OSDN Git Service
Hans Verkuil [Mon, 30 Nov 2015 12:19:41 +0000 (10:19 -0200)]
[media] cx25840: relax a Vsrc check
The cx23888 reports a slightly different Vsrc value than the other
chip variants do. Relax the check by 1, otherwise cx25840_set_fmt()
would fail for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 30 Nov 2015 12:15:21 +0000 (10:15 -0200)]
[media] cx25840: more cx23888 register address changes
The cx23888 also moves the following registers around:
!cx23888 cx23888
-------- -------
0x418, 0x41c 0x434, 0x438
0x420 0x418 (expect for bit 29 which has a different meaning)
0x478 0x454
Also drop the set_input code where the scaler is changed: this does not
belong here, changing the input should not change the scaler.
And that's besides the fact that that code is plain wrong.
After this change the cx23888 behaves much better. In particular, calling
set_input no longer changes the saturation to 0, causing a grayscale
image.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 30 Nov 2015 12:09:50 +0000 (10:09 -0200)]
[media] cx25840: fix VBI support for cx23888
The cx23888 has the VBI registers at different addresses compared to
the other variants. In most cases it is a fixed offset, but not always.
Update the code so the right registers are written for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 30 Nov 2015 12:05:53 +0000 (10:05 -0200)]
[media] ivtv/cx18: fix inverted pixel aspect ratio
These two drivers reported the pixel aspect ratio the wrong way around.
This caused qv4l2 to scale the image incorrectly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 30 Nov 2015 12:03:30 +0000 (10:03 -0200)]
[media] cx231xx: fix NTSC cropcap, add missing cropcap for 417
The pixelaspect ratio was set incorrectly for 60Hz formats.
And since cropcap wasn't implemented at all for the -417 (compressed
video) the pixelaspect was unknown for compressed video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 30 Nov 2015 11:59:18 +0000 (09:59 -0200)]
[media] cx23885: fix format/crop handling
While testing the cx23885 driver with various TV standards I found
a number of bugs:
1) norm_maxw() returned 768 instead of 720 for PAL formats. This should
always be 720, so drop this inline function and just always use 720.
2) cropcap() was missing, so the pixelaspect was never known and qv4l2 would
scale the image incorrectly. Add cropcap support.
3) cx23885_set_tvnorm() should just return 0 if the same standard was
set again. If another standard is set, then reset the width/height and
call set_fmt for the subdevs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro Carvalho Chehab [Sat, 12 Dec 2015 10:10:40 +0000 (08:10 -0200)]
Revert "[media] UVC: Add support for ds4 depth camera"
This reverts commit
120c41d3477a23c6941059401db63677736f1935.
The patch doesn't add the corresponding documentation bits to the
media infrastructure uAPI DocBook. Also, they're for 3D formats,
with requre further discussions.
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Mauro Carvalho Chehab [Fri, 4 Dec 2015 12:38:59 +0000 (10:38 -0200)]
[media] use https://linuxtv.org for LinuxTV URLs
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro Carvalho Chehab [Fri, 4 Dec 2015 12:36:22 +0000 (10:36 -0200)]
drm, ipu-v3: use https://linuxtv.org for LinuxTV URL
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change the references at DRM include and at
the ipu-v3 driver to point to the https://linuxtv.org
URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro Carvalho Chehab [Fri, 4 Dec 2015 12:34:32 +0000 (10:34 -0200)]
WHENCE: use https://linuxtv.org for LinuxTV URLs
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change the http://linuxtv.org references at firmware/WHENCE
file to point to https://linuxtv.org instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro Carvalho Chehab [Fri, 4 Dec 2015 12:31:23 +0000 (10:31 -0200)]
MAINTAINERS: use https://linuxtv.org for LinuxTV URLs
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at MAINTAINERS file
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Arnd Bergmann [Wed, 25 Nov 2015 15:13:26 +0000 (13:13 -0200)]
[media] staging: media: lirc: Replace timeval with ktime_t in lirc_parallel.c
'struct timeval tv' and 'struct timeval now' is used to calculate the
elapsed time. 'LIRC_SFH506_DELAY' is a delay t_phl in usecs.
32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the lirc_parallel.c file of media: lirc driver
to use ktime_t.
ktime_get() is better than using do_gettimeofday(),
because it uses the monotonic clock. ktime_sub is used
to subtract two ktime variables. ktime_to_us() is used to
convert ktime to microsecond.
New ktime_t variable timeout, is added in lirc_off(),to improve
clarity. Introduced a new ktime_t variable in lirc_lirc_irq_handler()
function, to avoid the use of signal variable for storing
seconds in the first part of this function as later it uses
a time unit that is defined by the global "timer" variable.
This makes it more clear.
ktime_set() is used to set a value in seconds to a value in
nanosecond so that ktime_compare() can be used appropriately.
ktime_compare() is used to compare two ktime values.
ktime_add_ns() is used to increment a ktime value by 1 sec.
One comment is also shifted a line up, as it was creating a 80
character warning.
Build tested it. Also tested it with sparse.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Arnd Bergmann [Wed, 25 Nov 2015 15:12:53 +0000 (13:12 -0200)]
[media] staging: media: lirc: Replace timeval with ktime_t in lirc_sasem.c
'struct timeval presstime' and 'struct timeval tv' is used to
calculate the time since the last button press.
32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the media: lirc driver to use ktime_t.
ktime_get() is better than using do_gettimeofday(), because it uses
the monotonic clock. ktime_sub() are used to subtract two ktime
variables. 'ms' is only used to check how much time has passed by comparing
to 250. So instead of using expensive ktime_to_ms() call, it has been
changed to hold nanoseconds by using ktime_to_ns().
Build tested it. Tested with sparse too.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Arnd Bergmann [Wed, 25 Nov 2015 15:11:55 +0000 (13:11 -0200)]
[media] staging: media: lirc: Replace timeval with ktime_t in lirc_serial.c
'struct timeval tv' is used to get current time.
'static struct timeval lasttv' is used to get last interrupt time.
32-bit systems using 'struct timeval' will break in the year 2038,
so we have to replace that code with more appropriate types.
This patch changes the lirc_serial.c file of media: lirc to use
ktime_t.
ktime_get() is better than using do_gettimeofday(),
because it uses the monotonic clock. ktime_sub is used
to subtract two ktime variables. The check to test time
going backwards is also removed. Intialization to static
variable is also removed. ktime_to_us() is used to convert
ktime_t to microsecond value. deltv is changed to delkt, a
ktime_t type varibale from long to assign the ktime_sub value
directly. ktime_compare is used to compare delkt with 15
seconds, which is changed to a nanosecond value by using
ktime_set().
Build tested it.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Joseph Marrero [Tue, 24 Nov 2015 21:30:18 +0000 (19:30 -0200)]
[media] radio-bcm2048: fix code indent
Fixes a warning message found by checkpatch.pl WARNING:
suspect code indent for conditional statements
Signed-off-by: Joseph Marrero <jmarrero@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Mon, 23 Nov 2015 19:19:04 +0000 (17:19 -0200)]
[media] tda10071: Fix dependency to REGMAP_I2C
Without I get this error for by dvb-card:
tda10071: Unknown symbol devm_regmap_init_i2c (err 0)
cx23885_dvb_register() dvb_register failed err = -22
cx23885_dev_setup() Failed to register dvb adapters on VID_B
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Lars-Peter Clausen [Sat, 21 Nov 2015 11:16:38 +0000 (09:16 -0200)]
[media] dm1105: Remove unnecessary synchronize_irq() before free_irq()
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Heiner Kallweit [Sat, 21 Nov 2015 14:55:03 +0000 (12:55 -0200)]
[media] media: rc: remove unneeded code
Now that that the decoder modules are loaded on-demand we can move
loading the lirc module to rc_register_device directly and remove
unneeded functions and comments.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:04:02 +0000 (18:04 -0200)]
[media] si2165: Add DVB-C support for HVR-4400/HVR-5500
It works only for HVR-4400/HVR-5500.
For WinTV-HVR-930C-HD it fails with bad/no reception
for unknown reasons.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:04:01 +0000 (18:04 -0200)]
[media] si2165: Prepare si2165_set_frontend() for future DVB-C support
The current si2165_set_frontend() function actually works only for DVB-T.
Split it into two functions, preparing the code to support DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:04:00 +0000 (18:04 -0200)]
[media] si2165: set list of DVB-T registers together
Use si2165_write_reg_list() to do the DVB-T mode initialization altogether.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:03:58 +0000 (18:03 -0200)]
[media] si2165: Simplify si2165_set_if_freq_shift usage
si2165_set_if_freq_shift() needs to call get_if_frequency() in order to do
the right shift. Add such logic inside the function, simplifying the logic
for the callers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:03:57 +0000 (18:03 -0200)]
[media] si2165: move setting ts config to init
The TS config is fixed, so no need to write it for each tune.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:03:56 +0000 (18:03 -0200)]
[media] si2165: only write agc registers after reset before start_syncro
Datasheet says they must be rewritten after reset.
But it only makes sense to write them when trying to tune afterwards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:03:55 +0000 (18:03 -0200)]
[media] si2165: create function si2165_write_reg_list for writing register lists
It is common the need of writing a table of values. Add a function to provide a
helper to address such case. This will allow further code cleanups.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:03:54 +0000 (18:03 -0200)]
[media] si2165: rename si2165_set_parameters to si2165_set_frontend
No functional changes.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Matthias Schwarzott [Thu, 19 Nov 2015 20:03:53 +0000 (18:03 -0200)]
[media] si2165: rename frontend -> fe
No functional changes.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Aviv Greenberg [Fri, 16 Oct 2015 11:48:51 +0000 (08:48 -0300)]
[media] UVC: Add support for ds4 depth camera
Add support for Intel DS4 depth camera in uvc driver.
This includes adding new uvc GUIDs for the new pixel formats,
adding new V4L pixel format definition to user api headers,
and updating the uvc driver GUID-to-4cc tables with the new formats.
Change-Id: If240d95a7d4edc8dcc3e02d58cd8267a6bbf6fcb
Tested-by: Greenberg, Aviv D <aviv.d.greenberg@intel.com>
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Julia Lawall [Sun, 22 Nov 2015 17:44:38 +0000 (15:44 -0200)]
[media] cx231xx: constify cx2341x_handler_ops structures
The cx2341x_handler_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Julia Lawall [Sun, 22 Nov 2015 10:32:53 +0000 (08:32 -0200)]
[media] media, sound: tea575x: constify snd_tea575x_ops structures
The snd_tea575x_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Fri, 13 Nov 2015 11:46:26 +0000 (09:46 -0200)]
[media] v4l2-dv-timings: add new arg to v4l2_match_dv_timings
Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro Carvalho Chehab [Mon, 23 Nov 2015 16:16:58 +0000 (14:16 -0200)]
Merge tag 'v4.4-rc2' into patchwork
Linux 4.4-rc2
Several PCI media drivers got broken on Kernel 4.4-rc1, due to
pci_set_dma_mask() regressions. So, we need to add those fixes back
for the media drivers to work again.
* tag 'v4.4-rc2': (335 commits)
Linux 4.4-rc2
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
parisc: Map kernel text and data on huge pages
parisc: Add Huge Page and HUGETLBFS support
parisc: Use long branch to do_syscall_trace_exit
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
parisc: Initialize the fault vector earlier in the boot process.
parisc: Add defines for Huge page support
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
...
Linus Torvalds [Mon, 23 Nov 2015 00:45:59 +0000 (16:45 -0800)]
Linux 4.4-rc2
Linus Torvalds [Sun, 22 Nov 2015 23:21:40 +0000 (15:21 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge slub bulk allocator updates from Andrew Morton:
"This missed the merge window because I was waiting for some repairs to
come in. Nothing actually uses the bulk allocator yet and the changes
to other code paths are pretty small. And the net guys are waiting
for this so they can start merging the client code"
More comments from Jesper Dangaard Brouer:
"The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
previous kernel. The present version contains a bug. Vladimir
Davydov noticed it contained a bug, when kernel is compiled with
CONFIG_MEMCG_KMEM (see commit
03ec0ed57ffc: "slub: fix kmem cgroup
bug in kmem_cache_alloc_bulk"). Plus the mem cgroup counterpart in
kmem_cache_free_bulk() were missing (see commit
033745189b1b "slub:
add missing kmem cgroup support to kmem_cache_free_bulk").
I don't consider the fix stable-material because there are no in-tree
users of the API.
But with known bugs (for memcg) I cannot start using the API in the
net-tree"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
Linus Torvalds [Sun, 22 Nov 2015 23:10:57 +0000 (15:10 -0800)]
Merge tag 'tty-4.4-rc2' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below"
* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
tty: Fix tty_send_xchar() lock order inversion
Linus Torvalds [Sun, 22 Nov 2015 21:26:24 +0000 (13:26 -0800)]
Merge tag 'staging-4.4-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while"
* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
iio: adc: xilinx: Fix VREFN scale
iio: si7020: Swap data byte order
iio: adc: vf610_adc: Fix division by zero error
iio:ad7793: Fix ad7785 product ID
iio: ad5064: Fix ad5629/ad5669 shift
iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
vf610_adc: Fix internal temperature calculation
Linus Torvalds [Sun, 22 Nov 2015 21:15:05 +0000 (13:15 -0800)]
Merge tag 'usb-4.4-rc2' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes and new device ids for 4.4-rc2. All
have been in linux-next and the details are in the shortlog"
* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usblp: do not set TASK_INTERRUPTIBLE before lock
USB: MAINTAINERS: cxacru
usb: kconfig: fix warning of select USB_OTG
USB: option: add XS Stick W100-2 from 4G Systems
xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
usb: xhci: fix checking ep busy for CFC
xhci: Workaround to get Intel xHCI reset working more reliably
usb: chipidea: imx: fix a possible NULL dereference
usb: chipidea: usbmisc_imx: fix a possible NULL dereference
usb: chipidea: otg: gadget module load and unload support
usb: chipidea: debug: disable usb irq while role switch
ARM: dts: imx27.dtsi: change the clock information for usb
usb: chipidea: imx: refine clock operations to adapt for all platforms
usb: gadget: atmel_usba_udc: Expose correct device speed
usb: musb: enable usb_dma parameter
usb: phy: phy-mxs-usb: fix a possible NULL dereference
usb: dwc3: gadget: let us set lower max_speed
usb: musb: fix tx fifo flush handling
usb: gadget: f_loopback: fix the warning during the enumeration
usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
...
Linus Torvalds [Sun, 22 Nov 2015 20:59:46 +0000 (12:59 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- Fix a flood of annoying build warnings
- A number of fixes for Atheros 79xx platforms
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ath79: Add a machine entry for booting OF machines
MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
MIPS: Fix flood of warnings about comparsion being always true.
Linus Torvalds [Sun, 22 Nov 2015 20:50:58 +0000 (12:50 -0800)]
Merge branch 'parisc-4.4-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc update from Helge Deller:
"This patchset adds Huge Page and HUGETLBFS support for parisc"
Honestly, the hugepage support should have gone through in the merge
window, and is not really an rc-time fix. But it only touches
arch/parisc, and I cannot find it in myself to care. If one of the
three parisc users notices a breakage, I will point at Helge and make
rude farting noises.
* 'parisc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Map kernel text and data on huge pages
parisc: Add Huge Page and HUGETLBFS support
parisc: Use long branch to do_syscall_trace_exit
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
parisc: Initialize the fault vector earlier in the boot process.
parisc: Add defines for Huge page support
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
parisc: Drop definition of start_thread_som for HP-UX SOM binaries
parisc: Fix wrong comment regarding first pmd entry flags
Linus Torvalds [Sun, 22 Nov 2015 20:37:20 +0000 (12:37 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tool fixes from Thomas Gleixner:
"A couple of fixes for perf tools:
- Build system updates
- Plug a memory leak in an error path of perf probe
- Tear down probes correctly when adding fails
- Fixes to the perf symbol handling
- Fix ordering of event processing in buildid-list
- Fix per DSO filtering in the histogram browser"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Clear probe_trace_event when add_probe_trace_event() fails
perf probe: Fix memory leaking on failure by clearing all probe_trace_events
perf inject: Also re-pipe lost_samples event
perf buildid-list: Requires ordered events
perf symbols: Fix dso lookup by long name and missing buildids
perf symbols: Allow forcing reading of non-root owned files by root
perf hists browser: The dso can be obtained from popup_action->ms.map->dso
perf hists browser: Fix 'd' hotkey action to filter by DSO
perf symbols: Rebuild rbtree when adjusting symbols for kcore
tools: Add a "make all" rule
tools: Actually install tmon in the install rule
Linus Torvalds [Sun, 22 Nov 2015 20:00:12 +0000 (12:00 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- MPX updates for handling 32bit processes
- A fix for a long standing bug in 32bit signal frame handling
related to FPU/XSAVE state
- Handle get_xsave_addr() correctly in KVM
- Fix SMAP check under paravirtualization
- Add a comment to the static function trace entry to avoid further
confusion about the difference to dynamic tracing"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix SMAP check in PVOPS environments
x86/ftrace: Add comment on static function tracing
x86/fpu: Fix get_xsave_addr() behavior under virtualization
x86/fpu: Fix 32-bit signal frame handling
x86/mpx: Fix 32-bit address space calculation
x86/mpx: Do proper get_user() when running 32-bit binaries on 64-bit kernels
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:58 +0000 (15:57 -0800)]
slab/slub: adjust kmem_cache_alloc_bulk API
Adjust kmem_cache_alloc_bulk API before we have any real users.
Adjust API to return type 'int' instead of previously type 'bool'. This
is done to allow future extension of the bulk alloc API.
A future extension could be to allow SLUB to stop at a page boundary, when
specified by a flag, and then return the number of objects.
The advantage of this approach, would make it easier to make bulk alloc
run without local IRQs disabled. With an approach of cmpxchg "stealing"
the entire c->freelist or page->freelist. To avoid overshooting we would
stop processing at a slab-page boundary. Else we always end up returning
some objects at the cost of another cmpxchg.
To keep compatible with future users of this API linking against an older
kernel when using the new flag, we need to return the number of allocated
objects with this API change.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:55 +0000 (15:57 -0800)]
slub: add missing kmem cgroup support to kmem_cache_free_bulk
Initial implementation missed support for kmem cgroup support in
kmem_cache_free_bulk() call, add this.
If CONFIG_MEMCG_KMEM is not enabled, the compiler should be smart enough
to not add any asm code.
Incoming bulk free objects can belong to different kmem cgroups, and
object free call can happen at a later point outside memcg context. Thus,
we need to keep the orig kmem_cache, to correctly verify if a memcg object
match against its "root_cache" (s->memcg_params.root_cache).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:52 +0000 (15:57 -0800)]
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
The call slab_pre_alloc_hook() interacts with kmemgc and is not allowed to
be called several times inside the bulk alloc for loop, due to the call to
memcg_kmem_get_cache().
This would result in hitting the VM_BUG_ON in __memcg_kmem_get_cache.
As suggested by Vladimir Davydov, change slab_post_alloc_hook() to be able
to handle an array of objects.
A subtle detail is, loop iterator "i" in slab_post_alloc_hook() must have
same type (size_t) as size argument. This helps the compiler to easier
realize that it can remove the loop, when all debug statements inside loop
evaluates to nothing. Note, this is only an issue because the kernel is
compiled with GCC option: -fno-strict-overflow
In slab_alloc_node() the compiler inlines and optimizes the invocation of
slab_post_alloc_hook(s, flags, 1, &object) by removing the loop and access
object directly.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Suggested-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:49 +0000 (15:57 -0800)]
slub: optimize bulk slowpath free by detached freelist
This change focus on improving the speed of object freeing in the
"slowpath" of kmem_cache_free_bulk.
The calls slab_free (fastpath) and __slab_free (slowpath) have been
extended with support for bulk free, which amortize the overhead of
the (locked) cmpxchg_double.
To use the new bulking feature, we build what I call a detached
freelist. The detached freelist takes advantage of three properties:
1) the free function call owns the object that is about to be freed,
thus writing into this memory is synchronization-free.
2) many freelist's can co-exist side-by-side in the same slab-page
each with a separate head pointer.
3) it is the visibility of the head pointer that needs synchronization.
Given these properties, the brilliant part is that the detached
freelist can be constructed without any need for synchronization. The
freelist is constructed directly in the page objects, without any
synchronization needed. The detached freelist is allocated on the
stack of the function call kmem_cache_free_bulk. Thus, the freelist
head pointer is not visible to other CPUs.
All objects in a SLUB freelist must belong to the same slab-page.
Thus, constructing the detached freelist is about matching objects
that belong to the same slab-page. The bulk free array is scanned is
a progressive manor with a limited look-ahead facility.
Kmem debug support is handled in call of slab_free().
Notice kmem_cache_free_bulk no longer need to disable IRQs. This
only slowed down single free bulk with approx 3 cycles.
Performance data:
Benchmarked[1] obj size 256 bytes on CPU i7-4790K @ 4.00GHz
SLUB fastpath single object quick reuse: 47 cycles(tsc) 11.931 ns
To get stable and comparable numbers, the kernel have been booted with
"slab_merge" (this also improve performance for larger bulk sizes).
Performance data, compared against fallback bulking:
bulk - fallback bulk - improvement with this patch
1 - 62 cycles(tsc) 15.662 ns - 49 cycles(tsc) 12.407 ns- improved 21.0%
2 - 55 cycles(tsc) 13.935 ns - 30 cycles(tsc) 7.506 ns - improved 45.5%
3 - 53 cycles(tsc) 13.341 ns - 23 cycles(tsc) 5.865 ns - improved 56.6%
4 - 52 cycles(tsc) 13.081 ns - 20 cycles(tsc) 5.048 ns - improved 61.5%
8 - 50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.659 ns - improved 64.0%
16 - 49 cycles(tsc) 12.412 ns - 17 cycles(tsc) 4.495 ns - improved 65.3%
30 - 49 cycles(tsc) 12.484 ns - 18 cycles(tsc) 4.533 ns - improved 63.3%
32 - 50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.707 ns - improved 64.0%
34 - 96 cycles(tsc) 24.243 ns - 23 cycles(tsc) 5.976 ns - improved 76.0%
48 - 83 cycles(tsc) 20.818 ns - 21 cycles(tsc) 5.329 ns - improved 74.7%
64 - 74 cycles(tsc) 18.700 ns - 20 cycles(tsc) 5.127 ns - improved 73.0%
128 - 90 cycles(tsc) 22.734 ns - 27 cycles(tsc) 6.833 ns - improved 70.0%
158 - 99 cycles(tsc) 24.776 ns - 30 cycles(tsc) 7.583 ns - improved 69.7%
250 - 104 cycles(tsc) 26.089 ns - 37 cycles(tsc) 9.280 ns - improved 64.4%
Performance data, compared current in-kernel bulking:
bulk - curr in-kernel - improvement with this patch
1 - 46 cycles(tsc) - 49 cycles(tsc) - improved (cycles:-3) -6.5%
2 - 27 cycles(tsc) - 30 cycles(tsc) - improved (cycles:-3) -11.1%
3 - 21 cycles(tsc) - 23 cycles(tsc) - improved (cycles:-2) -9.5%
4 - 18 cycles(tsc) - 20 cycles(tsc) - improved (cycles:-2) -11.1%
8 - 17 cycles(tsc) - 18 cycles(tsc) - improved (cycles:-1) -5.9%
16 - 18 cycles(tsc) - 17 cycles(tsc) - improved (cycles: 1) 5.6%
30 - 18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0) 0.0%
32 - 18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0) 0.0%
34 - 78 cycles(tsc) - 23 cycles(tsc) - improved (cycles:55) 70.5%
48 - 60 cycles(tsc) - 21 cycles(tsc) - improved (cycles:39) 65.0%
64 - 49 cycles(tsc) - 20 cycles(tsc) - improved (cycles:29) 59.2%
128 - 69 cycles(tsc) - 27 cycles(tsc) - improved (cycles:42) 60.9%
158 - 79 cycles(tsc) - 30 cycles(tsc) - improved (cycles:49) 62.0%
250 - 86 cycles(tsc) - 37 cycles(tsc) - improved (cycles:49) 57.0%
Performance with normal SLUB merging is significantly slower for
larger bulking. This is believed to (primarily) be an effect of not
having to share the per-CPU data-structures, as tuning per-CPU size
can achieve similar performance.
bulk - slab_nomerge - normal SLUB merge
1 - 49 cycles(tsc) - 49 cycles(tsc) - merge slower with cycles:0
2 - 30 cycles(tsc) - 30 cycles(tsc) - merge slower with cycles:0
3 - 23 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:0
4 - 20 cycles(tsc) - 20 cycles(tsc) - merge slower with cycles:0
8 - 18 cycles(tsc) - 18 cycles(tsc) - merge slower with cycles:0
16 - 17 cycles(tsc) - 17 cycles(tsc) - merge slower with cycles:0
30 - 18 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:5
32 - 18 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:4
34 - 23 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:-1
48 - 21 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:1
64 - 20 cycles(tsc) - 48 cycles(tsc) - merge slower with cycles:28
128 - 27 cycles(tsc) - 57 cycles(tsc) - merge slower with cycles:30
158 - 30 cycles(tsc) - 59 cycles(tsc) - merge slower with cycles:29
250 - 37 cycles(tsc) - 56 cycles(tsc) - merge slower with cycles:19
Joint work with Alexander Duyck.
[1] https://github.com/netoptimizer/prototype-kernel/blob/master/kernel/mm/slab_bulk_test01.c
[akpm@linux-foundation.org: BUG_ON -> WARN_ON;return]
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:46 +0000 (15:57 -0800)]
slub: support for bulk free with SLUB freelists
Make it possible to free a freelist with several objects by adjusting API
of slab_free() and __slab_free() to have head, tail and an objects counter
(cnt).
Tail being NULL indicate single object free of head object. This allow
compiler inline constant propagation in slab_free() and
slab_free_freelist_hook() to avoid adding any overhead in case of single
object free.
This allows a freelist with several objects (all within the same
slab-page) to be free'ed using a single locked cmpxchg_double in
__slab_free() and with an unlocked cmpxchg_double in slab_free().
Object debugging on the free path is also extended to handle these
freelists. When CONFIG_SLUB_DEBUG is enabled it will also detect if
objects don't belong to the same slab-page.
These changes are needed for the next patch to bulk free the detached
freelists it introduces and constructs.
Micro benchmarking showed no performance reduction due to this change,
when debugging is turned off (compiled with CONFIG_SLUB_DEBUG).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helge Deller [Sat, 21 Nov 2015 23:07:44 +0000 (00:07 +0100)]
parisc: Map kernel text and data on huge pages
Adjust the linker script and map_pages() to map kernel text and data on
physical 1MB huge/large pages.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sat, 21 Nov 2015 23:07:06 +0000 (00:07 +0100)]
parisc: Add Huge Page and HUGETLBFS support
This patch adds huge page support to allow userspace to allocate huge
pages and to use hugetlbfs filesystem on 32- and 64-bit Linux kernels.
A later patch will add kernel support to map kernel text and data on
huge pages.
The only requirement is, that the kernel needs to be compiled for a
PA8X00 CPU (PA2.0 architecture). Older PA1.X CPUs do not support
variable page sizes. 64bit Kernels are compiled for PA2.0 by default.
Technically on parisc multiple physical huge pages may be needed to
emulate standard 2MB huge pages.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 10:22:32 +0000 (11:22 +0100)]
parisc: Use long branch to do_syscall_trace_exit
Use the 22bit instead of the 17bit branch instruction on a 64bit kernel
to reach the do_syscall_trace_exit function from the gateway page.
A huge page enabled kernel may need the additional branch distance bits.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 10:17:27 +0000 (11:17 +0100)]
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
For the 64bit kernel the initially 16 MB kernel memory might become too
small if you build a kernel with many modules built-in and with kernel
text and data areas mapped on huge pages.
This patch increases the initial mapping to 32MB for 64bit kernels and
keeps 16MB for 32bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 09:50:01 +0000 (10:50 +0100)]
parisc: Initialize the fault vector earlier in the boot process.
A fault vector on parisc needs to be 2K aligned. Furthermore the
checksum of the fault vector needs to sum up to 0 which is being
calculated and written at runtime.
Up to now we aligned both PA20 and PA11 fault vectors on the same 4K
page in order to easily write the checksum after having mapped the
kernel read-only (by mapping this page only as read-write).
But when we want to map the kernel text and data on huge pages this
makes things harder.
So, simplify it by aligning both fault vectors on 2K boundries and write
the checksum before we map the page read-only.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 14:46:52 +0000 (15:46 +0100)]
parisc: Add defines for Huge page support
Huge pages on parisc will have the same size as one pmd table, which
is on a 64bit kernel 2MB on a kernel with 4K kernel page sizes, and
on a 32bit kernel 4MB when used with 4K kernel pages.
Since parisc does not physically supports 2MB huge page sizes, emulate
it with two consecutive 1MB page sizes instead. Keeping the same huge
page size as one pmd will allow us to add transparent huge page support
later on.
Bit 21 in the pte flags was unused and will now be used to mark a page
as huge page (_PAGE_HPAGE_BIT).
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sun, 22 Nov 2015 11:14:14 +0000 (12:14 +0100)]
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
Drop the MADV_xxK_PAGES flags, which were never used and were from a proposed
API which was never integrated into the generic Linux kernel code.
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Linus Torvalds [Sat, 21 Nov 2015 18:49:13 +0000 (10:49 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"A bunch of fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slub: mark the dangling ifdef #else of CONFIG_SLUB_DEBUG
slub: avoid irqoff/on in bulk allocation
slub: create new ___slab_alloc function that can be called with irqs disabled
mm: fix up sparse warning in gfpflags_allow_blocking
ocfs2: fix umask ignored issue
PM/OPP: add entry in MAINTAINERS
kernel/panic.c: turn off locks debug before releasing console lock
kernel/signal.c: unexport sigsuspend()
kasan: fix kmemleak false-positive in kasan_module_alloc()
fat: fix fake_offset handling on error path
mm/hugetlbfs: fix bugs in fallocate hole punch of areas with holes
mm/page-writeback.c: initialize m_dirty to avoid compile warning
various: fix pci_set_dma_mask return value checking
mm: loosen MADV_NOHUGEPAGE to enable Qemu postcopy on s390
mm: vmalloc: don't remove inexistent guard hole in remove_vm_area()
tools/vm/page-types.c: support KPF_IDLE
ncpfs: don't allow negative timeouts
configfs: allow dynamic group creation
MAINTAINERS: add Moritz as reviewer for FPGA Manager Framework
slab.h: sprinkle __assume_aligned attributes
Linus Torvalds [Sat, 21 Nov 2015 18:26:24 +0000 (10:26 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two timer fixlets from Arnd:
- Use proper constant size in the FSL timer driver
- Prevent a build error for legacy platforms"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Disallow drivers for ARCH_USES_GETTIMEOFFSET
clocksource/fsl: Avoid harmless 64-bit warnings
Linus Torvalds [Sat, 21 Nov 2015 18:19:15 +0000 (10:19 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Three fixes for the ARM GIC interrupt controller from Marc addressing
various shortcomings versus boot initialization and suspend/resume"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic: Add save/restore of the active state
irqchip/gic: Clear enable bits before restoring them
irqchip/gic: Make sure all interrupts are deactivated at boot
Linus Torvalds [Sat, 21 Nov 2015 17:52:07 +0000 (09:52 -0800)]
Merge tag 'for-linus-
20151120' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates for brcmnand driver
- Fix reboot hangs seen when multiple NAND flash chips are registered
with the same controller
- Fix build issues on jz4740 NAND driver; the error was introduced in
4.3, so I guess nobody really cared, but we might as well fix it
* tag 'for-linus-
20151120' of git://git.infradead.org/linux-mtd:
MAINTAINERS: brcmnand: Add co-maintainer for Broadcom SoCs
MAINTAINERS: brcmnand: Add Broadcom internal mailing-list
mtd: nand: fix shutdown/reboot for multi-chip systems
mtd: jz4740_nand: fix build on jz4740 after removing gpio.h
Arnd Bergmann [Mon, 16 Nov 2015 15:48:09 +0000 (16:48 +0100)]
serial: export fsl8250_handle_irq
fsl8250_handle_irq is now used by the of_serial driver, and that fails
if it is a loadable module:
ERROR: "fsl8250_handle_irq" [drivers/tty/serial/of_serial.ko] undefined!
This exports the symbol to avoid randconfig errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
d43b54d269d2 ("serial: Enable Freescale 16550 workaround on arm")
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 12 Nov 2015 13:21:23 +0000 (15:21 +0200)]
serial: 8250_mid: Add missing dependency
8250_mid uses rational_best_approximation() function, so the
driver needs to select CONFIG_RATIONAL option.
This fixes build error when CONFIG_RATIONAL is not enabled:
drivers/built-in.o: In function `mid8250_set_termios':
8250_mid.c:(.text+0x10169a): undefined reference to `rational_best_approximation'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 8 Nov 2015 13:52:31 +0000 (08:52 -0500)]
tty: audit: Fix audit source
The data to audit/record is in the 'from' buffer (ie., the input
read buffer).
Fixes:
72586c6061ab ("n_tty: Fix auditing support for cannonical mode")
Cc: stable <stable@vger.kernel.org> # 4.1+
Cc: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Mon, 2 Nov 2015 02:32:56 +0000 (18:32 -0800)]
serial: etraxfs-uart: Fix crash
Since commit
7d8c70d8048c ("serial: mctrl-gpio: rename init function"),
crisv32 either do not build or crash as follows.
Unable to handle kernel NULL pointer dereference
Linux 4.3.0-rc7-next-
20151101 #1 Sun Nov 1 11:41:28 PST 2015
...
Call Trace: [<
c0004a0e>] show_stack+0x0/0x9e
[<
c004c0c0>] printk+0x0/0x2c
[<
c00059d4>] show_registers+0x14a/0x1c2
[<
c004c0c0>] printk+0x0/0x2c
[<
c0004b52>] die_if_kernel+0x7c/0x9e
[<
c0005346>] do_page_fault+0x32e/0x3e6
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c01e0558>] of_irq_parse_raw+0x12a/0x376
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c0053aca>] get_page_from_freelist+0x73e/0x856
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c0008912>] d_mmu_refill+0x10a/0x112
[<
c01b488c>] devm_kmalloc+0x40/0x56
[<
c01b47d0>] add_dr+0xc/0x1c
[<
c01b4800>] devm_add_action+0x2/0x4e
[<
c01abdbc>] mctrl_gpio_init_noauto+0x1c/0x76
[<
c01abf9e>] mctrl_gpio_init+0x22/0x110
The function call in the etraxfs-uart driver was not renamed,
possibly due to interference with commit
7b9c5162c182 ("serial:
etraxfs-uart: use mctrl_gpio helpers for handling modem signals").
Fixes:
7d8c70d8048c ("serial: mctrl-gpio: rename init function")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Niklas Cassel <nks@flawful.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Tue, 20 Oct 2015 13:55:21 +0000 (09:55 -0400)]
serial: fsl_lpuart: Fix earlycon support
Earlycon support for Freescale lpuart should only be enabled when
console support is enabled.
Fixes:
1d59b382f1c4 ("serial: fsl_lpuart: add earlycon support")
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon Arlott [Sun, 15 Nov 2015 16:14:32 +0000 (16:14 +0000)]
bcm63xx_uart: Use the device name when registering an interrupt
Use the device name when registering an interrupt so that multiple
ports don't all have the same interrupt name.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 8 Nov 2015 12:53:06 +0000 (07:53 -0500)]
tty: Fix direct use of tty buffer work
Recent abstraction of tty buffer work introduced api to manage
tty input kworker; use it.
Fixes:
e176058f0de5 ("tty: Abstract tty buffer work")
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 11 Nov 2015 13:03:54 +0000 (08:03 -0500)]
tty: Fix tty_send_xchar() lock order inversion
The correct lock order is atomic_write_lock => termios_rwsem, as
established by tty_write() => n_tty_write().
Fixes:
c274f6ef1c666 ("tty: Hold termios_rwsem for tcflow(TCIxxx)")
Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:41 +0000 (15:57 -0800)]
slub: mark the dangling ifdef #else of CONFIG_SLUB_DEBUG
The #ifdef of CONFIG_SLUB_DEBUG is located very far from the associated
#else. For readability mark it with a comment.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Fri, 20 Nov 2015 23:57:38 +0000 (15:57 -0800)]
slub: avoid irqoff/on in bulk allocation
Use the new function that can do allocation while interrupts are disabled.
Avoids irq on/off sequences.
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Fri, 20 Nov 2015 23:57:35 +0000 (15:57 -0800)]
slub: create new ___slab_alloc function that can be called with irqs disabled
Bulk alloc needs a function like that because it enables interrupts before
calling __slab_alloc which promptly disables them again using the expensive
local_irq_save().
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Fri, 20 Nov 2015 23:57:32 +0000 (15:57 -0800)]
mm: fix up sparse warning in gfpflags_allow_blocking
sparse says:
include/linux/gfp.h:274:26: warning: incorrect type in return expression (different base types)
include/linux/gfp.h:274:26: expected bool
include/linux/gfp.h:274:26: got restricted gfp_t
...add a forced cast to silence the warning.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Fri, 20 Nov 2015 23:57:30 +0000 (15:57 -0800)]
ocfs2: fix umask ignored issue
New created file's mode is not masked with umask, and this makes umask not
work for ocfs2 volume.
Fixes:
702e5bc ("ocfs2: use generic posix ACL infrastructure")
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Viresh Kumar [Fri, 20 Nov 2015 23:57:27 +0000 (15:57 -0800)]
PM/OPP: add entry in MAINTAINERS
Add entry for operating performance points into MAINTAINERS file. This
will also allow get_maintainers to list OPP stakeholders properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rafael Wysocki <rjw@rjwysocki.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaly Kuznetsov [Fri, 20 Nov 2015 23:57:24 +0000 (15:57 -0800)]
kernel/panic.c: turn off locks debug before releasing console lock
Commit
08d78658f393 ("panic: release stale console lock to always get the
logbuf printed out") introduced an unwanted bad unlock balance report when
panic() is called directly and not from OOPS (e.g. from out_of_memory()).
The difference is that in case of OOPS we disable locks debug in
oops_enter() and on direct panic call nobody does that.
Fixes:
08d78658f393 ("panic: release stale console lock to always get the logbuf printed out")
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Baoquan He <bhe@redhat.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Xie XiuQi <xiexiuqi@huawei.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Petr Mladek <pmladek@suse.cz>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Weinberger [Fri, 20 Nov 2015 23:57:21 +0000 (15:57 -0800)]
kernel/signal.c: unexport sigsuspend()
sigsuspend() is nowhere used except in signal.c itself, so we can mark it
static do not pollute the global namespace.
But this patch is more than a boring cleanup patch, it fixes a real issue
on UserModeLinux. UML has a special console driver to display ttys using
xterm, or other terminal emulators, on the host side. Vegard reported
that sometimes UML is unable to spawn a xterm and he's facing the
following warning:
WARNING: CPU: 0 PID: 908 at include/linux/thread_info.h:128 sigsuspend+0xab/0xc0()
It turned out that this warning makes absolutely no sense as the UML
xterm code calls sigsuspend() on the host side, at least it tries. But
as the kernel itself offers a sigsuspend() symbol the linker choose this
one instead of the glibc wrapper. Interestingly this code used to work
since ever but always blocked signals on the wrong side. Some recent
kernel change made the WARN_ON() trigger and uncovered the bug.
It is a wonderful example of how much works by chance on computers. :-)
Fixes:
68f3f16d9ad0f1 ("new helper: sigsuspend()")
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 20 Nov 2015 23:57:18 +0000 (15:57 -0800)]
kasan: fix kmemleak false-positive in kasan_module_alloc()
Kmemleak reports the following leak:
unreferenced object 0xfffffbfff41ea000 (size 20480):
comm "modprobe", pid 65199, jiffies
4298875551 (age 542.568s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff82354f5e>] kmemleak_alloc+0x4e/0xc0
[<
ffffffff8152e718>] __vmalloc_node_range+0x4b8/0x740
[<
ffffffff81574072>] kasan_module_alloc+0x72/0xc0
[<
ffffffff810efe68>] module_alloc+0x78/0xb0
[<
ffffffff812f6a24>] module_alloc_update_bounds+0x14/0x70
[<
ffffffff812f8184>] layout_and_allocate+0x16f4/0x3c90
[<
ffffffff812faa1f>] load_module+0x2ff/0x6690
[<
ffffffff813010b6>] SyS_finit_module+0x136/0x170
[<
ffffffff8239bbc9>] system_call_fastpath+0x16/0x1b
[<
ffffffffffffffff>] 0xffffffffffffffff
kasan_module_alloc() allocates shadow memory for module and frees it on
module unloading. It doesn't store the pointer to allocated shadow memory
because it could be calculated from the shadowed address, i.e.
kasan_mem_to_shadow(addr).
Since kmemleak cannot find pointer to allocated shadow, it thinks that
memory leaked.
Use kmemleak_ignore() to tell kmemleak that this is not a leak and shadow
memory doesn't contain any pointers.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Fri, 20 Nov 2015 23:57:15 +0000 (15:57 -0800)]
fat: fix fake_offset handling on error path
For the root directory, . and .. are faked (using dir_emit_dots()) and
ctx->pos is reset from 2 to 0.
A corrupted root directory could cause fat_get_entry() to fail, but
->iterate() (fat_readdir()) reports progress to the VFS (with ctx->pos
rewound to 0), so any following calls to ->iterate() continue to return
the same entries again and again.
The result is that userspace will never see the end of the directory,
causing e.g. 'ls' to hang in a getdents() loop.
[hirofumi@mail.parknet.co.jp: cleanup and make sure to correct fake_offset]
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Richard Weinberger <richard.weinberger@gmail.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Fri, 20 Nov 2015 23:57:13 +0000 (15:57 -0800)]
mm/hugetlbfs: fix bugs in fallocate hole punch of areas with holes
Hugh Dickins pointed out problems with the new hugetlbfs fallocate hole
punch code. These problems are in the routine remove_inode_hugepages and
mostly occur in the case where there are holes in the range of pages to be
removed. These holes could be the result of a previous hole punch or
simply sparse allocation. The current code could access pages outside the
specified range.
remove_inode_hugepages handles both hole punch and truncate operations.
Page index handling was fixed/cleaned up so that the loop index always
matches the page being processed. The code now only makes a single pass
through the range of pages as it was determined page faults could not race
with truncate. A cond_resched() was added after removing up to
PAGEVEC_SIZE pages.
Some totally unnecessary code in hugetlbfs_fallocate() that remained from
early development was also removed.
Tested with fallocate tests submitted here:
http://librelist.com/browser//libhugetlbfs/2015/6/25/patch-tests-add-tests-for-fallocate-system-call/
And, some ftruncate tests under development
Fixes:
b5cec28d36f5 ("hugetlbfs: truncate_hugepages() takes a range of pages")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: "Hillf Danton" <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org> [4.3]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yang Shi [Fri, 20 Nov 2015 23:57:10 +0000 (15:57 -0800)]
mm/page-writeback.c: initialize m_dirty to avoid compile warning
When building kernel with gcc 5.2, the below warning is raised:
mm/page-writeback.c: In function 'balance_dirty_pages.isra.10':
mm/page-writeback.c:1545:17: warning: 'm_dirty' may be used uninitialized in this function [-Wmaybe-uninitialized]
unsigned long m_dirty, m_thresh, m_bg_thresh;
The m_dirty{thresh, bg_thresh} are initialized in the block of "if
(mdtc)", so if mdts is null, they won't be initialized before being used.
Initialize m_dirty to zero, also initialize m_thresh and m_bg_thresh to
keep consistency.
They are used later by if condition: !mdtc || m_dirty <=
dirty_freerun_ceiling(m_thresh, m_bg_thresh)
If mdtc is null, dirty_freerun_ceiling will not be called at all, so the
initialization will not change any behavior other than just ceasing the
compile warning.
(akpm: the patch actually reduces .text size by ~20 bytes on gcc-4.x.y)
[akpm@linux-foundation.org: add comment]
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Fri, 20 Nov 2015 23:57:07 +0000 (15:57 -0800)]
various: fix pci_set_dma_mask return value checking
pci_set_dma_mask returns a negative errno value, not a bool like
pci_dma_supported. This of course was just a giant test for attention :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jongman Heo <jongman.heo@samsung.com>
Tested-by: Jongman Heo <jongman.heo@samsung.com> [pcnet32]
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jason J. Herne [Fri, 20 Nov 2015 23:57:04 +0000 (15:57 -0800)]
mm: loosen MADV_NOHUGEPAGE to enable Qemu postcopy on s390
MADV_NOHUGEPAGE processing is too restrictive. kvm already disables
hugepage but hugepage_madvise() takes the error path when we ask to turn
on the MADV_NOHUGEPAGE bit and the bit is already on. This causes Qemu's
new postcopy migration feature to fail on s390 because its first action is
to madvise the guest address space as NOHUGEPAGE. This patch modifies the
code so that the operation succeeds without error now.
For consistency reasons do the same for MADV_HUGEPAGE.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jerome Marchand [Fri, 20 Nov 2015 23:57:02 +0000 (15:57 -0800)]
mm: vmalloc: don't remove inexistent guard hole in remove_vm_area()
Commit
71394fe50146 ("mm: vmalloc: add flag preventing guard hole
allocation") missed a spot. Currently remove_vm_area() decreases vm->size
to "remove" the guard hole page, even when it isn't present. All but one
users just free the vm_struct rigth away and never access vm->size anyway.
Don't touch the size in remove_vm_area() and have __vunmap() use the
proper get_vm_area_size() helper.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 20 Nov 2015 23:56:59 +0000 (15:56 -0800)]
tools/vm/page-types.c: support KPF_IDLE
PageIdle is exported in include/uapi/linux/kernel-page-flags.h, so let's
make page-types.c tool handle it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Fri, 20 Nov 2015 23:56:56 +0000 (15:56 -0800)]
ncpfs: don't allow negative timeouts
This code causes a static checker warning because it's a user controlled
variable where we cap the upper bound but not the lower bound. Let's
return an -EINVAL for negative timeouts.
[akpm@linux-foundation.org: remove unneeded `else']
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jan Kara <jack@suse.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: David Howells <dhowells@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Baluta [Fri, 20 Nov 2015 23:56:53 +0000 (15:56 -0800)]
configfs: allow dynamic group creation
This patchset introduces IIO software triggers, offers a way of configuring
them via configfs and adds the IIO hrtimer based interrupt source to be used
with software triggers.
The architecture is now split in 3 parts, to remove all IIO trigger specific
parts from IIO configfs core:
(1) IIO configfs - creates the root of the IIO configfs subsys.
(2) IIO software triggers - software trigger implementation, dynamically
creating /config/iio/triggers group.
(3) IIO hrtimer trigger - is the first interrupt source for software triggers
(with syfs to follow). Each trigger type can implement its own set of
attributes.
Lockdep seems to be happy with the locking in configfs patch.
This patch (of 5):
We don't want to hardcode default groups at subsystem
creation time. We export:
* configfs_register_group
* configfs_unregister_group
to allow drivers to programatically create/destroy groups
later, after module init time.
This is needed for IIO configfs support.
(akpm: the other 4 patches to be merged via the IIO tree)
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Adriana Reus <adriana.reus@intel.com>
Cc: Cristina Opriceana <cristina.opriceana@gmail.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Moritz Fischer [Fri, 20 Nov 2015 23:56:51 +0000 (15:56 -0800)]
MAINTAINERS: add Moritz as reviewer for FPGA Manager Framework
Nominate myself as Reviewer.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rasmus Villemoes [Fri, 20 Nov 2015 23:56:48 +0000 (15:56 -0800)]
slab.h: sprinkle __assume_aligned attributes
The various allocators return aligned memory. Telling the compiler that
allows it to generate better code in many cases, for example when the
return value is immediately passed to memset().
Some code does become larger, but at least we win twice as much as we lose:
$ scripts/bloat-o-meter /tmp/vmlinux vmlinux
add/remove: 0/0 grow/shrink: 13/52 up/down: 995/-2140 (-1145)
An example of the different (and smaller) code can be seen in mm_alloc(). Before:
: 48 8d 78 08 lea 0x8(%rax),%rdi
: 48 89 c1 mov %rax,%rcx
: 48 89 c2 mov %rax,%rdx
: 48 c7 00 00 00 00 00 movq $0x0,(%rax)
: 48 c7 80 48 03 00 00 movq $0x0,0x348(%rax)
: 00 00 00 00
: 31 c0 xor %eax,%eax
: 48 83 e7 f8 and $0xfffffffffffffff8,%rdi
: 48 29 f9 sub %rdi,%rcx
: 81 c1 50 03 00 00 add $0x350,%ecx
: c1 e9 03 shr $0x3,%ecx
: f3 48 ab rep stos %rax,%es:(%rdi)
After:
: 48 89 c2 mov %rax,%rdx
: b9 6a 00 00 00 mov $0x6a,%ecx
: 31 c0 xor %eax,%eax
: 48 89 d7 mov %rdx,%rdi
: f3 48 ab rep stos %rax,%es:(%rdi)
So gcc's strategy is to do two possibly (but not really, of course)
unaligned stores to the first and last word, then do an aligned rep stos
covering the middle part with a little overlap. Maybe arches which do not
allow unaligned stores gain even more.
I don't know if gcc can actually make use of alignments greater than 8 for
anything, so one could probably drop the __assume_xyz_alignment macros and
just use __assume_aligned(8).
The increases in code size are mostly caused by gcc deciding to
opencode strlen() using the check-four-bytes-at-a-time trick when it
knows the buffer is sufficiently aligned (one function grew by 200
bytes). Now it turns out that many of these strlen() calls showing up
were in fact redundant, and they're gone from -next. Applying the two
patches to next-
20151001 bloat-o-meter instead says
add/remove: 0/0 grow/shrink: 6/52 up/down: 244/-2140 (-1896)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 20 Nov 2015 23:52:52 +0000 (15:52 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A few bugfixes and one PCI ID addition from I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: add Intel Lewisburg device IDs
i2c: fix wakeup irq parsing
i2c: xiic: Prevent concurrent running of the IRQ handler and __xiic_start_xfer()
i2c: Revert "i2c: xiic: Do not reset controller before every transfer"
i2c: imx: fix a compiling error
Linus Torvalds [Fri, 20 Nov 2015 23:47:27 +0000 (15:47 -0800)]
Merge tag '4.4-fix' of git://git.lwn.net/linux
Pull documentation fix from Jon Corbet:
"A single fix from Mauro for a 4.4 regression that would cause the docs
build to fail on systems with ancient Perl installations"
* tag '4.4-fix' of git://git.lwn.net/linux:
kernel-doc: Make it compatible with Perl versions below 5.12 again
Linus Torvalds [Fri, 20 Nov 2015 23:00:50 +0000 (15:00 -0800)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- A collection of crash and deadlock fixes for DAX that are also tagged
for -stable. We will look to re-enable DAX pmd mappings in 4.5, but
for now 4.4 and -stable should disable it by default.
- A fixup to ext2 and ext4 to mirror the same warning emitted by XFS
when mounting with "-o dax"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
block: protect rw_page against device teardown
mm, dax: fix DAX deadlocks (COW fault)
dax: disable pmd mappings
ext2, ext4: warn when mounting with dax enabled
Linus Torvalds [Fri, 20 Nov 2015 17:01:07 +0000 (09:01 -0800)]
Merge tag 'pm+acpi-4.4-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups (ACPI core, PM core, cpufreq, ACPI
EC driver, device properties) including three reverts of recent
intel_pstate driver commits due to a regression introduced by one of
them plus support for Atom Airmont cores in intel_pstate (which really
boils down to adding new frequency tables for Airmont) and additional
turbostat updates.
Specifics:
- Revert three recent intel_pstate driver commits one of which
introduced a regression and the remaining two depend on the
problematic one (Rafael Wysocki).
- Fix breakage related to the recently introduced ACPI _CCA object
support in the PCI DMA setup code (Suravee Suthikulpanit).
- Fix up the recently introduced ACPI CPPC support to only use the
hardware-reduced version of the PCCT structure as the only
architecture to support it (ARM64) will only use hardware-reduced
ACPI anyway (Ashwin Chaugule).
- Fix a cpufreq mediatek driver build problem (Arnd Bergmann).
- Fix the SMBus transaction handling implementation in the ACPI core
to avoid re-entrant calls to wait_event_timeout() which makes
intermittent boot stalls related to the Smart Battery Subsystem
initialization go away and revert a workaround of another problem
with the same underlying root cause (Chris Bainbridge).
- Fix the generic wakeup interrupts framework to avoid using invalid
IRQ numbers (Dmitry Torokhov).
- Remove a redundant check from the ACPI EC driver (Markus Elfring).
- Modify the intel_pstate driver so it can support more Atom flavors
than just one (Baytrail) and add support for Atom Airmont cores
(which require new freqnency tables) to it (Philippe Longepe).
- Clean up MSR-related symbols in turbostat (Len Brown)"
* tag 'pm+acpi-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI: Fix OF logic in pci_dma_configure()
Revert "Documentation: kernel_parameters for Intel P state driver"
cpufreq: mediatek: fix build error
cpufreq: intel_pstate: Add separate support for Airmont cores
cpufreq: intel_pstate: Replace BYT with ATOM
Revert "cpufreq: intel_pstate: Use ACPI perf configuration"
Revert "cpufreq: intel_pstate: Avoid calculation for max/min"
ACPI-EC: Drop unnecessary check made before calling acpi_ec_delete_query()
Revert "ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook"
ACPI / SMBus: Fix boot stalls / high CPU caused by reentrant code
PM / wakeirq: check that wake IRQ is valid before accepting it
ACPI / CPPC: Use h/w reduced version of the PCCT structure
x86: remove unused definition of MSR_NHM_PLATFORM_INFO
tools/power turbostat: use new name for MSR_PLATFORM_INFO
Linus Torvalds [Fri, 20 Nov 2015 16:20:04 +0000 (08:20 -0800)]
Merge tag 'powerpc-4.4-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixlet from Michael Ellerman:
"Wire up sys_mlock2()"
* tag 'powerpc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Wire up sys_mlock2()
Alexandra Yates [Thu, 5 Nov 2015 19:40:25 +0000 (11:40 -0800)]
i2c: i801: add Intel Lewisburg device IDs
Adding Intel codename Lewisburg platform device IDs for SMBus.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Grygorii Strashko [Thu, 12 Nov 2015 13:42:26 +0000 (15:42 +0200)]
i2c: fix wakeup irq parsing
This patch fixes obvious copy-past error in wake up irq parsing
code which leads to the fact that dev_pm_set_wake_irq() will
be called with wrong IRQ number when "wakeup" IRQ is not
defined in DT.
Fixes:
3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org> # v4.3
Lars-Peter Clausen [Mon, 16 Nov 2015 13:42:04 +0000 (14:42 +0100)]
i2c: xiic: Prevent concurrent running of the IRQ handler and __xiic_start_xfer()
Prior to commit
e6c9a037bc8a ("i2c: xiic: Remove the disabling of
interrupts") IRQs where disabled when the initial __xiic_start_xfer() was
called. After the commit the interrupt is enabled while the function is
running, this means it is possible for the interrupt to be triggered while
the function is still running. When this happens the internal data
structures get corrupted and undefined behavior can occur like the
following crash:
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 2040 Comm: i2cdetect Not tainted
4.0.0-02856-g047a308 #10956
Hardware name: Xilinx Zynq Platform
task:
ee0c9500 ti:
e99a2000 task.ti:
e99a2000
PC is at __xiic_start_xfer+0x6c4/0x7c8
LR is at __xiic_start_xfer+0x690/0x7c8
pc : [<
c02bbffc>] lr : [<
c02bbfc8>] psr:
800f0013
sp :
e99a3da8 ip :
00000000 fp :
00000000
r10:
00000001 r9 :
600f0013 r8 :
f0180000
r7 :
f0180000 r6 :
c064e444 r5 :
00000017 r4 :
ee031010
r3 :
00000000 r2 :
00000000 r1 :
600f0013 r0 :
0000000f
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control:
18c5387d Table:
29a5404a DAC:
00000015
Process i2cdetect (pid: 2040, stack limit = 0xe99a2210)
Stack: (0xe99a3da8 to 0xe99a4000)
3da0:
ee031010 00000000 00000001 ee031020 ee031224 c02bc5ec
3dc0:
ee34c604 00000000 ee0c9500 e99a3dcc e99a3dd0 e99a3dd0 e99a3dd8 c069f0e8
3de0:
00000000 ee031020 c064e100 ffff90bb e99a3e48 c02b6590 ee031020 00000001
3e00:
e99a3e48 ee031020 00000000 e99a3e63 00000001 c02b6ec4 00000000 00000000
3e20:
00000000 c02b7320 e99a3ef0 00000000 00000000 e99e3df0 00000000 00000000
3e40:
00000103 2814575f 0000003e c00a0000 e99a3e85 0001003e ee0c0000 e99a3e63
3e60:
eefd3578 c064e61c ee0c9500 c0041e04 0000056c e9a56db8 00006e5a b6f5c000
3e80:
ee0c9548 eefd0040 00000001 eefd3540 ee0c9500 eefd39a0 c064b540 ee0c9500
3ea0:
00000000 ee92b000 00000000 bef4862c ee34c600 e99ecdc0 00000720 00000003
3ec0:
e99a2000 00000000 00000000 c02b8b30 00000000 00000000 00000000 e99a3f24
3ee0:
b6e80000 00000000 00000000 c04257e8 00000000 e99a3f24 c02b8f08 00000703
3f00:
00000003 c02116bc ee935300 00000000 bef4862c ee34c600 e99ecdc0 c02b91f0
3f20:
e99ecdc0 00000720 bef4862c eeb725f8 e99ecdc0 c00c9e2c 00000003 00000003
3f40:
ee248dc0 00000000 ee248dc8 00000002 eeb7c1a8 00000000 00000000 c00bb360
3f60:
00000000 00000000 00000003 ee248dc0 bef4862c e99ecdc0 e99ecdc0 00000720
3f80:
00000003 e99a2000 00000000 c00c9f68 00000000 00000000 b6f22000 00000036
3fa0:
c000dfa4 c000de20 00000000 00000000 00000003 00000720 bef4862c bef4862c
3fc0:
00000000 00000000 b6f22000 00000036 00000000 00000000 b6f60000 00000000
3fe0:
00013040 bef48614 00008cab b6ecdbe6 400f0030 00000003 2f7fd821 2f7fdc21
[<
c02bbffc>] (__xiic_start_xfer) from [<
c02bc5ec>] (xiic_xfer+0x94/0x168)
[<
c02bc5ec>] (xiic_xfer) from [<
c02b6590>] (__i2c_transfer+0x4c/0x7c)
[<
c02b6590>] (__i2c_transfer) from [<
c02b6ec4>] (i2c_transfer+0x9c/0xc4)
[<
c02b6ec4>] (i2c_transfer) from [<
c02b7320>] (i2c_smbus_xfer+0x3a0/0x4ec)
[<
c02b7320>] (i2c_smbus_xfer) from [<
c02b8b30>] (i2cdev_ioctl_smbus+0xb0/0x214)
[<
c02b8b30>] (i2cdev_ioctl_smbus) from [<
c02b91f0>] (i2cdev_ioctl+0xa0/0x1d4)
[<
c02b91f0>] (i2cdev_ioctl) from [<
c00c9e2c>] (do_vfs_ioctl+0x4b0/0x5b8)
[<
c00c9e2c>] (do_vfs_ioctl) from [<
c00c9f68>] (SyS_ioctl+0x34/0x5c)
[<
c00c9f68>] (SyS_ioctl) from [<
c000de20>] (ret_fast_syscall+0x0/0x34)
Code:
e283300c e5843210 eafffe64 e5943210 (
e1d320b4)
The issue can easily be reproduced by performing I2C access under high
system load or IO load.
To fix the issue protect the invocation to __xiic_start_xfer() form
xiic_start_xfer() with the same lock that is used to protect the interrupt
handler.
Fixes:
e6c9a037bc8a ("i2c: xiic: Remove the disabling of interrupts")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lars-Peter Clausen [Mon, 16 Nov 2015 13:42:03 +0000 (14:42 +0100)]
i2c: Revert "i2c: xiic: Do not reset controller before every transfer"
Commit
d701667bb331 ("i2c: xiic: Do not reset controller before every
transfer") removed the reinitialization of the controller before the start
of each transfer. Apparently this change is not safe to make and the commit
results in random I2C bus failures.
An easy way to trigger the issue is to run i2cdetect.
Without the patch applied:
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- UU UU -- UU 3c -- -- UU
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
With the patch applied every other or so invocation:
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f
10: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f
20: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
30: -- -- -- -- -- -- -- -- UU UU -- UU 3c -- -- UU
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
So revert the commit for now.
Fixes:
d701667bb331 ("i2c: xiic: Do not reset controller before every transfer")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hou Zhiqiang [Tue, 17 Nov 2015 09:53:18 +0000 (17:53 +0800)]
i2c: imx: fix a compiling error
drivers/i2c/busses/i2c-imx.c:978:2: error: implicit declaration of
function ‘pinctrl_select_state’ [-Werror=implicit-function-declaration]
pinctrl_select_state(i2c_imx->pinctrl, i2c_imx->pinctrl_pins_gpio);
^
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Alban Bedel [Tue, 17 Nov 2015 20:52:00 +0000 (21:52 +0100)]
MIPS: ath79: Add a machine entry for booting OF machines
As I'm using a board with a broken old bootloader I hardcoded the
mips_machtype and did't notice that the machine entry was still
missing.
[ralf@linux-mips.org: Fixed spelling message noticed by Sergei Shtylyov
<sergei.shtylyov@cogentembedded.com>.]
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11503/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Alban Bedel [Tue, 17 Nov 2015 19:34:51 +0000 (20:34 +0100)]
MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
There is 2 registers that is 8 bytes long, not 4.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alexander Couzens <lynxis@fe80.eu>
Cc: Joel Porquet <joel@porquet.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11508/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Alban Bedel [Tue, 17 Nov 2015 08:40:07 +0000 (09:40 +0100)]
MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
The DDR control initialization needs to know the SoC type, however
ath79_detect_sys_type() was called after ath79_ddr_ctrl_init().
Reverse the order to fix the DDR control initialization on ar71xx and
ar934x.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
CC: stable@vger.kernel.org # v4.2+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11500/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Helge Deller [Fri, 20 Nov 2015 09:12:42 +0000 (10:12 +0100)]
parisc: Drop definition of start_thread_som for HP-UX SOM binaries
The definition of start_thread_som was planned to be used to execute
HP-UX SOM binaries. Since HP-UX compatibility was dropped with kernel 4.0
there is no need to carry it further.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 09:09:18 +0000 (10:09 +0100)]
parisc: Fix wrong comment regarding first pmd entry flags
The first pmd entry is marked with PxD_FLAG_ATTACHED instead of
_PAGE_GATEWAY.
Signed-off-by: Helge Deller <deller@gmx.de>