem_cache_alloc_trace+0x152/0x320
[ +0.000015] thermal_zone_device_register+0x1b4/0x13a0
[ +0.000015] mlxsw_thermal_init+0xc92/0x23d0
[ +0.000014] __mlxsw_core_bus_device_register+0x659/0x11b0
[ +0.000013] mlxsw_core_bus_device_register+0x3d/0x90
[ +0.000013] mlxsw_pci_probe+0x355/0x4b0
[ +0.000014] local_pci_probe+0xc3/0x150
[ +0.000013] pci_device_probe+0x280/0x410
[ +0.000013] really_probe+0x26a/0xbb0
[ +0.000013] driver_probe_device+0x208/0x2e0
[ +0.000013] device_driver_attach+0xfe/0x140
[ +0.000013] __driver_attach+0x110/0x310
[ +0.000013] bus_for_each_dev+0x14b/0x1d0
[ +0.000013] driver_register+0x1c0/0x400
[ +0.000015] mlxsw_sp_module_init+0x5d/0xd3
[ +0.000014] do_one_initcall+0x239/0x4dd
[ +0.000013] kernel_init_freeable+0x42b/0x4e8
[ +0.000012] kernel_init+0x11/0x18b
[ +0.000013] ret_from_fork+0x3a/0x50
[ +0.000015] Freed by task 581:
[ +0.000013] save_stack+0x19/0x80
[ +0.000014] __kasan_slab_free+0x125/0x170
[ +0.000013] kfree+0xf3/0x310
[ +0.000013] thermal_release+0xc7/0xf0
[ +0.000014] device_release+0x77/0x200
[ +0.000014] kobject_put+0x1a8/0x4c0
[ +0.000014] device_unregister+0x38/0xc0
[ +0.000014] thermal_zone_device_unregister+0x54e/0x6a0
[ +0.000014] mlxsw_thermal_fini+0x184/0x35a
[ +0.000014] mlxsw_core_bus_device_unregister+0x10a/0x640
[ +0.000013] mlxsw_devlink_core_bus_device_reload+0x92/0x210
[ +0.000015] devlink_nl_cmd_reload+0x113/0x1f0
[ +0.000014] genl_family_rcv_msg+0x700/0xee0
[ +0.000013] genl_rcv_msg+0xca/0x170
[ +0.000013] netlink_rcv_skb+0x137/0x3a0
[ +0.000012] genl_rcv+0x29/0x40
[ +0.000013] netlink_unicast+0x49b/0x660
[ +0.000013] netlink_sendmsg+0x755/0xc90
[ +0.000013] __sys_sendto+0x3de/0x430
[ +0.000013] __x64_sys_sendto+0xe2/0x1b0
[ +0.000013] do_syscall_64+0xa4/0x4d0
[ +0.000013] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ +0.000017] The buggy address belongs to the object at
ffff8881e48e0008
which belongs to the cache kmalloc-2k of size 2048
[ +0.000012] The buggy address is located 1096 bytes inside of
2048-byte region [
ffff8881e48e0008,
ffff8881e48e0808)
[ +0.000007] The buggy address belongs to the page:
[ +0.000012] page:
ffffea0007923800 refcount:1 mapcount:0 mapping:
ffff88823680d0c0 index:0x0 compound_mapcount: 0
[ +0.000020] flags: 0x200000000010200(slab|head)
[ +0.000019] raw:
0200000000010200 ffffea0007682008 ffffea00076ab808 ffff88823680d0c0
[ +0.000016] raw:
0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000
[ +0.000007] page dumped because: kasan: bad access detected
[ +0.000012] Memory state around the buggy address:
[ +0.000012]
ffff8881e48e0300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000012]
ffff8881e48e0380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000012] >
ffff8881e48e0400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000008] ^
[ +0.000012]
ffff8881e48e0480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000012]
ffff8881e48e0500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000007] ==================================================================
Fixes:
b1569e99c795 ("ACPI: move thermal trip handling to generic thermal layer")
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Trek [Sat, 31 Aug 2019 19:25:36 +0000 (21:25 +0200)]
drm/amdgpu: Check for valid number of registers to read
[ Upstream commit
73d8e6c7b841d9bf298c8928f228fb433676635c ]
Do not try to allocate any amount of memory requested by the user.
Instead limit it to 128 registers. Actually the longest series of
consecutive allowed registers are 48, mmGB_TILE_MODE0-31 and
mmGB_MACROTILE_MODE0-15 (0x2644-0x2673).
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=111273
Signed-off-by: Trek <trek00@inbox.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luis Henriques [Tue, 23 Jul 2019 15:50:20 +0000 (16:50 +0100)]
ceph: fix directories inode i_blkbits initialization
[ Upstream commit
750670341a24cb714e624e0fd7da30900ad93752 ]
When filling an inode with info from the MDS, i_blkbits is being
initialized using fl_stripe_unit, which contains the stripe unit in
bytes. Unfortunately, this doesn't make sense for directories as they
have fl_stripe_unit set to '0'. This means that i_blkbits will be set
to 0xff, causing an UBSAN undefined behaviour in i_blocksize():
UBSAN: Undefined behaviour in ./include/linux/fs.h:731:12
shift exponent 255 is too large for 32-bit type 'int'
Fix this by initializing i_blkbits to CEPH_BLOCK_SHIFT if fl_stripe_unit
is zero.
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Igor Druzhinin [Thu, 12 Sep 2019 18:31:51 +0000 (19:31 +0100)]
xen/pci: reserve MCFG areas earlier
[ Upstream commit
a4098bc6eed5e31e0391bcc068e61804c98138df ]
If MCFG area is not reserved in E820, Xen by default will defer its usage
until Dom0 registers it explicitly after ACPI parser recognizes it as
a reserved resource in DSDT. Having it reserved in E820 is not
mandatory according to "PCI Firmware Specification, rev 3.2" (par. 4.1.2)
and firmware is free to keep a hole in E820 in that place. Xen doesn't know
what exactly is inside this hole since it lacks full ACPI view of the
platform therefore it's potentially harmful to access MCFG region
without additional checks as some machines are known to provide
inconsistent information on the size of the region.
Now xen_mcfg_late() runs after acpi_init() which is too late as some basic
PCI enumeration starts exactly there as well. Trying to register a device
prior to MCFG reservation causes multiple problems with PCIe extended
capability initializations in Xen (e.g. SR-IOV VF BAR sizing). There are
no convenient hooks for us to subscribe to so register MCFG areas earlier
upon the first invocation of xen_add_device(). It should be safe to do once
since all the boot time buses must have their MCFG areas in MCFG table
already and we don't support PCI bus hot-plug.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chengguang Xu [Tue, 20 Aug 2019 10:03:25 +0000 (18:03 +0800)]
9p: avoid attaching writeback_fid on mmap with type PRIVATE
[ Upstream commit
c87a37ebd40b889178664c2c09cc187334146292 ]
Currently on mmap cache policy, we always attach writeback_fid
whether mmap type is SHARED or PRIVATE. However, in the use case
of kata-container which combines 9p(Guest OS) with overlayfs(Host OS),
this behavior will trigger overlayfs' copy-up when excute command
inside container.
Link: http://lkml.kernel.org/r/20190820100325.10313-1-cgxu519@zoho.com.cn
Signed-off-by: Chengguang Xu <cgxu519@zoho.com.cn>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jia-Ju Bai [Fri, 26 Jul 2019 07:48:53 +0000 (15:48 +0800)]
fs: nfs: Fix possible null-pointer dereferences in encode_attrs()
[ Upstream commit
e2751463eaa6f9fec8fea80abbdc62dbc487b3c5 ]
In encode_attrs(), there is an if statement on line 1145 to check
whether label is NULL:
if (label && (attrmask[2] & FATTR4_WORD2_SECURITY_LABEL))
When label is NULL, it is used on lines 1178-1181:
*p++ = cpu_to_be32(label->lfs);
*p++ = cpu_to_be32(label->pi);
*p++ = cpu_to_be32(label->len);
p = xdr_encode_opaque_fixed(p, label->label, label->len);
To fix these bugs, label is checked before being used.
These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sascha Hauer [Tue, 2 Jul 2019 08:00:40 +0000 (10:00 +0200)]
ima: always return negative code for error
[ Upstream commit
f5e1040196dbfe14c77ce3dfe3b7b08d2d961e88 ]
integrity_kernel_read() returns the number of bytes read. If this is
a short read then this positive value is returned from
ima_calc_file_hash_atfm(). Currently this is only indirectly called from
ima_calc_file_hash() and this function only tests for the return value
being zero or nonzero and also doesn't forward the return value.
Nevertheless there's no point in returning a positive value as an error,
so translate a short read into -EINVAL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johannes Berg [Mon, 23 Sep 2019 11:51:16 +0000 (13:51 +0200)]
cfg80211: initialize on-stack chandefs
commit
f43e5210c739fe76a4b0ed851559d6902f20ceb1 upstream.
In a few places we don't properly initialize on-stack chandefs,
resulting in EDMG data to be non-zero, which broke things.
Additionally, in a few places we rely on the driver to init the
data completely, but perhaps we shouldn't as non-EDMG drivers
may not initialize the EDMG data, also initialize it there.
Cc: stable@vger.kernel.org
Fixes:
2a38075cd0be ("nl80211: Add support for EDMG channels")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/1569239475-I2dcce394ecf873376c386a78f31c2ec8b538fa25@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 19 Sep 2019 12:12:34 +0000 (14:12 +0200)]
ieee802154: atusb: fix use-after-free at disconnect
commit
7fd25e6fc035f4b04b75bca6d7e8daa069603a76 upstream.
The disconnect callback was accessing the hardware-descriptor private
data after having having freed it.
Fixes:
7490b008d123 ("ieee802154: add support for atusb transceiver")
Cc: stable <stable@vger.kernel.org> # 4.2
Cc: Alexander Aring <alex.aring@gmail.com>
Reported-by: syzbot+f4509a9138a1472e7e80@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Sverdlin [Tue, 23 Jul 2019 07:24:01 +0000 (07:24 +0000)]
crypto: qat - Silence smp_processor_id() warning
commit
1b82feb6c5e1996513d0fb0bbb475417088b4954 upstream.
It seems that smp_processor_id() is only used for a best-effort
load-balancing, refer to qat_crypto_get_instance_node(). It's not feasible
to disable preemption for the duration of the crypto requests. Therefore,
just silence the warning. This commit is similar to
e7a9b05ca4
("crypto: cavium - Fix smp_processor_id() warnings").
Silences the following splat:
BUG: using smp_processor_id() in preemptible [
00000000] code: cryptomgr_test/2904
caller is qat_alg_ablkcipher_setkey+0x300/0x4a0 [intel_qat]
CPU: 1 PID: 2904 Comm: cryptomgr_test Tainted: P O 4.14.69 #1
...
Call Trace:
dump_stack+0x5f/0x86
check_preemption_disabled+0xd3/0xe0
qat_alg_ablkcipher_setkey+0x300/0x4a0 [intel_qat]
skcipher_setkey_ablkcipher+0x2b/0x40
__test_skcipher+0x1f3/0xb20
? cpumask_next_and+0x26/0x40
? find_busiest_group+0x10e/0x9d0
? preempt_count_add+0x49/0xa0
? try_module_get+0x61/0xf0
? crypto_mod_get+0x15/0x30
? __kmalloc+0x1df/0x1f0
? __crypto_alloc_tfm+0x116/0x180
? crypto_skcipher_init_tfm+0xa6/0x180
? crypto_create_tfm+0x4b/0xf0
test_skcipher+0x21/0xa0
alg_test_skcipher+0x3f/0xa0
alg_test.part.6+0x126/0x2a0
? finish_task_switch+0x21b/0x260
? __schedule+0x1e9/0x800
? __wake_up_common+0x8d/0x140
cryptomgr_test+0x40/0x50
kthread+0xff/0x130
? cryptomgr_notify+0x540/0x540
? kthread_create_on_node+0x70/0x70
ret_from_fork+0x24/0x50
Fixes:
ed8ccaef52 ("crypto: qat - Add support for SRIOV")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde [Tue, 13 Aug 2019 14:01:02 +0000 (16:01 +0200)]
can: mcp251x: mcp251x_hw_reset(): allow more time after a reset
commit
d84ea2123f8d27144e3f4d58cd88c9c6ddc799de upstream.
Some boards take longer than 5ms to power up after a reset, so allow
some retries attempts before giving up.
Fixes:
ff06d611a31c ("can: mcp251x: Improve mcp251x_hw_reset()")
Cc: linux-stable <stable@vger.kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Donnellan [Fri, 3 May 2019 07:52:53 +0000 (17:52 +1000)]
powerpc/powernv: Restrict OPAL symbol map to only be readable by root
commit
e7de4f7b64c23e503a8c42af98d56f2a7462bd6d upstream.
Currently the OPAL symbol map is globally readable, which seems bad as
it contains physical addresses.
Restrict it to root.
Fixes:
c8742f85125d ("powerpc/powernv: Expose OPAL firmware symbol map")
Cc: stable@vger.kernel.org # v3.19+
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190503075253.22798-1-ajd@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksandr Suvorov [Fri, 19 Jul 2019 10:05:30 +0000 (10:05 +0000)]
ASoC: Define a set of DAPM pre/post-up events
commit
cfc8f568aada98f9608a0a62511ca18d647613e2 upstream.
Prepare to use SND_SOC_DAPM_PRE_POST_PMU definition to
reduce coming code size and make it more readable.
Cc: stable@vger.kernel.org
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-2-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jack Wang [Mon, 7 Oct 2019 12:36:53 +0000 (14:36 +0200)]
KVM: nVMX: handle page fault in vmread fix
During backport
f7eea636c3d5 ("KVM: nVMX: handle page fault in vmread"),
there was a mistake the exception reference should be passed to function
kvm_write_guest_virt_system, instead of NULL, other wise, we will get
NULL pointer deref, eg
kvm-unit-test triggered a NULL pointer deref below:
[ 948.518437] kvm [24114]: vcpu0, guest rIP: 0x407ef9 kvm_set_msr_common: MSR_IA32_DEBUGCTLMSR 0x3, nop
[ 949.106464] BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
[ 949.106707] PGD 0 P4D 0
[ 949.106872] Oops: 0002 [#1] SMP
[ 949.107038] CPU: 2 PID: 24126 Comm: qemu-2.7 Not tainted 4.19.77-pserver #4.19.77-1+feature+daily+update+
20191005.1625+
a4168bb~deb9
[ 949.107283] Hardware name: Dell Inc. Precision Tower 3620/09WH54, BIOS 2.7.3 01/31/2018
[ 949.107549] RIP: 0010:kvm_write_guest_virt_system+0x12/0x40 [kvm]
[ 949.107719] Code: c0 5d 41 5c 41 5d 41 5e 83 f8 03 41 0f 94 c0 41 c1 e0 02 e9 b0 ed ff ff 0f 1f 44 00 00 48 89 f0 c6 87 59 56 00 00 01 48 89 d6 <49> c7 00 00 00 00 00 89 ca 49 c7 40 08 00 00 00 00 49 c7 40 10 00
[ 949.108044] RSP: 0018:
ffffb31b0a953cb0 EFLAGS:
00010202
[ 949.108216] RAX:
000000000046b4d8 RBX:
ffff9e9f415b0000 RCX:
0000000000000008
[ 949.108389] RDX:
ffffb31b0a953cc0 RSI:
ffffb31b0a953cc0 RDI:
ffff9e9f415b0000
[ 949.108562] RBP:
00000000d2e14928 R08:
0000000000000000 R09:
0000000000000000
[ 949.108733] R10:
0000000000000000 R11:
0000000000000000 R12:
ffffffffffffffc8
[ 949.108907] R13:
0000000000000002 R14:
ffff9e9f4f26f2e8 R15:
0000000000000000
[ 949.109079] FS:
00007eff8694c700(0000) GS:
ffff9e9f51a80000(0000) knlGS:
0000000031415928
[ 949.109318] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 949.109495] CR2:
0000000000000000 CR3:
00000003be53b002 CR4:
00000000003626e0
[ 949.109671] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 949.109845] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 949.110017] Call Trace:
[ 949.110186] handle_vmread+0x22b/0x2f0 [kvm_intel]
[ 949.110356] ? vmexit_fill_RSB+0xc/0x30 [kvm_intel]
[ 949.110549] kvm_arch_vcpu_ioctl_run+0xa98/0x1b30 [kvm]
[ 949.110725] ? kvm_vcpu_ioctl+0x388/0x5d0 [kvm]
[ 949.110901] kvm_vcpu_ioctl+0x388/0x5d0 [kvm]
[ 949.111072] do_vfs_ioctl+0xa2/0x620
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Vasily Gorbik [Thu, 19 Sep 2019 13:55:17 +0000 (15:55 +0200)]
s390/cio: exclude subchannels with no parent from pseudo check
commit
ab5758848039de9a4b249d46e4ab591197eebaf2 upstream.
ccw console is created early in start_kernel and used before css is
initialized or ccw console subchannel is registered. Until then console
subchannel does not have a parent. For that reason assume subchannels
with no parent are not pseudo subchannels. This fixes the following
kasan finding:
BUG: KASAN: global-out-of-bounds in sch_is_pseudo_sch+0x8e/0x98
Read of size 8 at addr
00000000000005e8 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted
5.3.0-rc8-07370-g6ac43dd12538 #2
Hardware name: IBM 2964 NC9 702 (z/VM 6.4.0)
Call Trace:
([<
000000000012cd76>] show_stack+0x14e/0x1e0)
[<
0000000001f7fb44>] dump_stack+0x1a4/0x1f8
[<
00000000007d7afc>] print_address_description+0x64/0x3c8
[<
00000000007d75f6>] __kasan_report+0x14e/0x180
[<
00000000018a2986>] sch_is_pseudo_sch+0x8e/0x98
[<
000000000189b950>] cio_enable_subchannel+0x1d0/0x510
[<
00000000018cac7c>] ccw_device_recognition+0x12c/0x188
[<
0000000002ceb1a8>] ccw_device_enable_console+0x138/0x340
[<
0000000002cf1cbe>] con3215_init+0x25e/0x300
[<
0000000002c8770a>] console_init+0x68a/0x9b8
[<
0000000002c6a3d6>] start_kernel+0x4fe/0x728
[<
0000000000100070>] startup_continue+0x70/0xd0
Cc: stable@vger.kernel.org
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vasily Gorbik [Tue, 17 Sep 2019 18:04:04 +0000 (20:04 +0200)]
s390/cio: avoid calling strlen on null pointer
commit
ea298e6ee8b34b3ed4366be7eb799d0650ebe555 upstream.
Fix the following kasan finding:
BUG: KASAN: global-out-of-bounds in ccwgroup_create_dev+0x850/0x1140
Read of size 1 at addr
0000000000000000 by task systemd-udevd.r/561
CPU: 30 PID: 561 Comm: systemd-udevd.r Tainted: G B
Hardware name: IBM 3906 M04 704 (LPAR)
Call Trace:
([<
0000000231b3db7e>] show_stack+0x14e/0x1a8)
[<
0000000233826410>] dump_stack+0x1d0/0x218
[<
000000023216fac4>] print_address_description+0x64/0x380
[<
000000023216f5a8>] __kasan_report+0x138/0x168
[<
00000002331b8378>] ccwgroup_create_dev+0x850/0x1140
[<
00000002332b618a>] group_store+0x3a/0x50
[<
00000002323ac706>] kernfs_fop_write+0x246/0x3b8
[<
00000002321d409a>] vfs_write+0x132/0x450
[<
00000002321d47da>] ksys_write+0x122/0x208
[<
0000000233877102>] system_call+0x2a6/0x2c8
Triggered by:
openat(AT_FDCWD, "/sys/bus/ccwgroup/drivers/qeth/group",
O_WRONLY|O_CREAT|O_TRUNC|O_CLOEXEC, 0666) = 16
write(16, "0.0.bd00,0.0.bd01,0.0.bd02", 26) = 26
The problem is that __get_next_id in ccwgroup_create_dev might set "buf"
buffer pointer to NULL and explicit check for that is required.
Cc: stable@vger.kernel.org
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vasily Gorbik [Tue, 17 Sep 2019 20:59:03 +0000 (22:59 +0200)]
s390/topology: avoid firing events before kobjs are created
commit
f3122a79a1b0a113d3aea748e0ec26f2cb2889de upstream.
arch_update_cpu_topology is first called from:
kernel_init_freeable->sched_init_smp->sched_init_domains
even before cpus has been registered in:
kernel_init_freeable->do_one_initcall->s390_smp_init
Do not trigger kobject_uevent change events until cpu devices are
actually created. Fixes the following kasan findings:
BUG: KASAN: global-out-of-bounds in kobject_uevent_env+0xb40/0xee0
Read of size 8 at addr
0000000000000020 by task swapper/0/1
BUG: KASAN: global-out-of-bounds in kobject_uevent_env+0xb36/0xee0
Read of size 8 at addr
0000000000000018 by task swapper/0/1
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G B
Hardware name: IBM 3906 M04 704 (LPAR)
Call Trace:
([<
0000000143c6db7e>] show_stack+0x14e/0x1a8)
[<
0000000145956498>] dump_stack+0x1d0/0x218
[<
000000014429fb4c>] print_address_description+0x64/0x380
[<
000000014429f630>] __kasan_report+0x138/0x168
[<
0000000145960b96>] kobject_uevent_env+0xb36/0xee0
[<
0000000143c7c47c>] arch_update_cpu_topology+0x104/0x108
[<
0000000143df9e22>] sched_init_domains+0x62/0xe8
[<
000000014644c94a>] sched_init_smp+0x3a/0xc0
[<
0000000146433a20>] kernel_init_freeable+0x558/0x958
[<
000000014599002a>] kernel_init+0x22/0x160
[<
00000001459a71d4>] ret_from_fork+0x28/0x30
[<
00000001459a71dc>] kernel_thread_starter+0x0/0x10
Cc: stable@vger.kernel.org
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Huth [Thu, 29 Aug 2019 12:25:17 +0000 (14:25 +0200)]
KVM: s390: Test for bad access register and size at the start of S390_MEM_OP
commit
a13b03bbb4575b350b46090af4dfd30e735aaed1 upstream.
If the KVM_S390_MEM_OP ioctl is called with an access register >= 16,
then there is certainly a bug in the calling userspace application.
We check for wrong access registers, but only if the vCPU was already
in the access register mode before (i.e. the SIE block has recorded
it). The check is also buried somewhere deep in the calling chain (in
the function ar_translation()), so this is somewhat hard to find.
It's better to always report an error to the userspace in case this
field is set wrong, and it's safer in the KVM code if we block wrong
values here early instead of relying on a check somewhere deep down
the calling chain, so let's add another check to kvm_s390_guest_mem_op()
directly.
We also should check that the "size" is non-zero here (thanks to Janosch
Frank for the hint!). If we do not check the size, we could call vmalloc()
with this 0 value, and this will cause a kernel warning.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Link: https://lkml.kernel.org/r/20190829122517.31042-1-thuth@redhat.com
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 7 Oct 2019 19:01:07 +0000 (21:01 +0200)]
Linux 4.4.196
Andrey Konovalov [Mon, 29 Jul 2019 13:35:01 +0000 (16:35 +0300)]
NFC: fix attrs checks in netlink interface
commit
18917d51472fe3b126a3a8f756c6b18085eb8130 upstream.
nfc_genl_deactivate_target() relies on the NFC_ATTR_TARGET_INDEX
attribute being present, but doesn't check whether it is actually
provided by the user. Same goes for nfc_genl_fw_download() and
NFC_ATTR_FIRMWARE_NAME.
This patch adds appropriate checks.
Found with syzkaller.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers [Thu, 22 Aug 2019 05:54:41 +0000 (22:54 -0700)]
smack: use GFP_NOFS while holding inode_smack::smk_lock
commit
e5bfad3d7acc5702f32aafeb388362994f4d7bd0 upstream.
inode_smack::smk_lock is taken during smack_d_instantiate(), which is
called during a filesystem transaction when creating a file on ext4.
Therefore to avoid a deadlock, all code that takes this lock must use
GFP_NOFS, to prevent memory reclaim from waiting for the filesystem
transaction to complete.
Reported-by: syzbot+0eefc1e06a77d327a056@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jann Horn [Thu, 4 Jul 2019 18:44:44 +0000 (20:44 +0200)]
Smack: Don't ignore other bprm->unsafe flags if LSM_UNSAFE_PTRACE is set
commit
3675f052b43ba51b99b85b073c7070e083f3e6fb upstream.
There is a logic bug in the current smack_bprm_set_creds():
If LSM_UNSAFE_PTRACE is set, but the ptrace state is deemed to be
acceptable (e.g. because the ptracer detached in the meantime), the other
->unsafe flags aren't checked. As far as I can tell, this means that
something like the following could work (but I haven't tested it):
- task A: create task B with fork()
- task B: set NO_NEW_PRIVS
- task B: install a seccomp filter that makes open() return 0 under some
conditions
- task B: replace fd 0 with a malicious library
- task A: attach to task B with PTRACE_ATTACH
- task B: execve() a file with an SMACK64EXEC extended attribute
- task A: while task B is still in the middle of execve(), exit (which
destroys the ptrace relationship)
Make sure that if any flags other than LSM_UNSAFE_PTRACE are set in
bprm->unsafe, we reject the execve().
Cc: stable@vger.kernel.org
Fixes:
5663884caab1 ("Smack: unify all ptrace accesses in the smack")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 27 Sep 2019 01:24:43 +0000 (18:24 -0700)]
sch_cbq: validate TCA_CBQ_WRROPT to avoid crash
[ Upstream commit
e9789c7cc182484fc031fd88097eb14cb26c4596 ]
syzbot reported a crash in cbq_normalize_quanta() caused
by an out of range cl->priority.
iproute2 enforces this check, but malicious users do not.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN PTI
Modules linked in:
CPU: 1 PID: 26447 Comm: syz-executor.1 Not tainted 5.3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:cbq_normalize_quanta.part.0+0x1fd/0x430 net/sched/sch_cbq.c:902
RSP: 0018:
ffff8801a5c333b0 EFLAGS:
00010206
RAX:
0000000020000003 RBX:
00000000fffffff8 RCX:
ffffc9000712f000
RDX:
00000000000043bf RSI:
ffffffff83be8962 RDI:
0000000100000018
RBP:
ffff8801a5c33420 R08:
000000000000003a R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
00000000000002ef
R13:
ffff88018da95188 R14:
dffffc0000000000 R15:
0000000000000015
FS:
00007f37d26b1700(0000) GS:
ffff8801dad00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000004c7cec CR3:
00000001bcd0a006 CR4:
00000000001626f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
[<
ffffffff83be9d57>] cbq_normalize_quanta include/net/pkt_sched.h:27 [inline]
[<
ffffffff83be9d57>] cbq_addprio net/sched/sch_cbq.c:1097 [inline]
[<
ffffffff83be9d57>] cbq_set_wrr+0x2d7/0x450 net/sched/sch_cbq.c:1115
[<
ffffffff83bee8a7>] cbq_change_class+0x987/0x225b net/sched/sch_cbq.c:1537
[<
ffffffff83b96985>] tc_ctl_tclass+0x555/0xcd0 net/sched/sch_api.c:2329
[<
ffffffff83a84655>] rtnetlink_rcv_msg+0x485/0xc10 net/core/rtnetlink.c:5248
[<
ffffffff83cadf0a>] netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2510
[<
ffffffff83a7db6d>] rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5266
[<
ffffffff83cac2c6>] netlink_unicast_kernel net/netlink/af_netlink.c:1324 [inline]
[<
ffffffff83cac2c6>] netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1350
[<
ffffffff83cacd4a>] netlink_sendmsg+0x89a/0xd50 net/netlink/af_netlink.c:1939
[<
ffffffff8399d46e>] sock_sendmsg_nosec net/socket.c:673 [inline]
[<
ffffffff8399d46e>] sock_sendmsg+0x12e/0x170 net/socket.c:684
[<
ffffffff8399f1fd>] ___sys_sendmsg+0x81d/0x960 net/socket.c:2359
[<
ffffffff839a2d05>] __sys_sendmsg+0x105/0x1d0 net/socket.c:2397
[<
ffffffff839a2df9>] SYSC_sendmsg net/socket.c:2406 [inline]
[<
ffffffff839a2df9>] SyS_sendmsg+0x29/0x30 net/socket.c:2404
[<
ffffffff8101ccc8>] do_syscall_64+0x528/0x770 arch/x86/entry/common.c:305
[<
ffffffff84400091>] entry_SYSCALL_64_after_hwframe+0x42/0xb7
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dotan Barak [Tue, 1 Oct 2019 17:21:02 +0000 (10:21 -0700)]
net/rds: Fix error handling in rds_ib_add_one()
[ Upstream commit
d64bf89a75b65f83f06be9fb8f978e60d53752db ]
rds_ibdev:ipaddr_list and rds_ibdev:conn_list are initialized
after allocation some resources such as protection domain.
If allocation of such resources fail, then these uninitialized
variables are accessed in rds_ib_dev_free() in failure path. This
can potentially crash the system. The code has been updated to
initialize these variables very early in the function.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Sudhakar Dindukurti <sudhakar.dindukurti@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dongli Zhang [Tue, 1 Oct 2019 13:56:41 +0000 (21:56 +0800)]
xen-netfront: do not use ~0U as error return value for xennet_fill_frags()
[ Upstream commit
a761129e3625688310aecf26e1be9e98e85f8eb5 ]
xennet_fill_frags() uses ~0U as return value when the sk_buff is not able
to cache extra fragments. This is incorrect because the return type of
xennet_fill_frags() is RING_IDX and 0xffffffff is an expected value for
ring buffer index.
In the situation when the rsp_cons is approaching 0xffffffff, the return
value of xennet_fill_frags() may become 0xffffffff which xennet_poll() (the
caller) would regard as error. As a result, queue->rx.rsp_cons is set
incorrectly because it is updated only when there is error. If there is no
error, xennet_poll() would be responsible to update queue->rx.rsp_cons.
Finally, queue->rx.rsp_cons would point to the rx ring buffer entries whose
queue->rx_skbs[i] and queue->grant_rx_ref[i] are already cleared to NULL.
This leads to NULL pointer access in the next iteration to process rx ring
buffer entries.
The symptom is similar to the one fixed in
commit
00b368502d18 ("xen-netfront: do not assume sk_buff_head list is
empty in error handling").
This patch changes the return type of xennet_fill_frags() to indicate
whether it is successful or failed. The queue->rx.rsp_cons will be
always updated inside this function.
Fixes:
ad4f15dc2c70 ("xen/netfront: don't bug in case of too many frags")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 4 Oct 2019 17:34:45 +0000 (10:34 -0700)]
sch_dsmark: fix potential NULL deref in dsmark_init()
[ Upstream commit
474f0813a3002cb299bb73a5a93aa1f537a80ca8 ]
Make sure TCA_DSMARK_INDICES was provided by the user.
syzbot reported :
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 8799 Comm: syz-executor235 Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:nla_get_u16 include/net/netlink.h:1501 [inline]
RIP: 0010:dsmark_init net/sched/sch_dsmark.c:364 [inline]
RIP: 0010:dsmark_init+0x193/0x640 net/sched/sch_dsmark.c:339
Code: 85 db 58 0f 88 7d 03 00 00 e8 e9 1a ac fb 48 8b 9d 70 ff ff ff 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 04 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 01 38 d0 7c 08 84 d2 0f 85 ca
RSP: 0018:
ffff88809426f3b8 EFLAGS:
00010247
RAX:
dffffc0000000000 RBX:
0000000000000000 RCX:
ffffffff85c6eb09
RDX:
0000000000000000 RSI:
ffffffff85c6eb17 RDI:
0000000000000004
RBP:
ffff88809426f4b0 R08:
ffff88808c4085c0 R09:
ffffed1015d26159
R10:
ffffed1015d26158 R11:
ffff8880ae930ac7 R12:
ffff8880a7e96940
R13:
dffffc0000000000 R14:
ffff88809426f8c0 R15:
0000000000000000
FS:
0000000001292880(0000) GS:
ffff8880ae900000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000020000080 CR3:
000000008ca1b000 CR4:
00000000001406e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
qdisc_create+0x4ee/0x1210 net/sched/sch_api.c:1237
tc_modify_qdisc+0x524/0x1c50 net/sched/sch_api.c:1653
rtnetlink_rcv_msg+0x463/0xb00 net/core/rtnetlink.c:5223
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5241
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0x531/0x710 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x8a5/0xd60 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:657
___sys_sendmsg+0x803/0x920 net/socket.c:2311
__sys_sendmsg+0x105/0x1d0 net/socket.c:2356
__do_sys_sendmsg net/socket.c:2365 [inline]
__se_sys_sendmsg net/socket.c:2363 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2363
do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440369
Fixes:
758cc43c6d73 ("[PKT_SCHED]: Fix dsmark to apply changes consistent")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 4 Oct 2019 18:08:34 +0000 (11:08 -0700)]
nfc: fix memory leak in llcp_sock_bind()
[ Upstream commit
a0c2dc1fe63e2869b74c1c7f6a81d1745c8a695d ]
sysbot reported a memory leak after a bind() has failed.
While we are at it, abort the operation if kmemdup() has failed.
BUG: memory leak
unreferenced object 0xffff888105d83ec0 (size 32):
comm "syz-executor067", pid 7207, jiffies
4294956228 (age 19.430s)
hex dump (first 32 bytes):
00 69 6c 65 20 72 65 61 64 00 6e 65 74 3a 5b 34 .ile read.net:[4
30 32 36 35 33 33 30 39 37 5d 00 00 00 00 00 00
026533097]......
backtrace:
[<
0000000036bac473>] kmemleak_alloc_recursive /./include/linux/kmemleak.h:43 [inline]
[<
0000000036bac473>] slab_post_alloc_hook /mm/slab.h:522 [inline]
[<
0000000036bac473>] slab_alloc /mm/slab.c:3319 [inline]
[<
0000000036bac473>] __do_kmalloc /mm/slab.c:3653 [inline]
[<
0000000036bac473>] __kmalloc_track_caller+0x169/0x2d0 /mm/slab.c:3670
[<
000000000cd39d07>] kmemdup+0x27/0x60 /mm/util.c:120
[<
000000008e57e5fc>] kmemdup /./include/linux/string.h:432 [inline]
[<
000000008e57e5fc>] llcp_sock_bind+0x1b3/0x230 /net/nfc/llcp_sock.c:107
[<
000000009cb0b5d3>] __sys_bind+0x11c/0x140 /net/socket.c:1647
[<
00000000492c3bbc>] __do_sys_bind /net/socket.c:1658 [inline]
[<
00000000492c3bbc>] __se_sys_bind /net/socket.c:1656 [inline]
[<
00000000492c3bbc>] __x64_sys_bind+0x1e/0x30 /net/socket.c:1656
[<
0000000008704b2a>] do_syscall_64+0x76/0x1a0 /arch/x86/entry/common.c:296
[<
000000009f4c57a4>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
30cc4587659e ("NFC: Move LLCP code to the NFC top level diirectory")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Navid Emamdoost [Fri, 4 Oct 2019 20:24:39 +0000 (15:24 -0500)]
net: qlogic: Fix memory leak in ql_alloc_large_buffers
[ Upstream commit
1acb8f2a7a9f10543868ddd737e37424d5c36cf4 ]
In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.
Fixes:
0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Abeni [Fri, 4 Oct 2019 13:11:17 +0000 (15:11 +0200)]
net: ipv4: avoid mixed n_redirects and rate_tokens usage
[ Upstream commit
b406472b5ad79ede8d10077f0c8f05505ace8b6d ]
Since commit
c09551c6ff7f ("net: ipv4: use a dedicated counter
for icmp_v4 redirect packets") we use 'n_redirects' to account
for redirect packets, but we still use 'rate_tokens' to compute
the redirect packets exponential backoff.
If the device sent to the relevant peer any ICMP error packet
after sending a redirect, it will also update 'rate_token' according
to the leaking bucket schema; typically 'rate_token' will raise
above BITS_PER_LONG and the redirect packets backoff algorithm
will produce undefined behavior.
Fix the issue using 'n_redirects' to compute the exponential backoff
in ip_rt_send_redirect().
Note that we still clear rate_tokens after a redirect silence period,
to avoid changing an established behaviour.
The root cause predates git history; before the mentioned commit in
the critical scenario, the kernel stopped sending redirects, after
the mentioned commit the behavior more randomic.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Fixes:
c09551c6ff7f ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Wed, 2 Oct 2019 16:38:55 +0000 (09:38 -0700)]
ipv6: drop incoming packets having a v4mapped source address
[ Upstream commit
6af1799aaf3f1bc8defedddfa00df3192445bbf3 ]
This began with a syzbot report. syzkaller was injecting
IPv6 TCP SYN packets having a v4mapped source address.
After an unsuccessful 4-tuple lookup, TCP creates a request
socket (SYN_RECV) and calls reqsk_queue_hash_req()
reqsk_queue_hash_req() calls sk_ehashfn(sk)
At this point we have AF_INET6 sockets, and the heuristic
used by sk_ehashfn() to either hash the IPv4 or IPv6 addresses
is to use ipv6_addr_v4mapped(&sk->sk_v6_daddr)
For the particular spoofed packet, we end up hashing V4 addresses
which were not initialized by the TCP IPv6 stack, so KMSAN fired
a warning.
I first fixed sk_ehashfn() to test both source and destination addresses,
but then faced various problems, including user-space programs
like packetdrill that had similar assumptions.
Instead of trying to fix the whole ecosystem, it is better
to admit that we have a dual stack behavior, and that we
can not build linux kernels without V4 stack anyway.
The dual stack API automatically forces the traffic to be IPv4
if v4mapped addresses are used at bind() or connect(), so it makes
no sense to allow IPv6 traffic to use the same v4mapped class.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 30 Sep 2019 15:12:41 +0000 (17:12 +0200)]
hso: fix NULL-deref on tty open
[ Upstream commit
8353da9fa69722b54cba82b2ec740afd3d438748 ]
Fix NULL-pointer dereference on tty open due to a failure to handle a
missing interrupt-in endpoint when probing modem ports:
BUG: kernel NULL pointer dereference, address:
0000000000000006
...
RIP: 0010:tiocmget_submit_urb+0x1c/0xe0 [hso]
...
Call Trace:
hso_start_serial_device+0xdc/0x140 [hso]
hso_serial_open+0x118/0x1b0 [hso]
tty_open+0xf1/0x490
Fixes:
542f54823614 ("tty: Modem functions for the HSO driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martijn Coenen [Fri, 16 Feb 2018 08:47:15 +0000 (09:47 +0100)]
ANDROID: binder: synchronize_rcu() when using POLLFREE.
commit
5eeb2ca02a2f6084fc57ae5c244a38baab07033a upstream.
To prevent races with ep_remove_waitqueue() removing the
waitqueue at the same time.
Reported-by: syzbot+a2a3c4909716e271487e@syzkaller.appspotmail.com
Signed-off-by: Martijn Coenen <maco@android.com>
Cc: stable <stable@vger.kernel.org> # 4.14+
Signed-off-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martijn Coenen [Fri, 5 Jan 2018 10:27:07 +0000 (11:27 +0100)]
ANDROID: binder: remove waitqueue when thread exits.
commit
f5cb779ba16334b45ba8946d6bfa6d9834d1527f upstream.
binder_poll() passes the thread->wait waitqueue that
can be slept on for work. When a thread that uses
epoll explicitly exits using BINDER_THREAD_EXIT,
the waitqueue is freed, but it is never removed
from the corresponding epoll data structure. When
the process subsequently exits, the epoll cleanup
code tries to access the waitlist, which results in
a use-after-free.
Prevent this by using POLLFREE when the thread exits.
Signed-off-by: Martijn Coenen <maco@android.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable <stable@vger.kernel.org> # 4.14
[backport BINDER_LOOPER_STATE_POLL logic as well]
Signed-off-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Boichat [Mon, 23 Sep 2019 22:33:55 +0000 (15:33 -0700)]
kmemleak: increase DEBUG_KMEMLEAK_EARLY_LOG_SIZE default to 16K
[ Upstream commit
b751c52bb587ae66f773b15204ef7a147467f4c7 ]
The current default value (400) is too low on many systems (e.g. some
ARM64 platform takes up 1000+ entries).
syzbot uses 16000 as default value, and has proved to be enough on beefy
configurations, so let's pick that value.
This consumes more RAM on boot (each entry is 160 bytes, so in total
~2.5MB of RAM), but the memory would later be freed (early_log is
__initdata).
Link: http://lkml.kernel.org/r/20190730154027.101525-1-drinkcat@chromium.org
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Suggested-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Changwei Ge [Mon, 23 Sep 2019 22:33:37 +0000 (15:33 -0700)]
ocfs2: wait for recovering done after direct unlock request
[ Upstream commit
0a3775e4f883912944481cf2ef36eb6383a9cc74 ]
There is a scenario causing ocfs2 umount hang when multiple hosts are
rebooting at the same time.
NODE1 NODE2 NODE3
send unlock requset to NODE2
dies
become recovery master
recover NODE2
find NODE2 dead
mark resource RECOVERING
directly remove lock from grant list
calculate usage but RECOVERING marked
**miss the window of purging
clear RECOVERING
To reproduce this issue, crash a host and then umount ocfs2
from another node.
To solve this, just let unlock progress wait for recovery done.
Link: http://lkml.kernel.org/r/1550124866-20367-1-git-send-email-gechangwei@live.cn
Signed-off-by: Changwei Ge <gechangwei@live.cn>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
David Howells [Thu, 21 Mar 2019 10:08:08 +0000 (10:08 +0000)]
hypfs: Fix error number left in struct pointer member
[ Upstream commit
b54c64f7adeb241423cd46598f458b5486b0375e ]
In hypfs_fill_super(), if hypfs_create_update_file() fails,
sbi->update_file is left holding an error number. This is passed to
hypfs_kill_super() which doesn't check for this.
Fix this by not setting sbi->update_value until after we've checked for
error.
Fixes:
24bbb1faf3f0 ("[PATCH] s390_hypfs filesystem")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
cc: Heiko Carstens <heiko.carstens@de.ibm.com>
cc: linux-s390@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
OGAWA Hirofumi [Mon, 23 Sep 2019 22:32:53 +0000 (15:32 -0700)]
fat: work around race with userspace's read via blockdev while mounting
[ Upstream commit
07bfa4415ab607e459b69bd86aa7e7602ce10b4f ]
If userspace reads the buffer via blockdev while mounting,
sb_getblk()+modify can race with buffer read via blockdev.
For example,
FS userspace
bh = sb_getblk()
modify bh->b_data
read
ll_rw_block(bh)
fill bh->b_data by on-disk data
/* lost modified data by FS */
set_buffer_uptodate(bh)
set_buffer_uptodate(bh)
Userspace should not use the blockdev while mounting though, the udev
seems to be already doing this. Although I think the udev should try to
avoid this, workaround the race by small overhead.
Link: http://lkml.kernel.org/r/87pnk7l3sw.fsf_-_@mail.parknet.co.jp
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jia-Ju Bai [Tue, 23 Jul 2019 10:00:15 +0000 (18:00 +0800)]
security: smack: Fix possible null-pointer dereferences in smack_socket_sock_rcv_skb()
[ Upstream commit
3f4287e7d98a2954f20bf96c567fdffcd2b63eb9 ]
In smack_socket_sock_rcv_skb(), there is an if statement
on line 3920 to check whether skb is NULL:
if (skb && skb->secmark != 0)
This check indicates skb can be NULL in some cases.
But on lines 3931 and 3932, skb is used:
ad.a.u.net->netif = skb->skb_iif;
ipv6_skb_to_auditdata(skb, &ad.a, NULL);
Thus, possible null-pointer dereferences may occur when skb is NULL.
To fix these possible bugs, an if statement is added to check skb.
These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Joao Moreno [Tue, 3 Sep 2019 14:46:32 +0000 (16:46 +0200)]
HID: apple: Fix stuck function keys when using FN
[ Upstream commit
aec256d0ecd561036f188dbc8fa7924c47a9edfd ]
This fixes an issue in which key down events for function keys would be
repeatedly emitted even after the user has raised the physical key. For
example, the driver fails to emit the F5 key up event when going through
the following steps:
- fnmode=1: hold FN, hold F5, release FN, release F5
- fnmode=2: hold F5, hold FN, release F5, release FN
The repeated F5 key down events can be easily verified using xev.
Signed-off-by: Joao Moreno <mail@joaomoreno.com>
Co-developed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Will Deacon [Thu, 8 Aug 2019 15:51:00 +0000 (16:51 +0100)]
ARM: 8898/1: mm: Don't treat faults reported from cache maintenance as writes
[ Upstream commit
834020366da9ab3fb87d1eb9a3160eb22dbed63a ]
Translation faults arising from cache maintenance instructions are
rather unhelpfully reported with an FSR value where the WnR field is set
to 1, indicating that the faulting access was a write. Since cache
maintenance instructions on 32-bit ARM do not require any particular
permissions, this can cause our private 'cacheflush' system call to fail
spuriously if a translation fault is generated due to page aging when
targetting a read-only VMA.
In this situation, we will return -EFAULT to userspace, although this is
unfortunately suppressed by the popular '__builtin___clear_cache()'
intrinsic provided by GCC, which returns void.
Although it's tempting to write this off as a userspace issue, we can
actually do a little bit better on CPUs that support LPAE, even if the
short-descriptor format is in use. On these CPUs, cache maintenance
faults additionally set the CM field in the FSR, which we can use to
suppress the write permission checks in the page fault handler and
succeed in performing cache maintenance to read-only areas even in the
presence of a translation fault.
Reported-by: Orion Hodson <oth@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kai-Heng Feng [Fri, 5 Jul 2019 04:55:03 +0000 (12:55 +0800)]
mfd: intel-lpss: Remove D3cold delay
[ Upstream commit
76380a607ba0b28627c9b4b55cd47a079a59624b ]
Goodix touchpad may drop its first couple input events when
i2c-designware-platdrv and intel-lpss it connects to took too long to
runtime resume from runtime suspended state.
This issue happens becuase the touchpad has a rather small buffer to
store up to 13 input events, so if the host doesn't read those events in
time (i.e. runtime resume takes too long), events are dropped from the
touchpad's buffer.
The bottleneck is D3cold delay it waits when transitioning from D3cold
to D0, hence remove the delay to make the resume faster. I've tested
some systems with intel-lpss and haven't seen any regression.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202683
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Thu, 1 Aug 2019 22:38:14 +0000 (15:38 -0700)]
scsi: core: Reduce memory required for SCSI logging
[ Upstream commit
dccc96abfb21dc19d69e707c38c8ba439bba7160 ]
The data structure used for log messages is so large that it can cause a
boot failure. Since allocations from that data structure can fail anyway,
use kmalloc() / kfree() instead of that data structure.
See also https://bugzilla.kernel.org/show_bug.cgi?id=204119.
See also commit
ded85c193a39 ("scsi: Implement per-cpu logging buffer") # v4.0.
Reported-by: Jan Palus <jpalus@fastmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jan Palus <jpalus@fastmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Lynch [Tue, 10 Sep 2019 22:52:44 +0000 (17:52 -0500)]
powerpc/pseries: correctly track irq state in default idle
[ Upstream commit
92c94dfb69e350471473fd3075c74bc68150879e ]
prep_irq_for_idle() is intended to be called before entering
H_CEDE (and it is used by the pseries cpuidle driver). However the
default pseries idle routine does not call it, leading to mismanaged
lazy irq state when the cpuidle driver isn't in use. Manifestations of
this include:
* Dropped IPIs in the time immediately after a cpu comes
online (before it has installed the cpuidle handler), making the
online operation block indefinitely waiting for the new cpu to
respond.
* Hitting this WARN_ON in arch_local_irq_restore():
/*
* We should already be hard disabled here. We had bugs
* where that wasn't the case so let's dbl check it and
* warn if we are wrong. Only do that when IRQ tracing
* is enabled as mfmsr() can be costly.
*/
if (WARN_ON_ONCE(mfmsr() & MSR_EE))
__hard_irq_disable();
Call prep_irq_for_idle() from pseries_lpar_idle() and honor its
result.
Fixes:
363edbe2614a ("powerpc: Default arch idle could cede processor on pseries")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190910225244.25056-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicholas Piggin [Fri, 2 Aug 2019 10:56:32 +0000 (20:56 +1000)]
powerpc/64s/exception: machine check use correct cfar for late handler
[ Upstream commit
0b66370c61fcf5fcc1d6901013e110284da6e2bb ]
Bare metal machine checks run an "early" handler in real mode before
running the main handler which reports the event.
The main handler runs exactly as a normal interrupt handler, after the
"windup" which sets registers back as they were at interrupt entry.
CFAR does not get restored by the windup code, so that will be wrong
when the handler is run.
Restore the CFAR to the saved value before running the late handler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802105709.27696-8-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
hexin [Thu, 22 Aug 2019 03:35:19 +0000 (11:35 +0800)]
vfio_pci: Restore original state on release
[ Upstream commit
92c8026854c25093946e0d7fe536fd9eac440f06 ]
vfio_pci_enable() saves the device's initial configuration information
with the intent that it is restored in vfio_pci_disable(). However,
the commit referenced in Fixes: below replaced the call to
__pci_reset_function_locked(), which is not wrapped in a state save
and restore, with pci_try_reset_function(), which overwrites the
restored device state with the current state before applying it to the
device. Reinstate use of __pci_reset_function_locked() to return to
the desired behavior.
Fixes:
890ed578df82 ("vfio-pci: Use pci "try" reset interface")
Signed-off-by: hexin <hexin15@baidu.com>
Signed-off-by: Liu Qi <liuqi16@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sowjanya Komatineni [Fri, 16 Aug 2019 19:41:46 +0000 (12:41 -0700)]
pinctrl: tegra: Fix write barrier placement in pmx_writel
[ Upstream commit
c2cf351eba2ff6002ce8eb178452219d2521e38e ]
pmx_writel uses writel which inserts write barrier before the
register write.
This patch has fix to replace writel with writel_relaxed followed
by a readback and memory barrier to ensure write operation is
completed for successful pinctrl change.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1565984527-5272-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Lynch [Fri, 2 Aug 2019 19:29:26 +0000 (14:29 -0500)]
powerpc/pseries/mobility: use cond_resched when updating device tree
[ Upstream commit
ccfb5bd71d3d1228090a8633800ae7cdf42a94ac ]
After a partition migration, pseries_devicetree_update() processes
changes to the device tree communicated from the platform to
Linux. This is a relatively heavyweight operation, with multiple
device tree searches, memory allocations, and conversations with
partition firmware.
There's a few levels of nested loops which are bounded only by
decisions made by the platform, outside of Linux's control, and indeed
we have seen RCU stalls on large systems while executing this call
graph. Use cond_resched() in these loops so that the cpu is yielded
when needed.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802192926.19277-4-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe Leroy [Wed, 14 Aug 2019 09:25:52 +0000 (09:25 +0000)]
powerpc/futex: Fix warning: 'oldval' may be used uninitialized in this function
[ Upstream commit
38a0d0cdb46d3f91534e5b9839ec2d67be14c59d ]
We see warnings such as:
kernel/futex.c: In function 'do_futex':
kernel/futex.c:1676:17: warning: 'oldval' may be used uninitialized in this function [-Wmaybe-uninitialized]
return oldval == cmparg;
^
kernel/futex.c:1651:6: note: 'oldval' was declared here
int oldval, ret;
^
This is because arch_futex_atomic_op_inuser() only sets *oval if ret
is 0 and GCC doesn't see that it will only use it when ret is 0.
Anyway, the non-zero ret path is an error path that won't suffer from
setting *oval, and as *oval is a local var in futex_atomic_op_inuser()
it will have no impact.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: reword change log slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/86b72f0c134367b214910b27b9a6dd3321af93bb.1565774657.git.christophe.leroy@c-s.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Lynch [Fri, 2 Aug 2019 19:29:24 +0000 (14:29 -0500)]
powerpc/rtas: use device model APIs and serialization during LPM
[ Upstream commit
a6717c01ddc259f6f73364779df058e2c67309f8 ]
The LPAR migration implementation and userspace-initiated cpu hotplug
can interleave their executions like so:
1. Set cpu 7 offline via sysfs.
2. Begin a partition migration, whose implementation requires the OS
to ensure all present cpus are online; cpu 7 is onlined:
rtas_ibm_suspend_me -> rtas_online_cpus_mask -> cpu_up
This sets cpu 7 online in all respects except for the cpu's
corresponding struct device; dev->offline remains true.
3. Set cpu 7 online via sysfs. _cpu_up() determines that cpu 7 is
already online and returns success. The driver core (device_online)
sets dev->offline = false.
4. The migration completes and restores cpu 7 to offline state:
rtas_ibm_suspend_me -> rtas_offline_cpus_mask -> cpu_down
This leaves cpu7 in a state where the driver core considers the cpu
device online, but in all other respects it is offline and
unused. Attempts to online the cpu via sysfs appear to succeed but the
driver core actually does not pass the request to the lower-level
cpuhp support code. This makes the cpu unusable until the cpu device
is manually set offline and then online again via sysfs.
Instead of directly calling cpu_up/cpu_down, the migration code should
use the higher-level device core APIs to maintain consistent state and
serialize operations.
Fixes:
120496ac2d2d ("powerpc: Bring all threads online prior to migration/hibernation")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190802192926.19277-2-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stephen Boyd [Wed, 31 Jul 2019 19:35:13 +0000 (12:35 -0700)]
clk: sirf: Don't reference clk_init_data after registration
[ Upstream commit
af55dadfbce35b4f4c6247244ce3e44b2e242b84 ]
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Guo Zeng <Guo.Zeng@csr.com>
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-6-sboyd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Huckleberry [Thu, 27 Jun 2019 22:06:42 +0000 (15:06 -0700)]
clk: qoriq: Fix -Wunused-const-variable
[ Upstream commit
a95fb581b144b5e73da382eaedb2e32027610597 ]
drivers/clk/clk-qoriq.c:138:38: warning: unused variable
'p5020_cmux_grp1' [-Wunused-const-variable] static const struct
clockgen_muxinfo p5020_cmux_grp1
drivers/clk/clk-qoriq.c:146:38: warning: unused variable
'p5020_cmux_grp2' [-Wunused-const-variable] static const struct
clockgen_muxinfo p5020_cmux_grp2
In the definition of the p5020 chip, the p2041 chip's info was used
instead. The p5020 and p2041 chips have different info. This is most
likely a typo.
Link: https://github.com/ClangBuiltLinux/linux/issues/525
Cc: clang-built-linux@googlegroups.com
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Link: https://lkml.kernel.org/r/20190627220642.78575-1-nhuck@google.com
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Corey Minyard [Fri, 2 Aug 2019 12:31:36 +0000 (07:31 -0500)]
ipmi_si: Only schedule continuously in the thread in maintenance mode
[ Upstream commit
340ff31ab00bca5c15915e70ad9ada3030c98cf8 ]
ipmi_thread() uses back-to-back schedule() to poll for command
completion which, on some machines, can push up CPU consumption and
heavily tax the scheduler locks leading to noticeable overall
performance degradation.
This was originally added so firmware updates through IPMI would
complete in a timely manner. But we can't kill the scheduler
locks for that one use case.
Instead, only run schedule() continuously in maintenance mode,
where firmware updates should run.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jia-Ju Bai [Mon, 29 Jul 2019 08:36:44 +0000 (16:36 +0800)]
gpu: drm: radeon: Fix a possible null-pointer dereference in radeon_connector_set_property()
[ Upstream commit
f3eb9b8f67bc28783eddc142ad805ebdc53d6339 ]
In radeon_connector_set_property(), there is an if statement on line 743
to check whether connector->encoder is NULL:
if (connector->encoder)
When connector->encoder is NULL, it is used on line 755:
if (connector->encoder->crtc)
Thus, a possible null-pointer dereference may occur.
To fix this bug, connector->encoder is checked before being used.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marko Kohtala [Tue, 18 Jun 2019 07:41:08 +0000 (10:41 +0300)]
video: ssd1307fb: Start page range at page_offset
[ Upstream commit
dd9782834dd9dde3624ff1acea8859f3d3e792d4 ]
The page_offset was only applied to the end of the page range. This caused
the display updates to cause a scrolling effect on the display because the
amount of data written to the display did not match the range display
expected.
Fixes:
301bc0675b67 ("video: ssd1307fb: Make use of horizontal addressing mode")
Signed-off-by: Marko Kohtala <marko.kohtala@okoko.fi>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618074111.9309-4-marko.kohtala@okoko.fi
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Sat, 5 Oct 2019 10:27:56 +0000 (12:27 +0200)]
Linux 4.4.195
Filipe Manana [Tue, 24 Sep 2019 09:49:54 +0000 (10:49 +0100)]
Btrfs: fix race setting up and completing qgroup rescan workers
[ Upstream commit
13fc1d271a2e3ab8a02071e711add01fab9271f6 ]
There is a race between setting up a qgroup rescan worker and completing
a qgroup rescan worker that can lead to callers of the qgroup rescan wait
ioctl to either not wait for the rescan worker to complete or to hang
forever due to missing wake ups. The following diagram shows a sequence
of steps that illustrates the race.
CPU 1 CPU 2 CPU 3
btrfs_ioctl_quota_rescan()
btrfs_qgroup_rescan()
qgroup_rescan_init()
mutex_lock(&fs_info->qgroup_rescan_lock)
spin_lock(&fs_info->qgroup_lock)
fs_info->qgroup_flags |=
BTRFS_QGROUP_STATUS_FLAG_RESCAN
init_completion(
&fs_info->qgroup_rescan_completion)
fs_info->qgroup_rescan_running = true
mutex_unlock(&fs_info->qgroup_rescan_lock)
spin_unlock(&fs_info->qgroup_lock)
btrfs_init_work()
--> starts the worker
btrfs_qgroup_rescan_worker()
mutex_lock(&fs_info->qgroup_rescan_lock)
fs_info->qgroup_flags &=
~BTRFS_QGROUP_STATUS_FLAG_RESCAN
mutex_unlock(&fs_info->qgroup_rescan_lock)
starts transaction, updates qgroup status
item, etc
btrfs_ioctl_quota_rescan()
btrfs_qgroup_rescan()
qgroup_rescan_init()
mutex_lock(&fs_info->qgroup_rescan_lock)
spin_lock(&fs_info->qgroup_lock)
fs_info->qgroup_flags |=
BTRFS_QGROUP_STATUS_FLAG_RESCAN
init_completion(
&fs_info->qgroup_rescan_completion)
fs_info->qgroup_rescan_running = true
mutex_unlock(&fs_info->qgroup_rescan_lock)
spin_unlock(&fs_info->qgroup_lock)
btrfs_init_work()
--> starts another worker
mutex_lock(&fs_info->qgroup_rescan_lock)
fs_info->qgroup_rescan_running = false
mutex_unlock(&fs_info->qgroup_rescan_lock)
complete_all(&fs_info->qgroup_rescan_completion)
Before the rescan worker started by the task at CPU 3 completes, if
another task calls btrfs_ioctl_quota_rescan(), it will get -EINPROGRESS
because the flag BTRFS_QGROUP_STATUS_FLAG_RESCAN is set at
fs_info->qgroup_flags, which is expected and correct behaviour.
However if other task calls btrfs_ioctl_quota_rescan_wait() before the
rescan worker started by the task at CPU 3 completes, it will return
immediately without waiting for the new rescan worker to complete,
because fs_info->qgroup_rescan_running is set to false by CPU 2.
This race is making test case btrfs/171 (from fstests) to fail often:
btrfs/171 9s ... - output mismatch (see /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad)
# --- tests/btrfs/171.out 2018-09-16 21:30:48.
505104287 +0100
# +++ /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad 2019-09-19 02:01:36.
938486039 +0100
# @@ -1,2 +1,3 @@
# QA output created by 171
# +ERROR: quota rescan failed: Operation now in progress
# Silence is golden
# ...
# (Run 'diff -u /home/fdmanana/git/hub/xfstests/tests/btrfs/171.out /home/fdmanana/git/hub/xfstests/results//btrfs/171.out.bad' to see the entire diff)
That is because the test calls the btrfs-progs commands "qgroup quota
rescan -w", "qgroup assign" and "qgroup remove" in a sequence that makes
calls to the rescan start ioctl fail with -EINPROGRESS (note the "btrfs"
commands 'qgroup assign' and 'qgroup remove' often call the rescan start
ioctl after calling the qgroup assign ioctl,
btrfs_ioctl_qgroup_assign()), since previous waits didn't actually wait
for a rescan worker to complete.
Another problem the race can cause is missing wake ups for waiters,
since the call to complete_all() happens outside a critical section and
after clearing the flag BTRFS_QGROUP_STATUS_FLAG_RESCAN. In the sequence
diagram above, if we have a waiter for the first rescan task (executed
by CPU 2), then fs_info->qgroup_rescan_completion.wait is not empty, and
if after the rescan worker clears BTRFS_QGROUP_STATUS_FLAG_RESCAN and
before it calls complete_all() against
fs_info->qgroup_rescan_completion, the task at CPU 3 calls
init_completion() against fs_info->qgroup_rescan_completion which
re-initilizes its wait queue to an empty queue, therefore causing the
rescan worker at CPU 2 to call complete_all() against an empty queue,
never waking up the task waiting for that rescan worker.
Fix this by clearing BTRFS_QGROUP_STATUS_FLAG_RESCAN and setting
fs_info->qgroup_rescan_running to false in the same critical section,
delimited by the mutex fs_info->qgroup_rescan_lock, as well as doing the
call to complete_all() in that same critical section. This gives the
protection needed to avoid rescan wait ioctl callers not waiting for a
running rescan worker and the lost wake ups problem, since setting that
rescan flag and boolean as well as initializing the wait queue is done
already in a critical section delimited by that mutex (at
qgroup_rescan_init()).
Fixes:
57254b6ebce4ce ("Btrfs: add ioctl to wait for qgroup rescan completion")
Fixes:
d2c609b834d62f ("btrfs: properly track when rescan worker is running")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikolay Borisov [Wed, 4 Sep 2019 16:33:58 +0000 (19:33 +0300)]
btrfs: Relinquish CPUs in btrfs_compare_trees
commit
6af112b11a4bc1b560f60a618ac9c1dcefe9836e upstream.
When doing any form of incremental send the parent and the child trees
need to be compared via btrfs_compare_trees. This can result in long
loop chains without ever relinquishing the CPU. This causes softlockup
detector to trigger when comparing trees with a lot of items. Example
report:
watchdog: BUG: soft lockup - CPU#0 stuck for 24s! [snapperd:16153]
CPU: 0 PID: 16153 Comm: snapperd Not tainted 5.2.9-1-default #1 openSUSE Tumbleweed (unreleased)
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
pstate:
40000005 (nZcv daif -PAN -UAO)
pc : __ll_sc_arch_atomic_sub_return+0x14/0x20
lr : btrfs_release_extent_buffer_pages+0xe0/0x1e8 [btrfs]
sp :
ffff00001273b7e0
Call trace:
__ll_sc_arch_atomic_sub_return+0x14/0x20
release_extent_buffer+0xdc/0x120 [btrfs]
free_extent_buffer.part.0+0xb0/0x118 [btrfs]
free_extent_buffer+0x24/0x30 [btrfs]
btrfs_release_path+0x4c/0xa0 [btrfs]
btrfs_free_path.part.0+0x20/0x40 [btrfs]
btrfs_free_path+0x24/0x30 [btrfs]
get_inode_info+0xa8/0xf8 [btrfs]
finish_inode_if_needed+0xe0/0x6d8 [btrfs]
changed_cb+0x9c/0x410 [btrfs]
btrfs_compare_trees+0x284/0x648 [btrfs]
send_subvol+0x33c/0x520 [btrfs]
btrfs_ioctl_send+0x8a0/0xaf0 [btrfs]
btrfs_ioctl+0x199c/0x2288 [btrfs]
do_vfs_ioctl+0x4b0/0x820
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_common.constprop.0+0x7c/0x188
el0_svc_handler+0x34/0x90
el0_svc+0x8/0xc
Fix this by adding a call to cond_resched at the beginning of the main
loop in btrfs_compare_trees.
Fixes:
7069830a9e38 ("Btrfs: add btrfs_compare_trees function")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Mon, 12 Aug 2019 18:14:29 +0000 (19:14 +0100)]
Btrfs: fix use-after-free when using the tree modification log
commit
efad8a853ad2057f96664328a0d327a05ce39c76 upstream.
At ctree.c:get_old_root(), we are accessing a root's header owner field
after we have freed the respective extent buffer. This results in an
use-after-free that can lead to crashes, and when CONFIG_DEBUG_PAGEALLOC
is set, results in a stack trace like the following:
[ 3876.799331] stack segment: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[ 3876.799363] CPU: 0 PID: 15436 Comm: pool Not tainted 5.3.0-rc3-btrfs-next-54 #1
[ 3876.799385] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014
[ 3876.799433] RIP: 0010:btrfs_search_old_slot+0x652/0xd80 [btrfs]
(...)
[ 3876.799502] RSP: 0018:
ffff9f08c1a2f9f0 EFLAGS:
00010286
[ 3876.799518] RAX:
ffff8dd300000000 RBX:
ffff8dd85a7a9348 RCX:
000000038da26000
[ 3876.799538] RDX:
0000000000000000 RSI:
ffffe522ce368980 RDI:
0000000000000246
[ 3876.799559] RBP:
dae1922adadad000 R08:
0000000008020000 R09:
ffffe522c0000000
[ 3876.799579] R10:
ffff8dd57fd788c8 R11:
000000007511b030 R12:
ffff8dd781ddc000
[ 3876.799599] R13:
ffff8dd9e6240578 R14:
ffff8dd6896f7a88 R15:
ffff8dd688cf90b8
[ 3876.799620] FS:
00007f23ddd97700(0000) GS:
ffff8dda20200000(0000) knlGS:
0000000000000000
[ 3876.799643] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 3876.799660] CR2:
00007f23d4024000 CR3:
0000000710bb0005 CR4:
00000000003606f0
[ 3876.799682] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 3876.799703] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 3876.799723] Call Trace:
[ 3876.799735] ? do_raw_spin_unlock+0x49/0xc0
[ 3876.799749] ? _raw_spin_unlock+0x24/0x30
[ 3876.799779] resolve_indirect_refs+0x1eb/0xc80 [btrfs]
[ 3876.799810] find_parent_nodes+0x38d/0x1180 [btrfs]
[ 3876.799841] btrfs_check_shared+0x11a/0x1d0 [btrfs]
[ 3876.799870] ? extent_fiemap+0x598/0x6e0 [btrfs]
[ 3876.799895] extent_fiemap+0x598/0x6e0 [btrfs]
[ 3876.799913] do_vfs_ioctl+0x45a/0x700
[ 3876.799926] ksys_ioctl+0x70/0x80
[ 3876.799938] ? trace_hardirqs_off_thunk+0x1a/0x20
[ 3876.799953] __x64_sys_ioctl+0x16/0x20
[ 3876.799965] do_syscall_64+0x62/0x220
[ 3876.799977] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 3876.799993] RIP: 0033:0x7f23e0013dd7
(...)
[ 3876.800056] RSP: 002b:
00007f23ddd96ca8 EFLAGS:
00000246 ORIG_RAX:
0000000000000010
[ 3876.800078] RAX:
ffffffffffffffda RBX:
00007f23d80210f8 RCX:
00007f23e0013dd7
[ 3876.800099] RDX:
00007f23d80210f8 RSI:
00000000c020660b RDI:
0000000000000003
[ 3876.800626] RBP:
000055fa2a2a2440 R08:
0000000000000000 R09:
00007f23ddd96d7c
[ 3876.801143] R10:
00007f23d8022000 R11:
0000000000000246 R12:
00007f23ddd96d80
[ 3876.801662] R13:
00007f23ddd96d78 R14:
00007f23d80210f0 R15:
00007f23ddd96d80
(...)
[ 3876.805107] ---[ end trace
e53161e179ef04f9 ]---
Fix that by saving the root's header owner field into a local variable
before freeing the root's extent buffer, and then use that local variable
when needed.
Fixes:
30b0463a9394d9 ("Btrfs: fix accessing the root pointer in tree mod log functions")
CC: stable@vger.kernel.org # 3.10+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Salyzyn [Thu, 29 Aug 2019 18:30:14 +0000 (11:30 -0700)]
ovl: filter of trusted xattr results in audit
commit
5c2e9f346b815841f9bed6029ebcb06415caf640 upstream.
When filtering xattr list for reading, presence of trusted xattr
results in a security audit log. However, if there is other content
no errno will be set, and if there isn't, the errno will be -ENODATA
and not -EPERM as is usually associated with a lack of capability.
The check does not block the request to list the xattrs present.
Switch to ns_capable_noaudit to reflect a more appropriate check.
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Cc: linux-security-module@vger.kernel.org
Cc: kernel-team@android.com
Cc: stable@vger.kernel.org # v3.18+
Fixes:
a082c6f680da ("ovl: filter trusted xattr for non-admin")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Shilovsky [Thu, 26 Sep 2019 19:31:20 +0000 (12:31 -0700)]
CIFS: Fix oplock handling for SMB 2.1+ protocols
commit
a016e2794fc3a245a91946038dd8f34d65e53cc3 upstream.
There may be situations when a server negotiates SMB 2.1
protocol version or higher but responds to a CREATE request
with an oplock rather than a lease.
Currently the client doesn't handle such a case correctly:
when another CREATE comes in the server sends an oplock
break to the initial CREATE and the client doesn't send
an ack back due to a wrong caching level being set (READ
instead of RWH). Missing an oplock break ack makes the
server wait until the break times out which dramatically
increases the latency of the second CREATE.
Fix this by properly detecting oplocks when using SMB 2.1
protocol version and higher.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Brandt [Thu, 26 Sep 2019 12:19:09 +0000 (07:19 -0500)]
i2c: riic: Clear NACK in tend isr
commit
a71e2ac1f32097fbb2beab098687a7a95c84543e upstream.
The NACKF flag should be cleared in INTRIICNAKI interrupt processing as
description in HW manual.
This issue shows up quickly when PREEMPT_RT is applied and a device is
probed that is not plugged in (like a touchscreen controller). The result
is endless interrupts that halt system boot.
Fixes:
310c18a41450 ("i2c: riic: add driver")
Cc: stable@vger.kernel.org
Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Vivier [Tue, 17 Sep 2019 09:54:50 +0000 (11:54 +0200)]
hwrng: core - don't wait on add_early_randomness()
commit
78887832e76541f77169a24ac238fccb51059b63 upstream.
add_early_randomness() is called by hwrng_register() when the
hardware is added. If this hardware and its module are present
at boot, and if there is no data available the boot hangs until
data are available and can't be interrupted.
For instance, in the case of virtio-rng, in some cases the host can be
not able to provide enough entropy for all the guests.
We can have two easy ways to reproduce the problem but they rely on
misconfiguration of the hypervisor or the egd daemon:
- if virtio-rng device is configured to connect to the egd daemon of the
host but when the virtio-rng driver asks for data the daemon is not
connected,
- if virtio-rng device is configured to connect to the egd daemon of the
host but the egd daemon doesn't provide data.
The guest kernel will hang at boot until the virtio-rng driver provides
enough data.
To avoid that, call rng_get_data() in non-blocking mode (wait=0)
from add_early_randomness().
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Fixes:
d9e797261933 ("hwrng: add randomness to system from rng...")
Cc: <stable@vger.kernel.org>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chao Yu [Wed, 11 Sep 2019 09:36:50 +0000 (17:36 +0800)]
quota: fix wrong condition in is_quota_modification()
commit
6565c182094f69e4ffdece337d395eb7ec760efc upstream.
Quoted from
commit
3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize")
" At LSF we decided that if we truncate up from isize we shouldn't trim
fallocated blocks that were fallocated with KEEP_SIZE and are past the
new i_size. This patch fixes ext4 to do this. "
And generic/092 of fstest have covered this case for long time, however
is_quota_modification() didn't adjust based on that rule, so that in
below condition, we will lose to quota block change:
- fallocate blocks beyond EOF
- remount
- truncate(file_path, file_size)
Fix it.
Link: https://lore.kernel.org/r/20190911093650.35329-1-yuchao0@huawei.com
Fixes:
3da40c7b0898 ("ext4: only call ext4_truncate when size <= isize")
CC: stable@vger.kernel.org
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Sat, 24 Aug 2019 02:38:00 +0000 (22:38 -0400)]
ext4: fix punch hole for inline_data file systems
commit
c1e8220bd316d8ae8e524df39534b8a412a45d5e upstream.
If a program attempts to punch a hole on an inline data file, we need
to convert it to a normal file first.
This was detected using ext4/032 using the adv configuration. Simple
reproducer:
mke2fs -Fq -t ext4 -O inline_data /dev/vdc
mount /vdc
echo "" > /vdc/testfile
xfs_io -c 'truncate
33554432' /vdc/testfile
xfs_io -c 'fpunch 0
1048576' /vdc/testfile
umount /vdc
e2fsck -fy /dev/vdc
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo Handa [Mon, 26 Aug 2019 13:13:25 +0000 (22:13 +0900)]
/dev/mem: Bail out upon SIGKILL.
commit
8619e5bdeee8b2c685d686281f2d2a6017c4bc15 upstream.
syzbot found that a thread can stall for minutes inside read_mem() or
write_mem() after that thread was killed by SIGKILL [1]. Reading from
iomem areas of /dev/mem can be slow, depending on the hardware.
While reading 2GB at one read() is legal, delaying termination of killed
thread for minutes is bad. Thus, allow reading/writing /dev/mem and
/dev/kmem to be preemptible and killable.
[ 1335.912419][T20577] read_mem: sz=4096 count=
2134565632
[ 1335.943194][T20577] read_mem: sz=4096 count=
2134561536
[ 1335.978280][T20577] read_mem: sz=4096 count=
2134557440
[ 1336.011147][T20577] read_mem: sz=4096 count=
2134553344
[ 1336.041897][T20577] read_mem: sz=4096 count=
2134549248
Theoretically, reading/writing /dev/mem and /dev/kmem can become
"interruptible". But this patch chose "killable". Future patch will make
them "interruptible" so that we can revert to "killable" if some program
regressed.
[1] https://syzkaller.appspot.com/bug?id=
a0e3436829698d5824231251fad9d8e998f94f5e
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot <syzbot+8ab2d0f39fb79fe6ca40@syzkaller.appspotmail.com>
Link: https://lore.kernel.org/r/1566825205-10703-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Denis Kenzior [Wed, 28 Aug 2019 21:11:10 +0000 (16:11 -0500)]
cfg80211: Purge frame registrations on iftype change
commit
c1d3ad84eae35414b6b334790048406bd6301b12 upstream.
Currently frame registrations are not purged, even when changing the
interface type. This can lead to potentially weird situations where
frames possibly not allowed on a given interface type remain registered
due to the type switching happening after registration.
The kernel currently relies on userspace apps to actually purge the
registrations themselves, this is not something that the kernel should
rely on.
Add a call to cfg80211_mlme_purge_registrations() to forcefully remove
any registrations left over prior to switching the iftype.
Cc: stable@vger.kernel.org
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190828211110.15005-1-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xiao Ni [Mon, 8 Jul 2019 02:14:32 +0000 (10:14 +0800)]
md/raid6: Set R5_ReadError when there is read failure on parity disk
commit
143f6e733b73051cd22dcb80951c6c929da413ce upstream.
7471fb77ce4d ("md/raid6: Fix anomily when recovering a single device in
RAID6.") avoids rereading P when it can be computed from other members.
However, this misses the chance to re-write the right data to P. This
patch sets R5_ReadError if the re-read fails.
Also, when re-read is skipped, we also missed the chance to reset
rdev->read_errors to 0. It can fail the disk when there are many read
errors on P member disk (other disks don't have read error)
V2: upper layer read request don't read parity/Q data. So there is no
need to consider such situation.
This is Reported-by: kbuild test robot <lkp@intel.com>
Fixes:
7471fb77ce4d ("md/raid6: Fix anomily when recovering a single device in RAID6.")
Cc: <stable@vger.kernel.org> #4.4+
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thadeu Lima de Souza Cascardo [Tue, 3 Sep 2019 17:18:02 +0000 (14:18 -0300)]
alarmtimer: Use EOPNOTSUPP instead of ENOTSUPP
commit
f18ddc13af981ce3c7b7f26925f099e7c6929aba upstream.
ENOTSUPP is not supposed to be returned to userspace. This was found on an
OpenPower machine, where the RTC does not support set_alarm.
On that system, a clock_nanosleep(CLOCK_REALTIME_ALARM, ...) results in
"524 Unknown error 524"
Replace it with EOPNOTSUPP which results in the expected "95 Operation not
supported" error.
Fixes:
1c6b39ad3f01 (alarmtimers: Return -ENOTSUPP if no RTC device is present)
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190903171802.28314-1-cascardo@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luis Araneda [Thu, 8 Aug 2019 12:52:43 +0000 (08:52 -0400)]
ARM: zynq: Use memcpy_toio instead of memcpy on smp bring-up
commit
b7005d4ef4f3aa2dc24019ffba03a322557ac43d upstream.
This fixes a kernel panic on memcpy when
FORTIFY_SOURCE is enabled.
The initial smp implementation on commit
aa7eb2bb4e4a
("arm: zynq: Add smp support")
used memcpy, which worked fine until commit
ee333554fed5
("ARM: 8749/1: Kconfig: Add ARCH_HAS_FORTIFY_SOURCE")
enabled overflow checks at runtime, producing a read
overflow panic.
The computed size of memcpy args are:
- p_size (dst):
4294967295 = (size_t) -1
- q_size (src): 1
- size (len): 8
Additionally, the memory is marked as __iomem, so one of
the memcpy_* functions should be used for read/write.
Fixes:
aa7eb2bb4e4a ("arm: zynq: Add smp support")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amadeusz Sławiński [Tue, 27 Aug 2019 14:17:08 +0000 (16:17 +0200)]
ASoC: Intel: Fix use of potentially uninitialized variable
commit
810f3b860850148788fc1ed8a6f5f807199fed65 upstream.
If ipc->ops.reply_msg_match is NULL, we may end up using uninitialized
mask value.
reported by smatch:
sound/soc/intel/common/sst-ipc.c:266 sst_ipc_reply_find_msg() error: uninitialized symbol 'mask'.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Link: https://lore.kernel.org/r/20190827141712.21015-3-amadeuszx.slawinski@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Sun, 18 Aug 2019 15:03:23 +0000 (12:03 -0300)]
media: sn9c20x: Add MSI MS-1039 laptop to flip_dmi_table
commit
7e0bb5828311f811309bed5749528ca04992af2f upstream.
Like a bunch of other MSI laptops the MS-1039 uses a 0c45:627b
SN9C201 + OV7660 webcam which is mounted upside down.
Add it to the sn9c20x flip_dmi_table to deal with this.
Cc: stable@vger.kernel.org
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Tue, 3 Sep 2019 23:36:45 +0000 (16:36 -0700)]
KVM: x86: Manually calculate reserved bits when loading PDPTRS
commit
16cfacc8085782dab8e365979356ce1ca87fd6cc upstream.
Manually generate the PDPTR reserved bit mask when explicitly loading
PDPTRs. The reserved bits that are being tracked by the MMU reflect the
current paging mode, which is unlikely to be PAE paging in the vast
majority of flows that use load_pdptrs(), e.g. CR0 and CR4 emulation,
__set_sregs(), etc... This can cause KVM to incorrectly signal a bad
PDPTR, or more likely, miss a reserved bit check and subsequently fail
a VM-Enter due to a bad VMCS.GUEST_PDPTR.
Add a one off helper to generate the reserved bits instead of sharing
code across the MMU's calculations and the PDPTR emulation. The PDPTR
reserved bits are basically set in stone, and pushing a helper into
the MMU's calculation adds unnecessary complexity without improving
readability.
Oppurtunistically fix/update the comment for load_pdptrs().
Note, the buggy commit also introduced a deliberate functional change,
"Also remove bit 5-6 from rsvd_bits_mask per latest SDM.", which was
effectively (and correctly) reverted by commit
cd9ae5fe47df ("KVM: x86:
Fix page-tables reserved bits"). A bit of SDM archaeology shows that
the SDM from late 2008 had a bug (likely a copy+paste error) where it
listed bits 6:5 as AVL and A for PDPTEs used for 4k entries but reserved
for 2mb entries. I.e. the SDM contradicted itself, and bits 6:5 are and
always have been reserved.
Fixes:
20c466b56168d ("KVM: Use rsvd_bits_mask in load_pdptrs()")
Cc: stable@vger.kernel.org
Cc: Nadav Amit <nadav.amit@gmail.com>
Reported-by: Doug Reiland <doug.reiland@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Dakinevich [Tue, 27 Aug 2019 13:07:08 +0000 (13:07 +0000)]
KVM: x86: set ctxt->have_exception in x86_decode_insn()
commit
c8848cee74ff05638e913582a476bde879c968ad upstream.
x86_emulate_instruction() takes into account ctxt->have_exception flag
during instruction decoding, but in practice this flag is never set in
x86_decode_insn().
Fixes:
6ea6e84309ca ("KVM: x86: inject exceptions produced by x86_decode_insn")
Cc: stable@vger.kernel.org
Cc: Denis Lunev <den@virtuozzo.com>
Cc: Roman Kagan <rkagan@virtuozzo.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Signed-off-by: Jan Dakinevich <jan.dakinevich@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Dakinevich [Tue, 27 Aug 2019 13:07:09 +0000 (13:07 +0000)]
KVM: x86: always stop emulation on page fault
commit
8530a79c5a9f4e29e6ffb35ec1a79d81f4968ec8 upstream.
inject_emulated_exception() returns true if and only if nested page
fault happens. However, page fault can come from guest page tables
walk, either nested or not nested. In both cases we should stop an
attempt to read under RIP and give guest to step over its own page
fault handler.
This is also visible when an emulated instruction causes a #GP fault
and the VMware backdoor is enabled. To handle the VMware backdoor,
KVM intercepts #GP faults; with only the next patch applied,
x86_emulate_instruction() injects a #GP but returns EMULATE_FAIL
instead of EMULATE_DONE. EMULATE_FAIL causes handle_exception_nmi()
(or gp_interception() for SVM) to re-inject the original #GP because it
thinks emulation failed due to a non-VMware opcode. This patch prevents
the issue as x86_emulate_instruction() will return EMULATE_DONE after
injecting the #GP.
Fixes:
6ea6e84309ca ("KVM: x86: inject exceptions produced by x86_decode_insn")
Cc: stable@vger.kernel.org
Cc: Denis Lunev <den@virtuozzo.com>
Cc: Roman Kagan <rkagan@virtuozzo.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Signed-off-by: Jan Dakinevich <jan.dakinevich@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Thu, 5 Sep 2019 14:44:17 +0000 (16:44 +0200)]
parisc: Disable HP HSC-PCI Cards to prevent kernel crash
commit
5fa1659105fac63e0f3c199b476025c2e04111ce upstream.
The HP Dino PCI controller chip can be used in two variants: as on-board
controller (e.g. in B160L), or on an Add-On card ("Card-Mode") to bridge
PCI components to systems without a PCI bus, e.g. to a HSC/GSC bus. One
such Add-On card is the HP HSC-PCI Card which has one or more DEC Tulip
PCI NIC chips connected to the on-card Dino PCI controller.
Dino in Card-Mode has a big disadvantage: All PCI memory accesses need
to go through the DINO_MEM_DATA register, so Linux drivers will not be
able to use the ioremap() function. Without ioremap() many drivers will
not work, one example is the tulip driver which then simply crashes the
kernel if it tries to access the ports on the HP HSC card.
This patch disables the HP HSC card if it finds one, and as such
fixes the kernel crash on a HP D350/2 machine.
Signed-off-by: Helge Deller <deller@gmx.de>
Noticed-by: Phil Scarr <phil.scarr@pm.me>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vasily Averin [Fri, 13 Sep 2019 15:17:11 +0000 (18:17 +0300)]
fuse: fix missing unlock_page in fuse_writepage()
commit
d5880c7a8620290a6c90ced7a0e8bd0ad9419601 upstream.
unlock_page() was missing in case of an already in-flight write against the
same page.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Fixes:
ff17be086477 ("fuse: writepage: skip already in flight")
Cc: <stable@vger.kernel.org> # v3.13
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vincent Whitchurch [Thu, 11 Jul 2019 14:29:37 +0000 (16:29 +0200)]
printk: Do not lose last line in kmsg buffer dump
[ Upstream commit
b46eff55ad5bd98e746c0a7022fe7ee071de5fee ]
kmsg_dump_get_buffer() is supposed to select all the youngest log
messages which fit into the provided buffer. It determines the correct
start index by using msg_print_text() with a NULL buffer to calculate
the size of each entry. However, when performing the actual writes,
msg_print_text() only writes the entry to the buffer if the written len
is lesser than the size of the buffer. So if the lengths of the
selected youngest log messages happen to precisely fill up the provided
buffer, the last log message is not included.
We don't want to modify msg_print_text() to fill up the buffer and start
returning a length which is equal to the size of the buffer, since
callers of its other users, such as kmsg_dump_get_line(), depend upon
the current behaviour.
Instead, fix kmsg_dump_get_buffer() to compensate for this.
For example, with the following two final prints:
[ 6.427502]
AAAAAAAAAAAAA
[ 6.427769]
BBBBBBBB12345
A dump of a 64-byte buffer filled by kmsg_dump_get_buffer(), before this
patch:
00000000: 3c 30 3e 5b 20 20 20 20 36 2e 35 32 32 31 39 37 <0>[ 6.522197
00000010: 5d 20 41 41 41 41 41 41 41 41 41 41 41 41 41 0a ]
AAAAAAAAAAAAA.
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
After this patch:
00000000: 3c 30 3e 5b 20 20 20 20 36 2e 34 35 36 36 37 38 <0>[ 6.456678
00000010: 5d 20 42 42 42 42 42 42 42 42 31 32 33 34 35 0a ]
BBBBBBBB12345.
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Link: http://lkml.kernel.org/r/20190711142937.4083-1-vincent.whitchurch@axis.com
Fixes:
e2ae715d66bf4bec ("kmsg - kmsg_dump() use iterator to receive log buffer content")
To: rostedt@goodmis.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v3.5+
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Sakamoto [Tue, 10 Sep 2019 13:51:52 +0000 (22:51 +0900)]
ALSA: firewire-tascam: check intermediate state of clock status and retry
commit
e1a00b5b253a4f97216b9a33199a863987075162 upstream.
2 bytes in MSB of register for clock status is zero during intermediate
state after changing status of sampling clock in models of TASCAM FireWire
series. The duration of this state differs depending on cases. During the
state, it's better to retry reading the register for current status of
the clock.
In current implementation, the intermediate state is checked only when
getting current sampling transmission frequency, then retry reading.
This care is required for the other operations to read the register.
This commit moves the codes of check and retry into helper function
commonly used for operations to read the register.
Fixes:
e453df44f0d6 ("ALSA: firewire-tascam: add PCM functionality")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20190910135152.29800-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Sakamoto [Tue, 10 Sep 2019 13:51:51 +0000 (22:51 +0900)]
ALSA: firewire-tascam: handle error code when getting current source of clock
commit
2617120f4de6d0423384e0e86b14c78b9de84d5a upstream.
The return value of snd_tscm_stream_get_clock() is ignored. This commit
checks the value and handle error.
Fixes:
e453df44f0d6 ("ALSA: firewire-tascam: add PCM functionality")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20190910135152.29800-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sakari Ailus [Wed, 7 Aug 2019 14:19:00 +0000 (11:19 -0300)]
media: omap3isp: Set device on omap3isp subdevs
[ Upstream commit
e9eb103f027725053a4b02f93d7f2858b56747ce ]
The omap3isp driver registered subdevs without the dev field being set. Do
that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qu Wenruo [Tue, 16 Jul 2019 09:00:33 +0000 (17:00 +0800)]
btrfs: extent-tree: Make sure we only allocate extents from block groups with the same type
[ Upstream commit
2a28468e525f3924efed7f29f2bc5a2926e7e19a ]
[BUG]
With fuzzed image and MIXED_GROUPS super flag, we can hit the following
BUG_ON():
kernel BUG at fs/btrfs/delayed-ref.c:491!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 1849 Comm: sync Tainted: G O 5.2.0-custom #27
RIP: 0010:update_existing_head_ref.cold+0x44/0x46 [btrfs]
Call Trace:
add_delayed_ref_head+0x20c/0x2d0 [btrfs]
btrfs_add_delayed_tree_ref+0x1fc/0x490 [btrfs]
btrfs_free_tree_block+0x123/0x380 [btrfs]
__btrfs_cow_block+0x435/0x500 [btrfs]
btrfs_cow_block+0x110/0x240 [btrfs]
btrfs_search_slot+0x230/0xa00 [btrfs]
? __lock_acquire+0x105e/0x1e20
btrfs_insert_empty_items+0x67/0xc0 [btrfs]
alloc_reserved_file_extent+0x9e/0x340 [btrfs]
__btrfs_run_delayed_refs+0x78e/0x1240 [btrfs]
? kvm_clock_read+0x18/0x30
? __sched_clock_gtod_offset+0x21/0x50
btrfs_run_delayed_refs.part.0+0x4e/0x180 [btrfs]
btrfs_run_delayed_refs+0x23/0x30 [btrfs]
btrfs_commit_transaction+0x53/0x9f0 [btrfs]
btrfs_sync_fs+0x7c/0x1c0 [btrfs]
? __ia32_sys_fdatasync+0x20/0x20
sync_fs_one_sb+0x23/0x30
iterate_supers+0x95/0x100
ksys_sync+0x62/0xb0
__ia32_sys_sync+0xe/0x20
do_syscall_64+0x65/0x240
entry_SYSCALL_64_after_hwframe+0x49/0xbe
[CAUSE]
This situation is caused by several factors:
- Fuzzed image
The extent tree of this fs missed one backref for extent tree root.
So we can allocated space from that slot.
- MIXED_BG feature
Super block has MIXED_BG flag.
- No mixed block groups exists
All block groups are just regular ones.
This makes data space_info->block_groups[] contains metadata block
groups. And when we reserve space for data, we can use space in
metadata block group.
Then we hit the following file operations:
- fallocate
We need to allocate data extents.
find_free_extent() choose to use the metadata block to allocate space
from, and choose the space of extent tree root, since its backref is
missing.
This generate one delayed ref head with is_data = 1.
- extent tree update
We need to update extent tree at run_delayed_ref time.
This generate one delayed ref head with is_data = 0, for the same
bytenr of old extent tree root.
Then we trigger the BUG_ON().
[FIX]
The quick fix here is to check block_group->flags before using it.
The problem can only happen for MIXED_GROUPS fs. Regular filesystems
won't have space_info with DATA|METADATA flag, and no way to hit the
bug.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203255
Reported-by: Jungyeon Yoon <jungyeon.yoon@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Iwai [Thu, 22 Aug 2019 07:58:07 +0000 (09:58 +0200)]
ALSA: hda/realtek - Blacklist PC beep for Lenovo ThinkCentre M73/93
[ Upstream commit
051c78af14fcd74a22b5af45548ad9d588247cc7 ]
Lenovo ThinkCentre M73 and M93 don't seem to have a proper beep
although the driver tries to probe and set up blindly.
Blacklist these machines for suppressing the beep creation.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204635
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>