--- /dev/null
+
+@set-syntax{C;\;}! tell GEMA to replace default Comment separator '!' by ';'
+;MSP430FRxxxx.pat
+
+; ============================================
+; FRAM INFO
+; ============================================
+; INFO_ORG=\$1800;
+
+; You can check the addresses below by comparing their values in DTCforthMSP430FRxxxx.lst
+; those addresses are usable with the symbolic assembler
+
+FREQ_KHZ=\$1800; FREQUENCY (in kHz)
+TERMBRW_RST=\$1802; TERMBRW_RST
+TERMMCTLW_RST=\$1804; TERMMCTLW_RST
+I2CSLAVEADR=\$1802; I2C_SLAVE address
+I2CSLAVEADR1=\$1804;
+LPM_MODE=\$1806; LPM_MODE value, LPM0+GIE is the default value
+USERSYS=\$1808; user SYS variable, defines software RESET, DEEP_RST, INIT_HARWARE, etc.
+VERSION=\$180A;
+THREADS=\$180C; THREADS
+; ---------------------------------------------
+KERNEL_ADDON=\$180E;
+; ---------------------------------------------
+FLOORED=\$8000; BIT15=FLOORED DIVISION
+LF_XTAL=\$4000; BIT14=LF_XTAL
+; BIT13=UART CTS
+; BIT12=UART RTS
+; BIT11=UART XON/XOFF
+; BIT10=UART half duplex
+; BIT9=I2C_TERMINAL
+; BIT8=Q15.16 input
+; BIT7=DOUBLE input
+; BIT6=assembler 20 bits
+; BIT5=assembler 16 bits
+; BIT4=assembler 16 bits with 20 bits addr
+HMPY=8; BIT3=hardware MPY
+; BIT2=
+; BIT1=
+; BIT0=
+; ----------------------------------------------
+DEEP_ORG=\$1810; MOV #DEEP_ORG,X
+; ----------------------------------------------
+DEEP_TERM_VEC=\$1810; address of default TERMINAL vector
+DEEP_STOP=\$1812; address of default STOP_APP
+DEEP_SOFT=\$1814; address of default SOFT_APP
+DEEP_HARD=\$1816; address of default HARD_APP
+DEEP_BACKGRND=\$1818; address of default BACKGRND_APP
+DEEP_DP=\$181A; to DEEP_INIT RST_DP
+DEEP_LASTVOC=\$181C; to DEEP_INIT RST_LASTVOC
+DEEP_CURRENT=\$181E; to DEEP_INIT RST_CURRENT
+DEEP_CONTEXT=\$1820; to DEEP_INIT RST_CONTEXT
+;
+; ----------------------------------------------
+PUC_ABORT_ORG=\$1822; MOV #PUC_ABORT_ORG,X
+; ----------------------------------------------
+INIT_ACCEPT=\$1822; to INIT PFA_ACCEPT
+INIT_EMIT=\$1824; to INIT PFA_EMIT
+INIT_KEY=\$1826; to INIT PFA_KEY
+INIT_CIB=\$1828; to INIT CIB_ORG
+;
+; ----------------------------------------------
+FORTH_ORG=\$182A; MOV #FORTH_ORG,X \to preserve the state of DEFERed words
+; ----------------------------------------------
+INIT_RSP=\$182A; to INIT RSP
+; ----------------------------------------------
+INIT_DOXXX=\$182C; MOV #INIT_DOXXX,X \ to restore DOxxx registers
+; ----------------------------------------------
+INIT_DOCOL=\$182C; to INIT rDOCOL (R4) to restore rDOCOL: MOV &INIT_DOCOL,rDOCOL
+INIT_DODOES=\$182E; to INIT rDODOES (R5)
+INIT_DOCON=\$1830; to INIT rDOCON (R6)
+INIT_DOVAR=\$1832; to INIT rDOVAR (R7)
+INIT_CAPS=\$1834; to INIT CAPS
+INIT_BASE=\$1836; to INIT BASE
+INIT_LEAVE=\$1838; to INIT LEAVEPTR
+;
+; ----------------------------------------------
+RST_ORG=\$183A;
+RST_LEN=\$10; 16 bytes
+; ----------------------------------------------
+STOP_APP=\$183A; address of current STOP_APP
+SOFT_APP=\$183C; address of current SOFT_APP
+HARD_APP=\$183E; address of current HARD_APP
+BACKGRND_APP=\$1840; address of current BACKGRND_APP
+RST_DP=\$1842; RST_RET value for (RAM) DDP
+RST_LASTVOC=\$1844; RST_RET value for (RAM) LASTVOC
+RST_CURRENT=\$1846; RST_RET value for (RAM) CURRENT
+RST_CONTEXT=\$1848; RST_RET value for (RAM) CONTEXT (8 CELLS)
+;
+; ===============================================
+; FAST FORTH V 4.0: FRAM usage, INFO space free from $185A to $19FF
+; ===============================================
+;
+; ============================================
+; FRAM TLV
+; ============================================
+TLV_ORG=\$1A00; Device Descriptor Info (Tag-Lenght-Value)
+TLV_LEN=\$0100;
+DEVICEID=\$1A04;
+
+; ============================================
+; FORTH RAM areas :
+; ============================================
+LSTACK_SIZE=\#16; words
+PSTACK_SIZE=\#48; words
+RSTACK_SIZE=\#48; words
+PAD_LEN=\#84; bytes
+CIB_LEN=\#84; bytes
+HOLD_SIZE=\#34; bytes
+
+; ============================================
+; FRAM MAIN
+; ============================================
+; to use in ASSEMBLER mode
+; see device.pat for other addresses
+
+I2C_CTRL=KEY\+\$0A; used as is: MOV.B #<CTRL_CHAR>,Y
+; CALL #I2C_CTRL
+\#UART_RXON=\#KEY\+8; CALL #UART_RXON
+\#UART_RXOFF=\#ACCEPT\+\$26; CALL #UART_RXOFF
+\#BACKGRND=\#ACCEPT\+\$1C; MOV #BACKGRND,PC
+\#STOP_APP=\&SYS\+2; CALL #STOP_APP
+\#TOS2WARM=\#SYS\+\$0E; CALL #TOS2WARM WARM with TOS value
+\#TOS2COLD=\#SYS\+\$14; CALL #TOS2COLD COLD with TOS value
+INTERPRET=\\+\$08; address used in CORE_ANS.f
+\#ABORT=\#ALLOT\+\$08; MOV #ABORT,PC used in CORE_ANS.f
+\#QUIT=\#ALLOT\+\$0E; MOV #QUIT,PC used in CORE_ANS.f
+\#D\.=\#U\.+\$0A; MOV #D.,PC used in DOUBLE.f
+\#Read_File=\&READ\+\$0C; CALL #Read_File, sequentially load a sector in SD_BUF
+\#Write_File=\#WRITE\+4; CALL #Write_File, sequentially write SD_BUF in a sector
OSDN Git Service
