OSDN Git Service
Luiz Augusto von Dentz [Thu, 17 Feb 2022 21:10:38 +0000 (13:10 -0800)]
Bluetooth: hci_sync: Fix not using conn_timeout
When using hci_le_create_conn_sync it shall wait for the conn_timeout
since the connection complete may take longer than just 2 seconds.
Also fix the masking of HCI_EV_LE_ENHANCED_CONN_COMPLETE and
HCI_EV_LE_CONN_COMPLETE so they are never both set so we can predict
which one the controller will use in case of HCI_OP_LE_CREATE_CONN.
Fixes:
6cd29ec6ae5e3 ("Bluetooth: hci_sync: Wait for proper events when connecting LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Thu, 24 Feb 2022 15:11:47 +0000 (07:11 -0800)]
Bluetooth: hci_sync: Fix hci_update_accept_list_sync
hci_update_accept_list_sync is returning the filter based on the error
but that gets overwritten by hci_le_set_addr_resolution_enable_sync
return instead of using the actual result of the likes of
hci_le_add_accept_list_sync which was intended.
Fixes:
ad383c2c65a5b ("Bluetooth: hci_sync: Enable advertising when LL privacy is enabled")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Wang Qing [Tue, 15 Feb 2022 02:01:56 +0000 (18:01 -0800)]
Bluetooth: assign len after null check
len should be assigned after a null check
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Tue, 15 Feb 2022 01:59:38 +0000 (17:59 -0800)]
Bluetooth: Fix bt_skb_sendmmsg not allocating partial chunks
Since bt_skb_sendmmsg can be used with the likes of SOCK_STREAM it
shall return the partial chunks it could allocate instead of freeing
everything as otherwise it can cause problems like bellow.
Fixes:
81be03e026dc ("Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/d7206e12-1b99-c3be-84f4-df22af427ef5@molgen.mpg.de
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215594
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> (Nokia N9 (MeeGo/Harmattan)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Lin Ma [Wed, 16 Feb 2022 04:37:14 +0000 (12:37 +0800)]
Bluetooth: fix data races in smp_unregister(), smp_del_chan()
Previous commit
e04480920d1e ("Bluetooth: defer cleanup of resources
in hci_unregister_dev()") defers all destructive actions to
hci_release_dev() to prevent cocurrent problems like NPD, UAF.
However, there are still some exceptions that are ignored.
The smp_unregister() in hci_dev_close_sync() (previously in
hci_dev_do_close) will release resources like the sensitive channel
and the smp_dev objects. Consider the situations the device is detaching
or power down while the kernel is still operating on it, the following
data race could take place.
thread-A hci_dev_close_sync | thread-B read_local_oob_ext_data
|
hci_dev_unlock() |
... | hci_dev_lock()
if (hdev->smp_data) |
chan = hdev->smp_data |
| chan = hdev->smp_data (3)
|
hdev->smp_data = NULL (1) | if (!chan || !chan->data) (4)
... |
smp = chan->data | smp = chan->data
if (smp) |
chan->data = NULL (2) |
... |
kfree_sensitive(smp) |
| // dereference smp trigger UFA
That is, the objects hdev->smp_data and chan->data both suffer from the
data races. In a preempt-enable kernel, the above schedule (when (3) is
before (1) and (4) is before (2)) leads to UAF bugs. It can be
reproduced in the latest kernel and below is part of the report:
[ 49.097146] ================================================================
[ 49.097611] BUG: KASAN: use-after-free in smp_generate_oob+0x2dd/0x570
[ 49.097611] Read of size 8 at addr
ffff888006528360 by task generate_oob/155
[ 49.097611]
[ 49.097611] Call Trace:
[ 49.097611] <TASK>
[ 49.097611] dump_stack_lvl+0x34/0x44
[ 49.097611] print_address_description.constprop.0+0x1f/0x150
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] kasan_report.cold+0x7f/0x11b
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] smp_generate_oob+0x2dd/0x570
[ 49.097611] read_local_oob_ext_data+0x689/0xc30
[ 49.097611] ? hci_event_packet+0xc80/0xc80
[ 49.097611] ? sysvec_apic_timer_interrupt+0x9b/0xc0
[ 49.097611] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 49.097611] ? mgmt_init_hdev+0x1c/0x240
[ 49.097611] ? mgmt_init_hdev+0x28/0x240
[ 49.097611] hci_sock_sendmsg+0x1880/0x1e70
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] sock_sendmsg+0xdf/0x110
[ 49.097611] __sys_sendto+0x19e/0x270
[ 49.097611] ? __ia32_sys_getpeername+0xa0/0xa0
[ 49.097611] ? kernel_fpu_begin_mask+0x1c0/0x1c0
[ 49.097611] __x64_sys_sendto+0xd8/0x1b0
[ 49.097611] ? syscall_exit_to_user_mode+0x1d/0x40
[ 49.097611] do_syscall_64+0x3b/0x90
[ 49.097611] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 49.097611] RIP: 0033:0x7f5a59f51f64
...
[ 49.097611] RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00007f5a59f51f64
[ 49.097611] RDX:
0000000000000007 RSI:
00007f5a59d6ac70 RDI:
0000000000000006
[ 49.097611] RBP:
0000000000000000 R08:
0000000000000000 R09:
0000000000000000
[ 49.097611] R10:
0000000000000040 R11:
0000000000000246 R12:
00007ffec26916ee
[ 49.097611] R13:
00007ffec26916ef R14:
00007f5a59d6afc0 R15:
00007f5a59d6b700
To solve these data races, this patch places the smp_unregister()
function in the protected area by the hci_dev_lock(). That is, the
smp_unregister() function can not be concurrently executed when
operating functions (most of them are mgmt operations in mgmt.c) hold
the device lock.
This patch is tested with kernel LOCK DEBUGGING enabled. The price from
the extended holding time of the device lock is supposed to be low as the
smp_unregister() function is fairly short and efficient.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz [Fri, 4 Feb 2022 21:12:35 +0000 (13:12 -0800)]
Bluetooth: hci_core: Fix leaking sent_cmd skb
sent_cmd memory is not freed before freeing hci_dev causing it to leak
it contents.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Mauri Sandberg [Wed, 23 Feb 2022 14:23:37 +0000 (16:23 +0200)]
net: mv643xx_eth: process retval from of_get_mac_address
Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.
It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.
Fixes:
76723bca2802 ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 24 Feb 2022 03:41:08 +0000 (22:41 -0500)]
ping: remove pr_err from ping_lookup
As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().
Fixes:
35a79e64de29 ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mateusz Palczewski [Wed, 23 Feb 2022 17:53:47 +0000 (09:53 -0800)]
Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.
Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to configure TC map 0 for VSI 391
This reverts commit
3d2504663c41104b4359a15f35670cfa82de1bbf.
Fixes:
3d2504663c41 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Blakey [Wed, 23 Feb 2022 16:34:16 +0000 (18:34 +0200)]
openvswitch: Fix setting ipv6 fields causing hw csum failure
Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.
Fix this by updating skb->csum if available.
Trace resulted by ipv6 ttl dec and then sending packet
to conntrack [actions: set(ipv6(hlimit=63)),ct(zone=99)]:
[295241.900063] s_pf0vf2: hw csum failure
[295241.923191] Call Trace:
[295241.925728] <IRQ>
[295241.927836] dump_stack+0x5c/0x80
[295241.931240] __skb_checksum_complete+0xac/0xc0
[295241.935778] nf_conntrack_tcp_packet+0x398/0xba0 [nf_conntrack]
[295241.953030] nf_conntrack_in+0x498/0x5e0 [nf_conntrack]
[295241.958344] __ovs_ct_lookup+0xac/0x860 [openvswitch]
[295241.968532] ovs_ct_execute+0x4a7/0x7c0 [openvswitch]
[295241.979167] do_execute_actions+0x54a/0xaa0 [openvswitch]
[295242.001482] ovs_execute_actions+0x48/0x100 [openvswitch]
[295242.006966] ovs_dp_process_packet+0x96/0x1d0 [openvswitch]
[295242.012626] ovs_vport_receive+0x6c/0xc0 [openvswitch]
[295242.028763] netdev_frame_hook+0xc0/0x180 [openvswitch]
[295242.034074] __netif_receive_skb_core+0x2ca/0xcb0
[295242.047498] netif_receive_skb_internal+0x3e/0xc0
[295242.052291] napi_gro_receive+0xba/0xe0
[295242.056231] mlx5e_handle_rx_cqe_mpwrq_rep+0x12b/0x250 [mlx5_core]
[295242.062513] mlx5e_poll_rx_cq+0xa0f/0xa30 [mlx5_core]
[295242.067669] mlx5e_napi_poll+0xe1/0x6b0 [mlx5_core]
[295242.077958] net_rx_action+0x149/0x3b0
[295242.086762] __do_softirq+0xd7/0x2d6
[295242.090427] irq_exit+0xf7/0x100
[295242.093748] do_IRQ+0x7f/0xd0
[295242.096806] common_interrupt+0xf/0xf
[295242.100559] </IRQ>
[295242.102750] RIP: 0033:0x7f9022e88cbd
[295242.125246] RSP: 002b:
00007f9022282b20 EFLAGS:
00000246 ORIG_RAX:
ffffffffffffffda
[295242.132900] RAX:
0000000000000005 RBX:
0000000000000010 RCX:
0000000000000000
[295242.140120] RDX:
00007f9022282ba8 RSI:
00007f9022282a30 RDI:
00007f9014005c30
[295242.147337] RBP:
00007f9014014d60 R08:
0000000000000020 R09:
00007f90254a8340
[295242.154557] R10:
00007f9022282a28 R11:
0000000000000246 R12:
0000000000000000
[295242.161775] R13:
00007f902308c000 R14:
000000000000002b R15:
00007f9022b71f40
Fixes:
3fdbd1ce11e5 ("openvswitch: add ipv6 'set' action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Link: https://lore.kernel.org/r/20220223163416.24096-1-paulb@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Niels Dossche [Wed, 23 Feb 2022 13:19:56 +0000 (14:19 +0100)]
ipv6: prevent a possible race condition with lifetimes
valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fabio M. De Francesco [Wed, 23 Feb 2022 10:02:52 +0000 (11:02 +0100)]
net/smc: Use a mutex for locking "struct smc_pnettable"
smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).
read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.
Fix this bug by replacing the rwlock with a mutex.
Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes:
64e28b52c7a6 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Manish Chopra [Wed, 23 Feb 2022 08:57:20 +0000 (00:57 -0800)]
bnx2x: fix driver load from initrd
Commit
b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes:
b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marek Marczykowski-Górecki [Tue, 22 Feb 2022 00:18:17 +0000 (01:18 +0100)]
Revert "xen-netback: Check for hotplug-status existence before watching"
This reverts commit
2afeec08ab5c86ae21952151f726bfe184f6b23d.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/
afedd7cb-a291-e773-8b0d-
4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marek Marczykowski-Górecki [Tue, 22 Feb 2022 00:18:16 +0000 (01:18 +0100)]
Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
This reverts commit
1f2565780e9b7218cf92c7630130e82dcc0fe9c2.
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/
afedd7cb-a291-e773-8b0d-
4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 24 Feb 2022 04:30:00 +0000 (20:30 -0800)]
Merge tag 'mlx5-fixes-2022-02-23' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-02-22
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2022-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix VF min/max rate parameters interchange mistake
net/mlx5e: Add missing increment of count
net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
net/mlx5e: Add feature check for set fec counters
net/mlx5e: TC, Skip redundant ct clear actions
net/mlx5e: TC, Reject rules with forward and drop actions
net/mlx5e: TC, Reject rules with drop and modify hdr action
net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
net/mlx5: Fix possible deadlock on rule deletion
net/mlx5: Fix tc max supported prio for nic mode
net/mlx5: Fix wrong limitation of metadata match on ecpf
net/mlx5: Update log_max_qp value to be 17 at most
net/mlx5: DR, Fix the threshold that defines when pool sync is initiated
net/mlx5: DR, Don't allow match on IP w/o matching on full ethertype/ip_version
net/mlx5: DR, Fix slab-out-of-bounds in mlx5_cmd_dr_create_fte
net/mlx5: DR, Cache STE shadow memory
net/mlx5: Update the list of the PCI supported devices
====================
Link: https://lore.kernel.org/r/20220224001123.365265-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Mon, 21 Feb 2022 15:54:34 +0000 (17:54 +0200)]
net/mlx5e: Fix VF min/max rate parameters interchange mistake
The VF min and max rate were passed incorrectly and resulted in wrongly
interchanging them. Fix the order of parameters in
mlx5_esw_qos_set_vport_rate().
Fixes:
d7df09f5e7b4 ("net/mlx5: E-switch, Enable vport QoS on demand")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Lama Kayal [Mon, 21 Feb 2022 10:26:11 +0000 (12:26 +0200)]
net/mlx5e: Add missing increment of count
Add mistakenly missing increment of count variable when looping over
output buffer in mlx5e_self_test().
This resolves the issue of garbage values output when querying with self
test via ethtool.
before:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test
1768697188
Health Test
758528120
Loopback Test
3288687
after:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 0
Health Test 0
Loopback Test 0
Fixes:
7990b1b5e8bd ("net/mlx5e: loopback test is not supported in switchdev mode")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maor Dickman [Thu, 6 Jan 2022 12:46:24 +0000 (14:46 +0200)]
net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
Currently offload of rule on bareudp device require tunnel key
in order to match on mpls fields and without it the mpls fields
are ignored, this is incorrect due to the fact udp tunnel doesn't
have key to match on.
Fix by returning error in case flow is matching on tunnel key.
Fixes:
72046a91d134 ("net/mlx5e: Allow to match on mpls parameters")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maor Dickman [Thu, 6 Jan 2022 12:10:18 +0000 (14:10 +0200)]
net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
Currently the MPLSoUDP encap builds the MPLS header using encap action
information (tunnel id, ttl and tos) instead of the MPLS action
information (label, ttl, tc and bos) which is wrong.
Fix by storing the MPLS action information during the flow action
parse and later using it to create the encap MPLS header.
Fixes:
f828ca6a2fb6 ("net/mlx5e: Add support for hw encapsulation of MPLS over UDP")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Lama Kayal [Tue, 1 Feb 2022 09:24:41 +0000 (11:24 +0200)]
net/mlx5e: Add feature check for set fec counters
Fec counters support is checked via the PCAM feature_cap_mask,
bit 0: PPCNT_counter_group_Phy_statistical_counter_group.
Add feature check to avoid faulty behavior.
Fixes:
0a1498ebfa55 ("net/mlx5e: Expose FEC counters via ethtool")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Roi Dayan [Thu, 3 Feb 2022 07:42:19 +0000 (09:42 +0200)]
net/mlx5e: TC, Skip redundant ct clear actions
Offload of ct clear action is just resetting the reg_c register.
It's done by allocating modify hdr resources which is limited.
Doing it multiple times is redundant and wasting modify hdr resources
and if resources depleted the driver will fail offloading the rule.
Ignore redundant ct clear actions after the first one.
Fixes:
806401c20a0f ("net/mlx5e: CT, Fix multiple allocations and memleak of mod acts")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Roi Dayan [Mon, 17 Jan 2022 13:00:30 +0000 (15:00 +0200)]
net/mlx5e: TC, Reject rules with forward and drop actions
Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.
Fixes:
03a9d11e6eeb ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Roi Dayan [Tue, 4 Jan 2022 08:38:02 +0000 (10:38 +0200)]
net/mlx5e: TC, Reject rules with drop and modify hdr action
This kind of action is not supported by firmware and generates a
syndrome.
kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)
Fixes:
d7e75a325cb2 ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tariq Toukan [Mon, 31 Jan 2022 08:26:19 +0000 (10:26 +0200)]
net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.
Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.
Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.
Fixes:
1182f3659357 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Gal Pressman [Wed, 2 Feb 2022 14:07:21 +0000 (16:07 +0200)]
net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.
Fixes:
bb64143eee8c ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maor Gottlieb [Mon, 24 Jan 2022 19:25:04 +0000 (21:25 +0200)]
net/mlx5: Fix possible deadlock on rule deletion
Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.
Fixes:
465e7baab6d9 ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Chris Mi [Tue, 14 Dec 2021 01:52:53 +0000 (03:52 +0200)]
net/mlx5: Fix tc max supported prio for nic mode
Only prio 1 is supported if firmware doesn't support ignore flow
level for nic mode. The offending commit removed the check wrongly.
Add it back.
Fixes:
9a99c8f1253a ("net/mlx5e: E-Switch, Offload all chain 0 priorities when modify header and forward action is not supported")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Ariel Levkovich [Fri, 28 Jan 2022 23:39:24 +0000 (01:39 +0200)]
net/mlx5: Fix wrong limitation of metadata match on ecpf
Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.
Fixes:
92ab1eb392c6 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Maher Sanalla [Wed, 16 Feb 2022 09:01:04 +0000 (11:01 +0200)]
net/mlx5: Update log_max_qp value to be 17 at most
Currently, log_max_qp value is dependent on what FW reports as its max capability.
In reality, due to a bug, some FWs report a value greater than 17, even though they
don't support log_max_qp > 17.
This FW issue led the driver to exhaust memory on startup.
Thus, log_max_qp value is set to be no more than 17 regardless
of what FW reports, as it was before the cited commit.
Fixes:
f79a609ea6bf ("net/mlx5: Update log_max_qp value to FW max capability")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Yevgeny Kliteynik [Wed, 29 Dec 2021 20:22:05 +0000 (22:22 +0200)]
net/mlx5: DR, Fix the threshold that defines when pool sync is initiated
When deciding whether to start syncing and actually free all the "hot"
ICM chunks, we need to consider the type of the ICM chunks that we're
dealing with. For instance, the amount of available ICM for MODIFY_ACTION
is significantly lower than the usual STE ICM, so the threshold should
account for that - otherwise we can deplete MODIFY_ACTION memory just by
creating and deleting the same modify header action in a continuous loop.
This patch replaces the hard-coded threshold with a dynamic value.
Fixes:
1c58651412bb ("net/mlx5: DR, ICM memory pools sync optimization")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Yevgeny Kliteynik [Thu, 13 Jan 2022 12:52:48 +0000 (14:52 +0200)]
net/mlx5: DR, Don't allow match on IP w/o matching on full ethertype/ip_version
Currently SMFS allows adding rule with matching on src/dst IP w/o matching
on full ethertype or ip_version, which is not supported by HW.
This patch fixes this issue and adds the check as it is done in DMFS.
Fixes:
26d688e33f88 ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Yevgeny Kliteynik [Tue, 11 Jan 2022 01:00:03 +0000 (03:00 +0200)]
net/mlx5: DR, Fix slab-out-of-bounds in mlx5_cmd_dr_create_fte
When adding a rule with 32 destinations, we hit the following out-of-band
access issue:
BUG: KASAN: slab-out-of-bounds in mlx5_cmd_dr_create_fte+0x18ee/0x1e70
This patch fixes the issue by both increasing the allocated buffers to
accommodate for the needed actions and by checking the number of actions
to prevent this issue when a rule with too many actions is provided.
Fixes:
1ffd498901c1 ("net/mlx5: DR, Increase supported num of actions to 32")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Yevgeny Kliteynik [Thu, 23 Dec 2021 23:07:30 +0000 (01:07 +0200)]
net/mlx5: DR, Cache STE shadow memory
During rule insertion on each ICM memory chunk we also allocate shadow memory
used for management. This includes the hw_ste, dr_ste and miss list per entry.
Since the scale of these allocations is large we noticed a performance hiccup
that happens once malloc and free are stressed.
In extreme usecases when ~1M chunks are freed at once, it might take up to 40
seconds to complete this, up to the point the kernel sees this as self-detected
stall on CPU:
rcu: INFO: rcu_sched self-detected stall on CPU
To resolve this we will increase the reuse of shadow memory.
Doing this we see that a time in the aforementioned usecase dropped from ~40
seconds to ~8-10 seconds.
Fixes:
29cf8febd185 ("net/mlx5: DR, ICM pool memory allocator")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Meir Lichtinger [Mon, 10 Jan 2022 08:14:41 +0000 (10:14 +0200)]
net/mlx5: Update the list of the PCI supported devices
Add the upcoming BlueField-4 and ConnectX-8 device IDs.
Fixes:
2e9d3e83ab82 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
David S. Miller [Wed, 23 Feb 2022 12:50:19 +0000 (12:50 +0000)]
Merge branch 'ftgmac100-fixes'
Heyi Guo says:
====================
drivers/net/ftgmac100: fix occasional DHCP failure
This patch set is to fix the issues discussed in the mail thread:
https://lore.kernel.org/netdev/
51f5b7a7-330f-6b3c-253d-
10e45cdb6805@linux.alibaba.com/
and follows the advice from Andrew Lunn.
The first 2 patches refactors the code to enable adjust_link calling reset
function directly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heyi Guo [Wed, 23 Feb 2022 03:14:36 +0000 (11:14 +0800)]
drivers/net/ftgmac100: fix DHCP potential failure with systemd
DHCP failures were observed with systemd 247.6. The issue could be
reproduced by rebooting Aspeed 2600 and then running ifconfig ethX
down/up.
It is caused by below procedures in the driver:
1. ftgmac100_open() enables net interface and call phy_start()
2. When PHY is link up, it calls netif_carrier_on() and then
adjust_link callback
3. ftgmac100_adjust_link() will schedule the reset task
4. ftgmac100_reset_task() will then reset the MAC in another schedule
After step 2, systemd will be notified to send DHCP discover packet,
while the packet might be corrupted by MAC reset operation in step 4.
Call ftgmac100_reset() directly instead of scheduling task to fix the
issue.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heyi Guo [Wed, 23 Feb 2022 03:14:35 +0000 (11:14 +0800)]
drivers/net/ftgmac100: adjust code place for function call dependency
This is to prepare for ftgmac100_adjust_link() to call
ftgmac100_reset() directly. Only code places are changed.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heyi Guo [Wed, 23 Feb 2022 03:14:34 +0000 (11:14 +0800)]
drivers/net/ftgmac100: refactor ftgmac100_reset_task to enable direct function call
This is to prepare for ftgmac100_adjust_link() to call reset function
directly, instead of task schedule.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wan Jiabing [Wed, 23 Feb 2022 02:34:19 +0000 (10:34 +0800)]
net: sched: avoid newline at end of message in NL_SET_ERR_MSG_MOD
Fix following coccicheck warning:
./net/sched/act_api.c:277:7-49: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alvin Šipraga [Tue, 22 Feb 2022 16:14:08 +0000 (17:14 +0100)]
MAINTAINERS: add myself as co-maintainer for Realtek DSA switch drivers
Adding myself (Alvin Šipraga) as another maintainer for the Realtek DSA
switch drivers. I intend to help Linus out with reviewing and testing
changes to these drivers, particularly the rtl8365mb driver which I
authored and have hardware access to.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 22 Feb 2022 13:43:12 +0000 (16:43 +0300)]
tipc: Fix end of loop tests for list_for_each_entry()
These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer. In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {". That's going to work most of the time,
but there is a potential for those to be equal.
Fixes:
1593123a6a49 ("tipc: add name table dump to new netlink api")
Fixes:
1a1a143daf84 ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 22 Feb 2022 13:42:51 +0000 (16:42 +0300)]
udp_tunnel: Fix end of loop test in udp_tunnel_nic_unregister()
This test is checking if we exited the list via break or not. However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct. It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.
Fixes:
74cc6d182d03 ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Tue, 22 Feb 2022 09:47:42 +0000 (10:47 +0100)]
vhost/vsock: don't check owner in vhost_vsock_stop() while releasing
vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.
vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.
Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.
When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.
Fixes:
433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by: syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sukadev Bhattiprolu [Mon, 21 Feb 2022 21:05:45 +0000 (15:05 -0600)]
ibmvnic: schedule failover only if vioctl fails
If client is unable to initiate a failover reset via H_VIOCTL hcall, then
it should schedule a failover reset as a last resort. Otherwise, there is
no need to do a last resort.
Fixes:
334c42414729 ("ibmvnic: improve failover sysfs entry")
Reported-by: Cris Forno <cforno12@outlook.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221210545.115283-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alvin Šipraga [Mon, 21 Feb 2022 20:35:38 +0000 (21:35 +0100)]
net: dsa: fix panic when removing unoffloaded port from bridge
If a bridged port is not offloaded to the hardware - either because the
underlying driver does not implement the port_bridge_{join,leave} ops,
or because the operation failed - then its dp->bridge pointer will be
NULL when dsa_port_bridge_leave() is called. Avoid dereferncing NULL.
This fixes the following splat when removing a port from a bridge:
Unable to handle kernel access to user memory outside uaccess routines at virtual address
0000000000000000
Internal error: Oops:
96000004 [#1] PREEMPT_RT SMP
CPU: 3 PID: 1119 Comm: brctl Tainted: G O 5.17.0-rc4-rt4 #1
Call trace:
dsa_port_bridge_leave+0x8c/0x1e4
dsa_slave_changeupper+0x40/0x170
dsa_slave_netdevice_event+0x494/0x4d4
notifier_call_chain+0x80/0xe0
raw_notifier_call_chain+0x1c/0x24
call_netdevice_notifiers_info+0x5c/0xac
__netdev_upper_dev_unlink+0xa4/0x200
netdev_upper_dev_unlink+0x38/0x60
del_nbp+0x1b0/0x300
br_del_if+0x38/0x114
add_del_if+0x60/0xa0
br_ioctl_stub+0x128/0x2dc
br_ioctl_call+0x68/0xb0
dev_ifsioc+0x390/0x554
dev_ioctl+0x128/0x400
sock_do_ioctl+0xb4/0xf4
sock_ioctl+0x12c/0x4e0
__arm64_sys_ioctl+0xa8/0xf0
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x28/0x84
el0_svc+0x1c/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x17c/0x180
Code:
f9402f00 f0002261 f9401302 913cc021 (
a9401404)
---[ end trace
0000000000000000 ]---
Fixes:
d3eed0e57d5d ("net: dsa: keep the bridge_dev and bridge_num as part of the same structure")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220221203539.310690-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Sun, 20 Feb 2022 15:40:52 +0000 (07:40 -0800)]
net: __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor friends
Whenever one of these functions pull all data from an skb in a frag_list,
use consume_skb() instead of kfree_skb() to avoid polluting drop
monitoring.
Fixes:
6fa01ccd8830 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220220154052.1308469-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David S. Miller [Tue, 22 Feb 2022 11:00:51 +0000 (11:00 +0000)]
Merge git://git./linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is fixing up the use without proper initialization in patch 5/5
-o-
Hi,
The following patchset contains Netfilter fixes for net:
1) Missing #ifdef CONFIG_IP6_NF_IPTABLES in recent xt_socket fix.
2) Fix incorrect flow action array size in nf_tables.
3) Unregister flowtable hooks from netns exit path.
4) Fix missing limit object release, from Florian Westphal.
5) Memleak in nf_tables object update path, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Feb 2022 12:31:49 +0000 (13:31 +0100)]
netfilter: nf_tables: fix memory leak during stateful obj update
stateful objects can be updated from the control plane.
The transaction logic allocates a temporary object for this purpose.
The ->init function was called for this object, so plain kfree() leaks
resources. We must call ->destroy function of the object.
nft_obj_destroy does this, but it also decrements the module refcount,
but the update path doesn't increment it.
To avoid special-casing the update object release, do module_get for
the update case too and release it via nft_obj_destroy().
Fixes:
d62d0ba97b58 ("netfilter: nf_tables: Introduce stateful object update operation")
Cc: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Fri, 18 Feb 2022 12:17:05 +0000 (13:17 +0100)]
netfilter: nft_limit: fix stateful object memory leak
We need to provide a destroy callback to release the extra fields.
Fixes:
3b9e2ea6c11b ("netfilter: nft_limit: move stateful fields out of expression data")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Fri, 18 Feb 2022 11:45:32 +0000 (12:45 +0100)]
netfilter: nf_tables: unregister flowtable hooks on netns exit
Unregister flowtable hooks before they are releases via
nf_tables_flowtable_destroy() otherwise hook core reports UAF.
BUG: KASAN: use-after-free in nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
Read of size 4 at addr
ffff8880736f7438 by task syz-executor579/3666
CPU: 0 PID: 3666 Comm: syz-executor579 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
__dump_stack lib/dump_stack.c:88 [inline] lib/dump_stack.c:106
dump_stack_lvl+0x1dc/0x2d8 lib/dump_stack.c:106 lib/dump_stack.c:106
print_address_description+0x65/0x380 mm/kasan/report.c:247 mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
__kasan_report mm/kasan/report.c:433 [inline] mm/kasan/report.c:450
kasan_report+0x19a/0x1f0 mm/kasan/report.c:450 mm/kasan/report.c:450
nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
__nf_register_net_hook+0x27e/0x8d0 net/netfilter/core.c:429 net/netfilter/core.c:429
nf_register_net_hook+0xaa/0x180 net/netfilter/core.c:571 net/netfilter/core.c:571
nft_register_flowtable_net_hooks+0x3c5/0x730 net/netfilter/nf_tables_api.c:7232 net/netfilter/nf_tables_api.c:7232
nf_tables_newflowtable+0x2022/0x2cf0 net/netfilter/nf_tables_api.c:7430 net/netfilter/nf_tables_api.c:7430
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline]
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline] net/netfilter/nfnetlink.c:652
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] net/netfilter/nfnetlink.c:652
nfnetlink_rcv+0x10e6/0x2550 net/netfilter/nfnetlink.c:652 net/netfilter/nfnetlink.c:652
__nft_release_hook() calls nft_unregister_flowtable_net_hooks() which
only unregisters the hooks, then after RCU grace period, it is
guaranteed that no packets add new entries to the flowtable (no flow
offload rules and flowtable hooks are reachable from packet path), so it
is safe to call nf_flow_table_free() which cleans up the remaining
entries from the flowtable (both software and hardware) and it unbinds
the flow_block.
Fixes:
ff4bf2f42a40 ("netfilter: nf_tables: add nft_unregister_flowtable_hook()")
Reported-by: syzbot+e918523f77e62790d6d9@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Baruch Siach [Mon, 21 Feb 2022 11:45:57 +0000 (13:45 +0200)]
net: mdio-ipq4019: add delay after clock enable
Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.
PHY detect failure started to show after commit
7590fc6f80ac ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.
10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.
Fixes:
23a890d493e3 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tao Liu [Fri, 18 Feb 2022 14:35:24 +0000 (22:35 +0800)]
gso: do not skip outer ip header in case of ipip and net_failover
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Call Trace:
tcp4_gso_segment ------> return NULL
inet_gso_segment ------> inner iph, network_header points to
ipip_gso_segment
inet_gso_segment ------> outer iph
skb_mac_gso_segment
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
Call Trace:
inet_gso_segment ------> inner iph, outer iph is skipped
skb_mac_gso_segment
__skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
__qdisc_run
__dev_queue_xmit ------> virtio_net
dev_hard_start_xmit
__dev_queue_xmit ------> net_failover
ip_finish_output2
ip_output
iptunnel_xmit
ip_tunnel_xmit
ipip_tunnel_xmit ------> ipip
dev_hard_start_xmit
__dev_queue_xmit
ip_finish_output2
ip_output
ip_forward
ip_rcv
__netif_receive_skb_one_core
netif_receive_skb_internal
napi_gro_receive
receive_buf
virtnet_poll
net_rx_action
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes:
cb32f511a70b ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 20 Feb 2022 13:47:15 +0000 (13:47 +0000)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes
This series contains bug fixes for FEC reporting, ethtool self test,
multicast setup, devlink health reporting and live patching, and
a firmware response timeout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Sun, 20 Feb 2022 09:05:53 +0000 (04:05 -0500)]
bnxt_en: Fix devlink fw_activate
To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.
The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:
1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.
Fix the code to handle these scenarios during devlink "fw_activate".
To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
Fixes:
3c4153394e2c ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 20 Feb 2022 09:05:52 +0000 (04:05 -0500)]
bnxt_en: Increase firmware message response DMA wait time
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes:
3c8c20db769c ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Sun, 20 Feb 2022 09:05:51 +0000 (04:05 -0500)]
bnxt_en: Restore the resets_reliable flag in bnxt_open()
During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped. This is correct because a FW reset during
ifdown will clear these register mappings. If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.
But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.
Fixes:
8cc95ceb7087 ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavan Chebbi [Sun, 20 Feb 2022 09:05:50 +0000 (04:05 -0500)]
bnxt_en: Fix incorrect multicast rx mask setting when not requested
We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked. Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.
Fixes:
7d2837dd7a32 ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 20 Feb 2022 09:05:49 +0000 (04:05 -0500)]
bnxt_en: Fix occasional ethtool -t loopback test failures
In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes:
91725d89b97a ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 20 Feb 2022 09:05:48 +0000 (04:05 -0500)]
bnxt_en: Fix offline ethtool selftest with RDMA enabled
For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.
The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.
Fixes:
55fd0cf320c3 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Sun, 20 Feb 2022 09:05:47 +0000 (04:05 -0500)]
bnxt_en: Fix active FEC reporting to ethtool
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes:
8b2775890ad8 ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Thu, 17 Feb 2022 22:41:20 +0000 (23:41 +0100)]
netfilter: nf_tables_offload: incorrect flow offload action array size
immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.
fwd and dup expression need to allocate one slot, this is missing.
Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.
Fixes:
be2861dc36d7 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Vladimir Oltean [Fri, 18 Feb 2022 12:13:02 +0000 (14:13 +0200)]
net: dsa: avoid call to __dev_set_promiscuity() while rtnl_mutex isn't held
If the DSA master doesn't support IFF_UNICAST_FLT, then the following
call path is possible:
dsa_slave_switchdev_event_work
-> dsa_port_host_fdb_add
-> dev_uc_add
-> __dev_set_rx_mode
-> __dev_set_promiscuity
Since the blamed commit, dsa_slave_switchdev_event_work() no longer
holds rtnl_lock(), which triggers the ASSERT_RTNL() from
__dev_set_promiscuity().
Taking rtnl_lock() around dev_uc_add() is impossible, because all the
code paths that call dsa_flush_workqueue() do so from contexts where the
rtnl_mutex is already held - so this would lead to an instant deadlock.
dev_uc_add() in itself doesn't require the rtnl_mutex for protection.
There is this comment in __dev_set_rx_mode() which assumes so:
/* Unicast addresses changes may only happen under the rtnl,
* therefore calling __dev_set_promiscuity here is safe.
*/
but it is from commit
4417da668c00 ("[NET]: dev: secondary unicast
address support") dated June 2007, and in the meantime, commit
f1f28aa3510d ("netdev: Add addr_list_lock to struct net_device."), dated
July 2008, has added &dev->addr_list_lock to protect this instead of the
global rtnl_mutex.
Nonetheless, __dev_set_promiscuity() does assume rtnl_mutex protection,
but it is the uncommon path of what we typically expect dev_uc_add()
to do. So since only the uncommon path requires rtnl_lock(), just check
ahead of time whether dev_uc_add() would result into a call to
__dev_set_promiscuity(), and handle that condition separately.
DSA already configures the master interface to be promiscuous if the
tagger requires this. We can extend this to also cover the case where
the master doesn't handle dev_uc_add() (doesn't support IFF_UNICAST_FLT),
and on the premise that we'd end up making it promiscuous during
operation anyway, either if a DSA slave has a non-inherited MAC address,
or if the bridge notifies local FDB entries for its own MAC address, the
address of a station learned on a foreign port, etc.
Fixes:
0faf890fc519 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Svenning Sørensen [Fri, 18 Feb 2022 11:27:01 +0000 (11:27 +0000)]
net: dsa: microchip: fix bridging with more than two member ports
Commit
b3612ccdf284 ("net: dsa: microchip: implement multi-bridge support")
plugged a packet leak between ports that were members of different bridges.
Unfortunately, this broke another use case, namely that of more than two
ports that are members of the same bridge.
After that commit, when a port is added to a bridge, hardware bridging
between other member ports of that bridge will be cleared, preventing
packet exchange between them.
Fix by ensuring that the Port VLAN Membership bitmap includes any existing
ports in the bridge, not just the port being added.
Fixes:
b3612ccdf284 ("net: dsa: microchip: implement multi-bridge support")
Signed-off-by: Svenning Sørensen <sss@secomea.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe Leroy [Thu, 17 Feb 2022 13:35:49 +0000 (14:35 +0100)]
net: Force inlining of checksum functions in net/checksum.h
All functions defined as static inline in net/checksum.h are
meant to be inlined for performance reason.
But since commit
ac7c3e4ff401 ("compiler: enable
CONFIG_OPTIMIZE_INLINING forcibly") the compiler is allowed to
uninline functions when it wants.
Fair enough in the general case, but for tiny performance critical
checksum helpers that's counter-productive.
The problem mainly arises when selecting CONFIG_CC_OPTIMISE_FOR_SIZE,
Those helpers being 'static inline' in header files you suddenly find
them duplicated many times in the resulting vmlinux.
Here is a typical exemple when building powerpc pmac32_defconfig
with CONFIG_CC_OPTIMISE_FOR_SIZE. csum_sub() appears 4 times:
c04a23cc <csum_sub>:
c04a23cc: 7c 84 20 f8 not r4,r4
c04a23d0: 7c 63 20 14 addc r3,r3,r4
c04a23d4: 7c 63 01 94 addze r3,r3
c04a23d8: 4e 80 00 20 blr
...
c04a2ce8: 4b ff f6 e5 bl
c04a23cc <csum_sub>
...
c04a2d2c: 4b ff f6 a1 bl
c04a23cc <csum_sub>
...
c04a2d54: 4b ff f6 79 bl
c04a23cc <csum_sub>
...
c04a754c <csum_sub>:
c04a754c: 7c 84 20 f8 not r4,r4
c04a7550: 7c 63 20 14 addc r3,r3,r4
c04a7554: 7c 63 01 94 addze r3,r3
c04a7558: 4e 80 00 20 blr
...
c04ac930: 4b ff ac 1d bl
c04a754c <csum_sub>
...
c04ad264: 4b ff a2 e9 bl
c04a754c <csum_sub>
...
c04e3b08 <csum_sub>:
c04e3b08: 7c 84 20 f8 not r4,r4
c04e3b0c: 7c 63 20 14 addc r3,r3,r4
c04e3b10: 7c 63 01 94 addze r3,r3
c04e3b14: 4e 80 00 20 blr
...
c04e5788: 4b ff e3 81 bl
c04e3b08 <csum_sub>
...
c04e65c8: 4b ff d5 41 bl
c04e3b08 <csum_sub>
...
c0512d34 <csum_sub>:
c0512d34: 7c 84 20 f8 not r4,r4
c0512d38: 7c 63 20 14 addc r3,r3,r4
c0512d3c: 7c 63 01 94 addze r3,r3
c0512d40: 4e 80 00 20 blr
...
c0512dfc: 4b ff ff 39 bl
c0512d34 <csum_sub>
...
c05138bc: 4b ff f4 79 bl
c0512d34 <csum_sub>
...
Restore the expected behaviour by using __always_inline for all
functions defined in net/checksum.h
vmlinux size is even reduced by 256 bytes with this patch:
text data bss dec hex filename
6980022 2515362 194384
9689768 93daa8 vmlinux.before
6979862 2515266 194384
9689512 93d9a8 vmlinux.now
Fixes:
ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 19 Feb 2022 12:35:20 +0000 (12:35 +0000)]
Merge branch '100GbE' of git://git./linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-18
This series contains updates to ice driver only.
Wojciech fixes protocol matching for slow-path switchdev so that all
packets are correctly redirected.
Michal removes accidental unconditional setting of l4 port filtering
flag.
Jake adds locking to protect VF reset and removal to fix various issues
that can be encountered when they race with each other.
Tom Rix propagates an error and initializes a struct to resolve reported
Clang issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 19 Feb 2022 12:28:01 +0000 (12:28 +0000)]
Merge branch 'mptcp-fixes'
Mat Martineau says:
====================
mptcp: Fix address advertisement races and stabilize tests
Patches 1, 2, and 7 modify two self tests to give consistent, accurate
results by fixing timing issues and accounting for syncookie behavior.
Paches 3-6 fix two races in overlapping address advertisement send and
receive. Associated self tests are updated, including addition of two
MIBs to enable testing and tracking dropped address events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 18 Feb 2022 21:35:44 +0000 (13:35 -0800)]
selftests: mptcp: be more conservative with cookie MPJ limits
Since commit
2843ff6f36db ("mptcp: remote addresses fullmesh"), an
MPTCP client can attempt creating multiple MPJ subflow simultaneusly.
In such scenario the server, when syncookies are enabled, could end-up
accepting incoming MPJ syn even above the configured subflow limit, as
the such limit can be enforced in a reliable way only after the subflow
creation. In case of syncookie, only after the 3rd ack reception.
As a consequence the related self-tests case sporadically fails, as it
verify that the server always accept the expected number of MPJ syn.
Address the issues relaxing the MPJ syn number constrain. Note that the
check on the accepted number of MPJ 3rd ack still remains intact.
Fixes:
2843ff6f36db ("mptcp: remote addresses fullmesh")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 18 Feb 2022 21:35:43 +0000 (13:35 -0800)]
selftests: mptcp: more robust signal race test
The in kernel MPTCP PM implementation can process a single
incoming add address option at any given time. In the
mentioned test the server can surpass such limit. Let the
setup cope with that allowing a faster add_addr retransmission.
Fixes:
a88c9e496937 ("mptcp: do not block subflows creation on errors")
Fixes:
f7efc7771eac ("mptcp: drop argument port from mptcp_pm_announce_addr")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/254
Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 18 Feb 2022 21:35:42 +0000 (13:35 -0800)]
mptcp: add mibs counter for ignored incoming options
The MPTCP in kernel path manager has some constraints on incoming
addresses announce processing, so that in edge scenarios it can
end-up dropping (ignoring) some of such announces.
The above is not very limiting in practice since such scenarios are
very uncommon and MPTCP will recover due to ADD_ADDR retransmissions.
This patch adds a few MIB counters to account for such drop events
to allow easier introspection of the critical scenarios.
Fixes:
f7efc7771eac ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 18 Feb 2022 21:35:41 +0000 (13:35 -0800)]
mptcp: fix race in incoming ADD_ADDR option processing
If an MPTCP endpoint received multiple consecutive incoming
ADD_ADDR options, mptcp_pm_add_addr_received() can overwrite
the current remote address value after the PM lock is released
in mptcp_pm_nl_add_addr_received() and before such address
is echoed.
Fix the issue caching the remote address value a little earlier
and always using the cached value after releasing the PM lock.
Fixes:
f7efc7771eac ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 18 Feb 2022 21:35:40 +0000 (13:35 -0800)]
mptcp: fix race in overlapping signal events
After commit
a88c9e496937 ("mptcp: do not block subflows
creation on errors"), if a signal address races with a failing
subflow creation, the subflow creation failure control path
can trigger the selection of the next address to be announced
while the current announced is still pending.
The above will cause the unintended suppression of the ADD_ADDR
announce.
Fix the issue skipping the to-be-suppressed announce before it
will mark an endpoint as already used. The relevant announce
will be triggered again when the current one will complete.
Fixes:
a88c9e496937 ("mptcp: do not block subflows creation on errors")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 18 Feb 2022 21:35:39 +0000 (13:35 -0800)]
selftests: mptcp: improve 'fair usage on close' stability
The mentioned test has to wait for a subflow creation failure.
The current code looks for TCP sockets in TW state and sometimes
misses the relevant event. Switch to a more stable check, looking
for the associated mib counter.
Fixes:
46e967d187ed ("selftests: mptcp: add tests for subflow creation failure")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/257
Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 18 Feb 2022 21:35:38 +0000 (13:35 -0800)]
selftests: mptcp: fix diag instability
Instead of waiting for an arbitrary amount of time for the MPTCP
MP_CAPABLE handshake to complete, explicitly wait for the relevant
socket to enter into the established status.
Additionally let the data transfer application use the slowest
transfer mode available (-r), to cope with very slow host, or
high jitter caused by hosting VMs.
Fixes:
df62f2ec3df6 ("selftests/mptcp: add diag interface tests")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/258
Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Fri, 18 Feb 2022 13:15:35 +0000 (14:15 +0100)]
nfp: flower: Fix a potential leak in nfp_tunnel_add_shared_mac()
ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.
In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.
So set it to -1.
Fixes:
20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subash Abhinov Kasiviswanathan [Fri, 18 Feb 2022 08:50:18 +0000 (01:50 -0700)]
MAINTAINERS: rmnet: Update email addresses
Switch to the quicinc.com ids.
Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com>
Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Link: https://lore.kernel.org/r/1645174218-32632-1-git-send-email-quic_subashab@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jeremy Linton [Mon, 14 Feb 2022 23:18:52 +0000 (17:18 -0600)]
net: mvpp2: always set port pcs ops
Booting a MACCHIATObin with 5.17, the system OOPs with
a null pointer deref when the network is started. This
is caused by the pcs->ops structure being null in
mcpp2_acpi_start() when it tries to call pcs_config().
Hoisting the code which sets pcs_gmac.ops and pcs_xlg.ops,
assuring they are always set, fixes the problem.
The OOPs looks like:
[ 18.687760] Unable to handle kernel access to user memory outside uaccess routines at virtual address
0000000000000010
[ 18.698561] Mem abort info:
[ 18.698564] ESR = 0x96000004
[ 18.698567] EC = 0x25: DABT (current EL), IL = 32 bits
[ 18.709821] SET = 0, FnV = 0
[ 18.714292] EA = 0, S1PTW = 0
[ 18.718833] FSC = 0x04: level 0 translation fault
[ 18.725126] Data abort info:
[ 18.729408] ISV = 0, ISS = 0x00000004
[ 18.734655] CM = 0, WnR = 0
[ 18.738933] user pgtable: 4k pages, 48-bit VAs, pgdp=
0000000111bbf000
[ 18.745409] [
0000000000000010] pgd=
0000000000000000, p4d=
0000000000000000
[ 18.752235] Internal error: Oops:
96000004 [#1] SMP
[ 18.757134] Modules linked in: rfkill ip_set nf_tables nfnetlink qrtr sunrpc vfat fat omap_rng fuse zram xfs crct10dif_ce mvpp2 ghash_ce sbsa_gwdt phylink xhci_plat_hcd ahci_plam
[ 18.773481] CPU: 0 PID: 681 Comm: NetworkManager Not tainted 5.17.0-0.rc3.89.fc36.aarch64 #1
[ 18.781954] Hardware name: Marvell Armada 7k/8k Family Board /Armada 7k/8k Family Board , BIOS EDK II Jun 4 2019
[ 18.795222] pstate:
60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 18.802213] pc : mvpp2_start_dev+0x2b0/0x300 [mvpp2]
[ 18.807208] lr : mvpp2_start_dev+0x298/0x300 [mvpp2]
[ 18.812197] sp :
ffff80000b4732c0
[ 18.815522] x29:
ffff80000b4732c0 x28:
0000000000000000 x27:
ffffccab38ae57f8
[ 18.822689] x26:
ffff6eeb03065a10 x25:
ffff80000b473a30 x24:
ffff80000b4735b8
[ 18.829855] x23:
0000000000000000 x22:
00000000000001e0 x21:
ffff6eeb07b6ab68
[ 18.837021] x20:
ffff6eeb07b6ab30 x19:
ffff6eeb07b6a9c0 x18:
0000000000000014
[ 18.844187] x17:
00000000f6232bfe x16:
ffffccab899b1dc0 x15:
000000006a30f9fa
[ 18.851353] x14:
000000003b77bd50 x13:
000006dc896f0e8e x12:
001bbbfccfd0d3a2
[ 18.858519] x11:
0000000000001528 x10:
0000000000001548 x9 :
ffffccab38ad0fb0
[ 18.865685] x8 :
ffff80000b473330 x7 :
0000000000000000 x6 :
0000000000000000
[ 18.872851] x5 :
0000000000000000 x4 :
0000000000000000 x3 :
ffff80000b4732f8
[ 18.880017] x2 :
000000000000001a x1 :
0000000000000002 x0 :
ffff6eeb07b6ab68
[ 18.887183] Call trace:
[ 18.889637] mvpp2_start_dev+0x2b0/0x300 [mvpp2]
[ 18.894279] mvpp2_open+0x134/0x2b4 [mvpp2]
[ 18.898483] __dev_open+0x128/0x1e4
[ 18.901988] __dev_change_flags+0x17c/0x1d0
[ 18.906187] dev_change_flags+0x30/0x70
[ 18.910038] do_setlink+0x278/0xa7c
[ 18.913540] __rtnl_newlink+0x44c/0x7d0
[ 18.917391] rtnl_newlink+0x5c/0x8c
[ 18.920892] rtnetlink_rcv_msg+0x254/0x314
[ 18.925006] netlink_rcv_skb+0x48/0x10c
[ 18.928858] rtnetlink_rcv+0x24/0x30
[ 18.932449] netlink_unicast+0x290/0x2f4
[ 18.936386] netlink_sendmsg+0x1d0/0x41c
[ 18.940323] sock_sendmsg+0x60/0x70
[ 18.943825] ____sys_sendmsg+0x248/0x260
[ 18.947762] ___sys_sendmsg+0x74/0xa0
[ 18.951438] __sys_sendmsg+0x64/0xcc
[ 18.955027] __arm64_sys_sendmsg+0x30/0x40
[ 18.959140] invoke_syscall+0x50/0x120
[ 18.962906] el0_svc_common.constprop.0+0x4c/0xf4
[ 18.967629] do_el0_svc+0x30/0x9c
[ 18.970958] el0_svc+0x28/0xb0
[ 18.974025] el0t_64_sync_handler+0x10c/0x140
[ 18.978400] el0t_64_sync+0x1a4/0x1a8
[ 18.982078] Code:
52800004 b9416262 aa1503e0 52800041 (
f94008a5)
[ 18.988196] ---[ end trace
0000000000000000 ]---
Fixes:
cff056322372 ("net: mvpp2: use .mac_select_pcs() interface")
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20220214231852.3331430-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tom Rix [Mon, 14 Feb 2022 15:40:43 +0000 (07:40 -0800)]
ice: initialize local variable 'tlv'
Clang static analysis reports this issues
ice_common.c:5008:21: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ldo->phy_type_low |= ((u64)buf << (i * 16));
~~~~~~~~~~~~~~~~~ ^
When called from ice_cfg_phy_fec() ldo is the uninitialized local
variable tlv. So initialize.
Fixes:
ea78ce4dab05 ("ice: add link lenient and default override support")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tom Rix [Mon, 14 Feb 2022 14:33:27 +0000 (06:33 -0800)]
ice: check the return of ice_ptp_gettimex64
Clang static analysis reports this issue
time64.h:69:50: warning: The left operand of '+'
is a garbage value
set_normalized_timespec64(&ts_delta, lhs.tv_sec + rhs.tv_sec,
~~~~~~~~~~ ^
In ice_ptp_adjtime_nonatomic(), the timespec64 variable 'now'
is set by ice_ptp_gettimex64(). This function can fail
with -EBUSY, so 'now' can have a gargbage value.
So check the return.
Fixes:
06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jacob Keller [Mon, 7 Feb 2022 18:23:29 +0000 (10:23 -0800)]
ice: fix concurrent reset and removal of VFs
Commit
c503e63200c6 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200c6 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes:
c503e63200c6 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Michal Swiatkowski [Mon, 3 Jan 2022 06:41:21 +0000 (07:41 +0100)]
ice: fix setting l4 port flag when adding filter
Accidentally filter flag for none encapsulated l4 port field is always
set. Even if user wants to add encapsulated l4 port field.
Remove this unnecessary flag setting.
Fixes:
9e300987d4a81 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Wojciech Drewek [Fri, 17 Dec 2021 11:36:25 +0000 (12:36 +0100)]
ice: Match on all profiles in slow-path
In switchdev mode, slow-path rules need to match all protocols, in order
to correctly redirect unfiltered or missed packets to the uplink. To set
this up for the virtual function to uplink flow, the rule that redirects
packets to the control VSI must have the tunnel type set to
ICE_SW_TUN_AND_NON_TUN. As a result of that new tunnel type being set,
ice_get_compat_fv_bitmap will select ICE_PROF_ALL. At that point all
profiles would be selected for this rule, resulting in the desired
behavior. Without this change slow-path would not work with
tunnel protocols.
Fixes:
8b032a55c1bd ("ice: low level support for tunnels")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Xiaoke Wang [Fri, 18 Feb 2022 02:19:39 +0000 (10:19 +0800)]
net: ll_temac: check the return value of devm_kmalloc()
devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.
Fixes:
f14f5c11f051 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 17 Feb 2022 17:05:02 +0000 (09:05 -0800)]
net-timestamp: convert sk->sk_tskey to atomic_t
UDP sendmsg() can be lockless, this is causing all kinds
of data races.
This patch converts sk->sk_tskey to remove one of these races.
BUG: KCSAN: data-race in __ip_append_data / __ip_append_data
read to 0xffff8881035d4b6c of 4 bytes by task 8877 on cpu 1:
__ip_append_data+0x1c1/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff8881035d4b6c of 4 bytes by task 8880 on cpu 0:
__ip_append_data+0x1d8/0x1de0 net/ipv4/ip_output.c:994
ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000054d -> 0x0000054e
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8880 Comm: syz-executor.5 Not tainted
5.17.0-rc2-syzkaller-00167-gdcb85f85fa6f-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes:
09c2d251b707 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Thu, 17 Feb 2022 13:10:44 +0000 (14:10 +0100)]
sr9700: sanity check for packet length
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Thu, 17 Feb 2022 09:30:48 +0000 (11:30 +0200)]
net/sched: act_ct: Fix flow table lookup after ct clear or switching zones
Flow table lookup is skipped if packet either went through ct clear
action (which set the IP_CT_UNTRACKED flag on the packet), or while
switching zones and there is already a connection associated with
the packet. This will result in no SW offload of the connection,
and the and connection not being removed from flow table with
TCP teardown (fin/rst packet).
To fix the above, remove these unneccary checks in flow
table lookup.
Fixes:
46475bb20f4b ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
suresh kumar [Thu, 17 Feb 2022 01:55:18 +0000 (07:25 +0530)]
net-sysfs: add check for netdevice being present to speed_show
When bringing down the netdevice or system shutdown, a panic can be
triggered while accessing the sysfs path because the device is already
removed.
[ 755.549084] mlx5_core 0000:12:00.1: Shutdown was called
[ 756.404455] mlx5_core 0000:12:00.0: Shutdown was called
...
[ 757.937260] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 758.031397] IP: [<
ffffffff8ee11acb>] dma_pool_alloc+0x1ab/0x280
crash> bt
...
PID: 12649 TASK:
ffff8924108f2100 CPU: 1 COMMAND: "amsd"
...
#9 [
ffff89240e1a38b0] page_fault at
ffffffff8f38c778
[exception RIP: dma_pool_alloc+0x1ab]
RIP:
ffffffff8ee11acb RSP:
ffff89240e1a3968 RFLAGS:
00010046
RAX:
0000000000000246 RBX:
ffff89243d874100 RCX:
0000000000001000
RDX:
0000000000000000 RSI:
0000000000000246 RDI:
ffff89243d874090
RBP:
ffff89240e1a39c0 R8:
000000000001f080 R9:
ffff8905ffc03c00
R10:
ffffffffc04680d4 R11:
ffffffff8edde9fd R12:
00000000000080d0
R13:
ffff89243d874090 R14:
ffff89243d874080 R15:
0000000000000000
ORIG_RAX:
ffffffffffffffff CS: 0010 SS: 0018
#10 [
ffff89240e1a39c8] mlx5_alloc_cmd_msg at
ffffffffc04680f3 [mlx5_core]
#11 [
ffff89240e1a3a18] cmd_exec at
ffffffffc046ad62 [mlx5_core]
#12 [
ffff89240e1a3ab8] mlx5_cmd_exec at
ffffffffc046b4fb [mlx5_core]
#13 [
ffff89240e1a3ae8] mlx5_core_access_reg at
ffffffffc0475434 [mlx5_core]
#14 [
ffff89240e1a3b40] mlx5e_get_fec_caps at
ffffffffc04a7348 [mlx5_core]
#15 [
ffff89240e1a3bb0] get_fec_supported_advertised at
ffffffffc04992bf [mlx5_core]
#16 [
ffff89240e1a3c08] mlx5e_get_link_ksettings at
ffffffffc049ab36 [mlx5_core]
#17 [
ffff89240e1a3ce8] __ethtool_get_link_ksettings at
ffffffff8f25db46
#18 [
ffff89240e1a3d48] speed_show at
ffffffff8f277208
#19 [
ffff89240e1a3dd8] dev_attr_show at
ffffffff8f0b70e3
#20 [
ffff89240e1a3df8] sysfs_kf_seq_show at
ffffffff8eedbedf
#21 [
ffff89240e1a3e18] kernfs_seq_show at
ffffffff8eeda596
#22 [
ffff89240e1a3e28] seq_read at
ffffffff8ee76d10
#23 [
ffff89240e1a3e98] kernfs_fop_read at
ffffffff8eedaef5
#24 [
ffff89240e1a3ed8] vfs_read at
ffffffff8ee4e3ff
#25 [
ffff89240e1a3f08] sys_read at
ffffffff8ee4f27f
#26 [
ffff89240e1a3f50] system_call_fastpath at
ffffffff8f395f92
crash> net_device.state
ffff89443b0c0000
state = 0x5 (__LINK_STATE_START| __LINK_STATE_NOCARRIER)
To prevent this scenario, we also make sure that the netdevice is present.
Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duoming Zhou [Thu, 17 Feb 2022 01:43:03 +0000 (09:43 +0800)]
drivers: hamradio: 6pack: fix UAF bug caused by mod_timer()
When a 6pack device is detaching, the sixpack_close() will act to cleanup
necessary resources. Although del_timer_sync() in sixpack_close()
won't return if there is an active timer, one could use mod_timer() in
sp_xmit_on_air() to wake up timer again by calling userspace syscall such
as ax25_sendmsg(), ax25_connect() and ax25_ioctl().
This unexpected waked handler, sp_xmit_on_air(), realizes nothing about
the undergoing cleanup and may still call pty_write() to use driver layer
resources that have already been released.
One of the possible race conditions is shown below:
(USE) | (FREE)
ax25_sendmsg() |
ax25_queue_xmit() |
... |
sp_xmit() |
sp_encaps() | sixpack_close()
sp_xmit_on_air() | del_timer_sync(&sp->tx_t)
mod_timer(&sp->tx_t,...) | ...
| unregister_netdev()
| ...
(wait a while) | tty_release()
| tty_release_struct()
| release_tty()
sp_xmit_on_air() | tty_kref_put(tty_struct) //FREE
pty_write(tty_struct) //USE | ...
The corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in __run_timers.part.0+0x170/0x470
Write of size 8 at addr
ffff88800a652ab8 by task swapper/2/0
...
Call Trace:
...
queue_work_on+0x3f/0x50
pty_write+0xcd/0xe0pty_write+0xcd/0xe0
sp_xmit_on_air+0xb2/0x1f0
call_timer_fn+0x28/0x150
__run_timers.part.0+0x3c2/0x470
run_timer_softirq+0x3b/0x80
__do_softirq+0xf1/0x380
...
This patch reorders the del_timer_sync() after the unregister_netdev()
to avoid UAF bugs. Because the unregister_netdev() is well synchronized,
it flushs out any pending queues, waits the refcount of net_device
decreases to zero and removes net_device from kernel. There is not any
running routines after executing unregister_netdev(). Therefore, we could
not arouse timer from userspace again.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 17 Feb 2022 20:01:54 +0000 (12:01 -0800)]
Merge https://git./linux/kernel/git/bpf/bpf
Alexei Starovoitov says:
====================
pull-request: bpf 2022-02-17
We've added 8 non-merge commits during the last 7 day(s) which contain
a total of 8 files changed, 119 insertions(+), 15 deletions(-).
The main changes are:
1) Add schedule points in map batch ops, from Eric.
2) Fix bpf_msg_push_data with len 0, from Felix.
3) Fix crash due to incorrect copy_map_value, from Kumar.
4) Fix crash due to out of bounds access into reg2btf_ids, from Kumar.
5) Fix a bpf_timer initialization issue with clang, from Yonghong.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add schedule points in batch ops
bpf: Fix crash due to out of bounds access into reg2btf_ids.
selftests: bpf: Check bpf_msg_push_data return value
bpf: Fix a bpf_timer initialization issue
bpf: Emit bpf_timer in vmlinux BTF
selftests/bpf: Add test for bpf_timer overwriting crash
bpf: Fix crash due to incorrect copy_map_value
bpf: Do not try bpf_msg_push_data with len 0
====================
Link: https://lore.kernel.org/r/20220217190000.37925-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 17 Feb 2022 19:33:59 +0000 (11:33 -0800)]
Merge tag 'net-5.17-rc5' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices, avoid FW
assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling"
* tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
bonding: force carrier update when releasing slave
nfp: flower: netdev offload check for ip6gretap
ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
ipv4: fix data races in fib_alias_hw_flags_set
net: dsa: lan9303: add VLAN IDs to master device
net: dsa: lan9303: handle hwaccel VLAN tags
vsock: remove vsock from connected table when connect is interrupted by a signal
Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
ping: fix the dif and sdif check in ping_lookup
net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
net: sched: limit TC_ACT_REPEAT loops
tipc: fix wrong notification node addresses
net: dsa: lantiq_gswip: fix use after free in gswip_remove()
ipv6: per-netns exclusive flowlabel checks
net: bridge: multicast: notify switchdev driver whenever MC processing gets disabled
CDC-NCM: avoid overflow in sanity checking
mctp: fix use after free
net: mscc: ocelot: fix use-after-free in ocelot_vlan_del()
bonding: fix data-races around agg_select_timer
dpaa2-eth: Initialize mutex used in one step timestamping path
...
Zhang Changzhong [Wed, 16 Feb 2022 14:18:08 +0000 (22:18 +0800)]
bonding: force carrier update when releasing slave
In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.
Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.
Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0
Fixes:
ff59c4563a8d ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Thu, 17 Feb 2022 18:19:02 +0000 (10:19 -0800)]
bpf: Add schedule points in batch ops
syzbot reported various soft lockups caused by bpf batch operations.
INFO: task kworker/1:1:27 blocked for more than 140 seconds.
INFO: task hung in rcu_barrier
Nothing prevents batch ops to process huge amount of data,
we need to add schedule points in them.
Note that maybe_wait_bpf_programs(map) calls from
generic_map_delete_batch() can be factorized by moving
the call after the loop.
This will be done later in -next tree once we get this fix merged,
unless there is strong opinion doing this optimization sooner.
Fixes:
aa2e93b8e58e ("bpf: Add generic support for update and delete batch ops")
Fixes:
cb4d03ab499d ("bpf: Add generic support for lookup batch op")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/bpf/20220217181902.808742-1-eric.dumazet@gmail.com
Luis Chamberlain [Tue, 15 Feb 2022 02:08:28 +0000 (18:08 -0800)]
fs/file_table: fix adding missing kmemleak_not_leak()
Commit
b42bc9a3c511 ("Fix regression due to "fs: move binfmt_misc sysctl
to its own file") fixed a regression, however it failed to add a
kmemleak_not_leak().
Fixes:
b42bc9a3c511 ("Fix regression due to "fs: move binfmt_misc sysctl to its own file")
Reported-by: Tong Zhang <ztong0001@gmail.com>
Cc: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 17 Feb 2022 18:06:09 +0000 (10:06 -0800)]
Merge tag 'perf-tools-fixes-for-v5.17-2022-02-17' of git://git./linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix corrupt inject files when only last branch option is enabled with
ARM CoreSight ETM
- Fix use-after-free for realloc(..., 0) in libsubcmd, found by gcc 12
- Defer freeing string after possible strlen() on it in the BPF loader,
found by gcc 12
- Avoid early exit in 'perf trace' due SIGCHLD from non-workload
processes
- Fix arm64 perf_event_attr 'perf test's wrt --call-graph
initialization
- Fix libperf 32-bit build for 'perf test' wrt uint64_t printf
- Fix perf_cpu_map__for_each_cpu macro in libperf, providing access to
the CPU iterator
- Sync linux/perf_event.h UAPI with the kernel sources
- Update Jiri Olsa's email address in MAINTAINERS
* tag 'perf-tools-fixes-for-v5.17-2022-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf bpf: Defer freeing string after possible strlen() on it
perf test: Fix arm64 perf_event_attr tests wrt --call-graph initialization
libsubcmd: Fix use-after-free for realloc(..., 0)
libperf: Fix perf_cpu_map__for_each_cpu macro
perf cs-etm: Fix corrupt inject files when only last branch option is enabled
perf cs-etm: No-op refactor of synth opt usage
libperf: Fix 32-bit build for tests uint64_t printf
tools headers UAPI: Sync linux/perf_event.h with the kernel sources
perf trace: Avoid early exit due SIGCHLD from non-workload processes
MAINTAINERS: Update Jiri's email address
Linus Torvalds [Thu, 17 Feb 2022 17:54:00 +0000 (09:54 -0800)]
Merge tag 'modules-5.17-rc5' of git://git./linux/kernel/git/mcgrof/linux
Pull module fix from Luis Chamberlain:
"Fixes module decompression when CONFIG_SYSFS=n
The only fix trickled down for v5.17-rc cycle so far is the fix for
module decompression when CONFIG_SYSFS=n. This was reported through
0-day"
* tag 'modules-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module: fix building with sysfs disabled
Danie du Toit [Thu, 17 Feb 2022 12:48:20 +0000 (14:48 +0200)]
nfp: flower: netdev offload check for ip6gretap
IPv6 GRE tunnels are not being offloaded, this is caused by a missing
netdev offload check. The functionality of IPv6 GRE tunnel offloading
was previously added but this check was not included. Adding the
ip6gretap check allows IPv6 GRE tunnels to be offloaded correctly.
Fixes:
f7536ffb0986 ("nfp: flower: Allow ipv6gretap interface for offloading")
Signed-off-by: Danie du Toit <danie.dutoit@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220217124820.40436-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 16 Feb 2022 17:32:17 +0000 (09:32 -0800)]
ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
Because fib6_info_hw_flags_set() is called without any synchronization,
all accesses to gi6->offload, fi->trap and fi->offload_failed
need some basic protection like READ_ONCE()/WRITE_ONCE().
BUG: KCSAN: data-race in fib6_info_hw_flags_set / fib6_purge_rt
read to 0xffff8881087d5886 of 1 bytes by task 13953 on cpu 0:
fib6_drop_pcpu_from net/ipv6/ip6_fib.c:1007 [inline]
fib6_purge_rt+0x4f/0x580 net/ipv6/ip6_fib.c:1033
fib6_del_route net/ipv6/ip6_fib.c:1983 [inline]
fib6_del+0x696/0x890 net/ipv6/ip6_fib.c:2028
__ip6_del_rt net/ipv6/route.c:3876 [inline]
ip6_del_rt+0x83/0x140 net/ipv6/route.c:3891
__ipv6_dev_ac_dec+0x2b5/0x370 net/ipv6/anycast.c:374
ipv6_dev_ac_dec net/ipv6/anycast.c:387 [inline]
__ipv6_sock_ac_close+0x141/0x200 net/ipv6/anycast.c:207
ipv6_sock_ac_close+0x79/0x90 net/ipv6/anycast.c:220
inet6_release+0x32/0x50 net/ipv6/af_inet6.c:476
__sock_release net/socket.c:650 [inline]
sock_close+0x6c/0x150 net/socket.c:1318
__fput+0x295/0x520 fs/file_table.c:280
____fput+0x11/0x20 fs/file_table.c:313
task_work_run+0x8e/0x110 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x160/0x190 kernel/entry/common.c:207
__syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:300
do_syscall_64+0x50/0xd0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff8881087d5886 of 1 bytes by task 1912 on cpu 1:
fib6_info_hw_flags_set+0x155/0x3b0 net/ipv6/route.c:6230
nsim_fib6_rt_hw_flags_set drivers/net/netdevsim/fib.c:668 [inline]
nsim_fib6_rt_add drivers/net/netdevsim/fib.c:691 [inline]
nsim_fib6_rt_insert drivers/net/netdevsim/fib.c:756 [inline]
nsim_fib6_event drivers/net/netdevsim/fib.c:853 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:886 [inline]
nsim_fib_event_work+0x284f/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x2c7/0x2e0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30
value changed: 0x22 -> 0x2a
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1912 Comm: kworker/1:3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work
Fixes:
0c5fcf9e249e ("IPv6: Add "offload failed" indication to routes")
Fixes:
bb3c4ab93e44 ("ipv6: Add "offload" and "trap" indications to routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amit Cohen <amcohen@nvidia.com>
Cc: Ido Schimmel <idosch@nvidia.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220216173217.3792411-2-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 16 Feb 2022 17:32:16 +0000 (09:32 -0800)]
ipv4: fix data races in fib_alias_hw_flags_set
fib_alias_hw_flags_set() can be used by concurrent threads,
and is only RCU protected.
We need to annotate accesses to following fields of struct fib_alias:
offload, trap, offload_failed
Because of READ_ONCE()WRITE_ONCE() limitations, make these
field u8.
BUG: KCSAN: data-race in fib_alias_hw_flags_set / fib_alias_hw_flags_set
read to 0xffff888134224a6a of 1 bytes by task 2013 on cpu 1:
fib_alias_hw_flags_set+0x28a/0x470 net/ipv4/fib_trie.c:1050
nsim_fib4_rt_hw_flags_set drivers/net/netdevsim/fib.c:350 [inline]
nsim_fib4_rt_add drivers/net/netdevsim/fib.c:367 [inline]
nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:429 [inline]
nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
nsim_fib_event_work+0x1852/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
process_scheduled_works kernel/workqueue.c:2370 [inline]
worker_thread+0x7df/0xa70 kernel/workqueue.c:2456
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
write to 0xffff888134224a6a of 1 bytes by task 4872 on cpu 0:
fib_alias_hw_flags_set+0x2d5/0x470 net/ipv4/fib_trie.c:1054
nsim_fib4_rt_hw_flags_set drivers/net/netdevsim/fib.c:350 [inline]
nsim_fib4_rt_add drivers/net/netdevsim/fib.c:367 [inline]
nsim_fib4_rt_insert drivers/net/netdevsim/fib.c:429 [inline]
nsim_fib4_event drivers/net/netdevsim/fib.c:461 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:881 [inline]
nsim_fib_event_work+0x1852/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
process_scheduled_works kernel/workqueue.c:2370 [inline]
worker_thread+0x7df/0xa70 kernel/workqueue.c:2456
kthread+0x1bf/0x1e0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30
value changed: 0x00 -> 0x02
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 4872 Comm: kworker/0:0 Not tainted
5.17.0-rc3-syzkaller-00188-g1d41d2e82623-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work
Fixes:
90b93f1b31f8 ("ipv4: Add "offload" and "trap" indications to routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220216173217.3792411-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mans Rullgard [Wed, 16 Feb 2022 20:48:18 +0000 (20:48 +0000)]
net: dsa: lan9303: add VLAN IDs to master device
If the master device does VLAN filtering, the IDs used by the switch
must be added for any frames to be received. Do this in the
port_enable() function, and remove them in port_disable().
Fixes:
a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220216204818.28746-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mans Rullgard [Wed, 16 Feb 2022 12:46:34 +0000 (12:46 +0000)]
net: dsa: lan9303: handle hwaccel VLAN tags
Check for a hwaccel VLAN tag on rx and use it if present. Otherwise,
use __skb_vlan_pop() like the other tag parsers do. This fixes the case
where the VLAN tag has already been consumed by the master.
Fixes:
a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220216124634.23123-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>