static struct fixed_voltage_config mx21ads_lcd_regulator_pdata = {
.supply_name = "LCD",
.microvolts = 3300000,
- .enable_high = 1,
.init_data = &mx21ads_lcd_regulator_init_data,
};
static struct gpiod_lookup_table mx27ads_lcd_regulator_gpiod_table = {
.dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
.table = {
- GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_LOW),
{ },
},
};
static struct fixed_voltage_config brownstone_v_5vp = {
.supply_name = "v_5vp",
.microvolts = 5000000,
- .enable_high = 1,
.enabled_at_boot = 1,
.init_data = &brownstone_v_5vp_data,
};
.supply_name = "modem_nreset",
.microvolts = 3300000,
.startup_delay = 25000,
- .enable_high = 1,
.enabled_at_boot = 1,
.init_data = &modem_nreset_data,
};
static struct fixed_voltage_config keybrd_pwr_config = {
.supply_name = "keybrd_pwr",
.microvolts = 5000000,
- .enable_high = 1,
.init_data = &keybrd_pwr_initdata,
};
.supply_name = "vwlan",
.microvolts = 1800000, /* 1.8V */
.startup_delay = 50000, /* 50ms */
- .enable_high = 1,
.init_data = &pandora_vmmc3,
};
.supply_name = "camera_vdd",
.input_supply = "vcc cam",
.microvolts = 2800000,
- .enable_high = 0,
.init_data = &camera_dummy_initdata,
};
static struct fixed_voltage_config camera_regulator_config = {
.supply_name = "camera_vdd",
.microvolts = 2800000,
- .enable_high = 0,
.init_data = &camera_regulator_initdata,
};
.dev_id = "reg-fixed-voltage.1",
.table = {
GPIO_LOOKUP("gpio-pxa", GPIO50_nCAM_EN,
- NULL, GPIO_ACTIVE_HIGH),
+ NULL, GPIO_ACTIVE_LOW),
{ },
},
};
static struct fixed_voltage_config audio_va_config = {
.supply_name = "audio_va",
.microvolts = 5000000,
- .enable_high = 1,
.enabled_at_boot = 0,
.init_data = &audio_va_initdata,
};
.dev_id = "reg-fixed-voltage.0",
.table = {
GPIO_LOOKUP("gpio-pxa", ZEUS_CAN_SHDN_GPIO,
- NULL, GPIO_ACTIVE_HIGH),
+ NULL, GPIO_ACTIVE_LOW),
{ },
},
};
static struct fixed_voltage_config zeus_ohci_regulator_config = {
.supply_name = "vbus2",
.microvolts = 5000000, /* 5.0V */
- .enable_high = 1,
.startup_delay = 0,
.init_data = &zeus_ohci_regulator_data,
};
static struct fixed_voltage_config assabet_cf_vcc_pdata __initdata = {
.supply_name = "cf-power",
.microvolts = 3300000,
- .enable_high = 1,
};
static struct gpiod_lookup_table assabet_cf_vcc_gpio_table = {
static struct fixed_voltage_config cn12_power_info = {
.supply_name = "CN12 SD/MMC Vdd",
.microvolts = 3300000,
- .enable_high = 1,
.init_data = &cn12_power_init_data,
};
static struct fixed_voltage_config sdhi0_power_info = {
.supply_name = "CN11 SD/MMC Vdd",
.microvolts = 3300000,
- .enable_high = 1,
.init_data = &sdhi0_power_init_data,
};
*/
.microvolts = 2000000, /* 1.8V */
.startup_delay = 250 * 1000, /* 250ms */
- .enable_high = 1, /* active high */
.enabled_at_boot = 0, /* disabled at boot */
.init_data = &bcm43xx_vmmc_data,
};
struct gpio_desc *gpiod;
u32 enable_count; /* a number of enabled shared GPIO */
u32 request_count; /* a number of requested shared GPIO */
- unsigned int ena_gpio_invert:1;
};
/*
}
pin->gpiod = gpiod;
- pin->ena_gpio_invert = config->ena_gpio_invert;
list_add(&pin->list, ®ulator_ena_gpio_list);
update_ena_gpio_to_rdev:
if (enable) {
/* Enable GPIO at initial use */
if (pin->enable_count == 0)
- gpiod_set_value_cansleep(pin->gpiod,
- !pin->ena_gpio_invert);
+ gpiod_set_value_cansleep(pin->gpiod, 1);
pin->enable_count++;
} else {
/* Disable GPIO if not used */
if (pin->enable_count <= 1) {
- gpiod_set_value_cansleep(pin->gpiod,
- pin->ena_gpio_invert);
+ gpiod_set_value_cansleep(pin->gpiod, 0);
pin->enable_count = 0;
}
}
int gpio_mux = pdata->gpio_ren[id];
config->ena_gpiod = pdata->ena_gpiods[id];
- config->ena_gpio_invert = 1;
/*
* GPI pin is muxed with regulator to control the
of_property_read_u32(np, "startup-delay-us", &config->startup_delay);
- /*
- * FIXME: we pulled active low/high and open drain handling into
- * gpiolib so it will be handled there. Delete this in the second
- * step when we also remove the custom inversion handling for all
- * legacy boardfiles.
- */
- config->enable_high = 1;
- config->gpio_is_open_drain = 0;
-
if (of_find_property(np, "vin-supply", NULL))
config->input_supply = "vin";
drvdata->desc.fixed_uV = config->microvolts;
- cfg.ena_gpio_invert = !config->enable_high;
- if (config->enabled_at_boot) {
- if (config->enable_high)
- gflags = GPIOD_OUT_HIGH;
- else
- gflags = GPIOD_OUT_LOW;
- } else {
- if (config->enable_high)
- gflags = GPIOD_OUT_LOW;
- else
- gflags = GPIOD_OUT_HIGH;
- }
- if (config->gpio_is_open_drain) {
- if (gflags == GPIOD_OUT_HIGH)
- gflags = GPIOD_OUT_HIGH_OPEN_DRAIN;
- else
- gflags = GPIOD_OUT_LOW_OPEN_DRAIN;
- }
+ /*
+ * The signal will be inverted by the GPIO core if flagged so in the
+ * decriptor.
+ */
+ if (config->enabled_at_boot)
+ gflags = GPIOD_OUT_HIGH;
+ else
+ gflags = GPIOD_OUT_LOW;
/*
* Some fixed regulators share the enable line between two
* @input_supply: Name of the input regulator supply
* @microvolts: Output voltage of regulator
* @startup_delay: Start-up time in microseconds
- * @gpio_is_open_drain: Gpio pin is open drain or normal type.
- * If it is open drain type then HIGH will be set
- * through PULL-UP with setting gpio as input
- * and low will be set as gpio-output with driven
- * to low. For non-open-drain case, the gpio will
- * will be in output and drive to low/high accordingly.
- * @enable_high: Polarity of enable GPIO
- * 1 = Active high, 0 = Active low
* @enabled_at_boot: Whether regulator has been enabled at
* boot or not. 1 = Yes, 0 = No
* This is used to keep the regulator at
const char *input_supply;
int microvolts;
unsigned startup_delay;
- unsigned gpio_is_open_drain:1;
- unsigned enable_high:1;
unsigned enabled_at_boot:1;
struct regulator_init_data *init_data;
};
/**
* struct gpio_regulator_config - config structure
* @supply_name: Name of the regulator supply
- * @enable_gpio: GPIO to use for enable control
- * set to -EINVAL if not used
- * @enable_high: Polarity of enable GPIO
- * 1 = Active high, 0 = Active low
* @enabled_at_boot: Whether regulator has been enabled at
* boot or not. 1 = Yes, 0 = No
* This is used to keep the regulator at
struct gpio_regulator_config {
const char *supply_name;
- int enable_gpio;
- unsigned enable_high:1;
unsigned enabled_at_boot:1;
unsigned startup_delay;
OSDN Git Service
