-! -*- coding: utf-8 -*-
-! MSP_EXP430FR2355.pat
-!
-\.f=\.4th for MSP_EXP430FR2355! to change file type
-!
-!========================
-! remove comments
-!========================
-\\*\n=! entire comment lines
-\s\\*\n=\n! comments at end of line
-! ======================================================================
-! MSP430FR2355 Config
-! ======================================================================
-@define{@read{@mergepath{@inpath{};MSP430FR2355.pat;}}}
+
+@set-syntax{C;\;}! tell GEMA to replace default Comment separator '!' by ';'
+; ========================
+; MSP_EXP430FR2355.pat
+; ========================
+\.f=\.4th for MSP_EXP430FR2355; to change file type from generic to targeted
+
+; ========================
+; remove comments
+; ========================
+\\*\n=; remove entire commented lines
+\s\\*\n=\n; remove comments at end of line
+
+; ======================================================================
+; MSP430FR2355 Config
+; ======================================================================
+@reset-syntax{}; enable good interpreting of next line
@define{@read{@mergepath{@inpath{};FastForthREGtoTI.pat;}}}
+@reset-syntax{}; enable good interpreting of next line
+@define{@read{@mergepath{@inpath{};MSP430FRxxxx.pat;}}}
+@reset-syntax{}; enable good interpreting of next line
+@define{@read{@mergepath{@inpath{};MSP430FR2xxx.pat;}}}
+@reset-syntax{}; enable good interpreting of next line
+@define{@read{@mergepath{@inpath{};MSP430FR2355.pat;}}}
-! ======================================================================
-! INIT MSP-EXP430FR2355 board
-! ======================================================================
-!
-! J101 (7xjumper)
-! "SBWTCK" ---> TEST
-! "SBWTDIO" ---> RST
-! "TXD" <--- P4.3 == UCA0TXD <-- UCA0TXDBUf
-! "RXD" ---> P4.2 == UCA0RXD --> UCA0RXDBUF
-! "3V3" <--> 3V3
-! "5V0" <--> 5V0
-! "GND" <--> GND
-!
-!
-! SW1 -- P4.1
-! SW2 -- P2.3
-!
-! LED1 - P1.0 (red)
-! LED2 - P6.6 (green)
-!
-! I/O pins on J1:
-! J1.1 - 3V3
-! J1.2 - P1.5
-! J1.3 - P1.6
-! J1.4 - P1.7
-! J1.5 - P3.6
-! J1.6 - P5.2
-! J1.7 - P4.5
-! J1.8 - P3.4
-! J1.9 - P1.3
-! J1.10 - P1.2
-!
-! I/O pins on J3:
-! J3.21 - 5V0
-! J3.22 - GND
-! J3.23 - P1.4 A4 SEED
-! J3.24 - P5.3 A11
-! J3.25 - P5.1 A9
-! J3.26 - P5.0 A8
-! J3.27 - P5.4
-! J3.28 - P1.1 A1 SEED
-! J3.29 - P3.5 OA3O
-! J3.30 - P3.1 OA2O
-!
-!
-! I/O pins on J2:
-! J2.11 - P3.0
-! J2.12 - P2.5
-! J2.13 - P4.4
-! J2.14 - P4.7
-! J2.15 - P4.6
-! J2.16 - RST
-! J2.17 - P4.0
-! J2.18 - P2.2
-! J2.19 - P2.0
-! J2.20 - GND
-!
-! I/O pins on J4:
-! J2.31 - P3.2
-! J2.32 - P3.3
-! J2.33 - P2.4
-! J2.34 - P3.7
-! J2.35 - P6.4
-! J2.36 - P6.3
-! J2.37 - P6.2
-! J2.38 - P6.1
-! J2.39 - P6.0
-! J2.40 - 2.1
-!
-! LFXTAL XOUT- P2.6
-! LFXTAL XIN - P2.7
-
-
-!
-! ======================================================================
-! MSP_EXP430FR2355 LAUNCHPAD <--> OUTPUT WORLD
-! ======================================================================
-!
-! +--4k7-< DeepRST switch <-- GND
-! |
-! P4.3 - UCA1 TXD J101.6 - <-+-> RX UARTtoUSB bridge
-! P4.2 - UCA1 RXD J101.8 - <---- TX UARTtoUSB bridge
-! P2.0 - RTS J2.19 - ----> CTS UARTtoUSB bridge (TERMINAL4WIRES)
-! P2.1 - CTS J4.40 - <---- RTS UARTtoUSB bridge (TERMINAL5WIRES)
-!
-! P1.2 - UCB0 SDA J1.10 - <---> SDA I2C Master_Slave
-! P1.3 - UCB0 SCL J1.9 - ----> SCL I2C Master_Slave
-!
-! P2.2 - J2.18 - <---- TSSOP32236 (IR RC5)
-!
-! P2.5 - J2.12 - ----> SD_CS (Card Select)
-! P4.4 - J2.13 - <---- SD_CD (Card Detect)
-! P4.5 - UCB1 CLK J1.7 - ----> SD_CLK
-! P4.7 - UCB1 SOMI J2.14 - <---- SD_SDO
-! P4.6 - UCB1 SIMO J2.15 - ----> SD_SDI
-!
-! P3.2 - J4.38 - <---> SDA I2C Soft_Master
-! P3.3 - J4.39 - ----> SCL I2C Soft_Master
-
-! GND <-------+---0V0----------> 1 LCD_Vss
-! VCC <------ | --3V6-----+----> 2 LCD_Vdd
-! | |
-! |___ 470n ---
-! ^ | ---
-! / \ BAT54 |
-! --- |
-! 100n | 2k2 |
-! P1.7 >---||--+--^/\/\/v--+----> 3 LCD_Vo (=0V6 without modulation)
-! P1.5 >------------------------> 4 LCD_RS
-! P1.4 >------------------------> 5 LCD_R/W
-! P1.1 >------------------------> 6 LCD_EN
-
-! P6.0 <------------------------> 11 LCD_DB4
-! P6.1 <------------------------> 12 LCD_DB5
-! P6.2 <------------------------> 13 LCD_DB5
-! P6.3 <------------------------> 14 LCD_DB7
-
-! P4.1 ---> S2 LCD contrast +
-! P2.3 ---> S1 LCD contrast -
-
-
-! ============================================
-! FORTH TERMINAL I/O :
-! ============================================
-!TERMINAL
-BUS_TERM=\$0C! P4.2 = RX, P4.3 = TX
-
-TERM_IN=\$221! P4
-TERM_REN=\$227!
-TERM_SEL=\$22B! SEL0
-
-RTS=1! P2.0
-CTS=2! P2.1
-HANDSHAKIN=\$201!
-HANDSHAKOUT=\$203!
-
-XT1_OUT=\$203! P2
-XT1_DIR=\$205! P2
-XT1_SEL=\$20D! P2SEL1
-XIN=\$80!
-XOUT=\$40!
-
-! ============================================
-! FORTH TERMINAL hardware
-! ============================================
-TERM_CTLW0=\$580! \ eUSCI_A1 control word 0
-TERM_CTLW1=\$582! \ eUSCI_A1 control word 1
-TERM_BRW=\$586!
-TERM_BR0=\$586! \ eUSCI_A1 baud rate 0
-TERM_BR1=\$587! \ eUSCI_A1 baud rate 1
-TERM_MCTLW=\$588! \ eUSCI_A1 modulation control
-TERM_STATW=\$58A! \ eUSCI_A1 status
-TERM_RXBUF=\$58C! \ eUSCI_A1 receive buffer
-TERM_TXBUF=\$58E! \ eUSCI_A1 transmit buffer
-TERM_ABCTL=\$590! \ eUSCI_A1 LIN control
-TERM_IRTCTL=\$592! \ eUSCI_A1 IrDA transmit control
-TERM_IRRCTL=\$593! \ eUSCI_A1 IrDA receive control
-TERM_IE=\$59A! \ eUSCI_A1 interrupt enable
-TERM_IFG=\$59C! \ eUSCI_A1 interrupt flags
-TERM_IV=\$59E! \ eUSCI_A1 interrupt vector word
-
-WAKE_UP=1! UART RX interrupt
-RX_TERM=1! RX flag ifg
-TX_TERM=2! Tx flag ifg
-
-! ============================================
-! FRAM MAIN
-! ============================================
-TERM_VEC=\$FFE2! vector for eUSCI_A1
-
-! ============================================
-! APPLICATION I/O :
-! ============================================
-LED1_OUT=\$202!
-LED1_DIR=\$204!
-LED1=1! P1.0 LED1 red
-
-LED2_OUT=\$243!
-LED2_DIR=\$245!
-LED2=\$40! P6.6 LED2 green
-
-SW1_IN=\$221!
-SW1=2! P4.1 = S1
-
-WIPE_IN=\$221!
-WIPE=2! P4.1 = S1 = FORTH Deep_RST pin
-
-SW2_IN=\$201!
-SW2=8! P2.3
-
-
-!LCD_Vo PWM
-LCDVo_DIR=\$204! P1
-LCDVo_SEL=\$20C! SEL1
-LCDVo=\$80! P1.7 as TB0.2
-!LCD command bus
-LCD_CMD_IN=\$200! P1
+; ======================================================================
+; INIT MSP-EXP430FR2355 board
+; ======================================================================
+;
+; J101 (7xjumper)
+; "SBWTCK" ---> TEST
+; "SBWTDIO" ---> RST
+; "TXD" <--- P4.3 == UCA0TXD <-- UCA0TXDBUf
+; "RXD" ---> P4.2 == UCA0RXD --> UCA0RXDBUF
+; "3V3" <--> 3V3
+; "5V0" <--> 5V0
+; "GND" <--> GND
+;
+;
+; SW1 -- P4.1
+; SW2 -- P2.3
+;
+; LED1 - P1.0 (red)
+; LED2 - P6.6 (green)
+;
+; I/O pins on J1:
+; J1.1 - 3V3
+; J1.2 - P1.5
+; J1.3 - P1.6
+; J1.4 - P1.7
+; J1.5 - P3.6
+; J1.6 - P5.2
+; J1.7 - P4.5
+; J1.8 - P3.4
+; J1.9 - P1.3
+; J1.10 - P1.2
+;
+; I/O pins on J3:
+; J3.21 - 5V0
+; J3.22 - GND
+; J3.23 - P1.4 A4 SEED
+; J3.24 - P5.3 A11
+; J3.25 - P5.1 A9
+; J3.26 - P5.0 A8
+; J3.27 - P5.4
+; J3.28 - P1.1 A1 SEED
+; J3.29 - P3.5 OA3O
+; J3.30 - P3.1 OA2O
+;
+;
+; I/O pins on J2:
+; J2.11 - P3.0
+; J2.12 - P2.5
+; J2.13 - P4.4
+; J2.14 - P4.7
+; J2.15 - P4.6
+; J2.16 - RST
+; J2.17 - P4.0
+; J2.18 - P2.2
+; J2.19 - P2.0
+; J2.20 - GND
+;
+; I/O pins on J4:
+; J2.31 - P3.2
+; J2.32 - P3.3
+; J2.33 - P2.4
+; J2.34 - P3.7
+; J2.35 - P6.4
+; J2.36 - P6.3
+; J2.37 - P6.2
+; J2.38 - P6.1
+; J2.39 - P6.0
+; J2.40 - 2.1
+;
+; LFXTAL XOUT- P2.6
+; LFXTAL XIN - P2.7
+
+
+;
+; ======================================================================
+; MSP_EXP430FR2355 LAUNCHPAD <--> OUTPUT WORLD
+; ======================================================================
+;
+; +--4k7-< DeepRST switch <-- GND
+; |
+; P4.3 - UCA1 TXD J101.6 - <-+-> RX UARTtoUSB bridge
+; P4.2 - UCA1 RXD J101.8 - <---- TX UARTtoUSB bridge
+; P2.0 - RTS J2.19 - ----> CTS UARTtoUSB bridge (TERMINAL4WIRES)
+; P2.1 - CTS J4.40 - <---- RTS UARTtoUSB bridge (TERMINAL5WIRES)
+;
+; P1.2 - UCB0 SDA J1.10 - <---> SDA I2C hardware Slave
+; P1.3 - UCB0 SCL J1.9 - ----> SCL I2C hardware Slave
+;
+; P2.2 - J2.18 - <---- TSSOP32236 (IR RC5)
+;
+; P2.5 - J2.12 - ----> SD_CS (Card Select)
+; P4.4 - J2.13 - <---- SD_CD (Card Detect)
+; P4.5 - UCB1 CLK J1.7 - ----> SD_CLK
+; P4.7 - UCB1 SOMI J2.14 - <---- SD_SDO
+; P4.6 - UCB1 SIMO J2.15 - ----> SD_SDI
+;
+; P3.2 - J4.38 - <---> SDA I2C Soft_Master
+; P3.3 - J4.39 - ----> SCL I2C Soft_Master
+
+; GND <-------+---0V0----------> 1 LCD_Vss
+; VCC <------ | --3V6-----+----> 2 LCD_Vdd
+; | |
+; |___ 470n ---
+; ^ | ---
+; / \ BAT54 |
+; --- |
+; 100n | 2k2 |
+; P1.7 >---||--+--^/\/\/v--+----> 3 LCD_Vo (=0V6 without modulation)
+; P1.5 >------------------------> 4 LCD_RS
+; P1.4 >------------------------> 5 LCD_R/W
+; P1.1 >------------------------> 6 LCD_EN
+
+; P6.0 <------------------------> 11 LCD_DB4
+; P6.1 <------------------------> 12 LCD_DB5
+; P6.2 <------------------------> 13 LCD_DB5
+; P6.3 <------------------------> 14 LCD_DB7
+
+; P4.1 ---> S2 LCD contrast +
+; P2.3 ---> S1 LCD contrast -
+
+
+; ----------------------------------------------------------------------
+; MSP430FR2355 Peripheral File Map
+; ----------------------------------------------------------------------
+;SFR_SFR .equ 0100h ; Special function
+;PMM_SFR .equ 0120h ; PMM
+;SYS_SFR .equ 0140h ; SYS
+;CS_SFR .equ 0180h ; Clock System
+;FRAM_SFR .equ 01A0h ; FRAM control
+;CRC16_SFR .equ 01C0h
+;WDT_A_SFR .equ 01CCh ; Watchdog
+;PA_SFR .equ 0200h ; PORT1/2
+;PB_SFR .equ 0220h ; PORT3/4
+;PC_SFR .equ 0240h ; PORT5/6
+;RTC_SFR .equ 0300h
+;TB0_SFR .equ 0380h
+;TB1_SFR .equ 03C0h
+;TB2_SFR .equ 0400h
+;TB3_SFR .equ 0440h
+;MPY_SFR .equ 04C0h
+;eUSCI_A0_SFR .equ 0500h ; eUSCI_A0
+;eUSCI_B0_SFR .equ 0540h ; eUSCI_B0
+;eUSCI_A1_SFR .equ 0580h ; eUSCI_A1
+;eUSCI_B1_SFR .equ 05C0h ; eUSCI_B1
+;BACK_MEM_SFR .equ 0660h
+;ICC_SFR .equ 06C0h
+;ADC10_B_SFR .equ 0700h
+;eCOMP0_SFR .equ 08E0h
+;eCOMP1_SFR .equ 0900h
+;SAC0_SFR .equ 0C80h
+;SAC1_SFR .equ 0C90h
+;SAC2_SFR .equ 0CA0h
+;SAC3_SFR .equ 0CB0h
+
+;P4_VEC=\$FFCE;
+;P3_VEC=\$FFD0;
+;P2_VEC=\$FFD2;
+;P1_VEC=\$FFD4;
+;SAC1SAC3_VEC=\$FFD6;
+;SAC0SAC2_VEC=\$FFD8;
+;ECOMPX_VEC=\$FFDA;
+;ADC12_VEC=\$FFDC;
+;EUSCI_B1_VEC=\$FFDE;
+;EUSCI_B0_VEC=\$FFE0;
+;EUSCI_A1_VEC=\$FFE2;
+;EUSCI_A0_VEC=\$FFE4;
+;WDT_VEC=\$FFE6;
+;RTC_VEC=\$FFE8;
+;TB3_X_VEC=\$FFEA;
+;TB3_0_VEC=\$FFEC;
+;TB2_X_VEC=\$FFEE;
+;TB2_0_VEC=\$FFF0;
+;TB1_X_VEC=\$FFF2;
+;TB1_0_VEC=\$FFF4;
+;TB0_X_VEC=\$FFF6;
+;TB0_0_VEC=\$FFF8;
+;U_NMI_VEC=\$FFFA;
+;S_NMI_VEC=\$FFFC;
+;RST_VEC=\$FFFE;
+
+; ============================================
+; FAST FORTH configuration :
+; ============================================
+;TERMINAL P4.2 = RX, P4.3 = TX
+BUS_TERM=\$0C
+TERM_IN=\$221; P4
+TERM_REN=\$227
+TERM_SEL=\$22B; SEL0
+
+TERM_VEC=\$FFE2; vector for eUSCI_A1
+UCSWRST=1; eUSCI Software Reset
+WAKE_UP=1; UART RX interrupt
+RX=1; RX flag IE|IFG
+TX=2; Tx flag IE|IFG
+
+RTS=1; P2.0
+CTS=2; P2.1
+HANDSHAKIN=\$201
+HANDSHAKOUT=\$203
+
+TERM_CTLW0=\$580; eUSCI_A1 control word 0
+TERM_CTLW1=\$582; eUSCI_A1 control word 1
+TERM_BRW=\$586; eUSCI_A1 baud rate
+TERM_MCTLW=\$588; eUSCI_A1 modulation control
+TERM_STATW=\$58A; eUSCI_A1 status
+TERM_RXBUF=\$58C; eUSCI_A1 receive buffer
+TERM_TXBUF=\$58E; eUSCI_A1 transmit buffer
+TERM_IE=\$59A; eUSCI_A1 interrupt enable
+TERM_IFG=\$59C; eUSCI_A1 interrupt flags
+TERM_IV=\$59E; eUSCI_A1 interrupt vector word
+
+LFXT_OUT=\$203; P2
+LFXT_DIR=\$205; P2
+LFXT_SEL=\$20D; P2SEL1
+LFXIN=\$80; P2.7
+LFXOUT=\$40; P2.6
+
+; FAST FORTH I/O :
+LED1_OUT=\$202
+LED1_DIR=\$204
+LED1=1; P1.0 LED1 red
+LED2_OUT=\$243
+LED2_DIR=\$245
+LED2=\$40; P6.6 LED2 green
+
+SW1_IN=\$221
+SW1=2; P4.1 = S1
+SW2_IN=\$201
+SW2=8; P2.3 = S2
+
+; ============================================
+; COMMON UARTI2CS & RC5toLCD APPLICATIONs
+; ============================================
+;Software I2C_Master
+I2CSM_IN=\$220
+I2CSM_OUT=\$222
+I2CSM_DIR=\$224
+I2CSM_REN=\$226
+I2CSM_IES=\$238
+I2CSM_IFG=\$23C
+SM_SDA=4; P3.2
+SM_SCL=8; P3.3
+SM_BUS=\$0C
+
+; ============================================
+; UARTI2CS APPLICATION
+; ============================================
+;500_ms_INT TIMER = TB0
+TIM_CTL=\$380
+TIM_CCTL2=\$386
+TIM_CCR0=\$392
+TIM_CCR2=\$396
+T_OUT2=\$80; P1.7 <--- TB0.2
+T_OUT2_DIR=\$204; P1DIR
+T_OUT2_SEL=\$20C; P1SEL1
+INT_IN=\$40; P1.6
+INT_IN_IE=\$21A; P1IE
+INT_IN_IFG=\$21C; P1IFG
+INT_IN_VEC=\$FFD4; P1VEC
+
+;local variables
+UARTI2CS_ADR=\{UARTI2CS\}\+10; <-- I2C_Slave_Addr<<1
+TIMER_CONF=\{UARTI2CS\}\+12; <-- TIM_CTL configuration
+COLLISION_DLY=\{UARTI2CS\}\+14; <-- 20 us resolution delay after I2C collision
+DUPLEX_MODE=\{UARTI2CS\}\+15; <-- flag = 4 --> NOECHO, <> 4 --> ECHO, -1 = I2C link lost
+; ============================================
+; RC5toLCD APPLICATION
+; ============================================
+;LCD_Vo PWM P1
+LCDVo_DIR=\$204
+LCDVo_SEL=\$20C; SEL1
+LCDVo=\$80; P1.7 as TB0.2
+
+;LCD command bus P1
+LCD_CMD_IN=\$200
LCD_CMD_OUT=\$202
LCD_CMD_DIR=\$204
LCD_CMD_REN=\$206
-LCD_RS=\$20! P1.5
-LCD_RW=\$10! P1.4
-LCD_EN=2! P1.1
-LCD_CMD=\$32!
-!LCD data bus
-LCD_DB_IN=\$341! P6
+LCD_RS=\$20; P1.5
+LCD_RW=\$10; P1.4
+LCD_EN=2; P1.1
+LCD_CMD=\$32;
+;LCD data bus P6
+LCD_DB_IN=\$341
LCD_DB_OUT=\$343
LCD_DB_DIR=\$345
LCD_DB_REN=\$347
-LCD_DB=\$0F! P6.3210
-!LCD timer
-LCD_TIM_CTL=\$380! TB0CTL
-LCD_TIM_CCTLn=\$386! TB0CCTL2
-LCD_TIM_CCR0=\$392! TB0CCR0
-LCD_TIM_CCRn=\$396! TB0CCR2
-LCD_TIM_EX0=\$3A0! TB0EX0
-
-
-!WATCHDOG timer
-WDT_TIM_CTL=\$3C2! TB1CTL
-WDT_TIM_CCTL0=\$3C2! TB1CCTL0
-WDT_TIM_CCR0=\$3D2! TB1CCR0
-WDT_TIM_EX0=\$3E0! TB1EX0
-WDT_TIM_0_VEC=\$FFF4! TB1_0_VEC
-
-
-!IR_RC5
-RC5_=RC5_!
-IR_IN=\$201!
-IR_OUT=\$203!
-IR_DIR=\$205!
-IR_REN=\$209!
-IR_IES=\$219!
-IR_IE=\$21B!
-IR_IFG=\$21D!
-IR_VEC=\$FFD2! P2 int
-RC5=4! P2.2
-!IR_RC5 timer
-RC5_TIM_CTL=\$400! TB2CTL
-RC5_TIM_R=\$410! TB2R
-RC5_TIM_EX0=\$420! TB2EX0
-
-!Software I2C_Master
-I2CSM_IN=\$220!
-I2CSM_OUT=\$222!
-I2CSM_DIR=\$224!
-I2CSM_REN=\$226!
-I2CSM_IES=\$238!
-I2CSM_IFG=\$23C!
-SM_SDA=4! P3.2
-SM_SCL=8! P3.3
-SM_BUS=\$0C!
-
-!Software I2C_Multi_Master
-I2CSMM_IN=\$220!
-I2CSMM_OUT=\$222!
-I2CSMM_DIR=\$224!
-I2CSMM_REN=\$226!
-I2CSMM_IES=\$238!
-I2CSMM_IFG=\$23C!
-SMM_SDA=4! P3.2
-SMM_SCL=8! P3.3
-SMM_BUS=\$0C!
-
-!hardware I2C_Multi_Master
-I2CMM_IN=\$200!
-I2CMM_OUT=\$202!
-I2CMM_DIR=\$204!
-I2CMM_REN=\$206!
-I2CMM_SEL=\$20A! SEL0
-I2CMM_VEC=\$FFE0! UCB0
-MM_SDA=4! P1.2
-MM_SCL=8! P1.3
-MM_BUS=\$0C!
-
-!hardware I2C_Master
-I2CM_IN=\$200!
-I2CM_OUT=\$202!
-I2CM_DIR=\$204!
-I2CM_REN=\$206!
-I2CM_SEL=\$20A! SEL0
-I2CM_VEC=\$FFE0! UCB0
-M_SDA=4! P1.2
-M_SCL=8! P1.3
-M_BUS=\$0C!
-
-!hardware I2C_Slave
-I2CS_IN=\$200!
-I2CS_OUT=\$202!
-I2CS_DIR=\$204!
-I2CS_REN=\$206!
-I2CS_SEL=\$20A! SEL0
-I2CS_VEC=\$FFE0! UCB0
-S_SDA=4! P1.2
-S_SCL=8! P1.3
-S_BUS=\$0C!
-I2CMM_VEC=\$FFE0! UCB0
-
-UCSWRST=1! eUSCI Software Reset
-UCTXIE=2! eUSCI Transmit Interrupt Enable
-UCRXIE=1! eUSCI Receive Interrupt Enable
-UCTXIFG=2! eUSCI Transmit Interrupt Flag
-UCRXIFG=1! eUSCI Receive Interrupt Flag
-UCTXIE0=2! eUSCI_B Transmit Interrupt Enable
-UCRXIE0=1! eUSCI_B Receive Interrupt Enable
-UCTXIFG0=2! eUSCI_B Transmit Interrupt Flag
-UCRXIFG0=1! eUSCI_B Receive Interrupt Flag
-
-I2CM_CTLW0=\$540! USCI_B0 Control Word Register 0
-I2CM_CTLW1=\$542! USCI_B0 Control Word Register 1
-I2CM_BRW=\$546! USCI_B0 Baud Word Rate 0
-I2CM_STATW=\$548! USCI_B0 status word
-I2CM_TBCNT=\$54A! USCI_B0 byte counter threshold
-I2CM_RXBUF=\$54C! USCI_B0 Receive Buffer 8
-I2CM_TXBUF=\$54E! USCI_B0 Transmit Buffer 8
-I2CM_I2COA0=\$554! USCI_B0 I2C Own Address 0
-I2CM_ADDRX=\$55C! USCI_B0 Received Address Register
-I2CM_I2CSA=\$560! USCI_B0 I2C Slave Address
-I2CM_IE=\$56A! USCI_B0 Interrupt Enable
-I2CM_IFG=\$56C! USCI_B0 Interrupt Flags Register
-
-I2CS_CTLW0=\$540! USCI_B0 Control Word Register 0
-I2CS_CTLW1=\$542! USCI_B0 Control Word Register 1
-I2CS_BRW=\$546! USCI_B0 Baud Word Rate 0
-I2CS_STATW=\$548! USCI_B0 status word
-I2CS_TBCNT=\$54A! USCI_B0 byte counter threshold
-I2CS_RXBUF=\$54C! USCI_B0 Receive Buffer 8
-I2CS_TXBUF=\$54E! USCI_B0 Transmit Buffer 8
-I2CS_I2COA0=\$554! USCI_B0 I2C Own Address 0
-I2CS_ADDRX=\$55C! USCI_B0 Received Address Register
-I2CS_I2CSA=\$560! USCI_B0 I2C Slave Address
-I2CS_IE=\$56A! USCI_B0 Interrupt Enable
-I2CS_IFG=\$56C! USCI_B0 Interrupt Flags Register
-
-CD_SD=\$10! P4.4 as Card Detect
-SD_CDIN=\$221!
-
-CS_SD=\$20! P2.5 as Card Select
-SD_CSOUT=\$203!
-SD_CSDIR=\$205!
-
-BUS_SD=\$7000! pins P4.5 as UCB1CLK, P4.6 as UCB1SIMO & P4.7 as UCB1SOMI
-SD_SEL=\$22B! P4SEL0 to configure UCB1
-SD_REN=\$227! P4REN to configure pullup resistors
+LCD_DB=\$0F; P6.3210
+;LCD timer TB0
+LCD_TIM_CTL=\$380
+LCD_TIM_CCTLn=\$386; TB0CCTL2
+LCD_TIM_CCR0=\$392
+LCD_TIM_CCRn=\$396; TB0CCR2
+LCD_TIM_EX0=\$3A0
+;WATCHDOG timer TB1
+WDT_TIM_CTL=\$3C2
+WDT_TIM_CCTL0=\$3C2
+WDT_TIM_CCR0=\$3D2
+WDT_TIM_EX0=\$3E0
+WDT_TIM_0_VEC=\$FFF4; TB1_0_VEC
+;IR_RC5
+RC5_=RC5_;
+IR_IN=\$201;
+IR_OUT=\$203;
+IR_DIR=\$205;
+IR_REN=\$209;
+IR_IES=\$219;
+IR_IE=\$21B;
+IR_IFG=\$21D;
+IR_VEC=\$FFD2; P2 int
+RC5=4; P2.2
+;IR_RC5 timer
+RC5_TIM_CTL=\$400; TB2CTL
+RC5_TIM_R=\$410; TB2R
+RC5_TIM_EX0=\$420; TB2EX0
+; --------------------------------------------
+
+;Software I2C_Multi_Master
+I2CSMM_IN=\$220;
+I2CSMM_OUT=\$222;
+I2CSMM_DIR=\$224;
+I2CSMM_REN=\$226;
+I2CSMM_IES=\$238;
+I2CSMM_IFG=\$23C;
+SMM_SDA=4; P3.2
+SMM_SCL=8; P3.3
+SMM_BUS=\$0C;
+
+;hardware I2C_Multi_Master
+I2CMM_IN=\$200;
+I2CMM_OUT=\$202;
+I2CMM_DIR=\$204;
+I2CMM_REN=\$206;
+I2CMM_SEL=\$20A; SEL0
+I2CMM_VEC=\$FFE0; UCB0
+MM_SDA=4; P1.2
+MM_SCL=8; P1.3
+MM_BUS=\$0C;
+
+;hardware I2C_Master
+I2CM_IN=\$200;
+I2CM_OUT=\$202;
+I2CM_DIR=\$204;
+I2CM_REN=\$206;
+I2CM_SEL=\$20A; SEL0
+I2CM_VEC=\$FFE0; UCB0
+M_SDA=4; P1.2
+M_SCL=8; P1.3
+M_BUS=\$0C;
+
+;hardware I2C_Slave
+I2CS_IN=\$200;
+I2CS_OUT=\$202;
+I2CS_DIR=\$204;
+I2CS_REN=\$206;
+I2CS_SEL=\$20A; SEL0
+I2CS_VEC=\$FFE0; UCB0
+S_SDA=4; P1.2
+S_SCL=8; P1.3
+S_BUS=\$0C;
+I2CMM_VEC=\$FFE0; UCB0
+
+I2CM_CTLW0=\$540; USCI_B0 Control Word Register 0
+I2CM_CTLW1=\$542; USCI_B0 Control Word Register 1
+I2CM_BRW=\$546; USCI_B0 Baud Word Rate 0
+I2CM_STATW=\$548; USCI_B0 status word
+I2CM_TBCNT=\$54A; USCI_B0 byte counter threshold
+I2CM_RXBUF=\$54C; USCI_B0 Receive Buffer 8
+I2CM_TXBUF=\$54E; USCI_B0 Transmit Buffer 8
+I2CM_I2COA0=\$554; USCI_B0 I2C Own Address 0
+I2CM_ADDRX=\$55C; USCI_B0 Received Address Register
+I2CM_I2CSA=\$560; USCI_B0 I2C Slave Address
+I2CM_IE=\$56A; USCI_B0 Interrupt Enable
+I2CM_IFG=\$56C; USCI_B0 Interrupt Flags Register
+
+I2CS_CTLW0=\$540; USCI_B0 Control Word Register 0
+I2CS_CTLW1=\$542; USCI_B0 Control Word Register 1
+I2CS_BRW=\$546; USCI_B0 Baud Word Rate 0
+I2CS_STATW=\$548; USCI_B0 status word
+I2CS_TBCNT=\$54A; USCI_B0 byte counter threshold
+I2CS_RXBUF=\$54C; USCI_B0 Receive Buffer 8
+I2CS_TXBUF=\$54E; USCI_B0 Transmit Buffer 8
+I2CS_I2COA0=\$554; USCI_B0 I2C Own Address 0
+I2CS_ADDRX=\$55C; USCI_B0 Received Address Register
+I2CS_I2CSA=\$560; USCI_B0 I2C Slave Address
+I2CS_IE=\$56A; USCI_B0 Interrupt Enable
+I2CS_IFG=\$56C; USCI_B0 Interrupt Flags Register
+
+CD_SD=\$10; P4.4 as Card Detect
+SD_CDIN=\$221;
+
+CS_SD=\$20; P2.5 as Card Select
+SD_CSOUT=\$203;
+SD_CSDIR=\$205;
+
+BUS_SD=\$7000; pins P4.5 as UCB1CLK, P4.6 as UCB1SIMO & P4.7 as UCB1SOMI
+SD_SEL=\$22B; P4SEL0 to configure UCB1
+SD_REN=\$227; P4REN to configure pullup resistors
OSDN Git Service
